TV/VCR COMBO
USER’S GUIDE
FOR MODEL
TV-20240
(MONO)
(Illustration of TV-20240 and RM-C139)
IMPORTANT NOTE TO THE CUSTOMER:
Enter the serial number for your television
(located on the rear of the television cabinet) on the space below.
Staple your sales receipt or invoice to the inside cover of this guide.
Keep this user’s guide in a convenient place for future reference.
Keep the carton and original packaging for future use.
Serial Number
Download from Www.Somanuals.com. All Manuals Search And Download.
6 If an outside antenna is connected to the TV set, be sure the
antenna system is grounded so as to provide some protection
against voltage surges and built-up static charges. Section 810
of the National Electrical Code provides information with respect
to proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit, size
of grounding conductors, location of antenna discharge unit,
connection requirements for the grounding electrode.
13 For added protection of the TV set during a lightning storm or
when the TV set is to be left unattended for an extended period
of time, unplug it from the wall outlet and disconnect the
antenna. This will prevent damage to product due to lightning
storms or power line surges.
14 A TV set and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause
the TV set and cart combination to overturn.
7 An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power
lines or circuits as contact with them might be fatal.
SERVICE
15 Unplug this TV set from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the TV set.
C. If the TV set has been exposed to rain or water.
D. If the TV set does not operate normally by following the
operating instructions. Adjust only those controls that are
covered in the operating instructions as improper adjust-
ment of other controls may result in damage and will often
require extensive work by a qualified technician to restore
the TV set to normal operation.
8 TV sets are provided with ventilation openings in the cabinet
to allow heat generated during operation to be released.
Therefore:
E. If the TV set has been dropped or damaged in any way.
F. When the TV set exhibits a distinct change in perfor-
mance — this indicates a need for service.
— Never block the bottom ventilation slots of a portable TV
set by placing it on a bed, sofa, rug, etc.
— Never place a TV set in a “built-in” enclosure unless
proper ventilation is provided.
16 Do not attempt to service this TV set yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service personnel.
— Never cover the openings with a cloth or other material.
— Never place the TV set near or over a radiator or heat registe.r
9 To avoid personal injury:
17 When replacement parts are required, have the service
technician verify in writing that the replacement parts he uses
have the same safety characteristics as the original parts.
Use of manufacturer’s specified replacement parts can
prevent fire, shock, or other hazards.
— Do not place a TV set on a sloping shelf unless properly secured.
— Use only a cart or stand recommended by the TV set
manufacturer.
18 Upon completion of any service or repairs to this TV set,
please ask the service technician to perform the safety check
described in the manufacturer’s service literature.
— Do not try to roll a cart with small casters across thresh-
olds or deep pile carpets.
— Wall or shelf mounting should follow the manufacturer’s
instructions, and should use a mounting kit approved by
the manufacturer.
19 When a TV set reaches the end of its useful life, improper
disposal could result in a picture tube implosion. Ask a
qualified service technician to dispose of the TV set.
USE
20 Note to CATV system installer.
10 Caution children about dropping or pushing objects into the TV set
through cabinet openings. Some internal parts carry hazardous
voltages and contact can result in a fire or electrical shock.
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry
as practical.
11 Unplug the TV set from the wall outlet before cleaning. Do
not use liquid or an aerosol cleaner.
12 Never add accessories to a TV set that has not been designed for
this purpose. Such additions may result in a hazard.
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS ABOUT VIDEO
Before operating the video unit, please read the precautions on this page.
Precautions About Moistur
e
Precautions for Recording TV
Condensation
Programs
What is Moisture Condensation?
When you put cold water into a glass, water droplets
form on its surface. This phenomenon is called
moisture condensation.
If Moisture Condensation Occurs
The video unit may fail to operate, or may operate
erratically potentially damaging the unit and video
cassettes.
When Does Condensation Occur?
• When equipment is moved from a colder to a
warmer place.
About Copyright
The recordings you make from TV programs or pre-
recorded tapes cannot be used without permission
from the copyright holders, except when they are
used solely for personal enjoyment.
Trial Recording Before Making Important
Recordings
Make a trial recording before an important program
to be sure that you can record and playback audio
and video properly.
• Immediately after a room heater is started.
• When the unit is exposed to a cold air flow (like
from an air conditioner)
• In high humidity or when steam is present.
To Prevent Condensation
• Wait about an hour before operating the unit so
that it can become accustomed to the room
conditions.
Disclaimer:
JVC assumes no liability for failure to record or
playback audio and video properly with this unit.
Precautions About Video Cassettes
Keep these points in mind while working with video
cassettes.
Recording
• Provide proper ventilation.
• If you record on a previously recorded tape, the
original content will be automatically erased.
• Video cassettes cannot be reversed or “flipped
over” like audio cassettes.
If the unit fails to operate or operates poorly and you
think condensation may be the cause, turn the unit’s
power off and wait a few hours before trying to
operate the unit again.
Handling Cassettes Properly
• To store cassettes, place them inside their cases.
The cases should then be stored vertically.
• Do not drop cassettes, or give them any other
hard shock.
• Rewind cassettes before storing.
• Do not repeatedly load and unload tapes without
running them in between.
Do Not Store in the Following Places
• Exposed to direct sunlight or near a heating
device.
• Exposed to excessive humidity, smoke, or dust.
• Near a strong magnet (including speakers).
Enjoying Clear Video
Cleaning the Video Heads
After a long, or frequent use, the video heads inside
the unit may become dirty, possibly resulting in poor
picture quality. To prevent this from happening, it is
recommended you clean the unit frequently with a
head cleaning cassette (TCL-2 or 3, sold
separately).
If Video Quality is Still Poor After Cleaning
Try cleaning the unit two or three times instead of
just once. If the repeated cleaning still fails to
produce better picture quality, an internal
malfunction may be the cause. Call your local dealer
for servicing.
Prevent Accidental Erasur
e
Remove the small plastic tab at the rear of the
cassette. Without this tab, the cassette cannot be
used for recording. It is recommended that you
remove the tabs from important cassettes to prevent
accidental erasure. To record on a cassette whose
tabs have ben removed, cover the tab hole with two
layers of adhesive tape.
Video Heads beginning to get dirty
Video Heads totally clogged
Video Heads now fairly dirty
Download from Www.Somanuals.com. All Manuals Search And Download.
T A B L E O F C O N T E N T S
4
TABLE OF CONTENTS
VCR Menu
CONNECTIONS
Regular VCR Programming. . . . . . . . 20
Recording Speed. . . . . . . . . . . . . . 21
Auto SP→EP . . . . . . . . . . . . . . . . 21
Repeat Play. . . . . . . . . . . . . . . . . 21
Connections Checklist . . . . . . . . . . . . . . . . 5
Front Panel Diagram . . . . . . . . . . . . . . . . . 5
Cable Box Connection . . . . . . . . . . . . . . . . 6
Connecting to a Camcorder . . . . . . . . . . . . . 7
Connecting to Headphones/Earphones . . . . . . . 7
V. Stabilizer. . . . . . . . . . . . . . . . . 21
+
VCR Plus
+
Recording with VCR.Plus . . . . . . . . . 22
Timer recording Troubleshooting. . . . . . . . . . 23
Instant Timer Recording
GETTING STARTED
Remote Control . . . . . . . . . . . . . . . . . . . . 8
Power . . . . . . . . . . . . . . . . . . . . . . . . . 9
Adjusting Volume . . . . . . . . . . . . . . . . . . . 9
Changing Channels . . . . . . . . . . . . . . . . . . 9
Remote Programming . . . . . . . . . . . . . . . 10
CATV & Satellite Codes . . . . . . . . . . . . . . . 10
ITR. . . . . . . . . . . . . . . . . . . . . . 23
BUTTON FUNCTIONS - TV
Display . . . . . . . . . . . . . . . . . . . . . . . . 24
Video Status . . . . . . . . . . . . . . . . . . . . . 24
Sleep Timer . . . . . . . . . . . . . . . . . . . . . 24
Number Buttons (10 Key Pad) . . . . . . . . . . . 25
100+ . . . . . . . . . . . . . . . . . . . . . . . . . 25
