JVC Stereo System CA MXJ50 User Manual

COMPACT COMPONENT SYSTEM  
CA-MXJ750R/CA-MXJ552R  
CA-MXJ550R/CA-MXJ500  
COMPACT  
COMPACT  
COMPACT  
COMPACT  
SOUND  
MODE  
SOUND  
MODE  
SOUND  
MODE  
SLEEP  
SLEEP  
SLEEP  
SOUND  
MODE  
SLEEP  
DIGITAL AUDIO  
DIGITAL AUDIO  
DIGITAL AUDIO  
DISPLA  
Y
DISPLAY  
DISPLAY  
MODE  
PTY/EON  
SELECT  
+
MODE  
MODE PTY/EON  
SELECT  
+
PTY/EON  
SELECT  
+
DIGITAL AUDIO  
TAPE A/B  
TAPE A/B  
TAPE A/B  
TAPE A/B  
REC  
START/STOP  
REC  
START/STOP  
REC  
START/STOP  
REC  
START/STOP  
ACTIVE  
BASS EX.  
ACTIVE  
BASS EX.  
ACTIVE  
BASS EX.  
FM MODE  
FM MODE  
FM MODE  
FM MODE  
+
+
+
+
FADE  
MUTING  
FADE  
MUTING  
FADE  
MUTING  
FADE  
MUTING  
RM–SMXJ550R REMOTE CONTROL  
RM–SMXJ750R REMOTE CONTROL  
RM–SMXJ550R REMOTE CONTROL  
RM–SMXJ500E REMOTE CONTROL  
CA-MXJ750R  
CA-MXJ552R  
CA-MXJ550R  
CA-MXJ500  
INSTRUCTIONS  
For Customer Use:  
Enter below the Model No. and Serial  
No. which are located either on the rear,  
bottom or side of the cabinet. Retain this  
information for future reference.  
Model No.  
Serial No.  
GVT0029-008A  
[ B ]  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”  
This equipment has been disigned and manufactured to meet international safety standards but, like any electrical equipment, care  
must be taken if you are to obtain the best results and safety is to be assured.  
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮  
Do read the operating instructions before you attempt to use the equipment.  
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment)  
are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or  
changing connections.  
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.  
Do be careful with glass panels or doors on equipment.  
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮  
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way–switch off,  
withdraw the mains plug and consult your dealer.  
DON’T remove any fixed cover as this may expose dangerous voltages.  
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation  
or has a standby mode.  
Switch off using the switch on the equipment and make sure that your family know how to do this.  
Special arrangements may need to be made for infirm or handicapped people.  
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is  
illegal to watch television whilst driving.  
DON’T listen to headphones at high volume as such use can permanently damage your hearing.  
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.  
Overheating will cause damage and shorten the life of the equipment.  
DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit the manufacturer’s  
approved stand or legs with the fixings provided according to the instructions.  
DON’T allow electrical equipment to be exposed to rain or moisture.  
ABOVE ALL  
— NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case -this could result  
in a fatal electrical shock.;  
— NEVER guess or take chances with electrical equipment of any kind  
— it is better to be safe than sorry!  
– G-2 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
We would like to thank you for purchasing one of our JVC products.  
Before operating this unit, read this manual carefully and thoroughly to  
obtain the best possible performance from your unit, and retain this manual  
for future reference.  
Power sources  
• When unplugging from the wall outlet, always pull the  
plug, not the AC power cord.  
About This Manual  
This manual is organized as follows:  
The manual mainly explains operations using the  
buttons and controls on the unit. You can also use the  
buttons on the remote control if they have the same or  
similar names (or marks) as those on the unit.  
If operation using the remote control is different from  
that using the unit, it is then explained.  
• Basic and common information that is the same for many  
functions is grouped in one place, and is not repeated in  
each procedure. For instance, we do not repeat the  
information about turning on/off the unit, setting the  
volume, changing the sound effects, and others, which are  
explained in the section “Common Operations” on pages 9  
to 11.  
DO NOT handle the AC power cord with wet  
hands.  
Moisture condensation  
Moisture may condense on the lens inside the unit in the  
following cases:  
• After starting heating in the room  
• In a damp room  
• If the unit is brought directly from a cold to a warm place  
Should this occur, the unit may malfunction. In this case,  
leave the unit turned on for a few hours until the moisture  
evaporates, unplug the AC power cord, and then plug it in  
again.  
• The following marks are used in this manual:  
Gives you warnings and cautions to prevent  
damage or risk of fire/electric shock.  
Also gives you information which is not good  
for obtaining the best possible performance  
from the unit.  
Others  
• Should any metallic object or liquid fall into the unit,  
unplug the unit and consult your dealer before operating  
any further.  
• If you are not going to operate the unit for an extended  
period of time, unplug the AC power cord from the wall  
outlet.  
Gives you information and hints you had better  
know.  
DO NOT disassemble the unit since there are no  
user serviceable parts inside.  
Precautions  
If anything goes wrong, unplug the AC power cord and  
consult your dealer.  
Installation  
• Install in a place which is level, dry and neither too hot nor  
too cold — between 5˚C (41˚F) and 35˚C (95˚F).  
• Install the unit in a location with adequate ventilation to  
prevent internal heat built-up in the unit.  
• Leave sufficient distance between the unit and the TV.  
• Keep the speakers away from the TV to avoid interference  
with TV.  
DO NOT install the unit in a location near heat  
sources, or in a place subject to direct sunlight,  
excessive dust or vibration.  
– 1 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Location of the Buttons and Controls ....................... 3 Playing Back Tapes ................................................... 18  
Front Panel ................................................................. 3  
Remote Control .......................................................... 5  
Playing Back a Tape ................................................. 18  
Locating the Beginning of a Song — Music Scan ... 18  
Getting Started............................................................ 6 Recording .................................................................. 19  
Unpacking .................................................................. 6  
Putting the Batteries into the Remote Control ........... 6  
Connecting Antennas ................................................. 6  
Connecting Speakers .................................................. 7  
Connecting Other Equipment..................................... 8  
Recording a Tape on Deck B.................................... 19  
Dubbing Tapes.......................................................... 20  
CD Direct Recording ................................................. 20  
Auto Edit Recording.................................................. 21  
Using the Timers ....................................................... 22  
Common Operations .................................................. 9  
Using Daily Timer .................................................... 22  
Using Recording Timer ............................................ 23  
Using Sleep Timer .................................................... 24  
Timer Priority ........................................................... 24  
Turning On or Off the Power ....................................... 9  
Setting the Clock ........................................................ 9  
Selecting the Sources................................................... 9  
Adjusting the Volume ............................................... 10  
Reinforcing the Bass Sound ..................................... 10  
Selecting the Sound Modes ...................................... 10  
Creating Your Own Sound Mode  
Maintenance .............................................................. 25  
Troubleshooting ........................................................ 26  
Additional Information ............................................ 27  
Specifications............................................................. 28  
— Manual Mode................................................. 11  
Listening to FM and AM (LW/MW) Broadcasts ... 12  
Tuning in a Station ................................................... 12  
Presetting Stations .................................................... 12  
Tuning in a Preset Station ........................................ 12  
Receiving FM Stations with RDS ............................ 13  
Changing the RDS Information ............................... 13  
Searching for Programs by PTY Codes  
(PTY Search) ...................................................... 13  
Switching to a Program Type of Your  
Choice Temporarily ............................................ 14  
Playing Back CDs ..................................................... 15  
Loading CDs ............................................................ 15  
Playing Back the Entire Discs  
— Continuous Play............................................. 15  
Basic CD Operations ................................................ 15  
Programming the Playing Order of the Tracks  
— Program Play ................................................. 16  
Playing at Random — Random Play ....................... 17  
Repeating Tracks or CDs — Repeat Play ................ 17  
Prohibiting Disc Ejection — Tray Lock................... 17  
– 2 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Location of the Buttons and Controls  
Become familiar with the buttons and controls on your unit.  
Front Panel  
j
k
l
Powered Rolling Panel  
o
;
a
s
/
z
d
f
x
c
Press PANEL OPEN/  
CLOSE to open the panel.  
To close the panel, press  
the button again.  
g
h
v
b
n
Front Panel  
1
p
2
3
q
4
CA-MXJ750R  
w
e
r
5
6
CA-MXJ552R  
CA-MXJ550R  
CA-MXJ500  
7
t
y
8
9
u
i
– 3 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Continued  
Display Window  
1
2
3
4
5
6
1
2
3
p
q
7 8 9  
See pages in the parentheses for details.  
h SET button (9, 12, 22 – 24)  
j 7 (stop) button (15 – 21)  
k TUNING – / + buttons (12)  
1 / ¡ (fast left/fast right) buttons (11, 16, 18)  
l SEA CONTROL button (11)  
/ PROGRAM/RANDOM button (16, 17, 20)  
z EDIT button (21)  
Front Panel  
1 Disc trays  
2
(On/Standby) button and STANDBY lamp (9)  
3 Display window  
4 For CA-MXJ750R:  
x REPEAT button (17)  
c DISPLAY button (9)  
SUBWOOFER VOLUME control (10)  
For CA-MXJ552R/CA-MXJ550R/CA-MXJ500:  
ACTIVE BASS EX. (extension) LEVEL control (10)  
5 Remote sensor  
6 TAPE 2 3 button and lamp (9, 18)  
Pressing this button also turns on the unit.  
