VM9020TS
Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
PREPARATION
Congratulations on your purchase of the Jensen VM9020TS
Mobile Multimedia AM/FM/DVD Receiver.
Tools and Supplies
You will need these tools and supplies to install your
VM9020TS:
WARNING! To prevent damage to the touch screen
display, do not use metal, plastic or any other object to
attempt to operate the touch screen functions. The touch
screen function was designed for hand/finger operation
only.
It’s a good idea to read all of the instructions before beginning
the installation. We recommend having your Jensen
VM9020TS installed by a reputable installation shop.
•
•
•
Torx type, flat-head and Philips screwdrivers
Wire cutters and strippers
Tools to remove existing radio (screwdriver, socket
wrench set or other tools)
Electrical tape
Crimping tool
Volt meter/test light
Crimp connections
18 gauge wire for power connections
16 – 18 gauge speaker wire
Features
•
•
•
•
•
ISO Double-DIN chassis
WARNING! The monitor employs an automatic motorized
mechanism. To prevent damage to the core mechanism,
please do not push, pull or swivel the monitor manually.
•
•
•
•
•
•
Light weight proprietary DVD core mechanism
Wide screen (16:9) 6.5" TFT touch screen monitor
280 watts total system power
Center channel speaker output - 1 X 22 watts RMS, 40
watts peak
Disconnecting the Battery
To prevent a short circuit, be sure to turn off the ignition and
remove the negative (-) battery cable prior to installation.
•
•
•
•
•
•
Multi-Zone media distribution
AM / FM Tuner
TV Tuner w/diversity antenna's
Supports NTSC and PAL, auto negotiation
Full, Wide, Normal and Off (Standby) screen modes
Motorized TFT panel has 16 precise angle adjustments
via remote control or infinitely variable manual
adjustment from the front panel
WARNING! Only connect the unit to a12-volt power
supply with proper grounding.
NOTE: If the VM9020TS is to be installed in a car
equipped with an on-board drive or navigation computer,
do not disconnect the battery cable. If the cable is
disconnected, the computer memory may be lost. Under
these conditions, use extra caution during installation to
avoid causing a short circuit.
WARNING! Never install this unit where operation and
viewing could interfere with safe driving conditions.
•
Auto-activated rear view camera input - Reverse gear
over rides the TFT screen to display video from a rear
mounted camera
WARNING! To reduce the risk of a traffic accident (except
when using for rear view video camera) never use the
video display function while driving the vehicle. This is a
violation of federal law.
•
•
Over current motor protection for obstructed TFT panel
Compatible optical / SD Card formats: DVD-R/RW,
DVD+R/RW, CD-R/RW, CD-DA, MP3, WMA, HDCD,
SVCD, VCD, MPEG (MPEG 1), MPEG 4, JPEG, MP3/
WMA files burned onto a DVD+R/RW or DVD-R/RW
and Kodak Picture CD
WARNING! Never disassemble or adjust the unit without
the assistance of a professional. For details, please
consult your local car stereo specialty shop.
•
•
SD Card slot
Multi-language, multi-subtitle and multi-angle playback
options
•
•
Last position memory for optical disc.
Parental Lock - Uses a password and disc rating set-up
to prevent unauthorized user access from display
content
WARNING! To prevent injury from shock or fire, never
expose this unit to moisture or water.
WARNING! Never use irregular discs.
•
•
•
Audio Mute
5-Way joystick navigation
Two remote controls - a full function front remote control
and a limited function Kid-Zone remote control for back
seat operation
WARNING! To prevent damage to the mechanism inside
this unit, avoid impact to the TFT monitor.
•
•
Over and under voltage protection to insure the unit
operates within designed parameters
Damped DVD mechanism with 16Mbit flash memory
ESP (Electronic Shock Protection) provide smooth disc
playback under the severest road conditions
1
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
INSTALLATION
This unit is designed to fit into a 2.0 DIN dashboard opening,
found in many imported cars. The unit has threaded holes in
the chassis side panels which may be used with the original
factory mounting brackets of some Toyota, Nissan,
Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the
radio to the dashboard. Please consult with your local car
stereo specialty shop for assistance on this type of
installation.
NOTE: It is the end-users responsibility to install and
operate this unit in a manner in accordance with local,
state and federal laws. The PARKING BRAKE wire MUST
BE CONNECTED as directed in the manual.
CAUTION: Do not block the cooling fan exit. If blocked,
the unit may overheat and become damaged.
1. Remove the existing factory radio from the dashboard or
center console mounting. Save all hardware and brack-
ets as they will be used to mount the new radio.
2. Remove the factory mounting brackets and hardware
from the existing radio and attach them to the new radio.
Using the iAUX3 External AV Connector
The iAUX3 allows you to connect a variety of external
devices, including a VCR, DVD player, portable MP3 player,
etc., to your VM9020TS without removing the radio.
To install the iAUX3, connect it to the AUX-IN cables on the
back of the VM9020TS (see “Wiring” on page 3), and then
install the iAUX3 in a location convenient for plugging in
auxiliary devices.
ISO INSTALLATION
Using the Cosmetic Trim Ring
A trim ring is packaged with the VM9020TS for installation
flexibility. The VM9020TS will fit into most import dashes with
little or no modification to the dash board/cavity. Some US
domestic vehicle dashes will accept a Double-DIN chassis,
but there is usually a small gap between the radio and dash
piece after installation is complete. In this case, use the trim
ring to conceal any gaps that may be present.
CAUTION: Do not exceed M5 X 6 MM screw size. Longer
screws may touch and damage components inside the
chassis.
3. Place the radio in front of the dashboard opening so the
wiring can be brought through the mounting sleeve.
Follow the wiring diagram carefully and make certain all
connections are secure and insulated with wire nuts or
electrical tape. After completing the wiring connections,
plug the ISO connectors into the mating sockets on the
rear of the chassis. Turn the unit on to confirm operation
(vehicle ignition switch must be “on”). If the unit does not
operate, re-check all wiring until the problem is
corrected.
Replacing the Fuse
When replacing the fuse, use a new 10A replacement fuse.
Using a fuse with an improper rating could damage the unit
and cause a fire.
4. Mount the new radio assembly to the dashboard or
center console using the reverse procedure in step 1.
CAUTION: For proper operation of the CD player, the
chassis must be mounted within 30° of horizontal. Make
sure the unit is mounted within this limitation.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
WIRING
<(//2:
Additional
Rear Monitor
V,'(2ꢀOUT
ꢀ
:+,7(
5('
HEADPHONE
MULTIZONE
:LUHOHVVꢀ
+HDGSKRQH
ꢀ
HEADPHONE
MULTIZONE
ꢀ
Multizone
Video
MILTIIZONE
VIDEO
<(//2:
ꢀ
5DGLRꢀ$XWRꢀꢀ$QWHQQD
&DUꢀ33KRQH
79ꢀ$QWWHQQDD1
79ꢀ$QWHHQQDꢉ
79ꢀ$QWHHQQDꢊ
79ꢀ$QWHQQDꢋ
%/8(
3
AUDIO VIDEO INPUT
3.5mm
3.5mm
iAUX 3
([WHUQDOꢀ$9ꢀꢀ6\VWHP
%/8(ꢂ:+,7(
3ꢁ&217
ꢆ
%$77(5<
([WHUQDOꢀ3RZHUꢀ$PSOLILHU
5HDUꢀ9LHZꢀꢀ9LGHRꢀ
&DPHUD
*HDUER[ꢀ66ZLWFK
NOTE: The white multipin connector will not be used in every installation. In this case, it
can be cut-off and discarded. This will not void any warranty that the unit may have.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
CONTROLS AND INDICATORS
1. POWER/MUTE
Press the POWER/MUTE button (1) once to turn the unit on.
Press again to mute the volume. Press and hold to turn the
unit off.
2. AUDIO/LOC
Press the AUDIO/LOC button (2) to access the audio menu
and change and/or confirm audio settings. Press and hold to
activate or deactivate the Local (LOC) setting.
3. VOL +
Press to increase the volume.
4. VOL -
Press to decrease the volume.
5. Joystick/ENTER
Press in on the joystick to perform the “enter” function during
various applications. Push the key up, down, left or right to
perform the following tasks:
6. Joystick/
•
•
•
•
DVD Mode: Press once for fast forward/fast reverse.
TUNER Mode: Press to go up one frequency step.
MENU Mode: Press once to move the cursor up.
TV Mode: Press once to select a stored TV channel.
7. Joystick/
•
•
•
•
DVD Mode: Press once for slow forward/slow reverse.
10. TUNER
15. CH-
TUNER Mode: Press to go down one frequency step.
MENU Mode: Press once to move the cursor down.
TV Mode: Press once to select a stored TV channel.
•
Press and hold the CH- button (15) to adjust the monitor
position outward.
Press to access the radio tuner source and then to change
between AM and FM bands.
•
•
Press to play the previous preset AM/FM station.
Press to play the previous stored TV channel.
11. MENU/SRC
8. Joystick/
•
Press to access the playing source menu.
12. OPEN
DVD Mode: Press once to play back previous chapter/
track.
