JVC Flat Panel Television 50059704 User Manual
ENGLISH  
LT-30E45SJ  
INSTRUCTIONS  
WIDE LCD PANEL TV  
50059704  
©2004 VICTOR COMPANY OF JAPAN, LIMITED  
1004MKH-VT-VT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Important Instruction  
For your own safety read following instruction  
carefully before attempting to connect this unit  
to the mains supply.  
Important Instruction .............................. 1  
How to remove the stand ........................ 2  
Important Information ............................. 3  
TV Control Buttons and Terminals ......... 4  
Remote Control Buttons.......................... 6  
Preparation .............................................. 7  
Safety Precautions.................................. 7  
Before Switching On Your TV ................. 9  
Switching The TV ON/OFF ....................... 9  
Operating The TV................................... 10  
Other Features....................................... 18  
Teletext................................................... 21  
Connect Peripheral Equipment ............ 22  
Antenna Connections ............................ 24  
PC Input Typical Display Modes ............ 25  
PIP Combination Restrictions............... 25  
Tips ......................................................... 26  
Specifications ........................................ 27  
MAINS (AC) OPERATION  
The wires in this mains lead are coloured in  
accordance with the following code :  
BLUE-NEUTRAL  
BROWN-LIVE  
As the colours of the wires in the mains lead  
of this appliance may not correspond with the  
coloured markings identifying the terminals  
in your plug, proceed as follows:  
The wire which is coloured blue must be  
connected to the terminal which is marked  
with the letter N or coloured black.  
The wire which is coloured brown must be  
connected to the terminal which is marked  
with the letter L or coloured red.  
No connection is to be made to the earth  
terminal of the plug.  
If a 13 Amp (BS 1363) Plug is used a 5 Amp  
Fuse must be fitted, or if any other type of Plug  
is used a 5 Amp Fuse must be fitted, either in  
the Plug of Adaptor, or on the Distribution  
Board.  
CAUTION  
TO PREVENT ELECTRIC SHOCK DISCONNECT  
FROM THE MAINS BEFORE REMOVING COVER.  
NO USER SERVICEABLE PARTS INSIDE. REFER  
SERVICING TO QUALIFIED SERVICE PERSONNEL.  
SAFETYPRECAUTION  
THIS EQUIPMENT MUST BE DISCONNECTED FROM  
THE MAINS WHEN NOT IN USE. DO NOT ALLOW  
THIS UNIT TO BE EXPOSED TO RAIN OR MOISTURE.  
ENGLISH - 1 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
• Do not allow children to hang from the TV, place their elbows on the TV or lean against the TV.  
Doing so may cause the TV to fall over and lead to injuries.  
CAUTION:  
• The TV screen may be damaged if the TV is carried as shown in the diagram below.  
The TV should always be carried by two people.  
How to remove the stand  
ENGLISH - 2 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Information  
Please take note  
EXCLUSION CLAUSE  
JVC shall under no circumstances be liable for loss and/or damage to the product caused  
by:  
• fire;  
• earthquake;  
• accidental damage;  
• intentional misuse of the product;  
• use of the product in improper conditions;  
• loss and/or damage caused to the product whilst in the possession of a third party;  
• any damage or loss caused as a result of the owner’ s failure and/or neglect to follow the  
instructions set out in the owner’s manual;  
• any loss or damage caused directly as a result of misuse or malfunction of the product  
when used simultaneously with associated equipment;  
Furthermore, under no circumstances shall JVC be liable for any consequential loss and/  
or damage including but not limited to the following, loss of profit, interruption of business,  
the loss of recorded data whether caused during normal operation or misuse of the  
product.  
WARNING! NEVER LEAVEA  
Care and disposal  
STATIONARY IMAGE ON THE  
SCREEN  
Cleaning the screen and cabinet...  
If stationary images generated by TELETEXT,  
CHANNELIDENTIFICATIONLOGOS, COM-  
PUTER DISPLAYS, VIDEO GAMES, ON  
SCREEN MENUS, etc. are left on the TV  
screen for any length of time, they could be-  
come permanently ingrained.  
Turn off the power, clean the screen and cabi-  
net with a soft, dry cloth. We recommend that  
you do not use any proprietary polishes or  
solvents on the screen or cabinet as this may  
cause damage.  
If you use your television to display completely  
still images, or moving pictures which have a  
permanent still image superimposed e.g.  
broadcast network logos, it is always advis-  
able to reduce BOTH the brightness and con-  
trast settings.  
Disposal...  
When the set reaches the end of its useful  
life please dispose of it in accordance with  
Local Government Regulations or at a recy-  
cling centre.  
ENGLISH - 3 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV Control Buttons and Terminals  
FRONT VIEW  
REAR VIEW  
ENGLISH - 4 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Headphone  
Audio Input (Left, Right)  
Video Input  
S-VHS Input  
FrontAV  
STAND BY button  
TV/AV button  
MENU button  
Program Up, Program Down buttons  
Volume Up, Volume Down buttons  
Power cord input  
On/Off switch  
Antenna  
Audio Line Out L, R  
Scart 1  
Scart 2  
Audio In (for PC)  
PC Input  
TV Control Buttons  
ENGLISH - 5 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Buttons  
ꢀ
ꢁ
ꢁꢂ  
/ I = (Stand By) button  
TV / VCR / DVD Switch  
Number buttons  
AV button (Tuner, Scart 1, Scart 1 RGB,  
Scart 2, Scart 2 RGB, PC, FAV, SVideo)  
ꢂ
BLUE / PICTURE Mode button  
YELLOW /  
Sleep Timer button  
MENU button  
ꢁꢁ  
ꢁꢀ  
ꢁꢆ  
$9  
ꢃ
ꢉ
= Cursor Up button  
OK button  
ꢇ
ꢄ
= Cursor Right button  
BACK button  
ꢀꢅ  
ꢈ
= Volume + / - buttons  
Teletext / VCR / DVD Control buttons  
PIP Control Buttons  
ꢅ
ꢀꢈ  
ꢀꢆ  
ꢀꢀ  
ꢀꢄ  
ꢀꢇ  
P
buttons  
= Cursor Down button  
= Teletext Button  
ꢀꢉ  
ꢀꢁ  
= Cursor Left button  
= Stereo / Bilingual button  
3
GREEN /  
Hyper Sound On/Off button  
RED / ZOOM Mode button  
= Information Button  
= Mute button  
ꢀꢂ  
ꢀꢃ  
79  
ENGLISH - 6 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Stereo PC Audio Input  
• 4H Comb Filter  
Preparation  
For ventilation, leave a space of at least 10 cm  
free all around the set. To prevent any fault  
and unsafe situations, please do not place  
any objects on top of the set.  
• Audio Line Out  
Panel Features  
• High resolution, 30-inch TFT LCD display.  
• WXGA resolution (1280 x 768)  
• Contrast ratio (600:1 typical)  
Use this apparatus in tropical and/or moder-  
ate climates.  
Features  
• Brightness (typical) 550 cd/m2.  
• It is a remote controlled color television.  
• Response time (typical) 25 msec.  
• 100 programmes from VHF, UHF bands or  
cable channels can be preset.  
• Viewing angle (typical) 170° (horizontal) and  
170° (vertical).  
• It can tune cable channels.  
• Display color 16.7 Million.  
• Controlling the TV is very easy by its menu  
driven system.  
Safety Precautions  
1. Power Source  
• It has 2 Euroconnector sockets for external  
devices (such as video, video games, audio  
set, etc.)  
The receiver should be operated only from a  
220 - 240 V AC, 50 Hz. outlet. Ensure you se-  
lect the correct voltage setting for your conve-  
nience.  
• Stereo sound system (German+Nicam).  
• Full function Teletext .  
Fastext (10 Pages), TOP text.  
• It is possible to connect headphone.  
• Direct channel access.  
2. Power Cord  
The power supply cord should be placed so  
that it is not likely to be walked on or pinched  
by items placed upon them or against it. Pay  
particular attention to cord where it enters the  
plug, power outlet, and the point where it exits  
from the receiver.  
• A.P.S. (Automatic Programming System).  
• All programmes can be named.  
• Sleep timer.  
• Automatic sound mute when no transmis-  
sion.  
3. Moisture and Water  
• Auto, Full, 16:9 Zoom,16:9 Zoom Subtitle,  
Regular, Panoramic, 14:9 Zoom modes.  
Auto switch WSS (Wide Screen Signaling).  
Do not use this equipment in a humid and  
damp place (avoid the bathroom, the sink in  
the kitchen, and near the washing machine).  
Do not expose this equipment to rain or water,  
as this may be dangerous and do not place  
objects filled with liquids on top. Avoid from  
dripping or splashing.  
• NTSC Playback.  
• Front SVHS is available.  
• Front AV in is available.  
• It has VGA connector for external devices such  
as computer.  
4. Cleaning  
• It has PIP functions.  
• TV Picture in PC  
Before cleaning, unplug the receiver from the  
main supply, outlet. Do not use liquid or aero-  
sol cleaners. Use soft and dry cloth.  
• When no valid signal is detected, after 5 min-  
utes the TV switches itself automatically to  
stand-by mode.  
5. Ventilation  
The slots and openings on the receiver are  
intended for ventilation and to ensure reliable  
operation. To prevent overheating, these open-  
• PC input (Support Up to WXGA 1280 x 768)  
• 1 SVHS Input and 1 RCA AV Input are avail-  
able.  
ENGLISH - 7 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ings must not be blocked or covered in any-  
way.  
6. Lightning  
In case of storm and lightning or when going  
on holiday, disconnect the power cord from  
the wall outlet.  
7. Replacement Part  
When replacement parts are required, be sure  
the service technician has used replacement  
parts which are specified by the manufacturer or  
have the same specifications as the original one.  
Unauthorised substitutions may result in fire,  
electrical shock, or other hazards.  
8. Servicing  
Please refer all servicing to qualified person-  
nel. Do not remove cover as this may result in  
electric shock.  
9. Naked Flame Sources  
Do not place naked flame sources on the ap-  
paratus.  
WARNING: When the device is not in use for  
a long time, disconnect from power.  
"The LCD panel is very high technology prod-  
uct with about a million thin film transistors,  
giving you fine picture details. Occasionally,  
a few non-active pixels may appear on the  
screen as a fixed point of blue, green or red.  
Please note that this does not affect the per-  
formance of your product."  
Instructions for waste disposal:  
• Packaging and packaging aids are recy-  
clable and should principally be recycled.  
Packaging materials, such as foil bag, must  
be kept away from children.  
• Battery, including those which is heavy metal-  
free, should not be disposed of with house-  
hold waste. Please dispose of used battery  
in an environmentally sound manner. Find  
out about the legal regulations which apply  
in your area.  
“DO NOT LEAVEYOUR TVAT STAND-BYOR  
OPERATING WHEN YOU LEAVE YOUR  
HOUSE”  
• Cold cathode fluoresant lamp in LCD PANEL  
contains a small amount of mercury, please  
follow local ordinates or regulations for dis-  
posal.  
ENGLISH - 8 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BeforeSwitchingOnYourTV  
Power Connection  
IMPORTANT: The TV set is designed to oper-  
ate on 220 - 240 V AC, 50 Hz.  
• After unpacking, allow the TV set to reach the  
ambient room temperature before you con-  
nect the set to the mains.  
Connections To The RF Input  
Socket  
NOTE: Remove batteries from remote con-  
trol handset when it is not to be used for a long  
period.Otherwise it can be damaged due to  
any leakage of batteries.  
• Connect the aerial or cable TV plug to the RF  
input socket located at the back of the TV  
and connect the cable plug coming out from  
the TV out socket located at the devices (VCR,  
DVB etc.) to this socket as well.  
Switching The TV ON/OFF  
To switch the TV on:  
Your TV will switch on in two steps:  
1- Connect the power supply cord to the sys-  
tem. Press On/Off switch at the rear of the  
TV. Then the TV switches itself to stand-by  
mode and the power lamp becomes red lo-  
cated on the front of the TV.  
2- To switch on the TV from stand-by mode  
either:  
Press a digit button on the remote control so  
that a programme number is selected,  
How To Connect Other Devices  
or,  
IMPORTANT: Switch off the TV before connect-  
ing any external device.  
Press “ / I”, "-P/CH" or "P/CH+" button at the  
top of the TV or press “  
” or “  
” button  
Sockets for external connections are at the  
back and side of the TV. For connection of other  
devices via Euroconnector refer to the manu-  
als of the related devices.  
on the remote control, so that last switched off  
programme is selected.  
By either ways the TV will switch on and the  
power lamp becomes green.  
Inserting Batteries In The Remote  
Control Handset  
To switch the TV off:  
• Press the “stand-by” button on the remote  
control, so the TV will switch to stand-by  
mode and the power lamp will become RED,  
• Place the batteries in the right directions as  
seen below.  
• Remove the battery cover located on the back  
of the handset by gently pulling upwards from  
the indicated part.  
or,  
Press the “ / I” button located on the top of  
the TV, so the TV will switch off and the power  
lamp will become RED.  
• Insert two AA/R6 dry cell or equivalent type  
of batteries inside.  
To switch the TV off completely press On/Off  
switch at the rear of the TV and remove the  
mains plug from the socket.  
• Replace the battery cover.  
ENGLISH - 9 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Volume Setting  
Operating The TV  
Press “VOLUME -” button to decrease volume  
or “VOLUME +” button to increase volume, so  
a volume level scale (slider) will be displayed  
at the middle of the bottom on the screen.  
