JVC VCR SR V10E User Manual

ENGLISH

CONTENTS

SAFETY FIRST

Safety Precautions ..................................2

INDEX

INSTALLING YOUR NEW RECORDER

Basic Connections ...............................10

S-VIDEO Connection ...........................11

INITIAL SETTINGS

VIDEO CASSETTE RECORDER

Auto Set Up .........................................12

PLAYBACK

Basic Playback .....................................15

Playback Features ................................16

RECORDING

Basic Recording ...................................19

Recording Features ..............................20

B.E.S.T. Picture System .........................23

SERIES PLAYBACK AND RECORDING

Series Playback ....................................24

Series Recording ..................................26

TIMER RECORDING

SHOWVIEW Timer Programming .........28

Express Timer Programming .................30

24 Hour Express Timer Programming ...32

Automatic Satellite Programme

Recording ............................................35

PROGRAMME NAVIGATION

Navigation ...........................................36

EDITING

Edit From A Camcorder ........................40

Edit To Or From Another

Video Recorder ....................................41

SYSTEM CONNECTIONS

Connecting To A Satellite Receiver ......42

Connecting/Using A Stereo System ......43

SUBSIDIARY SETTINGS

Mode Set .............................................44

SHOWVIEW System Setup ....................49

Tuner Set .............................................50

Clock Set .............................................56

Video Channel Set ...............................58

TROUBLESHOOTING

QUESTIONS AND ANSWERS

SPECIFICATIONS

LIST OF TERMS

LPT0720-001A

Download from Www.Somanuals.com. All Manuals Search And Download.

For Italy:

“It is declared that this product, brand JVC, conforms to the Ministry Decree n. 548 of 28 Aug.’95

published in the Official Gazette of the Italian Republic n. 301 of 28 Dec.’95”

The STANDBY/ON ¹button does not completely shut off mains power from the unit, but switches

operating current on and off. “`” shows electrical power standby and “^!” shows ON.

Video tapes recorded with this video recorder in the LP/EP (Long Play/Extended Play) mode cannot be

played back on a single-speed video recorder.

When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to

allow for ventilation (10 cm or more on both sides, on top and at the rear.)

When discarding batteries, environmental problems must be considered and the local rules or laws

governing the disposal of these batteries must be followed strictly.

Failure to heed the following precautions may result in damage to the recorder, remote control or video

cassette.

1. DO NOT place the recorder ...

... in an environment prone to extreme temperatures or humidity.

... in direct sunlight.

... in a dusty environment.

... in an environment where strong magnetic fields are generated.

... on a surface that is unstable or subject to vibration.

2. DO NOT block the recorder’s ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able

to get out.)

3. DO NOT place heavy objects on the recorder or remote control.

4. DO NOT place anything which might spill on top of the recorder or remote control.

(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

5. DO NOT expose the apparatus to dripping or splashing.

6. DO NOT use this equipment in a bathroom or places with water. Also DO NOT place any containers

filled with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups, etc.) on top

of this unit.

7. DO NOT place any naked flame sources, such as lighted candles, on the apparatus.

8. AVOID violent shocks to the recorder during transport.

MOISTURE CONDENSATION

Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or

under extremely humid conditions—just as water droplets form in the surface of a glass filled with cold

liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where

condensation may occur, keep the recorder turned on for a few hours to let the moisture dry.

ATTENTION:

To mobile phone users:

Using a mobile phone in the vicinity of the recorder may cause picture vibration on the TV screen or

change the screen to a blue back display.

On placing the recorder:

Some TVs or other appliances generates strong magnetic fields. Do not place such appliance on top of

the recorder as it may cause picture disturbance.

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX

FRONT VIEW

A STANDBY/ON ¹Button ੬ pg. 12

B Cassette Loading Slot

C 24H EXPRESS ^#Button ੬ pg. 32

D S-VIDEO/VIDEO/AUDIO Input Connectors

੬ pg. 40

E Stop/Eject ⁰Button ੬ pg. 15, 19

F S-VHS ET Button ੬ pg. 22

G Front Display Panel ੬ pg. 6

H Infrared Beam Receiving Window

I REC LINK Button ੬ pg. 35

J Record ⁷Button ੬ pg. 19

K Pause ⁹Button ੬ pg. 16

L Play ⁴Button ੬ pg. 15

M Advanced JOG Dial ੬ pg. 15, 32

Connector cover

Attach the provided connector cover when you do not

use the front panel connectors.

To attach it, insert the cover’s left tab to the recorder’s

front panel connector part, then push in the cover’s

right side.

To remove it, press the cover’s left side.

Download from Www.Somanuals.com. All Manuals Search And Download.

REAR VIEW

A Mains Power Cord ੬ pg. 10

G AUDIO/VIDEO IN Connectors

੬ pg. 24, 26, 35, 41, 42

H ANT. IN Connector ੬ pg. 10

B S VIDEO OUT Connector

੬ pg. 11, 24, 26, 41, 42

C S VIDEO IN Connector ੬ pg. 24, 26, 41, 42

D Lithium battery compartment ੬ See below

E REMOTE OUT Connector ੬ pg. 24, 26

F AUDIO/VIDEO OUT Connectors

੬ pg. 10, 24, 26, 41, 42, 43

I REMOTE IN Connector* ੬ pg. 24, 26

* For the Remote Control Unit RM-G30 (not provided)

J RF OUT Connector ੬ pg. 10

Installing/Removing the lithium battery

Be sure to connect the power plug to an main outlet first before installing the lithium battery; otherwise, the battery’s

service life will be drastically shortened.

A Make sure that the power plug is connected to an

main outlet and turn off the recorder power.

B Open the battery cover while pressing the release tab

as illustrated.

C Insert a lithium battery with the plus (+) side up and

push it in.

● To remove the lithium battery, press the latch

downward

using a pointed non-metallic object, then pull out the

lithium battery.

D Close the battery cover until it clicks in place.

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX (cont.)

FRONT DISPLAY PANEL

A Instant REVIEW Indicator ੬ pg. 17

B Start Time Indicator ( ) ੬ pg. 17, 20, 30, 32

C S-VHS Indicator ੬ pg. 22, 47

D Stop Time Indicator ( ) ੬ pg. 17, 20, 30, 32

E Channel/Clock/Remain Display

Mode Display (L-1, F-1, S-1 or S-2)

F “Timer” Indicator ੬ pg. 29, 31, 32

G Automatic Satellite Programme Recording

Indicator ( ) ੬ pg. 35

H Play Indicator

I Record Indicator

J Counter Display

(The counter can display up to +/ – “19:59:59”. If

the playback or recording time exceeds this limit

the display starts to count from “0:00:00”.)

K Tape Speed SP/LP/EP ੬ pg. 19

Download from Www.Somanuals.com. All Manuals Search And Download.

ON-SCREEN DISPLAY

When “O.S.D. (PLAY)” is set to “ON” (੬ pg. 46), various operational indicators appear on the TV screen if you press

(OK). (They also appear for 5 seconds when the playback starts.) Press

(OK) again to clear the indicators.

When “O.S.D. (REC)” is set to “ON” (੬ pg. 45), the operational indicators displayed on the TV screen will be recorded.

Set “O.S.D. (REC)” to “OFF” if you do not want to record these indicators.

A Operation Mode Indicators

B Tape Speed SP/LP/EP

I VPS/PDC Indicator ੬ pg. 29, 31

J Type of Broadcast ੬ pg. 22

K Channel Position Number and Station Name/

Auxiliary Input Indicator (L-1, F-1, S-1 or S-2)

L Current Day/Month/Year

M Clock Display

N Timer Warning Display

C Tape Direction

D Index MARK Indicator ੬ pg. 19

E Counter Display

F Tape Remaining Time Indicator ੬ pg. 21

G Audio Mode Display ੬ pg. 18

A warning appears on the TV screen to tell you that the

timer-recording is to start in 5 minutes if you’re not in the

Timer mode at that time. The warning blinks for the entire 5

minutes leading up to the start of timer recording. To clear

the display, press & on the remote control.

H Tape Position Indicator

The tape position indicator

appears on the TV screen

when you press 3 or

5 from the Stop mode

or perform an Index Search

(੬ pg. 17). The position of

“q” in relation to “0”

S-VHS ET Indicator

(S-VHS ET : ON/S-VHS ET : OFF) ੬ pg. 22, 47

O “Cassette Loaded” Mark

(beginning) or “+” (end)

shows you where you are

on the tape.

Beginning

End

NOTE:

Depending on the type of tape being used, the tape position

indicator may not appear correctly.

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX (cont.)

A TV Button ੬ “Operating JVC TVs” on page 9

B TV/VCR Button ੬ “Operating JVC TVs” on

page 9

REMOTE CONTROL

C REVIEW Button ੬ pg. 17

D Number Keys ੬ pg. 19, 28

E VPS/PDC Button ੬ pg. 29, 31

F Cancel ^&Button ੬ pg. 33

0000 Button ੬ pg. 21

G STOP +/– Button ੬ pg. 30

H START +/– Button ੬ pg. 30

I PROG Button ੬ pg. 28

J Programme Check ^"Button ੬ pg. 33

K Rewind ³Button ੬ pg. 15, 16

L Record ⁷Button ੬ pg. 19

M Stop ⁸Button ੬ pg. 15, 19

N MENU Button ੬ pg. 37

O ^{r t}Button ੬ pg. 12

TV PR +/– Button ੬ “Operating JVC TVs” on

page 9

P STANDBY/ON ¹Button ੬ pg. 12

Q AUDIO Button ੬ pg. 18

^ (TV Muting) Button ੬ “Operating JVC TVs”

on page 9

R Display – – : – – Button ੬ pg. 21

S DAILY Button ੬ pg. 29, 31

T WEEKLY Button ੬ pg. 29, 31

U AUX Button ੬ pg. 40

V Timer^#Button ੬ pg. 29, 31

W DATE +/– Button ੬ pg. 30

X PR +/– Button ੬ pg. 19

Y Auto Tracking ^pButton ੬ pg. 18

SP/LP/EP Button ੬ pg. 19

Z 30 SEC Button ੬ pg. 17

a Play ⁴Button ੬ pg. 15

b Fast Forward ⁵Button ੬ pg. 15, 16

c Pause ⁹Button ੬ pg. 16

d OK Button ੬ pg. 13

Information

Button*

* If you press this button when “O.S.D. (PLAY)” is set to “ON”

(੬ pg. 46), you can see the current recorder status on the TV

screen.

e ^{w e}Button ੬ pg. 16, 17

TV ^%+/– Button ੬ “Operating JVC TVs” on

page 9

Download from Www.Somanuals.com. All Manuals Search And Download.

Buttons with a small dot on the left side of the name can also be used to operate your JVC TV while holding down the TV button.

(੬ “Operating JVC TVs” below)

This remote control transmits A code signals only; it is not applicable to B code signals.

How To Use

The remote control can operate most of your video recorder’s functions, as well as basic functions of JVC TV sets. (੬ “Operating

JVC TVs” below)

● Point the remote control toward the receiving window.

● The maximum operating distance of the remote control is about 8 m.

Operating JVC TVs

To operate your TV, while holding down the TV button, press the corresponding button: 1, TV/VCR, TV PR +/–, TV ^%+/–,

^ (TV Muting).

NOTES:

● When inserting the batteries, be sure to insert in the correct directions as indicated under the battery cover.

● Depending on the type of JVC TV, some or all functions may not be operated using the remote control.

● If the remote control doesn’t work properly, remove its batteries, wait a short time, replace the batteries and then try again.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING YOUR NEW RECORDER

It’s essential that your video recorder be properly

connected.

Basic Connections

THESE STEPS MUST BE COMPLETED BEFORE ANY

VIDEO OPERATION CAN BE PERFORMED.

Aerial connector

Back of TV

A ^{Check the contents.}

Make sure the package contains all of the accessories

listed in “SPECIFICATIONS” on page 63.

B ^{Situate the recorder.}

RF cable

(provided)

Place the recorder on a stable, horizontal surface.

TV aerial

Audio/video input

cable

C ^{Connect the recorder to TV.}

connectors

The connection method you use depends on the type of

TV you have.

Audio/video cable

(provided)

RF Connection

8 To connect to a TV with NO audio/video input

connectors . . .

A Disconnect the TV aerial cable from the TV.

B Connect the TV aerial cable to the ANT. IN connector

on the rear panel of the recorder.

Mains power cord

ANT. IN

C Connect the provided RF cable between the RF OUT

connector on the rear panel of the recorder and the

TV’s aerial connector.

AV Connection

8 To connect to a TV with audio/video input

connectors . . .

Back of recorder

A Connect the aerial, recorder and TV as per “RF

AUDIO/VIDEO OUT RF OUT

Connection”.

Mains outlet

B Connect the provided audio/video cable between the

AUDIO/VIDEO OUT connectors on the rear panel of

the recorder and the TV’s audio/video input

connectors.

Make AV connection if your TV has audio/video input

connectors in order to reduce the possibility of

interference. With AV connection, you can enjoy

stereo playback of video tapes if you are using a stereo

TV.

D ^{Connect the recorder to mains.}

Plug the end of the mains power cord into a mains outlet.

NOTES:

● For switching the TV’s mode, refer to the instruction

manual of your television.

● To obtain high-quality S-VHS pictures, you can also use the

S-VIDEO connection described on page 11.

After the connection is completed, perform “Auto Set

Up” on page 12.

Download from Www.Somanuals.com. All Manuals Search And Download.

S-VIDEO Connection

AUDIO IN connectors

Back of TV

S-Video cable

(provided)

S-VIDEO IN

connector

Audio cable

(not provided)

TV aerial cable

Aerial connector

Mains outlet

Mains

power cord

S VIDEO OUT

Back of recorder

AUDIO OUT

RF cable (provided)

8 To connect to a TV with S-VIDEO/AUDIO IN

connectors . . .

NOTES:

● You can obtain high-quality S-VHS pictures.

● If your TV is not stereo-capable, use the recorder’s AUDIO

OUT connectors to connect to an audio amplifier for Hi-Fi

stereo sound reproduction. (੬ pg. 43)

● To operate the recorder with your TV using the S-VIDEO

connection, set your TV to its AV mode.

● For switching the TV’s mode, refer to the instruction manual of

your television.

A ^{Connect the recorder to TV.}

A Connect the aerial, recorder and TV as per “RF

Connection” (੬ pg. 10).

B Connect the recorder’s S VIDEO OUT connector to

the TV’s S-VIDEO IN connector.

C Connect the recorder’s AUDIO OUT connectors to the

TV’s AUDIO IN connectors.

After the connection is completed, perform “Auto Set

Up” on page 12.

B ^{Connect the recorder to mains.}

Plug the end of the mains power cord into a mains outlet.

Download from Www.Somanuals.com. All Manuals Search And Download.