Muting . . . . . . . . . . . . . . . . . . . . . . . . 25
Menu Button . . . . . . . . . . . . . . . . . . . . . 25
Input. . . . . . . . . . . . . . . . . . . . . . . 25
Return. . . . . . . . . . . . . . . . . . . . . . . . . 25
Exit. . . . . . . . . . . . . . . . . . . . . . . . . . 25
Closed Caption. . . . . . . . . . . . . . . . . . . . 25
Channel +/-. . . . . . . . . . . . . . . . . . . . . . 25
Volume +/-. . . . . . . . . . . . . . . . . . . . . . 25
TV/CATV Switch. . . . . . . . . . . . . . . . . . . 25
MENU FUNCTIONS
Using the Menu . . . . . . . . . . . . . . . . . . . 11
Initial Setup
Auto Tuner Setup. . . . . . . . . . . . . . 12
Channel Summary. . . . . . . . . . . . . 12
Set Lock Code . . . . . . . . . . . . . . . 13
VCR Plus+ Guide Setup. . . . . . . . . . 14
Picture Settings
Tint . . . . . . . . . . . . . . . . . . . . . 15
Color . . . . . . . . . . . . . . . . . . . . 15
Picture
Bright
Detail
. . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . 15
BUTTON FUNCTIONS - VCR
Sound Settings
VCR Basics . . . . . . . . . . . . . . . . . . . . . 26
Index Search . . . . . . . . . . . . . . . . . . . . 26
Tracking Adjustment. . . . . . . . . . . . . . . . . 26
Skip Search . . . . . . . . . . . . . . . . . . . . . 27
Re-View . . . . . . . . . . . . . . . . . . . . . . . . 27
EZ Ject . . . . . . . . . . . . . . . . . . . . . . . . 27
Shuttle Plus +/- . . . . . . . . . . . . . . . . . . . 27
Timer. . . . . . . . . . . . . . . . . . . . . . . . . 27
VCR Plus+. . . . . . . . . . . . . . . . . . . . . . 27
Daily/Weekly. . . . . . . . . . . . . . . . . . . . . 27
REC/ITR . . . . . . . . . . . . . . . . . . . . . . . . 28
STOP/EJECT . . . . . . . . . . . . . . . . . . . . . . 28
Program Check . . . . . . . . . . . . . . . . . . . 28
Bass . . . . . . . . . . . . . . . . . . . . . 16
Treble . . . . . . . . . . . . . . . . . . . . 16
Balance . . . . . . . . . . . . . . . . . . . 16
MTS (Multi-channel TV Sound) . . . . . 16
Some Sound Advice . . . . . . . . . . . . 16
Clocks/Timers
Set Clock (Semi-Auto). . . . . . . . . . . 17
Set Clock (Manual). . . . . . . . . . . . . 17
On/Off Timer. . . . . . . . . . . . . . . . . 18
General Items
Language . . . . . . . . . . . . . . . . . 18
Closed Caption. . . . . . . . . . . . . . . 18
VCRNFoiUseNMuCtinTgI.O. N. .S. . . . . . . . . . . . 18
APPENDICES
VCR Basics
Troubleshooting . . . . . . . . . . . . . . . . . . . 29
Limited Warranty . . . . . . . . . . . . . . . . . . . 31
Authorized Service Centers . . . . . . . . . . . . . 32
Memo. . . . . . . . . . . . . . . . . . . . . . . . . 33
Specifications . . . . . . . . . . . . . . . Back Cover
Load Videocassette . . . . . . . . . . . . 19
Find the Start of the Program. . . . . . . . 19
Start Playback. . . . . . . . . . . . . . . . 19
Stop Playback. . . . . . . . . . . . . . . . 19
Simple Recording. . . . . . . . . . . . . . 19
Tape Counter. . . . . . . . . . . . . . . . 19
Ejecting the Cassette. . . . . . . . . . . . 19
Download from Www.Somanuals.com. All Manuals Search And Download.
5 C O N N E C T I O N S
CONNECTIONS CHECKLIST — READ ME FIRST!
The Connections Checklist — Read Me First! section of this guide is a list of ideas to keep in mind
when you set out to perform your connections. It is designed to help us not-so-technically-
advanced individuals. If you read this section, and can’t identify the plugs, connectors, and
components you have, do not be afraid to seek help.
1) Always refer to the connection instructions in the user’s
A/V input plug
guide for your components first! The manufacturer will
provide the most detailed information about their products.
2) Know your jacks and plugs — most are color coded:
• Yellow plugs are Video connections
• Red plugs are Right Audio connections
• White or black plugs are Left Audio (Mono) connec-
tions (if your camcorder is a stereo model, use a
stereo-to-monaural conversion cable to connect to the
Combo unit. Conversion cables may be purchased
separately.)
RF Connectors
3) Perform one hookup at a time. If you have many
accessories to connect, make sure each connection is
correct by checking to see that it works properly before
attempting the next connection.
4) Unplug the power cord between each connection.
FRONT PANEL DIAGRAM
TV-20240 Front Panel
Download from Www.Somanuals.com. All Manuals Search And Download.
C O N N E C T I O N S
6
CABLE BOX CONNECTION
There are two basic types of antenna/cable hook-ups. They are easy to distinguish.
Type 1:
If you use an antenna or have a cable television system that does not require the use of a
decoder box to receive signals, use the diagram below to connect your TV/VCR combo.
1) Connect the cable or antenna wire out from the wall in to the TV VHF/UHF
input at the rear of the combo unit.
2) Plug the power cord into a nearby AC outlet.
Type 2:
If you use an cable box to access any or all channels, use the diagram below.
1) Connect the cable wire out from the wall in to the cable box RF input.
2) Connect an RF cable out from the cable box in to the TV VHF/UHF input.
3) Plug the power cord into a nearby AC outlet.
Download from Www.Somanuals.com. All Manuals Search And Download.
7 C O N N E C T I O N S
CONNECTING TO A CAMCORDER
You can connect a camcorder right to your TV/VCR combo using the input jacks located at the front of the unit.
1) Press on the PUSH mark on the front panel door to open it.
2) Connect a yellow video cable from the cam-corder output into the TV’s Video input jack.
3) Connect a white (or Black) Mono audio cable from the camcorder output into the TV’s audio input jack.
❒ Refer to the camcorder’s instructions for further information about the camcorder.
CONNECTING TO HEADPHONES/EARPHONES
You can connect earphones or headphones to your TV/VCR combo using the input jack at the front of the unit.
1) Press on the PUSH mark on the front panel door to open it.
2) Insert the earphone/headphone plug into the phones input jack.
❒ Refer to the headphones or earphones instructions for further information.
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D 8
REMOTE CONTROL
R
RM-C
TV-20240
M-C139
139
CHANGING THE BATTERIES
Be sure to use only size AA batteries.
Push down on the remote's back cover and slide
towards the bottom to remove it.
1
Insert the two supplied AA batteries, carefully noting the
“+” and “–” markings on the batteries and remote
control. To avoid a short circuit, insert “–” end first.
2
Snap the cover back into place.
3
❒ If the remote control acts erratically, replace the batteries.
Typical battery life is usually about one year.
❒ We recommend alkaline batteries for a longer battery life.
NOTE:
When you change the batteries, try to complete the task
within 3 minutes. If it takes longer than 3 minutes, the remote
control codes for your Cable box will have to be reset (page
10).
RM-C139
Download from Www.Somanuals.com. All Manuals Search And Download.
9
G E T T I N G S T A R T E D
POWER
❒ Press the POWER button on the remote control or the TV/VCR combo front panel. The On Timer
lamp will glow red.
❒ Make sure that the TV/CATV switch on the remote is set to TV. Switch to CATV only if you plan to
operate a cable box. If you switch to CATV you will not be able to operate the TV/VCR combo
functions with the remote, only the cable box functions!
❒ To turn the power off, press the POWER button again. The On Timer lamp will go out.
❒ The On Timer lamp will glow green when the On/Off Timer is set to yes, even when the TV power
is off.
ADJUSTING VOLUME
1
2
CHANGING CHANNELS
10 key direct access.
1
Press the numbers on the remote’s 10 key pad. For single-digit channel numbers press 0 then the
number. For channels above 100, press the 100+ button plus the 2-digit number.
CHANNEL –/+ button.
2
Press the CHANNEL –/+ button, to scan the channels in order.
❒ After you operate the Auto Tuner Setup (page 12), all of the blank, or empty, channels will be removed
from scanning so that there is no noise or channel snow when you scan, only active channels.
Return.
3
Press the RETURN button to return to the previous channel. First, select a channel
(game #1). Then, select another channel (game #2) with the 10 key pad and push the RETURN button
to flip directly back and forth.
Download from Www.Somanuals.com. All Manuals Search And Download.
R E M O T E P R O G R A M M I N G 10
SETTING THE CATV CODES
Many CATV brands have more than one code. If the first code in the list does not work, try the other codes
listed. If your CATV box does not respond to any of the codes listed for the manufacturer, use the remote
control for theCATV box to operate it.
CABLE BOX OR SATELLITE SETUP
The remote is programmed with the CATV and Satellite codes for power on and off, 10 key, and channel up
and down.
1) Determine the correct code from the “CATV & Satellite Codes” chart below.
2) Slide the 2-Way Mode Selector Switch to CATV.
3) Press and hold down the DISPLAY button.
4) Enter the 3-digit code with the 10 key pad while continuing to hold down the DISPLAY button.
5) Release the DISPLAY button.
6) Confirm the operation of the cable box.
