DVD PLAYER
Hi-Fi VIDEO
CASSETTE
RECORDER
USER’S GUIDE
For model:
HR-XV1EU
DIGITAL VIDEO
LPT0715-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
For ItaIy:
“It is declared that this product, brand JVC, conforms to the Ministry Decree n. 548 of 28 Aug.’95 published in
the Official Gazette of the Italian Republic n. 301 of 28 Dec.’95”
The STANDBY/ON
button does not completely shut off mains power from the unit, but switches operating
current on and off. “ ” shows electrical power standby and “ I ” shows ON.
Video tapes recorded with this video recorder in the LP (Long Play) mode cannot be played back on a single-
speed video recorder.
When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow
for ventilation (10 cm or more on both sides, on top and at the rear.)
When discarding batteries, environmental problems must be considered and the local rules or laws governing
the disposal of these batteries must be followed strictly.
Failure to heed the following precautions may result in damage to the recorder, remote control or video
cassette.
1. DO NOT place the recorder ...
... in an environment prone to extreme temperatures or humidity.
... in direct sunlight.
... in a dusty environment.
... in an environment where strong magnetic fields are generated.
... on a surface that is unstable or subject to vibration.
2. DO NOT block the recorder’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get
out.)
3. DO NOT place heavy objects on the recorder or remote control.
4. DO NOT place anything which might spill on top of the recorder or remote control.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
5. DO NOT expose the apparatus to dripping or splashing.
6. DO NOT use this equipment in a bathroom or places with water. Also DO NOT place any containers filled
with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups, etc.) on top of this
unit.
7. DO NOT place any naked flame sources, such as lighted candles, on the apparatus.
8. AVOID violent shocks to the recorder during transport.
MOISTURE CONDENSATION
Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or under
extremely humid conditions-just as water droplets form in the surface of a glass filled with cold liquid. Moisture
condensation on the head drum will cause damage to the tape. In conditions where condensation may occur,
keep the recorder turned on for a few hours to let the moisture dry.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Video Cassette Recorder
• Repeat/Scene Repeat
• On-Screen Display in 3
Languages
• High Quality (HQ) Images
• On-Screen Displays (OSD)
• Nicam Hi-Fi Stereo Audio
Recording and Playback
• ATS- Automatic Tuning System
• CATV Tuner with Hyperband
• 80 Memories for presets
• Auto Time Setting
• 30 Minutes Back-Up in case of
Power failure
• 6 rotary Heads (4 Video Heads
2 HiFi Audio Heads)
• Long play
• AV-Front input jacks
• 2 Scart sockets for Premiere
• CE Symbol guaranteeing
Compliance to Currently
Effective European Standards
DVD Player
• Digital Audio Jack (Coaxial)
• Multi-Language
• Multi-Angle
• Surround audio
• Repeat Playback
• Memory/Random Playback
• Zoom
• Video Aspect Ratio
• Parental Control
• VPS/PDC system
• Timer Recording of up to 8
Programs per Month
®
• SHOWVIEW -rapid timer
programing
• 3 Scenes memory
• Instant Timer Recording (ITR)
• Video index Search System
• Slow Motion
• NTSC Video Cassette Tape
Playback on PAL TV
• Real-Time Tape Counter with
ZERO RETURN-Function
• Digital AUTO Tracking (ATR
Function)
• Digital (Optical or Coaxial) output
for Dolby Digital (AC-3) and DTS
• Playback of DVD, Video-CD and
Audio-CD
• PAL & NTSC DVDs playback
• A-B Repeat playback
• MP3 CD playback
* This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use
of this copyright protection technology must be authorized by Macrovision Corporation or other rights owners
and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation or other rights owners. Reverse engineering or disassembly is prohibited.
* Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of
Dolby Laboratories. Confidential unpublished works. © 1992-1997 Dolby Laboratories, Inc. All rights reserved.
* “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
* Certain audio features of this product manufactured under license from Desper Products,Inc. Spatializer and
the circle - in - square device are trademarks owned by Desper Products,Inc.
* Unauthorized recording of copyrighted television programs, films, video cassettes and other materials may
infringe the rights of copyright owners and be contrary to copyright laws.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Before using your unit
Disc playback operation
Safety Precautions ...........................................2
Features ...........................................................4
Contents...........................................................5
Parts and functions ..........................................6
Display .............................................................7
Remote control.................................................8
Connections and Installation ..........................10
Playback connection ......................................11
DISC...............................................................40
Setting setup language ..................................41
Playback procedure........................................42
Special playback ............................................43
DVD Picture Signal Selection/Zooming ..........44
Repeat playback.............................................45
Memory playback/Random playback ............. 46
MP3 Playback ................................................47
Changing soundtrack language /
Setting up the VCR section
Setting the TV to the AV-Channel...................13
Setting the On-screen language ....................14
ATS Automatic Tuning System and
Auto Time /Date Setting .................................15
ATS.................................................................16
Setting the Time and Date..............................19
Manual TV station presetting..........................20
Changing Subtitles language .........................48
Changing angles / Title selection /
DVD menu ......................................................49
Advanced function of DVD section
Parental control ..............................................50
Setting menu language ..................................52
Setting audio soundtrack language ................53
Setting subtitle language................................54
Setting the aspect ratio of TV screen /
Tape playback operation
Loading and Unloading a Cassette Tape .......22
Cassette tape playback ..................................23
Special playback/Playback sharpness ...........24
Repeat Playback ............................................25
Counter Display..............................................26
Video Index Search System ...........................27
Setting on Screen display ..............................55
Setting Audio ..................................................56
Setting Operation ...........................................57
Selecting the sound enhancement (E.A.M.)/
Setting Background/Setting Screen Saver .....58
Setting initial setup/output sound
conversion table .............................................59
Status display of Disc .....................................60
Table of languages .........................................61
Recording
Recording a TV Program................................28
Instant Timer Recording (ITR) ........................30
ShowView®-Recording ...................................31
Timer-Recording ............................................33
Additional information
Problems and troubleshooting ....................... 62
Video head cleaning....................................... 63
Specifications ................................................. 64
Advanced function of VCR section
Detailed Description of the VPS/
PDC Function.................................................35
NICAM/German A2 Stereo Recording
and Playback..................................................36
Audio Mixing...................................................38
Duplicating a Video Tape ................................39
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and functions
Front
VCR/DVD mode selector button
Cassette Loading Slot
PLAY button
OPEN/CLOSE button
EJECT button
STOP button
Disc tray
Display window
Remote sensor
POWER
button
DVD indicator
REC button
PR +/– buttons
REW (Rewind) button
AUDIO (L/R)/
VIDEO IN jacks
VCR indicator
FF (Fast Forward) button
Rear
AC power cord
SCART PRISE PERITEL
RF IN jack
RF OUT jack
DVD OPTICAL
DIGITAL AUDIO
OUT jack
DVD COAXIAL DIGITAL
AUDIO OUT jack
SCART-socket
(for VCR/DECODER)
DVD AUDIO (L/R) OUT jacks
DVD S-VIDEO OUT jack
SCART-socket
(for TV-RGB/Composite)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Display
Display window
1
2
3
4
10
5
9
8
7
6
No. Display
Description
1
2
3
4
5
VCR
VCR mode
Playback (lights) / Auto resume (flashes)
Still picture
DVD disc is inserted.
DVD
CD is inserted.
CD
Clock display (colon[ : ] flashes)
10 : 00
01 : 00
2
Counter display by hour/minute at VCR/DVD / by minute/second at CD
Track number display for CD
TV channel position display
6
CH 2
A1/A2/A3
External input display
7
8
Timer recording display
Video tape is in the unit
Track display for CD
9
TRK
REC
Normal recording display (flashes during Instant Timer Recording - ITR
)
10
Note:
Some discs may be displayed wrong or e.g. chapter number, playback time, etc. may not be displayed.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
Page
14,41
14
TV/VCR/DVD switch Switch to operate TV or VCR or DVD
Power on/off
Turn the connected TV on or off
8
DVD MENU
MEMORY
RETURN
OPEN/CLOSE
DISPLAY
A.TRK
SUB TITLE
C. RESET
ANGLE
Display menu of DVD software
Index for DVD
Remove DVD set up menu
Open or Close the tray
Change the front Display mode
Digital AUTO TRACKING
Set Subtitle of a DVD disc
Reset the counter to 00:00
Change playback angle of a DVD disc
49
46
50
42
26
24
48
26
49
ZERO RETURN Stop the tape when the counter reaches 00:00 26
(SP/LP)
PLAY MODE
ZOOM
Sets the tape speed for recording
Select playback mode
Zoom (for DVD playback)
Select title of a DVD disc
28,30,39
45,46
44
TITLE
49
REPEAT A-B
0-9
Repeat playback between A and B (DVD/CD) 45
Direct channel selection of TV
Input setting
28,30
15~18,31,33,46,47
Enter a password
Scart input or AV-Front input
SHOWVIEW-Recording
50
34,39
31
AUX
PROG.
Confirmation of Timer-Recording
Set the unit to start recording at a preset time. 32,34
34
•
TV ∏ (INPUT) Switch the connected TV to external mode
8
29
10
TV/VCR
TV @ +/–
8
Switches between TV and VCR
Adjust the connected TV’s volume
Rewind/Review playback
Playback
23,24,43
23,42,47
1
9
Fast Forward/Forward search playback 23,24,43
2
Recording
Stop
28,30,39
23,42,47
3
4
Still picture/Recording pause on/off 24,28,39,43
SKIP 6/7
INDEX 6/7 Search for the INDEX mark of a tape
Skip chapter to forward or reverse direction
43
27
JVC TV Remote Control
TV/VCR PR +/– Select channel of the connected TV or VCR
This Remote can control some functions
8,28,30,39
(
, NUMBER (0-9), TV ∏, TV @ +/–,
C/D
SET –/+
Cursor buttons
Setting buttons
TV PR +/– and OK) of a remote controllable
JVC TV by slide TV/VCR/DVD switch to TV.
32~34
Manual tracking buttons in playback mode
Cursor buttons - To move Up in the VCR menu
you press the A. To move Down in the VCR
menu you press the B.
24
B/A
NOTE:
• It’s not possible to operate a unit not
equipped with a remote sensor.
• This Remote can control a JVC TV only.
• When you operate the VCR or DVD, the
TV/VCR/DVD switch must be slided to
VCR/DVD again. Otherwise the DVD/
VCR may not operate properly.
• Since this unit is combined type of DVD
and VCR, the remote code of DVD is
individual. So please note that the DVD-
keys on the RCU of the other JVC
RECEIVER/TV is not effective for this unit.
OK
Enter information in the menu/Select option in the menu
SET UP MENU Display menu of setup
CANCEL
14~21,41,50~59
34
Delete Timer program
Cancel input data in the setting mode 18,21,46~50
Display VCR or DVD operation status 28~30,60
OSD
A.MONITOR
Switches sound
Change sound track language of DVD
Slowmotion playback
37,38
48
24,43
24
SLOW
SKIP SEARCH
Skip the unwanted short material of a tape
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
How to install the batteries
Use micro batteries type R6.
Open the battery compart-
ment cover in the direction of
the arrow.
Install two "AA" batteries (not
supplied), paying attention to the
polarity diagram in the battery
compartment.
Replace the compartment
cover.
1
2
3
Battery precautions
The precautions below should be followed when using batteries in this device:
1.Use only the size and type of batteries specified.
2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.
3.Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.
4.If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
Distance of Remote
Control Operation
Effective angle:
approx. 60°
approx.
5m
Point the remote
control directly at the
remote sensor.
Change the custom code for remote control
If you operate this DVD/VCR with another JVC’s VCR simultaneously arranging them side by side, the both
recorders will react to this remote control. In this case, you can change the remote control and DVD/VCR to
other frequency (“ ”). Then you can operate only this DVD/VCR with this changed remote control.
When you purchased, the DVD/VCR and remote control have been set to the frequency-“ ”.
Example: Change frequency to
Remote control:
DVD/VCR:
While holding VCR, press 2 (code: b) of Number keys.
(in case of code: A, press 1). Then press OK.
In the POWER off mode, press and hold PLAY for
more than 5 seconds. The current code (“A” or “b”) will
appear on the display. Then press 3 on the remote
control. The current code of the remote control will be
transmitted to the unit and the unit will be adjusted to
the transmitted code. Then the code will disappear
after approx. 4 seconds.
NOTE:
• If the remote control has been set to b, the DVD/VCR also must be set to b. Otherwise, the DVD/VCR can not
be operated with this remote control.
• To reset to “A”, repeat above procedure. However press 1 instead of 2.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Installation
Connect your DVD/VCR to your home's antenna and to your TV-set as shown in the illustration.
When you have finished these connections you connect your DVD/VCR to the 230 V / 50 Hz mains.
Antenna
TV
TV Scart Socket (A1)
Antenna-Input
VCR/DECODER
Scart Socket (A2)
RF-Input (from
house antenna)
To Scart socket
DVD/VCR
RF-Output (to TV)
AC power cord 230V/50 Hz
Scart cable (not supplied)
Supplied Coaxial cable
Connect a TV with the Scart socket
In addition to the coaxial cable connection, connect also with scart cable. The picture and sound will be transmitted
best through the scart cable. In this case, the TV need not be tuned to the video recorder. The AV-channel also need
not be tuned. The video recorder switch the television to video operation through the scart cable automatically. The
stereo-playback is possible in only case through a scart cable!