You can operate your TV both using the re-  
mote control handset and onset buttons.  
Initial APS (Automatic Programming  
System)  
The following menu will be displayed on the  
screen when you turn on your TV for the first  
time. APS, searches and sorts all channels  
and stores them automatically on your TV, ac-  
cording to the transmission of programme  
systems in your area.  
Programme Selecting  
Press “P/CH+” button to select the next  
programme or “PCH-” button to select the pre-  
vious programme.  
“P/CH+ / PCH-” and “VOLUME + / VOLUME -”  
buttons on the TV are used as navigation but-  
tons in menu.  
Entering The Menu  
Press “MENU” button at the control panel on  
the top of the TV to enter the menu.  
“P/CH+ / PCH-” and “VOLUME + / VOLUME -”  
buttons at the control panel on the top of the  
TV work as direction buttons in the menu.  
To cancel APS before starting, press “BACK”  
button.  
EXT Mode  
First of all choose language and country by  
Press “TV/AV” button at the control panel on  
the top of the TV to switch your TV to EXT mode  
(See EXT Modes in page 20).  
using “ “ / “ ” and “ “ / “ ” buttons. This,  
will effect the sort process in APS. To start aps  
select autoset, by using “ “ / “ ” buttons  
Operating With Remote Control  
and press “ “ / “ ” or “OK” button. WhileAPS  
is running, no picture appears.  
The remote control handset of your TV is de-  
signed to control all the functions of the model  
you selected. The functions will be described  
in accordance with the menu system of your  
TV.  
Functions of the menu system are described  
in Menu System section.  
AfterAPS is finalized, the programme table will  
be appeared on the screen. In the programme  
table you will see the programme numbers  
and names assigned to the programmes.  
Volume Setting  
Press “  
+” button to increase volume.  
If you do not accept the locations and / or the  
programme names of programmes, you can  
change them in aps submenu in the settings  
menu. (See page 17 for Program table expla-  
nation.)  
Press “-  
” button to decrease volume.  
A volume level bar will be displayed at the  
middle of the bottom on the screen.  
Operating with the buttons on the  
TV set  
Volume setting and programme selection can  
be made by using the buttons at the control  
panel on the top of the TV.  
ENGLISH - 10 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programme Selecting (Previous or next  
programme)  
ton. One programme is displayed on the whole  
screen at this option.  
pip  
• Press “  
” button to select the previous  
programme.  
By pressing “ “ / “ ” button, select pip.  
“<ok> activates pip window layout” is seen  
• Press “  
” button to select the next  
programme.  
on the screen. Press “ ” or “OK” button. The  
first programme can be watched on the back-  
ground. The second programme is seen at  
the pip window.  
Programme Selecting (direct access):  
Press digit buttons on the remote control hand-  
set to select programmes between 0 and 9.  
TV will switch to the selected program after a  
short delay.  
PIP picture is displayed on the screen also  
with “  
Programme in the PIP window is increased /  
decreased by “ ” , digit buttons or  
AV button when PIP window is selected. PIP  
” button.  
• For a two digit program number enter the  
second digit after pressing the first digit within  
2 seconds.  
/
Menu System  
window is removed from the screen by “  
button.  
”
Your TV has been designed with a menu sys-  
tem to provide an easy manipulation of a mul-  
tifunction system. Press the “MENU” button to  
enter the menu.  
picture menu  
By pressing “ “ / “ ” button, select the sec-  
ond icon. Picture menu appears on the screen.  
Press “ “ / “ ” button to select a menu title  
and then “ “ / “ ” button to select a menu  
item and “ “ / “ ” or “OK” button to enter the  
submenu. Press “MENU” button to return to  
the previous menu. Press “BACK” button to  
exit from the menu.  
layout menu  
By pressing “ “ / “ ” button, select the first  
icon. Layout menu appears on the screen.  
brightness  
By pressing “ “ / “ ” button, select bright-  
ness. “right/left to adjust brightness” is seen  
on the screen. Press “ ” button to increase  
brightness. Press “ “ button to decrease  
brightness. Brightness level can be adjusted  
between 0 and 100.  
contrast  
By pressing “ “ / “ ” button, select contrast.  
“right/left to adjust contrast” is seen on the  
full screen  
screen. Press “ ” button to increase contrast.  
By pressing “ “ / “ ” button, select full  
screen. “<ok> activates one window layout”  
Press “ “ button to decrease contrast. Con-  
trast level can be adjusted between 0 and 100.  
is seen on the screen. Press “ ” or “OK” but-  
ENGLISH - 11 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
sharpness  
brightness  
By pressing “ “ / “ ” button, select sharp-  
ness. “right/left to change sharpness” is seen  
By pressing “ “ / “ ” button, select bright-  
ness. “right/left to adjust brightness” is seen  
on the screen. Press “ ” button to increase  
on the screen. Press “ ” button to increase  
sharpness. Press “ “ button to decrease  
sharpness. Sharpness level can be adjusted  
between 0 and 8.  
brightness. Press “ “ button to decrease  
brightness. Brightness level can be adjusted  
between 0 and 100.  
color  
contrast  
By pressing “ “ / “ ” button, select color.  
“right/left to adjust color” is seen on the  
By pressing “ “ / “ ” button, select contrast.  
“right/left to adjust contrast” is seen on the  
screen. Press “ ” button to increase color.  
screen. Press “ ” button to increase contrast.  
Press “ “ button to decrease color. Color level  
can be adjusted between 0 and 100.  
Press “ “ button to decrease contrast. Con-  
trast level can be adjusted between 0 and 100.  
tint  
phase  
This item is displayed in picture menu when  
TV is in AV mode and at NTSC signal. By  
pressing “ “ / “ ” button, select tint. "right/  
left to adjust tint" is seen on the screen. Press  
By pressing “ “ / “ ” button, select phase.  
"right/left to adjust phase" is seen on the  
screen. Press “ ” button to increase phase.  
Press “ “ button to decrease phase. Phase  
level can be adjusted between 0 and 100.  
“ ” button to increase tint. Press “ “ button  
to decrease tint. Tint level can be adjusted be-  
tween 0 and 100.  
window menu  
By pressing “ “ / “ ” button, select the third  
icon. Window menu appears on the screen.  
• If full screen option was selected at the lay-  
out menu, the window menu is seen as be-  
low.  
When TV is in AV mode; picture menu items  
(brightness, contrast, sharpness and color)  
may require re-adjustment.  
When PC is Connected To TV:  
image size  
By pressing “ “ / “ ” button, select image  
size. "right/left to change image size" is seen  
on the screen. By pressing “ “ / “ ” button,  
you can change image size to Auto, Full, 16:9  
Zoom, 16:9 Zoom Subtitle, Regular, Pan-  
oramic, 14:9 Zoom modes.  
You can enter image size directly by pressing  
“ZOOM” button.  
ENGLISH - 12 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• If pip option was selected, the window menu  
is seen as below.  
When PC Is Connected To TV  
image size  
By pressing “ “ / “ ” button, select image  
size. "right/left to change image size" is seen  
image size  
on the screen. By pressing “ “ / “ ” button,  
you can change image size to Fill all, Fill 1:1  
and Fill aspect.  
By pressing “ “ / “ ” button, select image  
size. "right/left to change image size" is seen  
on the screen. By pressing “ ” / “ ” button,  
you can change image size to full, regular and  
auto.  
h position  
By pressing “ “ / “ ” button, select h posi-  
tion. "right/left to adjust h position" is seen  
You can enter image size directly by pressing  
“ZOOM” button. See Page 20 for details.  
on the screen. Press “ ” button to slide the  
pip size  
screen to the left. Press “ “ button to slide  
screen to the right. h position can be adjusted  
between 0 and 100.  
By pressing “ “ / “ ” button, select pip size.  
"right/left to adjust PIP size" is seen on the  
v position  
screen. Press “ ” button to increase pip size.  
By pressing “ “ / “ ” button, select v posi-  
tion. "right/left to adjust v position" is seen  
Press “ “ button to decrease pip size. Pip  
size can be adjusted between 0 and 100.  
on the screen. Press “ ” button to slide the  
When PIP is activated you can enter the pip  
screen to up. Press “ “ button to slide screen  
to down. v position can be adjusted between  
0 and 100.  
size directly by pressing “  
” button.  
pip position  
By pressing “ “ / “ ” button, select pip posi-  
tion. "right/left to adjust PIP position" is  
audio menu  
By pressing “ “ / “ ” button, select the fourth  
icon. Audio menu appears on the screen.  
seen on the screen. By pressing “ “ / “ ”  
button, you can change the pip position as left  
top, right top, middle, left bottom or right bot-  
tom (as seen on the menu above).  
When PIP is activated you can change pip po-  
sition directly by pressing "  
" button.  
ENGLISH - 13 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
volume  
“MENU” button to exit the equalizer menu.  
By pressing “ “ / “ ” button, select volume.  
"right/left to adjust volume" is seen on the  
screen. Press “ ” button to increase volume  
level. Press “ “ button to decrease volume  
level. Volume level can be adjusted between  
0 and 63.  
hyper sound  
hp volume  
It is used to gain saloon effect to the sound.  
By pressing “ “ / “ ” button, select hp vol-  
ume. "right/left to adjust hp volume" is seen  
By pressing “ “ / “ ” button, select hyper  
sound. "right/left for wide sound off/stereo/  
mono" is seen on the screen. By pressing  
on the screen. Press “ ” button to increase  
headphone volume level. Press “ “ button to  
decrease headphone volume level. Hp vol-  
ume (headphone volume) level can be ad-  
justed between 0 and 100.  
“ “ / “ ” button set to hyper sound on to  
activate it or off to deactivate it.  
dynamic bass  
hp sound mode  
Dynamic Bass is used to increase bass ef-  
fect of the TV set.  
By pressing “ “ / “ ” button, select hp sound  
mode. "right to adjust hp sound mode" is  
By pressing “ “ / “ ” button, select dynamic  
bass. "right/left for dynamic bass on/off" is  
seen on the screen. Press “ “ / “ ” button  
change hp sound mode.  
seen on the screen. By pressing “ “ / “ ”  
button set to dynamic bass on to activate it or  
off to deactivate it.  
Hp sound mode is used to identify sound mode  
of the headphone. hp sound mode can be set to  
mono, stereo, dual a or dual b according to the  
transmission.  
options menu  
By pressing “ “ / “ ” button, select the fifth  
icon. Options menu appears on the screen.  
balance  
By pressing “ “ / “ ” button, select balance.  
"right/left to adjust balance" is seen on the  
screen. Press “ ” button to increase balance  
rightward. Press “ “ button to decrease bal-  
ance leftward. Balance level can be adjusted  
between -50 and 50.  
equalizer  
By pressing “ “ / “ ” button, select equal-  
izer. "right/left for equalizer settings" is seen  
on the screen. Press “ “ / “ ” or “OK” button  
to enter equalizer menu. In equalizer menu  
the sound mode can be changed to user, flat,  
language  
pop, rock, jazz and classic by pressing “ “ /  
By pressing “ “ / “ ” button, select lan-  
guage. "right/left to change language" is  
“ ” button. Equalizer menu settings can be  
changed only when sound mode is user. Se-  
lect the desired frequency by “ “ / “ ” button  
and increase or decrease the frequency gain  
seen on the screen. By pressing “ “ / “ ”  
button, you can select the language.  
by pressing “ “ / “ ” button.  
ENGLISH - 14 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
vcr  
scart 2 out  
This item is displayed only when TV is in AV  
mode. By pressing “ “ / “ ” button, select  
vcr. "right/left to change vcr status" is seen  
By pressing “ “ / “ ” button, select scart 2  
out. "right/left to select scart 2 out" is seen on  
the screen. You can set scart 2 out to Scart 1,  
on the screen. By pressing “ “ / “ ” button  
tuner or FAV by pressing “ “ / “ ” button.  
set vcr to on or off.  
sleep timer  
By pressing “ “ / “ ” button, select sleep  
timer. "adjust sleeptimer" is seen on the  
screen. The Sleep Timer is used to turn the  
TV off after a defined period of time after se-  
lecting this item. The timer can be pro-  
grammed between 0 and 120 minutes in  
steps of 10 minutes. (0, 10, 20, 30, 40, ... ,  
120)  
If sleep timer is activated, at the end of the  
selected the time, the TV goes automatically  
to stand-by mode.  
settings menu  
osd timeout  
By pressing “ “ / “ ” button, select the sixth  
icon. Settings menu appears on the screen.  
By pressing “ “ / “ ” button, select osd  
timeout. "right/left to change osd timeout"  
• If full screen option was selected at the lay-  
out menu, the settings menu is seen as be-  
low.  
is seen on the screen. By pressing “ “ / “ ”  
button, you can change osd timeout to 5 sec,  
15 sec or 60 sec.  
menu background  
By pressing “ “ / “ ” button, select menu  
background. "right to change menu back-  
ground" is seen on the screen. You can  
change menu background to translucent or  
opaque by pressing “ ” button.  
If pip option was selected at the layout menu  
or in AV mode, the settings menu is seen as  
below.  
child lock  
You can use this feature to prevent children  
turning on TV or changing programs or ad-  
justments etc. without remote control.  
By pressing “ “ / “ ” button, select child  
lock. "right/left to change" is seen on the  
screen. The child lock feature can be set by  
“ “ / “ ” button to either on or off. When off is  
selected, there will be no difference in the op-  
eration of your TV. When on is selected, the TV  
can only be controlled by the remote control  
handset.  
tv tuner  
By pressing “ “ / “ ” button, select tv tuner.  