CATV & Satellite Codes
CABLE BOXES
CODES
CABLE BOXES
CODES
CABLE BOXES
CODES
Memorex
Movietime
007
Starquest
Sylvania
Tandy
004
019 035
062
074 054
092 077
032 040 042 078 094
018 019 035
033 034 048 049 001 042
091 073
ABC
035 001 011 002 009 033 091
055
044
029 001 044 088 091 063 042
030 052 076
082
082
029 001 044 088 091 076
063 044 042 030 052 088
063 044 042 030 052 088
063 044 042 030 052 088
023
032 039 029 042 044 088 040
038 060
038 040 032
011 046 010 012 047
016 017
007
Antronix
Archer
NSC
Oak
Panasonic
Paragon
Philips
Pioneer
Popular Mechanics 059
Pulsar
Quest
Teknika
Telecaption
Teleview
Texscan
Tocom
Belcor
Cable Star
Cabletenna
Cableview
Century
Citizen
Colour Voice
Comtronice
Contec
013 020 023 024 096 030 084
005 006 078
Toshiba
Tusa
TV86
Uniden Satellite 065 069
Unika
036 007 066 070
004
040
063 044 042 030 052 088 007
001 002 003 004 034 055 083
085 091 093 095
016 017
042 021
010
RCA
029 001 044 088 091 063
Realistic
Recoton
Regal
Regency
Rembrandt
051 044 088 053
059 063 044 042 030 052 088
014 041
028 099
042 030 052 076
011
001
042 043 044 052 063 088
082
Curtis
Diamond
Drake
008 009 056 061 087 090
029 001 044 088 091 076
037 067 071
013 022 058 062 020 040 026
021
United Artists
United Cable
Universal
Eagle
032 039 029 042 044 088 002
060
007
068 072
Videoway
Vid Tech
Vidter
007 050 023 045
064
064
Eastern
Focus
028 099
059
Runco
Salora
GC Electronics 063 044 042 030 052 088 082
Samsung
016 017 006 032 040 042 078
094
Viewstar
013 022 058 062 020 040
026 021
007 050 023 075
059
Gemini
GeneralElectric
General
Instruments 001 002 003 004 034 055 083
085 091 093 095
Gerrard
Hamlin
Hitachi
Hytex
004 085 032 030
057
Scientific Atlanta 008 009 056 061 087 090
Sheritech
Signal
Zenith
Zentek
027
013 022 058 062 020 040 026
004 042 032 078 094 021 038
002
032 040 042 078 094 063 044
030 052 088
063 044 042 030 052 088
014 015 028 041 099
031 079 002 080
011
001 002 003 004 034 055 083
085 091 093 095
031 079 080
SATELLITE
CODES
Signature
SL Marx
RCA
Sony
Gradiente
097
098
100
Sprucer
Standard
Components
016 017
Jerrold
032 039 029 042 044 088 018
060 063 052 030
001 004 055
032 040 042 078 094 004 063
044 030 052 088
Macom
Magnavox
Matsusita
025 026 013
016 017
Starcom
Stargate
Download from Www.Somanuals.com. All Manuals Search And Download.
1
1 U S I N G T H E M E N U
VCR SETUP SETTINGS
USING THIS GUIDE:
Throughout this guide there are certain symbols we use
as shorthand to show you what to do. When you see
them, keep these factors in mind:
Up and down arrows mean press the MENU UP or
MENU DOWN buttons. Pressing the up or down
buttons allows you to:
• Move vertically in the main menu screen
• Move through a submenu, or
• Move to the next letter, number, or other
choice in a submenu, or
• Back up to correct an error
PICTURE SETTINGS
Left and right arrows mean press the MENU LEFT or
MENU RIGHT button to:
• Select the highlighted item, or
• Select the options in a submenu
The “Press Button” means you should press
that button on the remote control
The “Helping Hand” points to the highlighted or
selected item in a menu.
SOUND SETTINGS
❒
Important information, or a note, about a feature
follows a cube like this one.
SMALL CAPITAL LETTERS are used when we refer
to buttons … this is important because some
menu functions have the same name.
THE ONSCREEN MENUS:
To bring up the onscreen menu, press the MENU
button on the remote, and the menu will appear on the
screen. The "Helping Hand" will appear next to an item
that is selected.
TIMER SETUP ITEMS
When you first turn on the TV, the “Picture Settings”
menu will appear. However, “Initial Setup” is so
important, that this guide begins here.
INITIAL SETUP ITEMS
GENERAL ITEMS
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
I N I T I A L S E T U P
CHANNEL SUMMARY
AUTO TUNER SETUP
NOTES:
You can add or delete channels from
channel scanning. You can also lock
out any “unauthorized” viewers from
one or up to all 181 channels.
During Auto Tuner Setup, the TV will
automatically scan through all available
channels and memorize the active ones
so that when you scan, you do not pick
up weak or noisy channels.
During Initial Setup,
the TV will be
programmed to
only receive active
channels. Once the
channels are
activated by the
Auto Tuner Setup
they will be includ-
ed in Scan.
Press any MENU Button
To CHANNEL SUMMARY
To operate
Press any MENU button
To AUTO TUNER SETUP
To operate
Note: Noise Muting will not work while
you are in the Channel Summary menu
Some weak
channels may be
included or omitted
during this
TUNER MODE
:
CABLE AIR
.
START
procedure. You can
add or delete any
channels from
scanning in the
Channel Summary.
SCAN
To choose CABLE or AIR
To move to START
You can manually set channels to scan
that were too weak to be picked up
during Auto Tuner Setup. Conversely, if a
channel was too weak to receive a good
picture but was picked up anyway, delete
it by removing the Ö. (If you have not
performed the Auto Tuner Setup
described in the previous column, please
do so now.)
To start Auto Tuner Setup
NOW
PROGRAMMING!
48
The Programming takes approximately
1 to 2 minutes
CHNO.
01
SCAN
CH NO. SCAN
PROGRAMMING OVER!
06
07
08
09
10
Ö
02
Ö
Ö
Ö
Ö
Note: Noise Muting will not work while
Auto Tuner Setup is working.
03
04
Ö
Ö
05
CHANNEL -/+ to select the channel
To the SCAN column
To add or delete from scan
EXIT when finished
Note: Channels set to scan will be
marked with an Ö.
Note: Some cable systems experience
interference from radio frequencies on
Cable Channel 95. If you like, you can
delete this channel from scanning by
removing the Ö
Continued next page ...
Download from Www.Somanuals.com. All Manuals Search And Download.
3
1 I N I T I A L S E T U P
CHANNEL GUARD - LOCK
SET LOCK CODE
The Lock Code locks and unlocks
Channel Guard settings. Write this four
digit number down and keep it safe
from potential viewers!
To CHANNEL SUMMARY
To operate
CHANNEL +/- to select the channel
To the Lock column
Press any MENU button
To SET LOCK CODE
To operate
The access code zero (0) to lock
or unlock that channel
CHNO.
01
SCAN
CH NO. SCAN
06
07
08
09
10
Ö
The padlock icon appears
02
Ö
Ö
Ö
Ö
ZERO (the access code is zero)
03
04
Ö
Ö
05
LOCK CODE
0000
FINISH
EXIT when finished
To choose the number
Note: When viewing, once the Channel
Guard for a specific channel has been
unlocked, that channel will remain
unlocked until power to the television is
turned off. To reactivate Channel Guard,
turn the power off and then on again.
To move to the next place
Continue to follow these directions for
all four numbers
To FINISH
To save settings and exit
EXIT when finished
CHANNEL GUARD MESSAGE:
This message appears when a viewer
attempts to watch a guarded channel:
Note: If you forget your Lock Code
you can check your code by going to
the setup screen of the Set Lock Code
function.
PLEASE ENTER LOCK CODE BY
10 KEY PAD TO UNLOCK IT.
NO. ––––
Note: After a power interruption of
more than 90 seconds you must reset
the lock code.
To watch a channel you have locked, enter
the lock code using the 10 key pad. An
explanation of how to set the lock code
appears in the next column on this page.
If the wrong lock code is entered, this
message will flash on the screen:
INVALID LOCK CODE !
Download from Www.Somanuals.com. All Manuals Search And Download.
1
4
I N I T I A L S E T U P
+
+
VCR PLUS GUIDE SETUP
VCR PLUS GUIDE SETUP
Continued...
NOTES:
Below is the VCR Plus+ Guide Setup
Menu
You may simplify the recording of
television programs by using VCR
PLUS codes to program your VCR.
Whenever you want to record a
program, all you need to do is find the
VCR PLUS+ code for that program.
After entering the code, the TV/VCR
Combo. will automatically record the
program at the correct date, time, and
channel.
+
VCR PLUS codes
for individual televi-
sion programs can
be found in most
local newspaper
television listings
and TV magazines.
+
Before using VCR PLUS+ for the first
time, you need to set local channels
+
for VCR Plus . These guide numbers
To move to a TV CH position
which corresponds to a
may be found in your local TV
magazine or newspaper’s TV listings.
particular GUIDE CH number
To Select a receivable TV CH
To Set Local Channels for VCR
PLUS+
Repeat the steps described above
until all receivable channels have
been set.
Press any of the menu buttons
to display the Initial Setup
screen
EXIT to save settings and exit.
Your TV/VCR Combo is now ready to
accept VCR Plus+ codes.
To Select SET VCR PLUS+
GUIDE CHANNEL
+
To display the SET VCR PLUS
GUIDE CHANNEL menu
screen
Download from Www.Somanuals.com. All Manuals Search And Download.
5
1
P I C T U R E S E T T I N G S
TINT
BRIGHT
NOTES:
Adjust the degree of light and dark in
the picture.
