JVC Stereo System CA HXZ9 User Manual

COMPACT COMPONENT SYSTEM  
SISTEMAS DE COMPONENTES COMPACTOS  
SISTEMA DE COMPONENTE COMPACTO  
CA-HXZ9  
INSTRUCTIONS  
MANUAL DE INSTRUCCIONES  
INSTRUÇÕES  
For Customer Use:  
Enter below the Model No. and Serial No.  
which are located either on the rear, bot-  
tom or side of the cabinet. Retain this  
information for future reference.  
Model No.  
Serial No.  
GVT0099-012A  
[UW]  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAUTION  
CAUTION  
Do not block the ventilation openings or holes.  
To reduce the risk of electrical shocks, fire, etc.:  
1. Do not remove screws, covers or cabinet.  
2. Do not expose this appliance to rain or  
moisture.  
(If the ventilation openings or holes are blocked by a  
newspaper or cloth, etc., the heat may not be able to get out.)  
Do not place any naked flame sources, such as lighted  
candles, on the apparatus.  
When discarding batteries, environmental problems must be  
considered and local rules or laws governing the disposal of  
these batteries must be followed strictly.  
Do not expose this apparatus to rain, moisture, dripping or  
splashing and that no objects filled with liquids, such as  
vases, shall be placed on the apparatus.  
PRECAUCIÓN  
PRECAUCIÓN  
Para reducir riesgos de choques eléctricos,  
incendio, etc.:  
No obstruya las rendijas o los orificios de ventilación.  
(Si las rendijas o los orificios de ventilación quedan tapados  
con un periódico, un trozo de tela, etc., no se podrá disipar  
el calor).  
1. No extraiga los tornillos, los cubiertas ni la  
caja.  
No ponga sobre el aparato ninguna llama al descubierto,  
como velas encendidas.  
Cuando tenga que descartar las pilas, tenga en cuenta los  
problemas ambientales y observe estrictamente los  
reglamentos o las leyes locales sobre disposición de las  
pilas.  
2. No exponga este aparato a la lluvia o a la  
humedad.  
No exponga este aparato a la lluvia, humedad, goteos o  
salpicaduras. Tampoco ponga recipientes conteniendo  
liquidos, como floreros, encima del aparato.  
AVISO  
PRECAUÇÃO  
Para reduzir riscos de choques elétricos,  
incêndio, etc.:  
Não obstrua as aberturas e orifícios de ventilação.  
(Se os orifícios ou aberturas de ventilação estiverem  
obstruídos por qualquer papel ou tecido, não haverá  
circulação do ar quente.)  
1. Não remova parafusos e tampas ou  
desmonte a caixa.  
2. Não exponha este aparelho à chuva nem  
à umidade.  
Não coloque nenhum objeto com chamas, como velas  
acesas, sobre o aparelho.  
Ao descartar as baterias, leve em consideração os  
problemas que possam ser causados ao meio ambiente e  
os regulamentos e leis locais e governamentais sobre  
recolhimento dessas baterias devem ser rigorosamente  
seguidos.  
Não exponha este aparelho à chuva, umidade, pingos ou  
esguichos de água, nem coloque em cima do mesmo  
qualquer tipo de recipiente que contenha líquidos, como por  
exemplo vasos.  
G-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Caution: Proper Ventilation  
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:  
1
2
3
Front:  
No obstructions and open spacing.  
Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.  
Bottom:  
Place on the level surface. Maintain an adequate air path for ventilation by placing on a  
stand with a height of 10 cm or more.  
Precaución: El aparato debe estar bien ventilado  
Para evitar posibles riesgos de descargas eléctricas e incendios y prevenir cualquier posible daño, coloque  
el aparato del modo siguiente:  
1
2
Parte delantera: No ponga nada delante, deje el espacio libre.  
Laterales/ parte superior/ parte trasera:  
No se debería colocar nada en las áreas y las distancias que se detallan a continuación.  
3
Parte inferior:  
Coloque el aparato sobre una superficie recta. Debe haber buena circulación de  
aire; para ello, coloque el aparato sobre una base a una altura mínima de 10 cm.  
Precaução: Ventilação adequada  
Para evitar riscos de choques elétricos e incêndios, e prevenir avarias, instale o aparelho como segue:  
1
2
Parte frontal:  
Partes laterais/ Tampa/ Posterior:  
Nenhuma obstrução deverá ser colocada entre as áreas cujas dimensões são indicadas  
Sem obstruções e espaços abertos.  
abaixo.  
3
Parte inferior:  
Instale-o sobre uma superfície plana. Deverá ser mantido espaço suficiente para a  
ventilação se este for instalado numa posição que tenha uma altura de 10 cm ou mais.  
Front view  
Vista frontal  
Vista frontal  
Side view  
Vista lateral  
Vista lateral  
G-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT FOR LASER PRODUCTS  
IMPORTANTE PARA PRODUCTOS LÁSER  
IMPOTANTE PARA PRODUTOS LASER  
REPRODUCTION OF LABELS / REPRODUCCIÓN DE ETIQUETAS / REPRODUÇÃO DE ETIQUETAS  
1 CLASSIFICATION LABEL ON EXTERIOR  
2 WARNING LABEL INSIDE THE UNIT  
SURFACE  
1 ETIQUETA DE CLASIFICACIÓN SOBRE LA  
2 ETIQUETA DE ADVERTENCIA DEL INTERIOR DE  
SUPERFICIE EXTERIOR  
LA UNIDAD  
1 ETIQUETA DE CLASSIFICAÇÃO LOCALIZADA NA  
2 ETIQUETA DE ADVERTÊNCIA LOCALIZADA NA  
SUPERFÍCIE EXTERNA  
PARTE INTERNA DA UNIDADE  
1. CLASS 1 LASER PRODUCT  
2. DANGER:Invisiblelaserradiationwhenopenandinterlock  
failed or defeated. Avoid direct exposure to beam.  
3. CAUTION: Do not open the top cover. There are no user  
serviceable parts inside the Unit; leave all servicing to  
qualified service personnel.  
1. PRODUCTO LÁSER CLASE 1  
2. PELIGRO: En el interior hay radiación láser invisible. Evite  
el contacto directo con el haz.  
3. PRECAUCIÓN: No abra la tapa superior. En el interior de  
la unidad no existen piezas reparables por el usuario; deje  
todo servicio técnico en manos de personal calificado.  
1. PRODUTO LASER CLASSE 1  
2. PERIGO: O laser emite uma rediação invisível que é  
perigosa,casooaparelhoestejaabertoeatravainoperante  
ou danificada. Evite exposição direta ao feixe dos raios.  
3. CUIDADO: Não abra a caixa do aparelho. Não existem  
peçasreparáveispelousuárionaparteinternadaunidade.  
Solicite assistência técnica somente a pessoal técnico  
qualificado.  
G-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
We would like to thank you for purchasing one of our JVC products.  
Before operating this unit, read this manual carefully and thoroughly to  
obtain the best possible performance from your unit, and retain this manual  
for future reference.  
Power sources  
• When unplugging from the wall outlet, always pull the  
plug, not the AC power cord.  
About This Manual  
This manual is organized as follows:  
The manual mainly explains operations using the  
buttons and controls on the unit. You can also use the  
buttons on the remote control if they have the same or  
similar names (or marks) as those on the unit.  
If operation using the remote control is different from  
that using the unit, it is then explained.  
• Basic and common information that is the same for many  
functions is grouped in one place, and is not repeated in  
each procedure. For instance, we do not repeat the  
information about turning on/off the unit, setting the  
volume, changing the sound effects, and others, which are  
explained in the section “Common Operations” on pages 9  
to 12.  
DO NOT handle the AC power cord with wet hands.  
Moisture condensation  
Moisture may condense on the lens inside the unit in the  
following cases:  
• After heating starts in the room  
• In a damp room  
• If the unit is brought directly from a cold to a warm place  
Should this occur, the unit may malfunction. In this case, leave  
the unit turned on for a few hours until the moisture evaporates,  
unplug the AC power cord, and then plug it in again.  
• The following marks are used in this manual:  
Internal heat  
Gives you warnings and cautions to prevent  
from damage or risk of fire/electric shock.  
Also gives you information which is not good  
for obtaining the best possible performance  
from the unit.  
A cooling fan is mounted on the rear panel to prevent heat  
buildup inside the unit.  
For safety, observe the following carefully:  
• Make sure there is good ventilation around the  
unit. Poor ventilation could overheat and damage  
the unit.  
• DO NOT block the cooling fan and the ventilation  
openings or holes. If they are blocked by a  
newspaper or cloth, etc., the heat may not be  
able to get out.  
Gives you information and hints you had better  
know.  
Precautions  
Installation  
• Install in a place which is level, dry and neither too hot nor  
too cold—between 5˚C and 35˚C.  
• Install the unit in a location with adequate ventilation to  
prevent internal heat buildup in the unit.  
• Leave sufficient distance between the unit and the TV.  
• Keep the speakers away from the TV to avoid interference  
with TV.  
Others  
• Should any metallic object or liquid fall into the unit,  
unplug the unit and consult your dealer before operating  
any further.  
• If you are not going to operate the unit for an extended  
period of time, unplug the AC power cord from the wall  
outlet.  
DO NOT disassemble the unit since there are no  
user serviceable parts inside.  
DO NOT install the unit in a location near heat  
sources, or in a place subject to direct sunlight,  
excessive dust or vibration.  