7 AUX button and lamp (9)  
v SOUND MODE button (10)  
b CANCEL button (9, 17, 22)  
DEMO button (8)  
n For CA-MXJ750R/CA-MXJ552R/CA-MXJ550R ONLY:  
RDS operation buttons (13)  
• DISPLAY MODE, PTY/EON, and SELECT – / +  
buttons  
Pressing this button also turns on the unit.  
8 Deck A cassette holder (18)  
9 0 EJECT button for deck A (18)  
p Disc number buttons (CD1, CD2, and CD3) (15)  
Pressing one of these buttons also turns on the unit.  
q 0 (CD tray open/close) buttons (15)  
Pressing one of these buttons also turns on the unit.  
w VOLUME control (10)  
Display window  
1 For CA-MXJ750R/CA-MXJ552R/CA-MXJ550R ONLY:  
RDS operation indicators  
• RDS, EON, and TA/NEWS/INFO indicators  
2 Timer indicators  
e CD £¥8 (play/pause) button and lamp (9, 15)  
Pressing this button also turns on the unit.  
r PANEL OPEN/CLOSE button (9)  
Pressing this button also turns on the unit.  
t PHONES jack (10)  
• DAILY (Daily Timer), REC (Recording Timer), SLEEP,  
and  
(Timer) indicators  
3 CD play mode indicators  
• REPEAT (ALL/1CD/1), PROGRAM, and RANDOM  
indicators  
y FM/AM button and lamp (9, 12)  
Pressing this button also turns on the unit.  
u Deck B cassette holder (18, 19)  
i EJECT 0 button for deck B (18, 19)  
4 CD track number indicators  
5 Disc indicators  
6 SEA (Sound Effect Amplifier) pattern indicator  
7 For CA-MXJ750R: SUBWOOFER indicator (10)  
For CA-MXJ552R/CA-MXJ550R/CA-MXJ500:  
BASS indicator (10)  
8 Tuner operation indicators  
• MONO and STEREO indicators  
9 Tape operation indicators  
Powered Rolling Panel  
o PRESET – / + buttons (12)  
4 / ¢ (reverse search/forward search) buttons  
(9, 11, 16, 21 – 24)  
(reverse mode), A/B (operating deck), 2 3 (tape  
; REVERSE MODE button (18 – 21)  
a REC START/STOP button (19, 21)  
s DUBBING button (20)  
d CD REC START button (20, 21)  
f TAPE A/B button (18)  
direction), and REC (recording) indicators  
p SOUND MODE indicator  
q Main display  
• Shows the source name, frequency, etc.  
g CLOCK/TIMER button (9, 22 – 24)  
– 4 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control  
Remote Control  
1 Disc number buttons (CD1, CD2, and CD3) (15)  
Pressing one of these buttons also turns on the unit.  
2 SOUND MODE button (10)  
3 TAPE A/B button (18)  
4 REC START/STOP button (19, 21)  
5 For CA-MXJ750R: SUBWOOFER + / – buttons (10)  
For CA-MXJ552R/CA-MXJ550R/CA-MXJ500:  
ACTIVE BASS EX. (extension) + / – buttons (10)  
6 1 / 4 (fast left/reverse search) button (16 – 18)  
7 TAPE 2 3 button (9, 18)  
1
2
p
SOUND  
MODE  
SLEEP  
q
w
DISPLAY  
MODE  
PTY/EON  
SELECT  
+
5
CA-MXJ750R  
Pressing this button also turns on the unit.  
8 FADE MUTING button (10)  
TAPE A/B  
3
REC  
START/STOP  
9 AUX button (9)  
4
e
Pressing this button also turns on the unit.  
p
(On/Standby) button (9)  
q SLEEP button (24)  
w For CA-MXJ750R/CA-MXJ552R/CA-MXJ550R ONLY:  
RDS operation buttons (13)  
• DISPLAY MODE, PTY/EON, and SELECT – / +  
buttons  
e Number buttons (12, 16)  
FM MODE  
CA-MXJ552R  
CA-MXJ550R  
CA-MXJ500  
r
t
ACTIVE  
6
7
BASS EX.  
+
y
FADE  
MUTING  
u
i
r FM MODE button (12)  
8
9
t ¢ / ¡ (forward search/fast right) button (16 – 18)  
y CD £¥8 button (9, 15)  
o
Pressing this button also turns on the unit.  
u 7 (stop) button (15 – 21)  
i FM/AM button (9, 12)  
Pressing this button also turns on the unit.  
o VOLUME + / – buttons (10)  
When using the remote control, point it at  
the remote sensor on the front panel.  
– 5 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Getting Started  
Continued  
Unpacking  
Connecting Antennas  
After unpacking, check to be sure that you have all the  
following items.  
FM antenna  
The number in the parentheses indicates the quantity of the  
pieces supplied.  
A
N
N
TE  
N
A
FM antenna (supplied)  
• AM (LW/MW) loop antenna (1)  
• FM antenna (1)  
EXT  
LOOP  
• Remote control (1)  
• Batteries (2)  
5  
L
IA  
If any is missing, consult your dealer immediately.  
Putting the Batteries into the Remote Control  
1 Attach the FM antenna to the FM 75  
Insert the batteries — R6(SUM-3)/AA(15F) — into the  
remote control, by matching the polarity (+ and –) on the  
batteries with the + and – markings on the battery  
compartment.  
When the remote control can no longer operate the unit,  
replace both batteries at the same time.  
COAXIAL terminal.  
2 Extend the FM antenna.  
3 Fasten it up in the position which gives you  
the best reception, then fix it on the wall, etc.  
1
About the supplied FM antenna  
The FM antenna supplied with this unit can be used as temporary  
measure. If reception is poor, you can connect an outdoor FM  
antenna.  
R6(SUM-3)/AA(15F)  
2
To connect an outdoor FM antenna  
Before connecting it, disconnect the supplied FM antenna.  
3
Outdoor FM antenna  
(not supplied)  
• DO NOT use an old battery together with a new one.  
• DO NOT use different types of batteries together.  
• DO NOT expose batteries to heat or flame.  
• DO NOT leave the batteries in the battery  
ANTENNA  
T
X
E
L
P
O
O
compartment when you are not going to use the  
remote control for an extended period of time.  
Otherwise, it will be damaged from battery leakage.  
5  
L
IA  
A 75 antenna with coaxial type connector (DIN 45325)  
should be used.  
– 6 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AM (LW/MW) antenna  
Connecting Speakers  
FOR CA-MXJ750R  
3
1
2
2, 3  
1
Vinyl-covered wire  
(not supplied)  
ANTENNA  
Blue  
AM EXT  
AM LOOP  
Speaker  
cord  
Speaker  
cord  
(blue/black)  
(blue/black)  
FM 75  
COAXIAL  
Red  
Black  
AM (LW/MW) loop  
antenna (supplied)  
Black  
Speaker cord  
(red/black)  
1 Connect the AM (LW/MW) loop antenna to  
the AM LOOP terminals as illustrated.  
2 Turn the AM (LW/MW) loop antenna until  
you have the best reception.  
To right  
speaker  
To left  
speaker  
To connect an outdoor AM (LW/MW) antenna  
When reception is poor, connect a single vinyl-covered wire  
to the AM EXT terminal and extend it horizontally. (The AM  
(LW/MW) loop antenna must remain connected.)  
FOR CA-MXJ552R/CA-MXJ550R/CA-MXJ500  
Red  
Speaker  
cord  
Speaker  
cord  
(red/black)  
(red/black)  
For better reception of both FM and AM (LW/MW)  
• Make sure the antenna conductors do not touch any other  
terminals and connecting cords.  
• Keep the antennas away from metallic parts of the unit,  
connecting cords, and the AC power cord.  
Black  
To left  
speaker  
To right  
speaker  
– 7 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 Press and hold the clamp of the speaker  
To connect audio equipment with an optical digital  
input terminal  
terminal on the rear of the unit.  
You can record CD sound onto the connected digital  
equipment.  
2 Insert the end of the speaker cord into the  
terminal.  
Match the polarity (color) of the speaker terminals: ª to  
ª and · to ·.  
Protective  
plug  
3 Release the finger from the clamp.  
IMPORTANT: Use only speakers with the same speaker  
impedance as indicated by the speaker terminals on the  
rear of the unit.  
Before connecting  
the other equipment,  
remove the  
protective plug from  
the terminal.  
Connecting Other Equipment  
You can connect both analog and digital equipment.  
Audio equipment  
with an optical digital  
input  
• DO NOT connect any equipment while the power  
is on.  
• DO NOT plug in any equipment until all  
connections are complete.  
To optical  
digital input  
To connect an analog component  
Connect an optical digital cord (not supplied) between the  
optical digital input terminal on the other equipment and the  
CD OPTICAL DIGITAL OUTPUT terminal.  
Be sure that the plugs of the audio cords are color coded:  
White plugs and jacks are for left audio signals, and red ones  
for right audio signals.  
NOW, you can plug in the unit and other  
connected equipment FINALLY!  