"OK to activate tuner menu" is seen on the  
screen. By pressing “ “ / “ ” or “OK” button  
ENGLISH - 15 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
enter the menu. tv tuner menu has two sub-  
menu named as aps and programming.  
standard  
By pressing “ “ / “ ” button, select stan-  
dard. “right/left to change standard” is seen  
programming menu  
on the screen. By pressing “ “ or “ ” button,  
you can change the standard to B/G, D/K, I or  
L/L'.  
By pressing “ “ / “ ” button in tv tuner menu  
select the first icon. Programming menu ap-  
pears on the screen.  
channel type  
By pressing “ “ / “ ” button, select channel  
type. "right/left to change channel type" is  
seen on the screen. By pressing “ “ or “ ”  
button, you can change the channel type to C  
or S.  
edit labels  
By pressing “ “ / “ ” button, select edit la-  
bels. "right/left to edit labels" is seen on the  
screen. By pressing “ “ / “ ” or “OK” button,  
you can enter the following menu.  
program  
By pressing “ “ / “ ” button, select program.  
"right/left to select program" is seen on the  
screen. By pressing “ “ or “ ” button, you  
can select the program number. You can also  
enter a number via digit buttons on the remote  
control. There are 100 program storage be-  
tween 0 and 99.  
“
“ / “ ” or “ “ / “ ” buttons are used to  
edit labels.  
store program  
By pressing “ “ / “ ” button, select store  
program. "right/left to store program" is  
fine tune  
By pressing “ “ / “ ” button, select fine tune.  
"right/left to adjust fine tuning" is seen on  
seen on the screen. By pressing “ “ / “ ” or  
“OK” button, you can store the program and  
following menu appears on the screen.  
the screen. By pressing “ “ or “ ” button, you  
can adjust the tuning. The adjust values are  
between -50 and +50.  
channel  
By pressing “ “ / “ ” button, select channel.  
"right/left to change channel" is seen on the  
manual search  
screen. By pressing “ “ or “ ” button, you  
can change the channel number. You can also  
enter a number via digit buttons on the remote  
control. The adjust values change according  
to the standard and channel type.  
By pressing “ “ / “ ” button, select manual  
search. "right/left to search" is seen on the  
screen. By pressing “ “ or “ ” button, you  
can start program searching and following  
menu appears on the screen.  
ENGLISH - 16 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
In program table, “ “ / “ ” buttons work like  
"Direction Up" and "Direction Down". By cur-  
sor action, programme selection is done au-  
tomatically.  
Programme Number is between 01 and 99.  
00 is not displayed on program table.  
Programme Name has a name string with 5  
characters. After autoset process the  
Programme Names are set to "C02" or "S07"  
(channel type and channel number) or name  
of the tuned channel if defined.  
aps menu  
By pressing “ “ / “ ” button in tv tuner menu  
select the second icon. aps menu appears  
on the screen.  
At the bottom of the program table there is a  
programme sort functions section. Each func-  
tion is activated by color button (seen above).  
By Delete you can delete programmes that  
you decided. Insert section is for inserting  
programmes into another programme  
spaces. Name allows changing the  
programme name.  
Delete:  
For "Delete" process RED button is pressed.  
The following warning menu comes to screen.  
Pressing “MENU” button cancels the activated  
"Delete" process. Pressing “OK” button  
erases the selected programme from the  
programme list, and the programmes below  
shift one up.  
program table  
By pressing “ “ / “ ” button, select program  
table. "right/left to enter program table" is  
seen on the screen. By pressing “ “ / “ ” or  
“OK” button, you can enter the following pro-  
gram table.  
• Program table may be entered only when the  
layout is full screen. You can not enter to  
program table when layout is pip screen.  
ꢀ0(18!  
ꢀ2.!  
Insert:  
Select the program which you want to insert  
by navigation buttons. Press GREEN button.  
By cursor buttons move the selected program  
to the decided programme space and press  
GREEN button again.  
Name:  
To change the name of a decided programme,  
that programme is selected and pressed to  
the YELLOW button. The following menu  
comes to screen.  
Moving cursor to four direction you can reach  
30 programmes in the same page. By scroll-  
ing the pages up or down by pressing the cur-  
sor buttons you can select all the  
programmes in TV mode (except the AV  
mode).  
ENGLISH - 17 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The first letter of the selected name is high-  
lighted. To change that letter “ “ / “ ” button  
can be used, and to select the other letters,  
source select  
By pressing “ “ / “ ” button, select source  
select in settings menu. "<ok> to activate  
source selection menu" is seen on the  
“ “ / “ ” button can be used. If the cursor is  
at the last letter of the Programme Name,  
screen. By pressing “ “ / “ ” or “OK” button,  
you can enter the source select menu.  
pressing “ ” button moves the cursor at the  
beginning. On the contrary, if the cursor is at  
the beginning of the Programme Name,  
pressing “ “ button moves the cursor at the  
end.  
country  
By pressing “ “ / “ ” button, select country.  
"right/left to change country" is seen on the  
screen. By pressing “ “ / “ ” button, you  
should select the country where you are.  
autoset  
By pressing “ “ / “ ” button, select autoset.  
"right/left to start aps function" is seen on  
In source select menu, come on one of the  
sources by pressing “ “ / “ ” button and  
the screen. When “ “ / “ ” or “OK” button is  
pressed, the following menu comes to the  
screen. If you want to cancel autoset function,  
press “MENU” button. You return to aps menu.  
select it by pressing “ ” button. The source  
types are Tuner, Scart 1, Scart 1 RGB,  
Scart 2, Scart 2 RGB, PC, FAV and S-Video.  
If you press “MENU” button after autoset is  
started, program table appears on the screen.  
Other Features  
TV Status  
Programme Number, Programme Name  
and Sound Indicator are displayed on the up-  
per right side of the screen. Source is also  
displayed with them on the right bottom side  
of the screen. They are displayed after  
programme change during 3 seconds or  
ꢀ0(18!  
ꢀ2.!  
If “OK” button is pressed, autoset function starts  
and the following menu comes to the screen.  
when “ ” button is pressed.  
Programme Number  
ꢀꢁꢀ  
35ꢀꢁꢂꢀ  
Programme Name (5 characters)  
ꢃ
After autoset is finalized, the program table  
comes to the screen.In the programme table  
you will see the programme numbers and  
names assigned to the programmes.  
These OSD’s are displayed when a new pro-  
gramme is entered by digit button, by press-  
ing “  
” or “  
” button or “BACK” but-  
ton.  
If you do not accept the locations and / or the  
programme names of programmes, you can  
change them in aps submenu in the settings  
menu. (See page 17 for Program table expla-  
nation.)  
Pressing “  
” button when PC mode se-  
lected shows sound indicator and the resolu-  
tion of the screen.  
When “ ” button is pressed twice the cur-  
ENGLISH - 18 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
In Mono broadcast or in forced-mono (for ste-  
reo broadcast).  
rent time information, captured from Teletext  
will be displayed on the screen.  
67(5(2  
In Stereo broadcast.  
'8$/ꢀ$  
Active window switch  
By pressing “  
” button in any modes, PIP  
window appears on the screen.  
If dual broadcast detected. Dual A is selected  
in default and also can be selected  
In PIP mode “ “ / “ ” buttons or “ ” button  
are used to select active window.  
after Dual B by Remote Control.  
'8$/ꢀ%  
If Dual B selected by Remote Control.  
Muting the Sound  
Press the " "(muting) button to turn off and  
on the sound. One of the sound marks below  
will appear on the upper left side of the screen.  
The mark will also appear when the left or  
Right button pressed.  
It is placed in the upper left side of the screen  
when enabled.  
Note: PC screen is not displayed in PIP win-  
dow.  
Sound Off  
Sound On  
Freeze Picture  
When sound is off, pressing "  
+" / "-  
"
You can freeze the picture on the screen by  
pressing “OK” button. Press OK button again  
to back to the moving picture. Display layout  
should be selected as full screen for this fea-  
ture. At PIP layouts; this function is invalid.  
buttons restores the previous volume level  
Sleep Timer  
Sleep Timer mode OSD is displayed when  
YELLOW button is pressed.  
The Sleep Timer is used to turn the TV off after  
a defined period of time after selecting this  
item. The timer can be programmed between  
0 and 120 minutes in steps of 10 minutes. (0,  
10, 20, 30, 40, ... , 120)  
If PIP layout is selected, the sound mark is  
displayed at the upper middle of the PIP win-  
dow.  
If sleep timer is activated, at the end of the  
selected the time, the TV goes automatically  
to stand-by mode.  
Hyper Sound  
By selecting Hyper Sound in sound menu or  
by pressing the “  
“ button on your remote  
Sound Modes  
control, Pseudo/Spatial effect can be turned  
on or off. In Mono transmission the left and  
right channels will be added at left channel  
and dummy stereo effect will introduced to  
end-user.  
The alternatives of the modes are Mono, Ste-  
reo, Dual A and Dual B. This indicator is dis-  
played under the programme number indica-  
tor on the screen. "I-II" button is used to select  
Mono, Stereo, Dual A or Dual B.  
In stereo transmission it yields a phase dif-  
0212  
ENGLISH - 19 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ference between left and right channels. Hyper  
Sound selection will be displayed on the  
screen when the TV Status button is pressed  
or programme is changed.  
• For 16:9 aspect ratio pictures that have been  
squeezed into a normal picture (4:3 aspect  
ratio), use the FULL mode to restore the pic-  
ture to its original shape.  
16:9 ZOOM:  
EXT Modes  
This zooms up the wide picture (16:9 aspect  
ratio) to the full screen.  
By pressing the “AV“ button or via source se-  
lect menu, you can switch your TV to EXT  
modes (except being in Teletext). Pressing this  
button will consecutively switch the TV in one  
of the optional EXT modes: Tuner, Scart 1,  
Scart 1 RGB, Scart 2, Scart 2 RGB, PC, FAV  
and SVideo.  
16:9ZOOM SUBTITLE:  
While watching VCR; vcr item in options menu  
should be set to on.  
This zooms up the wide picture (16:9 aspect  
ratio) with subtitles to the full screen.  
Zoom Modes  
Zoom mode bar is displayed when RED  
button(ZOOM) is pressed. You can change the  
screen size according to the picture aspect  
ratio. Select the optimum one from the follow-  
ing ZOOM modes.  
REGULAR:  
Use to view a normal picture (4:3 aspect ratio)  
as this is its original shape.  
AUTO:  
When a WSS (Wide Screen Signalling) sig-  
nal, which shows the aspect ratio of the pic-  
ture, is included in the broadcast signal or the  
signal from an external device, the TV auto-  
matically changes the ZOOM mode to 16:9  
ZOOM mode PANORAMIC or FULL mode ac-  
cording to the WSS signal.  
PANORAMIC:  
This stretches the left and right sides of a nor-  
mal picture (4:3 aspect ratio) to fill the screen,  
without making the picture appear unnatural.  
• When the AUTO mode does not function cor-  
rectly due to poor WSS signal quality or when  
you want to change the ZOOM mode, change  
to another ZOOM mode manually.  
Using the different screen formats  
The top and bottom of the picture are slightly  
cut off.  
Press the “ “ or “ ” button to select the differ-  
ent modes: Auto, Full, 16:9 Zoom,16:9 Zoom  
Subtitle, Regular, Panoramic, 14:9 Zoom  
modes.  
14:9 ZOOM:  
This zooms up the wide picture (14:9 aspect  
ratio) to the upper and lower limits of the  
screen.  
FULL:  
This uniformly stretches the left and right sides  
of a normal picture (4:3 aspect ratio) to fill the  
wide TV screen.  
ENGLISH - 20 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ber, “ ” sign will replace the page number  
and flash until the entered page number is  
found. Then the page number will replace  
Teletext  
Teletext is an information system that displays  
text on your TV screen. Using the Teletext in-  
formation system you can view a page of in-  
formation on a subject that is available in the  
list of contents (index).  
“
” sign again. Now you can display this  
teletext page pressing “ “ button  
To Select Double Height Text  
The menu is not available in text mode.  
• Press “  
“ button for the top half of the infor-  
Contrast, brightness or colour control is not  
available, but volume control is available in  
text mode.  
mation page to be displayed in double height  
text.  
• Press “  
“ button again for the bottom half  
To Operate Teletext  
of the information page to be displayed in  
double height text.  
• Select a TV station on which Teletext is being  
transmitted.  
• Press “  
“ button once more for the full  
page of normal height text.  
• Press “  
” button. Usually the list of con-  
tents (index) is displayed on the screen.  
To Reveal “Concealed”  
Information  
• Pressing “  
“ button once will reveal an-  
swers on a quiz or games page.  
• Pressing “  
“ button again will conceal the  
revealed answers.  
To Select a Page Of Teletext  
To Stop Automatic Page Change  
• Press the appropriate digit buttons for the  
required Teletext page number.  
The teletext page you have selected may con-  
tain more information than what is on the  
screen; the rest of the information will be dis-  
played after a period of time.  
The selected page number is displayed at the  
top left corner of the screen. The Teletext page  
counter searches until the selected page  
number is located, so that the desired page is  
displayed on the screen.  
• Press “  
“ button to stop the automatic  
page change.  
• Press “  
” button to move the Teletext  
• Press “  
“ button again to allow the next  
screen forward one page at a time.  
page to be displayed.  
• Press “  
” button to move the Teletext  
To Select A Subcode Page  
screen backward one page at a time.  