If your TV-set does not switch to video-playback operation automatically, please
turn your TV's video switch to VIDEO position manually.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback connection
The exact arrangement you use to interconnect various video and audio components to the DVD/VCR is
dependent on the model and features of each component. Check the Owner's Manual provided with each
component for the location of SCART socket.
Connection to a Satellite Receiver
If a Satellite Receiver is used, we recommend the following configuration:
SCART-cable (not supplied)
Satellite
TV
Antenna
DVD/VCR
Satellite
Receiver
SCART-cable (not supplied)
To record from Satellite Receiver press "AUX" on the remote control of DVD/VCR twice. "A2" will appear
on the front display. Select the desired TV-program at Satellite Receiver.
Connect to a TV with S-Video Output
TV
S-Video Cord (not supplied)
DVD/VCR
Audio (L) Output
Audio (R) Output
To S-Video Input
S-Video Output
To Audio (R) Input
To Audio (L) Input
AUDIO Cord (not supplied)
Note:
• The S-VIDEO jack is useful only for DVD section.
• If you use the connection with S-Video Cord, set the "Video Out Select" (P.44) to "Video".
Connection to a Decoder (for Premiere Programs)
SCART-cable (not supplied)
TV-unit
DVD/VCR
Cable TV-
connection
Decoder
RF-Output
SCART-cable (not supplied)
SYSTEM SETUP
CLOCK SET
LANGUAGE/SPRACHE/LANGUE
AV2
[DEC]
SELECT :
ENTER
EXIT
:
:
OK
MENU
Note: Make sure that AV - mode in SYSTEM SETUP - menu has been set
to DEC .
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback connection
Connect to a Stereo Amplifier with Audio Output
If your DVD/VCR is connected to a stereo amplifier, the video soundtrack can output through the loudspeakers of
the stereo system.
SCART-cable (not supplied)
To SCART
input
SCART-Socket
(for TV-RGB/Composite)
DVD/VCR
Stereo Amplifier
Audio (L) Output
Audio (R) Output
TV
To Audio (L) Input
To Audio (R) Input
AUDIO Cord (not supplied)
Connect to an AV Amplifier with built-in digital surround
If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems
such as Dolby Digital and DTS by using the Coaxial Digital Output.
Use this connection to connect an:
• AV amplifier with built-in *Dolby Digital decoder
• AV amplifier with built-in *DTS decoder
SCART-cable (not supplied)
To SCART
DVD/VCR
SCART-Socket
input
(for TV-RGB/Composite)
TV
AV Amplifier with
Coaxial digital
Audio Output
built-in various
Coaxial digital cable
(not supplied)
decoder as above
Connecting the optical digital cable
You may connect to an AV Amplifier with an Optical digital cable (not supplied) instead of a Coaxial digital
cable.
When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel.
When not using the optical digital cable, attach the dust protection cap to protect against dust.
NOTES:
• The OPTICAL, COAXIAL jacks are useful only for DVD section.
VHS signal is output only from the SCART-sockets, AUDIO L/R jacks and RF OUT jack.
• When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on the AV
Amplifier. If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the
speakers to be damaged.
• DTS audio will be output only from the COAXIAL output. To hear DTS audio, DTS-Decoder is necessary.
When playing DTS-encoded CDs, only noise will be heard from the speakers or analogue stereo outputs.
• Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the TV to the AV-Channel
We recommend that television and DVD/VCR are being connected with a scart cable.
In this case, the setting of AV-channel is not necessary. Picture and sound of video cassette will be transmit-
ted to television through the scart cable automatically. Please read the next page.
In case of no scart cable connection,
you must set the television to the AV-
channel. Pay attention to the following
notice:
Preparation
•
•
Turn on the TV.
Make sure the power of DVD/VCR has been turned off.
A built-inTV-broadcast in DVD/VCR can
do the video playback through the sup-
plied antenna cable.This broadcast is
sent on UHF, channel 36.To receive this
broadcast, you must tune your televi-
sion to channel 36 in UHF-band.(see
step 2)
Press the DVD/VCR’s
control) and keep pressing it until the display shows rF:.
The number next to rF: is the channel in UHF-band to
(not the one on your remote
1
which you must tune your TV-set.
VCR
Switch your television to the program position on which
the video playback is seen. Start the channel search of
your television until “TEST” appears. Store this tuning in
television like also the case of the reception for normal
television-channels you would store.
2
In case a broadcast has already sent
to channel 36 in your area or you con-
nect a additional equipment (e.g. Sat-
ellite receiver) with a coaxial cable
(without a scart cable), you must tune
the sending channel in DVD/VCR (see
step 3). In your television store the both
equipment (the DVD/VCR and the sat-
ellite receiver) to 2 different program
positions.
TEST
IfyouwanttouseyourDVD/VCR,switch
your television to this program position.
If there is interference in the picture (you see 2 programs
simultaneously or what is called Ghosts), change the
sending channel in DVD/VCR. To do this, go back to the
step 1. Use PR button on the DVD/VCR to change the
number next to the rF:. Then return to step 2 and tune the
television newly.
Example:Your satellite receiver is sent
to channel 36. You tune the DVD/VCR
to channel 40 (see step 3).
3
4
(If your DVD/VCR is also sent to chan-
nel 36, the interference will occur.)
In your television store the channel 36
to e.g. program position 3 and store the
channel 40 to e.g. program position 4.
Note that the program position 4 must
be suitable for video-playback espe-
cially. Please see the owner's manual
for your television. If the playback pic-
ture is often distored, you must select
the other program position for DVD/
VCR.
Press
button to turn off the DVD/VCR.
1,4
TEST
3
Note:
If you receive one TV-program on channel 35, 36 or 37, the interference can be occurred to the built-in TV
channel in DVD/VCR. If you use a scart cable for the transmission of picture and sound, you can cut off the
built-in TV-program. Then the video playback through the supplied antenna cable is not possible any more.
Press PR repeatedly (at step 1) until OFF will appear.(OFF appears after 69 or before 23)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the On-screen language
Turn on your TV and select the AV-
Program position, on which you have
already set your DVD/VCR. (it will
happen automatically by Scart-cable
connection). So you can follow up the
all setting on TV screen.
Preparation:
• Press the
button to turn on the DVD/VCR.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press VCR to select the VCR mode. (The VCR indicator will light)
You can choose from three different languages (English,
French and German) for the on-screen displays.
Press SET UP MENU.
ATS (AUTO TUNING SYSTEM)
1
Press
or
to select the
TIMER REC SET
VCR EXTENSION
VCR SETUP
CHANNEL SETUP
SYSTEM SETUP
SYSTEM SETUP option, then
press OK.
If you use the unit for the first time
and press SET UP MENU,
instead of the main menu screen
on the right the “LANGUAGE”set
up menu screen in step 2 may
appear.
SELECT
:
ENTER : OK
EXIT
: MENU
Press
or
to select the
SYSTEM SETUP
2
3
“LANGUAGE” option, then
press OK.
CLOCK SET
LANGUAGE/SPRACHE/LANGUE
AV2
[DEC]
SELECT
:
ENTER : OK
EXIT
: MENU
Press
or
to select the de-
LANGUAGE/SPRACHE/LANGUE
sired language: English (EN-
GLISH), German(DEUTSCH)or
French (FRANCAIS), then press
OK.
ENGLISH
DEUTSCH
FRANCAIS
SELECT :
OK: OK
Press SET UP MENU repeatedly until the TV picture appears
on the screen.
4
NOTES:
• If the unit does not operate prop-
erly, or No key operation (by the unit
and/or the remote control): Static
electricity, etc., may affect the player's
operation. Disconnect the AC power
cord once, then connect it again.
• Both the VCR and the DVD have their
own menu option (See page 41).
• If no buttons are pressed for more than
60 seconds, the MENU screen will
return to normal TV-operation auto-
matically.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ATS Automatic Tuning System and Auto Time/Date Setting
This VCR has a built-in TV receiver
module. Before you can record a TV
program, all the available TV stations
must be tuned in and preset in the
memory. The ATS function (Automatic
Tuning System) allows all the locally
available TV stations to be automati-
cally stored and sorted according to
the currently effective national station
list. To accomplish this, ATS will need
about 12 minutes. During this period
of time the VCR cannot be used. If you
wish to change the station sequence,
you can later perform a removing
procedure (see page 17).
Preparation:
• Press the
button to turn on the DVD/VCR.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press VCR to select the VCR mode. (The VCR indicator will light)
Press SET UP MENU. Press
1
ATS (AUTO TUNING SYSTEM)
or
repeatedly until the dot
TIMER REC SET
VCR EXTENSION
VCR SETUP
CHANNEL SETUP
SYSTEM SETUP
SELECT :
ENTER : OK
EXIT : MENU
before ATS (AUTO TUNING
SYSTEM) blinks.Then press OK.
If no channel setting is done:
Press 1 of number keys at first, and then press SET UP MENU.
Press
/
or
/
to select
2
ATS (AUTO TUNING SYSTEM)
AREA
the desired country. Then press
the OK.
GERMANY
HOLLAND
AUSTRIA
DENMARK
ITALY
SWISS
SELECT :
OK : OK
EXIT : MENU
The ATS setting is completed when “CHANNEL MAPPING”
indication and the current time display appears.
Press SET UP MENU repeatedly until the TV program will be
displayed.
3
CHANNEL MAPPING
1 ARD
2 ZDF
3 RTL
4 SAT1
PRO 7
BR3
SW3
N3
5
6
7
8
9
HR3
10 WDR3
MDR3
TM3
11
12
ATS ACTIVE
SELECT
SKIP
:
: CANCEL
CHANGE NAME : 1
MOVE
EXIT
: 2
: MENU
VCR
If the CLOCK SET-menu appears and 00:00 appears in the display,
please set the clock manually. In this case, no station transmitting
time data can be received (see page 19).
Note: If ATS is done under the bad receiving condition, one or more
stations may not be found. In this case, set these stations
manually.(see page 20)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ATS
Preparation:
Skipping unwanted TV stations
(Skip those TV stations that are not
wanted to be selected by pressing the
PR button.)
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press VCR to select the VCR mode. (The VCR indicator will light)
Press SET UP MENU.
1
ATS (AUTO TUNING SYSTEM)
Press
or
to select
TIMER REC SET
VCR EXTENSION
VCR SETUP
CHANNEL SETUP
SYSTEM SETUP
CHANNEL SETUP. Then press
OK.
SELECT
:
ENTER : OK
EXIT
: MENU
Press
or
to select
2
3
CHANNEL SETUP
CHANNEL MAPPING. Then
press OK.
CH TUNING
CHANNEL MAPPING
SELECT :
ENTER : OK
EXIT
: MENU
Press
/
or
/
repeatedly
CHANNEL MAPPING
until the TV station to be skipped
blinks.
1 ARD
2 ZDF
3 RTL
4 SAT1
5 PRO 7
6 BR3
7 SW3
8 N3
9 HR3
10 WDR3
11 MDR3
12 TM3
SELECT
SKIP
:
: CANCEL
CHANGE NAME : 1
MOVE
EXIT
: 2
: MENU
Then press CANCEL.
The number before the canceled
channel (e.g. 12) will be
bracketed.
4
CHANNEL MAPPING
1 ARD
2 ZDF
3 RTL
4 SAT1
5 PRO 7
6 BR3
7 SW3
8 N3
9 HR3
10 WDR3
11 MDR3
12 TM3
SELECT
SKIP
:
: CANCEL
CHANGE NAME : 1
MOVE
EXIT
: 2
: MENU
Canceling the skip function:
Press or repeatedly until the skipped TV station blinks,
then press CANCEL.
/
/
The brackets will disappear.
Press SET UP MENU repeatedly until the TV picture appears
on the screen.
5
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ATS
Reassigning TV station positions
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The
VCR indicator will light)
Example: Reassign the TV station under No. 6 to position No. 2.
Select the "CHANNEL MAPPING" in Menu-screen
in the same way as the step 1~2 on page 16. Then
press OK.
After
approx. 12
1
2
5
MOVE CHANNEL
1 ARD
6 ZDF
9 HR3
10 WDR3
11 MDR3
12 TM3
seconds the station
BR3 is set in new
position 2.The ZDF will
be extracted to the first
line.
5 PRO 7
6
2 ZDF
3 RTL
4 SAT1
7 SW3
8 N3
Press
/
or
/
CHANNEL MAPPING
POSITTION
MOVE
EXIT
:
repeatedly until the TV
station to be reassigned
blinks.
1 ARD
2 ZDF
3 RTL
4 SAT1
: OK
5 PRO 7
6 BR3
7 SW3
8 N3
9 HR3
: MENU
10 WDR3
11 MDR3
12 TM3
Now to finish this pro-
cedure and at the same
time set the protruded
station (ZDF) to the
blank position 6, press
SELECT
SKIP
:
MOVE CHANNEL
: CANCEL
1 ARD
2 BR3
3 RTL
4 SAT1
5 PRO 7
6 ZDF
7 SW3
8 N3
9 HR3
CHANGE NAME : 1
10 WDR3
11 MDR3
12 TM3
MOVE
EXIT
: 2
: MENU
Press "2" of number
keys. Then, the TV
station will be moved to
the first display line.