If anything goes wrong, unplug the AC power cord and  
consult your dealer.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Location of the Buttons and Controls ....................... 3  
Front Panel ................................................................. 3  
Remote Control .......................................................... 5  
Getting Started............................................................ 6  
Supplied Accessories.................................................. 6  
Putting the Batteries into the Remote Control ........... 6  
Connecting Antennas ................................................. 6  
Connecting Speakers .................................................. 7  
Connecting Other Equipment..................................... 8  
Adjusting the Voltage Selector ................................... 8  
Common Operations .................................................. 9  
Turning On or Off the Power ..................................... 9  
Canceling the Demonstration ..................................... 9  
Turning On or Off the Key-touch Tone ...................... 9  
Saving the Power Consumption while on Standby  
—Ecology Mode .................................................. 9  
Selecting the Sources................................................... 9  
Setting the Clock ...................................................... 10  
Adjusting the Volume ............................................... 10  
Reinforcing the Bass Sound ..................................... 11  
Reinforcing the Heavy Sound .................................. 11  
Selecting the Sound Modes ...................................... 11  
Creating Your Own Sound Mode—User Mode ....... 12  
Setting the AM Tuner Interval Spacing .................... 12  
Listening to FM and AM Broadcasts ...................... 13  
Tuning in to a Station ............................................... 13  
Presetting Stations .................................................... 13  
Tuning in to a Preset Station .................................... 13  
Playing Back Discs.................................................... 14  
Loading Discs........................................................... 14  
Playing Back the Entire Discs—Continuous Play ... 15  
Basic Disc Operations .............................................. 15  
Programming the Playing Order of the Tracks  
—Program Play .................................................. 16  
Playing at Random—Random Play ......................... 17  
Repeating Tracks or Discs—Repeat Play ................ 18  
Prohibiting Disc Ejection—Tray Lock .................... 18  
Playing Back Tapes ................................................... 19  
Playing Back a Tape ................................................. 19  
Locating the Beginning of a Song—Music Scan ..... 19  
Recording .................................................................. 20  
Recording on a Tape ................................................. 20  
Synchronized Recording .......................................... 21  
Using the Timers ....................................................... 22  
Using Daily Timer .................................................... 22  
Using Recording Timer ............................................ 24  
Using Sleep Timer .................................................... 25  
Timer Priority ........................................................... 25  
Maintenance .............................................................. 26  
Troubleshooting ........................................................ 27  
Specifications............................................................. 28  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Location of the Buttons and Controls  
Become familiar with the buttons and controls on your unit.  
Front Panel  
Front Panel  
Top view of Indication-lamp panel p  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Continued  
Display Window  
TRACK  
See pages in parentheses for details.  
Front Panel  
1 Disc trays  
; CD 3/8 button (9, 15 – 17)  
2
(standby/on) button and lamp (9, 12, 23, 24)  
Pressing this button also turns on the unit.  
a TUNING + / – buttons (13)  
3 ECO (Ecology) button (9)  
4 Remote sensor  
5 Display window  
1 / ¡ (reverse search/forward search) buttons (12, 15, 19)  
7 (stop) button (12, 15 – 21, 24)  
6 FM/AM button (9, 13)  
s VOLUME + / – control (10)  
Pressing this button also turns on the unit.  
7 TAPE 2 3 button (9, 19, 20)  
Pressing this button also turns on the unit.  
8 AUX button (9)  
d Disc play mode buttons (16 – 18)  
• REPEAT and CD PLAY MODE buttons  
f CLOCK/TIMER button (10, 22 – 25)  
g Recording buttons (20, 21, 24)  
Pressing this button also turns on the unit.  
9 SOUND TURBO button (11)  
p Indication-lamp panel  
• REC START/STOP and CD REC START  
h 0 EJECT button for cassette deck (19 – 21)  
Å SOUND TURBO lamp (11)  
ı SUBWOOFER lamp (11)  
Ç REC (recording) lamp (20, 21)  
Î SEA (Sound Effect Amplifier) mode lamps (11)  
• ROCK, POP, and CLASSIC lamps  
Surround mode lamps (11)  
Display Window  
1 Timer indicators  
• DAILY (Daily Timer), SLEEP (Sleep Timer),  
REC (Recording Timer), and  
2 TRACK indicator  
3 Main display  
• Shows the source name, frequency, etc.  
4 PRGM (program) indicator  
5 Disc track number (1 – 16) indicators  
6 RANDOM indicator  
7 REPEAT (ALL/1/DISC) indicators  
8 Audio level indicator  
When one of the 6 preset sound modes is activated, these  
will function as illumination display. For details, see  
“Selecting the Sound Modes” on page 11.  
9 Tuner operation indicators  
• MONO and ST (stereo) indicators  
p Tape operation indicators  
(Timer) indicators  
• DANCE, HALL, and STADIUM lamps  
Ï CD ready lamps (14)  
• CD1 READY, CD2 READY, and CD3 READY lamps  
q SOUND MODE control (11)  
w PRESET + / – control (13)  
4 / ¢ (reverse skip/forward skip) control  
(10, 12, 15 – 17, 22 – 24)  
e SUBWOOFER LEVEL + / – buttons (11)  
r Setting buttons (9, 10, 12, 13, 16, 17, 22 – 25)  
• CANCEL/DEMO and SET/DISPLAY buttons  
t REVERSE MODE button (19 – 21)  
y Cassette holder (19 – 21)  
u PHONES ( ) jack (10)  
i 0 (Disc tray open/close) (CD1, CD2, and CD3) buttons  
(14, 15, 18)  
2 3 (tape direction) and  
(reverse mode) indicators  
Pressing one of these buttons also turns on the unit.  
o Disc number (CD1, CD2, and CD3) buttons (15 – 17, 21)  
Pressing one of these buttons also turns on the unit.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control  
Remote Control  
1 Number buttons (13, 15, 16)  
2 4 (1) (reverse skip/reverse search) button  
(13, 15, 17, 19)  
7 (stop) button (16, 17, 19 – 21, 24)  
¢ (¡) (forward skip/forward search) button  
(13, 15, 17, 19)  
3 Disc number (CD1, CD2, and CD3) buttons (15 – 17)  
Pressing one of these buttons also turns on the unit.  
4 Disc play mode buttons (16 – 18)  
• REPEAT, RANDOM, and PROGRAM buttons  
5 REC START/STOP button (20, 24)  
6 SOUND TURBO button (11)  
7 SUBWOOFER LEVEL + / – buttons (11)  
8 STANDBY/ON  
9 SLEEP button (25)  
p AUX button (9)  
button (9)  
Pressing this button also turns on the unit.  
q FM/AM button (9, 13)  
Pressing this button also turns on the unit.  
w FM MODE button (13)  
e CD 3¥8 button (9, 15 – 17)  
Pressing this button also turns on the unit.  
r PROGRAM CANCEL button (17)  
t TAPE 2 3 button (9, 19, 20)  
Pressing this button also turns on the unit.  
y SOUND MODE button (11)  
u BEEP ON/OFF button (9)  
i VOLUME + / – button (10)  
o FADE MUTING button (10)  
COMPACT  
DIGITAL AUDIO  
When using the remote control, point it  
at the remote sensor on the front panel.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Getting Started  
Continued  
Supplied Accessories  
Connecting Antennas  
FM antenna  
Make sure that you have all the following items.  
The number in the parentheses indicates the quantity of the  
pieces supplied.  
ANTENNA  
FM antenna (supplied)  
• AM loop antenna (1)  
• FM antenna (1)  
• Remote control (1)  
• Batteries (2)  
EXT  
LOOP  
M 75  
AXIAL  
• AC plug adaptor (1)  
If anything is missing, consult your dealer immediately.  
Putting the Batteries into the Remote Control  
1 Attach the FM antenna to the FM 75  
Insert the batteries—R6(SUM-3)/AA(15F)—into the remote  
control, by matching the polarity (+ and –) on the batteries  
with the + and – markings on the battery compartment.  
When the remote control can no longer operate the unit,  
replace both batteries at the same time.  
COAXIAL terminal.  
2 Extend the FM antenna.  
3 Fasten it up in the position which gives you  
the best reception, then fix it on the wall, etc.  
1
About the supplied FM antenna  
The FM antenna supplied with this unit can be used as temporary  
measure. If reception is poor, you can connect an outdoor FM  
antenna.  
To connect an outdoor FM antenna  
Before connecting it, disconnect the supplied FM antenna.  
R6(SUM-3)/AA(15F)  
2
Outdoor FM antenna  
(not supplied)  
3
ANTENNA  
EXT  
LOOP  
M 75  
AXIAL  
DO NOT use an old battery together with a new  
one.  
DO NOT use different types of batteries together.  
DO NOT expose batteries to heat or flame.  
DO NOT leave the batteries in the battery  
compartment when you are not going to use the  
remote control for an extended period of time.  
Otherwise, it will be damaged from battery  
leakage.  
A 75 antenna with coaxial type connector  
(IEC or DIN 45325) should be used.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
AM antenna  
Connecting Speakers  
To connect front speakers and subwoofer  
1
1
2
2
3
Vinyl-covered wire  
(not supplied)  
Speaker cords  
Speaker cords  
3
Blue  
Blue  
Black  
Black  
Black  
Red  
Red  
Speaker  
cords  
from right  
subwoofer  
terminal  
Speaker  
AM loop antenna  
(supplied)  
cords  
from left  
subwoofer  
terminal  
1 If cords are covered with insulation, twist the  
core of the cord at the end of each cord, then  
remove the insulation.  
