JVC Flat Panel Television LT Z37DX5 User Manual

ENGLISH  
LT-Z37DX5  
INSTRUCTIONS  
WIDE LCD PANEL TV  
LCT1961-001A  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Thank you for buying this JVC LCD flat television.  
To make sure you understand how to use your new TV, please read this manual thoroughly before you  
begin. (“LCD” stands for Liquid Crystal Display.)  
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS  
APPLIANCE TO RAIN OR MOISTURE.  
WARNING  
• Do not allow children to hang from the TV, place their elbows on the TV or lean against the TV.  
Doing so may cause the TV to fall over and lead to injuries.  
CAUTION  
• The TV screen may be damaged if the TV is carried as  
shown in the diagram below.  
The TV should always be carried by two people.  
Pixel defects  
LCDs use collections of fine points (“pixels”) to display images. While there is no problem with  
more than 99.99% of these pixels, please understand that a very small number of pixels may not  
light, or may light all the time.  
Distance recommendations  
Avoid improper installation and never position the unit  
where good ventilation is impossible.  
200 mm  
200 mm  
150 mm  
150 mm  
When installing this TV, distance recommendations  
must be maintained between the set and the wall, as well  
as inside a tightly enclosed area or piece of furniture.  
Keep to the minimum distance guidelines shown for  
safe operation.  
50 mm  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Failure to take the following precautions may cause damage to the television  
or remote control.  
DO NOT block the TV’s ventilation openings or holes.  
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be  
able to get out.)  
DO NOT place anything on top of the TV.  
(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)  
DO NOT allow objects or liquid into the cabinet openings.  
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)  
DO NOT place any naked flame sources, such as lighted candles, on the TV.  
DO NOT subject the TV to direct sunlight.  
The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.  
Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully.  
Never use any cleaner or detergent on it.  
If there is a fault, unplug the unit and call a service technician. Do not attempt to repair it yourself  
or remove the rear cover.  
Cleaning the screen  
The screen is coated with a special thin film to reduce reflection. If this film is damaged, uneven  
colours, discolouration, scratches, and other problems that cannot be repaired may occur. Pay  
attention to the following when handling the screen.  
• Do not use glue or adhesive tape on the screen.  
• Do not write on the screen.  
• Do not allow the screen to come in contact with any hard objects.  
• Do not allow condensation to form on the screen.  
• Do not use alcohol, thinner, benzene or other solvents on the screen.  
• Do not rub the screen hard.  
CAUTION:  
• Operate only from the power source specified (AC 110 – 240 V, 50/60 Hz) on the unit.  
• Avoid damaging the AC plug and power cord.  
• When you are not using this unit for a long period of time, it is recommended that you disconnect  
the power cord from the main outlet.  
Demonstration  
To start the demonstration:  
Press the H button to display the menu bar. Then press the yellow button.  
Select DEMO 1 (High Speed Response) or DEMO 2 (DynaPix) from the DEMO MODE menu.  
Press the 6 buttons, then press the a button.  
To quit the demonstration:  
Press the yellow button, b button, 6 p buttons or any of the number buttons.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the aerial and video cassette  
Connecting the power cord to the AC  
Putting the batteries into the remote  
control..................................................... 7  
Initial settings (Setup tour) ......................... 7  
SHARP..................................................... 24  
CINEMA SURROUND ............................. 28  
Turn the TV on from standby mode ........... 9  
Using the Menu.......................................... 9  
Remote control buttons and  
CHILD LOCK............................................ 32  
functions..............................................10  
Turn the TV on or off from standby mode ... 10  
Using the “Freeze” function...................... 14  
RETURN PLUS function and Return  
SET UP menu ......................................... 34  
VIDEO-1 SETTING/VIDEO-3 SETTING .... 38  
Operating a JVC brand DVD player......... 18  
Teletext function ....................................19  
Basic operation ........................................ 19  
Using the List Mode ................................. 19  
Hold.......................................................... 20  
Sub-page ................................................. 20  
Reveal...................................................... 20  
Size.......................................................... 20  
Index ........................................................ 21  
Cancel...................................................... 21  
Watching images from a computer .......... 40  
Table of signals for each type of  
computer............................................... 40  
Using the TV’s menu..............................22  
Basic operation ........................................ 22  
Using a Media Card ............................... 41  
Supported Media Cards and file formats ... 41  
Inserting the Media Card.......................... 42  
Using the MEDIA CARD VIEWER ........... 43  
Additional preparation .......................... 46  
Connecting external equipment ............... 46  
Using the HDMI terminal.......................... 49  
CH/CC numbers ..................................... 51  
Troubleshooting .................................... 52  
Specifications ........................................ 54  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
• When you install the TV on the wall, only use a JVC wall mounting unit (optional) which is  
designed for this TV.  
• Make sure that the TV is installed on the wall by a skilled installer.  
Installation  
Cautions for installation  
• Install the TV in a corner on a wall or on the floor so as to keep cords out of the way.  
• The TV will generate a slight amount of heat during operation. Ensure that sufficient space is  
available around the TV to allow satisfactory cooling. See “Distance recommendations” on  
page 1.  
Using the stand  
This TV comes with a table top stand already attached.  
This stand can be used to adjust the direction of the TV screen 5° up, 10° down, and 20° to the left  
or right.  
Rotate the TV to the left and right:  
While holding the bottom of the stand with one  
hand, use your other hand to hold the edge of  
the panel and slowly adjust the direction of the  
TV screen.  
Cable holder  
A cable holder which is used to keep the connection cables tidy is attached to the back of the  
stand. Gently squeeze the left and right of the cable holder and pull it to remove it from the stand.  
After putting the cables in the cable holder, attach it to the back of the stand again.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Setting up your TV  
Removing the terminal covers  
There are connection terminals behind the covers on the left and right of the rear of the TV.  
Remove these two covers before connecting an antenna or VCR.  
Remove the covers by removing the hooks.  
When replacing the covers, place the side of the covers against the TV and insert the hooks.  
• Leave the covers off if they do not fit properly. Do not force to replace the covers. Doing so  
may cause damage to the connection cables and the covers.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Setting up your TV  
Connecting the aerial and  
video cassette recorder (VCR)  
without terminal covers  
Caution  
• Turn off all the equipment including the  
TV before connecting anything.  
• Aerial cable is not supplied. Use a good  
quality 75-ohm coaxial cable.  
IN (HDMI AUDIO)  
L
(ANALOG)  
• Read the manual that came with the VCR  
before connecting.  
IN  
If not connecting a VCR (follow 1):  
Connect an aerial cable to the aerial  
socket on this TV.  
IN  
(H  
D
M
I
AU  
D
IO  
)
(A  
NALO  
G)  
IN  
If connecting a VCR:  
1 Connect the aerial cable to the  
aerial input socket on the VCR, and  
connect the VCR and TV with  
another aerial cable  
1
3
2
2 Connect the VCR’s VIDEO OUT  
(video output) terminal and the  
TV’s VIDEO terminal with a video  
cable  
To connect a VCR to the TV with an S-  
VIDEO cable:  
1
Connect the VCR’s S-VIDEO OUT (S-  
VIDEO output) terminal and TV’s S  
VIDEO terminal with an S-VIDEO cable  
A, instead of connecting with a video  
cable.  
cable will be ignored in case you connect  
a VCR to the TV with both video cable  
and S-VIDEO cable.  
3 Connect the VCR’s VIDEO OUT  
(audio L/R output) terminals and  
the TV’s AUDIO terminals with an  
audio cable  
• To connect additional external devices,  
please see “Connecting external  
equipment” on page 46.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Setting up your TV  
Connecting the power cord to  
the AC outlet  
Initial settings (Setup tour)  
When the TV is first turned on, it goes into  
the initial settings mode, and you will see the  
JVC logo. Follow the instructions on the  
screen display to make the initial settings.  
Insert the AC plug on the power cord from  
the TV into AC outlet.  
Caution  
• Operate only from the power source  
specified (AC 110 – 240 V, 50/60 Hz)  
on the unit.  
# button  
PIP/TV/DVD  
switch  
• Remove the AC plug from the outlet to  
completely disconnect the TV from the  
power supply.  
Putting the batteries into the  
remote control  
6
buttons  
Use two AA/R6 dry cell batteries.  
Insert the batteries from the - end, making  
sure the + and - polarities are correct.  
1 Make sure to set the PIP/TV/DVD  
switch on the remote control to the  
TV position  
• You cannot turn the TV on when the  
PIP/TV/DVD switch is set to the DVD  
position.  
2 Press the # button on the remote  
control  
• Follow the warnings printed on the  
batteries.  
• Battery life is about six months to one  
year, depending on how much you use the  
remote control.  
• The batteries we supply are only for  
setting up and testing your TV, please  
replace them as soon as you need to.  
• If the remote control does not work  
properly, replace the batteries.  
The TV turns on from standby mode and  
the JVC logo is displayed.  
• Check that the AC plug on the power  
cord from the TV is connected to AC  
outlet.  
Remote control  
sensor  
Power lamp  
Illumination  
lamp  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Setting up your TV  
• If the JVC logo does not appear this is  
5 Press the 6 buttons to choose a  
group. Then press the a button  
The AUTO PROGRAM function starts.  
The TV channels you receive are  
automatically stored in the programme  
numbers (PR) list.  
because your TV has already been  
turned on for the first time:  
use the “LANGUAGE”, “TELETEXT  
LANGUAGE” and “AUTO  
PROGRAM” functions to make the  
initial settings. For details, see “SET  
UP menu” on page 34.  
>> AUTO PROGRAM  
CH 28  
3 Press the a button  
14%  
The LANGUAGE menu appears.  
OK  
D0004-EN  
function, press the a button.  
6 After the TV channels have been  
registered in the programme  
numbers (PR), the EDIT menu  
appears  
4 Press the 6 buttons to choose  
ENGLISH. Then press the a  
button  
> EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH/CC  
The TELETEXT LANGUAGE menu  
appears. Set the teletext language group  
that corresponds to the language of the  
teletext programme that you want to watch.  
For details, see “TELETEXT  
CH  
CH  
CH  
CH  
CH  
CH  
CC  
CC  
CC  
21  
22  
23  
24  
25  
26  
01  
02  
03  
LANGUAGE” on page 39.  
ID  
MANUAL  
OK  
MOVE  
> TELETEXT LANGUAGE  
INSERT DELETE  
D0038-EN  
GROUP-1  
GROUP-2  
GROUP-3  
GROUP-4  
• You can proceed to edit the  
programme numbers (PR) list using  
the EDIT/MANUAL function. For  
details, see “EDIT/MANUAL” on  
page 34.  
OK  
D1003-EN  
• If a TV channel you want to view is  
not stored in the programme numbers  
(PR) list, you can register it using the  
MANUAL function. For details, see  
“EDIT/MANUAL” on page 34.  
• The AUTO PROGRAM function does  
not store a TV channel to the  
programme number PR 0 (AV).  
• If you do not need to use the EDIT/  
MANUAL function, press the a  
button to close the EDIT menu.  
Now, setting up is complete. Please  
enjoy your new JVC TV!  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV buttons and functions  
Turn the TV on from standby  
mode  
Press the A button or the CHANNEL  
p buttons to turn the TV on from  
standby mode.  
When the TV is turned on, the power lamp  
lights blue.  
To turn the TV off:  
Press the A button again.  
The power lamp goes off.  
Caution  
• The A button on the TV does not fully  
isolate the TV from the AC supply. If  
you are not going to use the TV for a  
long period, be sure to disconnect the  
AC plug from the AC socket.  
Choose a TV channel  
Press the CHANNEL p buttons to  
choose a programme number (PR) or  
a VIDEO terminal  
Press the TV/VIDEO button to choose a  
VIDEO terminal.  
4
5
6
Adjust the volume  
Press the VOLUME q buttons  
The volume level indicator appears.  
7
8
Using the Menu  
9
Use the MENU/OK button  
Refer to “Using the TV’s menu” (see  
page 22) for details of using the menu.  
Refer to the pages in parentheses for details.  
1 Remote control sensor  
2 Power lamp (page 7)  
3 Illumination lamp (page 33)  
4 TV/VIDEO button  
5 MENU/OK button (page 22)  
6 CHANNEL p buttons  
6 (page 22)  
Using the Illumination  
When the TV is turned on the Illumination  
lamp lights. To adjust the illumination  
settings, refer to “ILLUMINATION” on  
page 33.  