When connecting the AC power cord into a wall outlet, the  
unit automatically starts display demonstration.  
Audio/video  
equipment  
To stop the display demonstration, press any button on the  
unit or on the remote control.  
To audio output  
For playing the other equipment through this unit,  
connect between the audio output jacks on the other  
equipment and AUX jacks by using audio cords (not  
supplied).  
To start the display demonstration manually  
Press and hold DEMO for more than 2  
seconds.  
To stop the demonstration, press any button.  
– 8 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Common Operations  
Turning On or Off the Power  
4 Press 4 or ¢ to adjust the  
minute, then press SET.  
To turn on the unit, press  
so that the  
STANDBY lamp goes off.  
The Powered Rolling Panel opens automatically.  
To check the clock time  
To turn off the unit (on standby), press  
again so that the STANDBY lamp lights up.  
Press DISPLAY while playing any source.  
• Each time you press the button, the source  
indication and the clock time alternate on the  
display.  
The Powered Rolling Panel also closes.  
A little power is always consumed even while the unit is on  
standby.  
To adjust the clock again  
If you have adjusted the clock before, you need to press  
CLOCK/TIMER repeatedly until the clock setting mode is  
selected.  
To switch off the power supply completely, unplug the AC  
power cord from the AC outlet.  
• Each time you press the button, the clock/timer setting  
modes change as follows:  
ON TIME  
REC  
DAILY  
When you unplug the AC power cord or if a power  
failure occurs  
The clock is reset to “0:00” right away, while the tuner preset  
stations (see page 12) will be erased in a few days.  
Clock  
Canceled  
ON TIME  
setting  
(The hour digits start flashing.)  
If there is a power failure  
The clock loses the setting and is reset to “0:00.” You need to set the  
clock again.  
Setting the Clock  
Before operating the unit any further, first set the clock built  
in this unit.  
Selecting the Sources  
On the unit ONLY:  
To listen to the FM/AM (LW/MW) broadcasts, press FM/  
AM. (See page 12.)  
To play back CDs, press CD £¥8. (See pages 15 – 17.)  
To play back tapes, press TAPE 2 3. (See page 18.)  
To select the external equipment as the source, press AUX.  
1 Press PANEL OPEN/CLOSE.  
The unit is turned on and the Powered Rolling  
Panel opens automatically.  
2 Press CLOCK/TIMER.  
The hour digits start flashing on the display.  
When you press the play button for a particular source (FM/  
AM, CD £¥8, AUX, and TAPE 2 3), the unit turns on, and  
the Powered Rolling Panel opens automatically (and the unit  
starts playing the source if it is ready — COMPU PLAY  
CONTROL).  
3 Press 4 or ¢ to adjust the  
hour, then press SET.  
• If you want to correct the hour after  
pressing SET, press CANCEL. The hour  
digits start flashing again.  
– 9 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Continued  
When using the remote control, press SUBWOOFER + to  
increase the subwoofer volume or press SUBWOOFER – to  
decrease it.  
Adjusting the Volume  
You can adjust the volume level only while the unit is turned  
on.  
For CA-MXJ552R/CA-MXJ550R/CA-MXJ500  
The ACTIVE BASS EX. (extension) LEVEL control  
provided for this unit can maintain the richness and fullness  
of the bass sound while listening to any source at low  
volume.  
Turn the VOLUME control clockwise to  
increase the volume or counterclockwise  
to decrease it.  
• The volume level can be adjusted in 32  
steps (MIN, VOL 1 — VOL 30, and  
MAX).  
Turn the ACTIVE BASS EX. LEVEL  
control clockwise to increase the bass  
sound or counterclockwise to decrease  
it.  
When using the remote control, press VOLUME + to increase • The bass sound level can be adjusted in  
the volume or press VOLUME – to decrease it.  
4 steps (BASS 1 — BASS 3, and  
MAX).  
For private listening  
Connect a pair of headphones to the PHONES jack. No sound  
comes out of the speakers. Be sure to turn down the volume before  
connecting or putting on headphones.  
BASS indicator always lights up when the  
unit is on.  
When using the remote control, press ACTIVE BASS EX. +  
to increase the bass sound level or press ACTIVE BASS EX. –  
to decrease it.  
DO NOT turn off (on standby) the unit with the  
volume set to an extremely high level; otherwise, a  
sudden blast of sound can damage your hearing,  
speakers and/or headphones when you turn on the  
unit or start playing any source next time.  
REMEMBER you cannot adjust the volume level  
while the unit is on standby.  
To cancel the Active Bass Extension, turn the control  
counterclockwise until “BASS OFF” appears.  
Selecting the Sound Modes  
To turn down the volume level temporarily  
Press FADE MUTING on the remote control.  
The volume level gradually decreases to “MIN.”  
To restore the sound, press the button again.  
You can select one of the 6 preset sound modes (3 surround  
modes and 3 SEA — Sound Effect Amplifier — modes). This  
function only affects the playback sound, but does not affect  
your recording.  
Reinforcing the Bass Sound  
To select the sound modes, press SOUND  
MODE until the sound mode you want appears on  
the display. The SOUND MODE indicator also  
lights up on the display.  
This function only affects the playback sound, but does not  
affect your recording.  
For CA-MXJ750R  
The SUBWOOFER VOLUME control provided for this unit  
can enhance the subwoofer sound if subwoofers are  
connected to the rear of this unit (see page 7).  
• Each time you press the button, the sound modes change as  
follows:  
Turn the SUBWOOFER VOLUME  
control clockwise to increase the  
subwoofer sound or counterclockwise  
to decrease it.  
• The subwoofer level can be adjusted in  
6 steps (WOOFER 1 — WOOFER 5,  
and MAX).  
D.CLUB HALL STADIUM ROCK  
(Dance CLUB)  
POP  
OFF  
(Canceled)  
CLASSIC  
MANUAL 3 MANUAL 2 MANUAL 1  
SUBWOOFER indicator always lights up  
when the unit is on.  
– 10 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Surround modes *:  
D.CLUB: Increases resonance and bass.  
2 Adjust the SEA pattern.  
HALL:  
Adds depth and brilliance to the sound.  
1) Press 4 or ¢ to select the  
frequency range to adjust  
(LOW, MID, HIGH).  
STADIUM: Adds clarity and spreads the sound, like in an  
outdoor stadium.  
SEA (Sound Effect Amplifier) modes:  
2) Press 1 or ¡ to adjust the  
level (–3 to +3) of the selected  
frequency range.  
ROCK:  
Boosts low and high frequency. Good for  
acoustic music.  
POP:  
Good for vocal music.  
CLASSIC: Good for classical music.  
3) Repeat steps 1) and 2) to adjust the level of  
the other frequency ranges.  
Manual modes:  
MANUAL 1/2/3:  
3 Press SEA CONTROL again.  
Your individual mode stored in memory. See  
“Creating Your Own Sound Mode — Manual  
Mode.”  
OFF:  
Cancels the sound mode.  
* Surround elements are added to the SEA elements to create a  
being-there feeling in your room.  
When one of these modes is selected, the SOUND MODE  
indicator lights up as —  
4 Press 4 or ¢ to select one of the  
MANUAL 1, 2, and 3 modes into which you  
want to store the SEA pattern.  
While one of the SEA modes including manual modes (SEA  
elements without surround elements) is selected,  
it lights up as —  
5 Press SEA CONTROL again.  
Creating Your Own Sound Mode — Manual  
Mode  
You can change SEA pattern to suit your preference. These  
changed settings can be stored in the MANUAL 1, 2, and 3  
modes.  
• There is a time limit in doing the following steps. If the  
setting is canceled before you finish, start from step 1  
again.  
If you want to add the surround elements in your SEA  
pattern, select one of the surround modes (D.CLUB,  
HALL, or STADIUM) before starting the procedure below.  
The SOUND MODE indicator also lights up.  
The SEA pattern you have created are stored into the  
MANUAL mode selected in the above step.  
To use your own sound mode  
Select MANUAL 1, 2, or 3 mode when using the sound  
modes. See “Selecting the Sound Modes.”  
On the unit ONLY:  
1 Press and hold SEA CONTROL  
until “SEA CONT” appears on the  
display.  
Current level appears.  
– 11 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening to FM and AM (LW/MW) Broadcasts  
Tuning in a Station  
2 Press SET.  
1 Press FM/AM.  
The unit automatically turns on and tunes in  
the previously tuned station (either FM or  
AM — LW/MW). The Powered Rolling  
Panel automatically opens.  
• Each time you press the button, the band alternates  
3 Press PRESET – / + to select a  
preset number.  
between FM and AM (LW/MW).  
2 Start searching for stations.  
On the unit:  
4 Press SET again.  
Press and hold TUNING – / + for  
more than 1 second.  
On the remote control:  
Press and hold 1 / 4 or  
¢ / ¡ for more than 1 second.  
The tuned station in step 1 is stored in the preset number  
selected in step 3.  
• Storing a new station on a used number erases the  
previously stored one.  
The unit starts searching for stations and  
stops when a station of sufficient signal  
strength is tuned in. If a program is broadcast in stereo,  
the STEREO indicator lights up.  