Subwoofer  
Left  
main speaker  
Right  
main speaker  
2 Connect theAM loop antenna to theAM LOOP  
1 If cords are covered with insulation, twist the  
core of the cord at the end of each cord, then  
remove the insulation.  
terminals as illustrated.  
3 Turn the AM loop antenna until you have the  
best reception.  
2 Insert the end of the speaker cord into the  
terminal as illustrated.  
To connect an outdoor AM antenna  
When reception is poor, connect a single vinyl-covered wire  
to the AM EXT terminal and extend it horizontally. The AM  
loop antenna must remain connected.  
Match the same polarity: (+) to (+) and (–) to (–).  
3 Close the speaker terminals.  
IMPORTANT: Use only speakers with the same speaker  
impedance as indicated by the speaker terminals on the  
rear of the unit.  
For better reception of both FM and AM  
• Make sure the antenna conductors do not touch any other terminals  
and connecting cords.  
• Keep the antennas away from metallic parts of the unit, connecting  
cords, and the AC power cord.  
• DO NOT connect more than one speaker to each  
speaker terminal.  
• DO NOT push or pull the speakers as this will  
damage the foot spacers at the bottom of the  
speakers.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
To connect surround speakers  
By connecting surround speakers to the SURROUND  
SPEAKERS jacks, you can enjoy surround effect.  
Audio equipment  
To audio output  
Right  
Left  
surround  
speaker  
surround  
speaker  
For playing the other equipment through this unit,  
connect between the audio output jacks on the other  
equipment and AUX jacks by using an audio cord (not  
supplied).  
• Connect the right surround speaker to the RIGHT jack.  
• Connect the left surround speaker to the LEFT jack.  
Ideal speaker layout  
To enjoy multichannel sound, locate speakers as follows.  
Adjusting the Voltage Selector  
Before plugging in the unit, set the correct voltage for your  
area with the voltage selector on the rear of the unit.  
Left  
main speaker  
Right  
main speaker  
Subwoofer  
Left  
surround  
speaker  
Right  
surround  
speaker  
Voltage mark  
Use a screwdriver to rotate the voltage selector so that the  
voltage mark is pointing at the same voltage as where you are  
plugging in the unit. (See the back cover page.)  
DO NOT plug in before setting the voltage selector  
on the rear of the unit and all connection  
procedures are complete.  
Connecting Other Equipment  
You can connect audio equipment—used only as a playback  
device.  
DO NOT connect any equipment while the power  
is on.  
DO NOT plug in any equipment until all connections  
are complete.  
Now, you can plug the AC power cord.  
• If the wall outlet does not match the AC plug, use the  
supplied AC plug adaptor.  
• When you connect the AC power cord into a wall outlet,  
the unit automatically starts the demonstration. To cancel  
the demonstration, see “Canceling the Demonstration” on  
page 9.  
Be sure that the plugs of the audio cords are colored: White  
plugs and jacks are for left audio signals, and red ones for  
right audio signals.  
IMPORTANT: Be sure to check all connections to be done  
before plugging the AC power cord into a wall outlet.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Common Operations  
• Each time you press the button, the key-touch tone turns on  
(“BEEP ON”) and off (“BEEP OFF”) alternately.  
Turning On or Off the Power  
To turn on the unit, press  
STANDBY/ON on the remote control)  
(or  
BEEP OFF  
BEEP ON  
so that the lamp on the button goes off.  
Saving the Power Consumption while on Standby  
—Ecology Mode  
To turn off the unit (on standby), press  
You can save the power consumption while the unit is turned  
off (on standby).  
(or STANDBY/ON  
on the remote control)  
again so that the lamp on the button lights up.  
• A little power is always consumed even while  
the unit is on standby.  
You can set Ecology Mode whether the unit is on or off.  
On the unit ONLY:  
ECO  
To activate the Ecology Mode, press ECO.  
To switch off the power supply completely, unplug the AC  
power cord from the AC outlet.  
“ECO” appears on the display for about 2 seconds  
(and the demonstration is canceled if you have  
pressed the button while the unit is off).  
When you unplug the AC power cord or if a power  
failure occurs  
The clock is reset to “0:00” right away, while the tuner preset  
stations (see page 13) will be erased in a few days.  
To deactivate the Ecology Mode, press ECO again.  
“NORMAL” appears on the display for about 2 seconds.  
Canceling the Demonstration  
When connecting the AC power cord into a wall outlet, the  
unit automatically starts the demonstration.  
CANCEL / DEMO  
To cancel the demonstration, press and hold  
CANCEL/DEMO until “DEMO OFF” appears  
on the display.  
• To cancel only beep sounds during the  
• Each time you press the button, “ECO” and “NORMAL”  
appear alternately on the display.  
BEEP  
ON/OFF  
demonstration, press BEEP ON/OFF on the  
remote control.  
When you turn off the unit with Ecology Mode activated  
“ECO” flashes on the display, and the clock time will not be shown  
while the unit is turned off.  
When you press other buttons  
The demonstration stops temporarily. It will start automatically  
again (if no operation is done for 2 minutes) unless you cancel it by  
pressing CANCEL/DEMO.  
Selecting the Sources  
To listen to the FM/AM broadcasts, press FM/AM.  
(See page 13.)  
To play back discs, press CD 3¥8. (See pages 14 – 18.)  
To play back tapes, press TAPE 2 3. (See page 19.)  
To select the external equipment as the source, press AUX.  
To start the demonstration manually  
Press and hold CANCEL/DEMO again until “DEMO START”  
appears on the display.  
TAPE  
CD  
FM / AM  
AUX  
Turning On or Off the Key-touch Tone  
If you do not want the key-touch tone to beep each time you  
press a button, you can deactivate it.  
When you press the play button for a particular source  
(FM/AM, CD 3/8, TAPE 2 3, and AUX), the unit turns on  
and the unit starts playing the source if it is ready.  
On the remote control ONLY:  
BEEP  
Press BEEP ON/OFF.  
ON/OFF  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Continued  
Setting the Clock  
Adjusting the Volume  
You can set the clock whether the unit is on or off; however,  
if Ecology Mode is activated, you cannot set the clock while  
the unit is off (on standby).  
You can adjust the volume level only while the unit is turned  
on. The volume level can be adjusted in 32 steps (VOLUME  
MIN, VOLUME 1 – VOLUME 30, and VOLUME MAX).  
If Ecology Mode is not in use while the unit is turned off (on  
standby), “0:00” flashes on the display until you set the clock.  
Turn VOLUME + / – clockwise (+)  
to increase the volume or  
counterclockwise (–) to decrease it.  
On the unit ONLY:  
CLOCK  
1 Press CLOCK/TIMER.  
/ TIMER  
The hour digits start flashing on the display.  
When using the remote control, press  
VOLUME + to increase the volume or  
VOLUME – to decrease it.  
VOLUME  
2 Turn 4 / ¢ to adjust the  
hour, then press SET/DISPLAY.  
The minute digits start flashing on the  
display.  
For private listening  
Connect a pair of headphones to the PHONES ( ) jack. No sound  
comes out of the speakers. Be sure to turn down the volume before  
connecting or putting on headphones.  
DO NOT turn off (on standby) the unit with the  
volume set to an extremely high level; otherwise, a  
sudden blast of sound can damage your hearing,  
speakers and/or headphones when you turn on the  
unit or start playing any source next time.  
SET /  
DISPLAY  
CANCEL / DEMO  
If you want to correct the hour  
after pressing SET/DISPLAY,  
press CANCEL/DEMO.  
REMEMBER, you cannot adjust the volume level  
while the unit is off (on standby).  
The hour digits start flashing again.  
3 Turn 4 / ¢ to adjust the minute, then  
To turn down the volume level temporarily  
On the remote control ONLY:  
press SET/DISPLAY.  
FADE  
MUTING  
Press FADE MUTING.  
The volume level gradually decreases to  
“VOLUME MIN.”  
To restore the sound, press the button again.  
To check the clock time while playing a source  
Press and hold SET/DISPLAY.  
• Each time you press and hold the button, the source  
indication and the clock time alternate on the display.  
To adjust the clock again  
If you have set the clock before, press CLOCK/TIMER  
repeatedly until the clock setting mode is selected.  
• Each time you press the button, the clock/timer setting  
modes change as follows:  
DAILY  
TIMER  
REC  
(Daily Timer setting)  
Clock  
Canceled  
TIMER  
(Recording Timer setting)  
setting  
(The hour digits start flashing.)  
When you unplug the AC power cord or if a power  
failure occurs  
The clock loses the setting and is reset to “0:00.” If this happens, set  
the clock again.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reinforcing the Bass Sound  
Selecting the Sound Modes  
You can select one of the 5 subwoofer levels. This function  
only affects the playback sound, but does not affect your  
recording. The subwoofer level can be adjusted in 5 steps—  
LEVEL 0 (MIN LEVEL), LEVEL 1, LEVEL 2, LEVEL 3,  
and LEVEL 4 (MAX LEVEL).  
You can select one of the 6 preset sound modes (3 surround  
modes and 3 SEA—Sound Effect Amplifier—modes) and 3  
user modes. This function only affects the playback sound,  
but does not affect your recording. Each Sound Mode has its  
own illumination display.  
U
Press SUBWOOFER LEVEL + to  
To select the sound modes, turn  
O
increase the subwoofer level or  
SUBWOOFER LEVEL – to decrease it.  