7 VOLUME q buttons  
5 (page 22)  
8 A (Stand by) button  
9 Headphone jack (mini jack) (page 46)  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Remote control buttons and functions  
1 Muting button  
2 Number buttons  
3 1 button  
4 c button  
5 2 button  
6 4 button  
7 7 buttons  
8 5 button  
9 6 p buttons  
0 VCR/DVD/Teletext control buttons  
- p buttons  
1
2
~
!
= d (Favourite) button  
~ # (Standby) button  
! PIP/TV/DVD switch  
@ g (Text) button  
3
4
@
#
# Colour buttons  
$ H button  
% a button  
^ b button  
5
6
$
%
& 7 q buttons  
* f (Freeze) button  
( X (Multi) button  
) c (Select) button  
7
8
^
&
Turn the TV on or off from  
standby mode  
9
*
(
Press the # (standby) button to turn  
the TV on or off  
When the TV is turned on, the power lamp  
lights blue.  
• The power can be turned on by pressing  
the 4 button, 6  
p buttons or Number buttons.  
0
-
=
)
To turn the TV on or off, set the PIP/TV/  
DVD switch on the remote control to the  
TV position and press the # button.  
If the PIP/TV/DVD switch on the remote  
control is set to the DVD position, the TV  
will not be turned on or off even if the #  
button is pressed.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Remote control buttons and functions  
• Since this TV is designed to make full use  
of the resolution of the original video  
source, the motion may appear unnatural  
when the video source is input with  
progressive-scanning component signals.  
• If this happens, change the output setting  
of the connected device to interlace-  
scanning component signal output. See  
the instructions that came with the device  
for more information.  
Choose a TV channel and  
watch images from external  
devices  
Use the number buttons:  
Enter the programme number (PR)  
of the channel using the number  
buttons.  
Example:  
• PR 6 press 6  
• PR 12 press 1 and 2  
• The PC sound is the same as the VIDEO-3  
sound.  
To return to a TV channel:  
Press the 4 button, the  
6 p buttons or the number  
buttons.  
Use the 6 p buttons:  
Press the 6 p buttons  
to choose the programme number  
(PR) you want or a VIDEO  
terminal.  
To use the programme number PR 0  
(AV):  
When the TV and VCR are connected only  
by the aerial cable, choosing the programme  
number PR 0 (AV) allows you to view  
images from the VCR. Set the VCR RF  
channel to the programme number PR 0  
(AV) manually. For details, see “EDIT/  
MANUAL” on page 34.  
Use the 4 button:  
Press the 4 button to  
choose a VIDEO terminal.  
or  
Programme  
numbers  
PR 1 – PR 99  
or  
(HDMI)  
4
4
• The leading character is changed from V  
to S (eg V1 is changed to S1) when  
VIDEO-1 or VIDEO-2 is connected to the  
S terminal.  
• If you do not have a clear picture or no  
colour appears, follow the operation  
procedure “COLOUR SYSTEM” on  
page 26.  
• If you cannot hear the normal sound even  
if the picture of the TV channel appears  
normally. Follow the description “EDIT/  
MANUAL” on page 34 to use the  
MANUAL function to change the  
SYSTEM setting.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Remote control buttons and functions  
PR LIST:  
Adjust the volume  
The programme number (PR) and VIDEO  
terminal list is displayed.  
Press the 7 q buttons to  
adjust the volume.  
The volume level indicator appears and the  
volume changes as you press the 7  
q buttons.  
Pressing the a button after choosing the  
programme number (PR) or VIDEO terminal  
• For programme numbers (PR) for which  
the CHANNEL GUARD function is set,  
the n (CHANNEL GUARD) mark is  
displayed. For details see “CHANNEL  
GUARD” on page 30.  
Muting the sound  
Press the (muting) button to  
l
turn off the sound.  
Pressing the (muting) button again  
l
• The VIDEO terminals are registered after  
the programme number PR 99.  
restores the previous volume level.  
• For programme numbers (PR) which is  
registered as a favourite channel, the d  
(favourite) mark is displayed. For details  
see “Favourite channel function” on  
page 17.  
Display function  
You can see the channel number of the  
programme you are watching or the PR  
LIST.  
From the PR LIST, you can choose a channel  
or VIDEO terminal.  
Press the  
the information you want to see.  
button to display  
5
Pressing the  
button changes the  
5
display as follows:  
PR LIST  
PR  
ID  
Channel number display  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
No indication  
OK  
-10  
+10  
D0011-EN  
Channel number display:  
The channel number and channel name  
(when the channel name is registered) of the  
programme you are watching or the VIDEO  
terminal number is displayed.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Remote control buttons and functions  
16:9 ZOOM:  
This zooms up the wide picture (16:9 aspect  
ratio) to the full screen.  
ZOOM function  
You can change the screen size according to  
the picture aspect ratio. Choose the optimum  
one from the following ZOOM modes.  
• The ZOOM mode is fixed at FULL when  
you are using the TV as a PC screen or  
watching a 1080i or 720p picture signal.  
16:9 ZOOM SUBTITLE:  
This zooms up the wide picture (16:9 aspect  
ratio) with subtitles to the full screen.  
AUTO:  
When a WSS (Wide Screen Signalling)  
signal, which shows the aspect ratio of the  
picture, is included in the broadcast signal or  
the signal from an external device, the TV  
automatically changes the ZOOM mode to  
16:9 ZOOM mode or FULL mode according  
to the WSS signal.  
FULL:  
This uniformly stretches the left and right  
sides of a normal picture (4:3 aspect ratio) to  
fill the wide TV screen.  
If a WSS signal is not included, the picture is  
displayed according to the ZOOM mode set  
with the 4:3 AUTO ASPECT function.  
• For details of the 4:3 AUTO ASPECT  
function, see “4:3 AUTO ASPECT” on  
page 27.  
• When the AUTO (WSS) mode does not  
function correctly due to poor WSS signal  
quality or when you want to change the  
ZOOM mode, press the c button  
and change to another ZOOM mode.  
• For 16:9 aspect ratio pictures that have  
been squeezed into a normal picture (4:3  
aspect ratio), use the FULL mode to  
restore the picture to its original shape.  
Choose the ZOOM mode  
1 Press the c button to display  
the ZOOM menu  
ZOOM  
REGULAR:  
AUTO  
Use to view a normal picture (4:3 aspect  
ratio) as this is its original shape.  
REGULAR  
PANORAMIC  
14:9 ZOOM  
16:9 ZOOM  
16:9 ZOOM SUBTITLE  
FULL  
OK  
PANORAMIC:  
This stretches the left and right sides of a  
normal picture (4:3 aspect ratio) to fill the  
screen, without making the picture appear  
unnatural.  
D0009-EN  
2 Press the 6 buttons to choose a  
ZOOM mode. Then press the a  
button  
The picture expands and the chosen  
ZOOM mode is displayed in about 5  
seconds.  
• The ZOOM mode may be  
automatically changed by the control  
signal from an external device. When  
you want to return to the previous  
ZOOM mode, choose the ZOOM  
mode again.  
• The top and bottom of the picture are  
slightly cut off.  
14:9 ZOOM:  
This zooms up the wide picture (14:9 aspect  
ratio) to the upper and lower limits of the  
screen.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Remote control buttons and functions  
• When you set the CINEMA SURROUND  
function to HIGH mode, there may be  
slight volume distortion. If that occurs,  
please switch to LOW mode. The effect  
of CINEMA SURROUND functions will  
be less noticeable, but the volume  
Adjusting the visible area of the  
picture  
If subtitles or the top (or bottom) of the  
picture are cut off, you can adjust the visible  
area of the picture manually.  
1 Press the c button  
The ZOOM menu appears.  
MONO:  
Select the MONO mode, when you listen to  
the mono sound.  
You can enjoy the sound for a wider  
audience similar to stereo sound.  
2 Press the a button to display the  
ZOOM mode indicator  
The indicator appears.  
16 : 9 ZOOM  
OFF:  
D0010-EN  
The CINEMA SURROUND function  
switches off.  
3 While it is displayed, press the 6  
buttons to change the position of  
the picture  
• You can choose the CINEMA  
SURROUND mode with the “SOUND  
menu” (see page 28).  
• You cannot adjust the visible area in  
REGULAR or FULL mode.  
The visible area adjustment is saved even  
after the TV channel is changed.  
However, it is cancelled if the following  
operations are performed.  
Using the “Freeze” function  
You can view the current programme as a  
still picture.  
• The power is turned off/on  
• The ZOOM mode is changed  
• The X (Multi) button, f (Freeze)  
button, or g (Text) button is pressed  
• The TV is switched between TV mode  
and VIDEO mode  
1 Set the PIP/TV/DVD switch to the  
PIP position  
When using the “Freeze” function, set the  
PIP/TV/DVD switch to the PIP position.  
2 Press the f button  
The still picture of the current picture will  
appear.  
CINEMA SURROUND function  
You can enjoy sounds with a wider  
ambience.  
current  
programme  
still picture  
• This function does not work for the sound  
from headphones.  
D0056  
Press the 2 button to select  
one of CINEMA SURROUND modes  
HIGH/LOW:  
When you listen to stereo sound, please  
select HIGH or LOW mode.  
You can enjoy sound similar to the  
experience at the theatre.  
When you combine the functions of A.H.B.  
and BBE, you can enjoy more powerful  
sound.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Remote control buttons and functions  
To cancel the “Freeze” function:  
Press the f button, the 6  
p buttons or the number buttons.  
12-pictures multi:  
Still  
pictures  
• The “Freeze” function does not work  
while a sub-picture is displayed.  
• The still picture cannot be output from  
the TV.  
• The “Freeze” function does not work  
for picture of PC signals.  
Moving  
picture  
D0058  
• When set to 2-pictures multi, you can  
view a TV picture and a picture from  
an external device. You cannot view a  
TV picture on more than one screen at  
the same time.  
• When 12-pictures multi is set, pictures  
from external devices are not displayed.  
• When watching a picture from the  
HDMI signal, 12-pictures multi can  
not be displayed.  
• When set to 2-pictures multi, the main-  
picture can be changed by pressing the  
6 p buttons. The sub-  
picture screen can be changed by  
pressing the 6 buttons.  
When set to 12-pictures multi and  
there are more than 12 pictures, the  
next or previous 12 screens can be  
displayed by pressing the  
Using the “Multi-picture”  
function  
1 Set the PIP/TV/DVD switch to the  
PIP position  
When using the “Multi-picture” function,  
set the PIP/TV/DVD switch to the PIP  
position.  
2 Press the X button  
The “Multi-picture” menu appears.  
1
2
12  
D0101  
6 p buttons.  
3 Press the 5 buttons to choose  
the number of screens and then  
press the a button  
• When set to 2-pictures multi, the main-  
picture sound from the TV speaker can  
be changed to the sub-picture sound by  
pressing the c button when the PIP/  
TV/DVD switch is set to the PIP  
position. (The speaker mark moves  
from the main-picture to the sub-  
picture.)  
Choose to return to one screen.  
1
D0102  
Choose to change to 2-pictures multi.  
2
D0103  
The sound changes to the main-picture  
sound if the c button is pressed again.  
When the headphones are connected,  
you can listen to the sound from the  
side at which the headphones mark is  
displayed. No sound comes from the  
TV speaker.  
• When set to 2-pictures multi, picture  
from HDMI can not be displayed on  
the Sub-picture.  
• The pictures from VIDEO-1 (or  
VIDEO-3) cannot be displayed in the  
sub-picture when the VIDEO-1  
SETTING (or VIDEO-3 SETTING) is  
set to COMPONENT (see page 38).  
Choose to change to 12-pictures multi.  
12  
D0104  
2-pictures multi:  
Main-  
picture  
Sub-  
picture  
D0056  
With 1080i and 720p signals, the screen is  
split into two as shown below.  
Main-  
picture  
Sub-  
picture  
D1056  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Remote control buttons and functions  
• The “Multi-picture” function does not  
work for a PC signals.  
To cancel a TV channel registered as  
the “Return Channel”:  
While viewing any TV channel, press the  
1 button and hold for more than 3  
seconds continuously. “RETURN PLUS  
CANCELED!” is displayed and the  
registration is cancelled.  