INITIAL SETTINGS

Before starting, make sure of the following:

● The TV aerial cable should be connected to the recorder.

● The recorder’s mains power cord should be connected to a

mains outlet.

Auto Set Up

● The TV should be set to its AV mode (with AV or S-VIDEO

connection ੬ pg. 10, 11) or UHF channel 36 (with RF

connection ੬ pg. 10).

Auto Channel Set/Auto Clock Set/

Auto Guide Program Number Set

After the 1 button on the recorder or remote control is

pressed for the first time to power on the recorder, by simply

selecting your country, the Auto Set Up function sets the

tuner channels, clock* and Guide Program numbers

automatically.

A ^{Turn on the recorder.}

Set display appears on the TV screen.

Press 1 on the recorder or remote control. The Country

* If you live in Hungary (MAGYARORSZÁG), Czech Republic (CESKÁ

REPUBLIKA), Poland (POLSKA) or other countries in Eastern Europe

(OTHER EASTERN EUROPE), set the clock manually.

NOTE:

If you have connected your TV to

the recorder with RF connection

and the on-screen display

appearing on UHF channel 36

looks distorted, perform “Video

Channel Set” on page 58.

B ^{Select your country.}

Press rt to move the

highlight bar (pointer) to your

country’s name.

(Example) DEUTSCHLAND is

selected.

NOTES:

● If you have selected MAGYARORSZÁG, CESKÁ REPUBLIKA,

POLSKA or OTHER EASTERN EUROPE, press OK. The Clock

Set screen appears. Set the clock manually (੬ pg. 56), then

go to step 3.

● If you have selected any other country name, go to step 3.

Download from Www.Somanuals.com. All Manuals Search And Download.

ATTENTION

C ^{Perform Auto Set Up.}

Once you have performed Auto Set Up, even if the recorder’s

memory backup has expired, all the stored stations and their

Guide Program numbers remain in the recorder’s memory

and the recorder will not perform Auto Set Up again. You

only need to set the clock. (੬ pg. 56)

Press OK.

“Auto” blinks on the front display panel; do NOT press

any button on the recorder or remote control until the

front display panel shows either the display as

illustrated in step 4 or “– –:– –” as illustrated on

page 14.

If you have moved to a different area, perform each setting as

required.

● Video channel setting (for RF connection users) ੬ pg. 58

● Tuner setting ੬ pg. 50

● Clock setting ੬ pg. 56

If a new station starts broadcasting in your area, perform

tuner setting (੬ pg. 50) and, if necessary, video channel

setting (੬ pg. 58).

● If you are using the on-screen

display, the AUTO SET

screen will appear. As Auto

Set Up progresses, the “q”

mark on the TV screen

NOTES:

moves from left to right.

● In the area where no TV station transmits a PDC (Programme

Delivery Control) signal, the recorder can perform neither

Auto Clock Set nor Auto Guide Program Number Set.

● If there is a power cut, or if you press 1 or MENU while Auto

Set Up is in progress, Auto Set Up will be interrupted; be sure

to turn off the recorder power once and try again from step 1.

● Auto Clock Set may not function properly depending on the

reception condition.

Beginning

End

D ^{Confirm/Set video channel.}

● If no sound accompanies the picture or the audio sounds

unnatural on some channels that have been stored by Auto Set

Up, the TV system setting for those channels may be incorrect.

Select the appropriate TV system for those channels

(੬ pg. 53, “INFORMATION”).

With RF connection

The video channel that is

shown on the display panel is

your video channel. Press OK.

● If you have selected

MAGYARORSZÁG, CESKÁ

REPUBLIKA, POLSKA or

OTHER EASTERN EUROPE in

step 2 on page 12, “2” appears

instead of “1”.

● To view picture signals from the recorder, set your TV to the

video channel.

With AV or S-VIDEO

connection

Press PR – until the display

panel shows “1 – –” (or

“2 – –”). Now the video channel is set to off. Then press

OK.

● To view picture signals from the recorder, set your TV to its AV

mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

INITIAL SETTINGS (cont.)

Results of Auto Set Up appear on the front display panel

If both Auto Channel Set and Auto Clock Set have been performed successfully, the

correct current time is displayed.

Turn on the TV and select its video channel or AV mode, then make sure that all necessary stations

have been stored in the recorder’s memory by using the PR button(s).

● If station names (ID – ੬ pg. 55) have also been stored in the recorder’s memory, the station

name will be displayed at the upper left corner of the TV screen for about 5 seconds when the

recorder is tuned to a different station.

● If you want to set the tuner manually such as to add or skip channels, to change channel

positions, or to set or change station names, see pages 52 – 55.

If Auto Channel Set has succeeded but Auto Clock Set has not, “1” (channel position) is

displayed.

A Turn on the TV and select its video channel or AV mode, then make sure that all necessary

stations have been stored in the recorder’s memory by using the PR button(s).

● If station names (ID – ੬ pg. 55) have also been stored in the recorder’s memory, the station

name will be displayed at the upper left corner of the TV screen for about 5 seconds when the

recorder is tuned to a different station.

● If you want to set the tuner manually such as to add or skip channels, to change channel

positions, or to set or change station names, see pages 52 – 55.

B Perform “Clock Set” on page 56.

If both Auto Channel Set and Auto Clock Set have failed, “– –:– –” is displayed.

Make sure the cables are connected properly and turn off the recorder’s power once, then turn the

recorder’s power back on again.

The Country Set display appears on the TV screen; perform “Auto Set Up” on page 12 again.

IMPORTANT

● To check if the Guide Program numbers have been set correctly, perform the SHOWVIEW Timer Programming (੬ pg. 28).

● In certain reception conditions, station names may not be stored correctly, and auto Guide Program Number Set may not work

properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the SHOWVIEW

system, the recorder will record a TV programme of a different station. When programming the timer using the SHOWVIEW

system, be sure to check the desired channel is selected correctly (੬ pg. 28, “SHOWVIEW^®Timer Programming”).

● Your video recorder memorizes all detected stations even if reception of some of them is poor. You can delete those stations with

an unacceptable picture (੬ pg. 53, “Delete A Channel”).

INFORMATION

Just Clock

Your recorder is equipped with the Just Clock function which provides accurate time keeping through automatic adjustments at

regular intervals, by reading data from a PDC signal. If you want to take advantage of this function, simply set it to “ON”

(੬ pg. 56, “Just Clock”).

Last-Function Memory

When the power plug is removed from the recorder or when the power failure occurs, your settings for the following functions are

kept in memory if the lithium battery is not exhausted. These settings will resume when the recorder is turned on again.

● Input selection (channel or auxiliary input; L-1, F-1, S-1, or S-2)

● Country setting (੬ pg. 12)

● Recording tape speed (੬ pg. 19)

● Mode settings (੬ pg. 44 – 48)

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYBACK

A ^{Load a cassette.}

Basic Playback

Make sure the window side is up, the rear label side is

facing you and the arrow on the front of the cassette is

pointed toward the recorder.

Turn on the TV and select the video channel (or

AV mode).

● Do not apply too much pressure when inserting.

● The recorder will come on automatically.

● If the record safety tab has been removed and “REC SAFETY”

is set to “ON” (੬ pg. 48), playback begins automatically.

● If the record safety tab is intact, or if the record safety tab is

removed and “REC SAFETY” is set to “OFF” (੬ pg. 48), the

recorder checks the tape information for Programme

Navigation. For details, refer to “Navigation” (੬ pg. 36).

B ^{Find the programme start point.}

If the tape is advanced past the start point, press 3 or

turn the JOG dial to the left. To go forward, press 5 or

turn the JOG dial to the right.

C ^{Start playback.}

Press 4. “bESt” appears blinking in the recorder’s front

display panel during automatic tracking. (੬ pg. 23)

D ^{Stop playback.}

Press 8 on the remote control or 0 on the recorder’s

front panel. Then press 0 to remove the cassette.

Usable cassettes

● Compact VHS camcorder recordings can be played on this

video recorder. Simply place the recorded cassette into a

VHS Cassette Adapter and it can be used just like any

full-sized VHS cassette.

● This video recorder can record on regular VHS and Super

VHS cassettes. While only VHS signals can be recorded on

regular VHS cassettes*, both VHS and Super VHS signals

can be recorded and played back using Super VHS

cassettes.

* By using the S-VHS ET function, it is possible to record and

play back with S-VHS picture quality on VHS cassettes

with this recorder.

Playback Resume Function

If there is a power outage during normal playback, Repeat

Playback (੬ pg. 18) or Series Playback (੬ pg. 24), the

playback will resume automatically when the power is

restored to the recorder if the lithium battery is not

exhausted.

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYBACK (cont.)

Still Picture/Frame-By-Frame

Playback Features

Playback

1 Pause during playback.

Push the JOG dial.

Press 9.

2 Activate frame-by-frame playback.

Turn the JOG dial to the right for forward frame-by-frame

playback, or to the left for reverse frame-by-frame

playback.

Press 9.

Press w or e.

To resume normal playback, press 4 or push the JOG

dial.

Slow Motion

During playback, turn the JOG dial one click to the left

for forward slow motion. To play in reverse slow motion,

continue to turn the JOG dial to the left after selecting all

the forward direction slow motion modes.

During still picture, press and hold 9 for 2 seconds, then

release. Press 9 and release again to return to still

picture.

During still picture, press and hold w or e. Release to

return to still picture.

ATTENTION

● Picture may not appear during high-speed search with an

LP/EP-recorded tape.

NOTE:

During slow motion playback, some noise may appear on the TV

screen. Press PR + or – on the remote control to eliminate the

noises.

● Noise may appear or the picture may appear distorted with

an EP-recorded tape during still, slow motion,

frame-by-frame playback or variable speed search.

● In the high-speed search, still, slow motion or

frame-by-frame playback mode, the picture will be

distorted, and there will be a loss of colour.

High-Speed (Turbo) Search

●

When normal playback resumes from search, still, slow

motion or frame-by-frame playback, the picture may jitter

vertically momentarily depending on the type of TV being

used.

During playback, turn the JOG dial quickly to the left or

right.

During playback or still, press 5 for forward

high-speed search, or 3 for reverse high-speed search.

Clean the video heads using a dry cleaning

cassette — TCL-2 — when:

NOTE:

For short searches, press and hold 5 or 3 for over 2

seconds during playback or still picture. When released, normal

playback resumes.

● Rough, poor picture appears while a tape is played back.

● The picture is unclear or no picture appears.

● “USE CLEANING CASSETTE” appears on the screen (only

with “O.S.D. (PLAY)” set to “ON” (੬ pg. 46)).

To resume normal playback, press 4.

NOTE:

The heads get dirty in the following cases:

● in an environment prone to extreme temperature or

humidity

● in a dusty environment

● flaw, dirt or mold on video tapes

● continuous usage for a long time

Download from Www.Somanuals.com. All Manuals Search And Download.

Variable Speed Search

Skip Search

During playback, turn the JOG dial to the right for

forward variable-speed search, or to the left for reverse

variable-speed search.

During playback, press 30 SEC 1 to 4 times to skip over

unwanted sections.

Each press initiates a 30-second period of fast-motion

playback. Normal playback resumes automatically.

During playback, press w or e.

● The more times you press, the faster the playback picture

moves.

To resume normal playback during a Skip Search,

press 4.

● To decrease speed, press the button for the opposite direction.

NOTES:

● For speed search, refer to the table below.

● You can see smooth slow motion picture only during 1/2x

slow motion playback.

● You can hear the normal audio track only during 1.5x speed

search.

Instant ReView

Simply by pressing a single button, the recorder power comes

on, rewinds, and begins playback of the last timer-recorded

programme. If you have several programmes recorded, you can

easily access any of them.

Forward

Reverse

NOTE:

Reverse

slow

motion

Slow

motion

Reverse

Normal

play

Forward

Reverse

play

Before starting, make sure that the recorder is off and that the

Timer mode is disengaged.

–1

–7, –5, –3

–1/6, –1/18 1/18, 1/6, 1/2*

1.5*,2, 3, 5, 7

Activate Instant ReView.

* PAL SP/LP only

Press REVIEW. The recorder power comes on and the

recorder searches for the index code indicating the start

of the last timer-recorded programme. Once it’s found,

playback begins automatically.

To resume normal playback, press 4.

● The front display panel tells you how many programmes have

been timer-recorded. If you have, for example, 3 programmes,

the Instant REVIEW indicator (

the first of the 3 programmes, press REVIEW three times. The

recorder searches and begins playback automatically. You can

access a programme as far as 9 index codes away from the

current tape position.

● The number of recorded programmes will not be displayed on

the front display panel after Auto Satellite Programme

Recording (੬ pg. 35).

) and “3” blink. To watch

Index Search

Your recorder automatically marks

index codes at the beginning of

each recording. This function gives

you quick access to any one of 9

index codes in either direction.

NOTE:

Before starting, make sure the

recorder is in the Stop mode.

Mode Lock

Activate Index Search.

— To prohibit any operations during

playback

Press w or e (2 or 6). “2 1” or “6 1” is

displayed on the TV screen and search begins in the

corresponding direction.

Press and hold OK on the remote control for more than

● To access index codes 2 through 9, press w or e repeatedly

until the correct index number is displayed.

Example:

To locate the beginning of B from the current position, press w

twice.

To locate the beginning of D from the current position, press e

once.

5 seconds. “

” and “ ” light up on the front display

panel. No buttons will function and playback will not be

interrupted until the recording end (unrecorded portion)

or tape end is reached (੬ pg. 48).

To cancel Mode Lock, press and hold OK again for more

than 5 seconds.

● When OK is pressed to set Mode Lock, the on-screen display

appears and the time counter remains on the TV screen. If the

time counter is not necessary, set “O.S.D. (PLAY)” and “O.S.D.

(REC)” to “OFF” (੬ pg. 45, 46).

Current position

NOTE:

It is also possible to use Mode lock during Repeat Playback

(੬ pg. 18) and Series Playback (੬ pg. 24).

Index number

● When the specified index code is located, playback begins

automatically.

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYBACK (cont.)

Next Function Memory

Manual Tracking

The Next Function Memory “tells” the recorder what to do after

rewinding. Before continuing, make sure the recorder is in the

Stop mode.

Your recorder is equipped with automatic tracking control.

During playback, you can override this and adjust the tracking

manually by pressing the PR buttons.

a- For Automatic Start Of Playback

Press 3, then press 4 within 2 seconds.

b- For Automatic Power Off

Press 3, then press 1 within 2 seconds.

c- For Automatic Timer Standby

1 Override automatic tracking.

Press 3, then press # (TIMER) within 2 seconds.

During playback, press p on the remote control.

NOTE:

2 Adjust the tracking manually.

The Automatic Power Off does not work if “AUTO TIMER” is set

to “ON” (੬ pg. 45) and if any timer programming has been

made. The recorder directly goes into the Timer-Standby mode

after rewinding a tape.