Subcode pages are subsections of long Tele-  
text pages that can only be displayed on the  
screen one section at a time.  
To Select Index Page  
• To select the page number of the index (gen-  
• Select the required Teletext page.  
erally page 100), press “  
“ button.  
Searching for a teletext page while • Press “  
“ button.  
watching TV  
• Select the required subcode page number  
by pressing four digit buttons (e.g. 0001).  
• In the Teletext mode pressing “ “ button  
will switch the screen to the TV mode. In the  
TV mode enter a page number using digit  
buttons. As you enter last digit of page num-  
• If the selected subcode page is not displayed  
in a short time, press “  
“ button. TV  
programme will be displayed on the screen.  
ENGLISH - 21 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Teletext page number will be displayed on  
the upper left corner of the screen when the  
selected page is found.  
Connect Peripheral  
Equipment  
There is a wide range of audio and video equip-  
ment that can be connected to your TV.  
• Press “  
Teletext page.  
“ button to display the selected  
The following connection diagrams show you  
where the different equipment should be con-  
nected at the back or right side of the TV.  
To Exit Teletext  
• Press “ ” button. The screen will switch to  
TV mode.  
Via The Euroconnector  
Fastext  
TFT TV has 2 Euroconnector sockets. If you  
want to connect peripherals (e.g. video, de-  
coder, etc.) which have Euroconnectors, to the  
TV, use Scart 1 or Scart 2 inputs.  
Your TV supports the 10 page Teletext system.  
When the page number of any of the 10 pages  
in memory is entered, the system will not search  
for the requested page; instead it will display the  
page automatically.  
If an external device is connected via Euro-  
connector sockets TV is switched to EXT mode  
automatically. If the signal is RGB, select RGB  
in the source select menu to view picture. If  
the external device is connected to Scart 1,  
choose Scart 1 RGB. If the external device is  
connected to Scart 2, choose Scart 2 RGB.  
• Press “  
screen forward one page at a time.  
” button to move the Teletext  
• Press “  
” button to move the Teletext  
screen backward one page at a time.  
For Fastext  
Via Ant Input  
The subject-heading for the information may  
have a particular color.  
If you want to connect to your TV, peripherals  
like video recorders or decoders, but the de-  
vice you want to connect does not have Euro-  
connector, you should connect it to the ANT  
input of the TV.  
• Press an appropriate RED, GREEN, YELLOW  
or BLUE button in order to reach the relevant  
page quickly.  
For TOP text  
If the VCR is connected via antenna input it  
is suggested to use the Programme 0.  
TOP text mode of operation will be activated  
automatically according to the transmission.  
Decoder  
• If TOP text transmission is present, color  
coded buttons will appear in status row.  
Cable TV offers you a wide choice of programs.  
Most of them are free, others are to be paid for  
by the viewer. This means that you will need to  
subscribe to the broadcasting organisation  
whose programmes you wish to receive. This  
organisation will supply you a corresponding  
decoder unit to allow the programmes to be  
unscrambled.  
• If TOP text transmission is not present, sta-  
tus row will not appear.  
The subject-heading for information may be  
located in colored box.  
In Top mode the “  
or  
” commands  
will request the next or previous page respec-  
tively. If TOP text transmission is not available,  
in case of operation of these commands,  
wraparound occurs. For example page 100  
appears to be one greater than page 199.  
For further information ask your dealer. See  
also the booklet supplied with your decoder.  
Connect a decoder with an aerial socket  
to the TV  
• Connect the aerial cable.  
ENGLISH - 22 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connect a decoder without an aerial  
socket to the TV  
Camera And Camcorder to  
Connect to FAV Input  
• Connect the decoder to the TV with a  
eurocable to Scart 1.  
Connect your camera or camcorder FAV input  
at the right side of the TV.  
TV And Video Recorder  
• Connect your equipment to the TV via VIDEO  
(yellow), AUDIO R (red) and AUDIO L (white)  
inputs. You should connect the jacks to the  
input in the same color.  
• Connect the aerial cables.  
Better picture quality can be obtained if you  
also connect a eurocable to SCART sockets.  
To Connect to SVideo Input  
Playback NTSC  
Connect your camera or camcorder SVideo  
input at the right side of the TV.  
To use this option you can;  
• Connect NTSC VCR player to Euroconnec-  
tor at the rear side of the TV.  
• Connect your equipment to the TV via SVideo  
input and audio inputs of FAV inputs by using  
SVideo cables.  
• Connect NTSC VCR player to RCA Jacks at  
the right side of the TV.  
Connect The Decoder To The  
Video Recorder  
Then, press “AV” button to select proper  
source.  
Some video recorders have a special euro-  
connector for decoder.  
Copy Facility  
Source selection for VCR recording.  
• Select options menu.  
• Connect a eurocable to the euroconnector of  
your decoder and to the special eurocon-  
nector of your video recorder. See also the  
booklet of your video recorder.  
• Select scart 2 out source pressing “ “ /  
“
” button.  
• To connect your video recorder to the TV, see  
TV and Video Recorder section.  
• Select Scart 1 to copy the picture from tuner.  
• Select Scart 2 to copy the picture from Tuner,  
FAV or Scart 1.  
If you want to connect more equipment to your  
TV, consult your dealer.  
Search For And Store The Test  
Signal Of The Video Recorder  
Connecting Headphones  
Use the stereo headphone socket at the right  
side of the TV, to connect headphones.  
• Unplug the aerial cable from the aerial socket  
“ANT” of your video recorder.  
You can adjust the headphones volume and  
sound mode from the audio menu. See page  
14 for details.  
• Switch on your TV and put the video recorder  
on the test signal. (See the booklet for your  
video recorder.)  
• Enter the tv tuner menu in settings menu.  
Enter the programming menu in tv tuner  
menu and select manual search.  
• Search for the test signal of your video re-  
corder in the same way as you searched for  
and stored the TV signals. See program-  
ming menu. Store the test signal under  
programme number 0.  
• Replace the aerial cable in the aerial socket  
“ANT” of your video recorder once you have  
stored the test signal.  
ENGLISH - 23 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AntennaConnections  
ConnectPeripheralEquipment  
HEADPHONE  
AUDIO  
VIDEO  
&$0&25'(5  
FORSATELLITERECEIVER  
DECODER  
ENGLISH - 24 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PCInputTypical Display Modes  
The display has a maximum resolution of 1280 x 768, vertical sync. frequency range of 50-75 Hz  
and a horizontal sync. frequency range of 30-69 KHz.  
The following table is an illustration of some of the typical video display modes.  
5HVROXWLRQ  
)UHTXHQF\ꢁ  
0RGH  
+RUL]RQWDO 9HUWLFDO +RUꢀꢁꢂN+]ꢃ 9HUꢀꢁꢂ+]ꢃ  
ꢀ
ꢇ
ꢄ
ꢂ
ꢆ
ꢁ
ꢉ
ꢈ
ꢊ
ꢁꢂꢃ  
ꢁꢂꢃ  
ꢁꢂꢃ  
ꢉꢇꢃ  
ꢈꢃꢃ  
ꢈꢃꢃ  
ꢈꢃꢃ  
ꢀꢃꢇꢂ  
ꢀꢃꢇꢂ  
ꢀꢃꢇꢂ  
ꢀꢇꢈꢃ  
ꢂꢃꢃ  
ꢂꢈꢃ  
ꢂꢈꢃ  
ꢂꢃꢃ  
ꢁꢃꢃ  
ꢁꢃꢃ  
ꢁꢃꢃ  
ꢉꢁꢈ  
ꢉꢁꢈ  
ꢉꢁꢈ  
ꢉꢁꢈ  
ꢄꢀꢅꢆ  
ꢄꢉꢅꢊ  
ꢄꢉꢅꢆ  
ꢄꢀꢅꢆ  
ꢄꢉꢅꢊ  
ꢂꢈꢅꢀ  
ꢂꢁꢅꢊ  
ꢂꢈꢅꢂ  
ꢆꢁꢅꢆ  
ꢁꢃꢅꢃ  
ꢂꢉꢋꢁ  
ꢁꢃ  
ꢉꢇ  
ꢉꢆ  
ꢉꢃ  
ꢁꢃ  
ꢉꢇ  
ꢉꢆ  
ꢁꢃ  
ꢉꢃ  
ꢉꢆ  
ꢁꢃ  
ꢀꢃ  
ꢀꢀ  
The native resolution of the TFT-LCD Panel is 1024 x 768. Therefore using Mode 10 is advised  
to get the best PC input display quality.  
PIPCombinationRestrictions  
ꢀꢀꢀꢀꢀꢀꢀHhv  
QDQ  
T86SUꢀ ꢀ T86SUꢀ!ꢀ  
UVI@S T86SUꢀ  T86SUꢀ!  
A6W  
Q8  
TꢁWD9@P  
SB7  
SB7  
UVI@S  
T86SUꢀ  
T86SUꢀ!  
T86SUꢀ ꢀ  
SB7  
T86SUꢀ!ꢀ  
SB7  
A6W  
Q8  
TꢁWD9@P  
Uuv†ꢀp‚qv‡v‚ꢀv†ꢀ‚‡ꢀƒ‚††viyr  
ENGLISH - 25 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control  
Tips  
Your TV no longer responds to the remote con-  
trol. Perhaps the batteries are exhausted.  
Replace the batteries.  
Care Of The Screen  
Clean the screen with a slightly damp, soft  
cloth. Do not use abrasive solvents as they  
may damage the TV screen coating layer.  
Have you selected the wrong menu? Press  
“BACK” button to return to TV mode or press  
“MENU” button to return to the previous menu.  
Poor Picture  
No solution  
Have you selected the correct TV system? Is  
your TV set or house aerial located too close  
to the loudspeakers, non-earthed audio equip-  
ment or neon lights, etc.?  
Switch your TV set off and on. If this does not  
work, call the service personnel; never attempt  
to repair it yourself.  
Mountains or high buildings can cause double  
pictures or ghost images. Sometimes you can  
improve the picture quality by changing the  
direction of the aerial.  
Is the picture or Teletext unrecognisable?  
Check if you have entered the correct frequency.  
The picture quality may degrade when two  
peripherals are connected to the TV at the  
same time. In such a case, disconnect one of  
the peripherals.  
For users in the UK:  
If you have any problems setting up your  
new TV, please call the  
on 0870330 5000  
Helpline  
No Picture  
For users in the Republic of Ireland:  
Is the aerial connected properly? Are the plugs  
connected tightly to the aerial socket? Is the  
aerial cable damaged? Are suitable plugs  
used to connect the aerial? If you are in doubt,  
consult your dealer.  
If you have any problems setting up your  
new TV, please call the  
on 1890 - 582500  
Helpline  
No Picture means that your TV is not receiv-  
ing any transmission. Have you pressed the  
correct buttons on the remote control? Try once  
more.  
PC Picture  
If no PC picture appears, check the D-SUB  
cable is connected properly. Check that your  
PC's resolution set correctly. See page 25 for  
supported modes.  
Sound  
You can not hear any sound. Did you perhaps  
interrupt the sound, pressing “ ” button? Are  
external speakers connected to the TV?  
Sound is coming from only one of the speak-  
ers. Is the balance set to one direction ex-  
treme? See audio menu.  
ENGLISH - 26 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Model  
Item  
LT-30E45SJ  
Broadcasting Systems  
Channels and  
Frequencies  
PAL SECAM, B/G, D/K, I/I', L/L'  
VHF (VL) 46,25 MHz - 168,25 MHz  
VHF (VH) 175,25 MHz - 463,25 MHz  
UHF  
471,25 MHz - 863,25 MHz  
Cable TV (S1-S20/ S21-S41)  
Input Signal  
Video: Analog 0,7 Vp-p 75 ohm positive  
Sync: TTL Level positive or negative, Seperate sync.  
30 - 69 KHz  
Horizontal Timing  
Vertical Timing  
50 - 75 Khz  
Dot Rate  
78,75 MHz max.  
Panel Size  
29,5” (measured diagonally)  
Visible Picture Size  
Display Resolution  
Number of Preset Channels  
Channel Indicator  
RF Aerial Output  
Power Requirements  
Power Consumption (W)  
Sound Systems  
Audio Output  
643 mm horizontal x 386 mm vertical  
1280 x 768 max. (WXGA)  
100  
On Screen Display (OSD)  
75 Ohm (unbalanced)  
220-240 V AC, 50 Hz  
150 W (max) / STAND-BY <4W  
German , Nicam Stereo  
2 x 8 WRMS. (%10 THD)  
EXT-1Terminal  
Euroconnector (21-pin, SCART 1) (bottom of the cabinet)  
• Video Input, Audio L/R Inputs and RGB inputs are available.  
• TV broadcast outputs (Video and Audio L/R) are available.  
Euroconnector (21-pin, SCART 2) (bottom of the cabinet)  
EXT-2Terminal  
EXT-3Terminal  
• Video Input, S-VIDEO (Y/C) input, Audio L/R and RGB inputs are available.  
• Video and Audio L/R outputs are available.  
• T-V LINK functions are available.  
RCA connectors x 3 (side of the cabinet)  
S-VIDEO connector x 1 (side of the cabinet)  
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.  