16. TV
Press to access the TV tuner source.
Press the OPEN button (12) to activate the automatic
mechanical system and move the TFT down, exposing the
disc and SD card slots. Press again to close the TFT.
•
TUNER Mode: Press once to auto search for the
previous available radio station. Press and hold to
increase the tuner frequency step-by-step.
MENU Mode: Press once to move the cursor to the left.
TV Mode: Press to go down one frequency step.
17. TFT Display
18. DVD
Press the access the DVD player source.
•
•
13. DISP/PIC
19. SD
Press the DISP/PIC button (13) to adjust the display aspect
of the picture to one of three settings: Wide, Full or Normal.
Press and hold to access picture settings.
•
Press to access the SD card source.
9. Joystick/
•
DVD Mode: Press once to enter the next chapter or
20. IR Remote Control Receiver
track.
14. CH+
•
TUNER Mode: Press once to auto-search the next
available radio station. Press and hold to decrease the
tuner frequency step-by-step.
MENU Mode: Press once to move the cursor to the
right.
•
Press and hold the CH+ button (14) to adjust the
monitor position upright.
•
•
Press to play the next preset AM/FM station.
Press to play the next stored TV channel.
•
•
TV Mode: Press to go up one frequency step.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
CONTROLS AND INDICATORS
21. Disc Slot
22. Eject Button
•
•
Press once to eject the disc.
Press and hold to reset the mechanism.
23. Disc Indicator
24. SD Card Slot
25. Reset Button (see page 4).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
FRONT ZONE REMOTE CONTROL
Table 1: Front Zone Remote Control Functions
Button
Name
Function
8
3
4
5
9
6
Ref #
DVD
VCD
TUNER
CD/MP3
35
1
MENU
1
Enters the main menu of the
disc
Turns on PBC when playing
VCD
2
TITLE
2
4
Enters the title menu of the
disc
Plays first ten seconds of
each chapter/title
10
13
28
25
11
Turns the power on.
Toggles on/off audio output.
Press and hold to turn the
power off.
Turns the power on.
Toggles on/off audio output.
Press and hold to turn the
power off.
Turns the power on.
Toggles on/off audio output.
Press and hold to turn the
power off.
Turns the power on.
Toggles on/off audio output.
Press and hold to turn the
power off.
MUTE/
7
26
27
15
AUDIO
5
6
Changes the audio language
for disc playback
Changes the audio language
for disc playback
REPT A-B
Setup to repeat playback
from time frame A to time
frame B
Setup to repeat playback
from time frame A to time
frame B
12
14
20
18
17
22
21
16
34
33
19
32
REPT
7
8
9
Repeats playback of current
chapter
Repeats playback of current
chapter
Repeats playback of current
track
SRC
Selects front zone playback
source
Selects front zone playback
source
Selects front zone playback
source
Selects front zone playback
source
SUBTITLE
Language selection for subti-
tle
23
24
DISP
10
11
Displays playing information
Displays playing information
Displays playing information
Display playing information
Continuously adjusts front
panel tilt angle
Continuously adjusts front
panel tilt angle
Continuously adjusts front
panel tilt angle
Continuously adjusts front
panel tilt angle
ANGLE
12
13
Continuously adjusts front
panel tilt angle
Continuously adjusts front
panel tilt angle
Continuously adjusts front
panel tilt angle
Continuously adjusts front
panel tilt angle
ANGLE
ANGLE
30
31
Plays back disc in different
angle for a scene
Plays back Picture CD with
different angle of picture dis-
played
29
14
Fast forwards the disc con-
tent
Fast forwards the disc con-
tent
Fast forwards the disc con-
tent
Fast forwards the disc con-
tent
VOL -
VOL +
15
16
17
Decreases volume
Increases volume
Decreases volume
Increases volume
Decreases volume
Increases volume
Decreases volume
Increases volume
Selects the previous chapter
for playback
Selects the previous chapter
for playback
Searches an available radio
station by decreasing tuning
frequency
Selects the previous track for
playback
18
19
Pauses playback/starts play-
back
Pauses playback/starts play-
back
Scans FM/AM radio station;
plays/stores radio station;
deletes radio station
Pauses playback/starts play-
back
Selects the next chapter for
playback
Selects the next chapter for
playback
Searches an available radio
station by increasing tuning
frequency
Selects the next track for
playback
BAND
GOTO
20
21
Stops playback
Stops playback
Selects FM/AM band
Stops playback
Goes to specific time frame
and playback
Goes to specific time frame
and playback
NOTE: Your remote control may differ slightly
from the one pictured here. The above diagram is
for illustrative purposes only.
22
23
Slow playback/slow rewind
playback
Slow playback/slow rewind
playback
ZOOM
Zooms in/out on an image
Zooms in/out on an image
6
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
Table 1: Front Zone Remote Control Functions
Function
Button
Name
Ref #
DVD
VCD
TUNER
CD/MP3
8
3
4
5
9
6
PIC
24
25
Displays set-up parameters
Displays set-up parameters
35
1
OPEN/
CLOSE
Opens/Closes the TFT moni-
tor
Opens/Closes the TFT moni-
tor
Opens/Closes the TFT moni-
tor
Opens/Closes the TFT moni-
tor
26
27
28
Decreases monitor tilt angle
Increases monitor tilt angle
Decreases monitor tilt angle
Increases monitor tilt angle
Decreases monitor tilt angle
Increases monitor tilt angle
Decreases monitor tilt angle
Increases monitor tilt angle
2
10
13
28
25
11
WIDE
Selects display mode: WIDE, Selects display mode: WIDE, Selects display mode: WIDE, Selects display mode: WIDE,
NORMAL, or FULL
NORMAL, or FULL
NORMAL, or FULL
NORMAL, or FULL
7
0, 1, 2, 3, 4, 29
5, 6, 7, 8, 9,
0 (Numeric
Directly accesses chapter
1-6 selects preset for current
band
Directly accesses track
26
27
15
Keypad)
DVD
SETUP
30
31
Access DVD Setup menu
Access DVD Setup menu
Access DVD Setup menu
Access DVD Setup menu
12
14
20
18
17
22
21
16
34
33
19
32
SYS
SETUP
Access System Setup menu
Access System Setup menu
Access System Setup menu
Access System Setup menu
SEL
32
33
RDM
Plays all chapters in random
order
Plays all tracks in random
order
SCN
34
35
Plays the first ten seconds of
each track
23
24
EJECT
Ejects disc
Ejects disc
Ejects disc
Ejects disc
30
31
29
NOTE: Your remote control may differ slightly
from the one pictured here. The above diagram is
for illustrative purposes only.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
MULTI-ZONE REMOTE CONTROL
Table 2: Multi-Zone Remote Control Functions
Button
Name
Function
Ref #
DVD
VCD
MENU
TITLE
1
2
3
5
7
8
9
Enters the main menu of the disc
Enters the title menu of the disc
Turns on PBC when playing VCD
Plays first ten seconds of each chapter/title
Toggles on/off audio output
8
3
MUTE
Toggles on/off audio output
1
2
5
9
AUDIO
REPT
Switches the audio language for disc playback
Setup to repeat playback of each chapter/title/disc
Selects playing mode for rear zone
Language selection for subtitle
Setup to repeat playback of each chapter/title/disc
Selects playing mode for rear zone
R.SRC
SUBTITLE
14
18
14
Fast forwards the disc content
Fast forwards the disc content
17
Selects the previous track/chapter for playback
Selects the previous track/chapter for playback
19
17
22
18
19
Pauses playback/Starts playback
Pauses playback/Starts playback
Selects the next track/chapter for playback
Selects the next track/chapter for playback
GOTO
21
22
Goes to specific time frame and playback
Slow playback/slow rewind playback
Goes to specific time frame and playback
Slow playback/slow rewind playback
7
0, 1, 2, 3, 4, 29
5, 6, 7, 8, 9,
0 (Numeric
Keypad)
Directly accesses chapter
21
29
NOTE: Your remote control may differ slightly
from the one pictured here. The above diagram is
for illustrative purposes only.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
USING THE TFT MONITOR
Open/Close TFT Monitor
Open TFT Monitor
NOTE: The default adjustment is “0” in PAL mode. Tint is
unavailable for adjustment.
FULL
The entire screen is extended
horizontally to the aspect ratio of 16 to
9. The extension ratio is the same at
any point.
Press the OPEN button (12) on the front panel or press the
(
) button (25) of the front zone remote control to open/
Parameter Adjustment Procedure
close the monitor.
1. Enter Picture Quality Setting mode:
Press the PIC button (24) on the remote or press and
hold the DISP/PIC button (13) on the unit.
2. Select Item to Set:
TFT Monitor Auto Open
•
If “TFT Auto Open” is “on” when the unit is turned on,
the monitor automatically moves to the last viewing
position.
WIDE
The screen is extended horizontally to
the aspect ratio of 16 to 9. The
extension ratio increases toward the
right and left ends of the screen.
Press the ( ) ( ) buttons (14, 22) on the remote or
press and hold the ( ) or ( ) buttons (18, 19) on the
monitor panel.