Press PR + or – on the remote control.

● Press p again to return to automatic tracking.

NOTE:

When a new tape is inserted, the recorder enters the automatic

tracking mode automatically.

Repeat Playback

Your recorder can automatically play back the whole tape

repeatedly.

Soundtrack Selection

Your recorder is capable of recording three soundtracks (HI-FI L,

HI-FI R and NORM) and will play back the one you select.

During Playback

1 Start playback.

Press 4.

Pressing AUDIO changes the soundtrack as follows:

2 Activate Repeat Playback.

Press 4 and hold for over 5 seconds, then release.

TRACK

● The Play indicator ($) on the front display panel blinks slowly.

USE

On-Screen Display

3 Stop Repeat Playback.

Press 8 at any time.

HI FI

L j h R

● Pressing 4, 3, 5 or 9 also stops Repeat Playback.

For Hi-Fi stereo tapes

NOTES:

HI FI

L j

● Repeat playback is not possible with a cassette recorded in EP

mode.

For main audio of Bilingual tapes

● To select the returning point (recording end or tape end), see

“RETURN POINT” (੬ pg. 48).

● It is possible to use the Mode Lock function. (੬ pg. 17)

HI FI

h R

For sub audio of Bilingual tapes

NORM

For audio-dubbed tapes

HI FI

NORM

NOTES:

● “HI FI L j h R” should normally be selected. In this mode,

Hi-Fi stereo tapes are played back in stereo, and the normal

audio track is played back automatically for tapes with only

normal audio.

● For instructions on recording stereo and bilingual

programmes, refer to page 22.

● “O.S.D. (PLAY)” must be set to “ON”, or the on-screen

displays will not appear (੬ pg. 46).

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

A ^{Load a cassette.}

Basic Recording

Insert a cassette with the record safety tab intact. If the tab

has been removed, set “REC SAFETY” to “OFF”

(੬ pg. 48).

Turn on the TV and select the video channel (or

AV mode).

● The recorder checks the tape information for Programme

Navigation. For details, refer to “Navigation” (੬ pg. 36).

B ^{Choose a programme.}

Press PR +/– or the number keys. Or push the JOG dial

and turn it to the left or right to select the channel you

wish to record.

C ^{Set the tape speed.}

Press SP/LP/EP (p). The current setting appears on the

front display panel or TV screen. Press SP/LP/EP (p)

again to change the setting while the tape speed is

displayed on the TV screen.

● In EP mode, the recording time is extended three times.

● If you record a programme in EP mode on this recorder, it is

recommended to play back the EP-recorded tape on this

recorder.

● It is not possible to select EP mode if “COLOUR SYSTEM” is

set to “MESECAM”. (੬ pg. 48)

D ^{Start recording.}

Press and hold 7 and press 4 on the remote control, or

press 7 on the recorder.

● If “O.S.D. (REC)” is set to “ON” (੬ pg. 45), “MARK” blinks on

the screen while an index code is being marked.

B.E.S.T. takes place at the beginning of both the first SP and

the first LP (or EP) recording after inserting the cassette.

(੬ pg. 23)

E ^{Pause/Resume recording.}

Press 9. Press 4 to resume recording.

● You can select channel during the Record Pause mode.

F ^{Stop recording.}

Press 8 on the remote control or 0 on the recorder.

Then press 0 to remove the cassette.

ATTENTION

● When “O.S.D. (REC)” is set to “ON” (੬ pg. 45), the

operational indicators displayed on the TV screen will be

recorded. Set “O.S.D. (REC)” to “OFF” if you do not want

to record these indicators.

● You cannot access the Main Menu screen during

recording.

Recording Resume Function

If there is a power outage during recording, Repeat

Recording (੬ pg. 21), Series Recording (੬ pg. 26), or timer

recording (੬ pg. 28, 30, 32), the recording will resume

automatically when power is restored to the recorder if the

lithium battery is not exhausted.

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING (cont.)

Record One Programme While

Recording Features

Watching Another

Once recording is in progress, all you need to do is to set

the channel controls on the TV for the station you wish to

view.

● The programme selected with the TV’s channel controls

appears on the TV screen, while the one selected with the

recorder’s PR buttons is recorded on the tape.

Mode Lock

— To prohibit any operations during

recording

Press and hold OK on the remote control for more than

5 seconds. “

” and “ ” light up on the front display

panel. No buttons will function and recording will not be

interrupted until the recording ends.

To cancel Mode Lock, press and hold OK again for more

than 5 seconds.

● When OK is pressed to set Mode Lock, the on-screen display

appears and the time counter remains on the TV screen. If the

time counter is not necessary, set “O.S.D. (PLAY)” and “O.S.D.

(REC)” to “OFF” (੬ pg. 45, 46).

NOTE:

It is also possible to use Mode lock during Repeat Recording

(੬ pg. 21) and Series Recording (੬ pg. 26).

Accidental erasure prevention

To prevent accidental recording on a recorded cassette,

remove its safety tab. To record on it later, cover the hole

with adhesive tape, or set “REC SAFETY” to “OFF”

(੬ pg. 48).

Record safety tab

Download from Www.Somanuals.com. All Manuals Search And Download.

Elapsed Recording Time Indication

Repeat Recording

You can record programmes on one tape repeatedly.

1 Set the counter display.

Press – –:– – until a counter reading appears on the front

1 Start recording.

display panel.

Press and hold 7 and press 4 on the remote control, or

● The front display panel shows

the counter reading with “:”

lit.

press 7 on the recorder.

2 Activate Repeat Recording.

Press and hold 7 and press 4 on the remote control, or

press 7 on the recorder for over 5 seconds.

● The Record indicator (⅜) on the front display panel blinks

slowly.

2 Reset the counter.

Press 0000 before starting recording or playback.

● The counter is reset to “0:00:00” and shows the exact elapsed

time as the tape runs. You can check the exact time of a

recording or playback.

3 Stop Repeat Recording.

Press 8 on the remote control or 0 on the recorder at

any time.

Tape Remaining Time

● Pressing 9 also stops Repeat Recording.

Press – –:– – until the time remaining on the tape appears.

● The front display panel shows

NOTES:

● Recording will be performed in LP mode even if the tape

speed is set to EP mode when you start recording.

the tape remaining time with

“:” blinking.

● By pressing the – –:– – button,

you can change display to

● It is possible to use the Mode Lock function (੬ pg. 20).

show the channel position*, clock time, counter reading or

tape remaining time.

* Channel position is not displayed during playback.

NOTE:

Depending on the type of tape being used, the tape remaining

time reading may not appear right away, or is not correct.

“– –:– –” may sometimes appear, or the display may blink on

occasion.

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING (cont.)

Super VHS ET (S-VHS ET)

Receiving Stereo and Bilingual

Programmes

— Recording on VHS cassettes with

S-VHS quality

Your recorder is equipped with a Sound-Multiplex decoder (A2)

and a Digital stereo sound decoder (NICAM) making reception

of stereo and bilingual broadcasts possible.

When the channel is changed, the type of broadcast being

received will be displayed on the TV screen for a few seconds.

You can record in SP mode on VHS cassettes with S-VHS picture

quality. You can play back a tape recorded using the S-VHS ET

function on most of S-VHS recorders and of VHS recorders

equipped with SQPB (S-VHS QUASI PLAYBACK) function.

(Notice some recorders are not compatible with the S-VHS ET

function.)

Type of Broadcast Being

On-screen Display

Received

● You can activate the S-VHS ET function only before you start

recording on a VHS cassette.

● Before recording, make sure that “B.E.S.T.” is set to “ON”.

(੬ pg. 45)

A2 Stereo

A2 Bilingual

BIL.

Regular Monaural

NICAM Stereo

NICAM Bilingual

NICAM Monaural

(none)

ST NICAM

BIL. NICAM

NICAM

Engage the S-VHS ET mode.

Press S-VHS ET on the recorder. You can check the

current setting (“S-VHS ET : ON” or “S-VHS ET : OFF”). If

“S-VHS ET : OFF” appears on the TV screen, press S-VHS

ET again in about 5 seconds to set it to “ON”.

● To listen to a stereo programme, press AUDIO on the remote

control until “HIFI L j h R” appears on the TV screen.

● To listen to a bilingual programme, press AUDIO on the

remote control until “HIFI L j” or “HIFI h R” appears on the

TV screen.

● To listen to the standard (Regular Monaural) audio while

receiving a NICAM broadcast, press AUDIO on the remote

control until “NORM” appears on the TV screen.

● The S-VHS indicator lights up on the front display panel.

NOTES:

● You cannot activate the S-VHS ET function ...

... while recording is in progress.

... while timer-recording (੬ pg. 28, 30, 32) is in progress.

... while B.E.S.T. (੬ pg. 23) is in progress.

NOTE:

● The S-VHS ET function does not work ...

“O.S.D. (PLAY)” must be set to “ON”, or the on-screen displays

will not appear (੬ pg. 46).

... with S-VHS cassettes.

... with recordings in LP/EP mode.

● To keep the highest quality recording and playback pictures

over a long period of time, S-VHS recording on S-VHS

cassettes is recommended.

When you change the setting in stop mode, set “O.S.D. (REC)” to

“ON” (੬ pg. 45) first. Then set “O.S.D. (REC)” to “OFF” if you

do not want to record the operational indicators displayed on

the TV screen.

● Use of high grade tapes is recommended for S-VHS ET

recordings. On some tapes, picture quality will not improve

even if the S-VHS ET function is used. Check the recording

quality before you start important recordings.

● While playing back a tape recorded using the S-VHS ET

function on some recorders, noise may appear. (If playback

picture becomes blurred or interrupted, use a cleaning

cassette.)

● In the high-speed search, still, slow-motion or frame-by-frame

playback modes (੬ pg. 16), noise may appear. If these modes

are performed frequently on a tape recorded using the

S-VHS ET function, the tape may be damaged and the picture

may be deteriorated.

To Record Stereo and Bilingual Programmes (A2)

Stereo programmes are automatically recorded in stereo on the

Hi-Fi audio track (with the normal audio track recording mixed L

and R channel sound).

● Bilingual programmes are automatically recorded in bilingual

on the Hi-Fi audio track. The main soundtrack will be

recorded on the normal audio track.

To Record NICAM Stereo and Bilingual

Programmes

The NICAM audio programme will be recorded on the Hi-Fi

audio track, and the standard audio programme will be recorded

on the normal audio track.

NOTES:

● If the quality of stereo sound being received is poor, the

broadcast will be received in monaural with better quality.

● Before playing back a programme recorded in stereo, or a

bilingual programme, refer to “Soundtrack Selection” on

page 18.

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording

B.E.S.T. Picture

System

The recorder assesses the quality of the tape once you

initiate recording.

DURING B.E.S.T.

The B.E.S.T. (Biconditional Equalised Signal Tracking)

system checks the condition of the tape in use during

playback and recording, and compensates to provide the

highest-possible playback and recording pictures. You

can set “B.E.S.T.” to “ON” or “OFF” to your preference

(੬ pg. 45).

B.E.S.T. COMPLETE

● The recorder spends approximately 7 seconds assessing the

condition of the tape, then begins recording.

Playback

NOTES:

● The B.E.S.T. system works for both SP and LP (or EP) modes

only after a tape has been inserted and the Record mode is first

initiated. It does not work during recording.

The recorder assesses the quality of the tape once you

initiate playback.

● The B.E.S.T. system does not work while Automatic Satellite

Programme Recording is in progress (੬ pg. 35).

● In the case of timer recordings, the B.E.S.T. system works

before recording is initiated.

● Once the cassette is ejected, the B.E.S.T. data is cancelled. The

next time the cassette is used for recording, B.E.S.T. is

re-performed.

● The recorder adjusts the playback picture quality based on the

quality of the tape in use.

● B.E.S.T. is active during automatic tracking. “bESt” appears

blinking on the recorder’s front display panel.

NOTES:

● When watching a tape recorded with “B.E.S.T.” set to “ON”, it

is recommended that you leave B.E.S.T. on during playback as

well.

ATTENTION

Since the B.E.S.T. system works before recording actually

starts, there is a delay of approximately 7 seconds after 7

and 4 on the remote control are pressed, or 7 on the

recorder is pressed. To make sure you record the desired

scene or programme in its entirety, first perform the following

steps:

● When watching a rental tape or one recorded on another

video recorder, or when using this recorder as the player for

editing, set B.E.S.T. to your preference (੬ pg. 45).

● “bESt” only appears at the beginning of automatic tracking.

Even though it doesn’t appear after that, the B.E.S.T. function is

operative.

A Press and hold 9 and press 7 to engage the Record

Pause mode.

● The recorder then automatically checks the condition of

the tape and, after approximately 7 seconds, re-enters

Record Pause mode.

B Press 4 to start recording.

If you want to bypass the B.E.S.T. system and begin recording

immediately, set “B.E.S.T.” to “OFF” (੬ pg. 45).

Download from Www.Somanuals.com. All Manuals Search And Download.

SERIES PLAYBACK AND RECORDING

Series Playback

REMOTE OUT

Mini-plug cable

(not provided)

SR-V10E-1

REMOTE IN

S VIDEO OUT

Mini-plug cable

AUDIO/

VIDEO OUT

S-video cable

(provided)

(not provided)

Audio/video cable

(provided)

S VIDEO IN

REMOTE OUT AUDIO/VIDEO OUT

SR-V10E-2

S VIDEO OUT

S-video cable (not provided)

AUDIO/VIDEO IN

REMOTE IN

Audio/video cable (not provided)

To S-video input

connectors

To Audio/video input

connectors

NOTE:

Series Playback is also possible with the front AUDIO/VIDEO or

AUDIO/S-VIDEO input connectors.

Download from Www.Somanuals.com. All Manuals Search And Download.

E ^{Start playback.}

Press 4 on either of SR-V10E.

● When the playback reaches to the returning point (tape end or

recording end (੬ pg. 48)), the other SR-V10E successively

starts playback. (The cassette will automatically be rewound

when the playback stops.) Therefore, the cassettes loaded on

two SR-V10E will be played back alternately as many times as

you want.

F ^{Stop playback.}

Press 0 on the SR-V10E which is playing back a

cassette.

Using two sets of SR-V10E, you can play back two cassettes

alternately as many times as you want. You can select the

returning point for Series Playback.

NOTES:

● If you do not want to display the operational indicators on the

TV screen during playback, set “O.S.D. (PLAY)“ and “O.S.D.

(REC)“ to “OFF“ (੬ pg. 45, 46).

NOTE:

● If there is a power outage during Series Playback, the playback

will resume automatically when the power is restored to the

recorder if the lithium battery is not exhausted.

Use the buttons and controls on the recorder for the Series

Playback operations (except when using Mode Lock

(੬ pg. 17)).