RCA connectors x 2 (bottom of the cabinet)  
• Audio L-R Line Outs are available  
Audio Output  
PC IN terminal  
Analog RGB D-SUB 15 x 1  
• PC signal is available (refer to page 25 for details of the signals which can be input)  
Stereo mini-jack (3.5 mm diameter)  
PC AUDIO IN terminal  
Dimensions (W x H x D)  
847 mm x 522 mm x 260 mm  
847 mm x 490 mm x 102 mm (TV only)  
14.8 kg (with stand) / 13 kg (TV only)  
Weight  
Accessories  
Remote control unit x 1 (RM-C1860) / AA/R6 dry cell battery x 2  
Power cord x 1  
Headphone jack  
Stereo mini-jack (3.5 mm diameter)  
ENGLISH - 27 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ENGLISH  
DEUTSCH  
FRANÇAIS  
ITALIANO  
LT-30E45SU  
WIDE LCD PANEL TV  
INSTRUCTIONS  
BEDIENUNGSANLEITUNG  
BREITBILD-LCD-TV  
TÉLÉVISEUR À GRAND ÉCRAN LCD  
TV A PIENO SCHERMO LCD  
MANUEL D'INSTRUCTIONS  
ISTRUZIONI  
50059494  
©2004 VICTOR COMPANY OF JAPAN, LIMITED  
1004MKH-VT-VT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
How to remove the stand ........................ 2  
Important Information ............................. 3  
TV Control Buttons and Terminals ......... 4  
Remote Control Buttons.......................... 6  
Preparation .............................................. 7  
Safety Precautions.................................. 7  
Before Switching On Your TV ................. 9  
Switching The TV ON/OFF ....................... 9  
Operating The TV................................... 10  
Other Features....................................... 18  
Teletext................................................... 21  
Connect Peripheral Equipment ............ 22  
Antenna Connections ............................ 24  
PC Input Typical Display Modes ............ 25  
PIP Combination Restrictions............... 25  
Tips ......................................................... 26  
Specifications ........................................ 27  
ENGLISH - 1 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
• Do not allow children to hang from the TV, place their elbows  
on the TV or lean against the TV. Doing so may cause the TV to  
fall over and lead to injuries.  
CAUTION:  
• The TV screen may be damaged if the TV is carried as shown  
in the diagram below.  
The TV should always be carried by two people.  
How to remove the stand  
ENGLISH - 2 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Information  
Please take note  
EXCLUSION CLAUSE  
JVC shall under no circumstances be liable for loss and/or damage to the product caused  
by:  
• fire;  
• earthquake;  
• accidental damage;  
• intentional misuse of the product;  
• use of the product in improper conditions;  
• loss and/or damage caused to the product whilst in the possession of a third party;  
• any damage or loss caused as a result of the owner’ s failure and/or neglect to follow the  
instructions set out in the owner’s manual;  
• any loss or damage caused directly as a result of misuse or malfunction of the product  
when used simultaneously with associated equipment;  
Furthermore, under no circumstances shall JVC be liable for any consequential loss and/  
or damage including but not limited to the following, loss of profit, interruption of business,  
the loss of recorded data whether caused during normal operation or misuse of the  
product.  
WARNING! NEVER LEAVEA  
Care and disposal  
STATIONARY IMAGE ON THE  
SCREEN  
Cleaning the screen and cabinet...  
If stationary images generated by TELETEXT,  
CHANNELIDENTIFICATION LOGOS, COM-  
PUTER DISPLAYS, VIDEO GAMES, ON  
SCREEN MENUS, etc. are left on the TV  
screen for any length of time, they could be-  
come permanently ingrained.  
Turn off the power, clean the screen and cabi-  
net with a soft, dry cloth. We recommend that  
you do not use any proprietary polishes or  
solvents on the screen or cabinet as this may  
cause damage.  
If you use your television to display completely  
still images, or moving pictures which have a  
permanent still image superimposed e.g.  
broadcast network logos, it is always advis-  
able to reduce BOTH the brightness and con-  
trast settings.  
Disposal...  
When the set reaches the end of its useful  
life please dispose of it in accordance with  
Local Government Regulations or at a recy-  
cling centre.  
ENGLISH - 3 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV Control Buttons and Terminals  
FRONT VIEW  
REAR VIEW  
ENGLISH - 4 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Headphone  
Audio Input (Left, Right)  
Video Input  
S-VHS Input  
FrontAV  
STAND BY button  
TV/AV button  
MENU button  
Program Up, Program Down buttons  
Volume Up, Volume Down buttons  
Power cord input  
On/Off switch  
Antenna  
Audio Line Out L, R  
Scart 1  
Scart 2  
Audio In (for PC)  
PC Input  
TV Control Buttons  
ENGLISH - 5 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Buttons  
ꢀ
ꢁ
ꢁꢂ  
/ I = (Stand By) button  
TV / VCR / DVD Switch  
Number buttons  
AV button (Tuner, Scart 1, Scart 1 RGB,  
Scart 2, Scart 2 RGB, PC, FAV, SVideo)  
ꢂ
BLUE / PICTURE Mode button  
YELLOW /  
Sleep Timer button  
MENU button  
ꢁꢁ  
ꢁꢀ  
ꢁꢆ  
$9  
ꢃ
ꢉ
= Cursor Up button  
OK button  
ꢇ
ꢄ
= Cursor Right button  
BACK button  
ꢀꢅ  
ꢈ
= Volume + / - buttons  
Teletext / VCR / DVD Control buttons  
PIP Control Buttons  
ꢅ
ꢀꢈ  
ꢀꢆ  
ꢀꢀ  
ꢀꢄ  
ꢀꢇ  
P
buttons  
= Cursor Down button  
= Teletext Button  
ꢀꢉ  
ꢀꢁ  
= Cursor Left button  
= Stereo / Bilingual button  
3
GREEN /  
Hyper Sound On/Off button  
RED / ZOOM Mode button  
= Information Button  
= Mute button  
ꢀꢂ  
ꢀꢃ  
79  
ENGLISH - 6 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Stereo PC Audio Input  
• 4H Comb Filter  
Preparation  
For ventilation, leave a space of at least 10 cm  
free all around the set. To prevent any fault  
and unsafe situations, please do not place  
any objects on top of the set.  
• Audio Line Out  
Panel Features  
• High resolution, 30-inch TFT LCD display.  
• WXGA resolution (1280 x 768)  
• Contrast ratio (600:1 typical)  
Use this apparatus in tropical and/or moder-  
ate climates.  
Features  
• Brightness (typical) 550 cd/m2.  
• It is a remote controlled color television.  
• Response time (typical) 25 msec.  
• 100 programmes from VHF, UHF bands or  
cable channels can be preset.  
• Viewing angle (typical) 170° (horizontal) and  
170° (vertical).  
• It can tune cable channels.  
• Display color 16.7 Million.  
• Controlling the TV is very easy by its menu  
driven system.  
Safety Precautions  
1. Power Source  
• It has 2 Euroconnector sockets for external  
devices (such as video, video games, audio  
set, etc.)  
The receiver should be operated only from a  
220 - 240 V AC, 50 Hz. outlet. Ensure you se-  
lect the correct voltage setting for your conve-  
nience.  
• Stereo sound system (German+Nicam).  
• Full function Teletext .  
Fastext (10 Pages), TOP text.  
• It is possible to connect headphone.  
• Direct channel access.  
2. Power Cord  
The power supply cord should be placed so  
that it is not likely to be walked on or pinched  
by items placed upon them or against it. Pay  
particular attention to cord where it enters the  
plug, power outlet, and the point where it exits  
from the receiver.  
• A.P.S. (Automatic Programming System).  
• All programmes can be named.  
• Sleep timer.  
• Automatic sound mute when no transmis-  
sion.  
3. Moisture and Water  
• Auto, Full, 16:9 Zoom,16:9 Zoom Subtitle,  
Regular, Panoramic, 14:9 Zoom modes.  
Auto switch WSS (Wide Screen Signaling).  
Do not use this equipment in a humid and  
damp place (avoid the bathroom, the sink in  
the kitchen, and near the washing machine).  
Do not expose this equipment to rain or water,  
as this may be dangerous and do not place  
objects filled with liquids on top. Avoid from  
dripping or splashing.  
• NTSC Playback.  
• Front SVHS is available.  
• Front AV in is available.  
• It has VGA connector for external devices such  
as computer.  
4. Cleaning  
• It has PIP functions.  
• TV Picture in PC  
Before cleaning, unplug the receiver from the  
main supply, outlet. Do not use liquid or aero-  
sol cleaners. Use soft and dry cloth.  
• When no valid signal is detected, after 5 min-  
utes the TV switches itself automatically to  
stand-by mode.  
5. Ventilation  
The slots and openings on the receiver are  
intended for ventilation and to ensure reliable  
operation. To prevent overheating, these open-  
• PC input (Support Up to WXGA 1280 x 768)  
• 1 SVHS Input and 1 RCA AV Input are avail-  
able.  
ENGLISH - 7 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ings must not be blocked or covered in any-  
way.  
6. Lightning  
In case of storm and lightning or when going  
on holiday, disconnect the power cord from  
the wall outlet.  
7. Replacement Part  
When replacement parts are required, be sure  
the service technician has used replacement  
parts which are specified by the manufacturer or  
have the same specifications as the original one.  
Unauthorised substitutions may result in fire,  
electrical shock, or other hazards.  
8. Servicing  
Please refer all servicing to qualified person-  
nel. Do not remove cover as this may result in  
electric shock.  
9. Naked Flame Sources  
Do not place naked flame sources on the ap-  
paratus.  
WARNING: When the device is not in use for  
a long time, disconnect from power.  
"The LCD panel is very high technology prod-  
uct with about a million thin film transistors,  
giving you fine picture details. Occasionally,  
a few non-active pixels may appear on the  
screen as a fixed point of blue, green or red.  
Please note that this does not affect the per-  
formance of your product."  
Instructions for waste disposal:  
• Packaging and packaging aids are recy-  
clable and should principally be recycled.  
Packaging materials, such as foil bag, must  
be kept away from children.  
• Battery, including those which is heavy metal-  
free, should not be disposed of with house-  
hold waste. Please dispose of used battery  
in an environmentally sound manner. Find  
out about the legal regulations which apply  
in your area.  
“DO NOT LEAVEYOUR TVAT STAND-BYOR  
OPERATING WHEN YOU LEAVE YOUR  
HOUSE”  
• Cold cathode fluoresant lamp in LCD PANEL  
contains a small amount of mercury, please  
follow local ordinates or regulations for dis-  
posal.  
ENGLISH - 8 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Switching OnYour TV  
Power Connection  
IMPORTANT: The TV set is designed to oper-  
ate on 220 - 240 V AC, 50 Hz.  
• After unpacking, allow the TV set to reach the  
ambient room temperature before you con-  
nect the set to the mains.  
Connections To The RF Input  
Socket  
NOTE: Remove batteries from remote con-  
trol handset when it is not to be used for a long  
period.Otherwise it can be damaged due to  
any leakage of batteries.  
• Connect the aerial or cable TV plug to the RF  
input socket located at the back of the TV  
and connect the cable plug coming out from  
the TV out socket located at the devices (VCR,  
DVB etc.) to this socket as well.  
Switching The TV ON/OFF  
To switch the TV on:  
Your TV will switch on in two steps:  
1- Connect the power supply cord to the sys-  
tem. Press On/Off switch at the rear of the  
TV. Then the TV switches itself to stand-by  
mode and the power lamp becomes red lo-  
cated on the front of the TV.  
2- To switch on the TV from stand-by mode  
either:  
Press a digit button on the remote control so  
that a programme number is selected,  
How To Connect Other Devices  
or,  
IMPORTANT: Switch off the TV before connect-  
ing any external device.  
Press “ / I”, "-P/CH" or "P/CH+" button at the  
top of the TV or press “  
” or “  
” button  
Sockets for external connections are at the  
back and side of the TV. For connection of other  
devices via Euroconnector refer to the manu-  
als of the related devices.  
on the remote control, so that last switched off  
programme is selected.  
By either ways the TV will switch on and the  
power lamp becomes green.  
Inserting Batteries In The Remote  
Control Handset  
To switch the TV off:  
• Press the “stand-by” button on the remote  
control, so the TV will switch to stand-by  
mode and the power lamp will become RED,  
• Place the batteries in the right directions as  
seen below.  
• Remove the battery cover located on the back  
of the handset by gently pulling upwards from  
the indicated part.  
or,  
Press the “ / I” button located on the top of  
the TV, so the TV will switch off and the power  
lamp will become RED.  
• Insert two AA/R6 dry cell or equivalent type  
of batteries inside.  
To switch the TV off completely press On/Off  
switch at the rear of the TV and remove the  
mains plug from the socket.  
• Replace the battery cover.  
ENGLISH - 9 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Volume Setting  
Operating The TV  
Press “VOLUME -” button to decrease volume  
or “VOLUME +” button to increase volume, so  
a volume level scale (slider) will be displayed  
at the middle of the bottom on the screen.  
You can operate your TV both using the re-  
mote control handset and onset buttons.  
Initial APS (Automatic Programming  
System)  
The following menu will be displayed on the  
screen when you turn on your TV for the first  
time. APS, searches and sorts all channels  
and stores them automatically on your TV, ac-  
cording to the transmission of programme  
systems in your area.  
Programme Selecting  
Press “P/CH+” button to select the next  
programme or “PCH-” button to select the pre-  
vious programme.  
“P/CH+ / PCH-” and “VOLUME + / VOLUME -”  
buttons on the TV are used as navigation but-  
tons in menu.  
Entering The Menu  
Press “MENU” button at the control panel on  
the top of the TV to enter the menu.  
“P/CH+ / PCH-” and “VOLUME + / VOLUME -”  
buttons at the control panel on the top of the  
TV work as direction buttons in the menu.  