•
If “TFT Auto Open” is ”off” when the unit is turned on,
press the OPEN button (12) or ( ) button (25) on the
front zone remote control to move the monitor into the
desired viewing position.
3. Set Parameters:
Press ( ) ( ) buttons (17, 19) on the remote or press
NORMAL
(
) ( ) buttons (8, 9) on the unit.
The conventional display image has a
4 to 3 ratio of horizontal to vertical,
leaving a blank area on the right and
left sides of the display.
Monitor Tilt Angle Adjustment
4. Exit Picture Quality Setting Mode:
A known characteristic of LCD panels is the quality of the
display in relationship to the viewing angle. The monitor
angle can be adjusted for optimum viewing using one of the
following methods:
Press the PIC button (24) on the remote or press and
hold the DISP/PIC button (13) on the monitor panel.
Parking Brake Inhibit
•
When the “PRK SW” cable is connected to the brake
switch, the display on the TFT monitor will display video
only when the vehicle is applied.
OFF
•
Press the ( ) or ( ) button (3, 4) on the remote
control or the CH+ or CH- button (14, 15) on the front of
the unit to adjust the tilt angle of the screen one step at
a time.
•
•
Parking brake function is overridden when the video
source is set to CAMERA.
When the parking brake inhibit is active, the front
monitor displays “Parking Is On”, preventing the driver
from watching content while driving. Rear video screens
are not affected.
•
Press and hold the to adjust the tilt angle of the screen
one step at a time.
Image Setting
Video Output Format
Rear Camera Mode
When the vehicle is placed in "Reverse", and an optional rear
camera is connected to the VM9020TS, the TFT monitor will
automatically switch to the camera input source.
Table 3 shows the video output format for each playing
source.
Monitor Movement Mechanism
If an obstruction occurs in the monitor path, the motion will
stop automatically to prevent damage to the mechanism or
monitor.
Aspect Ratio
Table 3: Video Output Formats
The following sources only have the WIDE and OFF aspect
ratio option: AM / FM Tuner, CD-DA, SD Card, DVD+R/RW,
DVD-R/RW and CD-R/RW with music files. Press the WIDE
button (28) on the remote control to adjust the aspect ratio as
follows:
Playing Source
Video Output Format
Normal operation is resumed by pressing the OPEN button
(12) or disconnecting and reconnecting the power.
TUNER
RGB Mode
DVD
RGB Mode
CVBS Mode
CVBS Mode
CVBS Mode
AUX IN
CAMERA
TV
*CVBS – Composite Video Baseband Signal
Adjustable Parameters
While in DVD or TUNER mode, the only parameter that can
be adjusted is brightness (BRIGHT). To access “PICTURE”,
“COLOR”, “CONTRAST”, and “TINT” you must be in AUX or
CAMERA mode.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
OPERATING INSTRUCTIONS
To program a specific volume level, push and hold the
AUDIO button (2) while the yellow volume bar is displayed on
the screen. The unit will beep two times to confirm your turn-
on volume setting.
The Loud function compensates for deficiencies in sound
ranges at low levels. Loudness levels range from 1-4 or “off”.
When the Loud function is on, LOUD is displayed on the
screen.
Power On / Off
Press the /MUTE button (1) to turn the unit on. The buttons
on the front of the unit will light up.
Press and hold the /MUTE button (1) on the front panel or
the POWER button (4) on the remote to power off the unit.
Exiting the Audio Control Menu
Audio Control Menu
Press and hold the AUDIO/LOC button (2) or stop making
adjustments for a few seconds to exit the audio control menu.
The Audio Control feature allows you to easily adjust your
audio system to meet the acoustical characteristics of your
vehicle, which vary depending on the type of vehicle and its
measurements. To get the best possible sound quality from
your new system, be sure to adjust the settings for the
speakers as well. Proper setting of the Fader and Balance
boosts the effects of the cabin equalizer.
Audible Beep Confirmation
An audible beep tone confirms each function selection. The
beep tone cannot be disabled.
Six-Channel Audio Control
Mute
NOTE: Before adjusting the volume of any speaker,
please refer to “Surround Setup” on page 18.
Press the /MUTE button (1) on the front panel or remote (3)
to mute the volume from the unit. Press the MUTE button
again to restore the volume. The mute icon flashes on the
right side of the screen. Adjusting the volume or using any of
the audio set-up features cancels the mute function.
Accessing the Audio Control Menu
Table 5: 6-Channel Audio Adjustments
Press the AUDIO/LOC button (2) on the front panel to display
the “AUDIO” menu.
Item
Adjustable Range
Selecting an Audio Feature for Adjustment
Master Volume
00 to 40
Playing Source Selection
Press the ( )/( ) buttons (8, 9) on the joystick or the ( )/
Front Left Channel Volume
Front Right Channel Volume
Rear Left Channel Volume
Rear Right Channel Volume
Center Channel Volume
Subwoofer Volume
-10 to +10
-10 to +10
-10 to +10
-10 to +10
-10 to +10
-10 to +10
Press the SRC button (11) on the remote to change between
available playing sources in the following order: TUNER,
DVD, AUX IN or CAMERA (rear view video camera). The
playing mode is displayed on the screen.
(
) buttons (17, 19) on the remote control to select the audio
feature to be adjusted.
Adjusting an Audio Feature
Press the
or
buttons (14, 22) on the remote control or
Press the MENU/SRC button (11) on the unit to access the
playing source menu. Use the direction buttons on the
joystick (6, 7, 8, 9) or remote control (14, 17, 18, 19, 22) to
the or buttons (6, 7) on the joystick to adjust the
selected feature to the desired setting.
Table 4: Audio Adjustments
select a playing source, then press the
button (18) or the
Rear Zone
joystick enter button (5) to enter the selected source.
Audio Function
Adjustable Range
If a monitor is installed in the rear zone and connected to the
rear zone AV output, passengers in the back seat can control
the DVD output using the rear zone remote control. See
“Multi-Zone Remote Control” on page 8 for instructions.
AUX IN Mode
EQ
User
Flat
An external peripheral device can be connected to this unit
via RCA output and “AUX-IN”.
Jazz
Pop
CAMERA Mode
System Reset
“CAMERA” mode is only available if the camera is connected
and during reverse driving. To install a rear view video
camera, connect the video input cable to the camera output
cable.
To correct a system halt or other illegal
operation, use the tip of a pen to press
the RESET button (25) located on the
front bottom-left corner of the TFT screen. After a system
reset, the unit restores all factory default settings.
[RESET] Button
Classical
Rock
Vocal
Bass
-14 to +14
-14 to +14
-9 to +9
-9 to +9
-7 to +7
Off, 1-4
Volume Adjustment
Treble
Fade
Bal
To increase the volume level, press the VOL + button (3) on
the front panel or remote control. To decrease the volume
level, press the VOL - button (4) on the front panel or remote
control.The volume ranges from “0” to “40”. When the volume
level reaches “0” or “40”, a triple beep sounds, indicating that
the adjustment limit has been reached. The screen displays
the volume level for 3 seconds.
NOTE: If the unit is reset while a DVD is playing, the DVD
resumes play once the reset is complete.
SW
Line Mute
Loud
If the “MUTE” wire is connected, audio output mutes when a
telephone call is received by the car phone or when verbal
navigation is performed. See “Wiring” on page 3.
Programmable Turn-On Volume
NOTE: The Bass and Treble levels are only adjustable
when EQ is set to “User” mode.
This feature allows the user to select a turn-on volume setting
regardless of the volume setting prior to turning the unit off.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
SYSTEM SETUP MENU
In “System Setup” mode, “ASP CONFIG” and “GENERAL
SETUP” are available for adjustment. Setup can be
performed by pressing the dedicated button on the remote
control or by pressing the MENU/SRC button (11) on the front
panel.
Adjusting a Feature
1. Enter the option field for the feature you want to adjust
Adjusting the Clock
1. Access the “Clock” setting under the General Setup
menu.
by pressing the
button (18) on the remote or by
pressing the ENTER (joystick) button (5) on the unit. A
submenu appears in a second row with the selected
option highlighted in light blue.
2. Press the
or
buttons (14, 22) on the remote
control or the or buttons (6, 7) on the joystick to
move the cursor to the “Hour” or “Min” position.
3. Press the , or
control or the or buttons (8, 9) on the joystick to
adjust the hour or minutes.
4. Press the button (14) on the remote control to confirm
setup.
For system settings, press the SYS SETUP button (31) on
the remote control or touch “SETUP” on the screen to enter
the “SETUP” menu. “SYS SETUP” is highlighted in green.
2. Select a new value by pressing the
or buttons (14,
buttons (17, 19) on the remote
22) on the remote control or the or buttons (6, 7) on
the joystick.
3. Confirm your selection by pressing the
General Setup Menu
Accessing the General Setup Menu
,
, or
buttons (14, 17, 19) on the remote control, or the or
button (8, 9) on the joystick. The new value is
highlighted in light blue and setup is complete.
To access the “GENERAL SETUP” Menu, press the direction
buttons on the joystick (6, 7, 8, 9) or remote control (14, 17,
18, 19, 22) to highlight “GENERAL SETUP” in green.