• When you turn off the TV, the registration  
for the “Return Channel” is cancelled.  
• If you want to view the “Return Channel”  
and another TV channel alternately, first  
choose a channel other than the “Return  
Channel”. And then press the  
• When set to 12-pictures multi, press  
the 7 buttons to choose the  
screen you want to view and the press  
the a button to display that picture  
on the whole screen.  
• The BLUE BACK function does not  
work when the “Multi-picture”  
function is being used.  
• The ZOOM function does not work  
when the “Multi-picture” function is  
being used.  
1 button to change the channel  
to the “Return Channel” In this way, you  
can view two channels alternately by  
pressing the 1 button.  
To return the “Multi-picture” to one  
screen:  
Press the X button, press the 5  
buttons to choose one screen, and then  
press the a button.  
Return function  
• Pressing the 4 button will  
also return the display to one screen.  
The TV temporarily memorises the TV  
channel that was chosen right before the  
current TV channel as the “Last Channel”.  
By pressing the 1 button, you can  
alternately view the current TV channel and  
the “Last Channel”.  
RETURN PLUS function and  
Return function  
If you want to view two channels alternately  
by using the Return function, first choose one  
TV channel and then choose the other TV  
channel with the number buttons. If you  
choose the TV channel without using the  
number buttons, there are cases where a  
channel other than the one you first chose is  
registered as the “Last Channel”.  
The 1 button has two functions;  
the RETURN PLUS function and the Return  
function. If a channel has been registered as  
the “Return Channel”, the RETURN PLUS  
function operates. If there is no setting for the  
“Return Channel”, the Return function  
operates.  
RETURN PLUS  
By registering a channel you frequently view  
as the “Return Channel”, you can select that  
channel at any time simply by pressing the  
1 button.  
To register a TV channel as the  
“Return Channel”:  
Choose the Programme number to which the  
channel you want to register has been set,  
and press the 1 button and hold  
for more than 3 seconds continuously.  
“RETURN PLUS PROGRAMMED!” is  
displayed and the registration is completed.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Remote control buttons and functions  
Calling the favourite channel  
Favourite channel function  
1 In the normal screen, press the d  
(favourite) button  
You can register your favourite TV channels  
(PR 1 – PR 99) in the number buttons 1 to 4.  
After registering, the channel can be called  
by pressing the d (favourite) button and a  
number button 1 to 4.  
Then “FAVOURITE1-4?” appears.  
2 Press one of the number buttons 1  
to 4  
Favourite channel registration  
The called favourite channel appears on  
the screen.  
• If a number button in which no  
channel is registered is pressed, “NO  
MEMORY” appears on the screen.  
1 In the normal screen, choose a TV  
channel (PR 1 – PR 99) that you  
want to register  
For details, refer to “Choose a TV channel  
and watch images from external devices”  
on page 11.  
Setting the picture effect  
When a favourite channel has been chosen  
with the d (favourite) button and number  
buttons 1 to 4, picture effect settings can be  
memorised for each favourite channel by  
setting the picture effects in the PICTURE  
menu (see page 24).  
2 Press and hold the d (favourite)  
button for three seconds or more  
Then “SET 1-4?” appears on the screen.  
The following items in the PICTURE menu  
(see page 24) are memorised.  
PICTURE MODE  
BACK LIGHT  
CONTRAST  
BRIGHT  
SHARP  
COLOUR  
TINT  
WHITE BALANCE  
DIGITAL VNR  
COLOUR SYSTEM  
The last setting made for each item is  
memorised.  
3 Press one of the number buttons 1  
to 4  
The current channel is registered in the  
pressed number button.  
After “PROGRAMMED!” appears on the  
screen, the favourite channel icon appears  
at the top-right of the screen.  
• If the channel you are trying to register  
is already registered in one of the other  
number buttons 1 to 4, “NOT  
AVAILABLE” appears on the screen.  
• Channels locked with the CHANNEL  
GUARD function cannot be registered.  
• If AUTO PROGRAM is performed,  
the registered favourite channels are  
reset.  
• When you want to delete a favourite  
channel, delete the set channel and set  
contents with FAVOURITE SETTING  
(see page 32) in the FEATURES menu.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Remote control buttons and functions  
Operating a JVC brand DVD  
player  
These buttons will operate a JVC brand DVD  
player. Pressing a button that looks the same  
as the device’s original remote control button  
has the same effect as the original remote  
control.  
1 Set the PIP/TV/DVD switch to the  
DVD position  
When you are operating the DVD player,  
set the switch to the DVD position.  
• You can turn the DVD player on or off  
with the # (standby) button.  
• You can also press the H or  
T button and display the  
DVD disc menu screen, and then  
operate by pressing the 7  
buttons.  
2 Press the DVD control button to  
control your DVD player  
• If your DVD player is not made by  
JVC, these buttons will not work.  
• Even if your device is made by JVC,  
some of these buttons may not work,  
depending on the device you are using.  
You cannot turn the TV on or off when the  
PIP/TV/DVD switch is set to the DVD  
position.  
When you turn the TV on or off, set the  
PIP/TV/DVD switch to the TV position.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Teletext function  
4 Choose a teletext page by pressing  
the 6 p buttons,  
number buttons or colour buttons  
To return to the TV mode:  
Press the 4 button, b  
button, or g (Text) button.  
PIP/TV/  
DVD  
• If you have trouble receiving teletext  
broadcasts, consult your local dealer or  
the teletext station.  
• The ZOOM function will not work in  
the TV and text mode or Text mode.  
• You cannot operate menus when  
viewing a teletext programme.  
• If characters on a teletext programme  
do not appear properly, change the  
TELETEXT LANGUAGE setting. For  
details, see “TELETEXT  
Basic operation  
LANGUAGE” on page 39.  
1 Choose a TV channel with a teletext  
broadcast  
2 Set the PIP/TV/DVD switch to the  
TV position  
Using the List Mode  
You can store the numbers of your favourite  
teletext pages in memory and call them up  
quickly using the colour buttons.  
To store the page numbers:  
3 Press g (Text) button to display  
the teletext  
1 Press B button to go into the  
List mode  
Pressing g (Text) button changes the  
mode as follows:  
The page numbers you have stored are  
displayed at the bottom of the screen.  
TEXT  
TEXT  
---  
---  
TV mode  
TV and text mode  
TEXT  
TEXT  
---  
---  
D1043  
Text mode  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Teletext function  
2 Press a colour button to choose a  
position. Then press the number  
buttons to enter the page number  
Sub-page  
Some teletext pages include sub-pages that  
are automatically displayed.  
1 Choose a teletext page that  
includes sub-pages  
Sub-page numbers that can be viewed are  
automatically displayed at the top of the  
screen.  
3 Press and hold down the A (Store)  
button  
2 Press the 5 buttons to choose a  
sub-page number  
The four page numbers blink white to  
show that they are stored in memory.  
Reveal  
To call up a stored page:  
Some teletext pages include hidden text  
(such as answers to a quiz).  
You can display the hidden text.  
1 Press the B button to enter the  
List mode  
Each time you press the E (Reveal)  
button, text is hidden or revealed  
2 Press a colour button having a  
stored page  
To exit the List mode:  
Press the B button again.  
Size  
Hold  
You can double the height of the teletext  
display.  
You can hold a teletext page on the screen for  
as long as you want, even while several other  
teletext pages are being received.  
Press the F (Size) button  
Press the C (Hold) button  
Hold indication  
To cancel the Hold function:  
Press C (Hold) button again.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Teletext function  
Index  
You can return to the index page instantly.  
Press the G (Index) button  
Returns to page 100 or a previously specified  
page.  
Cancel  
You can search for a teletext page while  
watching TV.  
1 Press the number button to enter a  
page number, or press a colour  
button  
The TV searches for a teletext page.  
2 Press H (Cancel) button  
The TV programme appears. When the  
TV finds the teletext page, its page  
number appears in the upper left of the  
screen.  
3 Press H (Cancel) button to return  
to a teletext page when the page  
number is on the screen  
• The TV mode cannot be resumed by  
pressing the H (Cancel) button. To  
return to the TV mode press  
4 or b button.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Using the TV’s menu  
This TV has a number of functions you can  
operate using menus. To use all your TV’s  
functions, you need to understand the basic  
menu operating techniques fully.  
Types of menu  
PICTURE menu  
Choose to set the screen  
settings.  
D0106  
D0107  
D0108  
Buttons used to operate the menus  
SOUND menu  
Choose to set the sound settings.  
FEATURES menu  
Choose to set the sleep timer  
and child lock settings.  
SET UP menu  
Choose to edit the channels or  
set the display language  
settings.  
D0109  
• The menu will disappear after about  
one minute if no operation is  
performed.  
Basic operation  
1 Press the H button to display  
The menu guide area can be made to appear  
and disappear for some menus.  
the menu bar  
PICTURE  
While the menu is displayed, press the  
5 button to change between the  
guide area being displayed and not displayed.  
D0105-EN  
2 Press the 5 buttons to choose  
the menu you want to use and then  
press the a button  
>> 4:3 AUTO ASPECT  
PANORAMIC  
REGULAR  
14:9 ZOOM  
PICTURE  
OK  
D1105-EN  
Chosen  
menu  
Chosen  
menu name  
D0017-EN  
Guide area  
3 Press the 6 buttons to choose  
the item to be set, press the 5  
buttons to set the item, and then  
press the a button  
>> 4:3 AUTO ASPECT  
PANORAMIC  
REGULAR  
14:9 ZOOM  
If there are sub-menus, use the 7  
buttons to operate them.  
D1017-EN  
• Press the b button to return to  
the previous menu.  
• Press the 4 or H  
button to exit from the menu.  
• The guide area for some menus will still  
be displayed even if the 5  
button is pressed. This is not a fault.  
• Some menu items may not be operated  
or set depending on the TV status, input  
signal or other menu item settings.  
Menu items that cannot be operated or  
set are displayed in grey in the menu  
and cannot be chosen.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Using the TV’s menu  
Operation with the buttons on the TV  
You can also operate the menus using the  
buttons on the front panel of the TV.  
TV/VIDEO button  
MENU/OK button  
6 buttons  
5 buttons  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PICTURE menu  
PICTURE  
BACK LIGHT  
STANDARD  
PICTURE MODE  
BACK LIGHT  
CONTRAST  
BRIGHT  
SHARP  
COLOUR  
TINT  
WHITE BALANCE  
FEATURES  
You can adjust the back light.  
2 :darker  
3 : brighter  
COOL  
RESET  
CONTRAST  
OK  
D0014-EN  
You can adjust the picture contrast.  
2 :lower  
3 : higher  
• While the PICTURE menu is displayed,  
pressing the blue button will set the  
BACK LIGHT, CONTRAST, BRIGHT,  
SHARP, COLOUR, TINT settings to  
their default settings.  
• When watching the picture from VIDEO-  
1 to VIDEO-4 (HDMI) or the PC, picture  
effect settings can be memorised for each  
external input by setting the picture  
effects in the PICTURE menu.  
The following items in the PICTURE  
menu are memorised.  
BRIGHT  
You can adjust the picture brightness.  
2 :darker  
3 : brighter  
SHARP  
You can adjust the picture sharpness.  
2 :softer  
3 : sharper  
PICTURE MODE  
BACK LIGHT  
CONTRAST  
BRIGHT  
COLOUR  
You can adjust the picture colour.  
2 :lighter  
3 : deeper  
SHARP  
COLOUR  
TINT  
WHITE BALANCE  
DIGITAL VNR  
COLOUR SYSTEM  
TINT  
You can adjust the picture tint.  
2 :reddish  
3 : greenish  
The last setting made for each item is  
memorised.  
• You can change the TINT setting (picture  
hue) when the colour system is NTSC  
3.58, or NTSC 4.43.  
PICTURE MODE  
You can choose one of three PICTURE  
MODEs to adjust the picture settings  
automatically.  
WHITE BALANCE  
You can select one of three WHITE  
BALANCE modes (three tones of white) to  
adjust the white balance of the picture. Since  
white is the colour which is used as a  
reference for all the other colours, changing  
the WHITE BALANCE mode affects the  
appearance of all the other colours on the  
screen.  