To cancel APS before starting, press “BACK”  
button.  
EXT Mode  
First of all choose language and country by  
Press “TV/AV” button at the control panel on  
the top of the TV to switch your TV to EXT mode  
(See EXT Modes in page 20).  
using “ “ / “ ” and “ “ / “ ” buttons. This,  
will effect the sort process in APS. To start aps  
select autoset, by using “ “ / “ ” buttons  
Operating With Remote Control  
and press “ “ / “ ” or “OK” button. WhileAPS  
is running, no picture appears.  
The remote control handset of your TV is de-  
signed to control all the functions of the model  
you selected. The functions will be described  
in accordance with the menu system of your  
TV.  
Functions of the menu system are described  
in Menu System section.  
AfterAPS is finalized, the programme table will  
be appeared on the screen. In the programme  
table you will see the programme numbers  
and names assigned to the programmes.  
Volume Setting  
Press “  
+” button to increase volume.  
If you do not accept the locations and / or the  
programme names of programmes, you can  
change them in aps submenu in the settings  
menu. (See page 17 for Program table expla-  
nation.)  
Press “-  
” button to decrease volume.  
A volume level bar will be displayed at the  
middle of the bottom on the screen.  
Operating with the buttons on the  
TV set  
Volume setting and programme selection can  
be made by using the buttons at the control  
panel on the top of the TV.  
ENGLISH - 10 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programme Selecting (Previous or next  
programme)  
ton. One programme is displayed on the whole  
screen at this option.  
pip  
• Press “  
” button to select the previous  
programme.  
By pressing “ “ / “ ” button, select pip.  
“<ok> activates pip window layout” is seen  
• Press “  
” button to select the next  
programme.  
on the screen. Press “ ” or “OK” button. The  
first programme can be watched on the back-  
ground. The second programme is seen at  
the pip window.  
Programme Selecting (direct access):  
Press digit buttons on the remote control hand-  
set to select programmes between 0 and 9.  
TV will switch to the selected program after a  
short delay.  
PIP picture is displayed on the screen also  
with “  
Programme in the PIP window is increased /  
decreased by “ ” , digit buttons or  
AV button when PIP window is selected. PIP  
” button.  
• For a two digit program number enter the  
second digit after pressing the first digit within  
2 seconds.  
/
Menu System  
window is removed from the screen by “  
button.  
”
Your TV has been designed with a menu sys-  
tem to provide an easy manipulation of a mul-  
tifunction system. Press the “MENU” button to  
enter the menu.  
picture menu  
By pressing “ “ / “ ” button, select the sec-  
ond icon. Picture menu appears on the screen.  
Press “ “ / “ ” button to select a menu title  
and then “ “ / “ ” button to select a menu  
item and “ “ / “ ” or “OK” button to enter the  
submenu. Press “MENU” button to return to  
the previous menu. Press “BACK” button to  
exit from the menu.  
layout menu  
By pressing “ “ / “ ” button, select the first  
icon. Layout menu appears on the screen.  
brightness  
By pressing “ “ / “ ” button, select bright-  
ness. “right/left to adjust brightness” is seen  
on the screen. Press “ ” button to increase  
brightness. Press “ “ button to decrease  
brightness. Brightness level can be adjusted  
between 0 and 100.  
contrast  
By pressing “ “ / “ ” button, select contrast.  
“right/left to adjust contrast” is seen on the  
full screen  
screen. Press “ ” button to increase contrast.  
By pressing “ “ / “ ” button, select full  
screen. “<ok> activates one window layout”  
Press “ “ button to decrease contrast. Con-  
trast level can be adjusted between 0 and 100.  
is seen on the screen. Press “ ” or “OK” but-  
ENGLISH - 11 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
sharpness  
brightness  
By pressing “ “ / “ ” button, select sharp-  
ness. “right/left to change sharpness” is seen  
By pressing “ “ / “ ” button, select bright-  
ness. “right/left to adjust brightness” is seen  
on the screen. Press “ ” button to increase  
on the screen. Press “ ” button to increase  
sharpness. Press “ “ button to decrease  
sharpness. Sharpness level can be adjusted  
between 0 and 8.  
brightness. Press “ “ button to decrease  
brightness. Brightness level can be adjusted  
between 0 and 100.  
color  
contrast  
By pressing “ “ / “ ” button, select color.  
“right/left to adjust color” is seen on the  
By pressing “ “ / “ ” button, select contrast.  
“right/left to adjust contrast” is seen on the  
screen. Press “ ” button to increase color.  
screen. Press “ ” button to increase contrast.  
Press “ “ button to decrease color. Color level  
can be adjusted between 0 and 100.  
Press “ “ button to decrease contrast. Con-  
trast level can be adjusted between 0 and 100.  
tint  
phase  
This item is displayed in picture menu when  
TV is in AV mode and at NTSC signal. By  
pressing “ “ / “ ” button, select tint. "right/  
left to adjust tint" is seen on the screen. Press  
By pressing “ “ / “ ” button, select phase.  
"right/left to adjust phase" is seen on the  
screen. Press “ ” button to increase phase.  
Press “ “ button to decrease phase. Phase  
level can be adjusted between 0 and 100.  
“ ” button to increase tint. Press “ “ button  
to decrease tint. Tint level can be adjusted be-  
tween 0 and 100.  
window menu  
By pressing “ “ / “ ” button, select the third  
icon. Window menu appears on the screen.  
• If full screen option was selected at the lay-  
out menu, the window menu is seen as be-  
low.  
When TV is in AV mode; picture menu items  
(brightness, contrast, sharpness and color)  
may require re-adjustment.  
When PC is Connected To TV:  
image size  
By pressing “ “ / “ ” button, select image  
size. "right/left to change image size" is seen  
on the screen. By pressing “ “ / “ ” button,  
you can change image size to Auto, Full, 16:9  
Zoom, 16:9 Zoom Subtitle, Regular, Pan-  
oramic, 14:9 Zoom modes.  
You can enter image size directly by pressing  
“ZOOM” button.  
ENGLISH - 12 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• If pip option was selected, the window menu  
is seen as below.  
When PC Is Connected To TV  
image size  
By pressing “ “ / “ ” button, select image  
size. "right/left to change image size" is seen  
image size  
on the screen. By pressing “ “ / “ ” button,  
you can change image size to Fill all, Fill 1:1  
and Fill aspect.  
By pressing “ “ / “ ” button, select image  
size. "right/left to change image size" is seen  
on the screen. By pressing “ ” / “ ” button,  
you can change image size to full, regular and  
auto.  
h position  
By pressing “ “ / “ ” button, select h posi-  
tion. "right/left to adjust h position" is seen  
You can enter image size directly by pressing  
“ZOOM” button. See Page 20 for details.  
on the screen. Press “ ” button to slide the  
pip size  
screen to the left. Press “ “ button to slide  
screen to the right. h position can be adjusted  
between 0 and 100.  
By pressing “ “ / “ ” button, select pip size.  
"right/left to adjust PIP size" is seen on the  
v position  
screen. Press “ ” button to increase pip size.  
By pressing “ “ / “ ” button, select v posi-  
tion. "right/left to adjust v position" is seen  
Press “ “ button to decrease pip size. Pip  
size can be adjusted between 0 and 100.  
on the screen. Press “ ” button to slide the  
When PIP is activated you can enter the pip  
screen to up. Press “ “ button to slide screen  
to down. v position can be adjusted between  
0 and 100.  
size directly by pressing “  
” button.  
pip position  
By pressing “ “ / “ ” button, select pip posi-  
tion. "right/left to adjust PIP position" is  
audio menu  
By pressing “ “ / “ ” button, select the fourth  
icon. Audio menu appears on the screen.  
seen on the screen. By pressing “ “ / “ ”  
button, you can change the pip position as left  
top, right top, middle, left bottom or right bot-  
tom (as seen on the menu above).  
When PIP is activated you can change pip po-  
sition directly by pressing "  
" button.  
ENGLISH - 13 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
volume  
“MENU” button to exit the equalizer menu.  
By pressing “ “ / “ ” button, select volume.  
"right/left to adjust volume" is seen on the  
screen. Press “ ” button to increase volume  
level. Press “ “ button to decrease volume  
level. Volume level can be adjusted between  
0 and 63.  
hyper sound  
hp volume  
It is used to gain saloon effect to the sound.  
By pressing “ “ / “ ” button, select hp vol-  
ume. "right/left to adjust hp volume" is seen  
By pressing “ “ / “ ” button, select hyper  
sound. "right/left for wide sound off/stereo/  
mono" is seen on the screen. By pressing  
on the screen. Press “ ” button to increase  
headphone volume level. Press “ “ button to  
decrease headphone volume level. Hp vol-  
ume (headphone volume) level can be ad-  
justed between 0 and 100.  
“ “ / “ ” button set to hyper sound on to  
activate it or off to deactivate it.  
dynamic bass  
hp sound mode  
Dynamic Bass is used to increase bass ef-  
fect of the TV set.  
By pressing “ “ / “ ” button, select hp sound  
mode. "right to adjust hp sound mode" is  
By pressing “ “ / “ ” button, select dynamic  
bass. "right/left for dynamic bass on/off" is  
seen on the screen. Press “ “ / “ ” button  
change hp sound mode.  
seen on the screen. By pressing “ “ / “ ”  
button set to dynamic bass on to activate it or  
off to deactivate it.  
Hp sound mode is used to identify sound mode  
of the headphone. hp sound mode can be set to  
mono, stereo, dual a or dual b according to the  
transmission.  
options menu  
By pressing “ “ / “ ” button, select the fifth  
icon. Options menu appears on the screen.  
balance  
By pressing “ “ / “ ” button, select balance.  
"right/left to adjust balance" is seen on the  
screen. Press “ ” button to increase balance  
rightward. Press “ “ button to decrease bal-  
ance leftward. Balance level can be adjusted  
between -50 and 50.  
equalizer  
By pressing “ “ / “ ” button, select equal-  
izer. "right/left for equalizer settings" is seen  
on the screen. Press “ “ / “ ” or “OK” button  
to enter equalizer menu. In equalizer menu  
the sound mode can be changed to user, flat,  
language  
pop, rock, jazz and classic by pressing “ “ /  
By pressing “ “ / “ ” button, select lan-  
guage. "right/left to change language" is  
“ ” button. Equalizer menu settings can be  
changed only when sound mode is user. Se-  
lect the desired frequency by “ “ / “ ” button  
and increase or decrease the frequency gain  
seen on the screen. By pressing “ “ / “ ”  
button, you can select the language.  
by pressing “ “ / “ ” button.  
ENGLISH - 14 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
vcr  
scart 2 out  
This item is displayed only when TV is in AV  
mode. By pressing “ “ / “ ” button, select  
vcr. "right/left to change vcr status" is seen  
By pressing “ “ / “ ” button, select scart 2  
out. "right/left to select scart 2 out" is seen on  
the screen. You can set scart 2 out to Scart 1,  
on the screen. By pressing “ “ / “ ” button  
tuner or FAV by pressing “ “ / “ ” button.  
set vcr to on or off.  
sleep timer  
By pressing “ “ / “ ” button, select sleep  
timer. "adjust sleeptimer" is seen on the  
screen. The Sleep Timer is used to turn the  
TV off after a defined period of time after se-  
lecting this item. The timer can be pro-  
grammed between 0 and 120 minutes in  
steps of 10 minutes. (0, 10, 20, 30, 40, ... ,  
120)  
If sleep timer is activated, at the end of the  
selected the time, the TV goes automatically  
to stand-by mode.  
settings menu  
osd timeout  
By pressing “ “ / “ ” button, select the sixth  
icon. Settings menu appears on the screen.  
By pressing “ “ / “ ” button, select osd  
timeout. "right/left to change osd timeout"  
• If full screen option was selected at the lay-  
out menu, the settings menu is seen as be-  
low.  
is seen on the screen. By pressing “ “ / “ ”  
button, you can change osd timeout to 5 sec,  
15 sec or 60 sec.  
menu background  
By pressing “ “ / “ ” button, select menu  
background. "right to change menu back-  
ground" is seen on the screen. You can  
change menu background to translucent or  
opaque by pressing “ ” button.  
If pip option was selected at the layout menu  
or in AV mode, the settings menu is seen as  
below.  
child lock  
You can use this feature to prevent children  
turning on TV or changing programs or ad-  
justments etc. without remote control.  
By pressing “ “ / “ ” button, select child  
lock. "right/left to change" is seen on the  
screen. The child lock feature can be set by  
“ “ / “ ” button to either on or off. When off is  
selected, there will be no difference in the op-  
eration of your TV. When on is selected, the TV  
can only be controlled by the remote control  
handset.  
tv tuner  
By pressing “ “ / “ ” button, select tv tuner.  
"OK to activate tuner menu" is seen on the  
screen. By pressing “ “ / “ ” or “OK” button  
ENGLISH - 15 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
enter the menu. tv tuner menu has two sub-  
menu named as aps and programming.  
standard  
By pressing “ “ / “ ” button, select stan-  
dard. “right/left to change standard” is seen  
programming menu  
on the screen. By pressing “ “ or “ ” button,  
you can change the standard to B/G, D/K, I or  
L/L'.  