Tint allows you to adjust the levels of
red and green in the picture.
If you do not move
to the next setting
with the up and
down arrows, in
approximately three
seconds the screen
will disappear and
your preferences
will be stored.
Press any MENU button
To TINT
Press any MENU button
To BRIGHT
To accentuate green
To lighten the picture
To darken the picture
To move to the next or previous
To accentuate red
To move to the next
You can exit the
Picture Settings
menu at any time
by pressing the
EXIT button on the
remote control.
COLOR
DETAIL
Color allows you to adjust both the
vividness and subtlety of the color.
Detail allows you to adjust the level of
detail within the picture.
Press any MENU button
To COLOR
Press any MENU button
To DETAIL
To make colors more vivid
To subdue colors
To make the picture sharper
To make the picture smoother
To move to the previous
To move to the next or previous
PICTURE
Picture allows you to adjust the range
between black and white in the
picture.
Press any MENU button
To PICTURE
To increase contrast
To decrease contrast
To move to the next or previous
Download from Www.Somanuals.com. All Manuals Search And Download.
1
6
S O U N D S E T T I N G S
BASS
MTS (Multi-Channel
NOTES:
The Bass level adjustment feature allows
you to raise or lower the level of lower
frequencies in the TV’s sound.
Television Sound)
MTS technology gives you a choice
among stereo, mono, and Second
Audio Programs (SAP).
MTS has no effect
on normal sound
broadcasts.
Press any MENU button
To BASS
You can exit the
Sound Settings
menu at any time
by pressing the
EXIT button.
Press any MENU button
To MTS
To emphasize bass
To reduce bass
To move to next
TREBLE
Select the mode
The Treble level adjustment feature
allows you to raise or lower the level of
higher frequencies in the TV’s sound.
(The ON AIR arrow tells you if
the current signal contains
Stereo or SAP)
Press any MENU button
To TREBLE
Note: Keep the TV in STEREO mode
to get the fullest sound quality.
To increase treble
To decrease treble
To move to next
Note: SAP will allow you to hear an
alternative soundtrack, if available.
Note: Choose MONO to reduce
excess noise in a program or channel.
BALANCE
The Balance adjustment feature
allows you to center the TV’s sound to
your needs.
Press any MENU button
To BALANCE
To shift the speaker balance to
the right
To shift the speaker balance to
the left
To move to next
Some Sound Advice
You can tell if a program is broadcast in stereo by the position of the ON AIR arrow in the MTS
menu. Unfortunately, it is common for some cable companies to squash the transmission of
stereo programs to mono because they only have mono equipment. If connected to a cable
system, the sound is at the mercy of that cable company — if they broadcast in mono, you
receive mono sound regardless of the original stereo programming.
Fortunately, most programs that are broadcast in stereo are aired on the major television
networks. If you connect your TV to an antenna instead of cable, and set the tuner mode in the
Auto Tuner Setup to “Air” instead of “Cable,” you will be able to pick up stereo broadcasts in
stereo.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
1 C L O C K S / T I M E R S
SET CLOCK (SEMI-AUTO)
SET CLOCK (MANUAL)
NOTES:
The Clock is the heart of all timer
If you are in an area that does not
receive the EDS or XDS signal needed
for the Set Clock (Semi-Auto) function,
or if you wish to set the clock to a
different time, use the manual function.
To use the Semi-
functions. You must set the clock before
any timer functions will work. Your clock
can be set automatically by using a
broadcast signal available in most areas.
Auto function, first
tune the television
to your local PBS
station. PBS
stations transmit the
EDS or XDS signal
needed to set the
clock..
Press Channel +/- to go to your
local PBS station (These stations
carry the EDS or XDS time signal)
Press any MENU button
To SET CLOCK
To operate
DAYLIGHT
SAVINGS TIME
Press any of the Menu .
To choose MANUAL
To SET CLOCK
To operate
This function
automatically
adjusts for Daylight
Savings time. At
2:00 am on the first
Sunday in April, the
clock moves
To choose SEMI-AUTO
forward one hour.
At 2:00 am on the
last Sunday in
October the clock
moves back one
hour.
To move to hour
To set the hour (AM/PM)
To move to minutes
To set the minutes
To move to month
To set the month
POWER OUTAGE
To move to time zone
To set the time zone
If the TV is
unplugged or you
experience a power
outage of more
than 90 seconds,
you must reset the
clock in order for
any of your timer
functions to work.
To move to D.S.T. (Daylight
Savings Time)
To move to date
To set the date
To turn D.S.T. ON or OFF
To move to FINISH
To move to year
To set the year
To exit and save settings
If power is interrupt -
ed for less than 90
seconds, the clock
will continue to run,
but will be delayed
the length of the
power interruption
(for example if the
power was
To move to D.S.T.
To turn D.S.T. ON or OFF
To Move to START CLOCK
To start the clock
CLOCK SET MESSAGE
If you do not set the clock but attempt to
use a timer function anyway, you will get
the following message:
THANK YOU !!
PLEASE SET CLOCK FIRST!!
interrupted for 45
seconds, the clock
will be 45 seconds
slow). It is best to
check the clock
If you want to synchronize the TV
clock with another clock or time signal,
press LEFT or RIGHT MENU arrow at the
appropriate time, and the clock will start
at that moment.
MODE
TIME
DATE/ YEAR
D.S.T.
SEMI-AUTO MANUAL
--:-- --
---/ --/ --
ON OFF
START CLOCK
after any interrup -
tion in power.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
T I M E R S / G E N E R A L I T E M S 8
ON/OFF TIMER
LANGUAGE
NOTES:
Choose from English, French, or Spanish
on-screen menus and displays.
Use the On/Off Timer as an alarm to
wake up, as a program reminder, or as
a decoy when you’re out of the house.
Closed Caption
Notes: Captions
are usually found
on CC1 and text
on T1. The other
caption and text
channels are
Press any MENU button
To LANGUAGE
Press any MENU button
To ON/OFF TIMER
LANGUAGE
ENG
FRE
SPA
workable but are
for future purpos-
es. If you want to
view captions or
text, most likely
you should
choose CC1 for
Captions and T1
for Text.
To operate
To choose a language
EXIT when finished
ON TIME
7 : 00 PM
10 : 00 PM
02
OFF TIME
CHANNEL
MODE
ONCE EVERYDAY
YES NO
ON/ OFF TIMER
CLOSED CAPTION
If they are included in a program, you can
view closed captions or text information.
FINISH
To access a
To set the hour (AM/PM) you
want the TV to turn on
captioning option
or to turn one off,
allow the display
to remain on
Press any MENU button
To CLOSED CAPTION
To operate
To move to minutes
To set the minutes
screen until it
To accept ON TIME and to
move to OFF TIME (set time for
TV to turn off)
disappears. In a
few seconds, the
captions will start.
CAPTION: CC1 CC2 CC3 CC4
TEXT
:
T1 T2 T3 T4
FINISH
To move to CHANNEL
If a large black
box covers 80%
of the screen, the
Text Mode is
probably "On".
Press the CLOSED
CAPTION button to
turn it off.
To select channel
To move to MODE
TO CAPTION or TEXT
To select a caption or text channel
TO FINISH
Choose ONCE or EVERYDAY
To YES NO
To save settings and exit
Choose YES for on, NO for off
To FINISH
Note: See page 25 for details on accessing
closed captions with the CLOSEDCAPTIONbutton
on your remote control.
General Note:You
can exit the menu
at any time by
pressing the EXIT
button.
To save settings
EXIT when finished
Note: Closed captioning may not correctly
operate when the signal received is weak
or when you are playing a video tape.
Note: In order for ON/OFF Timer to
work, the clock must be set. After a
power interruption of more than 90
seconds timer settings will be turned off
and will need to be reset.
NOISE MUTING
Eliminates noise from channels that are
not broadcasting or are too weak.
Note: ON/OFF Timer cannot be set to
Press any MENU button
To NOISE MUTING
To turn ON/OFF
locked or guarded channels.
Note: Noise Muting will not work when
you operate Auto Tuner Setup or Channel
Summary.
Download from Www.Somanuals.com. All Manuals Search And Download.
19 B A S I C V C R F U N C T I O N S
STOP PLAYBACK
VCR BASICS
NOTES:
To end playback of the video
cassette, press the STOP button on
the remote or the STOP/EJECT button
on the TV/VCR combo front panel.
The video playback will stop and the
on screen display will automatically
switch to the television (or to LINE if
LINE INPUT is selected).
This section of the guide will explain
the many functions of the VCR
portion of your new TV/VCR Combo.
We will begin with a basic explana-
tion of how to load, view and eject a
video cassette.
The TV/ VCR combo
can record and play
back video
cassettes in
monaural sound
only.
This TV/VCR combo
is equipped with
SQPB (S-VHS
QUASI PLAYBACK)
which lets you
watch tapes record-
ed in the S-VHS
format.
LOAD A VIDEOCASSETTE
Make sure the “window” of the video
cassette is facing up, and the rear
label of the video cassette is facing
you. Insert the cassette into the slot
below the television screen by
pressing on the rear of the cassette.