BRIGHT:  
Heightens contrast and sharpness.  
STANDARD:  
Standardises picture adjustment.  
SOFT:  
Softens contrast and sharpness.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
PICTURE menu  
COOL:  
MIN:  
A bluish white. Using this mode when  
watching bright pictures allows you to enjoy  
a more vivid and bright picture.  
The level of the DIGITAL VNR effect is set  
to the minimum. If you set the DIGITAL  
VNR function to AUTO(LOW) but feel that  
the sharpness of the original picture has not  
been reproduced fully, change the setting  
from AUTO(LOW) to MIN.  
• The MIN setting is not suitable for low-  
quality pictures which contain a lot of  
noise.  
MID:  
The normal white colour.  
WARM:  
A reddish white. Using this mode when  
watching films allows you to enjoy colours  
that are characteristic of films.  
MAX:  
The level of the DIGITAL VNR effect is set  
to the maximum. If you set the DIGITAL  
VNR function to AUTO(HIGH) but still  
notice some noise, change the setting from  
AUTO(HIGH) to MAX.  
• The MAX setting is not suitable for high-  
quality pictures which contain very little  
noise.  
FEATURES  
Choose FEATURES and press the a or 3  
button to display the sub-menu.  
> FEATURES  
DIGITAL VNR  
Super DigiPure  
PULL DOWN  
COLOUR MANAGEMENT  
PICTURE MANAGEMENT  
COLOUR SYSTEM  
4:3 AUTO ASPECT  
AUTO(LOW)  
AUTO  
AUTO  
ON  
ON  
Super DigiPure  
The Super DigiPure function uses the latest  
in digital technology to give you a natural-  
looking picture. The Super DigiPure function  
includes the following two functions.  
OK  
D1015-EN  
DigiPure function:  
DIGITAL VNR  
This function helps to create a natural-  
looking picture by eliminating unnecessary  
edges from high-contrast and crisp images.  
For images with low-contrast, edges are  
added to produce a sharper, more detailed  
picture.  
You can choose from the three DigiPure  
function settings of AUTO, MIN and MAX.  
• If you set the DigiPure effect too high on  
a low-quality picture that contains a lot of  
noise, this may actually make the noise  
worse. We recommend you use the  
AUTO setting if you can.  
The DIGITAL VNR function cuts down the  
amount of ‘noise’ (‘snow’ or interference) in  
the original picture.  
You can choose from the three DIGITAL  
VNR function settings of AUTO, MIN and  
MAX.  
AUTO(LOW)/AUTO(HIGH):  
The TV will automatically adjust the level of  
the DIGITAL VNR effect to match the  
amount of noise in the picture, giving you the  
best possible picture.  
• If you set the DIGITAL VNR effect too  
high it can make the picture less sharp. It is  
recommended you use the AUTO(LOW)  
setting if you can. If you set the DIGITAL  
VNR function to AUTO(LOW) but still  
notice some noise, change the setting from  
AUTO(LOW) to AUTO(HIGH).  
Picture motion compensation  
function:  
This function displays fast-moving pictures  
(for example, the players or ball in a football  
game) more smoothly and naturally on the  
screen.  
• The effect level of the picture motion  
compensation function cannot be  
changed. The effect level is the same no  
matter which of the AUTO, MIN or MAX  
settings is used.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PICTURE menu  
AUTO:  
COLOUR MANAGEMENT  
This TV supports the COLOUR  
MANAGEMENT function to ensure dull  
colours are compensated to produce natural  
hues.  
The TV will automatically adjust the level of  
the DigiPure effect to match the amount of  
noise in the picture, giving the best possible  
picture.  
The COLOUR MANAGEMENT function is  
on by default.  
ON:  
COLOUR MANAGEMENT function is  
turned on.  
OFF:  
COLOUR MANAGEMENT function is  
turned off.  
MIN:  
The level of DigiPure effect is set to the  
minimum. When you set the Super DigiPure  
function to AUTO and notice some noise,  
change the setting from AUTO to MIN.  
• The MIN setting is not suitable for high-  
quality pictures which contain very little  
noise.  
MAX:  
• Set this function to ON under normal  
conditions.  
The level of DigiPure effect is set to the  
maximum. If you set the Super DigiPure  
function to AUTO but feel that the original  
picture quality has not been reproduced fully,  
change the setting from AUTO to MAX.  
• The MAX setting is not suitable for low-  
quality pictures which contain a lot of  
noise.  
PICTURE MANAGEMENT  
The PICTURE MANAGEMENT function  
makes it easier to see the dark areas when a  
picture has many dark areas, and makes it  
easier to see the bright areas when a picture  
has many bright areas.  
OFF:  
The Super DigiPure function is turned off.  
Normally use with this function on.  
ON:  
PULL DOWN  
PICTURE MANAGEMENT function is  
turned on.  
The PULL DOWN function displays a  
cinema film picture more smoothly and  
naturally on the screen.  
OFF:  
PICTURE MANAGEMENT function is  
turned off.  
AUTO:  
The television automatically recognises the  
type of signal and turns the function on and  
off.  
COLOUR SYSTEM  
The colour system is chosen automatically.  
However, if the picture is not clear or no  
colour appears, choose the colour system  
manually.  
ON:  
This function is turned on.  
OFF:  
This function is turned off.  
1 Choose COLOUR SYSTEM. Then  
press the a or 3 button  
The sub-menu of the COLOUR SYSTEM  
function appears.  
>> COLOUR SYSTEM  
MAIN  
SUB  
PAL  
AUTO  
OK  
D0016-EN  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PICTURE menu  
For colour system in your country or  
region, refer to the table below:  
2 Press the 5 buttons to choose  
MAIN or SUB  
MAIN:  
You can change the colour system of the  
main-picture.  
SUB:  
You can change the colour system of the  
sub-picture.  
• Choose MAIN when a sub-picture is  
not displayed.  
Area  
Country or Region  
System  
Bahrain, Kuwait, Oman,  
Qatar, United Arab Emirates,  
Yemen, etc.  
Indonesia, Malaysia,  
Singapore, Thailand, India,  
etc.  
PAL  
Asia,  
Middle  
East  
China, Vietnam, etc.  
Hong Kong, etc.  
PAL  
PAL  
Islamic Republic of Iran,  
Lebanon, Saudi Arabia, etc.  
SECAM  
3 Press the 6 buttons to choose  
the appropriate colour system.  
Then press the a button  
Philippines, Taiwan,  
Myanmar, etc.  
NTSC  
Russia, etc.  
SECAM  
PAL:  
PAL system  
SECAM:  
SECAM system  
Czech Republic, Poland, etc. PAL  
Europe  
Germany, Holland, Belgium,  
etc.  
UK, etc.  
PAL  
PAL  
Oceania Australia, New Zealand, etc. PAL  
Republic of South Africa, etc. PAL  
NTSC 3.58:  
NTSC 3.58 MHz system  
Africa Nigeria, etc.  
Egypt, Morocco, etc.  
PAL  
SECAM  
NTSC 4.43:  
NTSC 4.43 MHz system  
AUTO:  
4:3 AUTO ASPECT  
This function detects a colour system  
from the input signal.  
You can choose one of three ZOOM modes,  
REGULAR, PANORAMIC or 14:9 ZOOM,  
as the ZOOM mode for the normal picture  
(4:3 aspect ratio).  
• The AUTO function may not function  
properly if you have poor signal quality.  
If the picture is abnormal in the AUTO  
function, choose another colour system  
manually.  
1 Choose 4:3 AUTO ASPECT then  
press the a button  
>> 4:3 AUTO ASPECT  
PANORAMIC  
REGULAR  
14:9 ZOOM  
OK  
D0017-EN  
2 Press the 6 buttons to choose a  
ZOOM mode  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
SOUND menu  
SOUND  
TREBLE  
STEREO/  
BASS  
TREBLE  
BALANCE  
CINEMA SURROUND  
You can adjust the high tone of the sound.  
2 :weaker  
3 : strong  
OFF  
OFF  
OFF  
A.H.B.  
BBE  
BALANCE  
OK  
You can adjust the volume balance between  
the left and right speaker.  
3 : turn the right speaker’s volume level up.  
D0019-EN  
• When the headphones are connected, only  
“STEREO / I • II” can be used.  
STEREO / I • II  
When you are viewing a bilingual broadcast  
programme, you can choose the sound from  
Bilingual I (Sub I) or Bilingual II (Sub II).  
effect by using the CINEMA SURROUND  
function.  
• You can choose a CINEMA  
SURROUND mode from HIGH, LOW,  
MONO and OFF modes. For details, see  
“CINEMA SURROUND function” on  
page 14.  
• You can also operate the CINEMA  
SURROUND function with the  
2 button. For details, see  
“CINEMA SURROUND function” on  
page 14.  
s: Stereo sound  
v : mono sound  
t : Bilingual I (sub I)  
u : Bilingual II (sub II)  
MONO:  
Cancels the Multi Sound function and the  
sound becomes monaural.  
• If stereo sound or bilingual sound is hard  
to hear, please select MONO so that you  
can hear the broadcast more clearly.  
• The sound mode you can choose differs  
depending on the TV programme.  
• This function does not work in the  
VIDEO modes.  
A.H.B. (Active Hyper Bass)  
Used when you want to emphasise the bass  
sound.  
ON:  
This function is turned on.  
OFF:  
This function is turned off.  
BASS  
You can adjust the low tone of the sound.  
2 :weaker  
3 : strong  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
SOUND menu  
BBE  
BBE function restores clarity and presence  
for better speech intelligibility and musical  
realism.  
ON:  
This function is turned on.  
OFF:  
This function is turned off.  
• Manufactured under license from BBE  
Sound, Inc. Licensed by BBE Sound, Inc.  
under USP4638258, 5510752 and  
5736897. BBE and BBE symbol are  
registered trademarks of BBE Sound, Inc.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
FEATURES menu  
To cancel the SLEEP TIMER  
function:  
Press the 2 button to set the period of  
time to “OFF”.  
FEATURES  
SLEEP TIMER  
CHANNEL GUARD  
APPEARANCE  
BLUE BACK  
CHILD LOCK  
TYPE A  
ON  
OFF  
AUTO SHUTOFF  
FAVOURITE SETTING  
ILLUMINATION  
OFF  
OFF  
CHANNEL GUARD  
MEDIA CARD VIEWER  
When there is a TV channel you do not want  
your children to watch, you can use the  
CHANNEL GUARD function to lock out the  
TV channel. Even when a child chooses a  
programme number (PR) for a locked TV  
channel the screen will change to blue and  
display n (CHANNEL GUARD) so the TV  
channel cannot be viewed. Unless you enter a  
pre-set ID number by a special operation, the  
lock cannot be released and the child cannot  
view the TV channel.  
OK  
D0023-EN  
SLEEP TIMER  
You can set the TV to automatically turn off  
after a set period of time.  
1 Choose SLEEP TIMER. Then press  
the a or 3 button  
A Sub-menu of the SLEEP TIMER  
function appears.  
To set the CHANNEL GUARD  
function  
> SLEEP TIMER  
1 Choose CHANNEL GUARD, then  
press the 0 button  
0
120  
OFF  
“SET ID NO.” (ID number setting screen)  
appears.  
OK  
>> SET ID NO.  
D0024-EN  
0040  
2 Press the 5 buttons to set the  
period of time.  
OK  
Then press the a button  
You can set the period of time for up to  
120 minutes (2 hours) in 10 minute steps.  
• One minute before the SLEEP TIMER  
function turns off the TV, “GOOD  
NIGHT!” appears.  
• The SLEEP TIMER function cannot  
be used to turn off the TV’s main  
power.  
D0025-EN  
2 Set the ID number to your liking  
1 Press the 6 buttons to choose  
a number.  
2 Press the 5 buttons to move  
the cursor.  
• When the SLEEP TIMER function is  
on, you can display the sub-menu of  
the SLEEP TIMER function again to  
confirm or change the remaining  
period of time of the SLEEP TIMER  
function. Press the a button to leave  
the menu after confirming or changing  
the remaining time.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
FEATURES menu  
button to  
display “ID NO.” (ID No. input  
screen)  
3 Press the a button  
The Sub-menu of CHANNEL GUARD  
appears.  
2 Press the  
5
> CHANNEL GUARD  
5
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH/CC  
ID NO.  