Returning to the System Setup Menu
To return to the System Setup menu, move to BACK, then
Table 6: General Setup Menu Features
press the
button (18) on the remote control.
ASP (Audio Sound Processing) Config
Menu
The ASP Config Menu allows you to make fine audio
adjustments.
Setting
Options
Function
DIRECTION BUTTONS
Radio
USA1
Select the appropriate setting
based on the country in which you
reside.
S. Amer 1
Arabia
China
Accessing the ASP Config Menu
To access the “ASP CONFIG” Menu from the “SYSTEM
SETUP” menu, press the direction buttons on the joystick
(16, 17, 18, 19) or remote control (14, 17, 18, 19, 22) to
S. Amer 2
Europe
Korea
highlight “ASP CONFIG” in green. Press the
button (18)
on the remote control to enter the “ASP CONFIG” menu. A
menu appears with the option for the first item, “Bass Center
Freq”, highlighted in light blue.
Clock Mode
12H
Clock displays 12 hour time using
AM and PM.
Press the
button (18) on the remote control to enter the
24H
Clock displays 24 hour time up to
23:59.
“GENERAL SETUP” menu. A menu appears with the option
for the first item, “Radio”, highlighted in light blue.
Screen Saver On
Off
Turn screen saver on/off.
TV System
Auto
The color signal output is switched
automatically based on the current
disc.
NTSC
PAL
The color signals are output in the
standard NTSC format.
The color signals are output in the
standard PAL format.
TFT Auto
Open
On
The TFT panel automatically opens
when the unit is turned on.
Off
You must press the OPEN button
(12) to open the TFT panel.
OSD Lan-
guage
English
(HH:MM)
The menus are displayed in English
only.
Adjusting a Feature
Clock
See “Adjusting the clock” to learn
how to set the clock.
Selecting a Feature for Adjustment
1. Enter the option field for the feature you want to adjust
Press the
or
buttons (14, 22) on the remote control or
by pressing the
button (18) on the remote or by
BACK
Return to previous menu.
the or buttons (6, 7) on the joystick to select the feature
to be adjusted.
pressing the ENTER (joystick) button (5) on the unit. A
11
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
submenu appears in a second row with the selected
option highlighted in light blue.
Selecting a Source for the Rear Zone
MULTI-ZONE OPERATION
To access the rear zone SOURCE MENU, touch the top right
corner of the screen, near the Multi-ZONE icon.
Independent sources can be played simultaneously on the
VM9020TS. For example, a video game console can be seen
on the front screen while DVD video is available to rear
passengers. For example, DVD is selected as the front
source and SD Card is selected for the rear source or SD
Card is selected as the front source and DVD is selected for
the rear source. In the first case, both sources will switch to
SD Card. In the second case, both sources will switch to the
DVD source because the multimedia processor is shared
between optical and SD Card media.
2. Select a new value by pressing the
or buttons (14,
22) on the remote control or the or buttons (6, 7) on
the joystick.
3. Confirm your selection by pressing the
,
, or
buttons (14, 17, 19) on the remote control, or the or
button (8, 9) on the joystick. The new value is
highlighted in light blue and setup is complete.
Table 7: ASP Config Menu Features
Setting
Options
Function
Selecting a Source for the Front Zone
Bass Center
Freq
60Hz
According to the audio source, select
the Bass Center Frequency to
achieve the best Bass effect.
To access the FRONT ZONE SOURCE MENU, touch the
TFT screen in the top left corner of the screen.
80Hz
100Hz
130Hz
150Hz
200Hz
10KHz
12.5KHz
15KHz
17KHz
80Hz
Select the source to be directed to the rear Multi-ZONE RCA
outputs.
Treble Center
Freq
According to the audio source, select
the Treble Center Frequency to
achieve the best Treble effect.
NOTE: Optical media and an SD Card cannot be selected
from the Multi-ZONE Source Menu icon simultaneously.
Sub.W Filter
Selecting a crossover frequency sets
a cut-off frequency of the subwoofer's
LPF (low-pass filter) and the
“SMALL” speakers' HPF (high-pass
filter). The Crossover frequency set-
ting has no effect if the subwoofer is
set to “OFF” and any other speaker is
set to “LARGE”.
120Hz
160Hz
NOTE: The AM/FM tuner graphics will change to a "blue
screen" background when any optical or SD Card media
is selected from the Multi-ZONE menu. In addition, only
the top left (Front Zone Source Menu) and right (Multi-
ZONE Source Menu) quadrants of the touch screen are
active during this mode of operation.
Sub.W Phase
0D
Subwoofer output IN phase
This menu allows you to select a source for the front zone.
180D
Subwoofer output OUT OF phase
NOTE: Depending on your installa-
tion, reversing the subwoofer phase
may increase Bass output.
Bass Q-Factor 1.0
1.25
When the Bass Center Frequency is
selected, adjusting the Bass Q-Fac-
tor alters the sharpness of the Bass
output.
1.5
2.0
BACK
Return to previous menu.
Exiting the System Setup Menu
To exit setup mode and resume normal playback, press the
SYS SETUP button (31) on the remote control or the DISP
button (13) on the front panel.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
TUNER OPERATION
1. Select a band (if needed).
2. Touch AS (17) for 2 seconds to activate the Auto Store
function.
Tuner TFT Display
Select FM/AM Band
Touch the BAND button (16) on the screen, or press the
TUNER button (10) on the unit or the BAND button on the
remote control (20) to change between the following bands:
FM1, FM2, FM3, AM1, and AM2.
The new stations replace stations already stored in that band.
Local Radio Station Seeking (LOC)
Auto Tuning
Press and hold the
screen, or the button on the joystick (9) to seek the next
available radio station by increasing the tuning frequency.
Press the button again to stop searching.
When the Local function is on, only radio stations with a
strong radio signal are played. To activate the Local function
in AM/FM tuner mode, press and hold the AUDIO/LOC
button (2) on the front panel while the yellow volume bar IS
NOT visible. Press AUDIO/LOC again to turn Local off. When
the Local function is active, “LOC” appears on the screen and
a green indicator is illuminated.
button (19) on remote control or
Press and hold the
button (17) on the remote control or
screen, or the button on the joystick (8) to seek the next
available radio station by decreasing the tuning frequency.
Press the button again to stop searching.
Manual Tuning
Press the
or
buttons (14, 22) on the remote control or
screen, or the or buttons (6, 7) on the joystick to
increase or decrease the tuning frequency one step.
Press and hold the buttons to continuously tune until you
release them.
1. Current Radio Band Indicator
2. Radio Frequency Indicator
3. Clock
Using Preset Stations
Six numbered preset buttons store and recall stations for
each band. All six stored stations (P1-P6) for the current
band appear on the screen.
4. Stereo Broadcasting Indicator
5. Strong Local Signal Broadcasting Indicator: Touch and
hold to activate/deactivate Local function
6. Preset Radio Stations: Touch to recall preset stations or
touch and hold to store a station
7. Front Zone Playing Mode
8. Rear Zone Playing Mode
9. User Defined Equalizer Level
10. Loud Setting Indicator
11. Current Preset Station Indicator
Storing a Station
1. Select a band (if needed), then select a station.
2. Touch and hold an on-screen preset button (6) for three
seconds. The preset number appears at the top of the
screen.
Recalling a Station
1. Select a band (if needed).
2. Touch an on-screen preset button (6) to select the
corresponding stored station.
12.
13.
14.
15.
: Touch to seek backward
: Touch to seek forward
: Touch to tune backward one step
: Touch to tune forward one step
16. BAND: Touch to change between AM/FM bands
17. AS: Touch to automatically store stations
18. Touch this area to return to the MAIN MENU
Switch to Radio Tuner source
Press the TUNER button (10) on the front panel or the SRC
button on the remote control (8) to switch to the TUNER
source.
Auto Store (AS)
Automatic Storing of Preset Stations
To select six strong stations and store them in the current
band:
13
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
DVD PLAYER OPERATION
NOTE: When properly installed, DVD video cannot be
displayed on the main TFT screen unless the parking brake is
applied. If you attempt to play a DVD while the vehicle is
moving, the TFT screen displays “PARKING” with a blue
background. Rear video screens, if applicable, will operate
normally.
Using the Touch-Screen Controls
The touch key areas for DVD playback are outlined below.
NOTE: For VCD play, the repeat function is not available
if PBC is on.
Sectional Repeat Function (A-B)
Use the A-B function to define a specific area of a disc to
repeat.
Opening/Closing the TFT Video Screen
Opening the TFT Screen
To open the TFT video screen, press the OPEN (2) button.
The unit beeps and then open.
•
Press the REPT A-B button (6) on the remote control to
set the start point (A) of the repeated section.
Press the REPT A-B button again once you reach the
desired end point (B) of the repeated section. The
selected portion of the DVD will now repeat
continuously.
•
Closing the TFT Screen
Press the OPEN (12) button again to close the TFT screen. If
the screen is in the “IN” position, it moves out before closing.
•
Press the REPT A-B button again to cancel the A-B
section setting and stop repeat play.