SOUND MODE (or press SOUND MODE  
on the remote control) until the sound mode  
you want appears on the display.  
SUBWOOFER  
LEVEL  
SUBWOOFER lamp lights up in red.  
SOUND  
MODE  
CD3 READY  
R O C K  
N C E  
A
D
SUBWOOFER  
R E C  
CD2 READY  
CD1 READY  
L
P
L
O P  
A
H
CLASSIC  
ADIUM  
ST  
• When a sound mode is selected, the lamp for the selected sound  
mode (in this example, DANCE) flashes while the other sound mode  
lamps light up.  
• The SUBWOOFER lamp lights up in red when LEVEL 1 to  
LEVEL 4 (MAX LEVEL) is selected. The lamp turns off when  
LEVEL 0 (MIN LEVEL) is selected.  
CD3 READY  
R O C K  
N C E  
A
D
SUBWOOFER  
R E C  
CD2 READY  
CD1 READY  
L
P
L
O P  
A
H
Reinforcing the Heavy Sound  
CLASSIC  
ADIUM  
ST  
You can enjoy the heavy sound by using Sound Turbo.  
Sound Turbo function boosts the low and high frequency  
sound. This function only affects the playback sound, but  
does not affect your recording.  
• When one of the user modes (USER1, USER2, or USER3) or  
“OFF” is selected, all sound mode lamps go off.  
The sound modes change as follows:  
SOUND  
TURBO  
DANCE  
HALL  
STADIUM  
ROCK  
Press SOUND TURBO.  
“TURBO ON” appears on the display and the  
SOUND TURBO lamp and the SUBWOOFER  
lamp light up.  
OFF  
POP  
(Canceled)  
USER 3  
USER 2  
USER 1  
CLASSIC  
CD3 READY  
R O C K  
N C E  
A
D
When using the remote control, the sound mode changes only  
clockwise in the above sequence.  
SUBWOOFER  
R E C  
CD2 READY  
CD1 READY  
L
P
L
O P  
A
H
CLASSIC  
ADIUM  
ST  
Surround modes*  
DANCE:  
HALL:  
Increases resonance and bass.  
Adds depth and brilliance to the sound.  
• Each time you press SOUND TURBO, Sound Turbo is turned on  
or off.  
STADIUM: Adds clarity and spreads the sound, like in an  
outdoor stadium.  
When you press SUBWOOFER LEVEL + / –, or when  
you select any sound mode while turning on Sound Turbo  
Sound Turbo is canceled.  
SEA (Sound Effect Amplifier) modes  
ROCK:  
Boosts low and high frequency. Good for acoustic  
music.  
POP:  
Good for vocal music.  
CLASSIC: Good for classical music.  
User Modes  
USER 1/2/3: Your individual mode stored in memory. See  
“Creating Your Own Sound Mode—User  
Mode” on page 12.  
OFF:  
The sound mode is canceled.  
* Surround elements are added to the SEA elements to create a  
being-there feeling in your room.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Creating Your Own Sound ModeUser Mode  
5 Turn 4 / ¢ to select one  
of the user modes (USER 1,  
USER 2, or USER 3) in  
which you want to store your  
SEA (Sound Effect Amplifier)  
pattern.  
You can change SEA (Sound Effect Amplifier) pattern to suit  
your preference. The SEA (Sound EffectAmplifier) pattern can  
be adjusted into 5 frequency ranges—LOW1, LOW2, MID,  
HIGH1, and HIGH2. These changed settings can be stored in  
the USER 1, USER 2, and USER 3 modes.  
• There is a time limit in doing the following steps. If the setting  
is canceled before you finish, start from step 1 again.  
SET /  
DISPLAY  
6 Press SET/DISPLAY again.  
On the unit ONLY:  
1 Select one of the preset sound modes.  
If you want to add the surround elements in your SEA  
(Sound Effect Amplifier) pattern, select one of the  
surround modes (DANCE, HALL, or STADIUM) before  
starting the procedure below. (See “Selecting the Sound  
Modes” on page 11.)  
The SEA (Sound Effect Amplifier) pattern you have  
created are stored into the user mode selected in step 5.  
To use your own sound mode  
Select USER 1, USER 2, or USER 3 mode when using the  
sound modes. See “Selecting the Sound Modes” on page 11.  
SET /  
DISPLAY  
2 Press SET/DISPLAY while the  
selected sound mode is still shown  
on the display.  
When you unplug the AC power cord or if a power  
failure occurs  
The setting will be erased in a few days. If this happens, set the user  
modes again.  
Setting the AM Tuner Interval Spacing  
Some countries space AM stations 9 kHz apart, and some  
countries use 10 kHz spacing.  
On the unit ONLY:  
You can only change the AM tuner interval spacing while  
tuning in to an AM station. (See page 13.)  
Current level appears.  
3 Adjust the SEA (Sound Effect  
Press  
while holding down 7.  
Amplifier) pattern.  
1) Turn 4 / ¢ to select the  
frequency range (LOW1, LOW2,  
MID, HIGH1, or HIGH2).  
2) Press 1 or ¡ to adjust the  
level (–3 to +3) of the selected  
frequency range.  
• Each time you press these buttons, the AM tuner interval  
spacing alternates between 9 kHz and 10 kHz.  
3) Repeat steps 1) and 2) to adjust  
the level of the other frequency  
ranges.  
SET /  
DISPLAY  
4 Press SET/DISPLAY again.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening to FM and AM Broadcasts  
On the unit ONLY:  
Tuning in to a Station  
1 Tune in to the station you want to preset.  
FM / AM  
1 Press FM/AM.  
• See “Tuning in to a Station.”  
The unit automatically turns on and tunes in  
to the previously received station (either FM  
or AM).  
SET /  
DISPLAY  
2 Press SET/DISPLAY.  
• Each time you press the button, the band  
alternates between FM and AM.  
2 Start searching for stations.  
On the unit:  
3 Turn PRESET + / – to select a  
Press and hold TUNING +  
or TUNING – for more  
than 1 second.  
preset number.  
On the remote control:  
Press and hold ¢ (¡)  
or 4 (1) for more  
SET /  
DISPLAY  
4 Press SET/DISPLAY again.  
than 1 second.  
The unit starts searching for  
stations and stops when a station of sufficient signal  
strength is tuned in.  
The tuned station in step 1 is stored in the preset number  
selected in step 3.  
• If a program is broadcast in stereo, the ST (stereo) indicator  
lights up.  
• Storing a new station on a used number erases the  
previously stored one.  
To stop searching, press TUNING + or TUNING – (or  
¢ (¡) / 4 (1) on the remote control).  
When you unplug the AC power cord or if a power  
failure occurs  
The preset stations will be erased in a few days. If this happens,  
preset the stations again.  
When you press TUNING + or TUNING – (or ¢ (¡) /  
4 (1) on the remote control) briefly and repeatedly  
The frequency changes step by step.  
To change the FM reception mode  
On the remote control ONLY:  
When an FM stereo broadcast is hard to receive  
or noisy, press FM MODE so that the MONO  
indicator lights up on the display. Reception  
improves.  
Tuning in to a Preset Station  
FM MODE  
FM / AM  
1 Press FM/AM.  
The unit automatically turns on and tunes in  
to the previously received station (either FM  
or AM).  
To restore the stereo effect, press FM MODE again so that  
the MONO indicator goes off. In this stereo mode, you can  
hear stereo sounds when a program is broadcasted.  
• Each time you press the button, the band  
alternates between FM and AM.  
2 Select a preset number.  
On the unit:  
Presetting Stations  
Turn PRESET + / –.  
You can preset 30 FM and 15 AM stations.  
On the remote control:  
In some cases, test frequencies have been already memorized  
for the tuner since the factory examined the tuner preset  
function before shipment. This is not a malfunction. You can  
preset the stations you want into memory by following the  
presetting method.  
• There is a time limit in doing the following steps. If the setting  
is canceled before you finish, start from step 2 again.  
Press the number buttons.  
Ex.: For preset number 5, press 5.  
For preset number 15, press  
+10, then 5.  
1
4
3
6
9
2
5
For preset number 25, press  
+10, +10, then 5.  
For preset number 30, press  
+10, +10, then 10.  
7
8
10  
10  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playing Back Discs  
Continued  
This unit has been designed to play back the following discs:  
• CD (Audio CD)  
Loading Discs  
• CD-R (CD-Recordable)  
• CD-RW (CD-ReWritable)  
On the unit ONLY:  
1 Press 0 for the disc tray  
(CD1, CD2, or CD3) you  
When playing a CD-R or CD-RW  
User-edited CD-Rs (CD-Recordable) and CD-RWs  
(CD-ReWritable) can be played back only if they are already  
“finalized.”  
want to load a disc onto.  
The unit automatically turns on  
and the disc tray comes out.  
You can play back your original CD-Rs or CD-RWs recorded  
in music CD format. (However, they may not be played back  
depending on their characteristics or recording conditions.)  
• Before playing back CD-Rs or CD-RWs, read their  
instructions or cautions carefully.  
2 Place a disc correctly on the circle of the disc  
tray, with its label side up.  
• Some CD-Rs or CD-RWs may not be played back on this  
unit because of their disc characteristics, damage or stain  
on them, or if the player’s lens is dirty.  
• CD-RWs may require a longer readout time. This is caused  
by the fact that the reflectance of CD-RWs is lower than for  
regular discs.  
CORRECT  
INCORRECT  
• When using a CD single (8 cm), place it on the inner  
circle of the disc tray.  