Do not use too much pressure when
inserting. If the tab at the rear of the
cassette has been removed,
SIMPLE RECORDING
To record a television program, first
select the channel airing the program
you wish to record using the 10-digit
key pad or CHANNEL +/- buttons on
the remote control. Next, press the
SP/EP button to select the recording
speed (for more on recording speeds
see page 20). To begin recording,
press the PLAY button while holding
down the REC button.The following
display will appear on screen over
the television picture for a few
seconds.
SQPB does not
deliver S-VHS
resolution.
S-VHS recording is
not possible with
this video recorder.
playback of the tape will begin
automatically:
You can watch a
different program
than the one being
recorded by the
CAUTION!
To avoid injury, do not place
your hand inside the video
cassette slot of the VCR or your
hand may be caught by the
unit’s internal mechanism. Take
special care to prevent children
from inserting their hands into
the VCR.
VCR. Press the
CHANNEL +/- button
or use the 10-key
pad to switch to a
different channel.
You may also return
to the recording
Channel/Rec.
Display
REC 22
Tape Counter
channel at any time.
COUNT 0:00:30
FIND THE START OF THE
PROGRAM
When the program is over, press STOP
to finish recording.
If the tape is not set at the start of the
program, you can move backwards
on the tape by using the REW button
on the remote or TV/VCR combo front
panel. Press REW to rewind the tape
to the desired point. To advance
forward on the tape, press the FF
button.
TAPE COUNTER
The Tape Counter appears on screen
when you fast forward or rewind as a
guide to show how much tape is left
on a cassette. It also appears when
you begin recording or playback. To
see the tape counter display at other
times, press DISPLAY. For more on
DISPLAY, see page 24. To reset the
counter, press CANCEL on the remote.
START PLAYBACK
To begin viewing a video cassette,
press the PLAY button on the remote
or on the TV/VCR combo front panel.
A video picture will appear.
EJECTING THE CASSETTE
To remove a cassette from the unit,
press the STOP/EJECT button on the
TV/VCR combo front panel. The...
mark will begin to flash and the
cassette will be ejected from the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
V C R M E N U I T E M S
VCR MENU
To CHANNEL
NOTES:
Recording
The VCR Menu screen gives you a
number of options for operating your
VCR. For an explanation of how to
use on screen menus, see page 11.
*Press any of the MENU buttons to
display the menu screen.
To select the channel of the
program you wish to record.
To RECORDING SPEED
speeds
This VCR allows for
recording and
playback at two
different tape
speeds.
To select the recording
speed.
• SP - select to record at standard
speed.
REGULAR VCR PROGRAMMING
This function lets you manually input
the time, date and channel informa-
tion for a program you wish to
record. (To program your VCR using
VCR Plus+ codes see page 22)
To REGULAR VCR
SP - Standard Play.
This setting gives
the best recording
and playback
qualities. It is the
time length indicat-
ed on blank video
cassettes.
• EP - select to record at 1/3 normal
speed.
To move to FINISH
To exit programming and
save your settings. The
following message will
appear:
PROGRAMMING
EP - Extended Play
This setting records
and plays back at
1/3 the SP speed
(for example a 120
minute cassette can
record for six hours
at the EP setting).
However, video and
audio quality at EP
speeds are not as
good as those
YOUR PROGRAM IS CONFIRMED
PUSH THE TIMER BUTTON
The TIMER button on the
remote control. The timer is
now in standby
The REC lamp will glow green on the
front panel of the unit, indicating the
timer has been programmed. When the
programmed start time arrives, the REC
lamp will glow red and recording will
begin. When the programmed stop time
arrives, the lamp will go out and the
recording will automatically stop.
recorded at SP
speeds.
To operate
OtherVCR Notes:
To check your
programmed
The following menu will appear.
settings press the
PROG. CHECK button
on the remote
control. See page
28 for more details.
Note: After recording if there are other
pre-set programs the lamp will turn green.
Notes on overlapping programs:
If the timer is set to record two different
programs with overlapping times, the
second recording will not start until the first
is finished. For example if one timed
recording is set to run from 5:00 to 6:00,
and a second is set from 5:30 to 7:00, the
second recording will not start until 6:00
when the first finishes. If one program
entirely overlaps another - program 1 is
from 5:00 to 6:00, program 2 is from 5:30
to 6:00 - the second program will not
record.
For troubleshooting
on Timer Recording
see page 23.
To select DATE
To START (hour AM/PM)
To set the time you wish the
VCR recording to begin.
• When you press the Right
or Left arrow button, the
current time is first displayed.
To STOP
To set the time you wish the
VCR recording to end
Download from Www.Somanuals.com. All Manuals Search And Download.
21 V C R M E N U I T E M S
RECORDING SPEED
REPEAT PLAY
Select the speed at which you
would like to record SP (standard
play) or EP (extended play)
Once playback of a cassette has
finished, this function automatically
rewinds the tape and begins
playback again. Playback may be
repeated up to 50 times.
Press any MENU button to
display the VCR menu
screen.
Press any MENU button to
display VCR Menu screen
To RECORDING SPEED
To set to SP or EP
To REPEAT PLAY
Press EXIT to finish
To turn Repeat play ON or
OFF
ON: Once a tape has finished it
will automatically rewind
and replay
OFF: Tape will stop when
playback is completed.
AUTO SP➔EP
This function is used with timer-
recording (pg 20 or pg 22) while in
the SP tape speed mode. The unit
automatically calculates the amount
of time left in the recording and the
amount of tape left on the cassette.
If there is not enough tape to finish
the recording, the unit automatically
switches to the EP mode to finish
the recording.
Press EXIT to finish.
Note: If a non-recorded period of
three seconds or more is encoun-
tered on a tape, playback will stop
and the tape will automatically
rewind. If you timer-record two
programs back-to-back, a non-
recorded period will automatically
be inserted between programs.
Press any MENU button to
display the VCR menu
screen.
To AUTO SP➔EP
V. STABILIZER
To set to ON or OFF
This function eliminates any vertical
shaking of the video image during
playback in EP mode.
ON: The unit will automatically
switch from SP to EP speed if
there is not enough tape left
on the cassette to finish the
recording.
OFF:The tape speed will not
change. The tape may run out
before recording is finished.
Press any MENU button to
display the VCR menu
screen.
To V. STABILIZER
To turn ON or OFF
Press EXIT to finish
Press EXIT to finish
Notes: Closed Captioning may not
display properly when V. Stabilizer
is set to "ON".
After a power interruption or once a
tape is ejected, V. Stabilizer will
return to "OFF".
Download from Www.Somanuals.com. All Manuals Search And Download.
+
22
V C R P L U S
VCR PLUS+
NOTES:
Press the DAILY/WEEKLY
Your TV/VCR Combo comes
equipped with VCR Plus+ technolo-
gy. This function allows you to
program your VCR simply by
entering the VCR Plus+ code number
associated with the program you
wish to record.
Note: Before VCR Plus+ can be
used, VCR Plus guide channels must
be programmed. See VCR Plus
Guide Setup in “Initial Setup” page
14, if you have not yet programmed
these channels).
button to select how often a
program should be recorded,
ONCE, DAILY, or WEEKLY
VCR Plus+
Codes
VCR Plus codes for
individual programs
may be found in
most local newspa-
per television
listings or in TV
magazines. VCR
Plus+ Codes are th
three to eight digit
number usually
shown after the title
or description of a
program in TV
Press the SP/EP button to
select SP or EP recording
speed. (See pg 20 for more
on tape recording speeds)
Press the VCR PLUS+ button
The following screen will appear,
displaying a summary of the informa-
tion you just entered:
listings.
DATE
MON - FRI
2:30 PM
3:00 PM
03
TIMER RECORDING WITH VCR
PLUS+
Press the VCR PLUS+ button
on the remote control
The VCR PLUS+ code screen appears
You can program
your VCR with up to
six events. These
events may be up t
a month in the
future. For more
information on
setting timer record
ings, see "Regular
VCR Programming"
on page 20.
START
STOP
CHANNEL
RECORDING SPEED
SP EP
IF ALL OK,
PUSH VCR PLUS+
CANCEL BY
CANCEL
- - - - - - - -
If the settings are correct, press the
VCR PLUS+ button again to accept. The
following message will appear:
ENTER THE PLUS CODE
Note:
VCR Plus+ and
PlusCode are
registered
YOUR PROGRAM IS CONFIRMED
PUSH THE TIMER BUTTON
Enter the VCR PLUS+ code (three-to-
eight digit number) of the show you
wish to record using the 10-key pad
on the remote control. The following
screen will appear:
trademarks of
Gemstar
If you wish to make a correction, use
Development
Corporation.
The VCR Plus+
system is manufac-
tured under license
from Gemstar
Development
Corporation.
the (
) buttons to move to the item
and the (
) buttons to correct. Once
corrected press VCR PLUS+ to accept
the settings.
1234
HOW OFTEN?
ONCE DAILY (M-F) WEEKLY
SELECT
Press the Timer button
on the remote control.The timer
is now in standby mode.