POSITTION
MOVE
EXIT
:
3
4
SET
UP
MENU
MOVE CHANNEL
6 BR3
9 HR3
10 WDR3
11 MDR3
12 TM3
: OK
1 ARD
2 ZDF
3 RTL
4 SAT1
5 PRO 7
repeatedly until TV-
station appears.
: MENU
6
7 SW3
8 N3
Or you can of course select another station to set in
the protruded station(ZDF) in step 4.
POSITTION
MOVE
EXIT
:
: OK
: MENU
Press SET UP MENU repeatedly until theTV picture
appears on the screen.
6
Press
/
or
/
repeatedly until the position
number blinks to which the selected TV station is to
be moved, then press OK.
MOVE CHANNEL
6 BR3
9 HR3
10 WDR3
11 MDR3
12 TM3
1 ARD
2 ZDF
3 RTL
4 SAT1
5 PRO 7
6
7 SW3
8 N3
POSITTION
MOVE
EXIT
:
: OK
: MENU
WAIT blinks.
MOVE CHANNEL
WAIT
1
2
3
4
ARD
ZDF
RTL
PRO 7
5
6
7
8
9
HR3
10 WDR3
The data will be
ordered in the table
newly.
MDR3
TM3
SW3
N3
11
12
SAT1
• A position number(6) will indicated near the protruded
station(ZDF) at the first line.
If any button is not pressed for more than 60 seconds,
this station(ZDF) will be set to this position number(6)
automatically.
POSITION :
MOVE
EXIT
: OK
: MENU
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ATS
Preparation:
Changing TV station names
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press VCR to select the VCR mode. (The VCR indicator will light)
For a number ofTV stations (such as
MTV) no name code will be displayed
because these TV stations do not
provide the necessary information.
You can enter the respective names
yourself. Moreover, unwanted station
codes can be changed by the user.
Example: MTV is assigned to station No.10, but the code “MTV” will
not be displayed and will also not appear in the table.
Select the "CHANNEL MAPPING" in Menu-screen in the same
way as the step 1 ~ 2 on page 16. Then press OK.
1
Press
/
or
/
repeatedly
2
CHANNEL MAPPING
until the station number position
now to be named will blink.
1
2
3
4
ARD
ZDF
RTL
5
6
7
8
PRO 7
BR3
SW3
N3
9
10
11
12
HR3
SAT1
• If you want to turn over the page
when the blinking spot is in the
left or right edge of on-screen,
SELECT
SKIP
:
: CANCEL
CHANGE NAME : 1
MOVE
EXIT
: 2
: MENU
press
or
repeatedly until
the next page's 12 stations ap-
pears.
Press "1" of number keys. The
first display line will change to
3
4
CHANGE BROADCAST NAME
1 ARD
2 ZDF
3 RTL
4 SAT1
5 PRO 7
6 BR3
7 SW3
8 N3
9 HR3
10
"CHANGE
NAME".
BROADCAST
11
12
SELECT
NAME
OK
CLEAR
EXIT
:
:
: OK
: CANCEL
: MENU
Press
or
repeatedly until
CHANGE BROADCAST NAME
the desired character appears.
Then press . Use or to
select the next character. Then
press . Up to four characters
can be used to create a station
name. The character “ ” stands
for a space.
1 ARD
2 ZDF
3 RTL
4 SAT1
5 PRO 7
6 BR3
7 SW3
8 N3
9 HR3
10 M
11
12
SELECT
NAME
OK
CLEAR
EXIT
:
:
: OK
: CANCEL
: MENU
Then press OK.
Each press of
will change the screen display as follows.
A, B, C, ... X, Y, Z
0, 1, 2, ... 7, 8, 9
–
+
/
•
Press SET UP MENU repeatedly until the TV picture appears
on the screen.
5
Note:
When a wrong character is entered,
press CANCEL and enter the correct
character.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Time and Date
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press VCR to select the VCR mode. (The VCR indicator will light)
If the time and date is not be displayed
for some reasons after the ATS
function has been completed, a manual
clock adjustment will be required.
Example: Setting the clock to 11:30, 23rd October 2002.
Press SET UP MENU. Press
1
SYSTEM SETUP
or
repeatedly until the dot
before SYSTEM SETUP blinks.
Then press OK. Then press
CLOCK SET
LANGUAGE/SPRACHE/LANGUE
AV2
[DEC]
or
repeatedly until the dot
before CLOCK SET blinks.Then
press OK.
SELECT
:
ENTER : OK
EXIT
: MENU
Press
/
repeatedly or
number keys until “23” appears.
Then press
2
3
4
CLOCK SET
DAY
23 WED
1
MONTH
YEAR
TIME
.
2002
0:00
AUTO TIME ON
SELECT
SET
OK
:
:
/ 0–9
: OK
EXIT : MENU
Set the month, year, hour and
minute in the same way as the
step 2. Then press
CLOCK SET
DAY
23 WED
MONTH
YEAR
TIME
10
2002
11:30
.
AUTO TIME ON
Note:
SELECT
SET
OK
:
• In case of a power failure the clock will
continue to operate for another 30 min-
utes with quartz-controlled precision.To
indicate that the power failure has lasted
for an excessive period of time “0:00”will
blink on the display. In this case read-
just time and date.
:
/ 0–9
: OK
EXIT : MENU
Press
or
to select “ON” or “OFF”, then press OK. If “ON” is
selected, any required time corrections will be performed
automatically (see left). In this case the personnel of the
appropriate TV station or of Telecom will be responsible for
If the clock does not have been adjusted
yet, the step 1 will appear automatically.
• The clock will only be automatically set
when the VCR is connected to the
Telecom CATV network.All the provided
CATV stations should be stored in the
VCR. This is the case when the ATS
function has been completed. The an-
tenna system must be free of any de-
fects, e.g. there should be no picture
noise.The clock will be re-adjusted every
30 minutes except the period between
23:00 and 1:00 o’clock. In case the total
difference between the indicated time
and the current time is more than 5 min-
utes, the clock will not be corrected.The
switching from winter time to summer
time will be considered.
correcting the time setting. If any
CLOCK SET
error occurs during such an
adjustment (e.g. switching from
summer time to winter time), your
clock will show the incorrect time.
To set the correct time select
“OFF” and follow the procedure
described above.
DAY
23 WED
10
MONTH
YEAR
TIME
2002
11:30
AUTO TIME ON
SELECT
SET
OK
:
:
: OK
EXIT : MENU
• In case of an erroneous input press
step and enter again.
to go back to before
Press SET UP MENU repeatedly until the TV picture appears
on the screen.
5
6
The clock will begin operation and the colon will blink on the
VCR display.
The clock will not be adjust automati-
cally when:
• timer activated.
VCR
• antenna not connected.
• only an outdoor antenna or a satellite
receiver connected.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual TV station presetting
ATS stores the broadcast automatically.
However if you do the ATS under
unfavorable receiving conditions,
some broadcasts happen to be not
finded by ATS. For these broadcasts,
you can store also by manual.
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press VCR to select the VCR mode. (The VCR indicator will light)
Example: Preset the SAT1 on program position 5.
Press SET UP MENU.
1
ATS (AUTO TUNING SYSTEM)
Press
or
to select
TIMER REC SET
VCR EXTENSION
VCR SETUP
CHANNEL SETUP
SYSTEM SETUP
CHANNEL SETUP. Then press
OK.
SELECT
:
ENTER : OK
EXIT
: MENU
Press
or
to select CH
2
3
CHANNEL SETUP
TUNING. Then press OK.
CH TUNING
CHANNEL MAPPING
SELECT :
ENTER : OK
EXIT
: MENU
DEC OFF will blink. Press OK.
DEC OFF does not blink any
more. SEARCH will appear.
VPS CH
1
ARD
Note:
DEC OFF
If you wish to store the
PREMIERE manually, the
decoder must have been
connected as on the lower of p.11.
SELECT :
EXIT :
MENU
OK
: OK
During DEC OFF is blinking, press
DEC ON will blink now.
Press OK.
.
Press
(rising frequency) or
4
CH 1
(falling frequency) once. The
search starts. It stops at each
broadcast automatically ("
change to " 4 "). Press or
repeatedly until the SAT1
appears.Only in case of receiving
of the weak broadcast (drifting
picture), search dose not stop. If
"
DEC OFF
SEARCH :
/ F. TUNE :
EXIT
: MENU
Note:
you want to stop, press
/
or
Occasionally, the auto search might catch
a weak signal and stop. If the TV station
signal is weak, you shouldn't store this
station.
/
.
In that case restart the auto search using
or
.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual TV station presetting
The Fine Tuning adjustment
Please wait until OK: ENTER
appears. It may take a few
seconds.
5
6
Under a normal receiving condition, the
station-search will stops automatically at the
best receiving position. That picture will
appear without disturbance.
This receiving position will be memorized
automatically. The Fine Tuning can not be
memorized additionally.
VPS CH
1
SAT1
Then press OK.
In the next step, the program
position on which this station
should be stored will be set.
DEC OFF
SELECT :
/ F. TUNE :
EXIT :
: OK
OK
MENU
In rare case of bad receiving condition, the
station-search might not stop at the best
receiving position. That picture will appear
with disturbance, e.g. waving lines.
Only in this rare case, use the Fine Tuning to
tune the concerned station manually and
exactly.
Press
or
repeatedly until
VPS CH
5
"5" displayed.
Or enter 5 with number keys.
Then press OK.
SAT1
DEC OFF
In step 5, press
adjusted to best position. Then press OK.
or
until the station is
CH
OK
:
/ 0–9
EXIT :
MENU
: OK
Repeat the steps 3 and 6 to preset other TV stations.
7
8
Press SET UP MENU repeatedly until the TV picture appears
on the screen.
To skip a channel position
Unwanted channels can be skipped so that they cannot be called
up by pressing PR. Select the channel to be skipped...
CH 29
SWF
VPS
VCR
....e.g. channel 29.
Select channel 29, then press CANCEL.
This channel’s number will be flashing. That way you can cancel
further channels one after the other.
To cancel the channel skipping
Note:
Select the skipped channel using number keys, then press
Even the skipped program position can be CANCEL. The channel No. does not blink any longer, and the
called up with number keys.
channel No. now may be selected again using PR.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading and Unloading a Cassette Tape
Use only video cassette tapes marked
and
.
• Cassettes marked “VHS” (or “S-VHS”) can be used with this video cassette recorder. However, S-VHS recording
is not possible with this model.
• This model is equipped with SQPB (S-VHS QUASI PLAYBACK) that makes it possible to play back S-VHS
recordings with regular VHS resolution.
• HQ VHS is compatible with existing VHS equipment.
• SQPB playback can be seen only at PAL SP mode.
Insert the cassette tape with its labeled side facing up
and the erase prevention tab positioned at your left.
An inverted cassette tape cannot be inserted.
Loading
Push the center of the tape until it is automatically
inserted.
VCR
Erase prevention tab
Automatic power ON
When you insert a cassette tape the DVD/VCR power will turn ON automatically.
Automatic playback
When loading a cassette tape without an erase prevention tab, playback will start automatically.
Unloading
Press EJECTon the unit. Even if a tape is being
played, press this button only once.
Remove the cassette tape.
1
2
VCR
VCR
Automatic tape eject
This VCR will automatically rewind the tape when the tape has ended. And when the tape is rewinded to its
beginning, the cassette tape will be ejected automatically.
To prevent accidental erasure
To record again
Removetheerasepreventiontabwithascrewdriver.
Cover the hole with a piece of adhesive tape.
Screwdriver
Erase prevention tab
Adhesive tape
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Cassette tape playback
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press VCR to select the VCR mode. (The VCR indicator will light)
Load a prerecorded tape
1
(When loading a cassette tape
without the erase prevention
tab, playback will start auto-
matically).
To start playback
2
Press
.
Playback will start.
If the cassette has not loaded
yet,
will blink for 4 seconds.
VCR
To stop playback
Press 3.
VCR
To rewind the tape or forward it rapidly
Stop the playback or recording with 3.
To rewind the tape:
Press
To forward the tape:
Press
.
.
To stop the tape-winding, press 3. To switch to playback directly
(without 3), press
.
Forward/Reverse picture search mode
When the tape is being winded, you can switch to picture search
mode(seenextpage).Todothis,press or andholditdown.
The unit will resume the tape winding as soon as the button is
released.
NOTES:
• This VCR selects the playback tape
speed SP or LP automatically.
• The Cassette tape and DVD disc can
be played back simultaneously. If you
press VCR or DVD, the tape playback
and DVD playback alternate with each
other on the screen.
NTSC video cassette playback
When using a pre-recorded NTSC video cassette tape, the
connected TV set must operate with a 60 Hz vertical frequency.
Otherwise the on-screen picture will be affected by vertical
rolling.EvenifyourVCRsetiscapableofprocessingNTSCvideo
signals, the picture may be shortened vertically (appearance of
black bars at the top and at the bottom of the TV screen). The
dubbing of a NTSC video cassette tape to a standard PAL VCR
is not possible.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Special playback/Playback sharpness/Skip Search
Special playback
Playback sharpness
Adjust the sharpness of playback picture during playback.