3 Press the same 0 you have  
pressed in step 1.  
About the CD ready lamps  
Each CD ready lamp corresponds to the disc tray of the  
same number.  
The disc tray closes.  
• When they light up?  
4 Repeat steps 1 to 3 to place other discs.  
– When you turn on the unit for the first time after  
plugging into a wall outlet, all CD ready lamps (CD1  
READY, CD2 READY, and CD3 READY) light up.  
From the next time on, CD ready lamp(s) light(s) up  
according to the previous condition.  
– Each time you press the disc tray open/close buttons  
0 (CD1, CD2, and CD3), the corresponding CD  
ready lamp lights up.  
When loading more than one disc  
When you press 0 for the next tray you want to place another disc  
onto, the first disc tray automatically closes and then the next tray  
comes out.  
• When they go off?  
Only when the unit detects there is no disc loaded on a  
certain tray, the corresponding CD ready lamp goes off.  
(“NO DISC 1,” “NO DISC 2,” or “NO DISC 3”  
appears on the display.)  
• When they flash?  
The corresponding CD ready lamp flashes during  
playback and pause.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playing Back the Entire Discs—Continuous Play Basic Disc Operations  
You can play discs continuously.  
While playing a disc, you can do the following operations.  
To exchange discs during playback of another  
Press 0 corresponding to a disc, not  
playing or selected currently, to eject  
and exchange the disc.  
If you exchange discs during play, the  
current play will not stop until all discs  
you have exchanged are played.  
1 Load discs.  
CD3  
CD2  
CD1  
2 Press one of the disc number  
(CD1, CD2, or CD3) buttons  
for the disc you want to play.  
The unit searches for the disc, and  
starts playing with the first track of the  
selected disc.  
To stop play for a moment  
Press CD 3¥8.  
Track number Elapsed playing time  
CD  
While pausing, the elapsed playing time flashes  
on the display.  
TRACK  
1
5
9
2
6
3
7
4
8
10 11 12  
13 14 15 16  
To resume playing, press CD 3¥8 again.  
Tracks of the currently playing disc (Track  
numbers exceeding 16 are not displayed.)  
To go to another track  
Before or during play, turn 4 / ¢ (or press  
4 (1) / ¢(¡) on the remote control).  
4 (or 4 (1)):  
Goes back to the beginning of the  
current or previous tracks.  
¢ (or ¢ (¡)):  
• Pressing CD 3¥8 instead of the disc number buttons  
starts playing back the currently selected disc.  
• If no disc is placed on the selected disc tray, “NO DISC  
1,” “NO DISC 2,” or “NO DISC 3” appears on the  
display. Then, the unit continue searching for a disc  
from the next disc tray.  
Skips to the beginning of the next or succeeding tracks.  
To locate a particular point in a track  
During play, press and hold 1 or  
¡ (or 4 (1) / ¢ (¡) on  
the remote control).  
To stop playing, press 7.  
To remove the disc, press 0 for the corresponding disc tray.  
1 (or 4 (1)):  
Fast-reverses the disc.  
¡ (or ¢ (¡)):  
Disc playback sequence  
When 3 discs* are loaded on the disc trays, they are played in  
one of the following sequences.  
Fast-forwards the disc.  
• When CD1 is pressed: CD1 ] CD2 ] CD3 (then stops)  
• When CD2 is pressed: CD2 ] CD3 ] CD1 (then stops)  
• When CD3 is pressed: CD3 ] CD1 ] CD2 (then stops)  
* When only 2 discs are loaded, they are played in the same  
order, but the disc tray without a disc is skipped.  
To go to another track directly using the number  
buttons  
On the remote control ONLY:  
Pressing the number button(s) before or during play allows  
you to start playing the track number you want.  
Ex.: For track number 5, press 5.  
For track number 15, press +10,  
then 5.  
1
3
6
9
2
4
5
For track number 20, press +10,  
then 10.  
7
8
For track number 32, press +10  
three times, then 2.  
10  
10  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Continued  
Programming the Playing Order of the Tracks  
—Program Play  
4 Select a track from the selected  
disc in step 3.  
On the unit:  
You can arrange the playing order of the tracks before you  
start playing. You can program up to 32 tracks.  
• To use Repeat Play (see page 18) for Program Play, press  
REPEAT after starting Program Play. Only REPEAT 1 and  
REPEAT ALL can be selected for Program Play.  
Turn 4 / ¢ to select the  
track number, then press  
SET/DISPLAY.  
SET /  
DISPLAY  
• There is a time limit in doing the following steps. If the setting  
is canceled before you finish, start from step 2 again.  
1 Load discs.  
On the remote control:  
• If the current playing source is not the CD player, press  
CD 3¥8, then 7 before going to the next step.  
Press the number buttons.  
• For how to use the number  
buttons, see “To go to another  
track directly using the number  
buttons” on page 15.  
1
4
3
6
9
2
5
8
2 Activate the Program Play mode.  
7
On the unit:  
CD PLAY  
MODE  
Press CD PLAY MODE repeatedly  
10  
10  
until “CD PROGRAM” appears on  
the display.  
• Each time you press the button, the play  
mode changes as follows:  
5 Program other tracks you want.  
• To program tracks from the same disc, repeat step 4.  
• To program tracks from a different disc, repeat steps 3  
and 4.  
CD PROGRAM  
CD RANDOM  
Canceled  
(Continuous Play)  
CD  
6 Press CD 3¥8.  
The tracks are played in the order you  
have programed.  
On the remote control:  
PROGRAM  
Press PROGRAM so that  
“CD PROGRAM” appears  
on the display.  
To stop playing, press 7.  
To exit from Program Play mode, press CD PLAY MODE  
repeatedly until the PRGM (program) indicator goes off (or press  
PROGRAM on the remote control) after playback stops.  
P R G M  
• The PRGM (program) indicator lights up on the display.  
• If you try to program a 33rd track, “CD FULL” will appear on the  
display.  
• If you have tried to program a track from an empty tray, “NO  
DISC 1,” “NO DISC 2,” or “NO DISC 3” will appear on the  
display for about 2 seconds.  
If a program has been stored in memory, the program is  
called up.  
CD3  
• If the track number you have programed does not exist on the  
disc, it will be skipped during play.  
3 Press one of the disc number  
CD2  
(CD1, CD2, or CD3) buttons  
CD1  
to select the disc you want to  
play.  
Track number  
P R G M  
Disc number  
Program step number  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To check the program contents  
On the remote control ONLY:  
Playing at Random—Random Play  
The tracks of the currently selected disc will be played at  
random.  
Before playing, you can check the  
program contents by pressing  
• To use Repeat Play (see page 18) for Random Play, press  
REPEAT after starting Random Play. Only REPEAT 1 and  
REPEAT ALL can be selected for Random Play.  
4 (1) or ¢ (¡).  
4 (1) : Shows the programed  
tracks in the reverse order.  
¢ (¡) : Shows them in the programed order.  
1 Load a disc.  
To modify the program  
2 Press the corresponding disc number (CD1,  
CD2, or CD3) button where the disc is loaded  
in step 1, then press 7.  
CANCEL / DEMO  
Before or after playing, you can erase the last  
programed tracks by pressing CANCEL/DEMO  
(or press PROGRAM CANCEL on the remote  
control).  
CD3  
CD2  
CD1  
PROGRAM  
CANCEL  
• Each time you press the button, the last  
programed track is erased from the program.  
3 Activate the Random Play mode.  
To add tracks in the program before playing, simply select  
the track numbers you want to add by following step 4 of the  
programming procedure. If you want to add tracks from  
another disc, follow steps 3 and 4.  
On the unit:  
CD PLAY  
MODE  
Press CD PLAY MODE repeatedly  
until “CD RANDOM” appears on  
the display.  
• Each time you press the button, the play mode changes  
as follows:  
To erase the entire program before or after playing, press  
and hold 7 until “CD PROGRAM” appears on the display.  
• The program you have made will be erased,  
– when you unplug the AC power cord, or  
CD PROGRAM  
CD RANDOM  
– when a power failure occurs.  
Canceled  
(Continuous Play)  
On the remote control:  
RANDOM  
Press RANDOM so that  
“CD RANDOM”  
appears on the display.  
1
5
9
2
6
3
7
4
8
10 11 12  
RANDOM  
• The RANDOM indicator also lights up on the display.  
CD  
4 Press CD 3¥8.  
The tracks are randomly played.  
Random Play ends when all the tracks  
of the all loaded discs are played once.  
To skip the currently playing track, turn 4 / ¢ to the  
right (or press ¢ (¡) on the remote control).  
If you turn 4 / ¢ to the left (or press 4 (1) on  
the remote control)  
You cannot go back to the previous tracks during Random Play.  
To stop playing, press 7.  
To exit from Random Play mode, press CD PLAY MODE  
repeatedly until the RANDOM indicator goes off (or press  
RANDOM on the remote control) after playback stops.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Repeating Tracks or Discs—Repeat Play  
Prohibiting Disc Ejection—Tray Lock  
You can have all the discs, the program or the individual track You can prohibit disc ejection from the unit and lock discs.  
currently playing repeat as many times as you like.  
• This operation is possible only when the source is the CD  
player.  
REPEAT  
To repeat playing, press REPEAT during or  
before play.  
• Each time you press the button, Repeat Play mode  
changes as follows:  
On the unit ONLY:  
To prohibit disc ejection, press 0 for any disc tray while  
holding down 7. (If there is any disc tray opened, close it  
first.)  