By pressing “ “ / “ ” button in tv tuner menu  
select the first icon. Programming menu ap-  
pears on the screen.  
channel type  
By pressing “ “ / “ ” button, select channel  
type. "right/left to change channel type" is  
seen on the screen. By pressing “ “ or “ ”  
button, you can change the channel type to C  
or S.  
edit labels  
By pressing “ “ / “ ” button, select edit la-  
bels. "right/left to edit labels" is seen on the  
screen. By pressing “ “ / “ ” or “OK” button,  
you can enter the following menu.  
program  
By pressing “ “ / “ ” button, select program.  
"right/left to select program" is seen on the  
screen. By pressing “ “ or “ ” button, you  
can select the program number. You can also  
enter a number via digit buttons on the remote  
control. There are 100 program storage be-  
tween 0 and 99.  
“
“ / “ ” or “ “ / “ ” buttons are used to  
edit labels.  
store program  
By pressing “ “ / “ ” button, select store  
program. "right/left to store program" is  
fine tune  
By pressing “ “ / “ ” button, select fine tune.  
"right/left to adjust fine tuning" is seen on  
seen on the screen. By pressing “ “ / “ ” or  
“OK” button, you can store the program and  
following menu appears on the screen.  
the screen. By pressing “ “ or “ ” button, you  
can adjust the tuning. The adjust values are  
between -50 and +50.  
channel  
By pressing “ “ / “ ” button, select channel.  
"right/left to change channel" is seen on the  
manual search  
screen. By pressing “ “ or “ ” button, you  
can change the channel number. You can also  
enter a number via digit buttons on the remote  
control. The adjust values change according  
to the standard and channel type.  
By pressing “ “ / “ ” button, select manual  
search. "right/left to search" is seen on the  
screen. By pressing “ “ or “ ” button, you  
can start program searching and following  
menu appears on the screen.  
ENGLISH - 16 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
In program table, “ “ / “ ” buttons work like  
"Direction Up" and "Direction Down". By cur-  
sor action, programme selection is done au-  
tomatically.  
Programme Number is between 01 and 99.  
00 is not displayed on program table.  
Programme Name has a name string with 5  
characters. After autoset process the  
Programme Names are set to "C02" or "S07"  
(channel type and channel number) or name  
of the tuned channel if defined.  
aps menu  
By pressing “ “ / “ ”” button in tv tuner menu  
select the second icon. aps menu appears  
on the screen.  
At the bottom of the program table there is a  
programme sort functions section. Each func-  
tion is activated by color button (seen above).  
By Delete you can delete programmes that  
you decided. Insert section is for inserting  
programmes into another programme  
spaces. Name allows changing the  
programme name.  
Delete:  
For "Delete" process RED button is pressed.  
The following warning menu comes to screen.  
Pressing “MENU” button cancels the activated  
"Delete" process. Pressing “OK” button  
erases the selected programme from the  
programme list, and the programmes below  
shift one up.  
program table  
By pressing “ “ / “ ” button, select program  
table. "right/left to enter program table" is  
seen on the screen. By pressing “ “ / “ ” or  
“OK” button, you can enter the following pro-  
gram table.  
• Program table may be entered only when the  
layout is full screen. You can not enter to  
program table when layout is pip screen.  
ꢀ0(18!  
ꢀ2.!  
Insert:  
Select the program which you want to insert  
by navigation buttons. Press GREEN button.  
By cursor buttons move the selected program  
to the decided programme space and press  
GREEN button again.  
Name:  
To change the name of a decided programme,  
that programme is selected and pressed to  
the YELLOW button. The following menu  
comes to screen.  
Moving cursor to four direction you can reach  
30 programmes in the same page. By scroll-  
ing the pages up or down by pressing the cur-  
sor buttons you can select all the  
programmes in TV mode (except the AV  
mode).  
ENGLISH - 17 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The first letter of the selected name is high-  
lighted. To change that letter “ “ / “ ” button  
can be used, and to select the other letters,  
source select  
By pressing “ “ / “ ” button, select source  
select in settings menu. "<ok> to activate  
source selection menu" is seen on the  
“ “ / “ ” button can be used. If the cursor is  
at the last letter of the Programme Name,  
screen. By pressing “ “ / “ ” or “OK” button,  
you can enter the source select menu.  
pressing “ ” button moves the cursor at the  
beginning. On the contrary, if the cursor is at  
the beginning of the Programme Name,  
pressing “ “ button moves the cursor at the  
end.  
country  
By pressing “ “ / “ ” button, select country.  
"right/left to change country" is seen on the  
screen. By pressing “ “ / “ ” button, you  
should select the country where you are.  
autoset  
By pressing “ “ / “ ” button, select autoset.  
"right/left to start aps function" is seen on  
In source select menu, come on one of the  
sources by pressing “ “ / “ ” button and  
the screen. When “ “ / “ ” or “OK” button is  
pressed, the following menu comes to the  
screen. If you want to cancel autoset function,  
press “MENU” button. You return to aps menu.  
select it by pressing “ ” button. The source  
types are Tuner, Scart 1, Scart 1 RGB,  
Scart 2, Scart 2 RGB, PC, FAV and S-Video.  
If you press “MENU” button after autoset is  
started, program table appears on the screen.  
Other Features  
TV Status  
Programme Number, Programme Name  
and Sound Indicator are displayed on the up-  
per right side of the screen. Source is also  
displayed with them on the right bottom side  
of the screen. They are displayed after  
programme change during 3 seconds or  
ꢀ0(18!  
ꢀ2.!  
If “OK” button is pressed, autoset function starts  
and the following menu comes to the screen.  
when “ ” button is pressed.  
Programme Number  
ꢀꢁꢀ  
35ꢀꢁꢂꢀ  
Programme Name (5 characters)  
ꢃ
After autoset is finalized, the program table  
comes to the screen.In the programme table  
you will see the programme numbers and  
names assigned to the programmes.  
These OSD’s are displayed when a new pro-  
gramme is entered by digit button, by press-  
ing “  
” or “  
” button or “BACK” but-  
ton.  
If you do not accept the locations and / or the  
programme names of programmes, you can  
change them in aps submenu in the settings  
menu. (See page 17 for Program table expla-  
nation.)  
Pressing “  
” button when PC mode se-  
lected shows sound indicator and the resolu-  
tion of the screen.  
When “ ” button is pressed twice the cur-  
ENGLISH - 18 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
In Mono broadcast or in forced-mono (for ste-  
reo broadcast).  
rent time information, captured from Teletext  
will be displayed on the screen.  
67(5(2  
In Stereo broadcast.  
'8$/ꢀ$  
Active window switch  
By pressing “  
” button in any modes, PIP  
window appears on the screen.  
If dual broadcast detected. Dual A is selected  
in default and also can be selected  
In PIP mode “ “ / “ ” buttons or “ ” button  
are used to select active window.  
after Dual B by Remote Control.  
'8$/ꢀ%  
If Dual B selected by Remote Control.  
Muting the Sound  
Press the " "(muting) button to turn off and  
on the sound. One of the sound marks below  
will appear on the upper left side of the screen.  
The mark will also appear when the left or  
Right button pressed.  
It is placed in the upper left side of the screen  
when enabled.  
Note: PC screen is not displayed in PIP win-  
dow.  
Sound Off  
Sound On  
Freeze Picture  
When sound is off, pressing "  
+"/"-  
"
You can freeze the picture on the screen by  
pressing “OK” button. Press OK button again  
to back to the moving picture. Display layout  
should be selected as full screen for this fea-  
ture. At PIP layouts; this function is invalid.  
buttons restores the previous volume level  
Sleep Timer  
Sleep Timer mode OSD is displayed when  
YELLOW button is pressed.  
The Sleep Timer is used to turn the TV off after  
a defined period of time after selecting this  
item. The timer can be programmed between  
0 and 120 minutes in steps of 10 minutes. (0,  
10, 20, 30, 40, ... , 120)  
If PIP layout is selected, the sound mark is  
displayed at the upper middle of the PIP win-  
dow.  
If sleep timer is activated, at the end of the  
selected the time, the TV goes automatically  
to stand-by mode.  
Hyper Sound  
By selecting Hyper Sound in sound menu or  
by pressing the “  
“ button on your remote  
Sound Modes  
control, Pseudo/Spatial effect can be turned  
on or off. In Mono transmission the left and  
right channels will be added at left channel  
and dummy stereo effect will introduced to  
end-user.  
The alternatives of the modes are Mono, Ste-  
reo, Dual A and Dual B. This indicator is dis-  
played under the programme number indica-  
tor on the screen. "I-II" button is used to select  
Mono, Stereo, Dual A or Dual B.  
In stereo transmission it yields a phase dif-  
0212  
ENGLISH - 19 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ference between left and right channels. Hyper  
Sound selection will be displayed on the  
screen when the TV Status button is pressed  
or programme is changed.  
• For 16:9 aspect ratio pictures that have been  
squeezed into a normal picture (4:3 aspect  
ratio), use the FULL mode to restore the pic-  
ture to its original shape.  
16:9 ZOOM:  
EXT Modes  
This zooms up the wide picture (16:9 aspect  
ratio) to the full screen.  
By pressing the “AV“ button or via source se-  
lect menu, you can switch your TV to EXT  
modes (except being in Teletext). Pressing this  
button will consecutively switch the TV in one  
of the optional EXT modes: Tuner, Scart 1,  
Scart 1 RGB, Scart 2, Scart 2 RGB, PC, FAV  
and SVideo.  
16:9ZOOM SUBTITLE:  
While watching VCR; vcr item in options menu  
should be set to on.  
This zooms up the wide picture (16:9 aspect  
ratio) with subtitles to the full screen.  
Zoom Modes  
Zoom mode bar is displayed when RED  
button(ZOOM) is pressed. You can change the  
screen size according to the picture aspect  
ratio. Select the optimum one from the follow-  
ing ZOOM modes.  
REGULAR:  
Use to view a normal picture (4:3 aspect ratio)  
as this is its original shape.  
AUTO:  
When a WSS (Wide Screen Signalling) sig-  
nal, which shows the aspect ratio of the pic-  
ture, is included in the broadcast signal or the  
signal from an external device, the TV auto-  
matically changes the ZOOM mode to 16:9  
ZOOM mode PANORAMIC or FULL mode ac-  
cording to the WSS signal.  
PANORAMIC:  
This stretches the left and right sides of a nor-  
mal picture (4:3 aspect ratio) to fill the screen,  
without making the picture appear unnatural.  
• When the AUTO mode does not function cor-  
rectly due to poor WSS signal quality or when  
you want to change the ZOOM mode, change  
to another ZOOM mode manually.  
Using the different screen formats  
The top and bottom of the picture are slightly  
cut off.  
Press the “ “ or “ ” button to select the differ-  
ent modes: Auto, Full, 16:9 Zoom,16:9 Zoom  
Subtitle, Regular, Panoramic, 14:9 Zoom  
modes.  
14:9 ZOOM:  
This zooms up the wide picture (14:9 aspect  
ratio) to the upper and lower limits of the  
screen.  
FULL:  
This uniformly stretches the left and right sides  
of a normal picture (4:3 aspect ratio) to fill the  
wide TV screen.  
ENGLISH - 20 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ber, “ ” sign will replace the page number  
and flash until the entered page number is  
found. Then the page number will replace  
Teletext  
Teletext is an information system that displays  
text on your TV screen. Using the Teletext in-  
formation system you can view a page of in-  
formation on a subject that is available in the  
list of contents (index).  
“
” sign again. Now you can display this  
teletext page pressing “ “ button  
To Select Double Height Text  
The menu is not available in text mode.  
• Press “  
“ button for the top half of the infor-  
Contrast, brightness or colour control is not  
available, but volume control is available in  
text mode.  
mation page to be displayed in double height  
text.  
• Press “  
“ button again for the bottom half  
To Operate Teletext  
of the information page to be displayed in  
double height text.  
• Select a TV station on which Teletext is being  
transmitted.  
• Press “  
“ button once more for the full  
page of normal height text.  
• Press “  
” button. Usually the list of con-  
tents (index) is displayed on the screen.  
To Reveal “Concealed”  
Information  
• Pressing “  
“ button once will reveal an-  
swers on a quiz or games page.  
• Pressing “  
“ button again will conceal the  
revealed answers.  
To Select a Page Of Teletext  
To Stop Automatic Page Change  
• Press the appropriate digit buttons for the  
required Teletext page number.  
The teletext page you have selected may con-  
tain more information than what is on the  
screen; the rest of the information will be dis-  
played after a period of time.  
The selected page number is displayed at the  
top left corner of the screen. The Teletext page  
counter searches until the selected page  
number is located, so that the desired page is  
displayed on the screen.  
• Press “  
“ button to stop the automatic  
page change.  
• Press “  
” button to move the Teletext  
• Press “  
“ button again to allow the next  
screen forward one page at a time.  
page to be displayed.  
• Press “  
” button to move the Teletext  
To Select A Subcode Page  
screen backward one page at a time.  
Subcode pages are subsections of long Tele-  
text pages that can only be displayed on the  
screen one section at a time.  
To Select Index Page  
• To select the page number of the index (gen-  
• Select the required Teletext page.  
erally page 100), press “  
“ button.  
Searching for a teletext page while • Press “  
“ button.  
watching TV  
• Select the required subcode page number  
by pressing four digit buttons (e.g. 0001).  
• In the Teletext mode pressing “ “ button  
will switch the screen to the TV mode. In the  
TV mode enter a page number using digit  
buttons. As you enter last digit of page num-  
• If the selected subcode page is not displayed  
in a short time, press “  
“ button. TV  
programme will be displayed on the screen.  
ENGLISH - 21 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Teletext page number will be displayed on  
the upper left corner of the screen when the  
selected page is found.  