When you unplug the AC power cord or if a power  
failure occurs  
The preset stations will be erased in a few days. If this happens,  
preset the stations again.  
To stop during searching, press TUNING – / + (or  
1 / 4, ¢ / ¡).  
When you press TUNING – / + (or 1 / 4,  
¢ / ¡) briefly and repeatedly  
The frequency changes step by step.  
Tuning in a Preset Station  
1 Press FM/AM.  
To change the FM reception mode  
The unit automatically turns on and tunes in  
the previously tuned station (either FM or  
AM — LW/MW). The Powered Rolling  
Panel automatically opens.  
When an FM stereo broadcast is hard to receive or noisy,  
press FM MODE on the remote control so that the MONO  
indicator lights up on the display. Reception improves.  
To restore the stereo effect, press FM MODE  
again so that the MONO indicator goes off.  
In this stereo mode, you can hear stereo sounds  
when a program is broadcast in stereo.  
• Each time you press the button, the band  
alternates between FM and AM (LW/MW).  
2 Select a preset number.  
On the unit:  
Press PRESET – / +.  
On the remote control:  
Press the number buttons.  
For preset number 5, press 5.  
For preset number 15, press +10 then 5.  
For preset number 20, press +10, then 10.  
For preset number 25, press +10, +10,  
then 5.  
Presetting Stations  
You can preset 30 FM and 15 AM (LW/MW) stations.  
In some cases, test frequencies have been already memorized  
for the tuner since the factory examined the tuner preset  
function before shipment. This is not a malfunction. You can  
preset the stations you want into memory by following the  
presetting method.  
For preset number 30, press +10, +10,  
then 10.  
• There is a time limit in doing the following steps. If the  
setting is canceled before you finish, start from step 1  
again.  
On the unit ONLY:  
1 Tune in the station you want to preset.  
• See “Tuning in a Station.”  
MHz  
– 12 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Receiving FM Stations with RDS  
Searching for Programs by PTY Codes (PTY  
Search)  
This section is for the model having RDS functions —  
that is CA-MXJ750R, CA-MXJ552R, and CA-  
MXJ550R.  
One of the advantages of RDS is that you can locate a  
particular kind of program by specifying the PTY codes.  
• For details on the PTY codes, see “Additional Information”  
on page 27.  
RDS allows FM stations to send an additional signal along  
with their regular program signals. For example, the stations  
send their station names, as well as information about what  
type of program they broadcast, such as sports or music, etc.  
To search for a program using the PTY codes  
REMEMBER you must preset FM RDS stations to use the  
EON function. If not yet done, see page 12.  
• There is a time limit in doing the following steps. If the  
setting is canceled before you finish, start from step 1  
again.  
When tuned to an FM station which provides the RDS  
service, the RDS indicator lights up on the display.  
With the unit, you can receive the following types of RDS  
signals.  
1 Press PTY/EON until “PTY” and  
“SELECT” alternately appears on the  
display.  
PS (Program Service):  
Shows commonly known station names.  
PTY (Program Type):  
• Each time you press the button, RDS operation mode  
changes as follows:  
Shows types of broadcast programs.  
RT (Radio Text):  
PTY SELECT  
EON SELECT  
Shows text messages the station sends.  
Canceled  
EON (Enhanced Other Networks):  
Provides the information about the types of the  
programs sent by other RDS stations.  
2 Press SELECT – / + until the PTY  
code you want appears on the  
display.  
More about RDS  
• Some FM stations and AM (LW/MW) stations do not provide  
RDS signals.  
• RDS services vary among FM RDS stations. For details on RDS  
services in your area, check with local radio stations.  
• RDS may not work correctly if the received station is not  
transmitting the signals properly or if the signal strength is weak.  
• Each time you press the button, the PTY codes change  
as follows:  
NEWS AFFAIRS INFO SPORT “  
EDUCATE DRAMA CULTURE “  
SCIENCE VARIED POP M ROCK M “  
M.O.R. M LIGHT M CLASSICS “  
OTHER M WEATHER FINANCE “  
CHILDREN SOCIAL A RELIGION “  
PHONE IN TRAVEL LEISURE JAZZ “  
COUNTRY NATIONAL OLDIES “  
FOLK M DOCUMENT TRAFFIC “  
(back to the beginning)  
Changing the RDS Information  
You can see RDS information on the display while listening  
to an FM station.  
Press DISPLAY MODE.  
• Each time you press the button, the display  
changes to show the following information:  
PS  
PTY  
RT  
(Program Service) (Program Type)  
(Radio Text)  
Station frequency  
(or preset channel no.)  
3 Press PTY/EON once again.  
While searching, “SEARCH” and the selected  
PTY code alternate on the display.  
If no PS, PTY, or RT signals are sent by a station  
The unit searches 30 preset FM stations, stops  
when it finds the one you have selected (“FOUND”  
appears), and tunes in that station.  
• If no program is found, “NOT” and “FOUND”  
alternately appears on the display and the unit returns to  
the last received station.  
“NO PS,” “NO PTY,” or “NO RT” appears in the main display.  
If the unit takes time to show the RDS information  
received from a station  
WAIT PS”, “WAIT PTY”, or “WAIT RT” may appear on the  
display.  
To stop searching any time during the process  
Press PTY/EON while searching.  
– 13 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Switching to a Program Type of Your Choice  
Temporarily  
How the EON function actually works:  
CASE 1  
By receiving EON data sent by FM RDS stations, the EON  
function allows the unit to switch temporarily to a broadcast  
program of your choice (TA, NEWS, and INFO) from a  
different station.  
• The EON function only works when you are listening to a  
preset FM RDS stations providing EON data.  
• The EON indicator lights while receiving a station with  
EON data.  
If there is no station broadcasting the program you  
have selected  
The unit continues tuning in the current station.  
«
When a station starts broadcasting the program you have  
selected, the unit automatically switches to the station. The  
indicator of received PTY code starts flashing.  
«
When the program is over, “EON END” appears in the  
main display, and the unit goes back to the previously  
tuned station, but the EON function still remains activated.  
To activate the EON function  
REMEMBER you must preset FM RDS stations to use the  
EON function. If not yet done, see page 12.  
• There is a time limit in doing the following steps. If the  
setting is canceled before you finish, start from step 1  
again.  
CASE 2  
If there is a station broadcasting the program you have  
selected  
The unit tunes in the program. The indicator of received  
PTY code starts flashing.  
1 Press PTY/EON until “EON” and  
“SELECT” alternately appear on the  
display.  
«
• Each time you press the button, RDS operation  
mode changes as follows:  
When the program is over, “EON END” appears in the  
main display, and the unit goes back to the previously  
tuned station, but the EON function still remains activated.  
PTY SELECT  
EON SELECT  
Canceled  
CASE 3  
If the FM station you are listening to is broadcasting  
the program you have selected  
2 Press SELECT – / + until the  
EON data type you want appears  
on the display.  
The unit continues to receive the station but the indicator  
of received PTY code starts flashing.  
«
When the program is over, the indicator of received PTY  
code stops flashing and remains lit, but the EON function  
still remains activated.  
The selected EON data type indicator also  
flashes.  
More about the EON function  
• EON data sent from some stations may not be compatible with  
this unit. In this case, the EON function may not work correctly.  
• While listening to a program tuned in by the EON function, the  
station does not change even if another network station starts  
broadcasting a program of the same EON data.  
• The EON function is canceled when you change the source to CD,  
TAPE, or AUX, while it is temporarily canceled when you change  
the source to AM.  
• Each time you press the button, the EON data types  
change as follows:  
TA  
NEWS  
INFO  
OFF  
(Canceled)  
TA:  
Traffic announcement  
NEWS: News  
INFO: Program the purpose of which is to impart advice  
in the widest sense.  
OFF: The EON function is canceled. The EON data  
type indicator (TA, NEWS, INFO) goes off.  
3 Press PTY/EON once again.  
The EON data type indicator stops flashing and  
remains lit.  
Now, the EON function is activated. See “How  
the EON function actually works.”  
– 14 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playing Back CDs  
Loading CDs  
Playing Back the Entire Discs — Continuous  
Play  
On the unit ONLY:  
You can play CDs continuously.  
1 Press 0 for the disc tray (CD1 to 3)  
you want to load a CD onto.  
1 Load CDs.  
The unit automatically turns on and the disc  
tray comes out. The Powered Rolling Panel  
also opens automatically.  
3
2 Press one of the disc number  
buttons (CD1, CD2, and CD3) for  
2
the disc you want to play.  
2 Place a disc correctly on the circle of the disc  
1
CD play starts from the first track of the  
tray, with its label side up.  
selected disc.  
Tracks of the currently  
playing disc  
1
2
3
INCORRECT  
CORRECT  
• When using a CD single (8 cm), place it on the inner  
circle of the disc tray.  
Track number  
Elapsed playing time  
3 Press the same 0 you have pressed  
in step 1.  
• Pressing CD £¥8 instead of the disc number buttons  
starts playing back if a CD is on the trays.  
The disc tray closes, and the corresponding  
disc indicator (CD1 to CD3) lights up on the  
display.  
To stop during play, press 7.  
To remove the disc, press 0 for the corresponding disc tray.  