:
CH  
CH  
CH  
CH  
CH  
CH  
CC  
CC  
CC  
21  
22  
23  
24  
25  
26  
01  
02  
03  
D0028-EN  
3 Press the number buttons to enter  
the ID number  
The lock is temporarily released so you  
can view the TV channel.  
GUARD  
OK  
If you have forgotten the ID  
number:  
D1026-EN  
Perform step 1 of “To set the CHANNEL  
GUARD function”. After confirming the  
ID number, press the 4 button  
to exit the menu.  
4 Press the 6 buttons to choose a  
TV channel  
Every time you press the 6 buttons, the  
Programme number (PR) changes, and the  
picture of the TV channel registered in the  
Programme number (PR) is displayed on  
the screen.  
• Even if you reset the lock temporarily,  
it does not mean that the CHANNEL  
GUARD function set for the TV  
channel is cancelled. The next time  
anyone tries to view the TV channel, it  
will be locked again.  
5 Press the blue button and set the  
CHANNEL GUARD function.  
Then press the a button  
• When you want to cancel the  
n (CHANNEL GUARD) appears and the  
TV channel is locked.  
CHANNEL GUARD function, you  
must perform the operation “To set the  
CHANNEL GUARD function” again.  
• To stop it being easy to choose the  
programme number (PR) of a locked  
TV channel, the programme number  
(PR) has been set so that it cannot be  
chosen with the 6 buttons or the  
buttons of the TV.  
To reset the CHANNEL GUARD  
function:  
Press the blue button again.  
n (CHANNEL GUARD) disappears.  
To disable easy resetting of the  
CHANNEL GUARD function, the menu  
disappears if you choose the CHANNEL  
GUARD function and press the a  
button.  
• To stop it being easy to reset the lock,  
“ID NO.” (ID No. input screen) is set  
so that it cannot appear unless you  
press the  
button.  
5
To view a locked TV channel  
1 Choose a programme number (PR)  
of a locked TV channel with the  
number buttons or PR LIST  
The screen changes to blue and the n  
(CHANNEL GUARD) appears. You  
cannot view the TV channel.  
5
D0027  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES menu  
APPEARANCE  
AUTO SHUTOFF  
Press the 5 button and choose the format  
in which the channel number is displayed  
from the four types: TYPE A, TYPE B,  
TYPE C, and TYPE D.  
You can set the power to turn off if no signal  
is received and no operation is performed for  
about 15 minutes or longer after the end of a  
broadcast.  
ON:  
• Set to TYPE D when shipped from  
factory. TYPE D sets all screens to  
semitransparent.  
The menu screens are not semitransparent  
when set to a type other than TYPE D.  
This function is turned on.  
OFF:  
This function is turned off.  
• The AUTO SHUTOFF function does not  
turn off the TV’s main power.  
• The AUTO SHUTOFF function does not  
work for the VIDEO mode or a picture  
from a PC signal.  
BLUE BACK  
You can set the TV to automatically change  
to a blue screen and mute the sound if the  
signal is weak or absent, or when there is no  
input from an external device.  
FAVOURITE SETTING  
Chose when deleting the favourite channels  
registered in the buttons 1 to 4.  
ON:  
This function is turned on.  
1 Choose FAVOURITE SETTING,  
then press the a or 3 button  
The FAVOURITE SETTING menu  
appears.  
OFF:  
This function is turned off.  
CHILD LOCK  
FAVOURITE SETTING  
You can disable the front control buttons of  
the TV. When this function is set to ON, the  
TV can be operated only by using the remote  
control.  
Use this function to prevent children from  
operating the TV at their own discretion  
(without parent consent).  
1
2
3
4
PR 01  
PR 02  
PR 03  
PR 04  
RESET  
OK  
ON:  
D0112-EN  
This function is turned on.  
OFF:  
2 Press the 6 buttons and chose  
the favourite channel that you want  
to delete  
This function is turned off.  
When you disconnect the AC plug, the  
CHILD LOCK will be cancelled.  
3 Press the blue button  
The chosen favourite channel and set  
contents are deleted.  
• For details of the favourite channels, see  
“Favourite channel function” on page 17.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
FEATURES menu  
ILLUMINATION  
You can choose one of three  
ILLUMINATION modes to adjust the  
illumination settings.  
SOFT:  
Softens illumination lights.  
BRIGHT:  
OFF:  
This function is turned off.  
• For the location of the illumination lamp,  
refer to page 9.  
MEDIA CARD VIEWER  
You can view photos taken with a digital  
camera or videos taken with a JVC digital  
media camera “Everio”. For details, see  
“Using a Media Card” on page 41  
• When a message “NO MEDIA  
DETECTED” appears, insert media card  
into the card slot. For details see “Using a  
Media Card” on page 41.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
SET UP menu  
• You can proceed to edit the  
programme numbers list using the  
EDIT/MANUAL function. For details,  
see “EDIT/MANUAL” on page 34.  
• If a TV channel you want to view is  
not stored in the programme numbers  
list, you can register it using the  
MANUAL function.  
SET UP  
AUTO PROGRAM  
EDIT/MANUAL  
LANGUAGE  
VIDEO-1 SETTING  
VIDEO-3 SETTING  
AI VOLUME  
VIDEO  
OFF  
TELETEXT LANGUAGE  
HDMI SETTING  
OK  
For details, see “EDIT/MANUAL” on  
page 34.  
D0029-EN  
• The AUTO PROGRAM function does  
not store a TV channel to the  
programme number PR 0 (AV).  
• If you do not need to use the EDIT/  
MANUAL function, press the a  
button to exit the EDIT menu.  
• Starting the AUTO PROGRAM  
deletes the registered favourite  
channel.  
AUTO PROGRAM  
You can again perform the AUTO  
PROGRAM function TV channel automatic  
registration which was performed in the  
“Initial settings (Setup tour)” (page 7).  
1 Choose AUTO PROGRAM, then  
press the a or 3 button  
The AUTO PROGRAM function starts.  
The TV channels you receive are  
automatically stored in the programme  
numbers list.  
EDIT/MANUAL  
The EDIT/MANUAL functions are divided  
into two types:  
>> AUTO PROGRAM  
• editing the current programme numbers  
(PR) (EDIT functions); and  
CH 28  
14%  
• manually storing a TV channel you want  
to view on a particular programme  
number (PR) (MANUAL function).  
OK  
Here are the details about these functions:  
D0004-EN  
MOVE:  
• To stop the AUTO PROGRAM  
This function changes the programme  
number (PR) of a TV channel.  
function, press the a button.  
2 After the TV channels have been  
stored in the programme number  
list, the EDIT menu appears  
ID:  
This function registers a channel name (ID)  
to a TV channel.  
INSERT:  
> EDIT  
This function adds a new TV channel in the  
current programme numbers (PR) list by  
using the CH/CC number.  
• You cannot use the INSERT function if  
you do not know the channel number of a  
TV channel. Use the MANUAL function  
to register a TV channel in the programme  
number (PR).  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH/CC  
CH  
CH  
CH  
CH  
CH  
CH  
CC  
CC  
CC  
21  
22  
23  
24  
25  
26  
01  
02  
03  
ID  
MANUAL  
OK  
MOVE  
INSERT DELETE  
D0038-EN  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
SET UP menu  
DELETE:  
This function deletes a TV channel you do  
not want to list.  
3 Press the a button to complete  
the settings  
MANUAL:  
This function manually stores a new TV  
channel in a programme number (PR).  
• For programme number PR 0, “AV”  
appears in the programme numbers (PR)  
list.  
• A VIDEO terminal number does not  
appear in the programme numbers (PR)  
list.  
Caution  
• Using the MOVE, DELETE or INSERT  
functions rewrites the current  
programme numbers (PR) list.  
Therefore, the programme numbers  
(PR) of some of the TV channels will  
change.  
• Using the MANUAL function for a TV  
channel for which the CHANNEL  
GUARD function has been set cancels  
the CHANNEL GUARD function for  
that channel.  
• The CH/CC number is a number unique to  
the TV and corresponds to the channel  
number of a TV channel. For the  
relationship between a channel number  
and a CH/CC number, see “CH/CC  
numbers” on page 51.  
MOVE  
• When a TV channel has already been  
registered in PR 99, using the INSERT  
function deletes that TV channel.  
1 Press the 6 buttons to choose a  
TV channel  
2 Press the 3 button to start the  
Basic operation  
MOVE function  
1 Choose EDIT/MANUAL, then press  
the a or 3 button  
> EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH/CC  
The EDIT menu appears.  
CH 21  
CH  
CH  
CH  
CH  
CH  
CC  
CC  
CC  
22  
23  
24  
25  
26  
01  
02  
03  
> EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH/CC  
CH  
CH  
CH  
CH  
CH  
CH  
CC  
CC  
CC  
21  
22  
23  
24  
25  
26  
01  
02  
03  
OK  
STORE  
D0030-EN  
ID  
MANUAL  
OK  
MOVE  
3 Press the 6 buttons to choose a  
INSERT DELETE  
D0038-EN  
new programme number (PR)  
To cancel the MOVE function:  
Press the b button.  
2 Follow the description for the  
function you want to use  
4 Press the 2 button to change the  
programme number (PR) of a TV  
channel to a new programme  
number (PR)  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP menu  
DELETE  
INSERT  
1 Press the 6 buttons to choose a  
1 Press the 6 buttons to choose a  
programme number (PR) for which  
you will register a new TV channel  
TV channel  
2 Press the yellow button to delete  
the TV channel  
2 Press the green button and start  
the INSERT function  
The TV channel is deleted from the  
programme numbers (PR) list.  
> EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH/CC  
ID  
CH  
CH  
CH  
CH  
CH  
CH  
CC  
CC  
CC  
21  
22  
23  
24  
25  
26  
1 Press the 6 buttons to choose a  
TV channel  
02  
03  
2 Press the red button to start the ID  
function  
OK  
0
9
CH/CC  
D0034-EN  
3 Enter a channel name (ID). Press  
the 6 buttons to choose a  
character. Press the 5 buttons to  
move the cursor  
3 Press the 6 buttons to choose  
“CC” or “CH” according to the CH/  
CC number of the TV channel  
> EDIT  
To cancel the INSERT function:  
Press the b button.  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH/CC  
CH  
CH  
CH  
CH  
CH  
CH  
CC  
CC  
CC  
21  
22  
23  
24  
25  
26  
01  
02  
03  
4 Press the number buttons to enter  
the remaining CH/CC number  
M
The TV shifts to registration mode. When  
the registration is completed, the picture  
of the TV channel appears on the screen.  
OK  
D0032-EN  
• The CH/CC number is a number given  
to each broadcast frequency that  
carries a TV channel. If the TV cannot  
detect the TV channel corresponding  
to the broadcast frequency indicated  
by the CH/CC number, a “no-signal”  
picture appears.  
To cancel the ID function:  
Press the b button.  
4 Press the a button to give a  
channel name to a TV channel  
Before performing INSERT operation  
• A CH/CC number unique to this TV and  
corresponding to the Channel number of a  
TV channel is required. Find the  
corresponding CH/CC number from a  
table “CH/CC numbers” on page 51 based  
on the Channel number of the TV  
channel.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
SET UP menu  
4 Press the green or red button to  
MANUAL  
search for a TV channel  
Scanning stops when the TV finds a TV  
channel. Then the TV channel is  
displayed.  
1 Press the 6 buttons to choose a  
programme number (PR) for a new  
TV channel  
2 Press the blue button to activate  
the MANUAL function  
5 Press the green or red button  
repeatedly until the TV channel you  
want appears  
At the right side following the CH/CC  
number, the SYSTEM (sound system) of  
the TV channel appears.  
If the TV channel reception is poor:  
Press the blue or yellow button to fine-  
tune the TV channel.  
> MANUAL  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH/CC  
CH  
CH  
CH  
CH  
CH  
CH  
CC  
CC  
CC  
21  
22  
23  
24  
25  
26  
If you cannot hear the normal  
sound even when the picture of the  
TV channel appears normally:  
The SYSTEM setting is wrong. Press the  
3 button and choose a SYSTEM that has  
normal sound.  