● It is possible to use the Mode Lock function (੬ pg. 17).

A ^{Make connections.}

Connect two sets of SR-V10E and a TV using AV cables as

illustrated on page 24.

● The mini-plug cable is a mono 3.5 mm mini-plug to mono 3.5

mm mini-plug connector.

● When playing back S-VHS recordings, it is recommended to

use the S-VIDEO connection to obtain the high quality

pictures.

B ^{Turn on all components.}

After completing the connections, turn on all the

components.

● Set your TV to the VIDEO or AV mode. Refer to the TV

instruction manual.

C ^{Set the input mode on the SR-V10E-2.}

Turn the JOG dial to the right or left on the SR-V10E-2 to

select the appropriate input mode depending on the

connectors being used.

“L-1”: for the rear AUDIO/VIDEO IN connectors

“F-1”: for the front AUDIO/VIDEO input connectors

“S-1”: for the rear AUDIO/S VIDEO IN connectors

“S-2”: for the front AUDIO/S-VIDEO input connectors

D ^{Load cassettes.}

Insert the playback cassette into each SR-V10E.

Download from Www.Somanuals.com. All Manuals Search And Download.

SERIES PLAYBACK AND RECORDING (cont.)

Series Recording

Camcorder

Another recorder

To S-video

output

To Audio/video output

connectors

Audio/video cable

(not provided)

S-video cable

(not provided)

AUDIO/VIDEO OUT

REMOTE OUT

SR-V10E-1

REMOTE IN

AUDIO/VIDEO IN

S VIDEO OUT S VIDEO IN

Mini-plug cable

(not provided)

S-video cable

(provided)

Mini-plug cable

(not provided)

Audio/video cable (provided)

AUDIO/VIDEO OUT

S VIDEO IN

REMOTE OUT

SR-V10E-2

S VIDEO OUT

AUDIO/VIDEO IN

REMOTE IN

To S-video input connectors

S-video cable (not provided)

Audio/video cable (not provided)

To Audio/video input connectors

NOTE:

Series Recording is also possible with the front AUDIO/VIDEO

or AUDIO/S-VIDEO input connectors.

Download from Www.Somanuals.com. All Manuals Search And Download.

E ^{Start recording.}

Press 7 on either of SR-V10E.

● When the tape remaining time reaches to 2 minutes during

recording, the other SR-V10E successively starts recording.

(The cassette will automatically be rewound when the

recording stops.*) Therefore, recording will be continued onto

cassettes loaded on two SR-V10E alternately.

* Replace the cassette after rewound if you want to continue to record

onto another cassette.

F ^{Stop recording.}

Press 0 on the SR-V10E which is recording.

Using two sets of SR-V10E, a long recording will be possible

(such as camcorder recording, another recorder playback or TV

broadcast).

NOTES:

● When recording a TV broadcast, select in the same channel

on both SR-V10E.

● If the playback source device has a superimpose/OSD disable

feature, set its superimpose or display feature to “OFF“.

● If you do not want to record the operational indicators

displayed on the TV screen during recording, set “O.S.D.

(PLAY)“ and “O.S.D. (REC)“ to “OFF“ (੬ pg. 45, 46).

● If there is a power outage during Series Recording, the

recording will resume automatically when the power is

restored to the recorder if the lithium battery is not exhausted.

● It is possible to use the Mode Lock function (੬ pg. 20).

NOTE:

Use the buttons and controls on the recorder for the Series

Recording operations (except when using Mode Lock

(੬ pg. 20)).

A ^{Make connections.}

Connect two sets of SR-V10E to other device, antenna or

cable as illustrated on page 26.

● The mini-plug cable is a mono 3.5 mm mini-plug to mono 3.5

mm mini-plug connector.

● When connecting a camcorder or another recorder with an

S-VIDEO output connector as recording deck, it is

recommended to use the S-VIDEO connection to obtain the

high quality pictures.

B ^{Turn on all components.}

After completing the connections, turn on all the

components.

● Set your TV to the VIDEO or AV mode. Refer to the TV

instruction manual.

C ^{Set the input mode on both SR-V10E.}

Turn the JOG dial to the right or left on each SR-V10E to

select the appropriate input mode depending on the

connectors being used.

“L-1”: for the rear AUDIO/VIDEO IN connectors

“F-1”: for the front AUDIO/VIDEO input connectors

“S-1”: for the rear AUDIO/S VIDEO IN connectors

“S-2”: for the front AUDIO/S-VIDEO input connectors

D ^{Prepare for recording.}

Insert the recording cassette into each SR-V10E and

prepare the playback source device.

Download from Www.Somanuals.com. All Manuals Search And Download.

TIMER RECORDING

With the SHOWVIEW system, timer programming is greatly

simplified because each TV programme has a corresponding

code number which your recorder is able to recognize.

SHOWVIEW^®Timer

A ^{Access the SHOWVIEW screen.}

Programming

Press PROG.

Before performing the SHOWVIEW Timer

Programming:

● Make sure that the recorder’s built-in clock is set properly.

● Insert a cassette with the safety tab in place. If the tab has

been removed, set “REC SAFETY” to “OFF” (੬ pg. 48).

The recorder will come on automatically.

● Turn on the TV and select the video channel (or AV mode).

The front display panel looks like this:

ATTENTION

It is impossible to perform timer programming during

recording.

B ^{Enter the SHOWVIEW number.}

Press the number keys to

enter the SHOWVIEW number

of a programme you wish to

record.

● If you make a mistake, press &

and input the correct number.

The SHOWVIEW number you enter appears on the front display

panel with only a 4-digit number:

C ^{Access the SHOWVIEW Program screen.}

Press OK and the SHOWVIEW

Program screen appears (if

you’re just starting out, “P1”

appears).

The front display panel shows the programme number. Pressing

" changes the display to the programme start time, the stop

time, the date, the tape speed then the channel position.

IMPORTANT

Make sure the channel position number you wish to record is

displayed; if not, see “SHOWVIEW^®System Setup” on page 49

and set the Guide Program number correctly.

● If the number you entered is invalid, “ERROR” appears on the

TV screen and “Err” appears on the front display panel. Press

& and input a valid SHOWVIEW number.

● If the “GUIDE PROG SET” screen appears, see “ATTENTION”

on page 29.

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES:

D ^{Set the tape speed.}

● To Change The Stop Time . . .

. . . press STOP +/– after pressing OK in step 3. You can

compensate for anticipated programme schedule delays.

● To Timer-Record Weekly Or Daily Serials . . .

Press SP/LP/EP (p).

. . . after pressing OK in step 3, press WEEKLY (number key

“9”) for weekly serials or DAILY (number key “8”) for daily

serials (Sunday — Saturday). Either “WEEKLY” or “DAILY”

appears on the TV screen. Pressing the button again makes the

corresponding indication disappear.

● It is not possible to select EP mode if “COLOUR SYSTEM” is

set to “MESECAM”. (੬ pg. 48)

● You can programme this recorder to timer-record as many as 8

programmes. If you try to programme the recorder to record a

ninth, “PROGRAM FULL” appears on the TV screen and

“FULL” appears on the front display panel. To record the extra

programme, you must first cancel any unnecessary

programmes (੬ pg. 33).

E ^{Set the VPS/PDC mode.}

“OFF”.

● If “VPS/PDC ON” is displayed on the TV screen, VPS/PDC is

set to ON.

● If “VPS/PDC OFF” is displayed on the TV screen, VPS/PDC is

set to OFF.

੬ “VPS/PDC Recording” on page 31.

Press VPS/PDC (number key “7”) to select “ON” or

● Even if a power failure occurs, the recorder keeps your timer

programmes if the lithium battery is not exhausted.

Satellite Receiver Users

To timer-record a satellite broadcast using the SHOWVIEW

system:

A Set the Guide Program numbers for all satellite broadcasts

received on your satellite receiver. (੬ pg. 49)

B Perform steps 1 – 9.

C Set the satellite receiver to the appropriate channel before

the selected programme begins.

D Leave the satellite receiver’s power on.

F ^{Access the Title Edit screen.}

Press the number key “1”.

The Title Edit screen appears.

● You can access the Title Edit

screen only when “PROG.

NAVIGATION” is set to “ON”.

(੬ pg. 46)

ATTENTION

Guide Program Number Set

“GUIDE PROG SET” appears after performing step 3 if the

Guide Program number for the SHOWVIEW number you

entered has not been set.

G ^{Enter the programme title.}

● Press the number keys or rt to input the channel

position number on which your recorder receives that

station, then press OK or e to set the Guide Program

number. The SHOWVIEW Program screen appears.

(Example)

Press the number keys and e

to enter characters, then

press OK. For details, refer to

“Entering Character” on

page 39.

To timer-record a ZDF

programme with the

SHOWVIEW system.

* If your recorder receives ZDF on

the channel position 2, press OK

or e after entering “2”.

H ^{Return to the normal screen.}

Press PROG or OK. “PROGRAM COMPLETED” appears

on the TV screen for about 5 seconds, then the normal

screen appears. If “PROGRAM OVERLAPPED” appears

on the TV screen and “Err” on the front display panel, see

page 34.

● Repeat steps 1 – 8 for each additional programme.

I ^{Engage the recorder’s timer mode.}

Press # (TIMER). The recorder turns off automatically and

“#” appears on the front display panel.

● To disengage the timer mode, press # (TIMER) again.

Download from Www.Somanuals.com. All Manuals Search And Download.

TIMER RECORDING (cont.)

If you do not know the SHOWVIEW number for the programme

you wish to record, use the following procedure to set your

recorder to timer-record the programme.

Express Timer

Programming

Example: To timer-record the programme from 21:00 to

22:00 on 25th December, on channel 1.

A ^{Access the SHOWVIEW screen.}

Before performing Express Timer Programming:

● Make sure that the recorder’s built-in clock is set properly.

● Insert a cassette with the safety tab in place. If the tab has

been removed, set “REC SAFETY” to “OFF” (੬ pg. 48).

The recorder will come on automatically.

Press PROG.

B ^{Access the Programme screen.}

● Turn on the TV and select the video channel (or AV mode).

Press START+/–. (If you’re

just starting out, “P1”

appears.)

ATTENTION

It is impossible to perform timer programming during

recording.

The front display panel looks like this:

C ^{Enter the programme start time.}

Press START+/– to enter the

time you want recording to

start.

● Press and hold START+/– to

move in 30-minute

increments, or press and

release repeatedly to move 1

minute at a time.

The front display panel looks like this:

D ^{Enter the programme stop time.}

Press STOP+/– to enter the time you want recording to

stop.

● Press and hold STOP+/– to move in 30-minute increments, or

press and release repeatedly to move 1 minute at a time.

E ^{Enter the programme date.}

Press DATE+/–.

● The current date appears on the TV screen. The date you enter

appears in its place.

Download from Www.Somanuals.com. All Manuals Search And Download.

F ^{Enter the channel position.}

L ^{Engage the recorder’s timer mode.}

Press PR+/–.

Press # (TIMER). The recorder turns off automatically and

“#” appears on the front display panel.

● To disengage the timer mode, press # (TIMER) again.

To Timer-Record Weekly Or Daily Serials . . .

. . . anytime during steps 2 through 8, press WEEKLY (number

key “9”) for weekly serials or DAILY (number key “8”) for daily

serials (Sunday – Saturday). Either “WEEKLY” or “DAILY” appears

on the TV screen. Pressing the button again makes the

corresponding indication disappear.

NOTES:

● You can programme this recorder to timer-record as many as 8

programmes. If you try to programme the recorder to record a

ninth, “PROGRAM FULL” appears on the TV screen and

“FULL” appears on the front display panel. To record the extra

programme, you must first cancel any unnecessary

programmes (੬ pg. 33).

G ^{Set the tape speed.}

Press SP/LP/EP (p).

● Even if a power failure occurs, the recorder keeps your timer

programmes if the lithium battery is not exhausted.

● It is not possible to select EP mode if “COLOUR SYSTEM” is

set to “MESECAM”. (੬ pg. 48)

Satellite Receiver Users

To timer-record a satellite broadcast using Express Timer

Programming:

A Perform steps 1 – 12. Enter “L-1” or “S-1” for the channel

position in step 6.

B Set the satellite receiver to the appropriate channel before

the selected programme begins.

C Leave the satellite receiver’s power on.

H ^{Set the VPS/PDC mode.}

Press VPS/PDC (number key “7”) to select “ON” or “OFF”.

● If “VPS/PDC ON” is displayed on the TV screen, VPS/PDC is

set to ON.

● If “VPS/PDC OFF” is displayed on the TV screen, VPS/PDC is

set to OFF.

੬ “VPS/PDC Recording” in the right column

VPS/PDC Recording

Now available from some TV stations, PDC (Programme

Delivery Control) and VPS (Video Programme System) are

service designed to assure safe, accurate timer recording.

With this system, special code signals are transmitted

together with the audio/video signals. These code signals

control your video recorder and have precedence over the

advertised times you may have preset into the timer. This

means that your recorder will start and stop recording when

the preset TV programmes actually start and end — even if

the broadcast time of a preset TV programme is changed.

I ^{Access the Title Edit screen.}

Press the number key “1”.

The Title Edit screen appears.

● You can access the Title Edit

screen only when “PROG.

NAVIGATION” is set to “ON”.

(੬ pg. 46)

NOTES:

● When you use Express Timer Programming, set the start

time (VPS or PDC time) exactly as advertised in the TV

listing. A different time than advertised will result in no

recording.

● VPS/PDC recording is also possible when a satellite

receiver or a cable system is connected to the AUDIO/

VIDEO IN connectors on your recorder.

J ^{Enter the programme title.}

Press the number keys and e

to enter characters, then

press OK. For details, refer to

“Entering Character” on

page 39.

How to check if the station being received transmits a

VPS/PDC signal

A Press – –:– – until the channel position appears on the

front display panel.

B Hold down START+ for about 5 seconds.

“VPS/PDC” appears blinking on the TV screen.

If a VPS/PDC signal is detected from the station,

“VPS/PDC” will stop blinking.

If no VPS/PDC signal is detected from the station,

“VPS/PDC” will blink at a slower rate.

C Press – –:– – or START+ again to return to normal display.

K ^{Return to the normal screen.}

Press PROG or OK. “PROGRAM COMPLETED” appears

on the TV screen for about 5 seconds, then the normal

screen appears. If “PROGRAM OVERLAPPED” appears

on the TV screen and “Err” on the front display panel, see

page 34.

● Repeat steps 1 – 11 for each additional programme.

Download from Www.Somanuals.com. All Manuals Search And Download.

TIMER RECORDING (cont.)

You can programme a timer recording that starts within 24 hours

using the JOG dial on the recorder.