Insert/Eject Disc
Random Playback
Upon inserting a DVD disc, DVD mode is entered disc play
begins. If the TFT screen is closed, the DVD indicator
appears lit on the LCD screen.
A – Return to MAIN MENU
With a DVD, VCD, or CD playing, press the RDM button (33)
on the remote control to activate random playback and play
all chapters/tracks in random order. “On” appears on the
screen.
B – DISP key: Displays playing information
C – Select previous chapter
D – Select next chapter
NOTE: If Parental Lock (Rating) is activated and the disc
inserted is not authorized, the 4-digit code must be
entered and/or the disc must be authorized (see
“RATING (Parental Lock) Menu” on page 19).
Press the
button (19) on the remote control or the
E – Display the following on-screen controls: Menu,
,
,
button on the joystick (9) to play the next random track.
,
,
,
.
Press the RDM button again to turn random play off.
Controlling Playback
Stopping Playback
You cannot insert a disc if there is already a disc in the unit or
if the power is off.
NOTE: When a VCD is playing with PBC turned “On”,
activating random playback automatically turns PBC off.
Touch the stop button ( ) on the screen or press the
BAND button (20) on the remote control to stop DVD play.
/
NOTE: CD-R/RW, DVD-R/RW, DVD+R/RWs will not play
unless the recording session is closed.
Pausing Playback
Accessing the DVD Menu
Press the MENU button (1) on the remote control to recall the
Touch the play/pause button (
button on the remote control (18) to suspend or resume
disc play.
Slow Motion Playback
) on the screen or press the
main DVD menu. Use the directional (arrow) buttons (
) on the joystick (16, 17, 18, 19) to select a title from
the menu.
,
,
Ejecting a Disc
&
Press the button (22) on the unit or remote control (25) to
eject the disc. The unit automatically reverts to Tuner mode.
You may eject a disc with the power off and the unit remains
off after the disc is ejected.
Press the
button (22) on the remote control or the
Press the TITLE button (2) on the remote control to select a
different title for playback.
button (7) on the joystick to play the current title in slow
motion at 1/2, 1/4, 1/6 or 1/7, the normal speed. Press
(18) to resume normal play. Continue pressing the
button to slow reverse.
or
Press the
button (18) on the remote control or the
Reset the Loading Mechanism
ENTER (joystick) button (20) to confirm your selection and
begin playback.
If the disc loads abnormally or an abnormal core mechanism
operation occurs, press and hold the button (22) on the
unit or remote control (25) to reset the loading mechanism.
Normal operation resumes.
Repeat Playback
Press the REPT button (7) on the remote control to alter
repeat mode according to the following:
Moving Through Chapters
Press the
button (19) on the remote control or the
•
•
•
DVD: Repeat Title, Repeat Chapter, Repeat Off
VCD (PBC Off): Repeat Single, Repeat Off
MP3: Repeat Single, Repeat Folder, Repeat Off
button on the joystick (17) to advance to the next chapter on
the DVD.
Accessing DVD Mode
To switch to DVD mode when a disc is already inserted,
press the DVD button (18) on the front panel, or press the
SRC button (8) on the remote control until DVD appears at
the bottom of the screen.
Press the
button (17) on the remote control or the
button on the joystick (16) to move to the previous chapter.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
Press the
or
buttons (14, 22) on the remote control or
Fast Forward/Fast Reverse
Zooming
the or buttons (8, 9) on the joystick to select a category
(highlighted in blue).
Press the ZOOM button (23) on the remote control to enlarge
and pan through the video image using the following options:
“Q1”, “Q2”, “Q3”, and “OFF”.
Press the
button (14) on the remote control or the
button (6) on the joystick to fast forward. Keep pressing and
releasing the button to increase the rate from “2X” to “4X”,
•
For DVD mode, you can choose Time or Title/
Chapter search.
“8X”, and “20X”. Continue pressing the
fast reverse.
or button to
Multi-Language Discs (DVD Only)
Changing Audio Language
DVD Search
Scanning
Time – Go to specific
time in current title
If you are watching a disc recorded in multiple languages,
press the AUDIO button (5) on the remote control to choose
a language.
Press the SCN button (?) on the remote control to play the
first ten seconds of each chapter. Press SCN again to stop
the scan function and play the current chapter.
Title/Chapter – Go to
specific time in a
chapter
Changing Subtitle Language
If you are watching a disc recorded in multiple languages with
subtitles, press the SUBTITLE button (9) on the remote
control to choose the language in which you would like the
subtitles to appear.
Selecting 2-Channel and 6-Channel Audio
Playback
2-Channel Audio (Down Mix) Support for CD, SD Card
and DVD
•
For VCD mode, press the GOTO button to choose
between Track Search, Disc Search and Exit.
VCD Track Search
Linear pulse code modulation (LPCM) and pulse code
modulation (PCM) support is available for CD, SD Card and
DVD discs when 2-channel audio is selected.
NOTE: During VCD playback, press the AUDIO button (5)
on the remote control to choose between Left Channel,
Right Channel, and Stereo.
Time – Go to specific
time in the current track
Track – Go to specific
6- Channel Audio Support for CD, SD Card and DVD
track
Surround I is available for decoding analog or digital 2-
channel down mixed sources. Surround II is available for
decoding digital bit-stream sources.
PBC (Play back Control) (VCD Only)
For VCDs with play back functionality, play back control
(PBC) provides additional controls for VCD playback.
VCD Disc Search
Time – Go to specific
time on disc
Press the MENU button (1) on the remote control to toggle
the PBC function “On”/”Off”. Once PBC is on, playback starts
from track one of the play list.
Track – Go to specific
track
NOTE: 2-Channel audio support is available for AM / FM
tuner, TV tuner and Auxiliary input only.
2. Enter a time into the field using the numeric keypad (29)
on the remote control.
Table 8: Speaker Output Options
NOTE: When PBC is activated, fast forward, slow
playback, and previous/next track are available. Repeat
and direct track selection are not available.
Front
Spkr
Rear
Spkr
Center
Spkr
Sub-
3. Press the
button (18) on the remote control or the
Speaker Setup
Woofer
ENTER (joystick) button (5) to go to the specified
location on the disc.
4. Press the GOTO button again to exit.
2CH mode
X
X
When PBC is activated, selecting random, scan, or search
playback automatically deactivates PBC.
Play 2CH audio in
6CH mode with Sur-
round “Off”
X
X
Direct Chapter / Track Selection
During DVD, VCD and CD
playback, you can use the numeric
keypad on the remote control (29)
to access a track directly.
Playback Information
Play 2-channel (down
mix) audio in 6-chan-
nel mode with Sur-
round I "ON"
X
X
X
X
X
During DVD and VCD playback, press the DISP button (10)
on the remote control to display playback information on the
screen, including the media playing and current playback
time.
Play 6-channel audio
in 6-channel mode
with Surround II "ON"
X
X
Viewing an Alternate
Picture Angle (DVD
Only)
DVD Playback Information
The following information is displayed at the bottom of the
screen during DVD playback:
Goto Search
During DVD or VCD playback, perform the following steps to
use the GOTO feature to access a specific location on a disc:
Some DVDs contain scenes that have been shot
simultaneously from different angles. For discs recorded with
multiple angles, press the ANGLE button (13) on the remote
control to toggle available angles of the on-screen image.
1. Press the GOTO button (21) on remote control to enter
“GO TO” mode.
•
T : 5/8 – “5 / 8" indicates the fifth of 8 titles on the DVD is
currently playing.
•
C : 2/16 – “2 / 16" indicates that the second of 16 titles
on the DVD is currently playing.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
•
•
00:41:28 – “00:41:28” indicates the playback time of the
current title.
2 / 6 Eng – The language display information
indicates the second language out of 6 (English) is
currently being used.
•
Rear: AUX IN – “AUX IN” is the current playing source
for the rear zone.
EQ:FLAT – The equalizer setting is FLAT.
Loud: Level 1 – The Loud option is set to Level 1
loudness.
•
•
The following information appears at the bottom of the screen
during DVD playback:
General Disc Information
Table 9: Disc Properties
Front: DVD
Rear: AUXIN
SURR II
DSP
Symbo
l
Max Play
Time
12cm Disc Properties
•
•
Front: DVD is the current playback source for the front
zone.
Rear: AUX IN is the current playback source for the rear
zone.
"Surround II" is the selected playback audio encoding
process.
"DSP" indicates Digital Signal Processing.
(MPEG 2
Method)
133 minutes
242 minutes
266 minutes
484 minutes
Single side single layer (DVD-5)
Single side double layer (DVD-9)
Double side single layer (DVD-10)
Double side double layer (DVD-18)
(MPEG 1
Method)
74 minutes
Single side single layer (VCD)
Single side single layer
VCD Playback Information
74 minutes
The following information is displayed on the screen during
VCD playback:
Table 10: Disc Symbols
Symbol
Meaning
•
•
VCD2.0 – Format of current disc.
T: 6/18 – “6/18” indicates the sixth of 18 tracks on the
VCD is currently playing.
00:02:18 – “00:02:18” indicates the playback time of the
current track.