(
01 B / G  
)
02  
03  
SEARCH+  
FINE-  
OK  
SYSTEM  
FINE+  
SEARCH-  
D0035-EN  
6 Press the a button and register  
the TV channel to a Programme  
number (PR)  
To cancel the MANUAL function:  
Press the b button.  
The normal EDIT menu is resumed.  
3 Press the 3 button to choose the  
SYSTEM (sound system) for a TV  
channel you want to register  
• For the sound systems in each country  
or region, refer to the table below:  
Area  
Country or Region  
System  
Bahrain, Kuwait, Oman,  
Qatar, United Arab Emirates,  
Yemen, etc.  
Indonesia, Malaysia,  
Singapore, Thailand, India,  
etc.  
B/G  
Asia,  
Middle  
East  
China, Vietnam, etc.  
Hong Kong, etc.  
D/K  
I
Islamic Republic of Iran,  
Lebanon, Saudi Arabia, etc.  
B/G  
Philippines, Taiwan,  
Myanmar, etc.  
M
Russia, etc.  
D/K  
Czech Republic, Poland, etc. D/K  
Europe  
Germany, Holland, Belgium,  
etc.  
B/G  
UK, etc.  
I
Oceania Australia, New Zealand, etc. B/G  
Republic of South Africa, etc. I  
Africa Nigeria, etc.  
Egypt, Morocco, etc.  
B/G  
B/G  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP menu  
LANGUAGE  
AI VOLUME  
The LANGUAGE setting which was  
performed in the “Initial settings (Setup  
tour)” (page 7) can be changed.  
You can prevent the sudden increase or  
decrease of sound that occurs when changing  
the channel to another channel.  
ON:  
1 Choose LANGUAGE, then press  
the a or 3 button  
This function is turned on.  
A sub-menu of the LANGUAGE function  
appears.  
OFF:  
This function is turned off.  
• The AI VOLUME function may not  
operate as expected if the sound input  
level from a broadcast station is extremely  
low.  
LANGUAGE  
• This function does not work in the  
VIDEO mode.  
D1002-EN  
2 Press the 6 buttons to choose a  
language. Then press the a  
button  
VIDEO-1 SETTING/VIDEO-3  
SETTING  
Set the VIDEO-1 SETTING or VIDEO-3  
SETTING correctly according to the video  
connected to the VIDEO-1 or VIDEO-3  
terminal. If this setting is incorrect, images  
will not be displayed.  
VIDEO:  
If a normal video signal (composite video  
signal) is input.  
COMPONENT:  
If a Component video signal (Y, Cb/Pb, Cr/  
Pr signals) is input.  
• For detailed connecting methods, see  
“Additional preparation” on page 46. This  
Television is compatible with the 1080i  
(1125i), 576p (625p) or 480p (525p)  
video signal only when the component  
video signal is input.  
• When the input signal is 1080i (1125i),  
576p (625p) or 480p (525p), each signal  
type is displayed at the upper right side on  
the TV screen by setting the input to  
VIDEO-1 or VIDEO-3.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
SET UP menu  
TELETEXT LANGUAGE  
HDMI SETTING  
There are four types of teletext language  
groups. Set the teletext language group that  
corresponds to the language of the teletext  
programme that you want to watch.  
This function is used if you have a DVI or  
HDMI compatible device connected to your  
TV. For details, see “Using the HDMI  
terminal” on page 49.  
1 Choose TELETEXT LANGUAGE,  
then press the a or 3 button  
> TELETEXT LANGUAGE  
GROUP-1  
GROUP-2  
GROUP-3  
GROUP-4  
OK  
D1003-EN  
2 Press the 6 buttons to choose a  
group  
Group  
Languages  
GROUP-1  
Turkish, Hungarian, English,  
German, French, Italian, Spanish,  
Portuguese, Greek, Swedish,  
Finnish  
GROUP-2  
GROUP-3  
GROUP-4  
Polish, Serbian, Croatian,  
Slovenian, Czech, Slovak,  
Rumanian, Hungarian, German,  
French, Italian, Swedish, Finnish  
Russian, Bulgarian, Lettish,  
Lithuanian, Estonian, Ukrainian,  
Serbian, Croatian, Slovenian,  
Czech, Slovak, English, German  
Arabic, Czech, Slovak. Hungarian,  
English, German, French, Italian,  
Spanish, Portuguese, Swedish,  
Finnish  
3 Press the a button to complete  
the setting  
The menu disappears.  
• Languages that are not included in the  
teletext language group that you select,  
the sub-titles of the teletext programme  
will not be displayed properly.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Displaying a computer screen  
This TV can be used as a computer screen.  
Watching images from a  
computer  
Connecting to the computer  
Use a D-SUB cable to connect the TV’s PC  
IN terminal to the computer’s analogue RGB  
output terminal.  
If you want to listen to the sound from the  
computer, use an audio cable to connect the  
VIDEO-3 AUDIO L/R sound input terminal  
to the computer’s sound output terminal.  
When the sound from the computer is mono,  
connect to the VIDEO-3 AUDIO L terminal.  
After starting the computer, press the  
4 or 6 p buttons  
to choose “PC”  
You can listen to the sound when the  
sound from the computer is connected to  
the VIDEO-3 AUDIO L/R sound input  
terminal.  
• When the sound from the computer is  
connected to VIDEO-3, by choosing  
external input VIDEO-3 the sound  
from the computer can be listened to,  
but the images from the computer  
cannot be seen.  
IN (HDMI AUDIO)  
R
L
(ANALOG)  
IN  
Table of signals for each type  
of computer  
IN(HDMI AUDIO)  
(ANALOG)  
IN  
Resolution  
Vertical  
frequency  
(Hz)  
Horizontal  
frequency  
(kHz)  
640 × 480  
(VGA)  
60.0  
31.5  
1024 × 768  
(XGA)  
60.0  
42.0  
* Only the above formats are supported.  
* Even with the above formats and at  
60 Hz, some problems may be  
experienced depending on the quality of  
the synchronous signal. (Depending on  
the quality, some pictures may not be  
displayed properly.)  
* Apple Macintosh computers are not  
supported.  
When a picture is not displayed  
Check the computer’s refresh rate and set it  
to 60 Hz. Refer to the computer’s instruction  
manual.  
Computers which cannot have their refresh  
rate set to 60 Hz cannot be used with this  
unit.  
• Refer to the computer manual for a  
detailed explanation of the connections at  
the computer side.  
• Ensure that the connectors are facing the  
correct way when connecting.  
• After connecting the D-SUB cable,  
tighten the two screws to fix the connector  
in place.  
*
* Apple Macintosh is a registered  
trademark of Apple Computer, Inc.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Using a Media Card  
By inserting a media card into the TV, you can easily view photos taken with a digital camera or  
videos taken with a JVC digital media camera “Everio”.  
Supported Media Cards and file formats  
Readable Media Cards  
SD Memory Card, MultiMediaCard, Memory Stick (Memory Stick PRO is not supported), xD-Picture  
Card, CompactFlash and Microdrive Hard Disk for JVC digital media camera “Everio”.  
• Do not use any media card that is not specified. Otherwise, it may cause a malfunction.  
• Please read the instruction in this chapter carefully. Improper handling may destroy the data on  
a card or cause other problems to the TV and the card. JVC will not be responsible for any  
problems due to improper handling.  
• Operation can not be guaranteed if a card conversion adapter is used.  
Operation confirmed Cards  
Microdrive Hard Disk (*1)  
SD Memory Card  
Hitachi  
2GB, 4GB  
Panasonic  
LEXAR  
SanDisk  
LEXAR  
OLYMPUS  
Fujifilm  
SONY  
128MB, 256MB, 512MB, 1GB  
128MB  
32MB, 64MB, 128MB, 256MB  
512MB, 1GB  
CompactFlash  
xD-Picture Card  
256MB  
32MB, 64MB, 128MB  
64MB, 128MB  
Memory Stick  
*1: Only Microdrive Hard Disk usable for JVC digital media camera “Everio” has been confirmed.  
• Cards that are not listed above may not be operable or the data may be erased.  
• The above operation confirmed cards are not fully guaranteed to work with this TV.  
• Products and company names included in this instruction manual are trademarks and/or  
registered trademarks of their respective holders.  
Compatible file formats  
The file formats that are not listed below are not compatible with this TV. Even if they are listed  
below, they are not fully guaranteed to work correctly.  
Formats  
Photo JPEG  
Standard  
Codec  
Size (pixcels) / Rate Extension  
Exif 2.0, JFIF,  
DCF 2.0  
JPG, jpg,  
160 × 120 to 2560 × 1920  
JPEG, jpeg  
JPEG  
720 × 576 / PAL,  
MPEG-2-PS  
(*1)  
Video: MPEG-2-PS MP/ML 352 × 288 / PAL,  
SD-VIDEO  
MOD, mod  
Audio: Dolby Digital (*2)  
720 × 480 / NTSC,  
352 × 240 / NTSC  
Video  
Video: MPEG-4  
Simple profile  
Audio: G.726  
352 × 288 / 30 frames,  
240 × 176 / 15 frames,  
160 × 120 / 5 frames  
MPEG-4  
(*3)  
SD-VIDEO  
ASF  
ASF, asf  
*1: MPEG-2-PS files can only be read in slot for the Microdrive Hard Disk and CompactFlash.  
Only MPEG-2-PS recorded by JVC Digital media card camera “Everio” can be played back.  
*2: Audio must be Dolby Digital enable to playback the sound data.  
*3: MPEG-4 files may not be detected or played back correctly.  
• Manufactured under license from Dolby Laboratories. “Dolby”, and the double-D symbol are  
trademarks of Dolby Laboratories.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Using a Media Card  
Inserting the Media Card  
Open the door on the left side panel by gently pushing the “PUSH-OPEN” on the door and insert  
the Media Card. Once you have inserted the media card, the message “PLEASE CLOSE THE  
DOOR” will appear on the screen. Then, close the door. MEDIA CARD VIEWER will start up.  
Follow the description “Using the MEDIA CARD VIEWER” on page 43.  
Caution  
• When it cannot be inserted smoothly, do not force it but check the card direction again.  
• Do not remove the card before stopping “MEDIA CARD VIEWER”. Otherwise, the TV  
may not operate properly or the data on the card may be destroyed.  
To insert  
To eject  
Ridge  
Left side panel  
Left side panel  
• If you do not close the door, it will not operate.  
• Recognition of the card can take significantly more time if the card contains a large number of  
files.  
• When a message “NO MEDIA DETECTED” appears, insert the card again.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Using a Media Card  
3 Remove the media card from the  
card slot  
Using the MEDIA CARD  
VIEWER  
See “Inserting the Media Card” on  
page 42.  
• You can also start the MEDIA CARD  
VIEWER by choosing MEDIA CARD  
VIEWER (see page 33) in the  
FEATURES menu.  
SELECT ONE AND PRESS OK:  
PHOTO  
VIDEO  
FILE  
• Displaying interval of photos may vary  
depending on the size of the file.  
• Noise may appear during the slideshow.  
• When each file uses a different recording  
format, the screen is temporarily  
disturbed.  
• Only the first 8 characters of the  
FOLDER or FILE name are displayed.  
Double-byte characters cannot be  
displayed.  
D5006-EN  
If you have two media cards inserted  
in the card slot:  
Select the card you want to view from the  
menu below.  
SELECT ONE AND PRESS OK:  
SD Card  
• Folders and files are displayed in  
alphabetical order.  
COMPACT FLASH  
• The date will not be displayed when there  
is no information in the file.  
• Motion JPEG is not compatible with this  
TV.  
D5010-EN  
• Files edited or saved on your PC may not  
be played back correctly.  
If there are no files:  
Following message will be displayed.  
NO FILE IN THIS MODE  
1
Follow the description for the  
function you want to use  
PHOTO:  
You can view photos that are stored on  
your media card.  
VIDEO:  
You can view videos that are stored on  
your media card.  
FILE:  
You can use file name to search for  
photos and videos you want to display.  
2 Press the 4 button to stop  
the MEDIA CARD VIEWER  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Using a Media Card  
PHOTO  
VIDEO  
1 Choose VIDEO. Then press the a  
1 Choose PHOTO. Then press the  
a button  
button  
CF  
CF  
PAGE  
0001/  
0002  
PAGE  
0001/  
0002  
D5021-EN  
D5012-EN  
2 Press the 7 buttons to  
choose the image. Then press the  
a button  
2 Press the 7 buttons to  
choose the image. Then press the  
a button  
The slide show starts.  