REPEAT ALL  
REPEAT 1DISC  
Canceled  
REPEAT 1  
The Repeat Play mode indicator lights up on the display.  
TRACK  
4
5
9
6
7
8
10 11 12  
13 14 15 16  
“LOCKED” appears for a while on the display, and the loaded  
discs are locked.  
REPEAT ALL: During Continuous Play  
Repeats all the tracks on all the loaded  
discs continuously.  
During Program Play  
Repeats the program.  
To cancel the prohibition and unlock the discs, press 0 for  
any disc tray while holding down 7.  
“UNLOCKED” appears for a while on the display, and the  
loaded discs are unlocked.  
During Random Play  
Repeats all the tracks on all the loaded  
discs randomly.  
REPEAT 1DISC: Repeats all the tracks on the current disc  
continuously.  
REPEAT 1:  
Repeats the currently playing track.  
To cancel Repeat Play, press REPEAT repeatedly until the  
Repeat Play mode indicators go off from the display.  
If you try to eject discs while Tray Lock is in use  
“LOCKED” appears to inform you that the disc trays are locked.  
“REPEAT 1DISC” cannot be selected for Program  
Play or Random Play  
It is canceled when you select Program Play or Random Play.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
2 : plays the reverse side.  
• If no cassette is inserted, “NO TAPE” appears on the  
display.  
When the tape plays to the end, the deck automatically  
stops if the Reverse Mode is off. (See “To play both sides  
repeatedly—Reverse Mode.”)  
             
Playing Back Tapes  
You can play back type I tapes without changing any settings.  
To play both sides repeatedly—Reverse Mode  
When using Reverse Mode, the tape automatically reverses at  
the end of one side, starts playing the other side of the tape,  
and repeats the same process.  
Playing Back a Tape  
On the unit ONLY:  
To use Reverse Mode, press REVERSE MODE  
1 Press 0 EJECT for the cassette deck.  
REVERSE  
MODE  
so that the Reverse Mode indicator lights up on the  
display like—  
.
To cancel Reverse Mode, press the button again so that the  
Reverse Mode indicator lights up on the display like—  
.
Locating the Beginning of a Song—Music Scan  
2 Insert a cassette with the exposed part of the  
You can use Music Scan to locate the beginning of a song.  
Music Scan searches for blank portions that usually separate  
recorded songs, then plays the next song.  
tape down.  
To find the beginning of the current song  
During play, press 1 or ¡  
(or 4 (1) / ¢ (¡) on the  
remote control) in the opposite  
direction to the tape play.  
The tape direction indicator of the  
opposite direction to the tape play starts flashing intermittently.  
3 Close the cassette holder gently.  
Searching stops automatically at the beginning of the current  
song, and it starts automatically.  
TAPE  
4 Press TAPE 2 3.  
The tape play starts and the tape direction  
indicator (3 or 2) starts flashing slowly  
to indicate the tape running direction.  
• Each time you press the button, the tape direction changes  
and “REVERSE” appears for a while on the display.  
3 : plays the front side.  
To find the beginning of the next song  
During play, press 1 or ¡  
(or 4 (1) / ¢ (¡) on the  
remote control) in the same direction  
as the tape play.  
The tape direction indicator of the  
same direction as the tape play starts flashing intermittently.  
Searching stops automatically at the beginning of the next  
song, and it starts automatically.  
Music Scan works by detecting a 4-second long blank  
between each song, so it will not work well in the  
following cases  
To stop playing, press 7.  
To fast-wind to the left or to the right, press 1 or ¡ (or  
4 (1) / ¢ (¡) on the remote control) while the tape  
is not running.  
The tape direction indicator (3 or 2) starts flashing quickly  
on the display.  
• No blank at the beginning of a song.  
• Noise (often caused by much use or poor quality dubbing) which  
fills the blank.  
• Long, very soft passages or pauses in a song.  
To remove the cassette, press 0 EJECT to open the cassette  
holder only while the tape is not running.  
The use of the C-120 or thinner tape is not  
recommended, since characteristic deterioration  
may occur and this tape easily jams in the pinch-  
rollers and the capstans.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording  
Continued  
IMPORTANT:  
Recording on a Tape  
It may be unlawful to record or play back copyrighted  
material without the consent of the copyright owner.  
• The recording level is automatically set correctly, so it is not  
affected by the VOLUME, the SUBWOOFER LEVEL, and  
the SOUND MODE controls, or the SOUND TURBO button.  
Thus, during recording you can adjust the sound you are  
actually listening to without affecting the recording level.  
• If there are excessive noise or static in the recording you  
have made, the unit may be too close to a TV. Increase the  
distance between the TV and the unit.  
1 Press 0EJECT and insert a recordable cassette  
with the exposed part of the tape down.  
You can use type I tape for recording.  
To protect your recording  
2 Close the cassette holder gently.  
• If you want to record on both sides of a tape, see “To  
record on both sides—Reverse Mode.”  
Cassettes have two small tabs  
on the back to protect from  
unexpected erasure or re-  
recording.  
3 Check the tape direction of the cassette deck.  
• If the tape direction is not correct, press TAPE 2 3 twice  
then 7 to change the tape direction.  
To protect your recording,  
remove these tabs.  
To re-record on a protected tape, cover the holes with  
adhesive tape.  
4 Start playing the source—FM, AM, CD player  
or auxiliary equipment connected to AUX jacks.  
• When the source is the CD player, you can also use  
Synchronized Recording (see page 21).  
To keep the best recording and playback sound  
quality  
If the heads, capstans, and pinch rollers of the cassette deck  
become dirty, the following will occur:  
• Impaired sound quality  
5 Start recording.  
On the unit:  
REC START  
/ STOP  
Press REC START/STOP.  
• Discontinuous sound  
On the remote control:  
Press and hold REC START/STOP  
for more than 1 second.  
• Fading  
• Incomplete erasure  
• Difficulty in recording  
The REC (recording) lamp flashes when recording starts,  
and the tape direction indicator (3 or 2) starts flashing  
slowly.  
To clean the heads, capstans, and pinch rollers  
Use a cotton swab moistened with alcohol.  
• If no cassette is inserted, “NO TAPE” appears on the  
display. If a protected tape is inserted, “NO REC”  
appears on the display.  
Pinch rollers  
Capstans  
To stop recording immediately, press REC START/STOP  
on the unit or 7 (or press and hold REC START/STOP on  
the remote control for more than 1 second).  
To remove the cassette, press 0 EJECT to open the cassette  
holder only while the tape is not running.  
Heads  
To demagnetize the heads  
Turn off the unit, and use a head demagnetizer (available at  
electronics and audio shops).  
To record on both sides—Reverse Mode  
On the unit ONLY:  
REVERSE  
MODE  
Press REVERSE MODE so that the Reverse Mode  
indicator lights up on the display like—  
.
• When using the Reverse Mode for recording,  
start recording in the forward (3) direction first.  
Otherwise, recording will stop when only one side (reverse)  
of the tape is recorded.  
To cancel Reverse Mode, press the button again so that the  
Reverse Mode indicator lights up on the display like—  
.
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD REC  
START  
Synchronized Recording  
4 Press CD REC START.  
“CD REC” appears on the display and the  
REC (recording) lamp flashes when recording  
starts.  
By using the Synchronized Recording method, everything on  
the disc goes onto the tape in the same order as it is on the  
disc, or according to the order you have set in Program Play.  
You can start or stop both disc play and tape recording at the  
same time.  
The cassette deck starts recording while the  
CD player starts playing.  
When the recording is done, “CD REC FINISHED”  
appears scrolling on the display, and the REC (recording)  
lamp turns off. Both the cassette deck and the CD player  
stop automatically.  
On the unit ONLY:  
To stop recording, press 7 to create a 4-second  
blank portion on the recording tape. (Remember,  
a 4-second blank is important when using Music  
Scan—see page 19.)  
1 Press 0EJECT and insert a recordable cassette  
with the exposed part of the tape down.  
To remove the cassette, press 0 EJECT to open the cassette  
holder only while the tape is not running.  
To record on both sides—Reverse Mode  
On the unit ONLY:  
Press REVERSE MODE so that the Reverse Mode  
REVERSE  
MODE  
indicator lights up on the display like—  
.
2 Load a disc.  
3 Select a disc.  
• When using the Reverse Mode for  
Synchronized Recording, start recording in the  
forward (3) direction first. When the tape reaches its end  
while recording a song in the forward direction (3), the  
last song will be re-recorded at the beginning of the reverse  
side (2).  
CD3  
Press the corresponding disc number  
(CD1, CD2, or CD3) button where a  
disc is loaded in step 2, then press 7.  
CD2  
CD1  
If you start recording on the reverse side (2) first,  
recording will stop when only one side (reverse) of the tape  
is recorded.  
To cancel Reverse Mode, press the button again so that the  
Reverse Mode indicator lights up on the display like—  
.
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Timers  
Continued  
There are three timers available—DAILY (Daily Timer), REC  
(Recording Timer), and SLEEP (Sleep Timer).  
On the unit ONLY:  
CLOCK  
/ TIMER  
1 Press CLOCK/TIMER  
repeatedly until “DAILY”  
appears on the display.  
You can set the timers whether the unit is on or off; however,  
if Ecology Mode is activated, you cannot set the timers while  
the unit is off.  
The  
(Timer) indicator lights up and the  
Before using the timers, set the clock built in the unit. (See  
page 10.)  