4 Repeat steps 1 to 3 to place other CDs.  
CD playback sequence  
When 3 CDs are loaded on the disc trays, they are played in one of  
the following sequences.  
When loading more than one CD continuously  
When you press 0 for the next tray you want to place another CD  
onto, the first disc tray automatically closes and then the next tray  
comes out.  
• When CD1 is pressed : CD1 ] CD2 ] CD3 (then stops)  
• When CD2 is pressed : CD2 ] CD3 ] CD1 (then stops)  
• When CD3 is pressed : CD3 ] CD1 ] CD2 (then stops)  
* When only 2 CDs are loaded, they are played in the same order,  
but the disc tray without a CD is skipped.  
About the disc indicators  
Each disc indicator corresponds to the disc tray of the same number.  
Basic CD Operations  
While playing a CD, you can do the following operations.  
Disc number  
1
2
3
To exchange CDs during playback of another  
Press 0 corresponding to a CD, not playing or selected  
currently, to eject and exchange the CD.  
Disc indicator  
Disc marker  
If you exchange CDs during play, the current play will not  
stop until all CDs you have exchanged are played.  
• The disc marker lights up for the disc number you have selected.  
• The disc indicator flashes while the corresponding CD is being  
played.  
• The disc indicator goes off when the unit has detected that there is  
no CD on the corresponding disc tray.  
To stop play for a moment  
Press CD £¥8.  
While pausing, the elapsed playing time flashes  
on the display.  
To resume play, press CD £¥8 again.  
– 15 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Continued  
• Each time you press the button, CD play mode changes  
as follows:  
To locate a particular point in a track  
During play, press and hold 1 or ¡.  
1: Fast reverses the disc.  
Random Play  
Program Play  
¡: Fast forwards the disc.  
Continuous Play  
When using the remote control, press and hold  
1 / 4 or ¢ / ¡.  
3
3 Press one of the disc number  
buttons (CD1, CD2, and CD3) to  
select the disc number you want to  
play.  
2
To go to another track  
1
Press 4 or ¢ repeatedly before or during  
playback.  
Track number  
4:Goes back to the beginning of the  
current or previous tracks.  
1
2
3
¢:Skips to the beginning of the next or  
succeeding tracks.  
When using the remote control, press 1 / 4  
or ¢ / ¡.  
Program step number  
Disc number  
If you press and hold 4 / ¢ (or 1 / 4 or ¢ /  
¡ before playing)  
You can change the tracks continuously.  
4 Select a track from the CD selected in the  
above step.  
On the unit:  
Press 4 or ¢ to select the track number,  
To go to another track directly using the number  
buttons  
then press SET.  
Pressing the number button(s) before or  
during play allows you to start playing the  
track number you want.  
Ex.: For track number 5, press 5.  
For track number 15, press +10, then 5.  
For track number 20, press +10, then 10.  
For track number 32, press +10, +10, +10, then 2.  
On the remote control:  
Press the number buttons.  
• For how to use the number buttons, see  
“To go to another track directly using  
the number buttons” described to the  
left.  
Programming the Playing Order of the Tracks  
— Program Play  
You can arrange the order in which the tracks play before you  
start playing. You can program up to 32 tracks.  
• To use Repeat play (see page 17) for Program play, press  
REPEAT after starting Program play.  
1
2
3
1 Load CDs.  
5 Program other tracks you want.  
• To program tracks from the same disc, repeat step 4.  
• To program tracks from a different disc, repeat steps 3  
and 4.  
• If the current playing source is not the CD player, press  
CD £¥8, then 7 before going to the next step.  
2 Press PROGRAM/RANDOM  
repeatedly until “PROGRAM”  
appears on the display.  
6 Press CD £¥8.  
The tracks are played in the order you have programed.  
1
2
3
To stop during play, press 7.  
To exit from Program play mode, press PROGRAM/  
RANDOM repeatedly again before or after play so that the  
unit enters another play mode. (The program you have made  
is stored in memory until you turn off the unit or erase the  
program.)  
• If a program has been stored in memory, the program is  
called up.  
– 16 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To stop during play, press 7.  
• Random play also stops when one of the disc trays is  
opened.  
To check the program contents  
Before playing, you can check the program  
contents by pressing 1 / 4 or ¢ / ¡ on  
the remote control.  
To exit from Random play mode, press PROGRAM/  
RANDOM repeatedly again before or after play so that the  
unit enters another play mode.  
¢ / ¡: Shows the programed tracks in the  
programed order.  
1 / 4: Shows them in the reverse order.  
Even if you press 4 (or 1 / 4 on the remote  
control)  
To modify the program  
Before playing, you can erase the programed tracks  
shown on the display by pressing CANCEL.  
• Each time you press the button, the programed  
track shown on the display is erased from the  
program.  
You cannot go back to the previous tracks during Random play.  
Repeating Tracks or CDs — Repeat Play  
You can have all the CDs, the program or the individual track  
currently playing repeat as many times as you like.  
To add tracks in the program before play, simply select the  
track numbers you want to add by following step 4 of the  
programming procedure on page 16.  
To repeat play, press REPEAT during or before  
playing. To use Repeat play for Program play and  
Random play, press the button after starting  
playback.  
To erase the entire program before or after play, press 7.  
“PROGRAM” appears on the display.  
• Ejecting a CD will also erase the track numbers programed  
from the ejected CD.  
• Each time you press the button, Repeat play mode changes  
as follows, and the following indicator lights up on the  
display:  
If you try to program a 33rd track  
REPEAT ALL  
REPEAT 1CD  
“FULL” will appear on the display.  
Canceled  
(Continuous play)  
REPEAT 1  
If your entry is ignored  
REPEAT ALL: Repeats all the tracks on all the CDs  
(continuously or at random), or all the  
tracks in the program.  
You have tried to program a track from an empty tray, or a  
track number that does not exist on the CD (for example, selecting  
track 14 on a CD that only has 12 tracks). Such entries are ignored.  
REPEAT 1CD*: Repeats all the tracks on one CD.  
REPEAT 1:  
Repeats one track on one CD.  
*
REPEAT 1CD is not used for Program play and Random  
play.  
Playing at Random — Random Play  
The tracks of all loaded CDs will play at random.  
• To use Repeat play for Random play, press REPEAT after  
starting Random play.  
To cancel Repeat play, press REPEAT repeatedly until the  
REPEAT indicator (REPEAT ALL, REPEAT 1CD, or  
REPEAT 1) goes off from the display.  
• Repeat play is also canceled when you select Program play  
or Random play.  
1 Load CDs.  
• If the current playing source is not the CD player, press  
CD £¥8, then 7 before going to the next step.  
Prohibiting Disc Ejection — Tray Lock  
2 Press PROGRAM/RANDOM  
repeatedly until “RANDOM” appears  
on the display.  
You can prohibit CD ejection from the unit and can lock CDs.  
• This operation is possible only using the buttons on the  
unit.  
1
2
3
To prohibit disc ejection, press 0 for any disc tray while  
holding 7. (If there is any disc tray opened, close it first.)  
“LOCKED” appears for a while, and the loaded CDs are  
locked.  
• Each time you press the button, CD play mode changes  
as follows:  
Random Play  
Program Play  
To cancel the prohibition and unlock the CDs, press 0 for  
any disc tray while holding 7.  
“UNLOCKED” appears for a while, and the loaded CDs are  
unlocked.  
Continuous Play  
3 Press CD £¥8.  
The tracks are played at random.  
Random play ends when all the tracks are  
played once.  
If you try to eject CDs  
“LOCKED” appears to inform you that the Tray Lock is in use.  
To skip the currently playing track, press ¢  
(or ¢ / ¡ on the remote control).  
– 17 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playing Back Tapes  
You can play back type I, type II, and type IV tapes without  
changing any settings.  
To play both sides repeatedly — Reverse Mode  
Reverse Mode works for both decks at the same time.  
When it is in use, the tape automatically reverses at the end of  
a side and the unit starts playing the other side of the tape,  
and repeats the same process.  
Playing Back a Tape  
To use Reverse Mode, press REVERSE MODE so  
that the Reverse Mode indicator on the display lights  
up like —  
1 Press EJECT (0) for the deck you want to  
use.  
To cancel Reverse Mode, press the button again so  
that the Reverse Mode indicator on the display lights up like  
For Deck B  
When Reverse Mode is on with cassettes in both decks  
A and B  
For Deck A  
After the reverse (2) side of the tape finishes playing, the tape in the  
other deck starts playing.  
2 Put a cassette in, with the exposed part of the  
tape down.  
Locating the Beginning of a Song — Music  
Scan  
You can use Music Scan to locate the beginning of a song.  
Music Scan searches for blank portions that usually separate  
recorded songs, then plays the next song.  
3 Close the cassette holder gently.  
If you put cassettes in both decks A and B, the last deck  
you have put a cassette into is selected.  
To find the beginning of the current song  
During play, press 1 / ¡ (1 / 4 or  
¢ / ¡ on the remote control) in the  
opposite direction to the tape play.  
The tape direction indicator of the opposite  
direction to the tape play starts flashing  
slowly.  
To operate the other deck, press TAPE A/B.  
4 Press TAPE 2 3.  
The tape play starts and the tape direction  
indicator (2 3) starts flashing slowly to  
indicate the tape running direction.  
