ENGLISH
DIGITAL VIDEO CAMERA
CONTENTS
AUTOMATIC
DEMONSTRATION
GR-D22
6
GETTING STARTED
7 – 10
Please visit our Homepage on the World Wide Web for Digital
Video Camera:
TAPE
For Accessories:
RECORDING &
PLAYBACK
11 – 15
16 – 28
ADVANCED
FEATURES
REFERENCES 29 – Back Cover
For Customer Use:
Enter below the Model No. and Serial
No. which is located on the bottom of the
camcorder. Retain this information for
future reference.
Model No.
Serial No.
INSTRUCTIONS
LYT1225-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Dear Customer,
Thank you for purchasing this digital video camera. Before use, please read “SAFETY PRECAUTIONS”
and “IMPORTANT PRODUCT SAFETY INSTRUCTIONS” (੬ pgs. 3 and 4) to ensure safe use of this
product.
SAFETY PRECAUTIONS
CAUTION
WARNING:
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
NOTES:
● The rating plate (serial number plate) and safety
caution are on the bottom and/or the back of the main
unit.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
● The rating information and safety caution of the AC
Adapter are on its upper and lower sides.
CAUTIONS:
● This camcorder is designed to be used with NTSC-type color television signals. It cannot be used for playback with a
television of a different standard. However, live recording and LCD monitor/viewfinder playback are possible
anywhere.
● Use the JVC BN-V408U/V416U/V428U battery packs and, to recharge them or to supply power to the camcorder
from an AC outlet, use the provided multi-voltage AC Adapter. (An appropriate conversion adapter may be necessary
to accommodate different designs of AC outlets in different countries.)
When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all sides to
allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)
No naked flame sources, such as lighted candles, should be placed on the apparatus.
When discarding batteries, environmental problems must be considered and the local rules or laws governing
the disposal of these batteries must be followed strictly.
The apparatus shall not be exposed to dripping or splashing.
Do not use this equipment in a bathroom or places with water.
Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases,
potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
This product has a fluorescent lamp that contains a small amount of mercury. Disposal of these materials may
be regulated in your community due to environmental considerations.
For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance:
<http://www.eiae.org>
EN
None
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not point the lens or the viewfinder directly into the sun. This can cause eye injuries, as well as lead to the
malfunctioning of internal circuitry. There is also a risk of fire or electric shock.
CAUTION!
The following notes concern possible physical damage to the camcorder and to the user.
When carrying, be sure to always securely attach and use the provided shoulder strap. Carrying or holding the
camcorder by the viewfinder and/or the LCD monitor can result in dropping the unit, or in a malfunction.
Take care not to get your finger caught in the cassette holder cover. Do not let children operate the camcorder,
as they are particularly susceptible to this type of injury.
Do not use a tripod on unsteady or unlevel surfaces. It could tip over, causing serious damage to the
camcorder.
CAUTION!
Connecting cables (Audio/Video, S-Video, etc.) to the camcorder and leaving the unit on top of the TV is not
recommended, as tripping on the cables will cause the camcorder to fall, resulting in damage.
IMPORTANT PRODUCT SAFETY INSTRUCTIONS
(1) Read these instructions.
(2) Keep these instructions.
(3) Heed all warnings.
(10) Use only with the cart, stand,
tripod, bracket, or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use
caution when moving the cart/
apparatus combination to
avoid injury from tip-over.
(4) Follow all instructions.
(5) Do not use this apparatus near water.
(6) Clean only with dry cloth.
(11) Unplug this apparatus during lightning storms or
(7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
when unused for long periods of time.
(12) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
(8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
(9) Only use attachments/accessories specified by
the manufacturer.
Ⅲ This camcorder is designed exclusively for the digital video cassette. Only cassettes marked “
”
can be used with this unit.
Before recording an important scene . . .
..... make sure you only use cassettes with the Mini DV mark
.
..... remember that this camcorder is not compatible with other digital video formats.
..... remember that this camcorder is intended for private consumer use only. Any commercial use without proper
permission is prohibited. (Even if you record an event such as a show, performance or exhibition for personal
enjoyment, it is strongly recommended that you obtain permission beforehand.)
EN
None
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PROVIDED ACCESSORIES
or
Lens Cap
(See below for
attachment)
Battery Pack
BN-V408U
AC Adapter AP-V11U or AP-V13U
Shoulder Strap
Audio/Video Cable
(ø3.5 mini-plug to
RCA plug)
NOTE:
In order to maintain optimum performance of the camcorder, provided cables may be equipped with one or more core
filter. If a cable has only one core filter, the end that is closest to the filter should be connected to the camcorder.
HOW TO ATTACH THE LENS CAP
To protect the lens, attach the provided lens cap to the camcorder as shown in the illustration.
NOTE:
To confirm the lens cap is on correctly make sure the cap is flush to the camera.
1 Make sure the arrow (L) is
2
3
pointing upward.
Arrow
EN
None
5
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC DEMONSTRATION
Automatic Demonstration takes place when
“DEMO MODE” is set to “ON” (factory-preset).
#
Ⅲ Automatic Demonstration starts when there is no operation for
about 3 minutes after the Power Switch r is set to “ ” or “
and no cassette is in the camcorder.
”
Ⅲ Performing any operation during the demonstration stops the
demonstration temporarily. If no operation is performed for more
than 3 minutes after that, the demonstration will resume.
Ⅲ “DEMO MODE” remains “ON” even if the camcorder power is
e
turned off.
Ⅲ To cancel Automatic Demonstration:
1. Set the Power Switch r to “ ” while pressing down the Lock
Button e located on the switch and press the MENU/VOLUME
wheel # in. The Menu Screen appears.
r
Sub Menu
2. Rotate the MENU/VOLUME wheel # to select “
(SYSTEM)”
and press it.
SYSTEM
3. Rotate the MENU/VOLUME wheel # to select “DEMO MODE”
and press it. The Sub Menu appears.
DEMO MODE
–
OFF
ON
4. Rotate the MENU/VOLUME wheel # to select “OFF” and press
it.
5. Rotate the MENU/VOLUME wheel # to select “ RETURN”,
and press it twice. The normal screen appears.
NOTE:
If you do not detach the Lens Cap, you cannot see the actual changes of the Automatic Demonstration activated on
the LCD monitor or viewfinder.
EN
None
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Power
!
w
r
CHARGING THE BATTERY PACK
1With the arrow on the battery pack pointing upward,
push the battery pack slightly against the battery pack
mount !, then slide up the battery pack until it locks in
place.
Arrow
2Set the Power Switch r to “OFF (CHARGE)”.
Connect the AC Adapter to the camcorder.
3Plug the AC Adapter into an AC outlet. The POWER/
CHARGE lamp w on the camcorder blinks to indicate
charging has started.
To DC
connector
Battery pack
AC Adapter
i
4When the POWER/CHARGE lamp w goes off,
charging is finished. Unplug the AC Adapter from the
AC outlet. Disconnect the AC Adapter from the
camcorder.
To AC outlet
To Detach The Battery Pack:
Slide the battery pack down slightly while sliding down
BATT. RELEASE i to detach it.
ATTENTION
Battery pack
BN-V408U
Charging time
approx. 1 hr. 30 min.
approx. 3 hrs.
Before detaching the power source, make sure that the
camcorder’s power is turned off. Failure to do so can
result in a camcorder malfunction.
BN-V416U (optional)
BN-V428U (optional)
approx. 5 hrs.
INFORMATION
Charging times are for a fully discharged battery pack.
The extended-use battery pack kit is a set composed of
a battery pack and AC Power Adapter/Charger:
USING THE BATTERY PACK
VU-V840 KIT : BN-V840U battery pack & AA-V15U AC
Power Adapter/Charger
VU-V856 KIT : BN-V856U battery pack & AA-V80U AC
Power Adapter/Charger
Perform step 1 of “CHARGING THE BATTERY PACK”.
Approximate recording time
Read the kit's instruction manual before using.
Also, by using the optional JVC VC-VBN856U DC
Cord, it will be possible to connect BN-V840U or
BN-V856U battery packs to the camcorder and supply
power directly to the camcorder.
Battery pack
LCD monitor on
Viewfinder on
BN-V408U
1 hr. 10 min.
1 hr. 40 min.
BN-V416U
(optional)
2 hrs. 30 min.
4 hrs. 20 min.
5 hrs. 20 min.
8 hrs. 10 min.
3 hrs. 30 min.
6 hrs. 20 min.
7 hrs. 30 min.
11 hrs. 10 min.
BN-V428U
(optional)
NOTES:
● If the protective cap is attached to the battery pack,
remove it first.
BN-V840U
(optional)
● During charging, the camcorder cannot be operated.
● Charging is not possible if the wrong type of battery is
used.
● When charging the battery pack for the first time or after
a long storage period, the POWER/CHARGE lamp w
may not light. Remove the battery pack from the
camcorder, then try charging again.
● If a fully-charged battery’s operation time remains
extremely short, the battery is worn out. Please purchase
a new one.
● Recording time is reduced significantly when Zoom or
Record-Standby mode is engaged repeatedly or the LCD
monitor is used repeatedly.
BN-V856U
(optional)
USING AC POWER
Connect the AC Adapter to the camcorder as shown in
the following illustration.
• The provided AC Adapter features automatic voltage
selection in the AC range from 110 V to 240 V.
● Before extended use, it is recommended that you prepare
enough battery packs to cover 3 times the planned
shooting time.
Continued on next page.
EN
GETTING STARTED
7
Download from Www.Somanuals.com. All Manuals Search And Download.
● Since the AC Adapter processes electricity internally,
it becomes warm during use. Be sure to use it only in
well-ventilated areas.
● The following operation stops charging:
• Set the Power Switch r to “PLAY”, “ ” or “ ”.
• Disconnect the AC Adapter from the camcorder.
• Unplug the AC Adapter from the AC outlet.
• Detach the battery from the camcorder.
Grip Adjustment
1Separate the Velcro strip.
2Pass your right hand through the loop and grasp the
grip.
3Adjust your thumb and fingers through the grip, to
easily operate the Recording Start/Stop button ) and
Power Switch r and Power Zoom Lever %. Be sure to
fasten the Velcro strip to your preference.
●
This camcorder will be automatically turned off if its power
is supplied from the AC adapter and about 5 minutes pass
since it has entered into the recording standby mode with
a cassette inserted. If, under those conditions, the battery
is attached to the camcorder, its charging will start.
%
● Using the optional AA-V40U AC Power Adapter/Charger,
you can charge the BN-V408U/V416U/V428U battery
pack without the camcorder. However, it cannot be used
as an AC adapter.
● To avoid interference with reception, do not use the AC
Adapter near a radio.
● Perform charging where the temperature is between
10°C and 35°C (50°F and 95°F). 20°C to 25°C (68°F to
77°F) is the ideal temperature range for charging. If the
environment is too cold, charging may be incomplete.
● Charging time varies according to the ambient
temperature and the status of the battery pack.
r
)
About Batteries
Viewfinder Adjustment
DANGER! Do not attempt to take the batteries apart, or
expose them to flame or excessive heat, as it may
cause a fire or explosion.
1Set the Power Switch r to “ ” or “ ” while
pressing down the Lock Button e located on the
switch.
WARNING! Do not allow the battery or its terminals to
come in contact with metals, as this can result in a
short circuit and possibly start a fire.
2Pull out the viewfinder fully and adjust it manually for
best viewability.
The Benefits Of Lithium-Ion Batteries
Lithium-ion battery packs are small but have a large
power capacity. However, when one is exposed to cold
temperatures (below 10°C/50°F), its usage time
becomes shorter and it may cease to function. If this
happens, place the battery pack in your pocket or other
warm, protected place for a short time, then re-attach it
to the camcorder. As long as the battery pack itself is
not cold, it should not affect performance.
3Turn the Diopter Adjustment Control ( until the
indications in the viewfinder are clearly focused.
PAUSE
(If you’re using a heating pad, make sure the battery
pack does not come in direct contact with it.)
(
Lithium-ion is vulnerable in colder temperatures.
e
r
EN
GETTING STARTED
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Shoulder Strap Attachment
Loading/Unloading A Cassette
The camcorder needs to be powered up to load or eject
a cassette.
1Thread the strap through the eyelet q, then fold it
back and thread it through the buckle. Repeat the
procedure to attach the other end of the strap to the
other eyelet q located under the Grip Strap. Confirm
the strap is not twisted.