The video show starts.  
To pause:  
Press the a button. To play again, press  
the a button.  
To pause:  
Press the a button. To play again, press  
the a button.  
To stop:  
Press the b button.  
To fast-forward/reverse:  
Press the 5 buttons.  
To select:  
Press the 5 buttons.  
To stop:  
Press the b button.  
To rotate the photo:  
Press the a button to pause. Then press  
the 6 buttons.  
• Videos are played in alphabetical order  
of the file names.  
• Screen size depends on the recorded  
picture size. (ZOOM function is not  
available.)  
• Photos are shown in alphabetical order  
of the file names.  
• Screen size is automatically adjusted.  
(ZOOM function is not available.)  
• The slide show interval cannot be  
changed.  
• Rotaded photo data cannot be saved  
(over-written) to the card.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using a Media Card  
FILE  
1 Choose FILE. Then press the a  
button  
The FILE LIBRARY menu appears.  
FILE LIBRARY  
CARD  
JVC01  
JVC02  
JVC03  
JVC04  
JVC05  
JVC06  
JVC07  
Folder : CARD  
D5015-EN  
SD 0000/0007  
2 Press the 6 buttons to choose  
the folder in the left frame. Then  
press the a button  
FILE LIBRARY  
File size :  
Date :  
12KB  
..  
08/10/2005  
DSC0001  
DSC0002  
DSC0003  
DSC0004  
DSC0005  
DSC0006  
DSC0007  
Folder : JVC01  
D5020-EN  
SD 0001/0007  
3 Press the 6 buttons to choose  
the image in the left frame. Then  
press the a button  
To pause:  
Press the a button. To play again, press  
the a button.  
To stop:  
Press the b button.  
To return to the previous folder (  
Press the 1 button to select a folder on  
top, then press the a button.  
..  
):  
• Photos and videos are played in  
alphabetical order of the file names.  
• Operations other than play/pause/stop  
can not be made.  
• When different types of file format is  
placed under the same folder, files may  
not be played back correctly. Be sure  
to place the files into a separate folders  
for each format.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional preparation  
Connecting external equipment  
Connect the equipment to the TV, making  
the correct rear panel and front panel  
connections.  
1 VCR (composite signal)  
2 VCR (S-VIDEO signal; Y/C)  
3 VCR for recording (composite signal)  
4 DVD player (composite signal)  
5 DVD player (S-VIDEO signal; Y/C)  
6 TV game (composite signal)  
7 TV game (S-VIDEO signal; Y/C)  
8 Headphones  
9 Camcorder (composite signal/S-VIDEO  
signal; Y/C)  
0 DVD player (component video signals; Y,  
Pb/Cb, Pr/Cr)  
Before connecting anything:  
• Read the manuals that came with the  
equipment.  
Depending on the equipment, the  
connection method may be different from  
the diagram. Also, the equipment settings  
may need to change depending on the  
connection method.  
• Turn off all the equipment including the TV.  
• The “Specifications” on page 54 give the  
details of the VIDEO terminals. If you are  
following connection diagram, see the  
table to choose the best VIDEO terminal.  
• Connecting cables are not supplied.  
connect the VCR’s AUDIO OUT (audio  
output) terminal and the TV’s VIDEO-3  
AUDIO L terminal with an audio cable.  
• Use the supplied cable to connect the  
component device to the VIDEO-1  
COMPONENT Y Pb/Cb Pr/Cr terminal.  
- Video cable  
~ S-VIDEO cable  
! Component cable  
Connecting the PC  
For details, see “Connecting to the computer”  
on page 40.  
Using a Media Card  
For details, see “Using a Media Card” on  
page 41.  
Using the HDMI terminal  
For details, see “Using the HDMI terminal”  
on page 49.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Additional preparation  
OUT  
OUT  
Supplied cable  
(Component video cable)  
IN (HDMI AUDIO)  
R
L
(ANALOG)  
IN  
IN(  
HDMM  
I
AUD  
IO)  
(A  
NALOG)  
IN  
without terminal covers  
IN  
OUT  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional preparation  
Connecting headphones  
Connect the headphones with a stereo mini-  
jack (3.5 mm diameter) to the headphone  
jack.  
without terminal covers  
• No sound comes from the TV speakers  
when the headphones are connected.  
IN (HDMI AUDIO)  
L
(ANALOG)  
TV output from the OUT terminal  
The video/sound signal of a TV channel you  
are viewing is always output from the OUT  
terminal.  
IN  
• No signal will output through the S VIDEO  
terminal when you are not viewing images  
coming from the S VIDEO input. In this  
case, use the VIDEO terminal instead of  
the S VIDEO terminal.  
R
L
IN  
(HDMI  
AUDI  
O)  
(A  
NALOG)  
• Changing over a programme number (PR)  
also changes over the TV output from the  
OUT terminal.  
IN  
• When using the VIDEO-1 COMPONENT  
Y Pb/Cb Pr/Cr terminal input, VIDEO-3  
COMPONENT input VIDEO-4 (HDMI)  
input or PC IN input, the sound signal is  
output from the OUT terminal but the  
picture signal is not output.  
1
2
Amplifier  
External speakers (Magnetic-shielded type)  
• Teletext programmes cannot be output.  
• The output from the OUT terminal is not  
interrupted by headphone connection to  
the TV. You cannot cut the sound from  
the front speaker even if you connect a  
headphone to the TV.  
Connecting speakers/amplifier  
While referring to the audio equipment  
connection diagram, connect the audio  
equipment you want to the TV.  
You can use external front speakers to listen  
to the TV sound instead of the TV speakers.  
• Adjust the volume of the external  
speakers with the amplifier.  
Before connecting anything:  
• Read the manuals provided with the  
amplifier and speakers.  
• Turn the TV and amplifier off.  
• Note that connecting cables are not  
supplied.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional preparation  
Using the HDMI terminal  
Connecting a HDMI compatible device  
Connecting a HDMI compatible device such as a DVD player or DVR allows you to display high  
definition pictures on your TV in their digital form.  
Connect the HDMI cable from the digital out on the back of your HDMI device to the  
HDMI terminal on the back of the TV.  
DIGITAL OUT  
"HDMI the HDMI l
High-Definition Multimedia  
Interface are trademarks or  
H
Back of the TV  
HDMI cable  
When you connect as shown above, set AUDIO in HDMI SETTING menu in the SET UP menu  
to AUTO or DIGITAL. Refer to “Setting HDMI SETTING” below.  
• To connect the DVI device to the HDMI terminal, connect the DVI terminal of the DVI device to  
the HDMI terminal of the TV with the DVI-HDMI converter cable, and the audio output terminal  
of the DVI device to the IN(HDMI AUDIO) L/R terminal of the TV with the audio cable.  
When these connections are made, set AUDIO in HDMI SETTING menu to AUTO or ANALOG.  
Refer to “Setting HDMI SETTING” below.  
• The HDMI terminal is not compatible with the picture signal of a personal computer.  
The HDMI of the TV is compatible with the following video signals.  
VGA/60Hz  
4:3  
4:3  
16:9  
16:9  
4:3  
576p/50Hz (625p/50Hz)  
576p/50Hz (625p/50Hz)  
720p/50Hz (750p/50Hz)  
720p/60Hz (750p/60Hz)  
1080i/50Hz (1125i/50Hz)  
1080i/60Hz (1125i/60Hz)  
4:3  
480i/60Hz (525i/60Hz)  
480i/60Hz (525i/60Hz)  
480p/60Hz (525p/60Hz)  
576i/50Hz (625i/50Hz)  
576i/50Hz (625i/50Hz)  
16:9  
16:9  
16:9  
16:9  
16:9  
16:9  
Setting HDMI SETTING  
1 Press the H button and display the menu bar, press the 5 buttons and  
choose SET UP, and press the 6 buttons and choose HDMI SETTING, and  
press then a button  
The HDMI SETTING menu appears.  
> HDMI SETTING  
SIZE  
AUDIO  
AUTO  
AUTO  
OK  
D0060-EN  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Additional preparation  
2 Press the 6 buttons and choose SIZE or AUDIO  
• SIZE can only be chosen when the picture signal is VGA or 480p.  
When setting SIZE:  
This option adjusts the position when a VGA or 480p picture signal is being displayed on the  
screen. If the displayed picture is slightly shifted, the position can be adjusted by choosing 1, 2  
or AUTO.  
1, 2 or AUTO can be chosen by pressing the 5 buttons.  
When setting AUDIO:  
Choose DIGITAL when only connecting with the HDMI cable.  
Chose ANALOG when a DVI device is connected to the HDMI terminal and the audio output  
terminal of the DVI device is connected to the IN(HDMI AUDIO) terminal.  
Choose AUTO when you want the TV to automatically select DIGITAL or ANALOG.  
DIGITAL, ANALOG or AUTO can be chosen by pressing the 5 buttons.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CH/CC numbers  
When you want to use the INSERT function on page 36, find the CH/CC number corresponding to  
the Channel number of the TV channel from this table.  
US:  
The US channel numbers are the channel numbers used in the United States,  
Philippines, etc.  
CCIR:  
OIRT:  
The CCIR channel numbers are the channel numbers used in the Middle East,  
Southeast Asia, etc.  
The OIRT channel numbers are the channel numbers used in Eastern Europe, Russia,  
Vietnam, etc.  
AUSTRALIA: The AUSTRALIA channel numbers are the channel numbers used in Australia, etc.  
Channel  
Channel  
CH  
US  
CCIR  
OIRT  
AUSTRALIA  
AU-0  
CC  
US  
CCIR  
OIRT  
AUSTRALIA  
AU-5  
CH02  
CH03  
CH04  
CH05  
CH06  
CH07  
CH08  
CH09  
CH10  
CH11  
CH12  
CH13  
CH14  
CH15  
CH16  
CH17  
CH18  
CH19  
CH20  
CH21  
CH22  
CH23  
CH24  
CH25  
CH26  
CH27  
CH28  
CH29  
CH30  
CH31  
CH32  
CH33  
CH34  
CH35  
CH36  
CH37  
CH38  
CH39  
CH40  
CH41  
CH42  
CH43  
CH44  
CH45  
CH46  
CH47  
CH48  
CH49  
CH50  
CH51  
CH52  
CH53  
CH54  
CH55  
CH56  
CH57  
CH58  
CH59  
CH60  
CH61  
CH62  
CH63  
CH64  
CH65  
CH66  
CH67  
CH68  
CH69  
US-2  
US-3  
US-4  
US-5  
US-6  
US-7  
US-8  
US-9  
US-10  
US-11  
US-12  
US-13  
E2  
E3  
E4  
E5  
E6  
E7  
E8  
E9  
R1  
CC01  
CC02  
CC03  
CC04  
CC05  
CC06  
CC07  
CC08  
CC09  
CC10  
CC11  
CC12  
CC13  
CC14  
CC15  
CC16  
CC17  
CC18  
CC19  
CC20  
CC21  
CC22  
CC23  
CC24  
CC25  
CC26  
CC27  
CC28  
CC29  
CC30  
CC31  
CC32  
CC33  
CC34  
CC35  
CC36  
CC37  
CC38  
CC39  
CC40  
CC41  
CC42  
CC43  
CC44  
CC45  
CC46  
CC47  
CC48  
CC49  
CC50  
CC51  
CC52  
CC53  
CC54  
CC55  
CC56  
CC57  
CC58  
CC59  
CC60  
CC61  
CC62  
CC63  
CC64  
CC75  
CC76  
CC77  
CC78  
CC79  
CC95  
CC96  
CC97  
CC98  
CC99  
S-1  
S-2  
S-3  
S-4  
S-5  
S-6  
S-7  
S-8  
AU-1  
AU-2  
AU-6  
AU-7  
AU-8  
AU-9  
R2  
R6  
R7  
R8  
R9  
AU-5A  
E10  
E11  
E12  
R10  
R11  
R12  
AU-10  
AU-11  
S-9  
S-10  
S-11  
S-12  
S-13  
S-14  
S-15  
S-16  
S-17  
S-18  
S-19  
S-20  
S-21  
S-22  
S-23  
S-24  
S-25  
S-26  
S-27  
S-28  
S-29  
S-30  
S-31  
S-32  
S-33  
S-34  
S-35  
S-36  
S-37  
S-38  
S-39  
S-40  
S-41  
US-14, W+29  
US-15, W+30  
US-16, W+31  
US-17, W+32  
US-18, W+33  
US-19, W+34  
US-20, W+35  
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
W+1  
W+2  
W+3  
W+4  
W+5  
W+6  
W+7  
W+8  
W+9  
W+10  
W+11  
W+12  
W+13  
W+14  
W+15  
W+16  
W+17  
W+18  
W+19  
W+20  
W+21  
W+22  
W+23  
W+24  
W+25  
W+26  
W+27  
W+28  
US-21, W+36 E21  
US-22, W+37 E22  
US-23, W+38 E23  
US-24, W+39 E24  
US-25, W+40 E25  
US-26, W+41 E26  
US-27, W+42 E27  
US-28, W+43 E28  
US-29, W+44 E29  
US-30, W+45 E30  
US-31, W+46 E31  
US-32, W+47 E32  
US-33, W+48 E33  
US-34, W+49 E34  
US-35, W+50 E35  
US-36, W+51 E36  
US-37, W+52 E37  
US-38, W+53 E38  
US-39, W+54 E39  
US-40, W+55 E40  
US-41, W+56 E41  
US-42, W+57 E42  
US-43, W+58 E43  
US-44, W+59 E44  
US-45, W+60 E45  
US-46, W+61 E46  
US-47, W+62 E47  
US-48, W+63 E48  
US-49, W+64 E49  
US-50, W+65 E50  
US-51, W+66 E51  
US-52, W+67 E52  
US-53, W+68 E53  
US-54, W+69 E54  
US-55, W+70 E55  
US-56, W+71 E56  
US-57, W+72 E57  
US-58, W+73 E58  
US-59, W+74 E59  
US-60, W+75 E60  
US-61, W+76 E61  
US-62, W+77 E62  
US-63, W+78 E63  
US-64, W+79 E64  
US-65, W+80 E65  
US-66, W+81 E66  
US-67, W+82 E67  
US-68, W+83 E68  
US-69, W+84 E69  
X
Y
Z
Z+1  
Z+2  
R3  
R4  
R5  
AU-3  
AU-4  
A-5  
A-4  
A-3  
A-2  
A-1  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Troubleshooting  
If a problem arises while you are using the TV, please read this troubleshooting guide carefully  
before you ask to have the TV repaired. You may be able to fix it easily by yourself. For example,  
if the mains plug is disconnected from the mains outlet, or the TV aerial has problems, you may  
think there is a problem with the TV itself.  