• Each time you press the button, the tape  
direction changes.  
Searching stops automatically at the beginning  
of the current song, and the current song starts  
automatically.  
3 : plays the front side.  
2 : plays the reverse side.  
To find the beginning of the next song  
During play, press 1 / ¡ (1 / 4 or ¢ / ¡ on the  
remote control) in the same direction as the tape play.  
The tape direction indicator of the same direction as the tape  
play starts flashing slowly and quickly alternately.  
When the tape plays to the end, the deck automatically stops  
if the Reverse Mode is not on. (See “To play both sides  
repeatedly — Reverse Mode.”)  
To stop during play, press 7.  
Searching stops automatically at the beginning of the next  
song, and the next song starts automatically.  
To operate the other deck, press TAPE A/B, then  
TAPE 2 3.  
Music Scan works by detecting a 4-second long blank  
between each song, so it will not work well in the  
following cases  
To fast wind to the left or to the right, press 1 / ¡  
(1 / 4 or ¢ / ¡ on the remote control) while the  
tape is not running.  
The tape direction indicator (2 3) starts flashing quickly on  
the display.  
• No blank at the beginning of a song.  
• Noise (often caused by much use or poor quality dubbing) which  
fills the blank.  
• Long, very soft passages or pauses in a song.  
To remove the cassette, press 0 EJECT for deck A or  
EJECT 0 for deck B.  
The use of the C-120 or thinner tape is not  
recommended, since characteristic deterioration  
may occur and this tape easily jams in the pinch-  
rollers and the capstans.  
– 18 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording  
IMPORTANT:  
Recording a Tape on Deck B  
It should be noted that it may be unlawful to re-record  
pre-recorded tapes, records, or discs without the  
consent of the owner of copyright in the sound or video  
recording, broadcast or cable programme and in any  
literary, dramatic, musical, or artistic embodied  
therein.  
1 Press EJECT 0 for the deck B.  
• The recording level is automatically set correctly, so it is  
not affected by the VOLUME control (and the  
SUBWOOFER VOLUME control for CA-MXJ750R;  
ACTIVE BASS EX. LEVEL control for CA-MXJ552R,  
CA-MXJ550R, and CA-MXJ500). Thus, during recording  
you can adjust the sound you are actually listening to  
without affecting the recording level.  
• While recording, you can hear sound modes through the  
speakers or headphones. However, the sound is recorded  
without these effects (see page 10).  
2 Put in a recordable cassette, with the exposed  
part of the tape down.  
3 Close the cassette holder gently.  
• If recordings you have made have excessive noise or static,  
the unit may be too close to a TV. Increase the distance  
between the TV and the unit.  
4 Check the tape direction of deck B.  
• If the tape direction is not correct, press TAPE 2 3  
twice then 7 to change the tape direction.  
You can use type I and II tapes for recording.  
5 Start playing the source — FM, AM (LW/  
MW)*, CD player, deck A, or auxiliary  
equipment connected to AUX jacks.  
• When the source is CD, you can also use CD Direct  
Recording (see page 20) and Auto Edit Recording (see  
page 21).  
To protect your recording  
Cassettes have two small tabs  
on the back to protect  
unexpected erasure or re-  
recording.  
To protect your recording, remove these tabs.  
To re-record on a protected tape, cover the holes with  
adhesive tape.  
• When the source is deck A, you can also use the  
dubbing method. (See “Dubbing Tapes” on page 20.)  
* See “To record an AM (LW/MW) station — Beat Cut” on  
page 20.  
When using type II tape, be careful not to cover the holes  
used to detect the tape type.  
6 Start recording.  
To keep the best recording and playback sound quality  
If the heads, capstans, and pinch rollers of the cassette decks  
become dirty, the following will occur:  
• Impaired sound quality  
• Discontinuous sound  
• Fading  
On the unit:  
Press REC START/STOP.  
On the remote control:  
Press and hold REC START/STOP  
for more than 1 second.  
The REC (recording) indicator lights up on the  
display and recording starts.  
• Incomplete erasure  
• Difficulty in recording  
To clean the heads, capstans, and pinch rollers  
Use a cotton swab moistened with alcohol.  
To stop during recording, press REC START/STOP again  
or 7.  
Pinch rollers  
Capstans  
To remove the cassette, press EJECT 0 for deck B.  
To record on both sides — Reverse Mode  
Press REVERSE MODE so that the Reverse Mode  
indicator lights up as —  
• When using the Reverse Mode for recording, start  
recording in the forward (3) direction first.  
Otherwise, recording will stop when recording is done only  
on one side (reverse) of the tape.  
Heads  
To cancel Reverse Mode, press the button again so that the  
Reverse Mode indicator lights up as —  
To demagnetize the heads  
Turn off the unit, and use a head demagnetizer (available at  
electronics and record shops).  
– 19 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Continued  
To record an AM (LW/MW) station — Beat Cut  
While recording an AM (LW/MW) broadcast, beats may be  
heard (which are never heard when listening to the broadcast  
without recording it).  
If this occurs, press PROGRAM/RANDOM  
repeatedly, while recording, until the beats are  
reduced.  
CD Direct Recording  
Everything on the CD goes onto the tape in the order it is on  
the CD, or according to the order you have made for Program  
play.  
1 Put a recordable cassette into deck B.  
• Each time you press the button, the display  
changes to show the following:  
2 Place a disc correctly on the circle of the disc  
tray, with its label side up.  
CUT2  
CUT3  
CUT4  
CUT1  
3 Press one of the disc number  
buttons (CD1 to CD3) to select the  
disc, then 7.  
Dubbing Tapes  
It is preferable that the tape type (type I or II) you record  
from be the same as the tape type you record onto when  
dubbing tapes.  
4 Press CD REC START.  
“CD REC” appears, and the REC (recording)  
indicator lights up on the display.  
Deck B starts recording and the CD player  
starts playing.  
1 Press TAPE 2 3, then 7.  
When the recording is done, “CD REC FINISHED”  
appears on the display, and the CD player and deck B  
stop.  
To stop during CD Direct Recording, press 7 or REC  
START/STOP.  
2 Put the source cassette in deck A, and a  
recordable cassette into deck B.  
To record on both sides — Reverse Mode  
Press REVERSE MODE so that the Reverse Mode  
indicator lights up as —  
• Put the cassettes in both decks so that the tapes will run  
in the forward (3) direction.  
• When using the Reverse Mode for CD Direct  
Recording, start recording in the forward (3)  
direction first. When the tape reaches its end while  
recording a song in the forward direction (3), the last song  
will be recorded at the beginning of the reverse side (2).  
3 Press DUBBING.  
Dubbing starts.  
To stop during dubbing, press 7.  
If you start recording on the reverse side (2), recording  
will stop when recording is done only on one side (reverse)  
of the tape.  
To record on both sides — Reverse Mode  
Press REVERSE MODE so that the Reverse Mode  
indicator lights up as —  
To cancel Reverse Mode, press the button again so that the  
Reverse Mode indicator lights up as —  
To cancel Reverse Mode, press the button again so  
that the Reverse Mode indicator lights up as —  
– 20 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Auto Edit Recording  
4 Press SET.  
By using Auto Edit Recording, you can record the CD tracks  
to fit the tape. Auto Edit Recording makes a program by  
selecting the CD tracks in numerical order. However, to  
prevent the end of the last track on the front side from being  
cut off, the last track is selected so as to fit on the remaining  
tape length.  
Tracks to be recorded on the  
reverse side (SIDE-B) appear.  
1
2
3
On the unit ONLY:  
• Each time you press the button, the tracks to be recorded  
on the front side (SIDE-A) and on the reverse side  
(SIDE-B) alternate.  
1 Load CDs.  
• If the current playing source is not the CD player, press  
CD £¥8, then 7 before going to the next step.  
5 Put a recordable cassette of appropriate  
2 Press EDIT.  
length into deck B.  
1
2
3
6 Press REVERSE MODE so that the  
Reverse Mode indicator lights up as  
.
• Without turning on the Reverse Mode (  
),  
3
3 Press the disc number button  
(CD1 to CD3) for the disc you  
want to record from.  
recording will stop when the front side of the tape is  
recorded.  
2
1
7 Press CD REC START.  
The REC (recording) indicator lights up on the  
display.  
1
2
3
Deck B starts recording then, about 10 seconds  
later, the CD player starts playing.  
When the recording is done, “CD REC FINISHED”  
appears on the display, and the CD player and deck B  
stop.  
• If a tape has not been rewound, deck B will rewind the  
tape before it starts recording.  
• A 10-second blank portion is automatically created at  
the beginning of each side of the tape.  
1
2
3
To stop during Auto Edit Recording  
Press 7 or REC START/STOP so that a 4-second blank  
portion is created on the recorded tape. (Remember a 4-  
second blank is important when using Music Scan — see  
page 18.)  
The optimum tape length for the disc appears.  
To change the tape length manually  
If the tape length selected is not satisfactory, you can  
change the tape length by pressing 4 or ¢.  
You can select the tape length among the following — 40,  
46, 50, 54, 60, 64, 70, 74, 80, 84, and 90.  