24 Hour Express

A ^{Enter the programme mode.}

Press 24H EXPRESS # on the recorder. The start time

Timer Programming

indicator (

) starts blinking on the front display panel.

Before performing the 24 Hour Express Timer

Programming:

● Make sure that the recorder’s built-in clock is set properly.

● Insert a cassette with the safety tab in place. If the tab has

been removed, set “REC SAFETY” to “OFF” (੬ pg. 48).

The recorder will come on automatically.

Set the programme start/stop time and

channel.

Turn the JOG dial to the left or right to set the time you

want recording to start.

● One click stop of the JOG dial changes the time in 5-minute

intervals.

Push the JOG dial. The stop time indicator ( ) starts

blinking on the front display panel. Turn the JOG dial to

the left or right to set the time you want recording to stop.

Push the JOG dial. Turn the JOG dial to the left or right to

select the channel you wish to record.

● You can cancel the setting at any time by pressing and holding

the JOG dial for more than 3 seconds or pressing & on the

remote control. Repeat the step 2.

● To set the tape speed, press SP/LP/EP (p). The current

setting for the tape speed appears on the display panel for

about 5 seconds. Press SP/LP/EP (p) again to change the

setting while tape speed is displayed.

C ^{Engage the recorder’s timer mode.}

NOTES:

● You can programme this recorder to timer-record as many as

8 programmes. If you try to programme the recorder to record

a ninth, “FULL” appears on the front display panel. To record

the extra programme, you must first cancel any unnecessary

programmes (੬ pg. 33).

Press 24H EXPRESS #. The recorder turns off

automatically and ”#” appears on the front display

panel.

● To disengage the timer mode, press # (TIMER) or

24H EXPRESS # again.

● If “Err” appears on the front display panel, repeat the above

steps again.

● When a menu screen is shown, you cannot use 24 Hour

Express Timer Programming function. Press MENU to return to

normal screen, and try again.

● You can use 24 Hour Express Timer Programming function

also when the recorder is turned off.

● For 24 Hour Express Timer Programming function, the

programme overlap warning display does not appear even if

some programmes overlap each other. The programme with

the lower programme number will be recorded and the other

one will not be recorded correctly.

● Even if a power failure occurs, the recorder keeps your timer

programmes if the lithium battery is not exhausted.

Download from Www.Somanuals.com. All Manuals Search And Download.

To cancel or change a programme...

D ^{Cancel or change a programme.}

Press & to cancel a programme. To change programme

settings, press the appropriate button: START+/–,

STOP+/–, DATE+/–, PR+/–, VPS/PDC (number key “7”),

DAILY (number key “8”), WEEKLY (number key “9”) and/

or SP/LP/EP (p).

● If you do not want to edit the programme title, skip steps 5 and

E ^{Access the Title Edit screen.}

Press the number key “1”.

The Title Edit screen appears.

● You can access the title edit

screen only when “PROG.

NAVIGATION” is set to “ON”.

(੬ pg. 46)

Check, cancel and change programmes

F ^{Enter the programme title.}

Press the number keys and e

to enter characters, then

press OK. For details, refer to

“Entering Character” on

page 39.

A ^{Disengage the timer mode.}

Press # (TIMER), then press 1.

B ^{Access the Programme Check screen/display.}

Press ".

G ^{Return to the normal screen/display.}

Press " as many times as necessary. If there are still

some programmes remaining, go on to step 8.

H ^{Return to the timer mode.}

Press # (TIMER).

NOTE:

You can also check the programmes on the front display panel

even if the recorder’s power is off (unless the recorder is in the

Power Save mode ੬ pg. 47); however, it is not possible to

cancel or change the programmes.

C ^{Access the Programme screen/display.}

Press " again to check

more information. Each time

you press ", the next

programme’s information

appears.

The front display panel shows the programme number. Pressing

OK changes the display to the programme start time, the stop

time, the date, the tape speed then the channel position.

Download from Www.Somanuals.com. All Manuals Search And Download.

TIMER RECORDING (cont.)

When programmes overlap each other

If “PROGRAM OVERLAPPED” appears, you have another

programme overlapping the programme you have just made.

The Programme Check screen appears and conflicting

programmes will start blinking.

Example: Programme 1 (you have just made) and

Programme 4 overlap each other.

A ^{Confirm the overlapping programmes.}

Overlapping programmes blink on the TV screen.

B ^{Select the programme to modify.}

Press rt, then press OK or e.

● You can only select one of the overlapping programmes.

NOTE:

If you do not mind this overlap, press PROG to finish the timer

programme setting. The programme with the lower programme

number will be recorded and the other one will not be recorded

correctly. If no changes are made for approximately 1 minute,

the recorder will return to the normal screen.

C ^{Cancel or change programme setting.}

To cancel a programme, press & when the Programme

screen you do not want is shown. “PROGRAM

COMPLETED” appears on the TV screen for about 5

seconds, then the normal screen appears.

To change a programme, press the appropriate button:

START+/–, STOP+/–, DATE+/–, PR+/–, VPS/PDC

(number key “7”), DAILY (number key “8”), WEEKLY

(number key “9”) and/or SP/LP/EP (p) when the

Programme screen on which you want to make changes

is shown, then press OK. “PROGRAM COMPLETED”

appears on the TV screen for about 5 seconds, then the

normal screen appears.

NOTE:

If the overlap is not yet solved, or another overlap occurs with

the timer programme setting after making the last correction on a

programme, the conflicting programmes will be shown on the

Programme Check screen again. Repeat the above steps again

until the overlap is solved.

Download from Www.Somanuals.com. All Manuals Search And Download.

ATTENTION

● Be sure not to turn on the satellite receiver before the

Automatic Satellite

Programme

programme is executed; otherwise, the recorder will start

recording when the satellite receiver’s power is turned on.

● It is not possible to perform Automatic Satellite Programme

Recording via S VIDEO IN connector. (੬ pg. 42)

● Automatic Satellite Programme Recording and

timer-recording cannot be done at the same time.

Recording

Before performing the following steps:

● Make sure the satellite receiver is connected to the recorder’s

AUDIO/VIDEO IN connectors. (੬ pg. 42)

● Programme the timer on the satellite receiver.

● Insert a cassette with the safety tab in place. If the tab has

been removed, set “REC SAFETY” to “OFF” (੬ pg. 48).

This function allows you to automatically record a

satellite programme which is timer-programmed on your

external satellite receiver. Connect a satellite receiver to

the recorder’s AUDIO/VIDEO IN connectors and

programme the timer on the satellite receiver. The

recorder starts or stops recording by the signals input

from the satellite receiver. After recording, the recorder’s

power shuts off automatically.

A ^{Set the tape speed.}

Press SP/LP/EP (p).

● It is not possible to select EP mode if “COLOUR SYSTEM” is

set to “MESECAM”. (੬ pg. 48)

Engage the Automatic Satellite Programme

Recording mode.

Press and hold REC LINK for about 2 seconds. The “

indicator lights up and the recorder turns off

automatically.

“

“indicator

NOTES:

● To disengage the Automatic Satellite Programme Recording mode, press REC LINK. The “ “ indicator goes off.

● If the recorder’s power is off, it is not possible to engage the Automatic Satellite Programme Recording mode.

● In step 2, if the “ “ indicator does not light but instead blinks quickly even though your satellite receiver’s power is off, Automatic

Satellite Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Express Timer

Programming” (੬ pg. 30) to timer-record a satellite programme.

* Some satellite receivers output signals even if the power is off. Automatic Satellite Programme Recording is not possible with those satellite receivers.

● The “ “ indicator blinks while Automatic Satellite Programme Recording is in progress.

● For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

● Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer.

● Pressing the recorder’s 1 button while Automatic Satellite Programme Recording is in progress turns off the recorder’s power and

disengages the Automatic Satellite Programme Recording mode.

● If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Recording, it is not possible

to set different tape speeds for each programme.

● Depending on the type of satellite receiver, the recorder may not record a slight portion of the beginning of the programme or may

record slightly longer than the actual length of the programme.

● If you engage the Automatic Satellite Programme Recording mode when the satellite receiver’s power is on, the recorder will not

start Automatic Satellite Programme Recording even though the “ “ indicator blinks. When the satellite receiver shuts off once and

is turned back on again, the recorder starts recording.

● You can also record a programme from your cable system in the same way if the system has a timer.

● The B.E.S.T. system (੬ pg. 23) does not work while Automatic Satellite Programme Recording is in progress.

● Just Clock (੬ pg. 56) does not work when the Automatic Satellite Programme Recording mode is engaged.

● When the Automatic Satellite Programme Recording mode is engaged, or the recorder’s power is turned off after Automatic Satellite

Programme Recording is finished, the recorder will not enter the Timer mode even though “AUTO TIMER” is set to “ON”

(੬ pg. 45).

Download from Www.Somanuals.com. All Manuals Search And Download.

PROGRAMME NAVIGATION

Turn on the TV and select the video channel (or

AV mode).

Navigation

When you record a TV programme with this recorder, the

recorder automatically stores in its memory the recording date,

start time and station name. You can store these information for

up to 8 programmes on one cassette. At maximum, information

for 10 tapes can be stored. You can also enter the programme

title when performing “SHOWVIEW^®Timer Programming”

(੬ pg. 28) or “Express Timer Programming” (੬ pg. 30). It is

possible to store these information only when “PROG.

NAVIGATION” is set to “ON” (default setting) (੬ pg. 46).

When inserting a cassette with the record safety tab

intact, or when inserting a cassette with a record

safety tab removed and “REC SAFETY” is set to

“OFF” (੬ pg. 48)...

The recorder checks the

tape information for the

Programme Navigation.

If the recorder can store the

information for 3 or less tapes,

“REMAIN[ _]” also appears on

the TV screen.

If the recorder has already

stored the information for

10 tapes, “MEMORY

FULL” appears.

If you perform new recording,

the oldest tape information

will be deleted from the

recorder’s memory.

If the recorder cannot

detect the tape

information, “NO TAPE

DATA DETECTED”

appears.

NOTES:

● If you press any button while “CHECKING TAPE DATA”

appears on the TV screen, the operation is canceled.

● Even if the recorder has already stored the information for

8 programmes on one cassette, no message appears. If you

perform new recording, the oldest information will be

deleted from the recorder’s memory.

When inserting a cassette whose record safety tab

has been removed and “REC SAFETY “ is set to “ON”

(੬ pg. 48) ...

Playback begins automatically.

You can use Navigation Playback (੬ pg. 37), but you cannot

edit programme title or delete tape data (੬ pg. 38, 39).

Download from Www.Somanuals.com. All Manuals Search And Download.

Navigation Playback

Programme Navigation Screen

This function is useful when you wish to quickly find out what

programmes you have recorded on a tape with this recorder. This

function allows you to select a programme to watch, and then

automatically searches for the start of the programme.

A ^{Load a recorded cassette.}

Insert a cassette recorded on this recorder.

B ^{Access the Main Menu screen.}

Press MENU.

C ^{Access the Programme Navigation screen.}

Press rt to move the

highlight bar (pointer) to

“PROGRAMME

A Recording date

B Recording start time*

C Station name*

NAVIGATION”, then press

OK or e.

● If “NO TAPE DATA

DETECTED” appears on the TV

screen, you cannot use the

Navigation Playback function.

* After entering the programme title (੬ pg. 38), programme title

appears instead of the recording start time and station name.

D Currently selected programme

E Programme title*

* Before entering the programme title (੬ pg. 38), recording start

time and station name appear instead of the programme title.

D ^{Select a programme.}

NOTES:

● If you do not want to use Programme Navigation function, set

“PROG. NAVIGATION” to “OFF” (੬ pg. 46).

● You cannot edit programme title or delete tape data for the

cassette with the record safety tab removed and “REC SAFETY”

is set to “ON” (੬ pg. 48).

Press rt to move the

highlight bar (pointer) to the

programme you want to

watch.

● Programme Navigation is possible with the cassettes recorded

with this recorder only.

● Before recording, make sure the recorder’s clock is set

correctly.

● To record the programme information in this recorder’s

memory, you must continue to record each programme for

over the minimum recording time; 8 minutes for the SP mode,

15 minutes for the LP mode or 23 minutes for the EP mode.

● Programme Navigation may not work properly depending on

the tape being used.

● The programme information is stored in this recorder’s

memory. If the memory in this recorder should ever be

damaged and the programme information lost, it is impossible

to restore that information.

E ^{Start playback.}

Press OK. “SEARCHING” appears on the TV screen.

Playback begins automatically after the selected

programme is located.

Download from Www.Somanuals.com. All Manuals Search And Download.

PROGRAMME NAVIGATION (cont.)

Edit Programme Title

You can edit the programme titles as you like.

Perform steps 1 to 3 of “Navigation Playback” on page 37

before continuing.

A ^{Select the programme.}

Press rt to move the

highlight bar (pointer) to the

programme you want to edit.

B ^{Access the Title Edit screen.}

Press the number key “1”.

The Title Edit screen appears.

C ^{Enter the programme title.}

Press the number keys and e

to enter characters, then

press OK. For details, refer to

“Entering Character” on

page 39.

D ^{Return to the normal screen.}

Press MENU.

Download from Www.Somanuals.com. All Manuals Search And Download.

Entering Character

Delete Tape Data

Perform steps 1 to 3 of “Navigation Playback” on page 37

before continuing.

Press the appropriate number key, then press e to enter

each character.

Refer to the example below.

(Example) Enter “JVC NEWS”

A ^{Delete the tape data.}

3 second. All the programme

data on the tape are deleted,

then normal screen appears.

● It is impossible to delete each

programme information.

A Press 5 (JKL) once to enter “J”, then press e.

B Press 8 (TUV) three times to enter “V”, then press e.

C Press 2 (ABC) three times to enter “C”, then press e.

D Press 0 (I) twice to enter “I (space)”, then press e.

E Press 6 (MNO) twice to enter “N”, then press e.

F Press 3 (DEF) twice to enter “E”, then press e.

G Press 9 (WXYZ) once to enter “W”, then press e.

H Press 7 (PQRS) four times to enter “S”, then press e.

Press & for more than

NUMBER KEY

CHARACTER

. , / – + f ( ) 1

A B C 2 Ä À Á Â Ã Å Æ

D E F 3 È É Ë Ê

G H I 4 Î Ï Ì Í

NOTE:

When you delete the tape data, only the tape information is

deleted from the recorder’s memory. The actual recording on the

tape is not erased.

J K L 5

M N O 6 Ö Ô Ò Ó Õ Ø Ñ

P Q R S 7

T U V 8 Ü Ù Û Ú

W X Y Z 9

0 I

NOTES:

● If you make a mistake, press w e to select the character, then

enter the correct character.

● If you want to delete a character, press w e to select the

character, then press &.

Download from Www.Somanuals.com. All Manuals Search And Download.

EDITING

You can use a camcorder as the source player and your

recorder as the recording deck.