During slow motion, still picture and picture search,
sharpness-adjusting is impossible.
Picture Search
Reverse picture search function
Press
x 1 or x 2 during the playback.
Start the playback of video tape.
Forward picture search function
Press x 1 or x 2 during the playback.
1
To return to playback: Press
.
Press SET UP MENU.
2
ATS (AUTO TUNING SYSTEM)
Press
or
to select
TIMER REC SET
VCR EXTENSION
VCR SETUP
CHANNEL SETUP
SYSTEM SETUP
VCR SETUP.Then press
Still Picture
Press 4 during playback. To resume normal
OK.
playback: Press
.
SELECT
:
VCR
ENTER : OK
EXIT
:
MENU
Slow Motion
During playback press SLOW.
You can change the slow speed by the additional
pressing of SLOW.
To return to playback: Press
Press
SHARPNESS. Then
press OK.
or
to select
3
4
VCR SETUP
VCR
NICAM
AUDIO MIX
SHARPNESS
[AUTO]
[OFF]
.
Slow tracking and vertical lock adjustment
SELECT :
If noise bars appear in the picture during slow motion,
press the SET + or – to reduce the noise bars.
If the still picture jitters excessively, press SET + or –
to stabilize the still picture.
ENTER : OK
MENU
EXIT
:
"SHARPNESS" will appear
and then disappear after
60 seconds of the last
button-press. Adjust with
Frame by Frame picture
During playback, press 4 one by one: The picture
advances frame by frame.
To return to playback: Press
VCR
sharper or
lesser.
.
Adjusting tracking condition
Automatic tracking adjustment
softer
sharper
Whenever you insert a tape and start playback,
automatic tracking starts working and continuously
analyzes the signal to enable optimum picture quality
during playback.
Press SET UP MENU repeatedly until the TV picture
appears on the screen.
5
Note:
Manual tracking adjustment
To return to the initial sharpness setting, press CANCEL
while the sharpness setting screen is appearing.
If automatic tracking cannot eliminate noises well during
playback, press SET + or SET – to eliminate the noises.
“MANUAL TR.” will appear. Press it briefly for a fine
adjustment, or press and hold for a coarse adjustment.
Skip Search
Each time you press SKIP SEARCH while a tape is playing,
the unit will fast-forward ahead approx. 30 seconds on the
tape. You may press the button up to six times in a row to
move approx. 180 seconds (three minutes) ahead.
To return to automatic tracking, press A. TRK.
Notes:
•
The audio output is muted during SPEED SEARCH,
STILL, FRAME ADVANCE and SLOW MOTION.
For example: 1 press: approx. 30 seconds of tape
2 presses: approx. 60 seconds of tape
• During picture search mode there will be noise bars
which are caused by the system.
3 presses: approx. 90 seconds of tape
• The Special Playback will automatically change to
playback after approx.5 minutes to protect the video
tape against excessive wear.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat Playback
Normal repeat playback
The entire video tape will be played until its end. The tape will
then automatically rewind to the beginning and the playback will
be repeated.
Press SET UP MENU. Press
or
to select VCR
1 EXTENSION. Then press OK.
Press
or
to select AUTO REPEAT.
2
3
Then press OK to select [ON] or
[OFF].
If [ON] is selected, the playback
will be repeated endlessly.
VCR EXTENSION
AUTO REPEAT
SCENE REPEAT
[ON]
SELECT :
/
ENTER : OK
MENU
EXIT
:
Press SET UP MENU until the menu screen is cleared.
4
5
To start the playback, press
.
The playback will be repeated endlessly.
To cancel normal repeat mode:
Follow the above step 3, then press OK to select the OFF
position. Press SET UP MENU to return to the TV.
Scene repeat playback
Press SET UP MENU.
1
Press
or
to select VCR EXTENSION. Then press OK.
Press
or
to select SCENE
2
VCR EXTENSION
REPEAT. Then press OK.
AUTO REPEAT
SCENE REPEAT
[OFF]
Theplaybackstartsautomatically.
SELECT :
ENTER : OK
MENU
EXIT
:
Press OK at the point you want to
start scene repeat play-back.
3
S – REPEAT
S–REPEAT will blink on the
screen.
Press OK once again at the point
4 you want to end scene repeat
SR – R
playback.
NOTE:
If the unit is turned off or starts record-
ing, the repeat mode is canceled.
SR–R will appear on the screen
and the tape will be rewinded
automatically to go back to the
starting point.
When the starting point was
5
SR – PLAY
found, the Scene repeat-play-
back will start automatically.
SR-PLAY will appear only once.
To stop Scene repeat playback:
Press 3.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Counter Display
Preparation:
ZERO RETURN function
This function makes tape-rewinding
stop at the counter 00:00:00 position
automatically.
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press VCR to select the VCR mode. (The VCR indicator will light)
Press OSD.
1
The counter display shows the
tape running time during
playback or recording.
The Recorder will indicate REC
during recording for itself.
VCR
12:00 SUN
STEREO
CH
2
ZDF
00:04:38 SP
Press C.RESET at the desired
tape position.
The counter display will be reset
to the "00:00:00" position (e.g.
the beginning of recording).
2
12:00 SUN
STEREO
CH
2
ZDF
VCR
00:00:00 SP
Press 3 when playback or recording is finished.
Press ZERO RETURN.
The tape will be rewinded or fast forwarded and automatically
3
4
stop at the ”00:00:00” position.
Press OSD once again to make the all indicator disappear.
The DISPLAY-button
Press DISPLAY during the playback. The clock and tape counter
alternate with each other in the display.
VCR
Note:
You can set the tape counter to 00:00:00 with C.RESET anytime.
Therefore, the counter display can also indicate 00:00:00, even when
the tape counter does not reach its beginning yet. Even if the tape
counter indicates 00:00:00, it can be rewinded moreover. If the tape
was rewinded over the point of 00:00:00, the minus mark (–) appears
in the counter display. Although the tape counter seems to forward
Note:
• When you load a video cassette, the dis-
play indication changes to "00:00".
• The counter display does not function
on non-recorded (blank) sections of the
tape. When you rewind, fast forward or
play tapes through blank sections, the
counter display stops.
when you press
, in fact the tape is being rewinded. When the
tape reaches the beginning, the tape-rewinding stops automatically.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Index Search System
Example: Indexing of TV commercials.
Whenever a recording is begun an
invisible index mark is recorded on the
tape.These index marks are all identical,
and each mark means: "Here starts a
new recording". Every DVD/VCR
equipped with the Video Index Search
System (VISS) can locate these marks
at the beginning of any recording.
Start playback and wait until the
end of the TV commercial is
reached, then press 3.
1
While holding 2, press
indication goes off, 3 may be pressed. This short recording
process will be sufficient to set an index mark.
once. When the "INDEX" on-screen
2
This will result in about 10 seconds of the TV commercials to be
overwritten by another recording. Due to the system the end of
this recording will be followed by a recording gap (noise signal)
of approx. 5 seconds.
Recording several Index Marks
Due to the system only one index mark will be recorded at the
beginning of a recording. If you intend to set several index marks
during a single recording, follow the procedure below:
At the point of the recording where
1
an index mark is to be set press 4.
Theunitwillswitchtotherecording
pause mode.
VCR
REC
Press PR +/
back to the original TV program.
Press 4 to resume recording.
–
repeatedly to switch
2
VCR
REC
Index Search
Press INDEX + or – during stop or play
mode.
For Succeeding programs:
Press INDEX +.
For Preceding programs:
Press INDEX –.
(Additional press increases the INDEX
NO. up to 9.)
When the INDEX + or – is pressed, the
unit starts searching the INDEX NO.
selected and finds the portion, then
playback starts automatically.
To stop the Index Search, press 3.
Notes:
•
When you record an INDEX mark at
the very beginning of the tape, the
mark may not be found.
During INDEX search, the tape may
stop and begin to play at a slightly
different location.
•
7 or 6 is displayed
•
•
INDEX may not function properly with
old or worn out video tapes.
INDEX marks may not be found if it is
extremely close to the point where the
search began.
Inrecording,ifyoustoprecordingtem-
porarily, the INDEX mark is not re-
corded on the tape.
INDEX NO. (up to 9)
•
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a TV Program
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press VCR to select the VCR mode. (The VCR indicator will light)
Load a blank cassette tape with the
erase prevention tab intact. (The
DVD/VCR will automatically turn
1
on.)
VCR
Select the program(e.g.29) you want to record with PR +/– or
number keys.
2
VCR
1~9 : e.g. 5 = press “5”
10~80 : e.g. 29 = press “2” and “9”.
If a recording in Long Play mode is intended, press
SPEED) to display "LP". (see Note below)
(TAPE
3
4
On the VCR, press 2.
Or on the Remote, while holding 2,
press
.
"
" will appear on the screen for
about 4 seconds and “REC” will
appear on the display.
VCR
REC
If the erase prevention tab is removed, the tape will eject when
both the 2 and are pressed for recording. (see p.22)
To Stop Recording
Press 3.
VCR
To Stop Recording Temporarily
To stop a recording for a short
period of time press 4. Press this
button again if you want to resume
the recording.
Notes:
• Since the DVD/VCR has a built-in TV
tuner the TV set may be turned off when
recording. The TV set may only be used
to check for accurate program adjust-
ments or to monitor recordings.
• You can confirm on the TV-screen whether
youselectedSPorLP. PressOSDtoseethe
status display. (see page 29)
VCR
REC
Attention:
A safety circuit turns the pause mode off automatically after 5
minutes, and the DVD/VCR will stop the recording mode.
• If you wish to watch the DVD playback
during the normal recording on VCR,
press DVD to change to DVD mode and
perform the DVD playback (see page
42).
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a TV Program
Recording with a SCART Cable:
Press TV/VCR until "VCR" appears on the display. Select
the program on the DVD/VCR you want to record. This
programcanbewatchedonthescreenandrecordedbythe
1
2
You can record a program using the
TVreceiveroftheDVD/VCRandatthe
same time watch another program on
the TV set using its receiver. As the
DVD/VCR automatically switches the
TV set the following points should be
observed:
DVD/VCR.
VCR
“VCR” indicator goes on.
While the VCR is recording press TV/VCR until the "VCR"
indicator on the display goes off. The TV set now displays
the program of its built-in receiving module. Select the TV
channel you want to watch on the TV set. Although the TV
set now shows another program the DVD/VCR will con-
tinue recording the previously selected program.
REC
“VCR” indicator goes off.
Using TV/VCR you can switch the TV screen between the
DVD/VCRpictureandtheTVpicture. Ifthe"VCR"indicator
islitonthedisplay,youwillwatchtheDVD/VCRpicture.This
has no trouble on the recording.
3
VCR
REC
“VCR” indicator goes on.
To Display VCR operation Status
Press OSD. The clock, day of the week and more informa-
tions will be indicated.
To cancel the indicating: Press OSD until all indicator
disappear.
Day of the week
Time
Deck-status
here: Playback
Program
number or
Scart input
(AV1,AV2 or
AV3)
Indication for
Hi-Fi-playback
or stereo-
reception
23:59 MON VPS CH 80
HI-FI
****
*
Station's name
L CH
(e.g. ZDF)
01:36:58 SP
Indication for
the selected
Cassette in
Unit
playback sound
(e.g.: L CH = Left Channel)
Tape speed
Stand of Tape counter
Auto Rewind Feature
The DVD/VCR will automatically rewind
when the tape has ended (except during
ITR and TIMER REC). It will also eject
the cassette tape.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Timer Recording (ITR)
Preparation:
The instant timer recording feature
provides a simple and convenient way
to make a timed recording.
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press VCR to select the VCR mode. (The VCR indicator will light)
Load a blank cassette tape with the
erase prevention tab intact. (The
DVD/VCR will automatically turn
1
on.)
VCR
Select the program (e.g.29) you want to record with PR +/– or
number keys.
2
VCR
1~9 : e.g. 5 = press “5”
10~80 : e.g. 29 = press “2” and “9”.
If a recording in Long Play mode is intended, press
SPEED) to display "LP". (see note on page 28)
(TAPE
3
4
Press 2 on the VCR or while holding 2, press
on
the Remote to begin recording. Press 2 on the VCR again to
stop recording after 30 minutes. Each additional press of 2 will
increase recording time as shown in the chart below, up to a
maximum of 5 hours. The ITR and
recording time will appear on the
screen for about 4 seconds. And,
REC will keep blinking in the display.
ITR 0:30
CH 29
STEREO
INDEX
SWF
VCR
REC
“REC” will keep blinking
in the display.
Tape speed: SP
1:30
2:00
Recording
0:30
1:00
3:00
4:00
5:00
Tape speed: LP
Recording 0:30 1:00
2:00
3:00
1:30
4:00
.......
5:00
10:00
To Extend the Recording Time
While holding 2, press
repeatedly until the desired time
appears on the display.
.
ITR 1 : 30
CH 29
Note:
SWF
• If you wish to watch the DVD playback
during the ITR, press DVD to change to
DVD mode and perform the DVD play-
back (see page 42).
• If the tape supply has not sufficed for
ITR recording, the clock symbol ( ) will
blink at the tape-end and then VCR
mode will change to DVD mode.