1Slide and hold OPEN/EJECT o in the direction of
the arrow then pull the cassette holder cover open until
it locks. The cassette holder opens automatically.
• Do not touch internal components.
2Insert or remove a tape and press “PUSH HERE” to
close the cassette holder.
• Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely before
closing the cassette holder cover.
• When the battery’s charge is low, you may not be able
to close the cassette holder cover. Do not apply force.
Replace the battery with a fully charged one before
continuing.
q
3Close the cassette holder cover firmly until it locks
into place.
To Protect Valuable Recordings:
Slide the erase protection tab on the back of the
tape in the direction of “SAVE”. This prevents the
tape from being recorded over. To record on this
tape, slide the tab back to “REC” before loading it.
Tripod Mounting
CAUTION
When attaching the camcorder to a tripod, extend its
legs to stabilize the camcorder. It is not advised to use
small sized tripods. This may cause damage to the unit
by falling over.
Make sure the
window side
is facing out.
Cassette holder
1To attach the camcorder to a tripod, align the
direction stud and screw to the stud hole y and
mounting socket u on the camcorder. Then tighten the
screw clockwise. Some tripods are not equipped with
studs.
Cassette
holder
o
cover
u
y
Be sure to press only the section labeled “PUSH
HERE” to close the cassette holder; touching other
parts may cause your finger to get caught in the
cassette holder, resulting in injury or product damage.
Approximate recording time
Recording mode
Tape
SP
LP
30 min.
60 min.
80 min.
30 min.
60 min.
80 min.
45 min.
90 min.
120 min.
NOTES:
● The cassette holder cannot be opened unless a power
supply is attached.
Continued on next page.
EN
GETTING STARTED
9
Download from Www.Somanuals.com. All Manuals Search And Download.
● It takes a few seconds for the cassette holder to open. Do
not apply force.
CAMERA D I SPLAY
CAMERA D I SPLAY
BR I GHT
ON SCREEN
DATE / T I ME
T I ME CODE
CLOCK
–
–
–
LCD / TV
AUTO
● There may be a delay after you open the cassette holder
cover until the cassette holder opens. Do not use force.
● If you wait a few seconds and the cassette holder does
not open, close the cassette holder cover and try again. If
the cassette holder still does not open, turn the
camcorder off then on again.
OFF
DEC 25 ’03
5 : 30 PM
CLOCK
ADJ .
DEC 25 ’03
5 : 30 PM
ADJ .
RETURN
● If the tape does not load properly, open the cassette
holder cover fully and remove the cassette. A few minutes
later, insert it again.
● When the camcorder is suddenly moved from a cold
place to a warm environment, wait a short time before
opening the cassette holder cover.
● Once the cassette holder is closed, it recedes automati-
cally. Wait until it recedes completely before closing the
cassette holder cover.
#
w
● Closing the cassette holder cover before the cassette
holder comes out may cause damage to the camcorder.
● Even when the camcorder is switched off, a cassette can
be loaded or unloaded. After the cassette holder is closed
with the camcorder switched off, however, it may not
recede. It is recommended to turn the power on before
loading or unloading.
e
r
● When resuming recording, once you open the cassette
holder cover a blank portion will be recorded on the tape
or a previously recorded scene will be erased (recorded
over) regardless of whether the cassette holder came out
or not. See page 13 for information about recording from
the middle of a tape.
Recording Mode Setting
Set the tape recording mode depending on your
preference.
Date/Time Settings
1Set the Power Switch r to “ ” while pressing
down the Lock Button e located on the switch, and
open the LCD monitor fully or pull out the viewfinder
fully. The POWER/CHARGE lamp w lights and the
camcorder is turned on.
The date/time is recorded onto the tape at all times, but
its display can be turned on or off during playback
(੬ pg. 24).
1Set the Power Switch r to “ ” while pressing
down the Lock Button e located on the switch, and
open the LCD monitor fully or pull out the viewfinder
fully. The POWER/CHARGE lamp w lights and the
camcorder is turned on.
2Press the MENU/VOLUME wheel # in. The Menu
Screen appears.
3Rotate the MENU/VOLUME wheel # to select
“
(CAMERA)” and press it.
4Rotate the MENU/VOLUME wheel # to select
“REC MODE” and press it. The Sub Menu appears.
Select “SP” or “LP” by rotating the MENU/VOLUME
wheel # and press it. Rotate the MENU/VOLUME
wheel # to select “ RETURN”, and press it twice.
The Menu Screen closes.
2Press the MENU/VOLUME wheel # in to access
the Menu Screen.
3Rotate the MENU/VOLUME wheel # to select
“
(CAMERA DISPLAY)” and press it.
4Rotate the MENU/VOLUME wheel # to select
“CLOCK ADJ.”. Press it and “month” is highlighted.
Rotate the MENU/VOLUME wheel # to input the
month. Press it. Repeat to input the day, year, hour and
minute. Rotate the MENU/VOLUME wheel # to select
• “LP” (Long Play) is more economical, providing
1.5 times the recording time.
NOTES:
● If the recording mode is switched during recording, the
playback picture will be blurred at the switching point.
● It is recommended that tapes recorded in the LP mode on
this camcorder be played back on this camcorder.
● During playback of a tape recorded on another
camcorder, blocks of noise may appear or there may be
momentary pauses in the sound.
“
RETURN”, and press it twice. The Menu Screen
closes.
NOTE:
Even if you select “CLOCK ADJ.”, if the parameter is not
highlighted the camcorder’s internal clock continues to
operate. Once you move the highlight bar to the first date/
time parameter (month), the clock stops. When you finish
setting the minute and press the MENU/VOLUME wheel #
in, the date and time begin operation from the date and
time you just set.
EN
GETTING STARTED
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Recording
#
Perform the procedures listed below before continuing.
● Power (੬ pg. 7)
● Grip Adjustment (੬ pg. 8)
● Viewfinder Adjustment (੬ pg. 8)
● Load A Cassette (੬ pg. 9)
● Recording Mode Setting (੬ pg. 10)
1Remove the lens cap.
During shooting
)
2Pull on bottom end t of LCD monitor to open.
3Set the Power Switch r to “ ” or “ ” while
pressing down the Lock Button e located on the
switch.
w
180°
90°
Shooting while using the LCD monitor: Press the
Monitor Open button t and open the LCD monitor
fully.
(
)
CHARGE
OFF
PLAY
Shooting while using the viewfinder: Pull out the
viewfinder fully.
t
e
r
• The POWER/CHARGE lamp w lights and the
camcorder enters the Record-Standby mode.
“PAUSE” ^ is displayed.
• The image will not appear simultaneously on the LCD
monitor and the viewfinder. See “PRIORITY” in the
SYSTEM Menu (੬ pg. 23).
Display
Now
calculating
0
h
25m
1h30m
(
)
1h30m
1h29m
4Press the Recording Start/Stop Button ). “
%, ^ appears and the tally lamp 3 lights while
recording is in progress.
”
Tape remaining time
indicator (Approximate)
0h03m
• To Stop Recording, press the Recording Start/Stop
Button ). The camcorder re-enters the Record-
Standby mode.
0h02m (Blinking)
0h01m (Blinking)
0h00m (Blinking)
To Adjust The Brightness Of The Display
1. Make sure the Power Switch r is set to “ ” and
open the LCD monitor fully, then press the MENU/
VOLUME wheel # in. The Menu Screen appears.
NOTES:
● If the Record-Standby mode continues for 5 minutes, the
camcorder’s power shuts off automatically. To turn the
camcorder on again, push back and pull out the
viewfinder again or close and re-open the LCD monitor.
● When a blank portion is left between recorded scenes on
the tape, the time code is interrupted and errors may
occur when editing the tape. To avoid this, refer to
“RECORDING FROM THE MIDDLE OF A TAPE”
(੬ pg. 13).
2. Rotate the MENU/VOLUME wheel # to select
“
(CAMERA DISPLAY)” and press it.
3. Rotate the MENU/VOLUME wheel # to select
“BRIGHT” and press it. The Menu Screen closes and
the bright level indicator 7 appears on the display.
• To cancel, press the MENU/VOLUME wheel #
again so that the bright level indicator 7 disap-
pears.
● To turn the tally lamp 3 or beep sounds off,
੬ pg. 23.
● When you use the LCD monitor outdoors in direct
sunlight, the LCD monitor may be difficult to see. If this
happens, use the viewfinder instead.
● Black spots or bright spots of light (red, green or blue)
may appear constantly on the LCD monitor or the
viewfinder (੬ pg. 30).
● When the Recording Start/Stop button ) is pressed, it
may take a few seconds before actual recording starts.
4. Rotate the MENU/VOLUME wheel # until the bright
level indicator 7 moves and the appropriate
brightness is reached, then press it. The bright level
indicator 7 disappears.
• It is also possible to adjust the brightness of the
viewfinder by closing the LCD monitor, pulling out
the viewfinder and adjusting as described above.
“
” % starts rotating when the camcorder actually
starts recording.
● The time required to calculate and display the remaining
tape length, and the accuracy of the calculation, may vary
according to the type of tape used.
● “TAPE END” appears when the tape reaches its end, and
the power goes off automatically if left in this condition for
5 minutes. “TAPE END” also appears when a cassette at
its end is loaded.
EN
TAPE RECORDING
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Journalistic Shooting
Zooming
In some situations, different shooting angles may
provide more dramatic results. Hold the camcorder in
the desired position and tilt the LCD monitor in the
most convenient direction. It can rotate 270° (90°
downward, 180° upward).
To produce the zoom in/out effect, or an instantaneous
change in image magnification.
Zoom In
Slide the Power Zoom Lever % towards “T”.
Zoom Out
Slide the Power Zoom Lever % towards “W”.
Self-Recording
Ⅲ The further you slide the Power Zoom Lever %, the
You can shoot yourself while viewing your own image
in the LCD monitor. Open the LCD monitor and tilt it
upward 180° so that it faces forward, then point the
lens toward yourself and start recording.
quicker the zoom action.
NOTES:
● Focusing may become unstable during Zooming. In this
case, set the zoom while in Record-Standby, lock the
focus by using the manual focus (੬ pg. 19), then zoom
in or out in Record mode.
Operation Mode
Choose the appropriate operation mode according to
your preference using the Power Switch r.
● Zooming is possible to a maximum of 700X, or it can be
switched to 16X magnification using the optical zoom
(੬ pg. 21).
● Zoom magnification of over 16X is done through Digital
image processing, and is therefore called Digital Zoom.
● During Digital zoom, the quality of image may suffer.
● Macro shooting (as close as approx. 5 cm (2") to the
subject) is possible when the Power Zoom Lever % is set
all the way to “W”. Also see “TELE MACRO” in the Menu
Screen on page 22.
Power Switch Position
:
Allows you to set various recording functions using the
Menus. If you want more creative capabilities than Full
Auto recording, try this mode.
(Full Auto):
Allows you to record using NO special effects or manual
adjustments. Suitable for standard recording.
%
OFF (CHARGE):
Allows you to switch off the camcorder.
PLAY:
• Allows you to play back a recording on the tape.
• Allows you to transfer footage recorded on the tape to
a computer.
Power-Linked Operation
When the Power Switch r is set to “ ” or “ ”, you can
also turn on/off the camcorder by opening/closing the LCD
monitor or pulling out/pushing in the viewfinder.
r
EN
TAPE RECORDING
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Time Code
Normal Playback
During recording, a time code is recorded on the tape.
This code is to confirm the location of the recorded
scene on the tape during playback.
If recording starts from a blank portion, the time code
begins counting from “00:00:00” (minute:second:frame).
If recording starts from the end of a previously recorded
scene, the time code continues from the last time code
number.
1Load a tape (੬ pg. 9).
2Set the Power Switch r to “PLAY” while pressing
down the Lock Button e located on the switch. To start
playback, press
6
6.
• To stop playback temporarily (Still Playback), press
6
6.
• To stop playback, press 7 4.
• Press 1 5 to rewind, or ¡ 7 to fast-forward the
If during recording a blank portion is left partway
through the tape, the time code is interrupted. When
recording is resumed, the time code starts counting up
again from “00:00:00”. This means the camcorder may
record the same time codes as those existing in a
previously recorded scene. To prevent this, perform
“RECORDING FROM THE MIDDLE OF A TAPE” in the
following cases;
tape during Stop mode.