Edit From A

Camcorder

A If the camcorder has no S-VIDEO output connector ...

Recorder

A ^{Make connections.}

A If the camcorder has no S-VIDEO output connector ...

... connect the camcorder’s AUDIO OUT and VIDEO

OUT connectors to the recorder’s front panel AUDIO

and VIDEO input connectors.

B If the camcorder has an S-VIDEO output connector ...

... connect the camcorder’s AUDIO OUT and

S-VIDEO OUT connectors to the recorder’s front panel

AUDIO and S-VIDEO input connectors.

● When using a monaural camcorder, connect its AUDIO OUT

connector to the AUDIO L input connector on your recorder.

B ^{Set the recorder’s input mode.}

Press AUX (number key “0”) and/or PR to select “F-1” for

the AUDIO and VIDEO input connectors, or “S-2” for the

AUDIO and S-VIDEO input connectors, depending on

the connectors being used.

AUDIO

input

VIDEO

input

Audio cable

C ^{Set the edit mode.}

Video cable

VIDEO OUT

See “PICTURE CONTROL” on page 45.

D ^{Start the camcorder.}

Engage the Play mode of the camcorder.

Camcorder

AUDIO OUT

E ^{Start the recorder.}

Player

Engage the Record mode of the recorder.

B If the camcorder has an S-VIDEO output connector ...

NOTES:

● All necessary cables can be obtained from your dealer.

● When you select “EDIT” to dub tapes in step 3, be sure to

select “AUTO” (or “NORM” when “B.E.S.T.” is set to “OFF”)

after you finish dubbing the tapes.

Recorder

● When you use this recorder as the recording deck for editing,

set “O.S.D. (PLAY)“ and “O.S.D. (REC)“ to “OFF“ (੬ pg. 45,

46) if you do not want to record the operational indicators

displayed on the TV screen.

● It is also possible to use the rear AUDIO/VIDEO IN or AUDIO/

S VIDEO IN connectors for the connection. When you use the

rear connectors, select “L-1” for the AUDIO/VIDEO IN

connectors, “S-1” for the AUDIO/S VIDEO IN connectors in

step 2.

AUDIO

input

S-VIDEO

input

Audio cable

S-Video cable

S-VIDEO OUT

Camcorder

AUDIO OUT

Player

Download from Www.Somanuals.com. All Manuals Search And Download.

You can use your recorder as the source player or as the

recording deck.

Edit To Or From

Another Video

A ^{Make connections.}

A When using your recorder as the source player ...

... connect its AUDIO/VIDEO OUT or AUDIO/S VIDEO

OUT connectors to the audio/video or audio/S-video

input connectors on another recorder.

B When using your recorder as the recording deck ...

... connect its AUDIO/VIDEO IN or AUDIO/S VIDEO IN

connectors to the audio/video or audio/S-video output

connectors on another recorder.

Recorder

TV receiver

Player

Your recorder

B ^{Set the input mode of recording deck.}

With this video recorder, press AUX (number key “0”)

and/or PR to select “L-1” for the AUDIO/VIDEO IN

connectors, or “S-1” for the AUDIO/S VIDEO IN

connectors, depending on the connector being used.

● When using another recorder as the recording deck, refer to its

instruction manual.

S-video cable

Audio/video

cable

C ^{Set the edit mode.}

Audio/video cable

Video

See “PICTURE CONTROL” on page 45.

channel or

AV mode

Another recorder

D ^{Start the source player.}

Recorder

Engage the Play mode of the source player.

TV receiver

Your recorder

E ^{Start the recording deck.}

Engage the Record mode of the recording deck.

NOTES:

● All necessary cables can be obtained from your dealer.

● When you select “EDIT” to dub tapes in step 3, be sure to

select “AUTO” (or “NORM” when “B.E.S.T.” is set to “OFF”)

after you finish dubbing the tapes.

● When you use this recorder as the source player for editing, be

sure to set “O.S.D. (PLAY)” to “OFF” before starting

(੬ pg. 46).

S-video cable

Audio/video

cable

Audio/video cable

● When you use this recorder as the recording deck for editing,

set “O.S.D. (PLAY)“ and “O.S.D. (REC)“ to “OFF“ (੬ pg. 45,

46) if you do not want to record the operational indicators

displayed on the TV screen.

● It is also possible to use the front AUDIO/VIDEO or AUDIO/

S-VIDEO input connectors for the connection. When you use

the front connectors, select “F-1” for the AUDIO/VIDEO input

connectors, “S-2” for the AUDIO/S-VIDEO input connectors

in step 2.

Video

channel or

AV mode

Another recorder

Player

Advantages of S-VHS video recorders

You can edit from VHS to S-VHS, S-VHS to VHS, or, from

S-VHS to S-VHS.

● From VHS to S-VHS: Record VHS playback signals in the

S-VHS mode. Although the picture quality is inherently

limited by that of the original, the edited tape has better

picture quality than those made by VHS-to-VHS editing.

● From S-VHS to VHS: Because the picture quality of the

source material is very high, the edited tape has better

picture quality than those made by VHS-to-VHS editing.

● From S-VHS to S-VHS: All signals will be transferred with

minimum degradation.

Download from Www.Somanuals.com. All Manuals Search And Download.

SYSTEM CONNECTIONS

Connecting To A Satellite Receiver

Connect the satellite receiver to the AUDIO/VIDEO IN or

NOTES:

S VIDEO IN connectors, then connect the AUDIO/

VIDEO OUT or S VIDEO OUT connectors to the TV’s

connectors.

● You cannot use Automatic Satellite Programme Recording

function if you connect the satellite receiver and the recorder

with S-video cable (੬ pg. 35).

● To record a programme via the satellite receiver, select L-1 or

S-1 mode by pressing AUX (number key “0”) and/or PR so that

“L-1” or “S-1” appears on the front display panel.

● For details, refer to the instruction manual of the satellite

receiver.

Outdoor unit

Audio/video input connectors

Aerial

Back of TV

TV aerial cable

Satellite cable

ANT. IN

Satellite receiver

Aerial

connector

S-video input

connector

RF OUT

Back of recorder

Mains outlet

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting/Using A Stereo System

These instructions enable you to connect your video recorder to your Hi-Fi stereo system (if you have one) and listen to

the soundtrack through the stereo.

FM tuner

CD player

Stereo amplifier

AUX IN or TAPE MONITOR

Audio cable

(not provided)

Speaker

Television

Speaker

Back of recorder

AUDIO OUT

Mains outlet

CAUTIONS:

Make connections.

● This recorder has a dynamic range of more than 80 dB with

regards to its Hi-Fi audio capability. It is recommended that

you check the maximum level if you are going to listen to the

Hi-Fi audio signals through a stereo amplifier. A sudden surge

in the input level to the speakers may damage them.

Connect the AUDIO OUT L and R connectors on your

video recorder to the AUX IN or TAPE MONITOR

connectors on your stereo system’s receiver or amplifier.

● Some speakers and televisions are specially shielded to

prevent television interference. If both are of the non-shielded

type, do not place the speakers adjacent to the TV set as this

can adversely affect the video playback picture.

NOTE:

When listening to sound through the connected stereo system,

turn the TV’s volume down completely.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS

You can change various mode settings on the Mode Set

screen by following the procedure described below.

● For each mode setting, see pages 45 to 48.

Mode Set

Turn on the TV and select the video channel (or

AV mode).

A ^{Access the Main Menu screen.}

Press MENU.

B ^{Access the Mode Set screen.}

Press rt to move the

highlight bar (pointer) to

“MODE SET”, then press OK

or e.

C ^{Select the mode.}

Press rt to move the highlight bar (pointer) to the item

you want to change.

D ^{Select the mode setting.}

Press OK or e.

E ^{Return to the normal screen.}

Press MENU.

ATTENTION

● The setting you have made is kept in memory if the lithium

battery is not exhausted. Even if the recorder is unplugged

or the power failure occurs, it will resume every time you

turn on the recorder (੬ pg. 14).

● You cannot change the mode settings on the Mode Set

screen during recording (੬ pg. 19).

Download from Www.Somanuals.com. All Manuals Search And Download.

* The default setting is bold in the table below.

Your recorder is equipped with the Digital TBC (Time Base Corrector) that removes

jitter from fluctuating video signals to deliver a stable picture even with old tapes and

rental cassettes.

The on/off of Digital 3-DNR (Noise Reduction) which cuts noise and enables clear

picture reproduction is also linked to this function.

⁸DIGITAL TBC/NR

OFF

We recommend that you set “DIGITAL TBC/NR” to “ON” when...

... playing back a tape recorded on a camcorder.

... playing back a tape repeatedly used.

... using this video recorder as the source player for editing.

NOTES:

● If you play back a tape recorded under poor TV reception condition, the picture may become

more stable with Digital TBC/NR set to off.

● When “DIGITAL TBC/NR” is set to “ON”, if you play back a tape where certain types of signals

are recorded (using a PC or some character generators), the playback picture may be distorted.

If this is the case, set “DIGITAL TBC/NR” to “OFF”.

● When playing back a MESECAM tape, Digital TBC/NR does not function even though “DIGITAL

TBC/NR” is set to “ON”.

You can set the B.E.S.T. (Biconditional Equalised Signal Tracking) system to “ON” or

“OFF” (੬ pg. 23).

⁸B.E.S.T.

OFF

This feature helps you to adjust the playback picture quality according to your

preference. Normally select “AUTO”.

⁸PICTURE CONTROL

AUTO

EDIT

AUTO

EDIT

SOFT

Provides the optimised picture benefits of the B.E.S.T. Picture System.

Minimizes picture degradation during editing (recording and playback).

Reduces image coarseness when viewing overplayed tapes containing a lot

of noise.

SOFT

SHARP

Clearer, sharper-edged picture when viewing images with lots of flat,

same-coloured surfaces such as cartoons.

NOTES:

● When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will not change until you

select another mode.

● When you select “EDIT” to dub tapes, be sure to select “AUTO” after you finish dubbing the

tapes.

● When “B.E.S.T.” is “OFF”, “PICTURE CONTROL” switches automatically from “AUTO” to

“NORM”.

When this function is set to “ON”, the timer is automatically engaged when the

recorder power is turned off, and automatically disengaged when the recorder is

powered back on.

⁸AUTO TIMER

OFF

NOTE:

For safety, when “AUTO TIMER” is set to “OFF”, all other recorder functions are disabled while

the Timer mode is engaged. To disengage the timer, press # (TIMER).

When this function is set to “ON”, all the indicators displayed on the TV screen will be

recorded. If you do not want to record the indicators, select “OFF”.

⁸O.S.D. (REC)

OFF

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

* The default setting is bold in the table below.

When this function is set to “ON”, various operational indicators appear on the TV

screen.

⁸O.S.D. (PLAY)

OFF

NOTES:

● When you use this recorder as the source player for editing, be sure to set “O.S.D. (PLAY)” to

“OFF” before starting.

● During playback, the operation mode indicators may be disturbed depending on the type of

tape being used.

When this function is set to “ON”, the recorder stores information on the recorded

programmes. If you do not want to use the Programme Navigation function (੬ pg. 36),

set “PROG. NAVIGATION” to “OFF”.

⁸PROG. NAVIGATION

OFF

NOTES:

● Programme Navigation is possible with the cassettes recorded with this recorder only.

● Before recording, make sure the recorder’s clock is set correctly.

● To record the programme information in this recorder’s memory, you must continue to record

each programme for over the minimum recording time; 8 minutes for the SP mode, 15 minutes

for the LP mode or 23 minutes for the EP mode.

● Programme Navigation may not work properly depending on the tape being used.

● The programme information is stored in this recorder’s memory. If the memory in this recorder

should ever be damaged and the programme information lost, it is impossible to restore that

information.

When this function is set to “ON”, the recorder automatically switches to LP mode to

allow complete recording if there is not enough tape to record the entire programme

while timer-recording in SP mode.

⁸AUTO SP^]LP TIMER

OFF

For Example . . .

Recording a programme of 210 minutes in length onto a 180-minute tape

Approximately 150 minutes

SP mode

Approximately 60 minutes

LP mode

Total 210 minutes

Make sure you set this function to “ON”, before the timer-recording starts.

NOTES:

● If you have programmed the recorder to timer-record 2 or more programmes, the second

programme and those thereafter may not fit on the tape if you set “AUTO SP]LP TIMER” to

“ON”. In this case, make sure the mode is not engaged, then set the tape speed manually

during timer programming.

● In order to ensure that the recording fits on the tape, this feature may leave a slight

non-recorded section at the end of the tape.

● There may be some noise and sound disturbance at the point on the tape where the recorder

switches from SP to LP mode.

● The Auto SP]LP Timer feature will not work properly with any tapes longer than E-180, or with

some tapes of shorter lengths.

● If you perform timer recording with both VPS/PDC and the Auto SP]LP Timer activated, and

the programme goes beyond its originally scheduled length, there may be times when the

programme cannot be recorded in its entirety.

Download from Www.Somanuals.com. All Manuals Search And Download.

* The default setting is bold in the table below.

When this function is set to “ON”, the Digital 3R picture system applies edge

⁸DIGITAL 3R

correction to the luminance signal to enhance detail.

OFF

NOTES:

● Normally it is recommended to keep “DIGITAL 3R” set to “ON”.

● Depending on the type of tape being used, picture quality may be better with “DIGITAL 3R” set

to “OFF”.

● If you use the recorder as the source player for editing, be sure to set “DIGITAL 3R” to “OFF”

before starting.

When this function is set to “ON”, you can reduce the power consumption while the

recorder is turned off.

⁸POWER SAVE

OFF

NOTES:

● During Power Save mode ...

... the front display panel will be turned off.

... the Just Clock function (੬ pg. 56) does not work.

... the picture may be distorted momentarily when you turn on/off the recorder.

● Power Save does not work when ...

... the recorder is in the Timer mode.

... the recorder’s power is turned off after timer-recording.

... the Automatic Satellite Programme Recording mode is engaged (੬ pg. 35).

When this function is set to “ON”, you can automatically correct vertical vibration in

the picture when playing back unstable recordings made on another recorder.

⁸VIDEO STABILIZER

OFF

NOTES:

● When you finish viewing a tape, be sure to set this function to “OFF”.

● Regardless of the setting, this function has no effect during recording and during special effects

playback.

● The on-screen display may jitter vertically when this function is set to “ON”.

● To watch recordings with close-caption, set this function to “OFF”.

● Video Stabilizer and Digital TBC/NR cannot be used at the same time. If you activate Digital

TBC/NR when “VIDEO STABILIZER” is set to “ON”, Video Stabilizer will be automatically

turned “OFF”.

Your recorder can record in S-VHS (Super VHS), S-VHS ET or VHS.