In this case, press • to cancel the
blink or press EJECT to remove the cas-
sette tape.
To stop the ITR
Press 3.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
®
SHOWVIEW -Recording
Look up the SHOWVIEW number codes in
an appropriate TV program magazine.
Select the desired TV program for
recording and refer to the number code
next to it.
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press VCR to select the VCR mode. (The VCR indicator will light)
Press PROG.
SHOWVIEW NO.----------
1
ONCE
DAILY
WEEKLY
:
:
SHOWVIEW NO.
SELECT
CLEAR
0
9
: CANCEL
: OK
OK
If the clock is not set, CLOCK SET
menu will appear automatically.
EXIT
: PROG.
Enter the SHOWVIEW code with
number keys.
2
3
SHOWVIEW NO.3277--------
ONCE
DAILY
WEEKLY
:
:
SHOWVIEW NO.
SELECT
CLEAR
0
9
• In case of an erroneous input,
press CANCEL and enter the cor-
rect number again.
: CANCEL
: OK
OK
EXIT
: PROG.
Select with
or
DAILY or WEEKLY. ONCE is already set.
ONCE = To record a program only
once.
SHOWVIEW NO.327741029
ONCE
DAILY
DAILY = To record TV programs
aired daily.
WEEKLY
:
:
SHOWVIEW NO.
SELECT
CLEAR
0
9
: CANCEL
: OK
WEEKLY = To record TV programs
aired once a week.
OK
EXIT
: PROG.
Press OK. By the SHOWVIEW Code the entered data appear on
the screen.
4
SHOWVIEW NO . 327741029
DATE
START
END
15 WED
17:30
18:00
CH
— —
• If the entered Number is not cor-
rect, the indicator “SHOWVIEW
NO. ERROR” appears. Enter the
Number correctly again.
SPEED
SP
VPS/PDC OFF
SELECT :
SET
:
/ 0—9
EXIT
: MENU
• Only in case of the TV station that you decode for the first time,
the – – will blink at the CH line. That is to say, you must enter
the corresponding channel position with the decoded TV sta-
tion manually. See next page.
Note:
• The built-in timer stores 8 memories.If the
“PROGRAM FULL” indicationappears,
you must delete one memory (see page
34).
....to be continued to next page
• If you wish to receive the suitable pro-
gram with a satelite receiver, the AV-po-
sition must be given near “CH”.
Press AUX repeatedly until AV2 appears.
• After a power failure or disconnection of
the power plug, all programmed record-
ing settings and time display will be lost
upon resumption of power. In this case,
reset the clock (see pages 19) and re-
program any timer recordings.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
®
SHOWVIEW -Recording
Example:You receive NBC on program position 12.
In case of the first SHOWVIEW-recording for NBC, 2 bars
will blink at the CH-line. Enter 12 with number keys.
Press 1 and then 2 within 2 seconds (if the 2-press was
too late, the display 1 will be replaced with 2). The
SHOWVIEW-system memorizes that the storing position
12 is for NBC. From the next all times of the SHOWVIEW-
recording from NBC, the 12 will be entered in the “CH”-
line automatically. In case of an erroneous input for the
VPS/PDC:
Switch the VPS/PDC on or off. Be sure to pay attention
to the VPS/PDC-important note on page 35.
Press
line.
or
repeatedly until you reach VPS/PDC-
Then press
or to select “ON” or “OFF”.
Press OK after the
confirmation. Then
press SET UP MENU
repeatedly until the TV-
picture appears.
15 TUE 17:30 18:00
SP
-
------ --:--
--:--
-7-V
--
--
--
--
--
--
5
------ --:--
------ --:--
------ --:--
------ --:--
------ --:--
------ --:--
-
--:--
--:--
--:--
--:--
--:--
--:--
channel number, press
to go in the “CH”-line and
-
-
enter the correct number again.
-
-
-
Press
/
or number
SELECT
EXIT
:
/ OK
SHOWVIEW NO . 327741029
To enter the other
program repeat the
steps 1 - 5.
: MENU
DATE
START
END
15 TUE
17:30
18:00
12 NBC
SP
keys to enter the program
position number.
Then press
CH
SPEED
.
VPS/PDC OFF
SELECT :
Press •. The clock symbol ( ) will appear on the
display and the VCR stands by for recording. At the
same time, VCR mode will change to DVD mode
automatically.You can use DVD even if the VCR is
in the Timer recording mode.
SET
:
/ 0–9
6
EXIT
: MENU
OK : OK
Setting a day of the week:
You have selected DAILY or WEEKLY in step 3, then
you can select recording date again.The date must blink
as 2 bars.
If you do not use the DVD, turn the power off.
The timer recording will start at 5 seconds before
the time you predetermined.
If it does not blink, then press
the DATE blinks. Then press
the desired date appears.
or
or
repeatedly until
repeatedly until
Note:
• If the clock symbol ( ) does not appear on the
display in spite of the pressing of •, the cassette
may not have been loaded yet.(see page 22)
• If the cassette is ejected in spite of the pressing
of •, the erase prevention tab of the cassette may
have been removed. (see page 22)
The following date are stand for your selection: SUN-
SAT: all dates from Sunday to Saturday, or MON-SAT:
only dates from Monday to Saturday, or MON-FRI: only
dates from Monday to Fryday.WKL-MON:each Monday,
WKL-TUE: each Tuesday, ..., WKL-SUN: each Sunday.
• If the clock symbol ( ) blinks when the timer re-
cording ended, the TV program has not been com-
pletely recorded because of an insufficient tape sup-
ply. In this case, press • to cancel the timer pro-
gram or press EJECT to remove the cassette tape.
• During timer recording standby mode, the VCR
mode cannot be selected.To use the VCR, press
• at first, then press VCR to change toVCR mode.
After you use the VCR, press • again to put the
VCR into timer recording standby mode.
Change the recording start-time:
The recording start-time will be set by SHOWVIEW
automatically. However you can change the recording
start-time manually. The time near START must blink.
If it does not blink, press
time blinks. Then press
or
repeatedly until the
to change.
Recording period extension:
The recording end-time will be set by SHOWVIEW
automatically. However you can extend the recording
end-time manually. The time near END must blink.
• If you press • during timer recording, the record-
ing operation will be interrupted. If you press •
again within the programmed time, the recording
operation will start again.
If it does not blink, press
time blinks. Then press
or
repeatedly until the
to extend.
Select Tape speed:
Select the recording tape speed Standard Play (SP) or
Long Play (LP).
Press
Then press
or
repeatedly until you are in SPEED-line.
or to select “SP” or “LP”.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer-Recording
Timer recording can be programmed
on the TV-screen with the remote
control. The built-in timer allows
automatic unattended recording of up
to 8 programs within 1 month.
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press VCR to select the VCR mode. (The VCR indicator will light)
• Load a video cassette with the erase prevention tab intact. Make
sure with OSD that the time and date are correct. (see page 29).
Example: Timer recording for channel 1, 13:00 to 14:30 with Tape
speed LP on timer program number 1.
Press SET UP MENU. Press
1
ATS (AUTO TUNING SYSTEM)
or
to select TIMER REC SET.
TIMER REC SET
VCR EXTENSION
VCR SETUP
Then press OK.
CHANNEL SETUP
SYSTEM SETUP
SELECT
:
ENTER : OK
EXIT
: MENU
Each line stand for one program
of the 8 memories. Select one
2
3
4
------
--:--
--:--
--:--
-- -
--:--
--:--
--:--
--:--
--:--
--:--
--:--
--:--
------
------
-
--
-- -
-- -
-- -
line with
or
. Then press
------ --:--
------ --:--
------ --:--
------ --:--
------ --:--
SELECT :
EXIT : MENU
OK.
-
--
-- -
-- -
/ OK
Set the desired date with
or
TIMER REC SET
or number keys.Then press
to accept it.
DATE
START
END
23 MON
11:30
--:--
3 TV3
SP
CH
SPEED
VPS/PDC
OFF
SELECT :
SET
:
/ 0–9
EXIT
: MENU
Set the Starting time (13:00),
ending time (14:30), channel (1
ARD), Tape speed (LP) and
VPS/PDC (P.35) in the same way
as the step 3.
TIMER REC SET
DATE
23 MO
START
END
13:00
14:30
1 ARD
LP
CH
SPEED
VPS/PDC
ON
SELECT :
• In case of an erroneous input
SET
:
EXIT
: MENU
OK : OK
press
to go back to before
step and enter again.
Note:
....to be continued to next page
In the event of a power failure the data of
the automatic recording will be maintained
in the built-in memory for about 30
minutes. Also, the clock will continue to
run for this period of time. Thereafter the
data will be deleted. When the power
resumes, the time display will change to
“--:--” that the timer setting will have to be
set.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer-Recording
Press OK to accept them.
In case of Timer progarms-overlapping
5
23
13:00 14:30
LP
-
---M-O--N --:-- --:-- -1-V
------ --:-- --:-- --
------ --:-- --:-- --
------ --:-- --:-- --
------ --:-- --:-- --
------ --:-- --:-- --
------ --:-- --:-- --
-
• Do not overlap timer programs as portions of the con-
flicting programs will be lost. The first recording time
has priority over the next recording time as shown in
the diagram below.
To enter other programs,
repeat steps 2 through 4.
-
-
-
-
-
SELECT :
/ OK
• To return to the normal
screen, press SET UP
MENU twice.
EXIT : MENU
8 : 00
9 : 00
10 : 00
11 : 00
Program 1
Program 2
Deleted Parts
Press •. The clock symbol ( ) will appear on the
display and the DVD/VCR stands by for recording.
At the same time, VCR mode will change to DVD
mode automatically. You can use DVD even if the
VCR is in the Timer recording mode.
6
Program 3
Non Recorded Portion Parts
Recording
Control Settings
Prog.1
Prog.2
Prog.3
Note:
• The daily/weekly recording can be made continuously
until the recording is canceled or the tape reaches
the end.
• During timer recording the automatic rewinding
mechanism does not function.
If you do not use the DVD, turn the power off.
• If the clock symbol ( ) blinks in the display in
spite of the pressing of •, the cassette may not
have been loaded yet. (see page 22)
• If the cassette is ejected in spite of the pressing
of •, the erase prevention tab of the cassette may
have been removed. (see page 22)
Confirmation/Cancellation of the Timer
Recording
If the Timer has been activated, now press • to
deactivate the Timer. The clock symbol ( ) will
disappear.Then press VCR to change toVCR mode.
1
Note:
• In case of the timer recording from the scart socket,
proceed as follows: In step 4 press
or
repeat-
edly until the "CH" line blinks. Then press AUX re-
peatedly until "AV1" or "AV2" or "AV3" appears.
• If the clock symbol ( ) blinks when the timer record-
ing ended, the TV program has not been completely
recorded because of an insufficient tape supply.Press
• to cancel the timer program or press EJECT to
remove the cassette tape.
• During timer recording standby mode, the VCR mode
cannot be selected.To use the VCR, press • at first,
then press VCR to change to VCR mode. After you
use the VCR, press • again to put theVCR into timer
recording standby mode.
Press PROG. twice. All the
8 Timer memories will
appear.
2
15 TUE 17:30 18:00 7V SP
23 MON 13:00 14:30 1V LP
25
12:15 13:00
4
---W--E-D --:-- --:-- --
------ --:-- --:-- --
------ --:-- --:-- --
------ --:-- --:-- --
------ --:-- --:-- --
SP
-
-
-
-
-
SELECT :
CLEAR : CANCEL EXIT : MENU
/ OK
To
correct
the
3
4
TIMER REC SET
DATE
23 MO
13:00
14:30
programmed setting:
Press or to select the
program you wish to correct,
then press OK to enter the
program input mode. Then
START
END
CH
1
ARD
SPEED
VPS/PDC
LP
ON
SELECT :
SET
:
/ 0–9
EXIT
: MENU
OK : OK
press
or
to select the
Timer Recording Special case
item you wish to correct.
Then correct the data with
Weekly (e.g. WKL-TU: each Tuesday) or daily (e.g.
MON-SAT: Monday to Saturday) Timer recording
Follow the procedure for timer recording on both pages
or
.
before. At picture 3 press
desired setting appears.Then press .When you press
or repeatedly, the indicator at DATE will change
as follows, in case today is Friday.
or
repeatedly until the
To cancel Timer program:
Press or to select the
written line. Then press
CANCEL. This line is now
canceled.
------ --:-- --:-- --
-
23 MON 13:00 14:30 1V LP
25
12:15 13:00
4
---W--E-D --:-- --:-- --
------ --:-- --:-- --
------ --:-- --:-- --
------ --:-- --:-- --
------ --:-- --:-- --
SP
-
-
-
-
-
One month later
minus one day
SELECT :
/ OK
EXIT : MENU
SUN-SAT
MON-SAT
25 FRI ..... 24 SUN
MON-FRI
WKL-FRI
Press SET UP MENU (or PROG.) repeatedly until
the TV-picture appears.
WKL-THU.....WKL-SAT
MON-SAT = everyday from
Monday fo Saturday.