• High-speed picture search (Shuttle Search) is
possible by pressing 1 5 or ¡ 7 during playback
(holding 1 5 or ¡ 7 down during playback
continues search until released).
• At any time, pressing
6
6 resumes normal
playback.
To Control The Speaker Volume:
• When shooting again after playing back a recorded
tape.
• When power shuts off during shooting.
• When a tape is removed and re-inserted during
shooting.
Rotate the MENU/VOLUME wheel # so that the
volume level indicator i on the display moves to
obtain the appropriate volume.
• When shooting using a partially recorded tape.
• When shooting on a blank portion located partway
through the tape.
• When shooting again after shooting a scene then
opening/closing the cassette holder cover.
ATTENTION
During Shuttle Search, parts
of the picture may not be
clearly visible, particularly on
the left side of the screen.
Display
Minutes
Seconds
6
7
5
4
#
Frames
(30 frames = 1 second)
12 : 34 : 24
Frames are not displayed
during recording.
RECORDING FROM THE MIDDLE OF A TAPE
1Play back a tape or use Blank Search (੬ pg. 14) to
find the spot at which you want to start recording, then
engage the Still Playback mode (੬ pg. 13, “Normal
Playback”).
Speaker
2Set the Power Switch r to “ ” or “ ” while
pressing down the Lock Button e located on the
switch, then start recording.
e
r
NOTES:
● The time code cannot be reset.
● During fast-forwarding and rewinding, the time code
indication does not move smoothly.
Continued on next page.
● The time code is displayed only when “TIME CODE” is
set to “ON” (੬ pg. 24).
EN
TAPE RECORDING
TAPE PLAYBACK
13
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
Blank Search
● If Stop mode continues for 5 minutes when power is
supplied from a battery, the camcorder shuts off
automatically. To turn on again, set the Power Switch r
to “OFF (CHARGE)”, then to “PLAY”.
Helps you find where you should start recording in the
middle of a tape to avoid time code interruption
(੬ pg. 13).
● The playback picture can be viewed in the LCD monitor,
viewfinder or on a connected TV (੬ pg. 15).
● You can also view the playback picture on the LCD
monitor with it flipped over and pushed against the
camera body.
1Load a tape (੬ pg. 9).
2Set the Power Switch r to “PLAY” while pressing
down the Lock Button e located on the switch.
3Press BLANK SEARCH ^.
● LCD monitor/viewfinder indications:
When power is supplied from a battery: the “
”
• “BLANK SEARCH” e appears and the camcorder
automatically starts reverse or forward shuttle search,
then stops at the spot which is about 3 seconds of
tape before the beginning of the detected blank
portion.
battery pack remaining power indicator is displayed.
When power is supplied from an AC outlet: “
not appear.
” does
● When a cable is connected to the AV connector, the
sound is not heard from the speaker.
● If still playback continues for more than about 3 minutes,
the camcorder’s Stop mode is automatically engaged.
To cancel Blank Search midway . . .
..... press 7 4.
● When
6
6 is pressed to engage still playback, the
NOTES:
image may not pause immediately while the camcorder
stabilizes the still image.
● In step 3, if the current position is at a blank portion the
camcorder searches in the reverse direction, and if the
current position is at a recorded portion the camcorder
searches in the forward direction.
● Blank Search does not work if “HEAD CLEANING
REQUIRED. USE CLEANING CASSETTE” has
appeared with the tape.
● If the beginning or end of the tape is reached during
Blank Search, the camcorder stops automatically.
● A blank portion which is shorter than 5 seconds of tape
may not be detected.
● The detected blank portion may be located between
recorded scenes. Before you start recording, make sure
there is no recorded scene after the blank portion.
^
e
r
EN
TAPE PLAYBACK
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
These are some basic types of connections. When
making the connections, refer also to your VCR and TV
instruction manuals.
To AV &
1Make sure all units are turned off.
Connector
cover*
2Connect the camcorder to a TV or VCR as shown
in the illustration.
If using a VCR . . . go to step 3.
If not . . . go to step 4.
To
S-VIDEO *
Audio/Video
3Connect the VCR output to the TV input, referring to
your VCR’s instruction manual.
cable
(provided)
4Turn on the camcorder, the VCR and the TV.
5Set the VCR to its AUX input mode, and set the TV
to its VIDEO mode.
S-Video cable
(optional)
Yellow to
VIDEO IN***
To choose whether or not the following displays
appear on the connected TV . . .
Red to
• Date/Time
AUDIO R IN**
..... set “DATE/TIME” to “AUTO”, “ON” or “OFF” in the
Menu Screen (੬ pg. 23, 34).
• Time Code
..... set “TIME CODE” to “ON” or “OFF” in the Menu
Screen (੬ pg. 24).
White to
AUDIO L IN**
To S-VIDEO IN
• Indications other than date/time and time code
..... set “ON SCREEN” to “LCD”, “LCD/TV” or “OFF” in
the Menu Screen (੬ pg. 23, 24).
To TV or VCR
VCR
TV
NOTES:
● It is recommended to use the AC Adapter as the
power supply instead of the battery pack (੬ pg. 7).
● To monitor the picture and sound from the camcorder
without inserting a tape, set the camcorder’s Power
Switch r to “ ” or “ ”, then set your TV to the
appropriate input mode.
● Make sure you adjust the TV sound volume to its
minimum level to avoid a sudden burst of sound when the
camcorder is turned on.
*
When connecting the cable, open this cover.
** The Audio cable is not required for watching still images
only.
*** Connect when an S-Video cable is not used.
● If you have a TV or speakers that are not specially
shielded, do not place the speakers adjacent to the TV as
interference will occur in the camcorder playback picture.
● While the Audio/Video cable is connected to the AV
connector, sound cannot be heard from the speaker.
EN
TAPE PLAYBACK
15
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
Night-Alive
● Program AE with special effects can be changed during
recording or during Record-Standby.
● Some modes of Program AE special effects cannot be
used during Night-Alive.
Makes dark subjects or areas even brighter than they
would be under good natural lighting. Although the
recorded image is not grainy, it may look as if it is
strobing due to the slow shutter speed.
1Set the Power Switch r to “ ” while pressing
down the Lock Button e located on the switch. Open
the LCD monitor fully or pull out the viewfinder fully.
SHUTTER
1/60: The shutter speed is fixed at 1/60th of a second.
Black bands that usually appear when shooting a TV
screen become narrower.
2Press NIGHT 8 so that the Night-Alive indicator
“
” 2 appears.
1/100: The shutter speed is fixed at 1/100th of a
second. The flickering that occurs when shooting under
a fluorescent light or mercury-vapor lamp is reduced.
• The shutter speed is automatically adjusted to provide
up to 30 times sensitivity.
• “A” appears beside “
being automatically adjusted.
” 2 while the shutter speed is
SPORTS
(Variable Shutter Speed: 1/250 – 1/4000)
To Deactivate Night-Alive . . .
..... press NIGHT 8 again so that the Night-Alive
indicator disappears.
This setting allows fast-moving
images to be captured one frame at
a time, for vivid, stable slow-motion
playback. The faster the shutter
speed, the darker the picture
NOTES:
● During Night-Alive, the following functions or settings
cannot be activated and its indicator blinks or goes out:
• Some modes of “Program AE With Special Effects”
(੬ pg. 16).
becomes. Use the shutter function
under good lighting conditions.
SNOW
• “GAIN UP” in the CAMERA Menu (੬ pg. 22).
• “DIS” in the MANUAL Menu (੬ pg. 22).
● During Night-Alive, it may be difficult to bring the
camcorder into focus. To prevent this, use of manual
focus and/or a tripod is recommended.
Compensates for subjects that may otherwise appear
too dark when shooting in extremely bright surround-
ings such as in the snow.
SPOTLIGHT
Compensates for subjects that may otherwise appear
too bright when shooting under extremely strong direct
lighting such as spotlights.
Program AE With Special Effects
1Set the Power Switch r to “ ” while pressing
down the Lock Button e located on the switch. Open
the LCD monitor fully or pull out the viewfinder fully.
NOTE:
“SPOTLIGHT” has the same effect as –3 with the exposure
control (੬ pg. 19).
2Press the MENU/VOLUME wheel # in. The Menu
Screen appears.
TWILIGHT
3Rotate the MENU/VOLUME wheel # to select
Makes evening scenes look more natural.
“
PROGRAM AE”, then press it.
White Balance (
੬
pg. 20) is initially set to
, but can
be changed to your desired setting. WhenTwilight is
chosen, the camcorder automatically adjusts the focus
from approx. 10 m (32 ft) to infinity. From less than 10 m
(32 ft), adjust the focus manually.
4Rotate the MENU/VOLUME wheel # to select the
desired mode, then press it. Selection is complete.
Press the MENU/VOLUME wheel # in again. The
Menu Screen closes.
SEPIA
• The PROGRAM AE Menu disappears and the
selected mode is activated. The selected mode
indicator appears.
Recorded scenes have a brownish tint like old photos.
Combine this with the Cinema mode for a classic look.
To Deactivate The Selected Mode . . .
..... select “OFF” in step 4.
MONOTONE
Like black and white films, your footage is shot in B/W.
Used together with the Cinema mode, it enhances the
“classic film” effect.
IMPORTANT
Some modes of Program AE with special effects
cannot be used with certain Fade/Wipe Effects
(੬ pg. 17). If an unusable mode is selected, its
indicator blinks or goes out.
CLASSIC FILM
Gives recorded scenes a strobe effect.
STROBE
Your recording looks like a series of consecutive
snapshots.
EN
FOR RECORDING
Download from Www.Somanuals.com. All Manuals Search And Download.
16
FADER — WHITE
Fade/Wipe Effects
Fade in or out with a white screen.
These effects let you make pro-style scene transitions.
Use them to spice up the transition from one scene to
the next.
FADER — BLACK
Fade in or out with a black screen.
Fade or Wipe works when tape recording is started or
when you stop recording.
FADER — B.W
Fade in to a color screen from a black and white
screen, or fade out from color to black and white.
1Set the Power Switch r to “ ” while pressing
down the Lock Button e located on the switch. Open
the LCD monitor fully or pull out the viewfinder fully.
WIPE — CORNER
Wipe in on a black screen from the upper right to the
lower left corner, or wipe out from lower left to upper
right, leaving a black screen.
2Press the MENU/VOLUME wheel # in. The Menu
Screen appears.
3Rotate the MENU/VOLUME wheel # to select
WIPE — WINDOW
“
WIPE/FADER”, then press it.
The scene starts in the center of a black screen and
wipes in toward the corners, or comes in from the
corners, gradually wiping out to the center.
4Rotate the MENU/VOLUME wheel # to select the
desired function, then press it. Selection is complete.
Press the MENU/VOLUME wheel # in again.
• The WIPE/FADER Menu disappears and the effect is
reserved. The indicator representing the selected
effect appears.
WIPE — SLIDE
Wipe in from right to left, or wipe out from left to right.
WIPE — DOOR
5Press the Recording Start/Stop Button ) to activate
Wipe in as the two halves of a black screen open to the
left and right, revealing the scene, or wipe out and the
black screen reappears from left and right to cover the
scene.
the Fade-in/out or Wipe-in/out.
To Deactivate The Selected Effect . . .
..... select “OFF” in step 4.
WIPE — SCROLL
IMPORTANT
The scene wipes in from the bottom to the top of a
black screen, or wipes out from top to bottom, leaving a
black screen.
Some Fade/Wipe Effects cannot be used with certain
modes of Program AE with special effects (੬ pg. 16).
If an unusable Fade/Wipe Effect is selected, its
indicator blinks or goes out.
WIPE — SHUTTER
Wipe in from the center of a black screen toward the
top and bottom, or wipe out from the top and bottom
toward the center leaving a black screen.
NOTE:
You can extend the length of a Fade or Wipe by pressing
and holding the Recording Start/Stop Button ).
#
)
e
r
EN
FOR RECORDING
Download from Www.Somanuals.com. All Manuals Search And Download.
17
NOTES:
Snapshot (For Tape Recording)
● To remove the shutter sound, ੬ “BEEP” on pg. 23.
● If Snapshot recording is not possible, “PHOTO” ^ blinks
when SNAPSHOT $ is pressed.
This feature lets you record still images that look like
photographs onto a tape.