⁸S-VHS

● To record in S-VHS:

OFF

Set “S-VHS” to “ON”. Then, insert a cassette marked “S-VHS”. The S-VHS indicator

lights up on the front display panel.

The S-VHS recording mode is selected.

● To record in S-VHS ET on a VHS cassette:

See “Super VHS ET (S-VHS ET)” on page 22.

● To record in VHS:

Insert a cassette marked “VHS”.

Press S-VHS ET on the recorder. You can check the current setting (“S-VHS ET : ON” or

“S-VHS ET : OFF”). If “S-VHS ET : ON” appears on the TV screen, press S-VHS ET

again in about 5 seconds to set it to “OFF”.

The VHS recording mode is automatically selected regardless of the “S-VHS” mode

setting.

● To record in VHS on an S-VHS cassette:

Insert a cassette marked “S-VHS”. The S-VHS indicator lights up on the front display

panel. Then, set “S-VHS” to “OFF”. The S-VHS indicator goes off.

The VHS recording mode is selected.

NOTE:

When playing back a tape that has been recorded in S-VHS or S-VHS ET, the S-VHS indicator

lights up on the front display panel regardless of the “S-VHS” mode setting.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

* The default setting is bold in the table below.

You can play back PAL, NTSC and MESECAM tapes, or record PAL and SECAM* signals

on this recorder. Select the appropriate colour system.

* SECAM signals will be recorded as MESECAM on this recorder; MESECAM is the designation for

tapes with SECAM signals that have been recorded on a MESECAM-compatible PAL video

cassette recorder.

⁸COLOUR SYSTEM

AUTO**

PAL/NTSC

MESECAM

AUTO**:

Normally set to this mode. The appropriate colour system is selected

automatically depending on the playback or recording signals.

** You can select “AUTO” only when “OTHER EASTERN EUROPE” is selected for the country setting

(੬ pg. 12). In this case, the default setting is “AUTO”.

If the “AUTO” mode does not function properly, select the following manual mode.

PAL/NTSC: To record PAL signals, or play back a PAL or NTSC tape.

MESECAM: To record SECAM signals, or play back a MESECAM tape.

NOTES:

● It is not possible to record in S-VHS if “MESECAM” is selected. The recording mode is forced to

change to VHS.

● If “MESECAM” is selected when the tape speed is set to EP mode, the tape speed will be forced

to change to LP mode.

● It is not possible to select EP mode if “MESECAM” is selected.

About NTSC Playback

● Some TVs shrink the picture vertically and place black bars at the top and bottom of the TV

screen. This is not a malfunction on the part of either the video recorder or the TV.

● The picture may roll up and down. This can be corrected using the V-HOLD control found on

some TVs. (This cannot be corrected if the TV does not have a V-HOLD control.)

● The counter and tape remaining time readings will be incorrect.

● During search, still, or frame-by-frame playback, the picture will be distorted, and there may be

a loss of colour.

● Depending on the type of TV, the top and bottom portions of superimposed displays may be cut

off during NTSC playback.

Returning point for Playback, Repeat Playback or Series Playback can be set to tape

end or recording end. (This recorder considers 1-second unrecorded portion as the

recording end.) When the returning point is reached, playback stops and the cassette

will be automatically rewound.

⁸RETURN POINT

TAPE END

REC END

TAPE END: Playback stops at the end of tape.

REC END:

Playback stops at the end of the recording.

When this function is set to “ON”, you can record Month/Day/Year and clock time

display with your picture.

⁸DAY/TIME INSERT

OFF

NOTE:

To use this function, be sure to set “O.S.D. (REC)” to “ON” (੬ pg. 45). Only Month/Day/Year and

clock time displays appear.

Usually, you can only record onto a cassette with its record safety tab intact. When the

this function is set to “OFF”, recording can be done onto a cassette whose record safety

tab is removed.

⁸REC SAFETY

OFF

NOTE:

When “REC SAFETY” is set to “OFF”, playback does not start automatically when you insert a

cassette with its record safety tab removed. (੬ pg. 15).

When you set daily timer recording, you can use one cassette repeatedly. If you select

“AUTO REW”, the recorder rewinds tape each time after timer recording and the timer

mode is engaged.

⁸DAILY T. RECORD

NORM

AUTO REW

If you select “NORM”, the recorder turns off after timer recording.

Download from Www.Somanuals.com. All Manuals Search And Download.

SHOWVIEW^®System Setup

IMPORTANT

Normally, Auto Set Up (੬ pg. 12) or Auto Channel Set (੬ pg. 50) sets the Guide Program numbers automatically. You need to set

the Guide Program numbers manually only in the following cases.

● When timer-programming with the SHOWVIEW system, the channel position, where the station you wish to record is received on

your recorder, is not selected,

when you add a channel after Auto Set Up or Auto Channel Set has taken place,

—Set the Guide Program number for that station manually.

● When you wish to timer-record a satellite programme with the SHOWVIEW system,

—Set the Guide Program numbers for all satellite broadcasts received on your satellite receiver.

Turn on the TV and select the video channel (or

AV mode).

Guide Program Number Set

E ^{Enter the receiving channel position number.}

Press rt or number keys to

A ^{Access the Main Menu screen.}

input the number of the

recorder’s channel position on

Press MENU.

which the Guide Program

number’s broadcast is received

by the recorder. Then press OK

B ^{Access the Initial Set screen.}

or e.

● If the satellite broadcast is

received on your recorder’s

auxiliary channel “L-1”, select

“L-1” for the channel position.

● Repeat steps 4 and 5 as

necessary.

Press rt to move the highlight bar (pointer) to “INITIAL

SET”, then press OK or e.

(Example) If ZDF is received on

channel position 2.

C ^{Access the Guide Program Set screen.}

Press rt to move the highlight bar (pointer) to “GUIDE

PROG SET”, then press OK or e.

F ^{Return to the normal screen.}

Press MENU.

D ^{Enter the Guide Program number.}

Press rt or number keys to

enter the Guide Program

number for the desired station

as shown in the TV listings.

Then press OK or e.

Guide Program Number

“Guide Program (GUIDE PROG) number” refers to the

assigned TV station numbers, according to broadcast area,

for the SHOWVIEW timer recording. The Guide Program

numbers can be found in most TV listings.

(Example) When inputting the

Guide Program

number 2 for ZDF.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

IMPORTANT

Perform the following steps only if —

— Auto Channel Set has not been set correctly by Auto Set

Up (੬ pg. 12).

Tuner Set

— you have moved to a different area or if a new station

starts broadcasting in your area.

Turn on the TV and select the video channel (or

AV mode).

Your recorder needs to memorize all necessary stations in

channel positions in order to record TV programmes. Auto

Channel Set automatically assigns all receivable stations in your

area to call them up by using the PR buttons without going

through any vacant channels.

Auto Channel Set

A ^{Turn on the recorder.}

Press 1.

B ^{Access the Main Menu screen.}

Press MENU.

C ^{Access the Auto Channel Set screen.}

Press rt to move the

highlight bar (pointer) to

“AUTO CH SET”, then press

OK or e.

D ^{Select your country.}

Press rt to move the highlight bar (pointer) to your

country’s name.

Download from Www.Somanuals.com. All Manuals Search And Download.

E ^{Perform Auto Channel Set.}

Press OK.

● The Auto Set screen appears,

and remains on screen while

the recorder searches for

receivable stations.

As Auto Channel Set

progresses, the “q” mark on

the TV screen moves from

left to right. Wait until the TV

screen as shown in step 6

Beginning

appears.

End

F ^{View the Confirmation screen.}

After “SCAN COMPLETED” is

displayed on the TV screen for

about 5 seconds, the

Confirmation screen looking

like the one to the right

appears. The stations your

recorder located appear on a

Confirmation screen —

channel positions (PR),

channels (CH) and station names (ID – ੬ pg. 55). The

blueback screen and the programme currently being

broadcast by the blinking station appear alternately for 8

seconds each. To view the next page, use the rt w e

button on the remote control.

● The stations located in the selected country appear at the top

of the list.

● The Guide Program numbers will also be set automatically

during Auto Channel Set.

G ^{Return to the normal screen.}

● Using the Confirmation screen, you can skip or add channel

positions, enter station names and perform other operations.

Refer to pages 52 – 54 for the procedures.

● Depending on reception conditions, the stations may not be

stored in order, and the station names may not be stored

correctly.

Press MENU.

IMPORTANT

● In certain reception conditions, station names may not be

stored correctly, and Auto Guide Program Number Set may

not work properly. If the Guide Program numbers are not

set properly when you timer-record a TV programme using

the SHOWVIEW system, the recorder will record a TV

programme of a different station. When programming the

timer using the SHOWVIEW system, be sure to check the

desired channel is selected correctly (੬ pg. 28,

“SHOWVIEW^®Timer Programming”).

● Your video recorder memorizes all detected stations even if

reception of some of them is poor. You can delete those

stations with an unacceptable picture (੬ pg. 53, “Delete

A Channel”).

NOTES:

● Fine tuning is performed automatically during Auto Channel

Set. If you want to perform tuning manually, refer to page 54.

● If you perform Auto Channel Set when the aerial cable is not

connected properly, “SCAN COMPLETED –NO SIGNAL–”

appears on the TV screen in step 6. When this happens, make

sure of the aerial connection and press OK; Auto Channel Set

will take place again.

● If no sound accompanies the picture or the audio sounds

unnatural on some channels that have been stored by Auto Set

Up, the TV system setting for those channels may be incorrect.

Select the appropriate TV system for those channels

(੬ pg. 53, “INFORMATION”).

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

D ^{Select the band.}

Press rt to change the band

between CH (regular) and CC

(cable), then press e.

E ^{Input the channel.}

Press the number keys to input the channel number you

want to store.

● Input “0” before any single number entries.

● To input the registered station name (ID – ੬ pg. 55), press e

until “– – – –” (ID setting) begins blinking, then press rt.

● For fine tuning adjustment, press e until “+/–” begins blinking,

then press rt. While tuning, “+” or “–” appears.

F ^{Enter new channel information.}

Press OK and the Confirmation screen appears.

● Repeat steps 3 – 6 as necessary.

Manual Channel Set

Store channels that were not stored during Auto Set Up

G ^{Close the Confirmation screen.}

(੬ pg. 12) or Auto Channel Set (੬ pg. 50).

Press MENU.

● To change positions, see “Change Station Channel Position”

(੬ pg. 53).

A ^{Access the Main Menu screen.}

● If you wish to set station names other than the ones registered

in your recorder, see “Set Stations (B)” (੬ pg. 54).

Press MENU.

B ^{Access the Confirmation screen.}

ATTENTION

Guide Program numbers are not set when channels are

stored manually. If an attempt is made at timer programming

with the SHOWVIEW system in this state, the “GUIDE PROG

SET” screen appears; set the Guide Program numbers on this

screen. (੬ pg. 29, “ATTENTION — Guide Program Number

Set”)

Press rt to move the highlight bar (pointer) to

“MANUAL CH SET”, then press OK or e. The

Confirmation screen appears.

C ^{Select the channel position.}

Or perform “Guide Program Number Set” (੬ pg. 49).

(Example) To store in position 12.

Press rt w e until an open

position in which you want to

store a channel begins

blinking, then press OK. The

Manual Channel Set screen

appears.

The blueback screen and the

programme currently being

broadcast by the selected channel

appear alternately for 8 seconds

each.

Download from Www.Somanuals.com. All Manuals Search And Download.

Delete A Channel

Perform steps 1 and 2 of “Manual Channel Set” on page 52

to access the Confirmation screen before continuing.

Change Station Channel Position

Perform steps 1 and 2 of “Manual Channel Set” on page 52

to access the Confirmation screen before continuing.

A ^{Select the item.}

blinking.

A ^{Select the item.}

Press rt w e until the item you want to delete begins

Press rt w e until the item you want to move begins

blinking. Then press OK and the station name (ID) and its

channel (CH) number begin blinking.

B ^{Delete a channel.}

B ^{Select the new position.}

Press &.

● The item directly beneath the cancelled one moves up one

Press rt w e to move the station to the new channel

position, then press OK.

line.

● Repeat steps 1 and 2 as necessary.

Example: If you moved the station in position 4 to position 2, the

stations originally in positions 2 and 3 each move

down one space.

C ^{Close the Confirmation screen.}

Press MENU.

INFORMATION

If you live in Eastern Europe, “TV SYSTEM” setting appears

on the Manual Channel Set screen. When you can see the

picture but can hear no audio, select appropriate TV system

(D/K or B/G). Normally, TV programmes are broadcasted as

follows.

● Repeat steps 1 and 2 as necessary.

For Eastern Europe : D/K

For Western Europe : B/G

C ^{Close the Confirmation screen.}

A Select a country in Eastern Europe in step 4 on page 50.

B Press e until the TV system (D/K or B/G) blinking on the

Manual Channel Set screen in step 4 on page 52.

C Press rt to select appropriate TV System (D/K or B/G).

Press MENU.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

Set Stations (A)

B ^{Enter the new character.}

Set station names that are registered in your recorder.

Press rt to cycle through the characters (A–Z, 0–9, –, f,

+, I (space) ) and stop when the desired character is

indicated, then press e to enter. Enter the remaining

characters the same way (maximum of 4). After entering

all characters, press OK.

Perform steps 1 and 2 of “Manual Channel Set” on page 52

to access the Confirmation screen before continuing.

A ^{Select the item.}

● The Confirmation screen appears.

● If you make a mistake, press w until the incorrect character

begins blinking. Then enter the correct character by pressing

rt.

Press rt w e until the item you want begins blinking.

B ^{Access the Manual Channel Set screen.}

C ^{Close the Confirmation screen.}

Press OK twice.

Press MENU.

C ^{Select the new station.}

NOTE:

The characters available for the station name (ID) are A–Z, 0–9,

Press e until the station

name (ID) begins blinking,

then press rt until the new

station’s name (ID) you want

to store begins blinking.

Registered station names

(੬ pg. 55) appear as you

press rt.

–, f, +, I (space) (maximum of 4).

Fine-Tuning Channels Already Stored

Perform steps 1 and 2 of “Manual Channel Set” on page 52

to access the Confirmation screen before continuing.

A ^{Select the channel to fine-tune.}

blinking.

D ^{Switch the stations.}

● The Confirmation screen appears.

● Repeat steps 1 – 4 as necessary.

Press rt w e until the channel you want to tune begins

Press OK.

B ^{Access the Manual Channel Set screen.}

E ^{Close the Confirmation screen.}

Press OK twice. The Manual Channel Set screen appears.

Press MENU.

C ^{Perform tuning.}

Press e until “+/–” begins blinking, then press rt until

the picture is its clearest. Then press OK.

● The Confirmation screen appears.

Set Stations (B)

Set station names other than the ones registered in your recorder.

● Repeat steps 1 – 3 as necessary.