The REC lamp will glow green on the
front panel of the unit, indicating the
timer has been programmed. When the
programmed start time arrives, the
REC lamp will glow red and recording
will begin. When the programmed stop
time arrives, the lamp will go out and
the recording will automatically stop. If
there are other pre-set recordings the
REC lamp will glow green.
RECORDING SPEED
IF ALL OK,
PUSH VCR PLUS+
SP EP
CANCEL BY
CANCEL
Note: If you enter the VCR Plus+
code incorrectly, press CANCEL on the
remote. The first screen will
reappear.
Download from Www.Somanuals.com. All Manuals Search And Download.
23 T R O U B L E S H O O T I N G / I T R
TIMER RECORDING
INSTANT TIMER
TROUBLESHOOTING
The following are some common
problems/issues that may arise while
using Timer Recording.
RECORDING (ITR)
Instant Timer Recording allows you to set
the VCR timer after the videotaping of a
program has begun. The ITR timer can
be programmed to stop recording up to
four hours after it has begun.
To use the ITR timer, the VCR must
already be recording. Press the REC/ITR
button on the front panel of the VCR
(Note: This function cannot be accessed
with the remote control)
REC lamp starts flashing when you
press TIMER on the remote control.
No cassette is loaded into VCR.
Insert a cassette into VCR and
continue.
Cassette loaded has its recording tab
removed.
Insert a recordable cassette, or cover
the missing tab hole with two layers of
tape.
REC/ITR
The following display will appear on the
screen:
REC 22
The following message appears
when attempting to eject tape or
operate VCR:
ITR 0:30
VCR TIMER IS ON. PUSH
TIMER BUTTON TO RELEASE.
COUNT 0:00:01
Press the TIMER button and set Timer
Mode to Off. Try operating VCR again.
The timer above is set to stop recording in
30 minutes.
To stop taping once automatic
recording has begun.
Press the TIMER button, then the STOP
button.
Press the ITR button again to increase
the amount of time on the ITR timer. Each
press increases the amount by 30
minutes. The ITR timer can be set from a
minimum of thirty minutes "ITR 0:30" to a
maximum of four hours "ITR 4:00" When
the time allotted to the ITR expires, the
recording automatically shuts off.
Note: To cancel the ITR timer, press the
REC/ITR button until the on-screen display
disappears.
Note: To stop recording before the
allotted time expires, press the STOP
button.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
B U T T O N F U N C T I O N S - T V
BUTTON FUNCTIONS
VIDEO STATUS
NOTES:
This section will describe in detail the
different buttons on your remote
control and their functions. Buttons
related to the operation of the televi-
sion are listed first, followed by the
buttons used to operate the VCR. The
names of individual buttons in this
section are printed in SMALL CAPS.
The VIDEOSTATUSbutton gives your television
a movie theater-like quality with the “Cinema”
setting, raises the level of video game detail
with “Game” setting, or resets display to
factory settings with “Standard”.
Please note that if
the clock, Sleep
Timer, or On/Off
Timer are not set,
the initial Display
screen will state
“Clock Not Set,”
“Sleep Timer Off,”
and “On/Off Timer
Off,” respectively.
“Standard” resets the picture settings to
factory-set levels.
“Cinema” Gives a film-like look to televi-
sion and video programs
DISPLAY
The Display screen shows the current
status of timers and inputs.
Notes on Display:
"Remain"
automatically
calculates how
much time is
remaining on a
video cassette
inserted in the
unit. If the display
reads "--:--", run
the tape a little bit,
then try Display
again.
If there is no tape
inside the unit,
Remain will read
"--:--"
“Game” enhances the appearance of
video game graphics.
DISPLAY
VIDEO STATUS
07
CINEMA
GAME
STANDARD
NOW
12:20 PM
JAN/ 26/ 99
EP
SPEED
REMAIN
SLEEP TIMER
ON/ OFF TIMER
--:--
OFF
OFF
SLEEP TIMER
Sleep Timer turns off the TV for you in
case you fall asleep. Program it to work
in intervals of 15 minutes up to 180
minutes.
❑ The channel or AV input (Channel 07)
❑ Current time (12:20 PM)
❑ Current date (Jan. 26, 1999)
❑ Recording Speed (EP)
SLEEP TIMER
0 15 30 45 60 75 90 105 120 135 150 165 180
❑ Amount of tape remaining on video
cassette. (--:--)
❑ Sleep Timer status/minutes
remaining (OFF)
❑ On/Off Timer status (OFF)
SLEEP TIMER MESSAGE
20 seconds prior to the automatic
shut-off, this message will appear:
Each press of the DISPLAY button
changes the display mode:
GOOD NIGHT ! !
PUSH SLEEP TIMER BUTTON
TO EXTEND.
DISPLAY
TIME
CHANNEL
VCR OFF
Display shows the above menu screen.
Time shows only the current time over
the television picture. Channel shows
only the number of the channel the
television is currently tuned to. VCR
shows the VCR's current function (for
example - "Play") and tape counter.
You then have 20 seconds to press the
SLEEP TIMER button to delay turn off for
another 15 minutes.
Note: VCR display is only available
when there is a tape in the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
2
B U T T O N F U N C T I O N S - T V
NUMBER BUTTONS
RETURN
Return to the last channel viewed after
moving to another channel via the 10 key
pad.
10 KEY PAD
Press two of the number buttons to move to
single and double digit channels.
To move to Channel 7:
Move to another channel using the
10 key pad
0 (zero)
RETURN
7 (seven)
The TV will return to the first
channel
EXIT
100 +
The EXIT button lets you leave any menu
and return to normal television viewing.
The 100+ button accesses all channels
above Channel 99.
To move to Channel 124:
CLOSED CAPTION
View the closed captions or text when
included in a broadcast.
100+
CLOSED CAPTION
2 (two)
4 (four)
CC
TEXT
OFF
Note: For more information on Closed
Caption, see page 18.
MUTING
The MUTING button turns the sound off
completely when you press it.
Note: Closed captioning is not available on
video cassettes.
MUTING
CHANNEL +/-
The sound will turn off
completely.
The CHANNEL +/- button lets scan forward
and backwards through the available
television channels. For more on this
feature, see page 9.
Note: To return to the original volume
press MUTING again.
VOLUME +/-
The VOLUME +/- button raises or lowers the
volume. For more on this feature, see
page 9.
MENU BUTTONS (
)
Press any of the four menu buttons to
access the onscreen menu system.
TV/CATV SWITCH
For normal operation of your TV/VCR
combo, set the TV/VCR switch to "TV". If
you use a cable box to select channels,
set the switch to "CATV".
TV
LINE
Note: The VCR buttons will only work when
the remote is set to "TV". If you use the "CATV"
setting, you must switch to "TV" when you
wish to operate the VCR.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
B U T T O N F U N C T I O N S - V C R
INDEX SEARCH
NOTES:
VCR FUNCTIONS - BASIC
Most JVC-brand VCR’s automatically
The following buttons control the basic
Index marks are a
function of JVC-
made video
decks. Therefore,
INDEX SEARCH
insert an index mark at the start of a
recording. The INDEX SEARCH +/- buttons
can be used to scan a cassette for
these marks, to quickly find the
functions of the VCR.
PLAY
beginning of a taped program.
cannot be used
on commercially
produced tapes,
or tapes recorded
on non-JVC brand
VCR’s, since these
tapes will not have
the JVC index
❑ Begins playback of a video cassette.
INDEX SEARCH +
REW
Scans tape forward for index marks. If
there are numerous programs recorded
on one tape, you can press the INDEX
SEARCH button a number of times to
search for that number of marks. (For
example four presses will move ahead
four index marks). A recording up to nine
index marks ahead may be accessed.
❑ Rewinds tape. If pressed when tape is
stopped, the tape counter will be
displayed on screen. Can also be used
with PLAY to scan backwards through
tape.
marks recorded
on them.
If you try to begin
an index search at
a point on the
FF
INDEX SEARCH -
❑ Fast Forward. If pressed when tape is
stopped, the tape counter will be
displayed on screen. Can also be used
with PLAY to scan forward through tape
at an accelerated rate.
tape between two
programs, INDEX
SEARCH may not
work correctly.
Either fast-forward,
or rewind the tape
a bit and try INDEX
SEARCH again.
Scans tape backward for index marks. If
there are numerous programs recorded
on one tape, you can press the INDEX
SEARCH button a number of times to
search for that number of marks. (For
example four presses will move back four
index marks). A recording up to nine
index marks behind may be accessed.
PAUSE
❑ Freezes a single frame of video on
screen during playback. Press PLAY to
resume normal playback.
❑ While tape is paused, you can
advance forward frame-by-frame. Each
press of the PAUSE button will move the
tape ahead one frame.
❑ While tape is playing back, you can
slow the speed to 1/6 of normal by
pressing and holding PAUSE for two
seconds.
TRACKING ADJUSTMENT
During playback, if tracking (the
alignment of the video heads on the
video cassette tape) deviates, an unclear
picture is displayed. This TV/VCR Combo
is equipped with an automatic tracking
function. There are are cases when
manual tracking adjustment is needed.
They include:
• When the auto tracking does not work
properly and the picture remains unclear.