WKL-SAT = each Saturday
TIMER REC SET
DATE
WKL-WED
START
END
11:30
--:--
CH
2
ZDF
SPEED
VPS/PDC
SP
ON
SELECT :
SET
:
/ 0–9
EXIT
: MENU
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Detailed Description of the VPS/PDC Function
VPS/PDC is a service provided by the public TV station. When you select a VPS/PDC-compatible TV station and
activate the VPS/PDC function, the beginning and the end of the timer recording will be controlled by the TV
station. Any program air time delays will be taken care of.The private TV companies have not provided this service
yet. Thus, please turn OFF the VPS/PDC function when performing timer recordings of programs aired by private
TV stations.
Example: Assume you want to record a sports event that is scheduled to be aired from 21:00 to 23:00 and perform
your timer programming accordingly. However, the beginning of the sports event is postponed to 21:30 so that the
program will now end at 24:00. Using the VPS/PDC function, you can still make sure that the entire TV program is
recorded.
21
23
24
22
The user’s timer programming setting:
Actually, however, the sports event is aired from 21:30 to
24:00.
Recording without VPS/PDC function:
Recording with VPS/PDC function:
When you perform the timer programming be sure to observe the following points:
1.) Date and time should be correctly set.
The following points from 2 to 5 will be automatically taken care of by the ShowView feature.
Therefore, be sure to keep them in mind when doing recordings without the ShowView feature.
2.) Set the starting time precisely to the minute according to the data in the TV program magazine (not a
single minute earlier or later); otherwise an automatic recording will not be possible.
3.) If an additional 2nd time is specified in parentheses, which in most cases is explicitly stated as “VPS/PDC
time”, make sure to enter only this time data.
4.) The starting time of the subsequent TV program is considered to be the end time of the recording.
5.) If you program the recording of several subsequent TV programs, enter the start and end times sepa-
rately for each TV program. It is not sufficient to solely enter the start time of the first and the end time of the
last program (in this case only the first program will be recorded unless the VPS/PDC function is turned off).
Please look up in your TV program magazine which TV stations transmit the VPS/PDC signal. A VPS/PDC
on-screen indication (during auto search) does not mean that the respective TV station is actually VPS/PDC-
compatible. Therefore, make sure to turn OFF the VPS/PDC function if you want to make timer recordings of
programs aired by a station that is not VPS/PDC-compatible. Otherwise the TV program will not be recorded
in its entirety.
It is preferable to deactivate the VPS/PDC function even for VPS/PDC-compatibleTV stations — at least it
simplifies the programming procedure — if you want to record several programs of the sameTV station in
direct sequence.
For instance: at 20:00, recording of the “Tagesschau” news program,
subsequently, at 20:15, recording of a movie,
and subsequently, from 21:45 to 22:45, recording of a sports program.
Using the VPS/PDC function, enter the start and end times of each program
separately;however, if theVPS/PDC function is turned OFF, it will be sufficient
to enter the start time of 20:00 and the end time of 22:45.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
NICAM/German A2 Stereo Recording and Playback
This DVD/VCR is capable of recording
sound in Hi-Fi system. The recording
will be performed automatically.
NICAM STEREO broadcasts are
recorded in its original sound system
regardless of the setting. If you wish
to record NICAM programmes, select
NICAM "AUTO" as follows.
And, this DVD/VCR can also receive
and record German A2 stereo
program.The tape recording is always
both in HiFi and in MONO on the
standard longitudinal track. In case of
bilingualTV programs always the two
audio channels will be recorded.
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press VCR to select the VCR mode. (The VCR indicator will light)
NICAM stereo sound reception:
Press SET UP MENU. Press
ꢀ or M to select VCR SETUP.
Then press OK.
ATS (AUTO TUNING SYSTEM)
TIMER REC SET
VCR EXTENSION
VCR SETUP
CHANNEL SETUP
SYSTEM SETUP
1
SELECT
ENTER
EXIT
:
:
:
OK
MENU
Press ꢀ or M to select NICAM.
VCR SETUP
2
NICAM
AUDIO MIX
SHARPNESS
[AUTO]
[OFF]
Then press
/
or OK to
select [AUTO].
/
SELECT
ENTER : OK
MENU
:
EXIT
:
Press the SET UP MENU repeatedly until the TV picture
3 appears.
NICAM programmes are divided into 4 types as
shown below.
NICAM STEREO broadcast
"NICAM ST" illuminates when a
NICAMSTEREObroadcastsignalis
NICAM ST
received.
NICAM MONO A broadcast
"NICAM M1" illuminates when a
NICAM MONO A broadcast signal is
NICAM M1
received.
NICAM MONO A B broadcast
"NICAM M1/2" illuminates when a
NICAM MONO A and MONO B
NICAM M1/2
broadcast signal is received.
Note:
When listening to a stereo broadcast or
playing back a tape Hi-Fi recorded in
stereo, you have to connect the DVD/
VCR with the stereo audio system or the
stereo TV. The sound which is output
from the RF OUT jack is monaural.
NICAM OFF
It will be displayed for the NICAM
signal when the "NICAM [OFF]" is
selected in menu screen.
NICAM OFF
36
Download from Www.Somanuals.com. All Manuals Search And Download.
NICAM/German A2 Stereo Recording and Playback
German A2 stereo sound reception:
Stereo program indication
It will be displayed for approx. 4
seconds when stereo programs
are being received.
STEREO
Bilingual program indication
It will be displayed for approx.
4 seconds when bilingual pro-
grams are being received.
BILINGUAL
Playback
Use A.MONITOR to select under stereo/mono or bilingual
playback. See the table below for more information.
On-screen indications
(for 4 sec.)
Bilingual playback
performed as follows:
Stereo playback
performed in:
Simultaneously
both languages
from HiFi track
(Mixed sounds)
Stereo
Left channel signal One's mother
output from both
loudspeakers
tongue dubbing
(Main sound)
L
CH
Right channel
Original sound
signal output from
both loudspeakers
track (Sub sound)
R
CH
Mono
One's mother
tongue dubbing
(Main sound)
HiFi signal indication
It will be displayed for approx. 4
secondswhenplayingHiFivideo
cassette tapes.
Note:
WhenplayingHiFicassettetapesrecorded
on another VCR, the sound output may be
distorted. This is normal and no indication
ofaunitmalfunction.Trytominimizesound
distortions by using SET +/– or change to
MONO by pressing of A.MONITOR.
HI-FI
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Mixing
Preparation:
When playing audio dubbed video
tapes, press A.MONITOR to select the
sound you want to listen to. Press
A.MONITOR repeatedly until "MONO"
isdisplayedonthescreentolistenonly
to the dubbed sound. In case of the
other on-screen indications only the
original sound will be output. It is also
possibletolistentothedubbedandthe
original sounds simultaneously. To
accomplish this, set "AUDIO MIX" to
"[ON]" (see right). During playback,
press A.MONITOR repeatedly until
"STEREO" is displayed on the screen.
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press VCR to select the VCR mode. (The VCR indicator
will light)
Press SET UP MENU.
Press
VCR SETUP. Then press
1
ATS (AUTO TUNING SYSTEM)
or
to select
TIMER REC SET
VCR EXTENSION
VCR SETUP
CHANNEL SETUP
SYSTEM SETUP
OK.
SELECT
:
ENTER : OK
EXIT
: MENU
Press
or
to select
2 AUDIO MIX.
VCR SETUP
NICAM
AUDIO MIX
SHARPNESS
[AUTO]
[OFF]
SELECT :
/
ENTER : OK
MENU
EXIT
:
Press
/
or OK to select
VCR SETUP
3 [ON].
NICAM
AUDIO MIX
SHARPNESS
[AUTO]
[ON]
If you select "[ON]", you can
listen to the dubbed and the
original sounds at the same
time.
SELECT :
/
ENTER : OK
MENU
EXIT
:
Press SET UP MENU repeatedly until the TV picture
4 appears.
Note:
To deactivate the AUDIO MIX function
follow the above procedure from step 1 to
3, select "[OFF]", and confirm the setting
by pressing SET UP MENU.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Duplicating a Video Tape
When you try to connect with a cable, make sure the power of both units have been turned off.
Connect the recording unit with the TV. Therefore you can just watch what the recording unit is recording.
Load a blank cassette tape with the erase prevention tab
While holding 2, press
and then 4 of Recording unit.
3
4
1 intact into the recording DVD/VCR. Load the previously
recorded cassette tape into the playback VCR or a video
camera.
Press PLAY-button and then PAUSE/STILL-button of
Playback unit. Now you can see the still picture of the
scene that you wish to duplicate.
VCR
Press 4 of both units simultaneously to start the Duplicat-
5 ing.
Use AUX or PR of the recording DVD/VCR to select the
2 "A1", "A2" or "A3" instead of the preset channel.
Note:
A1 = TV-RGB/Composite Scart Socket
A2 = VCR/DECODER Scart Socket
A3 = Front AV jacks
Beforestartingtheduplicatingprocess,selecttheproper
tape speed using
correct tape speed will be set automatically during
playback.
. For a pre-recorded tape the
Connection with second Video recorder or Video camera
VCR/DECODER
(not supply)
SCART socket
OR
Playback on
camera
Playback unit
Recording unit
Recording unit
Playback unit
HR-XV1EU
TV-Scart socket
(not supply)
(not
supply)
TV
SYSTEM SETUP
CLOCK SET
LANGUAGE/SPRACHE/LANGUE
AV2
[AV]
• Select the “AV2” in menu
screen in the same way as the
step 1~2 on page 14.
Then press OK to select AV
mode.
SELECT
ENTER
EXIT
:
:
:
/
OK
MENU
(not supply)
Press AUX on the
recording unit repeatedly
until A3 appears.
Duplicating a disc material onto a video tape
You can record disc material in DVD, Video CD, Audio CD, etc. onto a video tape with this DVD/VCR only.
If the DVD disc has a Copy-guard feature, the duplicating is not possible. A symbol mark “
” will appear
on the screen for approx. 4 seconds. See page 42 for more information about the DVD playback.
Preparation:
• Load a cassette tape with the erase prevention tab
intact.
During disc playback, while holding 2, press
.
3
• Select the tape speed in the VCR mode. (see P.28)
• Load a disc you wish to duplicate.
Note:
Press DVD to select the DVD mode. (The DVD indi-
cator will light)
1
You can set the duplicating time using the ITR-function.
At step 3 above press 2 repeatedly until the desired
duplicating time appears on the screen.(P.30)
Press
to start the disc playback.
2
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc
This unit applies to DVD discs from Region 2 only.
The loaded Disc (DVD, Video-CD, Audio-CD and MP3-CD) will be recognized automatically.
The suitable Disc-formats are: DVD, CD-R and CD-RW.
Some CD-R/RW discs may be incompatible.
This DVD/VCR uses the PAL color system. The NTSC-DVDs can be playback on PAL 60Hz.
Do not play DVD-ROM, DVD-Audio, CDV, CD-G or Photo CD to prevent accidental erasure of prerecorded material.
Some DVDs is played back with a Copy guard system. In case of a dubbing on video tape, strong disturbance may
occur. This is not a defect of this DVD/VCR.
DVD DISC
Title
TITLE1
CHAPTER 1
TITLE2
When two or more movies are recorded on a disc,
the disc is divided into two or more sections. Each
section is called a “TITLE”.
CHAPTER 2
CHAPTER 1
CHAPTER 2
CHAPTER 3
Chapter
The titles can be subdivided into many sections.
Each section is called a “CHAPTER”.
Audio-CD
Track
TRACK
1
TRACK
2
TRACK
3
TRACK
4
TRACK
5
An Audio CD can contain several items.
These are assigned to the tracks.
Removing Disc from Case
Be sure to hold the edge of disc. Do not touch the surface of the disc.
Pick up the disc gently from the case.
• Do not scratch the disc.
• Do not get dirt on the surface of the disc.
• Do not stick a label or adhesive tape on the disc.
• Do not drop or bend the disc.
Storing Disc
• Store the disc in the case to avoid risk of scratches, dirt or damage.
• Do not leave disc exposed to direct sunlight or in hot or humid places.
Cleaning Disc
Wipe the disc with a clean, dry cloth from center to edge.
• Do not wipe the disc round.
• Do not use liquid or aerosol cleaners.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting setup language
The setup language can be selected.
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
• When using an amplifier, switch on the amplifier.
Press DVD to select the DVD
1
mode. (The DVD indicator will
light.)
“No Disc” will appear on the
screen. (If a DVD disc has al-
ready loaded, the playback will
No Disc
start automatically.)
PressSETUPMENU inthestop
2
mode. The SETUP MENU of
Picture
DVD will appear on the screen.
TV Shape 4:3LB
Video Out Select Video
Then press
or
to select
“Language”.
: Select
: Enter
Press
/
toselectOn-Screen
3
Language, then press OK (En-
ter).
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
Subtitle Language
ENG
ENG
: Select
: Enter
Press
/
to select desired
4
5
C
language: English (English),
German (Deutsch) or French
(Français).
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
Subtitle Language
ENG
ENG
: Select
: Enter
To make the SETUP screen disappear, press SET UP MENU
(or RETURN).
If the DVD/VCR does not operate
properly: Static electricity, etc., may
affect the player's operation.Disconnect
the AC power cord once, then connect
it again.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback procedure
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press DVD to select the DVD mode. (The DVD indicator will light)
Press OPEN/CLOSE.
1
The disc tray will open.
Place a disc onto the tray.