DAILY (Daily Timer) indicator also starts  
flashing on the display.  
D
A
I
L Y  
Using Daily Timer  
With Daily Timer, you can be wake up with your favorite  
music or radio program.  
• Each time you press the button, the timer setting modes  
change as follows:  
DAILY  
TIMER  
REC  
How Daily Timer actually works  
(Daily Timer setting)  
The unit automatically turns on, sets the volume level to the  
preset level, and starts playing the specified source when the  
on-time comes. (“DAILY” and the DAILY indicator flash just  
before the on-time, and the DAILY indicator continues  
flashing while the timer is operating.) Then, when the off-  
time comes (“DAILY OFF” flashes just before the off-time),  
the unit automatically turns off (on standby).  
Clock  
Canceled  
TIMER  
(Recording Timer setting)  
setting  
(The hour digits start flashing.)  
CLOCK  
/ TIMER  
2 Press CLOCK/TIMER again.  
“TIMER” appears for about 2 seconds,  
then the unit enters on-time setting mode.  
The Daily Timer works everyday automatically. If you do not  
want to use the Daily Timer, turn it off. (See “To turn on or  
off Daily Timer after its setting is done” on page 23.) The  
timer setting remains in memory until you change it.  
• There is a time limit in doing the following steps. If the setting  
is canceled before you finish, start from step 1 again.  
• To correct a misentry while setting the timer, press  
CANCEL/DEMO.  
D
A
I
L Y  
3 Set the on-time you want the  
unit to turn on at.  
1) Turn 4 / ¢ to set the hour, then  
press SET/DISPLAY.  
2) Turn 4 / ¢ to set the minute,  
then press SET/DISPLAY.  
Before you start...  
“SET” appears for about 1 second, then  
the unit enters off-time setting mode.  
When using a disc as the source to play—  
– Make sure there is a disc on the selected disc tray.  
When using a tape as the source to play—  
– Make sure that a tape is in the cassette deck.  
– Make sure that the tape direction is correct.  
When using the external component as the source to  
play—  
SET /  
DISPLAY  
D
A
I
L Y  
Set the timer equipped on the external component at  
the same time.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET /  
DISPLAY  
8 Press SET/DISPLAY to complete  
4 Set the off-time you want the unit to turn off  
the Daily Timer setting.  
(on standby) at.  
The DAILY (Daily Timer) indicator stops  
flashing and remains lit. “OK ” appears on  
the display for about 2 seconds.  
The settings you have done are shown on the  
display in sequence for your confirmation.  
1) Turn 4 / ¢ to set the hour, then press  
SET/DISPLAY.  
2) Turn 4 / ¢ to set the minute, then press  
SET/DISPLAY.  
“SET” appears for about 1 second, then the unit enters  
source selecting mode.  
9 Press  
to turn off the unit (on  
standby) if you have set the Daily  
Timer with the unit turned on.  
D
A
I
L Y  
5 Turn 4 / ¢ to select the source to play,  
then press SET/DISPLAY.  
“SET” appears for about 1 second.  
• The source changes as follows:  
• If the unit is turned on before the on-time comes  
Daily Timer does not work.  
• Even if you unplug the AC power cord or if a power failure  
occurs  
TUNER FM  
TUNER AM  
Once you set the timer, the timer setting may remain stored in  
memory in a few days. (Check whether the timer setting still  
remains or not.)  
AUX IN  
TAPE  
1 CD-- 1  
TUNER FM: tunes in to a specified preset FM station.  
= Go to step 6.  
TUNER AM: tunes in to a specified preset AM station.  
= Go to step 6.  
To turn on or off Daily Timer after its setting is done  
1 CD-- 1:  
plays from a specified track of a specified  
disc. = Go to step 6.  
CLOCK  
1Press CLOCK/TIMER repeatedly until  
“DAILY” appears on the display.  
/ TIMER  
TAPE:  
plays a tape in the cassette deck.  
= Go to step 7.  
The DAILY (Daily Timer) indicator starts  
flashing on the display and  
indicator remains lit.  
(Timer)  
AUX IN:  
plays an external source. = Go to step 7.  
CANCEL / DEMO  
2To turn off the Daily Timer, press  
CANCEL/DEMO.  
6 When selecting “TUNER FM” or “TUNERAM”  
Turn 4 / ¢ to select the preset station number, then  
press SET/DISPLAY.  
The DAILY (Daily Timer) and  
indicators go off from the display (“DAILY  
OFF” appears for a while).  
(Timer)  
The unit enters volume setting mode.  
When selecting “1 CD-- 1”  
1) Turn 4 / ¢ to select the disc number, then press  
SET/DISPLAY.  
“SET” appears for about 1 second.  
2) Turn 4 / ¢ to set the track number, then press  
SET/DISPLAY.  
The Daily Timer is canceled, but the setting for the Daily  
Timer remains in memory.  
Or  
SET /  
DISPLAY  
To turn on the Daily Timer, press  
SET/DISPLAY.  
“SET” appears for about 1 second, then the unit enters  
volume setting mode.  
“OK ” appears on the display for about 2  
seconds.  
The settings you have done are shown on the  
display in sequence for your confirmation.  
7 Turn 4 / ¢ to set the  
volume level.  
• The volume level changes as follows:  
— —  
VOLUME  
VOLUME 5  
VOLUME 15  
VOLUME 10  
• If you select “VOLUME – –,” the volume is set to the  
last level when the unit has been turned off.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Continued  
4 Set the on-time you want the  
Using Recording Timer  
unit to turn on at.  
With Recording Timer, you can make a tape of a radio  
broadcast automatically.  
1) Turn 4 / ¢ to set the hour, then  
press SET/DISPLAY.  
2) Turn 4 / ¢ to set the minute,  
then press SET/DISPLAY.  
“SET” appears for about 1 second,  
then the unit enters off-time setting  
mode.  
How Recording Timer actually works  
The unit automatically turns on, tunes in to the specified  
station, sets the volume level to “VOLUME MIN,” and starts  
recording when the on-time comes (“REC” and the REC  
indicator flash just before the on-time, and the REC indicator  
continues flashing while the timer is operating). Then, when  
the off-time comes (“REC OFF” flashes just before the off-  
time), the unit automatically turns off (on standby).  
The timer setting remains in memory until you change it.  
• There is a time limit in doing the following steps. If the setting  
is canceled before you finish, start from step 2 again.  
• To correct a misentry while setting the timer, press  
CANCEL/DEMO.  
SET /  
DISPLAY  
R E C  
5 Set the off-time you want the unit to turn off  
(on standby) at.  
1) Turn 4 / ¢ to set the hour, then press  
SET/DISPLAY.  
On the unit ONLY:  
2) Turn 4 / ¢ to set the minute, then press  
SET/DISPLAY.  
1 Insert a recordable cassette with the exposed  
“SET” appears for about 1 second, then the unit enters  
preset station selecting mode.  
part of the tape down.  
CLOCK  
2 Press CLOCK/TIMER  
/ TIMER  
6 Select the preset station.  
repeatedly until “REC” appears  
on the display.  
1) Turn 4 / ¢ to select the band (“TUNER FM” or  
“TUNER AM”), then press SET/DISPLAY.  
“SET” appears for about 1 second.  
2) Turn 4 / ¢ to select a preset channel number,  
then press SET/DISPLAY.  
The  
(Timer) indicator lights up and the  
REC (Recording Timer) indicator also starts flashing on  
the display.  
The REC (Recording Timer) indicator stops flashing  
and remains lit. “OK ” appears on the display for  
about 2 seconds.  
R E C  
The settings you have done are shown on the display  
in sequence for your confirmation.  
• Each time you press the button, the timer setting modes  
change as follows:  
7 Press  
to turn off the unit (on  
standby) if necessary.  
DAILY  
TIMER  
REC  
(Daily Timer setting)  
Clock  
Canceled  
TIMER  
(Recording Timer setting)  
setting  
(The hour digits start flashing.)  
CLOCK  
/ TIMER  
3 Press CLOCK/TIMER again.  
“TIMER” appears for about 2 seconds,  
then the unit enters on-time setting mode.  
• If you want to listen to another source while recording  
Press REC START/STOP or 7 to stop recording. Without  
stopping it, you cannot change the source.  
• Even if you unplug the AC power cord or if a power failure  
occurs  
R E C  
Once you set the timer, the timer setting may remain stored in  
memory for a few days. (Check whether the timer setting still  
remains or not.)  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To check the remaining time until the shut-off time, press  
SLEEP once so that the remaining time (minute) until the  
shut-off time appears for about 5 seconds.  
To turn on or off Recording Timer after its setting  
is done  
CLOCK  
1Press CLOCK/TIMER repeatedly until  
/ TIMER  
“REC” appears on the display.  
To change the shut-off time, press SLEEP repeatedly until  
The REC (Recording Timer) indicator starts  
the desired time length appears on the display.  
flashing on the display and the  
indicator remains lit.  
(Timer)  
To cancel the setting, press SLEEP repeatedly so that the  
SLEEP indicator goes off.  
• Sleep Timer is also canceled when you turn off the unit.  
CANCEL / DEMO  
2To turn off the Recording Timer, press  
CANCEL/DEMO.  
The REC (Recording Timer) indicator goes  
off from the display (“REC OFF” appears on  
the display for about 2 seconds).  
Timer Priority  
The Recording Timer is canceled, but the setting for the  
Recording Timer remains in memory.  