• If the picture moves vertically during
playback
REC
❑ Immediately begins recording of
program currently on television. To start
recording, press PLAY while holding
down REC button.
Open the cover of the TV/VCR
combo front panel.
Press the CHANNEL + and
CHANNEL - on the front panel
simultaneously during playback.
Note: No special tracking indication will
appear on screen.
STOP
❑ Halts VCR function. Will stop tape
during play, record, fast-forward, or
rewind functions. If pressed while REW
or FF is being used with PLAY, tape will
return to normal playback.
Press either the CHANNEL + or
CHANNEL - buttons to reduce the
disturbance or vertical vibration
of the picture.
Note: Once video cassette is removed,
manual tracking will automatically be
turned off.
Download from Www.Somanuals.com. All Manuals Search And Download.
27 B U T T O N F U N C T I O N S - V C R
SHUTTLE PLUS +/-
SKIP SEARCH
Lets you gradually increase or decrease the
playback speed of a video cassette. With a
videotape playing choose either the SHUTTLE
PLUS + or SHUTTLE PLUS - button.
Each time you press the SKIP SEARCH button
while a tape is playing, the unit will fast-
forward ahead 30 seconds on the tape. You
may press the button up to four times in a
row to move 120 seconds or two minutes
ahead.
SHUTTLEPLUS +
SKIP SEARCH
Each time this button is pushed, playback
speed will increase. Button can be pushed
a maximum of seven times.
RE-VIEW
Once a timer-recording has finished,
pressing the RE-VIEW button automatically
rewinds the tape to the start of the newly
recorded program.
SHUTTLE PLUS -
Each time this button is pushed, playback
speed will decrease. Button can be pushed
a maximum of seven times.
RE-VIEW
Note: No other VCR functions can be used
before pressing RE-VIEW. Using any other
functions will prevent RE-VIEW from working.
To resume playback at normal speed, press
the PLAY button.
EZJECT
TIMER
The video cassette is automatically
rewound and then ejected with one push of
the EZJECT button.
Lets you turn the TimerModeON and OFF.
TIMER
EZJECT
VCR PLUS+
+
Accesses the TV/VCR Combo's VCR Plus
DISPLAY
functions. For more information on timer
recording with VCR Plus , see page 22.
By pressing DISPLAY while a video cassette
is playing you can check on how much
tape remains or tape speed. Display also
shows the tape counter on-screen. Refer to
page 24 for more details.
+
VCRPLUS+
DAILY/WEEKLY
DISPLAY
Selects how often a program will be record-
ed: Once, Daily, or Weekly. Pressing
Daily/Weekly will access this option in the
Timer Recording menu.
CANCEL
Use to cancel a pre-set timed program or if
+
you input a VCR Plus code incorrectly on
the VCR Plus screen.
DAILY/WEEKLY
+
CANCEL
SP/EP
Selects a recording speed (SP or EP) for
simple recording. See "Regular VCR
Programming"on page 20 for more details.
SP/EP
Download from Www.Somanuals.com. All Manuals Search And Download.
28
B U T T O N F U N C T I O N S - V C R
Program Check Continued
PROGRAM CHECK
The PROGRAM CHECK button allows you
to confirm the programmed settings of
your VCR. You can also make changes
if you find any errors.
Use the Menu buttons to select which
items you wish to change. (For more on
Regular VCR Programming, see page
20).
Confirm Timer Settings.
Cancelling Timer Programs
Press the Program Check button to
display the timer information
Press the Program Check button to
display the timer information
PROG. CHECK
PROG. CHECK
Select the program you wish to cancel
CANCEL
❑ Press again to leave screen.
Changing Timer Settings
If you find an error, you may correct it
from the program check screen.
Press PROG. CHECK again to exit.
To program you wish to change
REC/ITR
(On TV/VCR Combo unit front panel)
REC/ITR
Pressing the REC/ITR button once will begin
videotape recording on on-screen program.
Pressing button a second time will activate
ITR (Instant Timer Recording)timer. See
“Instant Timer Recording” on page 23 for
more information.
To display “REGULAR VCR
PROGRAMMING”screen.
STOP/EJECT
(On TV/VCR Combo unit front panel)
STOP/EJECT
Pressing the STOP/EJECT button once will
halt any on-going VCR function such as
playback, record, rewind, etc. Press the
button while the VCR is stopped to eject
video cassettes.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
2 T R O U B L E S H O O T I N G - T V
PROBLEMS
CHECK
There is no power
• See if the power cord became unplugged.
• Perhaps you have experienced a blown circuit breaker or fuse or a power outage.
• The antenna could be disconnected.
There is no picture
or no sound
• The input mode (TV or Video) could not be set properly, refer to page 25.
• The tuner mode (in the Auto Tuner Setup) could be set improperly, refer to page 12.
• The station may be having difficulties, check to see if other channels are operating normally.
Remote control is
not operating or
• Check that the batteries are still working and properly installed.
• Make sure there are no objects blocking a clear path from the remote to the TV.
operating properly • Check that the TV/CATVswitch is in the proper position — set to TV to view television.
• Maybe you are too far from the TV, you must be within 23 feet (or 7 meters).
• Make sure the channels are programmed. See Channel Summary, page 12.
• Perhaps the channel is locked, select it with the 10 key pad and follow instructions on page 13.
You cannot select a
certain channel
• Perhaps the On/Off Timer is set, press the power button, check page 18.
• The power was interrupted or the power cord unplugged. Reset the clock, check page 17.
• The Sleep Timer may be set, check page 24
The power turns off
by itself
The clock is wrong • The power was interrupted and the clock not reset. Reset the clock, check page 17.
• There is a problem with the TV. Unplug the set and call for service.
On Timer is blinking
PICTURE
CHECK
The picture color
quality is poor
• Tint and color may be improperly adjusted. Check page 15.
• Video Status mode may be set to an inappropriate setting. Check page 24.
• There could be interference from another energy consuming appliance, such as a computer,
another TV or VCR. Move any other such appliances farther away from the TV.
There are lines
across the picture
The picture is
spotted
• There could be interference from a running high wattage appliance such as a hair-dryer, vacuum
cleaner, or neon sign. You will have to move the antenna away from the source of the
interference or change it to a coaxial cable which is less prone to interference.
• A building or airplane can reflect the original signal producing a second, delayed one. Adjust
the antenna position.
Double picture
(Ghosts)
Snowy picture/
Image noise
• The antenna may be damaged, disconnected or turned. Check the antenna connection,
page 6, and your Quick Setup Guide. If it is damaged, you will have to replace it.
Screen is 80% black • Closed Caption Text Mode is on. Turn it off in the Closed Caption Menu (page 18).
CHECK
SOUND
Bilingual or stereo
• Make sure the MTS mode is properly set. Refer to page 16 for details on setting MTS Modes.
programscan’tbeheard
• The volume is set to “0”. Adjust it by pressing the VOLUME + button.
There is no sound
from the TV
• Has the Muting button been pressed? If so, press Muting again to return volume to normal.
• Is an earphone/headphone attached to the jack at the front of the TV? If the phones jack is in
use, the TV’s speakers will not produce sound.
speakers.
DON’T WORRY ABOUT THIS, IT’S NORMAL
NOT A PROBLEM
• It is normal to feel a surge of static electricity if you brush over or touch the screen.
Static electricity
• It is normal for the TV to emit crackling sounds when turned on or off. Unless the sound or
picture become abnormal, this is fine.
You hear occasional
crackling sounds
Download from Www.Somanuals.com. All Manuals Search And Download.
30
T R O U B L E S H O O T I N G - V C R
CHECK
The video cassette • Make sure you are attempting to insert the tape properly. The clear window on the cassette
PROBLEMS
will not enter the
VCR
should be facing up and the label on the narrow part of the cassette should face away
from the machine.
• Are you attempting to use a cassette that is not a VHS or S-VHS type? Only these types of
cassettes may be used in this machine.
• Is the VCR set for timer-recording? A cassette cannot be removed while the timer is running.
To eject the tape while the timer is operating, press the TIMER button on the remote control to
shut it off. You may then press EJECT on the front panel of the unit to remove the tape.
The cassette will not
eject
• This VCR allows for recording and playback in mono sound only.
Dual or stereo
sound cannot be
heard
• When a tape with stereo Hi-Fi recorded as its normal track is played back, two separate
soundtracks may be heard at the same time. Make sure when renting or purchasing recorded
video tapes that they are compatible with monaural sound mode.
Two sounds are
heard at the same
time during
playback
Unit makes
mechanical-type
sounds when no
operation is being
performed
• Is the VCR set to begin timer-recording? When a timer-recording starts, it is normal to hear the
cassette tape being engaged inside the machine. This is not a malfunction.
• Have you just finished watching a tape? Two or three minutes after you finish watching a tape,
the VCR heads automatically disengage from the tape to protect the tape. Sound is also heard
at this time. This is not a malfunction either.
The cassette gets
stuck halfway
during loading or
unloading
• Try unplugging the unit from the power outlet, then plugging back in. If this does not work, call
your local dealer for service.