● If Program AE with special effects (੬ pg. 16) is
engaged, certain modes of Program AE with special
effects are disabled during Snapshot recording. In such a
case, the icon blinks.
SNAPSHOT MODE SELECTION
1Set the Power Switch r to “ ” while pressing
down the Lock Button e located on the switch. Open
the LCD monitor fully or pull out the viewfinder fully.
● If SNAPSHOT $ is pressed when “DIS” is set to “ON”
(੬ pg. 22), the Stabilizer will be disabled.
● During playback as well, all Snapshot modes are
available. The shutter sound is not heard.
2Press the MENU/VOLUME wheel # in. The Menu
Screen appears.
● During Snapshot recording, the image displayed in the
viewfinder may be partially missing. However, there is no
effect in the recorded image.
● When a cable is connected to the AV connector, the
shutter sound is not heard from the speaker, however it is
recorded onto the tape.
3Rotate the MENU/VOLUME wheel # to select
“
(CAMERA)”, then press it.
4Rotate the MENU/VOLUME wheel # to select
“SNAP MODE”, then press it.
5Rotate the MENU/VOLUME wheel # to select the
Auto Focus
desired Snapshot mode, then press it.
Rotate the MENU/VOLUME wheel # to select
The camcorder’s Full Range AF system offers
continuous shooting ability from close-up (as close as
approx. 5 cm (2") to the subject) to infinity.
“
RETURN” and press it twice. The Menu Screen
closes.
However, correct focus may not be obtainable in the
situations listed below (in these cases use manual
focusing):
• When two subjects overlap in the same scene.
• When illumination is low.*
• When the subject has no contrast (difference in
brightness and darkness), such as a flat, one-color
wall, or a clear, blue sky.*
FULL
Snapshot mode
with no frame
PIN-UP
Pin-Up mode
FRAME
Snapshot mode
with frame
• When a dark object is barely visible in the viewfinder.*
• When the scene contains minute patterns or identical
patterns that are regularly repeated.
There is the sound effect of a shutter closing.
• When the scene is affected by sunbeams or light
reflecting off the surface of a body of water.
• When shooting a scene with a high-contrast back-
ground.
SNAPSHOT RECORDING
1Press SNAPSHOT $. “PHOTO” ^ appears while
the snapshot is being taken.
* The following low-contrast warnings appear blinking:
If you press during Record-Standby . . .
..... “PHOTO” ^ appears and a still image will be
recorded for approx. 6 seconds, then the
,
,
and
NOTES:
camcorder re-enters the Record-Standby mode.
● If the lens is smeared or blurred, accurate focusing is not
possible. Keep the lens clean, wiping with a piece of soft
cloth if it gets dirty. When condensation occurs, wipe with
a soft cloth or wait for it to dry naturally.
If you press during Recording . . .
..... “PHOTO” ^ appears and a still image will be
recorded for approx. 6 seconds, then the normal
recording resumes.
● When shooting a subject close to the lens, zoom out first
(੬ pg. 12). If zoomed-in in the auto focus mode, the
camcorder may automatically zoom out depending on the
distance between the camcorder and the subject. This will
not occur when “TELE MACRO” (੬ pg. 22) is activated.
• Regardless of the Power Switch r position (“ ” or
“
”), Snapshot recording takes place using the
selected Snapshot mode.
Motor Drive Mode
Keeping SNAPSHOT $ pressed provides an effect
similar to serial photography. (Interval between still
images: approx. 1 second)
EN
FOR RECORDING
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Manual Focus
To obtain correct focus.
Exposure Control
Manual exposure adjustment is recommended in the
following situations:
1If you are using the viewfinder, you should already
have made the necessary viewfinder adjustments
(੬ pg. 8).
• When shooting using reverse lighting or when the
background is too bright.
• When shooting on a reflective natural background
such as at the beach or when skiing.
• When the background is overly dark or the subject
light.
2Set the Power Switch r to “ ” while pressing
down the Lock Button e located on the switch, then
press FOCUS ^ (੬ pgs. 36 and 37). The manual
focus indicator appears.
1Set the Power Switch r to “ ” while pressing
down the Lock Button e located on the switch. Open
the LCD monitor fully or pull out the viewfinder fully.
3To focus on a farther subject, rotate the MENU/
VOLUME wheel # towards “+”. “ ” ) appears and
blinks.
To focus on a nearer subject, rotate the MENU/
VOLUME wheel # towards “–”. “ ” ) appears and
blinks.
2Press the MENU/VOLUME wheel # in. The Menu
Screen appears.
3Rotate the MENU/VOLUME wheel # to select
“
(EXPOSURE)”, then press it.
4Press the MENU/VOLUME wheel # in. Focus
adjustment is complete.
4Rotate the MENU/VOLUME wheel # to select
“MANUAL”, then press it. The Menu Screen disappears.
The exposure control indicator appears.
To reset to Auto Focus, press FOCUS ^ twice or set
the Power Switch r to “ ”.
If FOCUS ^ is pressed once, the camcorder will enter
the focus adjustment mode again.
5Rotate the MENU/VOLUME wheel # towards “+” to
brighten the image, or towards “–” to darken the image.
(maximum 6)
NOTES:
● Be sure to focus the lens in the maximum telephoto
position when you use the Manual Focus mode. If you
focus in on a subject in the wide-angle position, sharply
focused images cannot be obtained when zoomed up
because the depth-of-field is reduced at longer focal
lengths.
6Press the MENU/VOLUME wheel # in. Exposure
adjustment is complete.
To Return To Automatic Exposure Control . . .
..... select “AUTO” in step 4. Or, set the Power Switch
r to “ ”.
● When the focus level cannot be adjusted any further or
closer, “ ” or “ ” will blink.
To Brighten The Subject Quickly . . .
..... press BACKLIGHT 9.
4 is displayed and the
subject is brightened. If pressed again,
4
disappears and the brightness returns to the
previous level.
• +3 exposure has the same effect as the BACKLIGHT
Button 9.
• Using BACKLIGHT 9 may cause the light around the
subject to become too bright and the subject to
become white.
Focus detection zone
• Backlight compensations is also available when the
Power Switch r is set to “ ”.
NOTE:
You cannot use the manual exposure control at the same
time with backlight, spotlight (੬ pg. 16) compensation and
“SNOW” (੬ pg. 16).
While focusing on
a further subject
While focusing on
a nearer subject
EN
FOR RECORDING
Download from Www.Somanuals.com. All Manuals Search And Download.
19
3Rotate the MENU/VOLUME wheel # to select
(W.BALANCE)”, then press it.
Iris Lock
“
Use this function in the following situations:
4Rotate the MENU/VOLUME wheel # to select the
• When shooting a moving subject.
desired mode.
• When the distance to the subject changes (so its size
in the LCD monitor or the viewfinder changes), such
as when the subject is backing away.
• When shooting on a reflective natural background
such as at the beach or when skiing.
• When shooting objects under a spotlight.
• When zooming.
“AUTO”: White balance is adjusted automatically
(factory preset).
“
“
“
“
MWB”: White balance is set manually.
FINE”: Outdoors on a sunny day.
CLOUD”: Outdoors on a cloudy day.
HALOGEN”: A video light or similar type of lighting
When the subject is close, keep the iris locked. Even
when the subject moves away from you, the image will
not darken or brighten.
is used.
5Press the MENU/VOLUME wheel # in. Selection is
complete. Press the MENU/VOLUME wheel # in
again. The Menu Screen closes and the selected mode
indicator except “AUTO” appears.
Before the following steps, perform steps 1
through 4 of “Exposure Control” (੬ pg. 19).
5Adjust zoom so that the subject fills the LCD monitor
or the viewfinder, then press and hold the MENU/
VOLUME wheel # for over 2 seconds. The exposure
control indicator 4 and “ ” 6 appear. Press the
To Return To Automatic White Balance . . .
..... select “AUTO” in step 4. Or, set the Power Switch
r to “ ”.
NOTE:
MENU/VOLUME wheel # in. “ ” 6 changes to “
”
White balance cannot be used when Sepia or Monotone
and the iris is locked.
(੬ pg. 16) is activated.
To Return To Automatic Iris Control . . .
..... rotate the MENU/VOLUME wheel # to display
“AUTO” then press it in step 4. The exposure
Manual White Balance Operation
control indicator 4 and “ ” 6 disappear. Or, set
the Power Switch r to “ ”.
Perform Manual White Balance when shooting under
various types of lighting.
To Lock The Exposure Control And The Iris . . .
..... after step 4 of “Exposure Control” (੬ pg. 19),
adjust the exposure rotating the MENU/VOLUME
wheel #. Then lock the iris in step 5 of “Iris Lock”.
For automatic locking, rotate the MENU/VOLUME
wheel # to select “AUTO”, then press it in step 4.
The iris becomes automatic after about 2 seconds.
1Follow steps 1 through 4 of the white balance
adjustment, and select “
MWB”.
2Hold a sheet of plain white paper in front of the lens.
Adjust zoom or position yourself so that the white paper
fills the screen.
3Press the MENU/VOLUME wheel # in until
Iris
begins blinking rapidly.
Like the pupil of the human eye, it contracts in well-lit
environments to keep too much light from entering, and
dilates in dim environments to allow in more light.
When the setting is completed,
blinking.
resumes normal
4Press the MENU/VOLUME wheel # in twice. The
Menu Screen closes and the Manual White Balance
White Balance Adjustment
indicator
3 is displayed.
A term that refers to the correctness of color
reproduction under various lighting. If the white balance
is correct, all other colors will be accurately
reproduced.
The white balance is usually adjusted automatically.
However, more advanced camcorder operators control
this function manually to achieve a more professional
color/tint reproduction.
NOTES:
● In step 2, it may be difficult to focus on the white paper. In
such a case, adjust focus manually (੬ pg. 19).
● A subject can be shot under various types of lighting
conditions indoors (natural, flourescent, candlelight, etc.).
Because the color temperature is different depending on
the light source, the subject tint will differ depending on
the white balance settings. Use this function for a more
natural result.
1Set the Power Switch r to “ ” while pressing
down the Lock Button e located on the switch. Open
the LCD monitor fully or pull out the viewfinder fully.
● Once you adjust white balance manually, the setting is
retained even if the power is turned off or the battery
removed.
2Press the MENU/VOLUME wheel # in. The Menu
Screen appears.
EN
FOR RECORDING
Download from Www.Somanuals.com. All Manuals Search And Download.
20
WIPE/FADER
Refer to “Fade/Wipe Effects” (੬ pg. 17).
PROGRAM AE
For Recording Menu
This camcorder is equipped with an easy-to-use,
on-screen menu system that simplifies many of the
more detailed camcorder settings (੬ pg. 21 – 24).
Refer to “Program AE With Special Effects” (੬ pg. 16).
EXPOSURE
1Set the Power Switch r to “ ” while pressing
down the Lock Button e located on the switch. Open
the LCD monitor fully or pull out the viewfinder fully.
Refer to “Exposure Control” and “Iris Lock” (੬ pg. 19,
20).
2Press the MENU/VOLUME wheel # in. The Menu
Screen appears.
W.BALANCE
3Rotate the MENU/VOLUME wheel # to select the
desired function menu, and press it.
Refer to “White Balance Adjustment” and “Manual
White Balance Operation” (੬ pg. 20).
4Function menu setting depends on the function.
CAMERA
If you have selected “
WIPE/FADER”,
EXPOSURE” or
“
“
PROGRAM AE”, “
W. BALANCE” . . .
Settings made in the “
effective whether the Power Switch r is set to “ ” or
”. However, the menu settings can be changed only
CAMERA” Menu remain
..... see the column on the right.
If you have selected “ CAMERA”, “
SYSTEM” or “ CAMERA DISPLAY” . . .
..... go to step 5.
“
MANUAL”,
when the Power Switch r is set to “ ”.
“
CAMERA
REC MODE
–
5Rotate the MENU/VOLUME wheel # to select the
desired function and press it. The Sub Menu appears.
Then, rotate the MENU/VOLUME wheel # to select
the parameter, and press it. Selection is complete.
SOUND MODE– 12b i t
ZOOM
SNAP MODE
GA I N UP
–
–
–
40X
FULL
AGC
6Rotate the MENU/VOLUME wheel # to select
“
RETURN” and press it twice. The Menu Screen
RETURN
closes.
• The
icon represents “END”.