Important:  
• This troubleshooting guide only covers problems whose causes are not easy to decide. If you  
have a question when you are operating a function, read the page(s) for that function carefully,  
not this troubleshooting guide.  
• If you follow the advice in this troubleshooting guide without any success, unplug the mains  
plug and ask for your TV to be repaired. Do not attempt to repair the TV by yourself or to  
remove the rear cover of the TV.  
– Have the TV and aerial been connected  
properly?  
– Has the aerial cable been damaged?  
– Is the aerial pointing in the right  
direction?  
If you cannot turn on the TV  
• Is the mains plug connected to the mains  
outlet?  
• Make sure you set the PIP/TV/DVD  
switch to the TV position. You cannot  
turn the TV on when the PIP/TV/DVD  
switch is set to the DVD position.  
– Is the aerial itself faulty?  
• If the TV or aerial suffers interference  
from other equipment, stripes or noise  
may appear in the picture. Move any  
equipment such as an amplifier, personal  
interference away from your TV. Or try  
moving the TV. If the aerial suffers  
interference from a radio tower or high-  
dealer.  
• If the TV suffers interference from signals  
reflecting from mountains or buildings,  
double-pictures (ghosting) will occur. Try  
to change the aerial’s direction or replace  
it with one with better directionality.  
• Are your COLOUR SYSTEM settings  
correct? Follow the description  
If you cannot turn off the TV  
switch to the TV position. You cannot  
turn the TV off when the PIP/TV/DVD  
switch is set to the DVD position.  
No picture or no sound  
• Have you chosen a TV channel with very  
poor reception? If so, the BLUE BACK  
function will be activated: the entire  
screen becomes blue, and the sound is  
muted. If you still want to view the TV  
channel, follow the description “BLUE  
BACK” on page 32 to change the BLUE  
BACK function setting to OFF.  
• If the SYSTEM setting for a TV channel  
is incorrect, it may prevent the sound  
from being issued. Follow the description  
“EDIT/MANUAL” on page 34 to use the  
MANUAL function to try to change the  
SYSTEM setting.  
“COLOUR SYSTEM” on page 26 to try  
to solve the trouble.  
• Have the COLOUR and BRIGHT settings  
been adjusted properly? Follow the  
description “BRIGHT” and “COLOUR”  
on page 24 to try to adjust them properly.  
• Videotaping teletext is not recommended  
because it may not record correctly.  
• When viewing images from commercially  
available video software products, or  
videos from videotapes which have been  
recorded improperly, the top of the image  
may be distorted. This is due to the  
condition of the video signal. There is  
nothing wrong with the TV.  
Poor picture  
• If noise (snow) totally blocks out the  
picture, there may be a problem with the  
aerial or aerial cable. Check the following  
to try to solve the problem:  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Troubleshooting  
• Since this TV is designed to make full use  
source, the motion may appear unnatural  
when the video source is input with  
progressive-scanning component signals.  
If this occurs, change the output setting of  
scanning component signal output. See  
the instructions that came with the device  
for more information.  
Other issues  
• If the CHILD LOCK function set to ON,  
you cannot operate the TV with the front  
control buttons of the TV. Set the CHILD  
LOCK function to OFF.  
• When the SLEEP TIMER function or  
AUTO SHUTOFF function operates, the  
TV is automatically turned off. If the TV  
suddenly turns off, try to press the #  
(standby) button to turn on the TV once  
again. If the TV goes back to normal,  
there is no problem.  
Poor sound  
• Have you adjusted BASS or TREBLE  
properly? If not, follow the description  
“BASS” or “TREBLE” on page 28.  
• When TV channel reception is poor, it can  
be hard to hear stereo or bilingual sound.  
In this case, follow the description  
“STEREO / I • II” on page 28 to hear the  
sound more easily by changing it to a  
mono sound.  
• When the TV is receiving a wide-screen  
device affecting the screen size, the  
ZOOM mode automatically changes.  
When you want to resume the previous  
ZOOM mode, press the c button  
again.  
• It takes a short period of time from the  
time an operation such as changing  
channels is performed until an image is  
displayed. This is not a fault. This is the  
time needed for the image to stabilise  
before it can be displayed.  
• The TV may make a crackling sound due  
to a sudden change in temperature. The  
picture or sound may be normal. If you  
hear crackling sounds frequently while  
you are viewing the TV, there may be  
other causes. As a precaution, ask your  
service technician to inspect it.  
• The top of the TV and the screen may  
become hot during use but this has no  
affect on the performance of the TV.  
Make sure that the ventilation holes are  
not blocked.  
• When the picture is unstable, the screen  
may become white for a moment. This  
happens when the signal which drives the  
liquid crystal is missing. This is not a  
fault.  
• When a still image has been displayed for  
a long period, a faint residual image may  
remain on the screen for a short time after  
the power has been turned off or when  
another image is displayed. This is not a  
fault and the image will eventually  
disappear.  
If the TV does not respond to the  
remote control  
• Have the batteries of the remote control  
worn out? Follow the description “Putting  
the batteries into the remote control” on  
page 7 and replace them with new batteries.  
• Have you attempted to use the remote  
control from the sides or rear of the TV or  
from more than seven metres away from the  
TV? Use the remote control in front of your  
TV or from less than seven metres away.  
• When you are viewing a teletext  
programme, you cannot operate the  
menus. Press the 4 button to  
return to the ordinary TV programme, and  
then try operating the menus.  
• If the TV suddenly stops responding,  
disconnect the power cord of the TV from  
the AC outlet. Connect them to the AC  
outlet again to turn on the TV. If the TV  
returns to a normal state, it is not a failure.  
• When a media card is inserted into the  
TV, remove the card first. Then unplug  
TV, several minutes later plug it in again.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Model  
LT-Z37DX5  
Broadcasting systems  
Colour systems  
B, G, I, D, K, K1, M  
PAL, SECAM, NTSC 3.58/4.43 MHz  
Channels and frequencies  
VHF low channel (VL) = 46.25 to 168.25 MHz  
VHF high channel (VH) = 175.25 to 463.25 MHz  
UHF channel (U) = 471.25 to 863.25 MHz  
• Receives cable channels in mid band (X to Z+2, S1 to S10), super band (S11  
to S20) and hyper band (S21 to S41).  
Sound-multiplex systems  
NICAM (B/G, I, D/K) system, A2 (B/G, D/K) system  
Languages displayed by  
teletext  
Please see the table in the description “TELETEXT LANGUAGE” on page 39.  
Teletext systems  
Power requirements  
Power consumption  
Screen size  
Audio output  
Speakers  
FLOF (Fastext), WST (World Standard System)  
110 - 240 V AC, 50/60 Hz  
173 W (Standby: 2.6 W)  
Viewable area 94.9 cm (measured diagonally)  
Rated Power output: 10 W + 10 W  
6.6 cm round × 4  
VIDEO-1 terminal  
(COMPONENT)  
RCA connector × 3, S VIDEO connector × 1, Component connector × 1  
• Video input, S VIDEO (Y/C) input, Component video (Y, Cb/Pb, Cr/Pr) input  
and Audio L/R inputs are available.  
• 480i (525i), 480p (525p), 576i (625i), 576p (625p), 1080i (1125i), 720p/60  
(750p/60) signals are available.  
VIDEO-2 terminal  
RCA connector × 3, S VIDEO connector × 1  
• Video input, S VIDEO (Y/C) input and Audio L/R inputs are available.  
VIDEO-3 terminal  
(COMPONENT)  
RCA connector × 6  
• Video input, Component video (Y, Cb/Pb, Cr/Pr) input and Audio L/R inputs are  
available.  
• 480i (525i), 480p (525p), 576i (625i), 576p (625p), 1080i (1125i), 720p/60  
(750p/60) signals are available.  
VIDEO-4 (HDMI) terminal  
IN(HDMI AUDIO) terminal  
OUT terminal  
HDMI connector × 1  
• Digital video input and digital audio input available. (Refer to page 49 for details.)  
RCA connector × 2  
• Audio L/R inputs are available. (Refer to page 49 for details.)  
RCA connectors × 3, S VIDEO connector × 1  
• Video output, S VIDEO (Y/C) output and Audio L/R outputs are available.  
• Output level 0.5 Vrms.  
PC IN terminal  
Multi Card Slot  
Analogue RGB D-SUB (15 pin) × 1  
• PC signal is available. Refer to page 40 for details of the signals which can be  
input.  
Slot (Small) × 1, Slot (Large) × 1  
(Refer to page 41 for details.)  
Headphone jack  
Stereo mini-jack (3.5 mm in diameter)  
Dimensions (W × H × D)  
926 mm × 687 mm × 325 mm  
926 mm × 632 mm × 109 mm (without stand)  
Weight  
27.7 kg  
20.7 kg (without stand)  
Accessories  
Remote control unit × 1 (RM-C1830)  
AA/R6 dry cell battery × 2  
Component video cable × 1  
We may change the design and specifications without notice.  
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any  
commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of  
the owners of copyright of the original picture sources, as this would be an infringement of  
copyright.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
© 2005 Victor Company of Japan, Limited  
0905TKH-CR-VP  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Insignia Handheld TV NS 7HTV User Manual
Intel Computer Hardware SE7500WV2 User Manual
JVC Digital Camera VN C205 User Manual
Kambrook Hot Beverage Maker KCT110 User Manual
Kawasaki Impact Driver 690163 User Manual
Kenmore Water Heater 153339482 User Manual
Kenwood CRT Television KMT 5032 User Manual
Kenwood Marine Radio 762G User Manual
Kicker Car Amplifier DXA1252 User Manual
KitchenAid Ventilation Hood MICROWAVE HOOD User Manual