Number of voice languages recorded. The num-
ber inside the icon indicates the number lan-
guages on the disc (maximum of 8).
•
Number of subtitle languages available on the
disc (maximum of 32).
The following information appears on the screen during VCD
playback in 6-Channel mode:
Number of angles provided (maximum of 9).
Front: DVD
Rear: AUXIN
MPEG
MOVIE
Aspect ratios available. “LB” stands for Letter Box
and “PS” stands for Pan/Scan. In the example on
the left, the 16:9 video can be converted to Letter
Box video.
•
•
Front: DVD – “DVD” is the current playing source for the
front zone.
Indicates the region code where the disc can be
played.
Rear: AUX IN – “AUX IN” is the current playing source
for the rear zone.
“MPEG” is the decoding method in use.
"Movie" indicates that movie effects are being applied to
the audio sound track from the VCD.
•
•
•
•
Region 1: USA, Canada, East Pacific Ocean
Islands
Region 2: Japan, Western Europe, Northern
Europe, Egypt, South Africa, Middle East
Region 3: Taiwan, Hong Kong, South Korea,
Thailand, Indonesia, South-East Asia
Region 4: Australia, New Zealand, Middle and
South America, South Pacific Ocean Islands/
Oceania
The following information appears on the screen during VCD
playback in 2-Channel mode:
•
Region 5: Russia, Mongolia, India, Middle
Asia, Eastern Europe, North Korea, North
Africa, North-West Asia
•
Front: DVD – “DVD” is the current playing source for the
front zone.
•
•
Region 6: Mainland China
ALL: All regions
16
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
DVD SETUP MENU
In “DVD Setup” mode, “LANGUAGE”, “VIDEO”, “AUDIO”
“SURR SETUP”, “SURROUND FX”, and “RATING” (parental
lock) are available for setup. This operation can be performed
using the remote control or joystick controls.
Table 11: LANGUAGE Menu Features
DIRECTION BUTTONS
Setting
Options
Function
DVD Menu
English
Select the default language in which
you would like the DVD menu (if appli-
cable) to be displayed.
Accessing the DVD Setup Screen
BACK
Return to previous menu.
Setup can be performed by pressing the dedicated button on
the remote control or by pressing the MENU/SRC button (11)
on the front panel.
VIDEO Menu
For system settings, press the DVD SETUP button (30) on
the remote control or touch “SETUP” on the screen to enter
the “SETUP” menu. “SYS SETUP” is highlighted in green.
Table 12: VIDEO Menu Features
Setting Options
Function
Selecting a Feature for Adjustment
To access the “DVD SETUP” Menu, press the button
button (7) on the remote control to choose the “DVD SETUP”
TV Shape
(Aspect
Ratio)
4:3 PS
4:3 LB
16:9
With 16:9 display, the left and right sides
are cut off.
Once inside a menu, press the
or
buttons (14, 22) on
the remote control or the or buttons (6, 7) on the joystick
to select the feature to be adjusted.
With 16:9 display, the top and bottom are
cut off.
option, then press the
button (18), or just touch “DVD
SETUP” on the screen. “LANGUAGE” is highlighted in green.
Adjusting a Feature
1. Enter the option field for the feature you want to adjust
Image is presented in wide view with a
16:9 aspect ratio.
Angle
Mark
On
Off
Angle indicator (if applicable) is shown.
Angle indicator is not shown.
by pressing the
button (18) on the remote or by
pressing the ENTER (joystick) button (5) on the unit. A
submenu appears in a second row with the selected
option highlighted in light blue.
View Mode Fill
Original
2. Select a new value by pressing the
or buttons (14,
H Fit
22) on the remote control or the or buttons (6, 7) on
the joystick.
W Fit
3. Confirm your selection by pressing the
,
, or
Fit to
Scrn
buttons (14, 17, 19) on the remote control, or the or
button (8, 9) on the joystick. The new value is
highlighted in light blue and setup is complete.
Pan Scan
BACK
Return to previous menu.
LANGUAGE Menu
If a DVD supports more than 1 Subtitle or Audio language, all
the languages are available for selection during playback. If
the selected language is not supported by the DVD, then the
default language is used. During playback, press the
SUBTITLE (9) or AUDIO (5) button on the remote control to
change the language directly. This will not effect the DVD
menu settings.
NOTE: For standard discs not formatted for
“widescreen”, use of the 16:9 aspect ratio will result in
image distortion.
NOTE: Once the DVD setup is complete, the settings are
memorized. To return to the factory default settings,
press the RESET button (25) on the front panel.
Accessing a Menu
Table 11: LANGUAGE Menu Features
To access a menu (LANGUAGE, VIDEO, AUDIO, SURR
SETUP, SURROUND FX, or RATING), press the direction
buttons on the joystick (6, 7, 8, 9) or remote control (14, 17,
18, 19, 22) to highlight the desired menu in green. You can
also touch the on-screen menu selection to access that
menu.
Setting
Options
Function
Subtitle
English
Auto
Select the default language in which
you would like subtitles (if applicable) to
be displayed.
Off
Audio
English
Select the default language in which
you would like audio (when optional) to
be played.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
Table 14: SURR SETUP Menu Features
AUDIO Menu
SURR SETUP Menu
The VM9020TS has a built-in Pink Noise generator to help
set the relative speaker levels for multi-channel audio
playback.
Setting
Options
Function
LR (Left Rear) /
RR (Right Rear)
Large
Use when rear speakers have
good bass output.
Table 13: AUDIO Menu Features
Small
None
Use when rear speakers do not
have good bass output.
Setting
Options
Function
Use when rear speakers are not
present.
Pink
Noise
Off
Stop output of pink noise
Left channel pink noise
SUB (Subwoofer) Present
None
Use when subwoofer is present.
Left
Use when subwoofer is not
present.
Center
Right
Left Surr
Right Surr
Subwoofer
Off
Center channel pink noise
Right channel pink noise
Left surround channel pink noise
Right surround channel pink noise
Subwoofer pink noise
CTR (Center)
Large
Small
None
Use when center speaker has
good bass output.
Use when center speaker does
not have good bass output.
Use when center speaker is not
present.
DRC
Employ the Dynamic Range Control for
better playback for low volumes.
On
To change speaker settings for 2-channel mode, use the
BACK
Return to previous menu.
or
buttons (14, 22) on the remote control or the or
CNTR
CTRL
5ms
Adjust the time difference between the
center and front speakers to create a
time delay between 1 and 5 millisec-
onds, producing a more accurate audio
effect.
buttons (6, 7) on the joystick to select “DownMix”. To change
speaker settings for 6-channel mode, select “Full 6CH”. After
selecting 2 or 6-channel mode, use the
remote control or the button on the joystick (7) to move to
the speaker settings on the right.
SURROUND FX
4ms
3ms
Table 15: SURROUND FX Menu Features
button (19) on
2ms
Setting
Options
Function
1ms
Decode Mode
Off
Play original audio format.
0ms
Speaker Selection
Surround I Use Surround I decoding method.
Surround I Play mono output with surround
REAR
CTRL
15ms
12ms
9ms
Adjust the time difference between the
rear and front speakers to create a
time delay between 3 and 15 millisec-
onds, producing a more accurate audio
effect.
Selecting LARGE for the multi-channel speaker option will
give a full range output. Selecting SMALL for the multi-
channel speaker option will activate a high pass filter whose
crossover is dependent upon the sub-woofer low pass filter
frequency. For example, if the subwoofer low pass filter is set
to 80Hz, then the high pass SMALL speaker crossover will be
set to 90Hz.
Matrix
effect.
Surround I Enhance movie surround effects.
Movie
6ms
Surround I Play surround music effects.
Music
3ms
0ms
Panorama
On
Extend the video from the front to
the rear to achieve a better sur-
round effect.
(Only available
when Surround I
Music Mode is
activated.)
Down
Sampling
Off
Normal Output
Low pass
80Hz
High pass
90Hz
on
Audio signal output at 48kHz
Return to previous menu.
Off
0-6
Panorama is turned off.
BACK
120Hz
160Hz
135Hz
Dimension Ctrl
Shift audio output between front
and rear speakers.
180Hz
Refer to Table 14 when selecting speaker options for each
mode.
Center Width Ctrl 0-6
BACK
Shift audio output between front
and center channel speakers.
NOTE: When Down Sampling is ON, the audio output
signal will be converted to 48kHz. When Down Sampling
is OFF, the original sampling frequency is preserved.
Return to previous menu.
Table 14: SURR SETUP Menu Features
Setting
Options
Function
NOTE: Surround I is recommended when the playback
source is LPCM (Linear Pulse Code Modulation) or 2-
channel down mixed digital bit-stream.
FL (Front Left) /
FR (Front Right)
Large
Use when front speakers have
good bass output.
Small
Use when speakers do not have
good bass output.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
NOTE: When Surround I Music mode is selected,
Dimension Control and Center Width are available for
fine tuning to achieve a more realistic surround sound
processing.
RATING (Parental Lock) Menu
The DVD system has a built-in parental lock feature to
prevent unauthorized persons from viewing restricted disc
content. By default, the rating system is unlocked. Once
setup, the parental lock is released only by entering the
correct password. Once the password is entered, rating is
available for setup.