REC MODE
NOTE:
Allows you to set the tape recording mode ([SP] or
LP) depending on your preference (੬ pg. 10).
When the Menu Screen is left on for a couple of minutes, a
residual image may be left on the screen and it may take
several seconds for the residual image to disappear. This is
not due to any defect of the unit.
SOUND MODE
[12bit]: Enables tape recording of stereo sound on
four separate channels, and is recommended for use
when performing audio dubbing. (Equivalent to the
32 kHz mode of previous models)
16bit: Enables tape recording of stereo sound on two
separate channels. (Equivalent to the 48 kHz mode of
previous models)
ZOOM
16X: When set to “16X” while using digital zoom, the
zoom magnification will reset to 16X since digital
zoom will be disengaged.
[40X]: Allows you to use the Digital Zoom. By digitally
processing and magnifying images, zooming is
possible from 16X (the optical zoom limit), to a
maximum of 40X digital magnification.
700X: Allows you to use the Digital Zoom. By digitally
processing and magnifying images, zooming is
possible from 16X (the optical zoom limit), to a
maximum of 700X digital magnification.
[ ] = Factory-preset
EN
USING MENUS FOR DETAILED ADJUSTMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
21
SNAP MODE
TELE MACRO
Refer to “Snapshot (For Tape Recording)” (੬ pg. 18).
[OFF]: To turn off this function.
ON: Usually the distance to a subject where the lens
is in focus depends on the zoom magnification.
Unless there is a distance more than 1m (3.3 ft.) to
the subject, the lens is out of focus at the maximum
telephoto setting. When set to “ON”, you can shoot a
subject as large as possible at a distance of approx.
60 cm (2 ft.).
GAIN UP
OFF: Allows you to shoot dark scenes with no picture
brightness adjustment.
[AGC]: The overall appearance may be grainy, but
the image is bright.
AUTO
: The shutter speed is automatically
adjusted (1/30 — 1/200 sec.). Shooting a subject in
low or poor lighting at 1/30 sec. shutter speed
provides a brighter image than in the AGC mode, but
the subject’s movements are not smooth or natural.
The overall appearance may be grainy. While the
• Depending on the zoom position, the lens may go
out of focus.
WIDE MODE
[OFF]: Records with no change in the screen ratio.
For playback on a TV with a normal screen ratio.
shutter speed is being automatically adjusted, “
”
is displayed.
CINEMA
: Inserts black bands at the top and
bottom of the screen. During playback on
wide-screen TVs, the black bands at the top and
bottom of the screen are cut and the screen ratio
MANUAL
The “
MANUAL” settings are effective only when the
Power Switch r is set to “ ”.
becomes 16:9.
@ appears. When using this
mode, refer to your wide-screen TV’s instruction
manual. During playback/recording on 4:3 TVs/LCD
monitor/viewfinder, black bands are inserted at the
top and bottom of the screen and the image appears
like a letterboxed 16:9 movie.
MANUAL
D I S
–
ON
TELE MACRO– OFF
WI DE MODE
WI ND CUT
–
–
OFF
OFF
SQUEEZE
ratio of 16:9. Naturally expands the image to fit the
screen without distortion. @ appears. When
using this mode, refer to your wide-screen TV’s
instruction manual. During playback/recording on 4:3
TVs/LCD monitor/viewfinder, the image is elongated
vertically.
: For playback on TVs with an aspect
RETURN
DIS
OFF: To turn off this function.
WIND CUT
[ON
]: To compensate for unstable images caused
by camera-shake, particularly at high magnification.
[OFF]: Disengages the function which cuts down on
noise created by wind.
NOTES:
ON
: Helps cut down on noise created by wind.
” & appears. The quality of the sound will
● Accurate stabilization may not be possible if hand shake
is excessive, or under the following conditions:
• When shooting subjects with vertical or horizontal
stripes.
“
change. This is normal.
• When shooting dark or dim subjects.
• When shooting subjects with excessive backlighting.
• When shooting scenes with movement in various
directions.
[ ] = Factory-preset
• When shooting scenes with low-contrast backgrounds.
● Switch off this mode when recording with the camcorder
on a tripod.
● The “
cannot be used.
” indicator 8 blinks or goes out if the Stabilizer
EN
USING MENUS FOR DETAILED ADJUSTMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
22
SYSTEM
PRIORITY
[LCD]: When the LCD monitor is fully open, even if
the viewfinder is pulled out, the image is displayed
only on the LCD monitor; it will not be displayed in the
viewfinder.
“
SYSTEM” functions which are set when the Power
Switch r is set to “ ” are also applied when the
Power Switch r is set to “PLAY” (੬ pg. 24).
SYSTEM
FINDER: When the viewfinder is pulled out, even if
the LCD monitor is fully open, the image is displayed
only in the viewfinder; it will not be displayed on the
LCD monitor.
BEEP
–
–
–
–
–
MELODY
ON
TALLY
REMOTE
ON
DEMO MODE
PR I OR I TY
CAM RESET
ON
LCD
CAM RESET
[RETURN]: Does not reset all settings to the
factory-preset.
RETURN
EXECUTE: Resets all settings to the factory-preset.
BEEP
CAMERA DISPLAY
OFF: Even though not heard while shooting, shutter
sound is recorded on the tape.
• Settings made in the “
CAMERA DISPLAY” Menu
are effective only for video shooting.
BEEP: The beep sounds when the power is turned on
or off, and at the beginning and end of recording. Also
to activate the shutter sound effect (੬ pg. 18).
• Settings made in the “
CAMERA DISPLAY” Menu
remain effective even when the Power Switch r is
set to “ ”. However, the menu settings can be
changed only when the Power Switch r is set to
[MELODY]: Instead of a beep, a melody sounds
when any operation is performed. It also activates the
shutter sound effect (੬ pg. 18).
“
”.
CAMERA D I SPLAY
TALLY
BR I GHT
ON SCREEN
DATE / T I ME
T I ME CODE
CLOCK
–
–
–
LCD / TV
AUTO
OFF: The tally lamp remains off at all times.
OFF
[ON]: The tally lamp comes on to signal the start of
recording.
DEC 25 ’03
5 : 30 PM
ADJ .
REMOTE
RETURN
It is recommended that this function be set to “OFF”
to prevent improper operation.
DEMO MODE
BRIGHT
OFF: Automatic demonstration will not take place.
੬ pg. 11, “To Adjust The Brightness Of The Display”
[ON]: Demonstrates certain functions such as
Program AE with special effects, etc., and can be
used to confirm how these functions operate.
Demonstration starts in the following cases:
ON SCREEN
LCD: Keeps the camcorder’s display (except the
date, time and time code) from appearing on the
connected TV screen.
• When the Menu Screen is closed after “DEMO
MODE” is turned “ON”.
• With “DEMO MODE” set to “ON”, if there is no
operation for about 3 minutes after the Power
Switch r is set to “ ” or “ ” .
[LCD/TV]: Makes the camcorder’s display appear on
screen when the camcorder is connected to a TV.
DATE/TIME
OFF: The date/time does not appear.
Performing any operation during the demonstration
stops the demonstration temporarily. If no operation is
performed for more than 3 minutes after that, the
demonstration will resume.
[AUTO]: Displays the date/time for approx. 5
seconds in the following cases:
• When the Power Switch r is set from “OFF
(CHARGE)” to “ ” or “ ”.
NOTES:
• When tape playback starts. The camcorder displays
the date/time when scenes are recorded.
• When the date is changed during tape playback.
● If a tape is in the camcorder, the demonstration cannot be
turned on.
● “DEMO MODE” remains “ON” even if the camcorder
power is turned off.
ON: The date/time is always displayed.
● If “DEMO MODE” remains “ON”, some functions will not
be available. After viewing demo, set to “OFF”.
[ ] = Factory-preset
EN
USING MENUS FOR DETAILED ADJUSTMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
23
TIME CODE
SYSTEM
[OFF]: Time code is not displayed.
SYSTEM
ON: Time code is displayed on the camcorder and on
the connected TV. Frame numbers are not displayed
during recording.
BEEP
–
–
–
–
–
MELODY
TALLY
ON
REMOTE
ON
DEMO MODE
PR I OR I TY
CAM RESET
ON
LCD
CLOCK ADJ.
Allows you to set the current date and time (੬ pg. 10).
RETURN
For Playback Menu
1Set the Power Switch r to “PLAY” while pressing
Each setting is linked with “
appears when the Power Switch r is set to “
(੬ pg. 23).
The parameters are the same as in the description on
pg. 23.
SYSTEM”, which
down the Lock Button e located on the switch.
”
2Press the MENU/VOLUME wheel # in. The Menu
Screen appears.
3Rotate the MENU/VOLUME wheel # to select the
VIDEO DISPLAY
desired function menu, and press it.
• Settings made in the “
effective only for tape playback.
VIDEO DISPLAY” Menu are
4Rotate the MENU/VOLUME wheel # to select the
desired function, and press it to display the Sub Menu.
V I DEO
5Rotate the MENU/VOLUME wheel # to select the
SOUND MODE
12b i t MODE
REC MODE
–
–
–
STEREO
SOUND
desired parameter and press it. Selection is complete.
1
6Rotate the MENU/VOLUME wheel # to select
“
RETURN” and press it twice to close the Menu
Screen.
RETURN
VIDEO
V I DEO
BRIGHT
,
DATE/TIME
,
TIME CODE
SOUND MODE
–
–
–
STEREO
SOUND
12b i t MODE
REC MODE
1
Refer to “
CAMERA DISPLAY” on page 23, 24.
The factory-preset of “DATE/TIME” in the “
DISPLAY” Menu is “OFF”.
VIDEO
ON SCREEN
OFF: Camcorder's display (except the date, time and
time code) is not shown on LCD or connected TV.
[LCD]: Camcorder's display is shown only on LCD
and not on connected TV (except the date, time and
time code).
LCD/TV: Camcorder's display is shown on both LCD
and connected TV.
RETURN
SOUND MODE
12bit MODE
REC MODE
........੬ pg. 25, “Playback Sound”.
........੬ pg. 25, “Playback Sound”.
Allows you to set the tape recording mode ([SP] or
LP) depending on your preference (੬ pg. 10).
It is recommended you use “REC MODE” in the
[ ] = Factory-preset
“
VIDEO” Menu when using this camcorder as a
recorder during dubbing (੬ pg. 27).
• “REC MODE” can be set when the Power Switch r is
set to “PLAY” or “ ” (੬ pg. 21).
EN
USING MENUS FOR DETAILED ADJUSTMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Playback Sound
Display
During tape playback, the camcorder detects the sound
mode in which the recording was made, and plays the
sound back. Select the type of sound to accompany
your playback picture. According to the menu access
explanation on pg. 24, select “SOUND MODE” or “12bit
MODE” from the Menu Screen and set it to the desired
parameter.
12b i
L
t
/ SOUND
1
38
ON SCREEN setting:
For playback sound,
tape speed and tape
running.
SOUND MODE
DATE/TIME setting:
For date/time.
[STEREO
]: Sound is output on both “L” and “R”
channels in stereo.
SOUND L : Sound from the “L” channel is output.
SOUND R : Sound from the “R” channel is output.
DEC 25 ’ 03
5 : 30 PM
12bit MODE
MIX: Original and dubbed sounds are combined and
output in stereo on both “L” and “R” channels.
TIME CODE setting:
For time code.
[SOUND 1]: Original sound is output on both “L” and
“R” channels in stereo.
Minutes
Seconds
SOUND 2: Dubbed sound is output on both “L” and
“R” channels in stereo.
Frames*
12 : 34 : 24
NOTES:
* 30 frames = 1 second
• The camcorder cannot detect the sound mode in which
the recording was made during fast-forward or rewind.
During playback the sound mode is displayed in the upper
left corner.
• The “SOUND MODE” setting is available for both 12-bit
and 16-bit sound. (In previous models’ functions, “12-bit”
is called “32 kHz” and “16-bit” is called “48 kHz”.)
[ ] = Factory-preset
EN
USING MENUS FOR DETAILED ADJUSTMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Dubbing To A VCR
6
To Use This Camcorder As A Player
1Following the illustration, connect the camcorder
and the VCR. Also refer to pg. 15.
2Set the camcorder’s Power Switch r to “PLAY”
while pressing down the Lock Button e located on the
switch, turn on the VCR’s power, and insert the
appropriate cassettes in the camcorder and the VCR.