To cancel Auto Edit Recording  
Press CANCEL before or after play.  
• Pressing one of the following buttons will also cancel Auto  
Edit Recording — 7, REC START/STOP, and  
PROGRAM/RANDOM.  
– 21 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Timers  
Continued  
There are three timers available — Recording Timer, Daily  
Timer, and Sleep Timer.  
2 Press CLOCK/TIMER again.  
“ON TIME” appears for 2 seconds, then the  
unit enters on-time setting mode.  
Before using the timers, you need to set the clock built in the  
unit. (See page 9.)  
Using Daily Timer  
With Daily Timer, you can wake to your favorite music or  
radio program.  
3 Set the on-time you want the  
unit to turn on.  
1) Press 4 or ¢ to set the hour, then  
How Daily Timer actually works  
The unit automatically turns on, set the volume level to the  
preset level, and starts playing the specified source when the  
press SET.  
2) Press 4 or ¢ to set the minute,  
then press SET.  
on-time comes (the  
indicator flashes just before the on-  
“OFF TIME” appears for 2 seconds,  
then the unit enters off-time setting  
mode.  
time, and continues flashing while the timer is operating).  
Then, when the off-time comes (“OFF” flashes just before the  
off-time), the unit automatically turns off (stands by).  
The timer setting remains in memory until you change it.  
• There is a time limit in doing the following steps. If the  
setting is canceled before you finish, start from step 1  
again.  
• If you have made a mistake while setting timer, press  
CANCEL. (However, this does not always work. If  
CANCEL does not work, press CLOCK/TIMER repeatedly  
and start from step 1 again.)  
4 Set the off-time you want the  
unit to turn off (on standby).  
1) Press 4 or ¢ to set the hour, then  
press SET.  
2) Press 4 or ¢ to set the minute,  
then press SET.  
The unit enters source selecting mode.  
Before you start...  
When using a CD as the source to play, make sure there  
is a CD on the selected disc number tray.  
When using a tape as the source to play —  
– Make sure that a tape is in the deck whose deck  
indicator (A or B) is lit on the display.  
– Make sure that the tape direction is correct.  
When using the external component as the source to  
play, set the timer equipped with the external component  
at the same time.  
5 Press 4 or ¢ to select the  
source to play, then press SET.  
• Each time you press 4 or ¢, the  
source changes as follows:  
TUNER AM  
– CD – –  
TUNER FM  
AUX TAPE  
On the unit ONLY:  
1 Press CLOCK/TIMER until  
“DAILY” appears on the display.  
The DAILY (Daily Timer) indicator also starts  
flashing on the display.  
TUNER FM: tunes into a specified preset FM station.  
= go to step 6.  
TUNER AM: tunes into a specified preset AM (LW/MW)  
station. = go to step 6.  
– CD – –: plays a disc from a specified track of a  
specified disc. = go to step 6.  
TAPE: plays a tape in deck A or B. = go to step 7.  
AUX: plays an external source. = go to step 7.  
• Each time you press the button, the timer setting modes  
change as follows:  
ON TIME  
REC  
DAILY  
Clock  
setting  
Canceled  
ON TIME  
(See page 9.)  
– 22 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Recording Timer  
6 When selecting “– CD – –”  
1) Press 4 or ¢ to select the disc  
number, then press SET.  
With Recording Timer, you can make a tape of a radio  
broadcast automatically.  
2) Press 4 or ¢ to set the track  
number, then press SET.  
How Recording Timer actually works  
The unit automatically turns on, tunes into the specified  
station, sets the volume level to “MIN,” and starts recording  
The unit enters volume setting mode.  
When selecting “TUNER FM” or  
“TUNER AM”  
Press 4 or ¢ to select the preset station number, then  
press SET.  
when the on-time comes (the  
indicator flashes just before  
the on-time, and continues flashing while the timer is  
operating). Then, when the off-time comes (“OFF” appears  
just before the off-time), the unit automatically turns off  
(stands by).  
The unit enters volume setting mode.  
7 Press 4 or ¢ to set the  
volume level.  
The timer setting remains in memory until you change it.  
• There is a time limit in doing the following steps. If the  
setting is canceled before you finish, start from step 1  
again.  
• If you have made a mistake while setting the timer, press  
CANCEL. (However, this does not always work. If  
CANCEL does not work, press CLOCK/TIMER repeatedly  
and start from step 1 again.)  
You can select the volume level from among  
the following — “VOL – –,” “VOL 5,” “VOL 10,”  
and “VOL 15.”  
If you select “ VOL – –,” the volume is set to the last  
level when the unit has been turned off.  
On the unit ONLY:  
1 Put a recordable cassette into deck B.  
2 Press CLOCK/TIMER until “REC”  
8 Press SET to complete the Daily  
Timer setting.  
appears on the display.  
The REC (Recording Timer) indicator also  
starts flashing on the display.  
The DAILY (Daily Timer) indicator stops  
flashing and remains lit. The settings you have  
done are shown on the display in sequence.  
9 Press  
to turn off the unit (on  
standby) if you have set the Daily  
Timer with the unit turned on.  
• Each time you press the button, the timer setting modes  
change as follows:  
To turn on or off Daily Timer after its  
setting is done  
ON TIME  
REC  
DAILY  
1
Press CLOCK/TIMER repeatedly until  
“DAILY” appears on the display.  
Clock  
setting  
Canceled  
ON TIME  
(See page 9.)  
2
To turn off the Daily Timer, press CANCEL.  
The DAILY (Daily Timer) indicator goes off  
from the display (“OFF” appears for a while).  
The Daily Timer is canceled, but the setting for  
the Daily Timer remains in memory.  
3 Press CLOCK/TIMER again.  
“ON TIME” appears for 2 seconds, then the  
unit enters on-time setting mode.  
To turn on the Daily Timer, press SET.  
The DAILY (Daily Timer) indicator lights up  
on the display. The settings you have done are  
shown on the display in sequence for your confirmation.  
If the unit is turned on when the timer-on time comes  
Daily Timer does not work.  
– 23 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Sleep Timer  
4 Set the on-time you want the unit  
to turn on.  
With Sleep Timer, you can fall asleep to music.  
You can set Sleep Timer when the unit is turned on.  
1) Press 4 or ¢ to set the hour, then  
press SET.  
2) Press 4 or ¢ to set the minute, then  
press SET.  
How Sleep Timer actually works  
The unit automatically turns off after the specified time  
length passes.  
“OFF TIME” appears for 2 seconds,  
then the unit enters off-time setting  
mode.  
On the remote control ONLY:  
5 Set the off-time you want the unit  
to turn off (on standby).  
1) Press 4 or ¢ to set the hour, then  
press SET.  
1 Press SLEEP.  
The time length until the shut-off time appears  
and the SLEEP indicator starts flashing on the  
display.  
2) Press 4 or ¢ to set the minute, then  
• Each time you press the button, the time length changes  
as follows:  
press SET.  
The unit enters preset station selecting  
mode.  
10  
20  
30  
60  
90  
120  
Canceled  
2 Wait for about 5 seconds after specifying the  
time length.  
6 Select the preset station.  
1) Press 4 or ¢ to select the band  
(“TUNER FM” or “TUNER AM”),  
then press SET.  
The SLEEP indicator stops flashing and remains lit.  
To check the remaining time until the shut-off time, press  
SLEEP once so that the remaining time until the shut-off time  
appears for about 5 seconds.  
2) Press 4 or ¢ to select a preset  
channel number, then press SET.  
The REC (Recording Timer) indicator  
stops flashing and remains lit. The  
settings you have done are shown on the display in  
sequence.  
To change the shut-off time, press SLEEP repeatedly until  
the desired time length appears on the display.  
To cancel the setting, press SLEEP repeatedly so that the  
SLEEP indicator goes off.  
• Sleep Timer is also canceled when you turn off the unit.  
7 Press  
to turn off the unit (on  
standby) if necessary.  
Timer Priority  
If you want to listen to another source while recording  
Press REC START/STOP to stop recording. Without stopping it, you  
cannot change the source.  
Since each timer can be set separately, you may wonder what  
happens if the setting for these timers overlaps.  
Here are examples.  
To turn on or off Recording Timer after its setting is  
done  
• Recording Timer has priority over Daily Timer and  
Sleep Timer.  
If Daily Timer is set to come on while Recording Timer is  
operating, Daily Timer will not come on at all.  
1
Press CLOCK/TIMER repeatedly until  
“REC” appears on the display.  
2
To turn off the Recording Timer, press  
CANCEL.  
6:00  
6:30  
7:00  
7:30  
The REC (Recording Timer) indicator goes off  
from the display.  
Recording Timer  
Daily Timer  
The Recording Timer is canceled, but the setting  
for the Recording Timer remains in memory.  
does not work.  
If Recording Timer is set to come on while Sleep Timer is  
operating, Sleep Timer will not work (the SLEEP indicator  
does not go off).  
To turn on the Recording Timer, press SET.  
The REC (Recording Timer) indicator lights up  
on the display. The settings you have done are  
shown on the display in sequence for your  
confirmation.  
7:30  
6:00  
6:30  
7:00  
Recording Timer  
Sleep Timer  
does not work.  