Table 16: RATING Menu Features
Setting
Options
Function
Password
_ _ _ _
Enter a 4-digit password to acti-
vate the “Rating” feature.
Rating
1. Kid Safe
2. G
Select the appropriate rating level
for the intended audience.
You may override higher ratings
by using your password.
3. PG
4. PG-13
5. PG-R
6. R
7. NC-17
8. Adult
Reset
Load Factory
BACK
Select “Reset” to restore the fac-
tory default settings for the Rating
system only.
Return to previous menu.
To reset the password, access the “RATING” menu and enter
the current password. Once the correct password is entered,
you can access the “Password” field and enter a new one.
NOTE: Record the password and keep it in a safe place
for future reference. The rating for each disc is marked
on the disc, disc packing, or documentation. If the rating
is not available on the disc, the parental lock feature is
unavailable. Some discs restrict only portions of the disc
and the appropriate content will play. For details, please
refer to the disc description.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
CD/MP3/WMA OPERATION
Instructions for Insert/Eject, Play/Pause, Stopping Playback,
Track Selection, Fast Forward/Fast Reverse, Scan, and
6. Current time
7. Disc Title
8. Track Title
9. Touch to return to MAIN MENU
Table 17: MP3/WMA Playback Modes
Play Mode Playback Details
Random Play are the same for DVD, CD and MP3 operation.
Please see the DVD Player Operation section for information
about these topics.
Disc Normal
Playback all files on the disc
and stop at the end.
10.
11.
12.
13.
: Touch to play/pause disc playback
: Touch to stop disc playback
: Touch to move to previous track
: Touch to move to next track
Disc Repeat
Random
Repeat playback of all files on
the disc.
NOTE: CD-R and CD-RW will not play unless the
recording session is closed.
Randomly play all files and stop
at the end.
14.
15.
: Touch to rewind current track
: Touch to fast forward current track
Single Track
Repeat Track
Play a specific file and stop.
The file naming formats listed below are compatible with this
unit:
Repeat playback of a specific
file.
16. Front Zone Playing Mode
17. Rear Zone Playing Mode
18. Encoding method of media being played.
19. "Surround Music" effect selected.
•
•
•
ISO 9660 – file name: 12 characters, file extension: 3
characters
ISO 9660 – file name: 31 characters, file extension: 3
characters
Joliet – 64 characters
Folder Normal
Folder Repeat
Play all files in a folder and stop
at the end.
Repeat playback of all files in a
folder/directory.
MP3/WMA Discs
This player allows you to playback MP3 files recorded on CD-
ROM, CD-R, and CD-RW. For CD-RW discs, please make
sure it is formatted using the full method and not the quick
method to prevent illegal disc operation.
4. Press the
button (14) on the remote control to
If the file or folder name does not conform to ISO 9660 file
system standards, it may not be displayed or played back
correctly.
confirm the playback mode then press the button (18)
to begin playback.
Use the following settings when compressing audio data for
your MP3 disc:
CD Player User Interface
The on-screen indicators and touch key areas for CD
playback are outlined below.
•
•
Transfer Bit Rate: 320kbps
Sampling Frequency: 48kHz
When recording MP3 up to the maximum disc capacity,
disable additional writing. For recording on an empty disc up
to maximum disc capacity, use the "Disc at once" setting.
Playing MP3/WMA Files
After inserting a MP3/WMA disc, files will play in the
sequence of the “Root’ directory.
Use the numeric keypad (29) on the remote control to access
files directly.
Selecting a Playback Mode
1. Press the /BAND button (20) on the remote control to
stop disc play.
2. Press the
button (19) on the remote control or the
button on the joystick (9) to enter playback mode (PLAY
MOD).
3. Press the
,
, or
buttons (18, 17, 19) on the
remote control, or the or button (8, 9) on the
joystick to choose from the following playback options:
1. Current track and total number of tracks on disc
2. Elapsed playing time
3. Touch to activate/deactivate Repeat play mode
4. Touch to activate/deactivate Scan mode
5. Touch to activate/deactivate Random mode
20
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
SD CARD READER OPERATION
Accessing SD Card Mode
Moving Through Chapters
To switch to SD card mode, press the SD button (19) on the
front panel.
Press the
button (19) on the remote control or the
button on the joystick (17) to advance to the next chapter.
Using the Touch-Screen Controls
The touch keys for SD card playback are described below.
Press the button (17) on the remote control or the
button on the joystick (16) to move to the previous chapter.
Change Directory
Touch the ( [DIR+] / [DIR-] ) key on the screen to navigate
through the Directories / Folders
Previous/Next Page
Touch the ( [PAGE+] / [PAGE-] ) key on the screen to
navigate through Pages / Files.
Direct Chapter / Track Selection
During DVD, VCD and CD
playback, you can use the numeric
keypad on the remote control (29)
to access a track directly.
•
•
•
•
•
•
: Play/Pause playback
: Stop playback
PAGE -: View previous page
PAGE +: View next page
DIR -: View previous directory
DIR +: View next directory
NOTE: Media (SD Card / CD-R / DVD) with a ROOT
directory containing only music, movie or JPEG files
may cause the RANDOM / REPEAT function to work
incorrectly. To ensure the proper playback of music,
movie, and JPEG files, place all media files inside folders
on the data storage media.
Controlling Playback
Stopping Playback
Touch the stop button ( ) on the screen or press the
/
BAND button (20) on the remote control to stop playback.
Pausing Playback
Touch the play/pause button (
) on the screen, press the
button on the remote control (18), or press the joystick
button (5) on the front panel to suspend or resume playback.
Repeat Playback
Press the REPT button (7) on the remote control or touch
“Repeat” on the screen to alter repeat mode according to the
following: Repeat Single, Repeat Folder, Repeat Off
Random Playback
Press the RDM button (33) on the remote control or touch
“Random” on the screen to activate random playback and
play all tracks in random order.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
TV TUNER OPERATION
•
Press the
button (22) on remote control or the
Accessing TV Mode
button (7) on the joystick to tune to the next stored
station.
To switch to TV mode, press the TV button (16) on the front
panel or press the SRC button (8) on the remote control until
TV appears at the bottom of the screen.
Direct Channel Selection
Use the numeric keypad on the
remote control (29) to enter a
specific TV station.
NOTE: Touch the top left corner to access the MAIN
MENU Multi-ZONE SETUP menu and the top right corner
to access the Multi-ZONE menu (rear zone setup).
Display Current Channel
Press the DISP button (10) on the
remote control to display
information regarding the current
TV station.
Auto Tuning
Press the
button (19) on remote control, or the button
on the joystick (9) to seek the next available TV station by
increasing the tuning frequency.
Press the
button (17) on the remote control, or the
button on the joystick (8) to seek the next available TV station
by decreasing the tuning frequency.
Press the /BAND,
,
,
or button to stop
searching.
Once a TV station is searched, the auto seeking stops and
the TV station is played. If no station is searched, the tuning
stops at the first channel after performing a round search.
Manual Tuning
Press and hold the or buttons (8, 9) on the joystick to
increase or decrease the TV frequency one step.
Storing Stations (AS)
Automatic Preset Memory
To select the strong stations in the current TV frequency
range, press and hold the joystick button (5) to activate the
Auto Store function. The new stations replace stations
already stored. Press the joystick button again or press the
/BAND button (20) on the remote control to stop searching.
Using Preset Scan
To scan stored stations:
1. Press the joystick button (5) to scan all stored TV sta-
tions. The unit pauses for 10 seconds at each station.
2. Press the joystick button again or press the /BAND
button (20) on the remote control to stop scanning and
play the current station.