To AV &
Connector
cover*
3Engage the VCR’s AUX and Record-Pause modes.
4Engage the camcorder’s Play mode to find a spot
just before the edit-in point. Once it is reached, press
£/8 6 on the camcorder.
To
5Press £/8 6 on the camcorder and engage the
Audio/Video
S-VIDEO *
cable
VCR’s Record mode.
(provided)
6Engage the VCR’s Record-Pause mode and press
£/8 6 on the camcorder.
Yellow to
VIDEO** IN
7Repeat steps 4 through 6 for additional editing, then
S-Video cable
(optional)
stop the VCR and camcorder when finished.
Red to
AUDIO R IN
NOTES:
● As the camcorder starts to play your footage it will appear
on your TV. This will confirm the connections and the
AUX channel for dubbing purposes.
● Before you start dubbing, make sure that the indications
do not appear on the connected TV. If they do, they are
being recorded onto the new tape.
White to
AUDIO L IN
To
S-VIDEO IN
To choose whether or not the following displays
appear on the connected TV . . .
TV
VCR
• Date/Time
..... set “DATE/TIME” to “AUTO”, “ON” or “OFF” in the
Menu Screen (੬ pg. 23, 24).
• Time Code
* When connecting the cable, open this cover.
** Connect when an S-Video cable is not used.
..... set “TIME CODE” to “ON” or “OFF” in the Menu
Screen (੬ pg. 24).
• Indications other than date/time and time code
..... set “ON SCREEN” to “LCD”, “LCD/TV” or “OFF” in
the Menu Screen (੬ pg. 23, 24).
EN
DUBBING
Download from Www.Somanuals.com. All Manuals Search And Download.
26
5. Press the Recording Start/Stop button ) to start
recording. % rotates.
Dubbing To Or From A Video Unit
Equipped With A DV Connector
(Digital Dubbing)
6. Press the Recording Start/Stop button ) again to
engage the Record-Pause mode.
rotating.
% stops
It is also possible to copy recorded scenes from this
camcorder onto another video unit equipped with a DV
connector. Since a digital signal is sent, there is little if
any image or sound deterioration.
NOTES:
● Digital Dubbing is performed in the sound mode recorded
on the original tape, regardless of the current “SOUND
MODE” setting (੬ pg. 21).
To Use This Camcorder As A Player
● During Digital Dubbing, incoming signals cannot be
output through the video or audio connectors if they are
copy-guarded.
1Make sure all units are turned off. Connect this
camcorder to a video unit equipped with a DV input
connector using a DV cable as shown in the illustration.
2Set this camcorder’s Power Switch r to “PLAY”
while pressing down the Lock Button e located on the
switch, turn on the video unit’s power, and insert the
appropriate cassettes in this camcorder and the video
unit.
6
)
3Press
£
6 to play back the source tape.
4While watching the playback on the monitor, engage
the DV connector-equipped video unit’s record mode
from the spot on the source tape you want to begin
recording.
To DV 0
NOTES:
● It is recommended to use the AC Adapter as the
power supply instead of the battery pack (੬ pg. 7).
● If the remote control is used when both the player and
recorder are JVC video units, both units will perform the
same operation. To prevent this from happening, press
the buttons on both units.
● If a blank portion or disturbed image is played back on
the player during dubbing, the dubbing may stop so that
an unusual image is not dubbed.
e
(
)
CHARGE
OFF
PLAY
Core filter
DV cable
(optional)
r
Core filter
● Even though the DV cable is connected correctly,
sometimes the image may not appear in step 4. If this
occurs, turn off the power and make connections again.
● If “Snapshot” is attempted during playback, only the
original playback image recorded on the tape is output
from the DV connector 0.
To DV
IN/OUT
Video unit equipped
with DV connector
● When using a DV cable, be sure to use the optional
JVC VC-VDV204U DV cable.
To Use This Camcorder As A Recorder
1. Set this camcorder’s Power Switch r to “PLAY”
while pressing down the Lock Button e located on
the switch.
2. Set “REC MODE” to “SP” or “LP” in the Menu
Screen (੬ pg. 24).
3. Connect the DV cable as shown in the illustration
and load a cassette to record on.
4. Press the Recording Start/Stop button ) to
DV. IN
engage the Record-Pause mode. “
” appears
on the screen.
EN
DUBBING
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Connection To A Personal Computer
It is possible to transfer video to a PC with a DV
connector by using software equipped with the PC or
commercially available software.
1Make sure the camcorder and PC are turned off.
2Connect the camcorder to your PC using the
appropriate cable as shown in the illustration.
3Turn the camcorder’s Power Switch r to “PLAY”
while pressing down the Lock Button e located on the
switch and turn on the PC.
• Refer to the instruction manual of the software on how
to transfer video to the PC.
To DV 0
4When finished, turn off the PC first, then the
camcorder.
Core filter
NOTES:
● It is recommended to use the AC Adapter as the
power supply instead of the battery pack (੬ pg. 7).
● The date/time information cannot be captured into the
PC.
DV cable
(optional)
● Refer to the instruction manuals of the PC and Software.
● The still images can also be transferred to a PC with a DV
connector-equipped capture board.
Core filter
● When using a DV cable, be sure to use the optional
JVC VC-VDV206U or VC-VDV204U DV cable depend-
ing on the type of DV connector (4 or 6 pins) on the
PC.
To DV
connector
● The system may not work properly depending on the PC
or capture board you are using.
● When using the DV connection refer to manufacturer
instructions of your capture board for driver’s installation
and operation instructions.
PC with DV connector
EN
SYSTEM CONNECTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Before consulting your JVC dealer, please check the
following to see if you can correct the problem yourself.
The focus does not adjust automatically.
• Focus is set to the Manual mode.
= Set Focus to the Auto mode (੬ pg. 19).
• The recording was done in a dark place, or the
contrast was low.
• The lens is dirty or covered with condensation.
= Clean the lens and check the focus again
(੬ pg. 34).
The camcorder is a microcomputer-controlled
device. External noise and interference (from a TV,
a radio, etc.) might prevent it from functioning
properly. In such cases, first disconnect its power
supply unit (battery pack, AC Adapter, etc.) and wait
a few minutes; and then re-connect it and proceed
as usual from the beginning.
The cassette will not load properly.
• The cassette is in the wrong position.
= Set it in the right position (੬ pg. 9).
• The battery’s charge is low.
No power is supplied.
• The power is not connected properly.
= Connect the AC Adapter securely (੬ pg. 7).
• The battery is dead.
= Install a fully charged battery (੬ pg. 7, 8).
Snapshot mode cannot be used.
= Replace the dead battery with a fully charged one
(੬ pg. 7, 8).
• The Squeeze mode is selected.
= Disengage the Squeeze mode (੬ pg. 22).
“SET DATE/TIME!” appears.
The color of Snapshot looks strange.
• The date/time is not set.
= Set the date/time (੬ pg. 10).
• The built-in clock battery has run out and the
previously set date/time has been erased.
= Consult your nearest JVC dealer for replacement.
• The light source or the subject does not include white.
Or there are various different light sources behind the
subject.
= Find a white subject and compose your shot so that
it also appears in the frame (੬ pg. 18).
• The Sepia or Monotone mode is activated.
= Turn off Sepia and Monotone (੬ pg. 16).
Recording cannot be performed.
• The tape’s erase protection tab is set to “SAVE”.
= Set the tape’s erase protection tab to “REC”
(੬ pg. 9).
The image taken using Snapshot is too dark.
• Shooting was performed under backlit conditions.
• The Power Switch r is set to “PLAY” or “OFF
= Press the BACKLIGHT Button 9 (੬ pg. 19).
(CHARGE)”.
The image taken using Snapshot is too bright.
• The subject is too bright.
= Set the Power Switch r to “ ” or “ ” (੬ pg. 12).
• “TAPE END” appears.
= Set “PROGRAM AE” to “SPOTLIGHT” in the Menu
Screen (੬ pg. 16).
= Replace with new cassette (੬ pg. 9).
• The cassette holder cover is open.
= Close the cassette holder cover.
Digital Zoom does not work.
• 16X optical zoom is selected.
= Set “ZOOM” to “40X” or “700X” in the Menu Screen
(੬ pg. 21).
There is no picture.
• The camcorder is not getting power, or some other
malfunction exists.
= Turn the camcorder’s power off and on again
(੬ pg. 12).
EN
TROUBLESHOOTING
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Images on the LCD monitor appear dark or
whitish.
The Black & White Fader does not work.
• The Sepia or Monotone mode is activated.
• In places subject to low temperature, images become
dark due to the characteristics of the LCD monitor.
When this happens, the displayed colors differ from
those that are actually recorded. This is not a defect
of the camcorder.
• When the LCD monitor's fluorescent light reaches the
end of its service life, images on the LCD monitor
become dark. Consult your nearest JVC dealer.
= Turn off Sepia and Monotone (੬ pg. 16).
The image looks like the shutter speed is too
slow.
• When shooting in the dark, the unit becomes highly
sensitive to light when “GAIN UP” is set to “AUTO” in
the Menu Screen.
= If you want the lighting to look more natural, set
“GAIN UP” to “AGC” or “OFF” in the Menu Screen
(੬ pg. 22).
= Adjust the brightness and angle of the LCD monitor
(੬ pg. 11).
The rear of the LCD monitor is hot.
White Balance cannot be activated.
• The light used to illuminate the LCD monitor causes it
to become hot.
= Close the LCD monitor to turn it off or set the Power
Switch r to “OFF (CHARGE)”, and let the unit cool
down.
• The Sepia or Monotone mode is activated.
= Turn off Sepia or Monotone before setting White
Balance (੬ pg. 16, 20).
When shooting a subject illuminated by bright
light, vertical lines appear.
• This is a result of exceedingly high contrast, and is
not a malfunction.
The indicators and the image color on the
LCD monitor are not clear.
• This may occur when the surface or the edge of the
LCD monitor is pressed.
When the screen is under direct sunlight
during shooting, the screen becomes red or
black for an instant.
The LCD monitor or viewfinder indications
blink.
• This is not a malfunction.
• Certain Fade/Wipe effects, certain modes of Program
AE with special effects, “DIS” and other functions that
cannot be used together are selected at the same
time.
= Re-read the sections covering Fade/Wipe effects,
Program AE with special effects and “DIS”
(੬ pg. 16, 17, 22).
The date/time does not appear.
• “DATE/TIME” is set to “OFF” in the Menu Screen.
= Set “DATE/TIME” to “ON” in the Menu Screen
(੬ pg. 23, 24).
Time code does not appear.
• “TIME CODE” is set to “OFF” in the Menu Screen.
= Set “TIME CODE” to “ON” in the Menu Screen
(੬ pg. 24).
Colored bright spots appear all over the LCD
monitor or the viewfinder.
• The LCD monitor and the viewfinder are made with
high-precision technology. However, black spots or
bright spots of light (red, green or blue) may appear
constantly on the LCD monitor or the viewfinder.
These spots are not recorded on the tape. This is not
due to any defect of the unit. (Effective dots: more
than 99.99 %)
During recording, sound cannot be heard.
• This is normal.
Play, Rewind and Fast-Forward functions do
not work.
• The Power Switch r is set to “ ” or “ ”.
= Set the Power Switch r to “PLAY” (੬ pg. 13).
EN
TROUBLESHOOTING
Download from Www.Somanuals.com. All Manuals Search And Download.
30
The charger indicator on the camcorder does
not light.
• The temperature of the battery is extremely high/low.
• Charging is difficult in places subject to extremely
high/low temperatures.
= To protect the battery, it is recommended to charge
it in places with a temperature of 10°C to 35°C
(50°F to 95°F) (੬ pg. 32).
The LCD monitor image is distorted.
• During playback of the unrecorded portion,
High-speed Search and still playback, LCD monitor
indications appear distorted. This is not a defect.
Images on the LCD monitor are jittery.
• The speaker volume is too great.
= Turn the speaker volume down (੬ pg. 13).
Blocks of noise appear during playback, or
there is no playback picture and the screen
becomes blue.
When the image is printed from the printer, a
black bar appears at the bottom of the screen.
• This is not a malfunction.
= Clean the video heads with an optional cleaning
cassette (੬ pg. 33).
= By recording with “DIS” activated (੬ pg. 22) this
can be avoided.
The LCD monitor, the viewfinder and the lens
have become dirty (ex. fingerprints).