Connect Peripheral  
Equipment  
There is a wide range of audio and video equip-  
ment that can be connected to your TV.  
• Press “  
Teletext page.  
“ button to display the selected  
The following connection diagrams show you  
where the different equipment should be con-  
nected at the back or right side of the TV.  
To Exit Teletext  
• Press “ ” button. The screen will switch to  
TV mode.  
Via The Euroconnector  
Fastext  
TFT TV has 2 Euroconnector sockets. If you  
want to connect peripherals (e.g. video, de-  
coder, etc.) which have Euroconnectors, to the  
TV, use Scart 1 or Scart 2 inputs.  
Your TV supports the 10 page Teletext system.  
When the page number of any of the 10 pages  
in memory is entered, the system will not search  
for the requested page; instead it will display the  
page automatically.  
If an external device is connected via Euro-  
connector sockets TV is switched to EXT mode  
automatically. If the signal is RGB, select RGB  
in the source select menu to view picture. If  
the external device is connected to Scart 1,  
choose Scart 1 RGB. If the external device is  
connected to Scart 2, choose Scart 2 RGB.  
• Press “  
screen forward one page at a time.  
” button to move the Teletext  
• Press “  
” button to move the Teletext  
screen backward one page at a time.  
For Fastext  
Via Ant Input  
The subject-heading for the information may  
have a particular color.  
If you want to connect to your TV, peripherals  
like video recorders or decoders, but the de-  
vice you want to connect does not have Euro-  
connector, you should connect it to the ANT  
input of the TV.  
• Press an appropriate RED, GREEN, YELLOW  
or BLUE button in order to reach the relevant  
page quickly.  
For TOP text  
If the VCR is connected via antenna input it  
is suggested to use the Programme 0.  
TOP text mode of operation will be activated  
automatically according to the transmission.  
Decoder  
• If TOP text transmission is present, color  
coded buttons will appear in status row.  
Cable TV offers you a wide choice of programs.  
Most of them are free, others are to be paid for  
by the viewer. This means that you will need to  
subscribe to the broadcasting organisation  
whose programmes you wish to receive. This  
organisation will supply you a corresponding  
decoder unit to allow the programmes to be  
unscrambled.  
• If TOP text transmission is not present, sta-  
tus row will not appear.  
The subject-heading for information may be  
located in colored box.  
In Top mode the “  
or  
” commands  
will request the next or previous page respec-  
tively. If TOP text transmission is not available,  
in case of operation of these commands,  
wraparound occurs. For example page 100  
appears to be one greater than page 199.  
For further information ask your dealer. See  
also the booklet supplied with your decoder.  
Connect a decoder with an aerial socket  
to the TV  
• Connect the aerial cable.  
ENGLISH - 22 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connect a decoder without an aerial  
socket to the TV  
Camera And Camcorder to  
Connect to FAV Input  
• Connect the decoder to the TV with a  
eurocable to Scart 1.  
Connect your camera or camcorder FAV input  
at the right side of the TV.  
TV And Video Recorder  
• Connect your equipment to the TV via VIDEO  
(yellow), AUDIO R (red) and AUDIO L (white)  
inputs. You should connect the jacks to the  
input in the same color.  
• Connect the aerial cables.  
Better picture quality can be obtained if you  
also connect a eurocable to SCART sockets.  
To Connect to SVideo Input  
Playback NTSC  
Connect your camera or camcorder SVideo  
input at the right side of the TV.  
To use this option you can;  
• Connect NTSC VCR player to Euroconnec-  
tor at the rear side of the TV.  
• Connect your equipment to the TV via SVideo  
input and audio inputs of FAV inputs by using  
SVideo cables.  
• Connect NTSC VCR player to RCA Jacks at  
the right side of the TV.  
Connect The Decoder To The  
Video Recorder  
Then, press “AV” button to select proper  
source.  
Some video recorders have a special euro-  
connector for decoder.  
Copy Facility  
Source selection for VCR recording.  
• Select options menu.  
• Connect a eurocable to the euroconnector of  
your decoder and to the special eurocon-  
nector of your video recorder. See also the  
booklet of your video recorder.  
• Select scart 2 out source pressing “ “ /  
“
” button.  
• To connect your video recorder to the TV, see  
TV and Video Recorder section.  
• Select Scart 1 to copy the picture from tuner.  
• Select Scart 2 to copy the picture from Tuner,  
FAV or Scart 1.  
If you want to connect more equipment to your  
TV, consult your dealer.  
Search For And Store The Test  
Signal Of The Video Recorder  
Connecting Headphones  
Use the stereo headphone socket at the right  
side of the TV, to connect headphones.  
• Unplug the aerial cable from the aerial socket  
“ANT” of your video recorder.  
You can adjust the headphones volume and  
sound mode from the audio menu. See page  
14 for details.  
• Switch on your TV and put the video recorder  
on the test signal. (See the booklet for your  
video recorder.)  
• Enter the tv tuner menu in settings menu.  
Enter the programming menu in tv tuner  
menu and select manual search.  
• Search for the test signal of your video re-  
corder in the same way as you searched for  
and stored the TV signals. See program-  
ming menu. Store the test signal under  
programme number 0.  
• Replace the aerial cable in the aerial socket  
“ANT” of your video recorder once you have  
stored the test signal.  
ENGLISH - 23 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AntennaConnections  
ConnectPeripheralEquipment  
HEADPHONE  
AUDIO  
VIDEO  
&$0&25'(5  
FORSATELLITERECEIVER  
DECODER  
ENGLISH - 24 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PCInputTypical Display Modes  
The display has a maximum resolution of 1280 x 768, vertical sync. frequency range of 50-75 Hz  
and a horizontal sync. frequency range of 30-69 KHz.  
The following table is an illustration of some of the typical video display modes.  
5HVROXWLRQ  
)UHTXHQF\ꢁ  
0RGH  
+RUL]RQWDO 9HUWLFDO +RUꢀꢁꢂN+]ꢃ 9HUꢀꢁꢂ+]ꢃ  
ꢀ
ꢇ
ꢄ
ꢂ
ꢆ
ꢁ
ꢉ
ꢈ
ꢊ
ꢁꢂꢃ  
ꢁꢂꢃ  
ꢁꢂꢃ  
ꢉꢇꢃ  
ꢈꢃꢃ  
ꢈꢃꢃ  
ꢈꢃꢃ  
ꢀꢃꢇꢂ  
ꢀꢃꢇꢂ  
ꢀꢃꢇꢂ  
ꢀꢇꢈꢃ  
ꢂꢃꢃ  
ꢂꢈꢃ  
ꢂꢈꢃ  
ꢂꢃꢃ  
ꢁꢃꢃ  
ꢁꢃꢃ  
ꢁꢃꢃ  
ꢉꢁꢈ  
ꢉꢁꢈ  
ꢉꢁꢈ  
ꢉꢁꢈ  
ꢄꢀꢅꢆ  
ꢄꢉꢅꢊ  
ꢄꢉꢅꢆ  
ꢄꢀꢅꢆ  
ꢄꢉꢅꢊ  
ꢂꢈꢅꢀ  
ꢂꢁꢅꢊ  
ꢂꢈꢅꢂ  
ꢆꢁꢅꢆ  
ꢁꢃꢅꢃ  
ꢂꢉꢋꢁ  
ꢁꢃ  
ꢉꢇ  
ꢉꢆ  
ꢉꢃ  
ꢁꢃ  
ꢉꢇ  
ꢉꢆ  
ꢁꢃ  
ꢉꢃ  
ꢉꢆ  
ꢁꢃ  
ꢀꢃ  
ꢀꢀ  
The native resolution of the TFT-LCD Panel is 1024 x 768. Therefore using Mode 10 is advised  
to get the best PC input display quality.  
PIPCombinationRestrictions  
ꢀꢀꢀꢀꢀꢀꢀHhv  
QDQ  
T86SUꢀ ꢀ T86SUꢀ!ꢀ  
UVI@S T86SUꢀ  T86SUꢀ!  
A6W  
Q8  
TꢁWD9@P  
SB7  
SB7  
UVI@S  
T86SUꢀ  
T86SUꢀ!  
T86SUꢀ ꢀ  
SB7  
T86SUꢀ!ꢀ  
SB7  
A6W  
Q8  
TꢁWD9@P  
Uuv†ꢀp‚qv‡v‚ꢀv†ꢀ‚‡ꢀƒ‚††viyr  
ENGLISH - 25 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control  
Tips  
Your TV no longer responds to the remote con-  
trol. Perhaps the batteries are exhausted.  
Replace the batteries.  
Care Of The Screen  
Clean the screen with a slightly damp, soft  
cloth. Do not use abrasive solvents as they  
may damage the TV screen coating layer.  
Have you selected the wrong menu? Press  
“BACK” button to return to TV mode or press  
“MENU” button to return to the previous menu.  
Poor Picture  
No solution  
Have you selected the correct TV system? Is  
your TV set or house aerial located too close  
to the loudspeakers, non-earthed audio equip-  
ment or neon lights, etc.?  
Switch your TV set off and on. If this does not  
work, call the service personnel; never attempt  
to repair it yourself.  
Mountains or high buildings can cause double  
pictures or ghost images. Sometimes you can  
improve the picture quality by changing the  
direction of the aerial.  
Is the picture or Teletext unrecognisable?  
Check if you have entered the correct frequency.  
The picture quality may degrade when two  
peripherals are connected to the TV at the  
same time. In such a case, disconnect one of  
the peripherals.  
No Picture  
Is the aerial connected properly? Are the plugs  
connected tightly to the aerial socket? Is the  
aerial cable damaged? Are suitable plugs  
used to connect the aerial? If you are in doubt,  
consult your dealer.  
No Picture means that your TV is not receiv-  
ing any transmission. Have you pressed the  
correct buttons on the remote control? Try once  
more.  
PC Picture  
If no PC picture appears, check the D-SUB  
cable is connected properly. Check that your  
PC's resolution set correctly. See page 25 for  
supported modes.  
Sound  
You can not hear any sound. Did you perhaps  
interrupt the sound, pressing “ ” button? Are  
external speakers connected to the TV?  
Sound is coming from only one of the speak-  
ers. Is the balance set to one direction ex-  
treme? See audio menu.  
ENGLISH - 26 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Model  
Item  
LT-30E45SU  
Broadcasting Systems  
Channels and  
Frequencies  
PAL SECAM, B/G, D/K, I/I', L/L'  
VHF (VL) 46,25 MHz - 168,25 MHz  
VHF (VH) 175,25 MHz - 463,25 MHz  
UHF  
471,25 MHz - 863,25 MHz  
Cable TV(S1-S20/ S21-S41)  
Video: Analog 0,7 Vp-p 75 ohm positive  
Sync: TTL Level positive or negative, Seperate sync.  
30 - 69 KHz  
Input Signal  
Horizontal Timing  
Vertical Timing  
50 - 75 Khz  
Dot Rate  
78,75 MHz max.  
Panel Size  
29,5” (measured diagonally)  
Visible Picture Size  
Display Resolution  
Number of Preset Channels  
Channel Indicator  
RF Aerial Output  
Power Requirements  
Power Consumption (W)  
Sound Systems  
Audio Output  
643 mm horizontal x 386 mm vertical  
1280 x 768 max. (WXGA)  
100  
On Screen Display (OSD)  
75 Ohm (unbalanced)  
220-240 V AC, 50 Hz  
150 W (max) / STAND-BY <4W  
German , Nicam Stereo  
2 x 8 WRMS. (%10 THD)  
EXT-1Terminal  
Euroconnector (21-pin, SCART 1) (bottom of the cabinet)  
• Video Input, Audio L/R Inputs and RGB inputs are available.  
• TV broadcast outputs (Video and Audio L/R) are available.  
Euroconnector (21-pin, SCART 2) (bottom of the cabinet)  
EXT-2Terminal  
EXT-3Terminal  
• Video Input, S-VIDEO (Y/C) input, Audio L/R and RGB inputs are available.  
• Video and Audio L/R outputs are available.  
• T-V LINK functions are available.  
RCA connectors x 3 (side of the cabinet)  
S-VIDEO connector x 1 (side of the cabinet)  
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.  
RCA connectors x 2 (bottom of the cabinet)  
• Audio L-R Line Outs are available  
Audio Output  
PC IN terminal  
Analog RGB D-SUB 15 x 1  
• PC signal is available (refer to page 25 for details of the signals which can be input)  
Stereo mini-jack (3.5 mm diameter)  
PC AUDIO IN terminal  
Dimensions (W x H x D)  
847 mm x 522 mm x 260 mm  
847 mm x 490 mm x 102 mm (TV only)  
14.8 kg (with stand) / 13 kg (TV only)  
Weight  
Accessories  
Remote control unit x 1 (RM-C1860) / AA/R6 dry cell battery x 2  
Power cord x 1  
Headphone jack  
Stereo mini-jack (3.5 mm diameter)  
ENGLISH - 27 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Infinity Portable Speaker TSS 3 IN 1 User Manual
Insignia DVD Player I PD1020 User Manual
Intel Power Supply SX220 User Manual
JVC Digital Camera GR DV4000 User Manual
JVC DVD Player XV M556TN User Manual
JVC Universal Remote HR DVS3EU User Manual
Kenmore Gas Grill 14116681 User Manual
Kenwood Stereo Receiver VR 606 VR 616 User Manual
Kodak Digital Camera V530 User Manual
Korg Electronic Keyboard MMT User Manual