• During recording, playback, or fast-forwarding when the unit reaches the end of the tape, it
starts rewinding automatically.
• Is the VCR set to Repeat Play? See "Repeat Play", page 21.
The VCR started
rewinding the tape
automatically
Recording won’t
start
• Has the safety tab at the rear of the cassette been removed? A cassette cannot be used for
recording without this tab. If the tab is missing and you still want to record on that tape, cover
the hole with two layers of adhesive tape.
“Noise” (static)
appears on the
picture during
playback
• The VCR heads may be dirty. Use a commercially available cleaning cassette to clean the
heads.
Still (paused)
picture vibrates up
and down
• Manually adjust the VCR’s tracking. See "Tracking Adjustment", page 26.
VCR cannot be set
for timer-recording
• Are you trying to timer-record more than six programs? The maximum number of timer-
recordings that can be set at one time is six.
• Do timer-recordings overlap? You can check timer settings by pressing PROG. CHECK on the
remote control. For PROG. CHECK, see page 28. For timer recording overlap, see page 20.
•Is there a video cassette inserted in the unit? If there is no cassette inserted, the VCR cannot
be operated.
The VCR cannot be
operated
Timer-recording is
set but VCR cannot
timer record.
• Do timer-recording overlap? See the "Notes on overlapping programs" on page 20.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
3 L I M I T E D W A R R A N T Y
For Canadian model televisions, see separate sheets for Warranty/Garantie and
JVC Authorized Service Centers in Canada.
JVC COMPANYOF AMERICAwarrants this product and all parts thereof, except as set forth below ONLYTO THE ORIGINALPURCHASER ATRETAIL
to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIPfrom the date of original retail purchase for the period shown below (the “Warranty
Period”) (PICTURE TUBE is covered for Two (2) years.)
Parts
Labor
1 YEAR
90 DAYS
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES,THE DISTRICT OF COLUMBIA AND COMMONWEALTH OF
PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective within the warranty period, JVC will repair or replace defective parts at no charge to the
original owner. Such repair and replacement services shall be rendered by JVC during regular business hours at JVC authorized
service centers. Parts used for replacement are warranted only for the remainder of this Warranty Period. All products and parts
thereof may be brought to a JVC authorized service center on a carry-in basis. Televisions with a screen size of 25 inches and larger may be
covered on an in-home basis where such service is available.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
To determine if in-home service is available in your area, either contact the selling dealer (retailer) or call 1-800-537-5722 to locate the nearest JVC
authorized service center. Service locations can also be obtained from our website http://www.jvcservice.com. In-home service, if available, will require
clear access to the Television by the service representatives. If in-home service is not available, carry in service will be provided.
If service is not locally available, box the product carefully, preferably in its original carton,and ship, insured,with a copy of your bill of sale
plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location which will be given to you by the
toll free number.
If you have any questions concerning your JVCProduct,please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1) Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty
installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to
render such service, or if affixed to any attachment not provided with the products, or if the model or serial number has been altered,
tampered with,defaced or removed;
2) Initial installation, installation and removal from "built-in" entertainment centers and other mounting systems;
3) Operational adjustments covered in the Owner’s Manual,normal maintenance, video and audio head cleaning;
4) Damage that occurs in shipment,due to an act of God,and cosmetic damage;
5) Signal reception problems and failures due to line power surge;
6) Video Pick-upTubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;
7) Accessories;
8) Batteries (except that Rechargeable Batteries are covered for 90 days from date of purchase.)
There are no express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES,INCLUDING THE IMPLIED WARRANTYOFMERCHANTABILTY, IS LIMITEDTOTHEDURATION
OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE,OR ANY OTHER DAMAGES,WHETHER DIRECT,
INCIDENTAL OR CONSEQUENTIAL (INCLUDING,WITHOUT LIMITATION, DAMAGE TO TAPES, RECORDS OR DISCS) RESULTING FROM THE
USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET
FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long the warranty lasts, so these
exclusions or limitations may not apply to you.This warranty gives you specific legal rights and you may also have other rights which vary
state to state.
JVCCOMPANY OF AMERICA
1700 Valley Road
DIVISION OF JVC AMERICAS CORP.
Wayne, New Jersey 07470
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY.THIS WARRANTY DOES NOT APPLY FOR DETAILS OF
REFURBISHED PRODUCT WARRANTY. PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION
PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No.and Serial No. which is located either on the rear, bottom or side of the cabinet.
Retain this information for future reference.
Model No.:
Serial No.:
Purchase Date:
Name Of Dealer:
Download from Www.Somanuals.com. All Manuals Search And Download.
32
A U T H O R I Z E D S E R V I C E C E N T E R S
QUALITY
SERVICE
HOW TO LOCATEYOUR JVC SERVICE CENTER
TOLL FREE: 1 (800) 537-5722
Dear Customer;
In order to receive the most satisfaction from your purchase, read the instruction booklet before operating the unit. In the
event that repair is necessary, or for the address nearest your location, please refer to the factory service center list below
or within the Continental United States, call 1-800-537-5722 for your authorized servicer. Remember to retain your Bill of
Sale for Warranty Service.
— JVC
JVC SERVICE & ENGINEERING
COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
FACTORY SERVICE CENTER LOCATIONS
Dear customer;
In order to receive the most satisfaction from your purchase, read this guide before operating the unit, and before calling
for service make sure you check the Troubleshooting pages at the end of this book. In the event that repair is necessary, or
for the address nearest you, please refer to the factory service center list below, or within the continental United States, call
the toll free number above for an authorized service center. Remember to retain your bill of sale for warranty service.
107 Little Falls Road
Fairfield, NJ 07004-2105
(973) 808-9279
1500 Lakes Parkway
Lawrenceville, GA 30243-5857
(404) 339-2522
705 Enterprise Street
Aurora, IL 60504-8149
(630) 851-7855
5665 Corporate Avenue
Cypress, CA 90630-0024
(714) 229-8011
2969 Mapunapuna Place
Honolulu, HA 96819-2040
(808) 833-5828
10700 Hammerly Suite 110
Houston, TX 77043
(713) 935-9331
13 Cummings Park
Woburn, MA 01801
(781) 376-9100
8192 State Road 84
Davie, FL 33324
(954) 472-1960
890 Dubuque Avenue
South San Francisco, CA 94080-1804
(650) 871-2666
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and
production of the wide array of JVC products, service is key to maintaining the high level of performance for which JVC
is world famous. The JVC service and engineering organization stands behind our products.
NATIONAL HEADQUARTERS
JVC SERVICE & ENGINEERING COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
1700 Valley Road
Wayne, New Jersey 07470
IF YOU SHIP THE PRODUCT
Don’t service it yourself.
CAUTION
Pack your JVC unit in the original carton or one of equivalent
size and strength. Enclose, with the unit, a letter stating the
problem or symptom that exists and also a copy of the receipt or
bill of sale you received when you purchased your JVC unit. Print
your home return address on the outside and inside of the
carton, Send to the appropriate JVC Factory Service Center as
listed above.
To prevent electrical shock, do not open the
cabinet. No user serviceable parts inside.
Refer to qualified service personnel.
ACCESSORIES
To purchase accessories for your JVC product, you may contact your local JVC Dealer. Or from the
48 Continental United States call toll free : 1 (800) 882-2345
Download from Www.Somanuals.com. All Manuals Search And Download.
33 M E M O
Download from Www.Somanuals.com. All Manuals Search And Download.
34
M E M O
Download from Www.Somanuals.com. All Manuals Search And Download.
S P E C I F I C A T I O N S
MODEL
Type
TV-20240
TV/VCR Combo
Reception Format
NTSC, BTSC System (Multi Channel Sound)
VHF 2 to 13. UHF 14 to 69 Sub Mid, Super, Hyper, and Ultra bands
(181 channel frequency synthesizer system)
Reception Range
Power Supply
120VAC, 60 Hz
100W / 1.5A
Power consumption
20 Inches / 50.8 cm measured diagonally full square
1.2W x 1.2W
Screen Size
Audio Output
Speakers
1-4/5" x 4" / 4.5 x 10 cm oval x 2
Antenna Terminal
75 ohms (VHF/UHF) terminal (F-type connector)
Video: 1 Vp-p., 75 ohms
Audio: 500mVrms (-4dBs audio) high impedance
External input jacks
Phones jack
3.5 mm stereo mini-jack
Recording/Playback
system
VHS system (SQPB)
4 head helical scan system
Video Signal
Recording system
Tape Speed
NTSCsystem
VHS monaural system Monaural-linear track system
EP / SP
1- month programmable timer / 6 programs
Program capacity
Memory backup
time
Approximately 90 seconds
Clock Reference
AC
External Dimensions
(W x H x D)
22 5/8" x 19 7/8"x 19 1/8" / 57.2 x 50.3 x 48.3 (cm)
52.4 (lbs.) / 23.8 (kg.)
Weight (lbs./kg.)
Accessories
1 Remote control unit, 2 AA batteries
Specifications subject to change without notice.
LCT0316-001A-H
0299-TN-JII-JMT
Download from Www.Somanuals.com. All Manuals Search And Download.
|