When the camcorder is connected via the DV
connector, the camcorder does not operate.
= Wipe them gently with soft cloth. Wiping strongly
can cause damage (੬ pg. 34).
• The DV cable was plugged/unplugged with power
turned on.
= Turn the camcorder’s power off and on again, then
operate it.
An unusual mark appears.
= Check the section of the manual that explains LCD
monitor/viewfinder indications (੬ pg. 36 – 38).
An error indication (E01, E02 or E06) appears.
• A malfunction of some kind has occurred. In this case
the camcorder’s functions become unusable.
= Remove the power supply (battery pack, etc.) and
wait a few minutes for the indication to clear. When
it does, you can resume using the camcorder. If the
indication remains even though you repeat the
above two or three times, please consult your
nearest JVC dealer. Do not eject the cassette. This
will cause damage to the tape.
An error indication (E03 or E04) appears.
• A malfunction of some kind has occurred. In this case
the camcorder’s functions become unusable.
= Eject the cassette once and re-insert it, then check if
the indication clears. When it does, you can resume
using the camcorder. If the indication remains even
though you repeat the above two or three times,
please consult your nearest JVC dealer.
EN
TROUBLESHOOTING
Download from Www.Somanuals.com. All Manuals Search And Download.
31
NOTES:
AC Adapter
● It is normal for the battery pack to be warm after
charging, or after use.
Temperature Range Specifications
When using the AC Adapter in areas other than
the USA
Charging ................ 10°C to 35°C (50°F to 95°F)
Operation ............... 0°C to 40°C (32°F to 104°F)
Storage .................. –10°C to 30°C (14°F to 86°F)
Ⅲ The provided AC Adapter features automatic voltage
selection in the AC range from 110 V to 240 V.
● Recharging time is based on room temperature of 20°C
(68°F).
● The lower the temperature, the longer recharging takes.
USING HOUSEHOLD AC PLUG ADAPTER
In case of connecting the unit’s power cord to an AC
wall outlet other than American National Standard C73
series type use an AC plug adapter, called a “Siemens
Plug”, as shown.
Cassettes
For this AC plug adapter, consult your nearest JVC
dealer.
To properly use and store your cassettes, be sure to
read the following cautions:
1. During use . . .
Plug adapter
... make sure the cassette bears the Mini DV mark.
... be aware that recording onto prerecorded tapes
automatically erases the previously recorded
video and audio signals.
... make sure the cassette is positioned properly
when inserting.
Ⅲ If there is dust or dirt on the AC Adapter, wipe it
clean before using.
... do not load and unload the cassette repeatedly
without allowing the tape to run at all. This
slackens the tape and can result in damage.
... do not open the front tape cover. This exposes the
tape to fingerprints and dust.
2. Store cassettes . . .
... away from heaters or other heat sources.
... out of direct sunlight.
... where they won’t be subject to unnecessary shock
or vibration.
... where they won’t be exposed to strong magnetic
fields (such as those generated by motors,
transformers or magnets).
Battery Packs
The supplied battery pack is a
lithium-ion battery. Before using
the supplied battery pack or an
optional battery pack, be sure to
read the following cautions:
1. To avoid hazards . . .
Terminals
... do not burn.
... do not short-circuit the terminals. When
transporting, make sure the provided battery cap
is attached to the battery. If the battery cap is
misplaced, carry the battery in a plastic bag.
... do not modify or disassemble.
... vertically, in their original cases.
... do not expose the battery to temperatures
exceeding 60°C (140°F), as this may cause the
battery to overheat, explode or catch fire.
... use only specified chargers.
LCD Monitor
1. To prevent damage to the LCD monitor,
DO NOT . . .
2. To prevent damage and prolong service life . . .
... do not subject to unnecessary shock.
... charge in an environment where temperatures are
within the tolerances shown in the following chart.
This is a chemical reaction type battery—cooler
temperatures impede chemical reaction, while
warmer temperatures can prevent complete
charging.
... store in a cool, dry place. Extended exposure to
high temperatures will increase natural discharge
and shorten service life.
... fully charge and then fully discharge the battery
every 6 months when storing the battery pack
over a long period time.
... push it strongly or apply any shocks.
... place the camcorder with the LCD monitor on the
bottom.
2. To prolong service life . . .
... avoid rubbing it with coarse cloth.
3. Be aware of the following phenomena for LCD
monitor use.
These are not malfunctions:
• While using the camcorder, the surface around the
LCD monitor and/or the back of the LCD monitor
may heat up.
• If you leave power on for a long time, the surface
around the LCD monitor becomes hot.
... remove from charger or powered unit when not in
use, as some machines use current even when
switched off.
EN
CAUTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
32
5. Dirty heads can cause the following problems:
Main Unit
1. For safety, DO NOT . . .
... open the camcorder’s chassis.
... disassemble or modify the unit.
... short-circuit the terminals of the battery pack.
Keep it away from metallic objects when not in
use.
... allow inflammables, water or metallic objects to
enter the unit.
... remove the battery pack or disconnect the power
supply while the power is on.
... leave the battery pack attached when the
camcorder is not in use.
2. Avoid using the unit . . .
• No picture during playback.
• Blocks of noise appear during playback.
• During recording or playback, the Head Clog
Warning indicator “ ” appears.
• Recording cannot be performed properly.
... in places subject to excessive humidity or dust.
... in places subject to soot or steam such as near a
cooking stove.
... in places subject to excessive shock or vibration.
... near a television set.
... near appliances generating strong magnetic or
electric fields (speakers, broadcasting antennas,
etc.).
In such cases, use an optional cleaning cassette.
Insert it and play back. If the cassette is used more
than once consecutively, damage to the video heads
may result. After the camcorder plays back for about
20 seconds, it stops automatically. Also refer to the
cleaning cassette’s instructions.
If, after using the cleaning cassette, the problems
still exist, consult your nearest JVC dealer.
... in places subject to extremely high (over 40°C or
104°F) or extremely low (under 0°C or 32°F)
temperatures.
3. DO NOT leave the unit . . .
... in places of over 50°C (122°F).
... in places where humidity is extremely low (below
35%) or extremely high (above 80%).
... in direct sunlight.
Mechanical moving parts used to move the video
heads and video tape tend to become dirty and worn
out over time. In order to maintain a clear picture at
all times, periodic check-ups are recommended after
using the unit for about 1,000 hours. For periodic
check-ups please consult your nearest JVC dealer.
... in a closed car in summer.
... near a heater.
4. To protect the unit, DO NOT . . .
... allow it to become wet.
... drop the unit or strike it against hard objects.
... subject it to shock or excessive vibration during
transportation.
... keep the lens directed at extremely bright objects
for long periods.
About moisture condensation . . .
● You have observed that pouring a cold liquid into a
glass will cause drops of water to form on the glass
outer surface. This same phenomenon occurs on the
head drum of a camcorder when it is moved from a
cool place to a warm place, after heating a cold room,
under extremely humid conditions or in a place directly
subjected to the cool air from an air conditioner.
● Moisture on the head drum can cause severe
damage to the video tape, and can lead to internal
damage to the camcorder itself.
... expose the lens to direct sunlight.
... carry it by holding the LCD monitor or the
viewfinder.
... swing it excessively when using the shoulder strap
or the grip.
Serious malfunctioning
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC dealer.
The camcorder is a microcomputer-controlled
device. External noise and interference (from a TV,
a radio, etc.) might prevent it from functioning
properly. In such cases, first disconnect its power
supply unit (battery pack, AC Adapter, etc.) and wait
a few minutes and then re-connect it and proceed
as usual from the beginning.
EN
CAUTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
33
For Your Maintenance
1) After Use
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
1. Turn off the camcorder.
2. Slide and hold OPEN/EJECT o in the direction
of the arrow, then pull the cassette holder cover
open until it locks. The cassette holder opens
automatically. Remove the cassette.
Change or modifications not approved by the party
responsible for compliance could void the user’s
authority to operate the equipment. This equipment
has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
3. Press “PUSH HERE” to close the cassette holder.
• Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely
before closing the cassette holder cover.
4. Tilt the viewfinder upward. Press BATT.
RELEASE i and remove the battery pack.
2) Cleaning The Camcorder
1. To clean the exterior, wipe gently with a soft cloth.
Put the cloth in diluted mild soap and wring it well
to wipe off heavy dirt. Then wipe again with a dry
cloth.
2. Open the LCD monitor. Wipe gently with a soft
cloth. Be careful not to damage the monitor.
Close the LCD monitor.
3. To clean the lens, blow it with a blower brush,
then wipe gently with lens cleaning paper.
NOTES:
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
● Avoid using strong cleaning agents such as benzine or
alcohol.
● Cleaning should be done only after the battery pack has
been removed or other power units have been
disconnected.
● Mold may form if the lens is left dirty.
● When using a cleaner or chemically treated cloth refer to
the cautions of each product.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme
à la norme NMB-003 du Canada.
EN
CAUTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
34
Connectors
Camcorder
S-Video
Output
General
: Y : 1 V (p-p), 75 Ω, analog
C : 0.29 V (p-p), 75 Ω, analog
Power supply
:
DC 11.0 V
DC 7.2 V
(Using AC Adapter)
(Using battery pack)
AV
Power consumption
LCD monitor off,
viewfinder on : Approx. 3.4 W
LCD monitor on,
viewfinder off : Approx. 4.7 W
Dimensions
(W x H x D)
Video output
Audio output
: 1 V (p-p), 75 Ω, analog
: 300 mV (rms), 1 kΩ, analog,
stereo
DV
Output
Input
: 4-pin, IEEE 1394 compliant
: 4-pin, IEEE 1394 compliant
: 69 mm x 94 mm x 143 mm
(2-3/4” x 3-3/4” x 5-11/16”)
(with the LCD monitor closed and
the viewfinder pushed back in)
AC Adapter
Weight
Operating
temperature
Operating
humidity
: Approx. 525 g (1.2 lbs)
: 0°C to 40°C (32°F to 104°F)
: 35% to 80%
Power requirement
U.S.A. and
Canada
Other countries : AC 110 V to 240 V~, 50 Hz/60 Hz
Output : DC 11 V , 1 A
:
AC 120 Vg, 60 Hz
Storage
temperature
Pickup
Lens
: –20°C to 50°C (–4°F to 122°F)
: 1/6" CCD
: F 1.6, f = 2.7 mm to 43.2 mm,
16:1 power zoom lens
Filter diameter
LCD monitor
: ø37 mm
: 2.5" diagonally measured, LCD
panel/TFT active matrix system
Viewfinder
Speaker
: Electronic viewfinder with 0.24"
color LCD
: Monaural
Digital Video Camera
Format
Signal format
Recording/
: DV format (SD mode)
: NTSC standard
Playback format : Video: Digital component
recording
: Audio: PCM digital recording,
32 kHz 4-channel (12-bit),
48 kHz 2-channel (16-bit)
Cassette
: Mini DV cassette
Tape speed
: SP : 18.8 mm/s
LP : 12.5 mm/s
Maximum
recording time : SP : 80 min.
(using 80 min.
cassette)
LP : 120 min.
Specifications shown are for SP mode unless otherwise indicated. E & O.E. Design and specifications subject
to change without notice.
EN
SPECIFICATIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Controls, Connectors And Indicators
Refer to this diagram while reading the instructions.
1
4 5 6 7
LCD monitor
Stereo
microphone
2
3
8 9 0
!
@
Viewfinder
Speaker
# $ %
^ &
*
(
y u
t
)
q
i
r
w
e
o
(
)
CHARGE
OFF
PLAY
LCD Monitor/Viewfinder Indications
During Tape Recording
During Tape Playback
0
9
!
@
#
$
w
e
r
t
1h50m
12b i t
L
/
SOUND1
1
83
40
x
W
T
%
&
REC
2
3
5
7
8
^
*
BLANK SEARCH
4
6
3
SOUND 12b i t
15 : 55
VOLUME
y
DEC 25 ’ 03
10 : 00 AM
DEC 25 ’ 03
10 : 00 AM
116 : 21 : 24
q
)
(
o
i
u
EN
INDEX
Download from Www.Somanuals.com. All Manuals Search And Download.
36
5 Displays the selected Program AE with special
effects ........................................................ ੬ pg. 16
1 Camera Sensor
Be careful not to cover this area, a sensor neces-
sary for shooting is built-in here.