2 Hold the disc, position it with the
printed label side up, align it with
the guides, and place it in its
proper position.
Press
or OPEN/CLOSE.
3
4
The disc tray closes automati-
cally.
On the screen,
changes to
“
” and then playback will
commence.
• A menu screen may appear on
the TV screen, if the disc has
a menu feature. In this case,
press
,
,
,
or OK to
operate a menu feature.
Press 3 to end playback.
• The DVD/VCR memorizes the stopped point, depending on
the disc. “To Return To The Last Scene Viewed, Press Play. To
Disable This Operation, Press STOP Again.” appears on the
screen for approx. 4 seconds. “ ” will continue blinking in the
display until the playback is stopped completely. Press
resume playback (from the scene point).
to
• If you press 3 again (“ 3 ” appears on the screen) or unload
the disc, the DVD/VCR will clear the stopped point.
Then press OPEN/CLOSE.
5 The disc tray opens.
Remove the disc and press
, (POWER).
The disc tray closes automatically and DVD/VCR turns off.
NOTES:
• If a non-compatible disc is loaded, "Please Check Disc", "Disc playback unauthorized Consult owners manual
for further information" or "Parental Lock" will appear on the TV screen according to the type of loaded disc. In
this case, check your disc again (See pages 40 and 50, 51).
• Some discs may take a minute or so to start playback.
• A “Prohibition” symbol
may appear at the upper right of the screen.This symbol means either the feature you
tried is not available on the disc, or the DVD/VCR can not access the feature at this time.This does not indicate
a problem with the DVD/VCR.
•
When you set a single-faced disc label downwards (ie. the wrong way up) and press
or OPEN/CLOSE, "
"
will appear and remain on the screen for approx. 30 seconds and then it will change to "Please Check Disc".
• Some playback operations of DVDs may be intentionally fixed by software producers. Since this DVD/VCR plays
DVDs according to the disc contents the software producers designed, some playback features may not be
available. Also refer to the instructions supplied with the DVDs.
• When playing DTS-encoded Audio CDs, excessive noise will be heard from the analog stereo outputs.To avoid
possible damage to the audio system, the consumer should take proper precautions when the analog stereo
outputs of the DVD/VCR are connected to an amplification system.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Special playback
Note: There may be a slight delay be-
tween pressing the button and the
function activation.
Fast Forward Playback
Press
during normal playback.
Each press of
will increase the speed of the search x2 ( ), x8
(
(
), x30 (
) are available)
), x100 (
). (in case of Audio-CD: x4 ( ) and x8
• To resume normal playback, press
.
Review Playback
Press
during normal playback.
Each press of
will increase the speed of the search x2 ( ), x8
), x100 ( ). (in case of Audio-CD: x4 ( ) and x8
(
(
), x30 (
) are available)
• To resume normal playback, press
.
Still Playback
Press 4 during normal playback.
To resume normal playback, press
.
Frame Advance
Press 4 during still playback.
One frame is advanced each time
you press 4.
To resume normal playback, press
.
Slow-motion Playback
Press SLOW during normal playback or still playback.
Each press of SLOW will change the speed of the slow x1/2, x1/4,
x1/8.
NOTES:
• The unit is capable of holding a still
video image or On screen display image
on your television screen indefinitely. If
you leave the still video image or On
screen display image displayed on your
TV for an extended period of time, you
risk permanent damage to your
television screen. Projection televisions
are very susceptible.
• To resume normal playback, press
• To resume the still playback, press 4.
.
Locating a chapter or track
T
1
C
1
Press SKIP (
) Forward or SKIP
(
) Reverse during playback to
• Some titles may not display chapter
numbers.
locate a chapter or track that you
want to watch.
Each time you press the button, a
“C (chapter)” number or “T (track)”
number is skipped.
• When you set “Title Stop” to “Off” (See
page 57), you can access chapter in
another title. If you go back to the
preceding title by pressing the SKIP, the
DVD/VCR locates the first chapter of the
title. When “Title Stop” is set to “On”.
you can access chapters only within the
current title.
When you press SKIP (
), playback starts from the beginning
of the current chapter or track.
When you press SKIP (
) twice, playback starts from the
beginning of the preceding chapter or track.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Picture Signal Selection/Zooming
Preparation:
You can select the output signal of
DVD playback picture to the TV
screen as an VIDEO signal or a RGB
signal.
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator
will light)
Press SET UP MENU in the
stop mode.
1
Picture
TV Shape 4:3LB
Video Out Select Video
Press
ture”, then press
or
to select “Pic-
or to
select “Video Out Select”.
: Select
: Enter
Press OK (Enter).
2
Press
or
to select the
Picture
desiredpicturesignal,“Video”
or “RGB”.
TV Shape 4:3LB
Video Out Select Video
Video
RGB
: Select
: Enter
To make SETUP screen disappear, press SET UP MENU.
3
Note:
• If you use the connection with S-Video cord, be sure to set the
“Video Out Select” at step 2 above to “Video”. If you select
“RGB”, the TV screen will be disturbed.
• If you selected “RGB” at step 2 above, press TV/VCR to select
VCR. (VCR indicator will appear on the display) Otherwise,
the TV screen will be disturbed when you select the channel
with TV’s CHANNEL UP/DOWN buttons.
Zooming
This unit will allow you to zoom in on the frame image. You
can then make selections by switching the position of the
frame.
PressZOOMduringplayback.
1 The center part of the image
will be zoomed in.
As you repeatedly press the
ZOOM
EXIT
OKorZOOMwhile“ZOOM”is
selected, the magnification
levelchanges.Variationofthe
Zoom Off
: Select
: Change
levels includes image reduc-
tion.
Note:
Press
/
or
/
to view a different part of the frame.
2 You may move the frame from the center position to UP,
• Picture Signal Selection is only avail-
able for connecting with a 21 pin Scart
Cable.
DOWN, LEFT or RIGHT direction.
• Depending on your TV, NTSC disc may
not playback correctly in colour. In this
case, it is recommended to select the
Picture Signal RGB on step 2.
• Only use RGB setting if your TV is RGB
compatible.
• If you select “EXIT” and press the OK, you can turn off the
symbol mark, keeping the current magnification level.
• Press CANCEL to restore the zoom point to the center
of the picture.
While “ZOOM” is selected, press ZOOM repeatedly to re-
turn to a 1:1 view.
3
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat playback
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator
will light)
REPEAT PLAYBACK
Press PLAY MODE repeatedly to select “Chapter Repeat”,
1 “Title Repeat” or “All Repeat”. (In case of CD, select “Track
Repeat” or “ ALL Repeat” )
DVD
CD
Chapter Repeat
Track Repeat
During playback repeat playback will start automatically.
2
To start repeat playback during stop mode, press
about 5 seconds after you press PLAY MODE.
• To resume normal playback, press PLAY MODE repeatedly
until “Off” appears on the TV-screen.
within
A-B Repeat Playback
A-B repeat playback allows you to repeat material between two
selected points.
Press REPEAT A-B during
playback.
The start point is selected.
1
A
-
Press REPEAT A-B again.
2
The end point is selected.
Playback starts at the point that
you selected. Playback stops at
the end point, returns to Point A
automatically, then starts again.
A
-B
To resume normal playback,
press REPEAT A-B again.
NOTES:
•
•
•
•
Some discs may not work with the
repeat operation.
“Repeat Off” appears on the screen.
In A-B repeat mode, subtitles near
point A or B may not appear.
During the A-B Repeat Playback the
ANGLE feature will not operate.
You may not be able to set A-B Re-
peat, depending on the scenes of the
DVD.
•
•
A-B repeat does not work with an in-
teractive DVD and MP3-CD.
Random playback can not be com-
bined with Repeat playback.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory playback/Random playback
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press DVD to select the DVD mode. (The DVD indicator will light)
Memory playback
You can arrange the order of titles, chapter or tracks on the disc.
Press MEMORY.
In stop mode
In playback
1
2
1
2
3
4
5
6
7
T:-- CT:---
T:-- CT:---
T:-- CT:---
T:-- CT:---
T:-- CT:---
T:-- CT:---
T:-- CT:---
1
T:-- CT:---
Memory
Memory
: Select 0-9 : Input
: Play
: Select 0-9 : Input
: Play
Press
/
to
In stop mode
In playback
select “T” Title
number or “CT”
Chapter or Track
number. Use
number keys to
Input the favorite
number.
1
2
3
4
5
6
7
T:01 CT:002
T:-- CT:---
T:-- CT:---
T:-- CT:---
T:-- CT:---
T:-- CT:---
T:-- CT:---
1
T:01 CT:002
Memory
Memory
: Select 0-9 : Input
: Play
: Select 0-9 : Input
: Play
• If you input a large number than the number that is recorded
on the disc, the bar will be skipped.
• The input number into "T" for CD or MP3 is not effective.
Press or OK.
Set the “T” and
“CT” in the next
bar as In step 2.
In stop mode
In playback
3
4
1
2
3
4
5
6
7
T:01 CT:002
T:02 CT:004
T:-- CT:---
T:-- CT:---
T:-- CT:---
T:-- CT:---
T:-- CT:---
2
T:02 CT:004
Memory
Memory
: Select 0-9 : Input
: Play
: Select 0-9 : Input
: Play
• When you select another chapter In the same title, you do
not need to select the title number.
• To cancel the programmed selection, press CANCEL.
Press
to start MEMORY playback.
• To resume normal playback, press CANCEL.
Random playback
Press PLAY MODE repeatedly to select “ Chapter Random”
or “Title Random”.(In case of CD, select Track Random)
1
NOTES:
The memory playback is cancelled
•
DVD
CD
when press
playback.
3
during memory
• Random playback can not be
combined with Repeat playback.
• You can program up to 30 selections
into the memory.
Chapter Random
Track Random
• Depending on the DVD, Chapter
Random operation may not work
during playback.
• You cannot use the random playback
with memory playback.
During playback random playback will start automatically.
2
To start random playback during stop mode, press
about 5 seconds after you press the PLAY MODE.
• To resume normal playback, press PLAY MODE repeatedly
until “Off” appears on the TV-screen.
within
46
Download from Www.Somanuals.com. All Manuals Search And Download.
MP3 Playback
This player can play back the MP3-data
which has been recorded on CD-R or CD-
RW. To produce the MP3-data, you need a
Windows-PCwithCD-ROMdriveandaMP3-
encoding Software (not supplied).
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator
will light)
The Apple-HFS-System can not be played.
Press OPEN/CLOSE.
1
The disc tray will open.
Place a disc onto the tray.
MP3 CD Information
Limitations on MP3 CD playback
• MP3 CD is the disc that is standardized by
ISO9660, its file name must include 3-digits
extension letters, “mp3”.
• The directory and file names of the MP3
CD must correspond to the ISO
Press
or OPEN/CLOSE. The
disc tray closes automatically. On
the TV-screen, “ ” and then
2
3
T
11
reading file number will appear.
Then playback will commence.
• Reading will take as much time
as the number of file.
standardized files.
• This unit can read 200 files per disc. If
one directory has more than 200 files, it
reads up to 200 files, the remaining files will
be omitted.
• As for multi-session disc, only the first
session can be played.
• If the CD has both audio tracks and MP3
files, only audio tracks are played.
• It may take more than one minute for this
unit to read MP3 files depending on its
structure.
• Press 3 to end playback.
Press OSD.
MP3
T
1
000:23
Then press
/
to select
MP3
and press OK (Enter).
PCM
: Select
: Enter
• Music recorded by “Joliet Recording
Specification” can be played back, the file
name is displayed (within 8 letters) on the
screen. Long file names will be condensed.
• The music files recorded by “Hierarchical
File System” (HFS) cannot be played.
Press
/
or
/
to select the desired track, then press
4 OK (Enter). Track is selected and play commences.
•
In case the folder includes more than 9 tracks, press
to display next track list.
/
• To remove track list, press CANCEL.
• Press to select “T” and press number keys to
input your desired track.
Limitations on display
/
The maximum number for display is 8
letters. Available letters for display are the
following: capital or small alphabets of A
through Z, numbers of 0 through 9, and _
(under score).
MP3
T
1
000:23
~
1. \ CRYINI
2. \ DANGER
1
~
1
3. \ GITARREN
~
4. \ LILYWA
1
~
PCM
5. \ MERCYS
1
~
~
6. \ OBSESS
1
1
1
7. \ PINKPA
~
8. \ RUNNIN
Notes on MP3 files
: Select
: Search
To play back MP3 CD in the recorded order,
1. Use MP3 software that records data
alphabetically or numerically.
2.Name each file including a two-digit or three-
digit number (e.g. “01” “02” or “001” “002”).
3. Refrain from making too many sub-folders.
Press 3 to end playback.
• The unit records the stopped track.
5
6
Press
track).
to resume playback (from the beginning of
• If you press 3 again or unload the disc, the unit will clear
the stopped track.
CAUTION:
• Some MP3 CDs can not be played back
depending on the recording conditions.
• The CD-R/RW that has no music data or
non-MP3 files can not be played back.
Press OPEN/CLOSE.
The disc tray opens.
Remove the disc and press
The disc tray closes automatically and DVD/VCR turns off.
.
NOTES:
•
During MP3-Playback, you can not use SEARCH, A-B
Repeat functions.