– 24 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
To get the best performance of the unit, keep your discs, tapes, and mechanism clean.  
Handling cassette tapes  
Handling discs  
• If the tape is loose in its cassette, take  
up the slack by inserting a pencil in  
one of the reels and rotating.  
• If the tape is loose, it may get  
stretched, cut, or caught in the  
cassette.  
• Remove the disc from its case by  
holding it at the edge while pressing the  
center hole lightly.  
• Do not touch the shiny surface of the  
disc, or bend the disc.  
• Put the disc back in its case after use to  
prevent warping.  
• Be careful not to touch the tape  
surface.  
• Be careful not to scratch the surface of  
the disc when placing it back in its  
case.  
• Avoid exposure to direct sunlight,  
temperature extremes, and moisture.  
• Avoid the following places to store the  
tape:  
— In dusty places  
To clean the disc  
— In direct sunlight or heat  
— In moist areas  
Wipe the disc with a soft cloth in a  
straight line from center to edge.  
— Near a magnet  
DO NOT use any solvent — such as conventional  
record cleaner, spray, thinner, or benzine — to  
clean the disc.  
– 25 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
If you are having a problem with your unit, check this list for a possible solution before calling for service.  
If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person,  
such as your dealer, for service.  
Symptom  
No sound is heard.  
Cause  
Action  
Connections are incorrect or loose.  
Check all connections and make  
corrections. (See pages 6 to 8.)  
Hard to listen to broadcasts because of  
noise.  
• Antennas are disconnected.  
• Reconnect the antennas correctly and  
securely.  
• Change the position and direction of the  
AM (LW/MW) loop antenna.  
• Extend the FM antenna at the best  
position.  
• The AM (LW/MW) loop antenna is too  
close to the unit.  
• The FM antenna is not properly extended  
and positioned.  
The disc sound is discontinuous.  
The disc is scratched or dirty.  
Clean or replace the disc. (See page 25.)  
The disc tray does not open or close.  
• The AC power cord is not plugged in.  
• Trays are locked.  
• Plug the AC power cord.  
• Unlock the trays. (See page 17.)  
The disc does not play.  
The disc is placed upside down.  
Place the disc with the label side up.  
Turn on the unit.  
The cassette holders cannot be opened.  
Power supply from the AC power cord has  
been cut off while the tape was running.  
Impossible to record.  
Small tabs on the back of the cassette are  
removed.  
Cover the holes with adhesive tape.  
Operations are disabled.  
The built-in microprocessor may  
malfunction due to external electrical  
interference.  
Unplug the AC power cord and then plug it  
back in.  
Unable to operate the unit from the remote  
control.  
• The path between the remote control and  
the remote sensor on the unit is blocked.  
• The batteries are exhausted.  
• Remove the obstruction.  
• Replace the batteries.  
– 26 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional Information  
This section is for the model having RDS functions —  
that is CA-MXJ750R, CA-MXJ552R, and  
CA-MXJ550R.  
Description of the PTY codes:  
FINANCE: Stock Market reports, commerce, trading etc.  
CHILDREN: Programs targeted at a young audience.  
NEWS:  
News.  
SOCIAL A: Programs about sociology, history, geography,  
psychology and society.  
AFFAIRS:  
Topical program expanding or enlarging upon the  
news — debate, or analysis.  
RELIGION: Religious programs.  
INFO:  
Program the purpose of which is to impart advice in  
the widest sense.  
PHONE IN: Involving members of the public expressing their  
views either by phone or at a public forum.  
SPORT:  
Program concerned with any aspect of sports.  
TRAVEL:  
LEISURE:  
JAZZ:  
Travel information.  
EDUCATE: Educational programs.  
DRAMA: All radio plays and serials.  
Programs about recreational activities.  
Jazz music.  
CULTURE: Programs concerning any aspect of national or  
COUNTRY: Songs which originate from, or continue the musical  
regional culture, including language, theatre, etc.  
tradition of the American Southern States.  
SCIENCE:  
VARIED:  
Programs about natural sciences and technology.  
NATIONAL: Current popular music of the nation or region in that  
country’s language.  
Used for mainly speech-based programs like  
quizzes, panel games and personality interviews.  
OLDIES:  
FOLK M:  
Music from the so-called “golden age” of popular  
music.  
POP M:  
Commercial music of current popular appeal.  
Rock music.  
Music which has its roots in the musical culture of a  
particular nation.  
ROCK M:  
M.O.R. M:  
Current contemporary music considered to be “easy-  
listening.”  
DOCUMENT:Program concerning factual matters, presented in an  
investigative style.  
LIGHT M:  
Instrumental music, and vocal or choral works.  
TRAFFIC:  
Traffic announcement.  
CLASSICS: Performances of major orchestral works,  
symphonies, chamber music, etc.  
OTHER M: Music not fitting into any of the other categories.  
WEATHER: Weather reports and forecasts.  
Classification of the PTY codes for some FM stations  
may be different from the above list.  
– 27 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
CA-MXJ750R  
CA-MXJ552R/CA-MXJ550R/CA-MXJ500  
Amplifier section  
Amplifier section  
Output Power (IEC 268-3/DIN)  
Output Power (IEC 268-3/DIN)  
SUBWOOFERS:  
65 W per channel, min. RMS, both channels  
driven into 6 at 63 Hz with no more than  
0.9% total harmonic distortion.  
75 W per channel, min. RMS, both channels driven into 6 at 1  
kHz with no more than 0.9% total harmonic distortion.  
Audio input sensitivity/Impedance (at 1 kHz)  
MAIN SPEAKERS: 20 W per channel, min. RMS, both channels  
driven into 6 at 1 kHz with no more than  
0.9% total harmonic distortion.  
AUX:  
420 mV/50 kΩ  
Digital output: CD OPTICAL DIGITAL OUTPUT  
Signal wave length: 660 nm  
Audio input sensitivity/Impedance  
Output level: –15 dBm to –12 dBm  
(at 1 kHz, measured at MAIN SPEAKERS)  
Speakers/Impedance: 6 – 16 Ω  
AUX:  
460 mV/50 kΩ  
Digital output: CD OPTICAL DIGITAL OUTPUT  
Signal wave length: 660 nm  
Tuner  
FM tuning range:  
87.50 MHz – 108.00 MHz  
Output level: –15 dBm to –12 dBm  
AM tuning range: MW: 522 kHz – 1,629 kHz  
LW: 144 kHz – 288 kHz  
Speakers/Impedance: 6 – 16 Ω  
CD player  
Tuner  
CD Capacity:  
3 CDs  
85 dB  
FM tuning range:  
87.50 MHz – 108.00 MHz  
Dynamic range:  
Signal-to-noise ratio: 90 dB  
AM tuning range: MW: 522 kHz – 1,629 kHz  
LW: 144 kHz – 288 kHz  
Wow and flutter:  
Immeasurable  
CD player  
Cassette deck  
Frequency response  
CD Capacity:  
3 CDs  
85 dB  
Dynamic range:  
Normal (type I): 50 Hz — 14,000 Hz  
Signal-to-noise ratio: 90 dB  
CrO2 (type II): 50 Hz — 14,000 Hz  
Wow and flutter:  
Immeasurable  
Metal (type IV): 50 Hz — 14,000 Hz (only for playback)  
Wow and flutter  
0.15% (WRMS)  
Cassette deck  
Frequency response  
Normal (type I): 50 Hz — 14,000 Hz  
CrO2 (type II): 50 Hz — 14,000 Hz  
Metal (type IV): 50 Hz — 14,000 Hz (only for playback)  
General  
Power requirement:  
AC 230 V , 50 Hz  
Power consumption: 95 W (at operation)  
14 W (on standby)  
Wow and flutter  
0.15% (WRMS)  
Dimensions (approx.): 265 mm x 335 mm x 368 mm (W/H/D)  
(107/16 in. x 131/4 in. x 141/2 in.)  
General  
Power requirement:  
AC 230 V , 50 Hz  
Mass (approx.):  
9.7 kg (21.4 lbs)  
Power consumption: 120 W (at operation)  
15 W (on standby)  
Dimensions (approx.): 265 mm x 335 mm x 368 mm (W/H/D)  
(107/16 in. x 131/4 in. x 141/2 in.)  
Supplied accessories  
See page 6.  
Mass (approx.):  
9.9 kg (21.8 lbs)  
Supplied accessories  
See page 6.  
Design and specifications are subject to change without notice.  
Design and specifications are subject to change without notice.  
– 28 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VICTOR COMPANY OF JAPAN, LIMITED  
EN  
J
C
V
0100MWMMDWJEM  
Download from Www.Somanuals.com. All Manuals Search And Download.  

JVC CRT Television 0104KGI II IM User Manual
JVC DVR GR DVL317 User Manual
JVC Projection Television LX D1000 User Manual
JVC TV VCR Combo 1299 TN JII JMT User Manual
Kenwood Stereo Amplifier KAC X520 User Manual
Kenwood Stereo System VR 2080 User Manual
KitchenAid Food Processor 5KFPCB700A User Manual
KitchenAid Food Processor KHB3581 User Manual
KitchenAid Garbage Disposal KBDS100T0 User Manual
KitchenAid Refrigerator W10417002A User Manual