6 Appears when the iris is locked ................. ੬ pg. 20
2 Grip Strap .................................................... ੬ pg. 8
3 Tally Lamp ........................................... ੬ pg. 11, 23
4 Stop Button [7] .......................................... ੬ pg. 13
5 Rewind Button [1] .................................. ੬ pg. 13
7 • SOUND : Displays the sound mode for approx.
5 seconds after turning on the
camcorder .............................. ੬ pg. 21
• BRIGHT : Displays the brightness of the
LCD monitor ........................... ੬ pg. 11
6 Play/Pause Button [3/ ]........................... ੬ pg. 13
8
8 Appears when Digital Image Stabilizer (“DIS”) is
engaged .................................................... ੬ pg. 22
9 Approximate zoom ratio: Appears during zooming
.................................................................. ੬ pg. 12
7 Fast-Forward Button [¡] ......................... ੬ pg. 13
8 NIGHT Button ............................................ ੬ pg. 16
9 BACKLIGHT Button................................... ੬ pg. 19
0 Digital Video Connector [DV] (i.Link*) ... ੬ pg. 27, 28
0 Appears during zooming
Zoom level indicator ............................ ੬ pg. 12
*
i.Link refers to the IEEE1394-1995 industry
specification and extensions thereof. The
logo is
! Displays the selected Fade/Wipe effect .... ੬ pg. 17
@ Appears when in the Squeeze or Cinema mode
.................................................................. ੬ pg. 22
used for products compliant with the i.Link standard.
! Battery Pack Mount ..................................... ੬ pg. 7
@ DC Input Connector .................................... ੬ pg. 7
# • MENU Wheel [+, –] ................................. ੬ pg. 21
• Speaker Volume Control [VOLUME] ....... ੬ pg. 13
$ Snapshot Button [SNAPSHOT] ................. ੬ pg. 18
% Power Zoom Lever [T/W] .......................... ੬ pg. 12
^ • FOCUS Button ........................................ ੬ pg. 19
• BLANK SEARCH Button ......................... ੬ pg. 14
# Displays the recording mode (SP or LP) ... ੬ pg. 10
$ Displays the tape remaining time .............. ੬ pg. 11
% Rotates while the tape is running .............. ੬ pg. 11
^ • “REC” appears during recording
• “PAUSE” appears during Record-Standby mode
................................................................ ੬ pg. 11
• “PHOTO” appears when taking a Snapshot
................................................................ ੬ pg. 18
& Audio/Video Output Connector [AV] .... ੬ pg. 15, 26
* S-Video Output Connector
[S-VIDEO] ........................................... ੬ pg. 15, 26
& Appears when the wind cut mode is engaged to cut
down on noise created by wind ................. ੬ pg. 22
* Displays the battery remaining power level
( Diopter Adjustment Control ......................... ੬ pg. 8
) Recording Start/Stop Button ..................... ੬ pg. 11
q Shoulder Strap Eyelets ............................... ੬ pg. 9
w POWER/CHARGE Lamp ................ ੬ pg. 7, 11, 12
e Lock Button ............................................... ੬ pg. 12
r Power Switch
.................................................................. ੬ pg. 38
( Displays the date/time ................... ੬ pg. 10, 23, 25
) Appears when the focus is adjusted manually
............................................................ ੬ pg. 18, 19
q Displays the Time Code ...................... ੬ pg. 13, 24
w Displays the sound mode .................... ੬ pg. 24, 25
e Displays the Blank Search mode .............. ੬ pg. 14
r Displays the tape speed ............................ ੬ pg. 10
t Appears while a tape is running
[
,
, PLAY, OFF (CHARGE)] .............. ੬ pg. 12
t Monitor Latch ............................................ ੬ pg. 11
y Stud Hole .................................................... ੬ pg. 9
u Tripod Mounting Socket .............................. ੬ pg. 9
i Battery Release Button [BATT. RELEASE] .... ੬ pg. 7
o OPEN/EJECT Switch .................................. ੬ pg. 9
3
: Playback
¡
1
8
: Fast-Forward/Shuttle Search
: Rewind/Shuttle Search
: Pause
The connector * is located beneath a cover.
y Displays the battery remaining power level
.................................................................. ੬ pg. 38
1 Appears when the Power Switch is set to “
”
u Displays the date/time ................... ੬ pg. 23, 24, 25
.................................................................. ੬ pg. 12
i • BRIGHT : Displays the brightness of the LCD
2 •
: Appears when Night-Alive is engaged
..................................................... ੬ pg. 16
monitor ................................ ੬ pg. 11
• VOLUME : Displays the speaker volume
•
: Appears when “GAIN UP” is set to “AUTO”
and the shutter speed is being automati-
cally adjusted................................ ੬ pg. 22
............................................ ੬ pg. 13
The level indicator moves.
o Displays the time code ........................ ੬ pg. 24, 25
3 Appears when the white balance is adjusted
.................................................................. ੬ pg. 20
4 • “ؓ” : Appears when the exposure is adjusted
..................................................... ੬ pg. 19
•
: Appears when backlight compensation is
used.............................................. ੬ pg. 19
EN
INDEX
Download from Www.Somanuals.com. All Manuals Search And Download.
37
WARNING INDICATIONS
(high)
E01, E02 or E06 UNIT IN SAFEGUARD MODE
REMOVE AND REATTACH BATTERY
(exhausted)
The error indications (E01, E02 or E06) show what type
of malfunction has occured. When an error indication
appears, the camcorder turns off automatically.
Remove the power supply (battery, etc.) and wait a few
minutes for the indication to clear. When it does, you
can resume using the camcorder. If the indication
remains, consult your nearest JVC dealer.
Displays the battery remaining power level. As the
battery power comes close to nil, the battery indicator
blinks (battery power warning). When the battery
power is exhausted, power turns off automatically.
Appears when no tape is loaded.
(੬ pg. 9)
E03 or E04 UNIT IN SAFEGUARD MODE EJECT
AND REINSERT TAPE
CHECK TAPE’S ERASE PROTECTION TAB
Appears when the erase protection tab is set to “SAVE”
while the Power Switch r is set to “ ” or “ ”.
(੬ pg. 9)
The error indications (E03 or E04) show what type of
malfunction has occured. When an error indication
appears, the camcorder turns off automatically. Eject
the cassette once and re-insert it, then check if the
indication clears. When it does, you can resume using
the camcorder. If the indication remains, consult your
nearest JVC dealer.
HEAD CLEANING REQUIRED USE CLEANING
CASSETTE
Appears if dirt is detected on the heads during
recording or playback. Use an optional cleaning
cassette.
CONDENSATION, OPERATION PAUSED
PLEASE WAIT
(੬ pg. 33)
Appears if condensation occurs. When this indication is
displayed, wait more than 1 hour until condensation
disappears.
TAPE!
Appears if a tape is not loaded when the Recording
Start/Stop Button ) or SNAPSHOT Button $ is
pressed while the Power Switch r is set to “ ” or
“
”.
TAPE END
Appears when the tape ends during recording or
playback.
SET DATE/TIME!
• Appears when the date/time is not set.
(੬ pg. 10)
• Appears when the built-in clock battery runs out and
the previously set date/time is erased. Consult your
nearest JVC dealer for replacement.
LENS CAP
Appears for 5 seconds after power is turned on if the
lens cap is attached.
EN
INDEX
Download from Www.Somanuals.com. All Manuals Search And Download.
38
A
I
AC Adapter................................................... ੬ pg. 7, 8
Auto Date ....................................................... ੬ pg. 23
Auto Focus ..................................................... ੬ pg. 18
Auto Shut off ............................................ ੬ pg. 11, 14
Icons ...................................................... ੬ pg. 21 – 25
Iris .................................................................. ੬ pg. 20
Iris Lock .......................................................... ੬ pg. 20
J
B
Journalistic Shooting ...................................... ੬ pg. 12
Backlight Compensation ................................ ੬ pg. 19
Battery Low .................................................... ੬ pg. 38
Battery Pack ........................................... ੬ pg. 7, 8, 32
Beep............................................................... ੬ pg. 23
Blank Search.................................................. ੬ pg. 14
Brighten The LCD Monitor ............................. ੬ pg. 11
L
LCD monitor/Viewfinder Indications ....... ੬ pg. 36 – 38
Load A Tape ..................................................... ੬ pg. 9
M
Maintenance .................................................. ੬ pg. 34
Manual Focus................................................. ੬ pg. 19
Menu Screen, CAMERA .......................... ੬ pg. 21, 22
Menu Screen, CAMERA DISPLAY .......... ੬ pg. 23, 24
Menu Screen, MANUAL ................................. ੬ pg. 22
Menu Screen, SYSTEM ................................. ੬ pg. 23
Menu Screen, VIDEO ..................................... ੬ pg. 24
Menu Screen, VIDEO DISPLAY ..................... ੬ pg. 24
Monotone ....................................................... ੬ pg. 16
Motor Drive Mode .......................................... ੬ pg. 18
C
Channels (Left/Right) ..................................... ੬ pg. 25
Charge The Battery Pack ................................. ੬ pg. 7
Cinema........................................................... ੬ pg. 22
Classic Film.................................................... ੬ pg. 16
Clean The Camcorder .................................... ੬ pg. 34
Connections ................................. ੬ pg. 7, 15, 26 – 28
D
Darken The LCD Monitor ............................... ੬ pg. 11
Date/Time Display .................................. ੬ pg. 23 – 25
Date/Time Settings ........................................ ੬ pg. 10
Demonstration Mode .................................. ੬ pg. 6, 23
Digital Zoom ............................................. ੬ pg. 12, 21
DIS (Digital Image Stabilizer) ......................... ੬ pg. 22
Diopter Adjustment .......................................... ੬ pg. 8
Dubbing .................................................... ੬ pg. 26, 27
N
Night-Alive ...................................................... ੬ pg. 16
P
Power-Linked Operation................................. ੬ pg. 12
Power Switch Position .................................... ੬ pg. 12
Program AE With Special Effects ................... ੬ pg. 16
Provided Accessories ...................................... ੬ pg. 5
E
R
Erase Protection .............................................. ੬ pg. 9
Exposure Control ........................................... ੬ pg. 19
Record-Standby ............................................. ੬ pg. 12
Recording Mode............................................. ੬ pg. 10
Reset.............................................................. ੬ pg. 23
Rewind The Tape ........................................... ੬ pg. 13
F
Fade-In/Out .................................................... ੬ pg. 17
Fast-Forward The Tape .................................. ੬ pg. 13
G
Gain Up .......................................................... ੬ pg. 22
Grip Adjustment ............................................... ੬ pg. 8
EN
TERMS
Download from Www.Somanuals.com. All Manuals Search And Download.
39
S
T
Self-Recording ............................................... ੬ pg. 12
Sepia .............................................................. ੬ pg. 16
Shuttle Search ............................................... ੬ pg. 13
Shutter Speed ................................................ ੬ pg. 16
Snapshot ........................................................ ੬ pg. 18
Snapshot Mode .............................................. ੬ pg. 18
Snow .............................................................. ੬ pg. 16
Sound Mode ....................................... ੬ pg. 21, 24, 25
Speaker Volume ............................................. ੬ pg. 13
Specifications ................................................. ੬ pg. 35
Sports ............................................................ ੬ pg. 16
Spotlight ......................................................... ੬ pg. 16
Squeeze ......................................................... ੬ pg. 22
Still Playback .................................................. ੬ pg. 13
Strobe ............................................................ ੬ pg. 16
Tally ................................................................ ੬ pg. 23
Tele Macro ..................................................... ੬ pg. 22
Time Code.......................................... ੬ pg. 13, 24, 25
Tripod Mounting ............................................... ੬ pg. 9
Twilight ........................................................... ੬ pg. 16
U
Unload A Tape .................................................. ੬ pg. 9
W
White Balance ................................................ ੬ pg. 20
Wide Mode ..................................................... ੬ pg. 22
Wind Cut ........................................................ ੬ pg. 22
Wipe In/Out .................................................... ੬ pg. 17
Z
Zooming ......................................................... ੬ pg. 12
VICTOR COMPANY OF JAPAN, LIMITED
Printed in Malaysia
1203-HO-OT-VM
US
COPYRIGHT© 2003 VICTOR COMPANY OF JAPAN, LTD.
Download from Www.Somanuals.com. All Manuals Search And Download.
|