Selecting a TV Station
To browse through stored stations:
•
Press the
button (15) on the remote control or the
button (6) on the joystick to tune to the previous stored
station.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
TROUBLESHOOTING
Table 18: Troubleshooting
Problem
Cause
Corrective Action
GENERAL
Unit will not power on
Radio Fuse blown
Car battery fuse blown
Illegal operation
Install new fuse with correct rating
Install new fuse with correct rating
Press the RESET button located in the bottom right corner of the front panel
Replace battery with new one
Remote control does not function
No/low audio output
Battery depleted
Battery installed incorrectly
Improper audio output connection
Volume set too low
Remove battery and install correctly
Check wiring and correct
Increase volume level
Improper “MUTE” connection
Speakers damaged
Review wiring diagram and check “MUTE” connection
Replace speakers
Heavily biased volume balance
Speaker wiring is in contact with metal part of car
Pirated disc is in use
Adjust the channel balance to the center position
Insulate all speaker wiring connections
Use original copy
Poor sound quality or distortion
Speaker power rating not compatible with unit
Speaker is shorted
Connect proper speakers
Check speaker contact
Tel-Mute malfunction
“MUTE” wire is grounded
Check that “MUTE” connection is not grounded and that it’s properly insulated
Unit resets itself when engine is off
Incorrect connection between ACC and positive battery Check wiring and correct
wire
TFT MONITOR
Monitor does not open automatically
No image
TFT Auto Open is turned off
Turn TFT Auto Open on
Incorrect connection to parking brake wire
PRK SW is activated and parking brake is not engaged
DVD is not compatible with current TV system settings
Improper video signal connections
Check wiring and correct
Stop vehicle in safe place and apply parking brake
Change setup to accommodate disc
Check wiring and correct
Flashing image or interference appears on screen
Prolonged image or improper height/width ratio dis- Improper aspect ratio setup
play
Use correct aspect ratio setting
Monitor stops at incorrect position
TUNER
Moving path is blocked
Press OPEN key to restart monitor movement
Weak station searching
Auto antenna is not fully extended
Auto antenna not properly connected
LOCAL function is activated
Disc already inside unit
Connect the auto antenna control cable properly
Connect the auto antenna control cable properly
Turn LOCAL function off
Cannot insert disc
Eject current disc and insert new one
Use disc in good condition
Disc does not play back
Disc is warped or scratched
Disc is dirty or wet
Clean disc with soft cloth
Laser pickup is dirty
Clean laser pickup with cleaning disc
Use compatible disc
Incompatible disc is used
Disc rating exceeds Parental Lock rating limit
Disc region code is not compatible with unit
Disc is inserted upside down
Change Parental Lock settings to lower restriction
Use disc with proper region code
Insert disc with label side up
23
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
Table 18: Troubleshooting
Problem
Cause
Corrective Action
Image blurred, distorted, or dark
PBC cannot be used during VCD playback
No repeat or searching while playing VCD
MP3
Disc is illegally copied
Use original disc
Turn PCB off
PCB is not available on the disc
PCB is on
Interruption occurred during playback
Disc is dirty or scratched
Clean disc or replace
File is damaged/bad recording
Message is longer than LCD can display
Recreate disc with good files
Incorrect playback message displayed
Error Messages
Table 19: Error Messages
Message Displayed
Cause
Corrective Action
Loading
No Disc
Disc is being read
Disc is dirty
Clean disc with soft cloth
Disc is upside down
Insert disc with label side up
Insert disc
Disc not present in loading compartment
Disc is dirty
Bad Disc
Clean disc with soft cloth
Insert disc with label side up
Disc is upside down
Unknown disc
Region Error
Error
Disc format is not compatible with this unit
DVD is not compatible with region code of unit
illegal mechanism operation
Press EJECT key for 5 seconds to reset loading mechanism
7. When the vehicle warms up during cold weather or
Care and Maintenance
under damp conditions, condensation may appear on
the LCD panel. Should this occur, the screen will not
operate properly until the moisture has evaporated.
8. We suggest you use a cleaning disc in this unit more
frequently than in the unit in your home due to the
environmental conditions of the vehicle.
1. Use only a clean silicone cloth and neutral detergent to
clean the front panel or monitor. A rough cloth and non-
neutral detergent (such as alcohol) may result in
scratching or discoloration.
2. Do not get water or cleaning fluids on the unit.
3. If the temperature inside the player gets too hot, a
protective circuit automatically stops play of the disc. If
this occurs, allow the unit to cool before operating the
player again.
4. Never insert anything other than a 5” (12 cm) compact
disc into the player as the mechanism can be damaged
by foreign objects.
5. Do not attempt to use a 3” (8 cm) CD-Single disc in this
unit, either with or without an adaptor, as damage to the
player and/or disc may occur. Such damage is not
covered by the Warranty on this product.
6. The CD player may not operate properly in extreme hot
or cold. If such conditions occur, allow the interior of the
vehicle to reach a normal temperature before using
player.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
SPECIFICATIONS
Video
Format: NTSC, PAL (auto-detection)
Output: 1Vp-p (75-ohm), buffered
Input: 1Vp-p (75-ohm)
FM Tuner
Tuning Range: 87.5MHz - 107.9MHz
Mono Sensitivity (-30dB): 9dBf
Quieting Sensitivity (-50dB): 15dBf
Alternate Channel Selectivity: 70dB
Signal to Noise Ratio @ 1kHz: 58dB
Image Rejection: 80dB
Stereo Separation @ 1kHz: 30dB
Frequency Response: 30Hz - 15kHz, -3dB
AM Tuner
Tuning Range: 530kHz - 1710kHz
Sensitivity (-20dB): 30uV
Signal to Noise Ratio @ 1kHz: 50dB
Image Rejection: 60dB
Frequency Response: 50Hz - 2kHz, -3dB
Monitor
CEA Power Ratings
Main Amplifier
Power Output: 18 watts RMS X 4 channels into 4-ohms @ <
1% THD+N
Signal to Noise Ratio: 70dBA below reference. (Reference: 1
watt, 4-ohms)
Dynamic Power: 88 watts into 4-ohms, all channels driven
Frequency Response: 20Hz to 20kHz, -3dB. Aux input used
as source reference
Reference Supply Voltage: 14.4VDC
Center Amplifier
Power Output: 22 watts RMS X 1 channels into 4-ohms @ <
1% THD+N
Signal to Noise Ratio: 70dBA below reference. (Reference: 1
watt, 4-ohms)
Dynamic Power: 25 watts into 4-ohms, all channels driven
Frequency Response: 20Hz to 20kHz, -3dB
Reference Supply Voltage: 14.4VDC
DVD/CD Player
Compatible formats: DVD-R, DVD-RW, DVD+R, DVD+RW,
CD-R, CD-RW, CD-DA, MP3, WMA, HDCD, SVCD, VCD,
MPEG, JPEG, MP3/WMA files burned onto a DVD+R/W or
DVD-R/W and Kodak Picture CD
Screen Size: 6.5" (Measured diagonally), 16:9 Widescreen
•
6.1" (155mm) W X 3.51" (89.2mm) H
Screen Type: TFT Liquid Crystal Display (LCD), active matrix
Brightness: 400 cd/m2
Contrast Ratio: 350
Response Time: 15mS rise time, 25mS fall time
Resolution:
•
280, 800 sub pixels, 1200 (W) X 234 (H)
Viewing angle:
•
•
•
65 degrees left or right
40 degrees up
65 degrees down
Anti-glare screen
General
Auxiliary Input impedance: 10k
Power Supply: 11 to 16VDC, negative ground
Fuse: 10-amp, mini ATM type
Double-DIN chassis dimensions: 7" X 7" X 4" (178mm x
178mm x 100mm)
Signal to Noise Ratio: 95dBA
Dynamic Range: >95dB
Frequency Response: 20Hz to 20kHz, -3dB
Channel Separation: > 60dB @ 1kHz
D/A Converter(s): 6-channel high performance 24-bit,
192kHz, multi-bit Sigma Delta modulation. DAC supports
sample rates from 8~192kHz.
** Specifications subject to change without notice.
Electronic Skip Protection (ESP): 16Mbit high-speed flash
memory
DVD: 2-3 sec, CD-DA: 10 sec, MP3: 100 sec, WMA: 200 sec
(ESP time is approximate)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
VM9020TS
12-MONTH LIMITED WARRANTY
AUDIOVOX CORPORATION (the Company) warrants to the
original retail purchaser of this product that should this
product or any part thereof, under normal use and conditions,
be proven defective in material or workmanship within 12
months from the date of original purchase, such defect(s) will
be repaired or replaced with new or reconditioned product (at
the Company's option) without charge for parts and repair
labor. To obtain repair or replacement within the terms of this
Warranty, please contact Jensen at the telephone number
provided below.
This Warranty is in lieu of all other express warranties or
liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE
LIMITED TO THE DURATION OF THIS WRITTEN
WARRANTY. ANY ACTION FOR BREACH OF ANY
WARRANTY HEREUNDER INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABILITY MUST BE BROUGHT
WITHIN A PERIOD OF 12 MONTHS FROM DATE OF
ORIGINAL PURCHASE. IN NO CASE SHALL THE
COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY
OTHER WARRANTY, EXPRESS OR IMPLIED,
This Warranty does not extend to the elimination of car static
or motor noise, to correction of antenna problems, to costs
incurred for installation, removal, or reinstallation of the
product, or damage to tapes, compact discs, accessories or
vehicle electrical systems. This Warranty does not apply to
any product or part thereof which, in the opinion of the
Company, has suffered or been damaged through alteration,
improper installation, mishandling, misuse, neglect, accident,
or by removal or defacement of the factory serial number/bar
code label(s) or markings. THE EXTENT OF THE
COMPANY'S LIABILITY UNDER THIS WARRANTY IS
LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED
ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S
LIABILITY EXCEED THE PURCHASE PRICE PAID BY
PURCHASER FOR THE PRODUCT.
WHATSOEVER. No person or representative is authorized to
assume for the Company any liability other than expressed
herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or
consequential damage so the above limitations or exclusions
may not apply to you. This Warranty gives you specific legal
rights and you may also have other rights which vary from
state to state.
U.S.A: 1-800-323-4815
CANADA: Call 1-800-323-4815 for location of warranty
station serving your area.
Audiovox Electronics Corporation
Hauppauge, NY 11788
Technical Assistance: 1-800-323-4815
© 2005 Audiovox
Ver 1.0
Printed in China
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|