Perform steps 1 and 2 of “Manual Channel Set” on page 52

to access the Confirmation screen and then perform steps 1

and 2 of “Set Stations (A)” above before continuing.

D ^{Close the Confirmation screen.}

Press MENU.

A ^{Select the character for station name.}

Press e until the first letter of

the station name begins

blinking.

Download from Www.Somanuals.com. All Manuals Search And Download.

TV Station And ID List

ID*

STATION NAME

ID*

STATION NAME

1000

3SAT

9LIV

ADLT

ANT3

ARD

ARTE

TV1000

3SAT

ORF2

ORF3

OWL3

PREM

PRO7

RAI1

RAI2

RAI3

RET4

RTBF

RTL

RTL2

RTL4

RTL5

RTP

SAT1

SBS

SF1

SF2

SHOW

SIC

SKY

SKYN

SPRT

SRTL

STAR

SVT1

SVT2

SWR

TCC

TELE

TEL5

TF1

ORF2

ORF3

9LIVE

OWL3

PREMIERE

PRO7

ADULT

ANTENA3

ARD

RAI1

ARTE

RAI2

BERLIN1

BBC GROUP

BBC1

RAI3

BBC

RETE4

TELE21

RTBF1 or 2

RTL

BBC1

BBC2

BR3

C+

BBC2

BAYERN3

CANAL PLUS

PORTUGUSES

CANALE5

KETNET CANVAS

CHANNEL4

CHANNEL5

CHILD

RTL2

RTL4

CAN5

CANV

CH4

CH5

CHLD

CINE

CLUB

CMT

CNN

CSUR

DISC

RTL5

RTP

SCHWEIZ4

SAT1

SBS

CINEMA

TELECLUB

CMT

SF1

SF2

SHOW

SOCIEDADE

SKY CHANNEL

SKY NEWS

SPORT

SUPER RTL

STAR-TV

SVT1

CNN

ANDALUCIA

DISCOVERY

DR TV

DR2

DRS

DSF

ETB1

ETB2

EURO

EUSP

FEMM

FILM

FNET

FR2

ETB1

SVT2

ETB2

SUEDWEST3

TCC

EURONEWS

EUROSPORTS

FEMMAN

FILM

TELE

TELE5

TF1

FILMNET

France2

France3

GALAVISION

HESSEN3

INFO-KANAL

ITALIA1

ITALIA7

ITV1

JSTV

KA2

KABEL1

KANAL2

LOCAL

MBR

MCM

MDR

MOVIE

MTV

MTV3

TMC

TNT

TRT

TELEMONTECARLO

TNT INT

TRT INT

TSI

FR3

GALA

HR3

INFO

ITA1

ITA7

ITV

JSTV

KA2

KAB1

KAN2

LOCA

MBC

MCM

MDR

MOVE

MTV

MTV3

N-TV

NBC

NDR3

NED1

NED2

NED3

NEWS

NICK

NRK

NRK2

ODE

ORF1

TSI

TSR

TV1

BRTN TV1

TV2

TV3

TV4

TV5

TV6

TVE1

TVE2

TVG

TVI

TVE1

TVE2

TV GALICIA

TV INDEPENDENT

TV NORGE

VIDEO

VERONICA

VH-1

TVN

VCR

VERO

VH-1

VIVA

VIV2

VMTV

VOX

VT4

VTM

WDR1

WDR3

YLE1

YLE2

ZDF

ZTV

VIVA

VIVA2

VIDEO MUSIC

VOX

VT4

VTM

West1

West3

YLE1

YLE2

ZDF

ZTV

NORD3

N-TV

NBC SUPER

NDR3

NED1

NED2

NED3

NICKELODEON

NRK

NRK2

ODEON

ORF1

* The “ID” abbreviation is what is shown on-screen in lieu of the station

name. The “ID” abbreviation is listed in the Confirmation screen and is

displayed on the TV screen when the recorder is tuned to a different

station.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

IMPORTANT

If you performed Auto Set Up (੬ pg. 12) without ever

Clock Set

having set the clock previously, the recorder’s built-in clock is

also set automatically.

Perform the following steps only if —

—Auto Clock Set has not been performed correctly by Auto

Set Up.

Turn on the TV and select the video channel (or

AV mode).

—the recorder’s memory backup has expired.

—you want to change Just Clock setting (੬ “Just Clock” in

the left column).

A ^{Turn on the recorder.}

Press 1.

B ^{Access the Main Menu screen.}

Press MENU.

C ^{Access the Initial Set screen.}

Press rt to move the highlight bar (pointer) to “INITIAL

SET”, then press OK or e.

D ^{Access the Clock Set screen.}

Press rt to move the highlight bar (pointer) to “CLOCK

SET”, then press OK or e. The Clock Set screen appears.

NOTE:

When you have selected MAGYARORSZÁG, CESKÁ

REPUBLIKA, POLSKA or OTHER EASTERN EUROPE for the

country setting (੬ pg. 12), you cannot use Just Clock function.

Skip steps 6 and 7 on page 57.

Just Clock

The Just Clock function provides accurate time keeping

through automatic adjustments at regular intervals, by

reading data from a PDC signal.

The Just Clock option can be set “ON” or “OFF” at the Clock

Set screen (the default setting is “OFF”). Press OK until the

Just Clock setting begins blinking, then press rt to change

the setting.

IMPORTANT: If you turn off Just Clock, the accuracy of your

recorder’s built-in clock may be reduced, which could

adversely effect timer recording. We recommend you to keep

Just Clock on. In cases where the clock setting data from a

PDC signal is incorrect, however, you are advised to keep

Just Clock set to “OFF”.

Download from Www.Somanuals.com. All Manuals Search And Download.

E ^{Set the date and time.}

Press rt to set the time, then press OK or e. The

“DATE” display begins blinking. Repeat the same

procedure to set the date and year.

● When you set the time, press and hold rt to change the time

by 30 minutes.

● When you set the date, press and hold rt to change the date

by 15 days.

F ^{Set Just Clock.}

The default setting is “OFF”. Set as desired by pressing

rt, then press OK or e.

● For the Just clock function, refer to “Just Clock” on page 56.

● If you set to “OFF”, you can disregard the next step as you

won’t be able to receive regular clock adjustments.

Set the source channel position for clock

data.

The recorder is preset to receive clock setting and

adjustment data from channel position 1.

Press rt to set the channel position to the number

representing the station transmitting clock setting data,

then press OK or e.

H ^{Start the clock operation.}

Press MENU.

NOTES:

● Just Clock (when set to “ON”) adjusts the recorder’s built-in

clock every hour, except for 23:00, 0:00, 1:00 and 2:00.

● Just Clock is not effective when ...

... the recorder’s power is on.

... the recorder is in the Timer mode.

... a difference of more than 3 minutes exists between the

built-in clock’s time and the actual time.

... the recorder is in the Automatic Satellite Programme

Recording mode (੬ pg. 35).

... the recorder is in the Power Save mode (੬ pg. 47).

● If Just Clock is set to “ON”, the recorder’s clock is

automatically adjusted at the start/end of Summer Time.

● Just Clock may not function properly depending on the

reception condition.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

Video Channel Set

Video channel (RF output channel) is the channel on which your TV receives picture and sound signals from the recorder through the

RF cable.

IMPORTANT

Perform the following steps only if —

— Video Channel Set has not been done correctly by the Auto Set Up function (੬ pg. 12),

— interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your

area.

— you change the connection between your recorder and TV from RF connection to AV or S-VIDEO connection, or vice versa.

If you have connected the recorder to your TV via the AV or S-VIDEO connection (੬ pg. 10, 11), since you do not

need the video channel you have to set the video channel to off.

If you have connected the recorder to your TV via the RF connection (੬ pg. 10), you have to set the correct video

channel.

Before performing the following steps:

Make sure the recorder’s power is off and there is no cassette inserted in the recorder.

Then set your TV to UHF channel 50.

● If the two vertical white bars appear

A ^{Access the Video Channel Set mode.}

panel shows the following.

clearly on the TV screen as shown to

the right, go to step 4.

● If the two vertical white bars do not

appear clearly, re-set the video

recorder to another vacant channel

and try again.

Hold down 0 on the recorder until the front display

NOTES:

● If you set the video recorder to a channel which is occupied by

a local station or has neighbouring channels that are occupied

B ^{Set the RF output system.}

by local stations, the picture reception quality will be affected

and some interference noise will appear on the TV screen. Be

The blinking number on the display indicates the RF

sure to select a vacant channel which has no broadcast on

output system of your country.

neighbouring channels.

● If you have selected MAGYARORSZÁG, CESKÁ REPUBLIKA,

● If you cannot obtain the two vertical white bars clearly with

POLSKA or OTHER EASTERN EUROPE for the country setting

any channel between 22 and 69, consult your JVC dealer.

(੬ pg. 12), press rt to set to “2”.

● For other countries, set to “1”. Then press OK.

(1: B/G 2: D/K)

D ^{Exit the Video Channel Set mode.}

Press OK on the remote control.

With AV or S-VIDEO Connection

C ^{Set the video channel.}

Press PR – until the front display panel shows “1 – –” (or

To view picture signals from the video recorder, set

your TV to its AV mode.

With AV or S-VIDEO Connection

With RF Connection

The channel on which the TV screen in step 3 appears

clearly is your video channel.

“2 – –”).

To view picture signals from the video recorder, set

your TV to the video channel.

● Now the video channel is set to off.

With RF Connection

Press PR + or – to set the video recorder to a vacant

channel between 22 and 69 which is not occupied by

any local station in your area.

(Example) If channel 50 is available in your area

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are

often easily corrected, and this can save you the trouble of sending your video recorder off for repair.

POWER

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1. No power is supplied to the recorder.

● The mains power cord is disconnected. Connect the mains power cord.

2. The clock is functioning properly, but

the recorder cannot be powered.

● “#” is displayed on the front display Press the # button to turn the “#”

panel with “AUTO TIMER” set to “OFF”. indicator off.

3. The remote control won’t function.

● The batteries are discharged.

Replace the dead batteries with new ones.

TAPE TRANSPORT

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1. During recording, the tape does not

run. “⅜” lights up and the channel

display blinks on the front display

panel.

● The recorder is in the Record Pause

mode.

Press 4 to resume recording.

2. The tape will not rewind or

fast-forward.

● The tape is already fully rewound or

fast-forwarded.

Check the cassette.

PLAYBACK

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1. The playback picture does not appear

while the tape is running.

● If you are using the RF connection,

If you are using the RF connection,

. . . the TV receiver’s channel selector is . . . set the TV receiver to the video

not set to the video channel.

channel.

. . . the recorder’s video channel has not . . . perform “Video Channel Set”

been correctly set.

(੬ pg. 58).

● If you are using the AV or S-VIDEO

If you are using the AV or S-VIDEO

connection, the TV receiver is not set to connection, set the TV to its AV mode.

the AV mode.

2. Noise appears during visual search.

● This is normal.

3. Noise appears during normal

playback.

● The automatic tracking mode is

engaged.

Try manual tracking. (੬ pg. 18)

4. The playback picture is blurred or

interrupted while TV broadcasts are

clear or “USE CLEANING CASSETTE”

message appears on the screen.

● The video heads may be dirty.

Use a dry cleaning cassette TCL-2 or

consult your JVC dealer.

5. Breaks are noticeable in Hi-Fi

soundtrack.

● The automatic tracking mode is

engaged.

Try manual tracking. (੬ pg. 18)

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING (cont.)

RECORDING

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1. Recording cannot be started.

● There is no cassette loaded.

Load a cassette with the record safety tab

intact. If the tab has been removed, set

“REC SAFETY” to “OFF” (੬ pg. 48).

● The loaded cassette has had its record

safety tab removed and “REC SAFETY”

is set to “ON”.

Set “REC SAFETY” to “OFF” (੬ pg. 48),

or using adhesive tape, cover the hole

where the tab was removed.

2. TV broadcasts cannot be recorded.

3. Tape-to-tape editing is not possible.

● “L-1”, “F-1”, “S-1” or “S-2” has been

Set to the desired channel.

selected as the input mode.

● The source (another video recorder,

camcorder) has not been properly

connected.

Confirm that the source is properly

connected.

● All necessary power switches have not

been turned on.

Confirm that all units’ power switches are

turned on.

● The input mode is not correct.

Set the input mode to “L-1”, “F-1”, “S-1”

or “S-2”.

4. Camcorder recording is not possible.

● The camcorder has not been properly

connected.

Confirm that the camcorder is properly

connected.

● The input mode is not correct.

Set the input mode to “L-1”, “F-1”, “S-1”

or “S-2”.

5. The recorder automatically rewinds

the tape to the beginning.

● The end of the tape was reached during The programme may not have been

recording.

recorded in its entirety. Next time make

sure you have enough time on the tape to

record the entire programme.

TIMER RECORDING

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1. Timer recording won’t work.

● The clock and/or the timer have been set Re-perform the clock and/or timer

incorrectly.

settings.

● The timer is not engaged.

Press # and confirm that “#” is displayed

on the front display panel.

2. Timer programming is not possible.

● Timer recording is in progress.

Timer programming can’t be performed

while a timer recording is in progress.

Wait until it finishes.

3. “#” on the front display panel won’t

● The timer is engaged but there’s no

cassette loaded.

Load a cassette with the record safety tab

intact. If the tab has been removed, set

“REC SAFETY” to “OFF” (੬ pg. 48).

stop blinking.

4. “#”, “⅜” and “$” on the front

● The loaded cassette has had its record

safety tab removed and “REC SAFETY”

is set to “ON”.

Set “REC SAFETY” to “OFF” (੬ pg. 48),

or using adhesive tape, cover the hole

where the tab was removed.

display panel won’t stop blinking.

● The end of the tape was reached during The programme may not have been

timer recording.

recorded in its entirety. Next time make

sure you have enough time on the tape to

record the entire programme.

5. “#” blinks for 10 seconds and the

● # has been pressed when there are no

programs in memory, or the timer

record information has been

Check the programmed data and re-

program as necessary, then press # again.

Timer mode is disengaged.

programmed incorrectly.

6. The SHOWVIEW system does not

timer-record properly.

● The recorder’s channel positions have

been set incorrectly.

Refer to “Guide Program Number Set”

(੬ pg. 49) and re-perform the procedure.

Download from Www.Somanuals.com. All Manuals Search And Download.

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

7. “ “, “⅜” and “$“ on the front

● The loaded cassette has had its record

safety tab removed and “REC SAFETY”

is set to “ON”.

Set “REC SAFETY” to “OFF” (੬ pg. 48),

or using adhesive tape, cover the hole

where the tab was removed.

display panel won’t stop blinking.

● The end of the tape was reached during The programme may not have been

Automatic Satellite Programme

Recording.

recorded in its entirety. Next time make

sure you have enough time on the tape to

record the entire programme.