Since each timer can be set separately, you may wonder what  
happens if the settings for these timers overlap.  
Or  
Below are some examples.  
SET /  
DISPLAY  
To turn on the Recording Timer, press  
SET/DISPLAY.  
“OK ” appears on the display for about 2  
seconds.  
The settings you have done are shown on the  
display in sequence for your confirmation.  
Recording Timer has priority over Daily Timer and Sleep Timer.  
• If Daily Timer is set to come on while Recording Timer is  
operating, Daily Timer will not come on at all.  
6:00  
6:30  
7:00  
7:30  
Recording Timer  
Daily Timer  
does not work.  
Using Sleep Timer  
• If Recording Timer is set to come on while Sleep Timer is  
operating, Sleep Timer will be canceled.  
With Sleep Timer, you can fall asleep to music. You can set  
Sleep Timer only while the unit is turned on.  
21:00  
21:30 22:00  
22:30  
Recording Timer  
Sleep Timer  
How Sleep Timer actually works  
The unit automatically turns off after the specified time  
length passes.  
canceled.  
On the remote control ONLY:  
SLEEP  
1 Press SLEEP.  
The time length until the shut-off time  
appears and the SLEEP indicator starts  
flashing on the display.  
• Each time you press the button, the time length changes  
as follows:  
SLEEP 10 SLEEP 20 SLEEP 30 SLEEP 60  
Canceled  
SLEEP 120  
SLEEP 90  
• If the built-in clock has not been set, “CLOCK ADJUST”  
appears on the display.  
2 Wait for about 5 seconds after specifying the  
time length.  
The SLEEP indicator flashes slowly until Sleep Timer  
works.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
To get the best performance of the unit, keep your discs, tapes, and mechanism clean.  
Handling cassette tapes  
General Notes  
In general, you will have the best performance by keeping  
your discs and the mechanism clean.  
• If the tape is loose in its cassette, take  
up the slack by inserting a pencil in one  
of the reels and rotating.  
• If the tape is loose, it may get stretched,  
cut, or caught in the cassette.  
• Store discs in their cases, and keep them in cabinets or on  
shelves.  
• Keep the unit’s disc trays closed when not in use.  
• Be careful not to touch the tape surface.  
Handling discs  
• Remove the disc from its case by  
holding it at the edge while pressing  
the center hole lightly.  
• Avoid the following places to store the  
tape:  
— In dusty places  
— In direct sunlight or heat  
— In moist areas  
• Do not touch the shiny surface of the  
disc, or bend the disc.  
• Put the disc back in its case after use  
to prevent warping.  
— Near a magnet  
• Be careful not to scratch the surface  
of the disc when placing it back in its  
case.  
• Avoid exposure to direct sunlight,  
temperature extremes, and moisture.  
Cleaning the unit  
• Stains on the unit  
Should be wiped off with a soft cloth. If the unit is heavily  
stained, wipe it with a cloth soaked in water diluted neutral  
detergent and wrung well, then wipe clean with a dry cloth.  
To clean the disc  
Wipe the disc with a soft cloth in a  
straight line from center to edge.  
• Since the unit may deteriorate in quality, become  
damaged or get its paint peeled off, be careful about the  
following:  
— DO NOT wipe it with a hard cloth.  
— DO NOT wipe it strong.  
— DO NOT wipe it with thinner or benzine.  
— DO NOT apply any volatile substance such as  
insecticides to it.  
— DO NOT allow any rubber or plastic to remain in  
contact with it for a long time.  
Continued use of irregular shape discs  
(heart-shape, octagonal, etc.) can  
damage the unit.  
DO NOT use any solvent—such as conventional  
record cleaner, spray, thinner, or benzine—to clean  
the disc.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
If you are having a problem with your unit, check this list for a possible solution before calling for service.  
If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person,  
such as your dealer, for service.  
Symptom  
Cause  
Action  
Unable to cancel the demonstration. The button other than CANCEL/DEMO Press CANCEL/DEMO on the unit.  
is pressed to cancel the demonstration  
temporarily.  
(See page 9.)  
No sound is heard.  
Connections are incorrect or loose.  
Check all connections and make  
corrections. (See pages 6 to 8.)  
Operations are disabled.  
The built-in microprocessor may  
malfunction due to external electrical  
interference.  
Unplug the AC power cord and then  
plug it back in.  
Unable to operate the unit from the • The path between the remote control  
• Remove the obstruction.  
remote control.  
and the remote sensor on the unit is  
blocked.  
• The batteries are exhausted.  
• Replace the batteries.  
Hard to listen to broadcasts  
because of noise.  
• Antennas are disconnected.  
• Reconnect the antennas correctly and  
securely.  
• The AM loop antenna is too close to  
the unit.  
• Change the position and direction of  
the AM loop antenna.  
• The FM antenna is not properly  
extended and positioned.  
• Extend the FM antenna at the best  
position.  
The disc sound is discontinuous.  
The disc is scratched or dirty.  
Clean or replace the disc. (See page 26.)  
The disc tray does not open or  
close.  
• The AC power cord is not plugged in.  
• Trays are locked.  
• Plug the AC power cord.  
• Unlock the trays. (See page 18.)  
The disc does not play.  
The disc is placed upside down.  
Place the disc with the label side up.  
Turn on the unit.  
The cassette holders cannot be  
opened.  
Power supply from the AC power cord  
has been cut off while the tape was  
running.  
Impossible to record.  
Small tabs on the back of the cassette  
are removed.  
Cover the holes with adhesive tape.  
(See page 20.)  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Amplifier section  
Output Power (IEC 268-3)  
SUBWOOFERS: 75 W per channel, min. RMS, both channels  
driven into 6 at 63 Hz with no more than  
0.9% total harmonic distortion.  
MAIN SPEAKERS: 30 W per channel, min. RMS, both channels  
driven into 6 at 1 kHz with no more than  
0.9% total harmonic distortion.  
Audio input sensitivity/Impedance  
(Measured at 1 kHz, with tape recording signal 300 mV)  
AUX:  
390 mV/50 kΩ  
Speakers/Impedance:  
SUBWOOFERS:  
6 – 16 Ω  
6 – 16 Ω  
16 – 32 Ω  
MAIN SPEAKERS:  
SURROUND SPEAKERS:  
Tuner  
FM tuning range: 87.50 MHz – 108.00 MHz  
AM tuning range: At 9 kHz intervals: 531 kHz – 1 710 kHz  
At 10 kHz intervals: 530 kHz – 1 710 kHz  
CD player  
CD capacity:  
3 CDs  
Dynamic range:  
Signal-to-noise ratio:  
Wow and flutter:  
85 dB  
90 dB  
Immeasurable  
Cassette deck  
Frequency response  
Normal (type I): 50 Hz – 14 000 Hz  
Wow and flutter:  
0.15% (WRMS)  
General  
Power requirement:  
AC 110 V / AC 127 V / AC 220 V /  
AC 230 V – AC 240 V  
(adjustable  
with the voltage selector), 50 Hz / 60 Hz  
205 W (in operation)  
Power consumption:  
23 W (on standby with Ecology Mode off)  
Less than 3.5 W (on standby with  
Ecology Mode on)  
Dimensions (approx.): 205 mm × 370 mm × 370 mm (W/H/D)  
Mass (approx.): 10.0 kg  
Supplied accessories  
See page 6.  
Design and specifications are subject to change without notice.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada,  
Australia, and U.K.)  
Instrucción sobre la línea de la red (CA) (no aplicable para Europa, EE.UU.,  
Canadá, Australia, ni el Grã-Bretanha)  
Instrução sobre a tensão da rede eléctrica (CA) (não aplicável para a Europa,  
os E.U.A., o Canadá, a Austrália e o Reino Unido)  
IMPORTANT for mains (AC) line  
BEFORE PLUGGING IN, do check that your mains (AC)  
line voltage corresponds with the position of the voltage  
selector switch provided on the outside of this equipment and,  
if different, reset the voltage selector switch, to prevent from  
damage or risk of fire/electric shock.  
IMPORTANTE para la línea de la red (CA)  
ANTES DE ENCHUFAR EL EQUIPO, compruebe si la  
tensión de la línea de la red (CA) corresponde con la posición  
del selector de tensión situado en la parte exterior del equipo,  
y si es diferente, reajuste el selector de tensión para evitar el  
riesgo de incendios/descargas eléctricas.  
IMPORTANTE para a ligação à tensão da rede (CA)  
ANTES DE LIGAR O APARELHO A UMA TOMADA DA  
REDE, verifique se a tensão da rede CA corresponde à  
posição do seletor de voltagem localizado na parte externa  
deste equipamento. Caso não corresponda, reajuste o seletor  
de voltagem a fim de evitar avarias ou riscos de incêndio e  
choque elétrico.  
VICTOR COMPANY OF JAPAN, LIMITED  
EN, SP, PR  
0203MWMMDWJEM  
2003 VICTOR COMPANY OF JAPAN, LIMITED  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Insignia Battery Charger NS PWLC593 User Manual
Intel Network Card EK KZPCM UG User Manual
John Lewis Refrigerator JLLFW1809 User Manual
JVC Camcorder Compact VHS User Manual
JVC CD Player KD DB711 User Manual
JVC Computer Drive SA K51U User Manual
Kenmore Dehumidifier 59600 User Manual
Kenmore Range 7909600 User Manual
King Canada Plumbing Product KCG 2PG User Manual
Kompernass Blender KH 498 User Manual