•
You can use Repeat(Track or All) and Random functions for
MP3 CD Playback.(See page 45 and 46)
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing soundtrack language / Changing Subtitles language
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press DVD to select the DVD mode. (The DVD indicator will light)
Changing soundtrack language
You can select the language when you play a multilingual disc.
Press A.MONITOR during play-
back.
Thecurrentsoundtracklanguage
is displayed.
1
ENG1
ENG2
FRE1
2CH
5.1CH
2CH
Audio:FRE1
: Select
2CH
: Return
2CH
Press A.MONITOR repeatedly
2 until the desired language is se-
ENG1
ENG2
FRE1
2CH
5.1CH
2CH
lected.
The on-screen display will disap-
pear after a few seconds.
• To turn off the soundtrack
setting display, press the
CANCEL or OK button.
Audio:ENG1
: Select
2CH
2CH
: Return
In case of VIDEO CD playback
AudiotypechangesasfollowseachtimeyoupressA.MONITOR.
NOTES:
• If the desired language is not heard after
pressing A.MONITOR several times, the
language is not recorded on the disc.
• Changing soundtrack or subtitle
language is cancelled when you open the
disc tray or turn the power off.The initial
default language or available language
will be heard and seen if the disc is
played back again.
Changing Subtitles language
You can select the language when playing back a disc recorded
with multi-lingual subtitles.
Press SUB TITLE during
playback.
1
Off
GER 1
Then press
/
to select the
DUT
SV
NO
1
1
1
•
Depending on the DVD you may be
unable to turn on, turn off, or change the
subtitles, even if they are recorded on the
disc. While playing the DVD, the subtitle
may change while opening or closing the
disc tray, or while changing the title.
During some scenes, the subtitles may not
appear immediately after you select“On”.
desired language.
• To turn off the subtitle setting
display, press the CANCEL
or OK button.
Subtitle:--- Off
: Select
: Return
• To turn the subtitles off, select
“Off”.
•
Press SUB TITLE repeatedly to
turn Subtitles on or off.
2
• The abbreviation of the language
appears instead of the language name.
Refer to the list of languages and their
abbreviations. (See on page 61.)
Off
ENG 1
SPA 1
FRE 1
Subtitle:ENG1 On
: Select
: On/Off
: Return
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing angles / Title selection / DVD menu
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press DVD to select the DVD mode. (The DVD indicator will light)
Changing Angles
When playing back a disc recorded with multi-angle facility, you
can change the angle that you are viewing the scene from.
Press ANGLE during playback.
1
The current angle will appear.
1
2
3
Angle :1
: Select
: Return
Press ANGLE or
selected.
• To turn off the angle number display, press the CANCEL.
• You can change the camera angle directly by pressing the
number keys corresponding to its angle number instead of
/
repeatedly until the desired angle is
2
using the
/
buttons.
Title Selection
Two or more titles are recorded on some discs. If the title menu
is recorded on the disc, you can select the desired title.
Press TITLE during playback.
Title menu appears on the screen.
• Press TITLE again to resume playback at the scene
when you pressed TITLE.
1
Press
/
or
/
to select the desired title.
2
3
Press OK or
The playback of the selected title will start.
.
DVD Menu
Some DVDs allow you to select the disc contents using the
menu.
When you play back these DVDs, you can select the subtitle
language and sound-track language,etc. using the DVD menu.
Press DVD MENU during playback.
The DVD menu appears on the screen.
1
NOTE:
• Press DVD MENU again to resume playback at
the scene when you pressed DVD MENU.
Depending on the DVD, you may not
be able to change the angles even if
multi-angles are recorded on the disc,
or you may be unable to select the title,
and a “title menu” may simply be called
a “menu” or “title” in the instructions
supplied with the disc.
Press
/
or
/
to select the desired item.
2
3
Press OK.
The menu continues to another screen. Repeat steps 2 and 3 to
set the item completely.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Parental control
Somediscsarespecifiednotsuitable
for children. Such discs can be
prevented from play back with the
unit.
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press DVD to select the DVD mode. (The DVD indicator will light)
Parental control setting
PressSET UP MENU in the stop
1
mode.
Picture
Press or to select “Opera-
TV Shape 4:3LB
Video Out Select
tion”.
: Select
: Enter
Press
or
to select
2
3
“Parental Lock”, then press OK.
Operation
Pause/Still
Auto Off
Parental Lock
Title Stop
PBC
Off On
Off
On
: Select
: Enter
Press
or
to select Off or On.
Off: The parental lock feature
does not function.
Operation
Pause/Still
Parental Lock
Title Stop
PBC
Auto Off
Off On
Off
After pressing OK (Enter),
follow step 4 and 6 below.
On: To activate the parental lock
feature or change the
setting, press OK (Enter)
and follow steps 4-6 below.
On
: Select
: Enter
Press number keys to input a
4-digits security code then
press OK.
• If you input a wrong number,
press CANCEL.
4
5
Operation
Pause/Still
Parental Lock
Title Stop
Auto Off
Off On
Off
On
Security Code ----
PBC
• To return to the before step,
press RETURN.
: Select
: Enter
NOTES:
Enter the code of a country/area
whose standards were used to
rate the DVD disc. (See the list
on the page 51)
• If each setup (page 50~59) has been
completed, the unit can always be
worked under the same conditions
(especially with DVD discs).
Each setup will be retained in the
memory if you turn the power off.
• Depending on the discs, the unit can-
not limit playback.
Operation
Pause/Still
Parental Lock
Title Stop
Auto Off
Off On
Off Area Code
D E
PBC
On
Example: Set to DE (GERMANY).
: Select
: Enter
Press
press
or
to select “D” then
to move to the right
• Some discs may not be encoded with
specific rating level information though
its disc jacket says "adult". For those
discs, the age restriction will not work.
• Do not forget the security code. If you
forget the security code, delete it. (See
step 7 on next page)
character.Then select “E” same
as above. Then press OK (En-
ter).
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Parental control
Country/Area
AUSTRALIA
BELGIUM
CANADA
Code
AU
BE
CA
CN
HK
DK
FI
Country/Area
NETHERLANDS
NORWAY
PHILIPPINES
RUSSIAN FEDERATION
SINGAPORE
SPAIN
Code
NL
NO
PH
RU
SG
ES
CHINA
CHINA HONG KONG
DENMARK
FINLAND
SWEDEN
SE
FRANCE
FR
DE
ID
IT
JP
SWITZERLAND
TAIWAN
THAILAND
UNITED KINGDOM
UNITED STATES
CH
TW
TH
GB
US
GERMANY
INDONESIA
ITALY
JAPAN
MALAYSIA
MY
Press
/
to select the paren-
6
tal lock level, then press OK (En-
ter).
Operation
Pause/Still
Parental Lock
Title Stop
Auto Off
Off On
Off Area Code
D E
PBC
On Level
7
: Select
: Enter
You cannot play DVD discs rated higher than the level you selected
unless you cancel the parental lock function.
For example, when you select level 7, discs rated higher than level
7 are locked out and cannot be played.
• Level 1: DVD software for adults cannot be played back.
• Level 8: All DVD software can be played back.
• Select from the level 1 to level 8.The limitation will be more severe
as the level number is lower.
To make the SETUP screen disappear, press SET UP MENU.
7
To change the parental lock level
Follow steps 1- 6.
To change your 4-digit security code
1) After selecting “On” or “Off” at step 3 press 3 four times, then
press OK (Enter).
The 4-digit security code is deleted.
2) Press number keys to create a new 4-digit security code at step4.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menu language
You can select the language of the
disc menu messages of DVDs.
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press DVD to select the DVD mode. (The DVD indicator will light)
Press SET UP MENU in the stop
mode.
1
Picture
TV Shape 4:3LB
Press
or
to select “Lan-
Video Out Select Video
guage”.
: Select
: Enter
Press
Menu Language”.
or
to select “Disc
2
3
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
Subtitle Language
ENG
ENG
: Select
: Enter
Press OK (ENTER).
Press
desiredlanguage,thenpressOK
or
to select your
Language
On-Screen Language ENG English
Disc Menu Language ENG French
(ENTER).
Audio Language
ENG German
ENG Others
Subtitle Language
Code D E
: Select
: Enter
English, French, German
The selected language is the first-priority Menu language.
Others: Other languages can be selected (See the Table of
languages on page 61).
Example:
Set to DE (GERMANY).
Press
or
to select “D” then press
to move to
the right character. Then select “E” same as above.
Then press OK (ENTER).
To make the SETUP screen disappear, press SET UP MENU.
4
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting audio soundtrack language
Thesameaudiosoundtracklanguage
Preparation:
can always be selected by your unit
even if you replace the disc or turn
the power off.
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press DVD to select the DVD mode. (The DVD indicator will light)
Press SET UP MENU in the stop
mode.
1
Picture
TV Shape 4:3LB
Press
or
to select
Video Out Select Video
“Language”.
: Select
: Enter
Press
Language”.
or
to select “Audio
2
3
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
Subtitle Language
ENG
ENG
: Select
: Enter
Press OK (Enter).
Press or to select your
desired Audio Language, then
C
Language
On-Screen Language ENG English
Disc Menu Language ENG French
press OK (Enter).
Audio Language
ENG German
ENG Others
Subtitle Language
Code D E
: Select
: Enter
English, French, German
The language you have selected will play if it is recorded on
the disc.
Others: If you want to select another language, enter the lan-
guage code (See theTable of languages on page 61).
Example:
Set to DE (GERMANY).
Press
or
to select “D” then press
to move to
the right character. Then select “E” same as above.
Then press OK (Enter).
To make the SETUP screen disappear, press SET UP MENU.
4
NOTES:
• If the selected language is not re-
corded on the disc, the original lan-
guage will be heard.
• Some DVD discs may be played in a
different language than you selected.
A prior language may be programmed
on the disc.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting subtitle language
The same subtitle language can
always be selected even if you replace
the disc or turn the power off.
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press DVD to select the DVD mode. (The DVD indicator will light)
Press SET UP MENU in the stop
mode.
1
Picture
TV Shape 4:3LB
Press
or
to select
Video Out Select Video
“Language”.
: Select
: Enter
Press
Language”.
or
to select “Subtitle
2
3
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
Subtitle Language
ENG
ENG
: Select
: Enter
Press OK (Enter).
Press or to select your
desiredlanguage,thenpressOK
Language
English
On-Screen Language ENG French
Disc Menu Language ENG German
Audio Language
Subtitle Language
ENG No Subtitle
(Enter).
ENG
Others
Code D E
: Select
: Enter
English, French, German
The subtitle is displayed with the selected language if it is
recorded on the disc.
No Subtitle:
Subtitles do not appear.
Others: If you want to select another language, enter the
language code (See the Table of languages on
page 61).
Example: Set to DE (GERMANY).
Press
or
to select “D” then press
to move to
the right character. Then select “E” same as above.
Then press OK (Enter).
NOTES:
To make the SETUP screen disappear, press SET UP MENU.
4
• If the selected language is not recorded
on the disc, the first-priority language is
selected.
• Some DVD discs may be set to display
Subtitles in a different language than
you selected. A prior subtitle language
may be programmed on the disc.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the aspect ratio of TV screen / Setting on Screen display
You can select the aspect ratio for
your TV.
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press DVD to select the DVD mode. (The DVD indicator will light)
Setting the aspect ratio of TV screen
Press SET UP MENU in the stop
mode.
1
Picture
TV Shape 4:3LB
Press
or to select
Video Out Select Video
“Picture”, then press
to select “TV shape”.
or
: Select
: Enter
Press OK (Enter).
2 Press
or
to select your
Picture
TV Shape 4:3LB
4:3 Letterbox
4:3 Normal
desired screen type.
Video Out Select Video
16:9 Widescreen
: Select
: Enter
You have the following screen sizes to choose from:
4:3 Letterbox:
Select when a standard 4:3 TV is connected.
Displays theatrical images with masking bars above and below
the picture.
4:3 Normal:
Select when a standard 4:3 TV is connected.
Displays pictures cropped to fill your TV screen. Either or both
sides of the picture are cut off.
16:9 Widescreen:
Select this mode when connecting to a wide-screen TV.
A wide screen picture is displayed full size.
To make the SETUP screen disappear, press SET UP MENU.
3
Setting on Screen display
Press SET UP MENU in the stop
mode.
NOTES:
1
• The displayable picture size is preset on
the DVD video disc. Therefore, the
playback picture of some DVD video
discs may not conform to the picture size
you select.
• When you play DVD video discs re-
corded in the 4:3 picture size only, the
playback picture always appears in the
4:3 picture size regardless of the TV
shape setting.
Display
On-Screen Displays On
Press
or
or
to select “Display”
to select “On-
Background
Screen Saver
Picture
On
Press
2 Screen Displays”.
: Select
: Enter
Press OK (Enter).
3
Press
or
to select “On” or
Display
On-Screen Displays Off
“Off”.
Off
Background
Screen Saver
Picture On
On
• If you select “16:9 widescreen” and you
own a 4:3 TV set, the DVD playback
picture will be horizontally distorted dur-
ing playback. Images will appear to be
horizontally compressed. Always be
sure that yourTV shape conforms to the
actual TV in use.
On: Operational modes (e.g.
“ ”, “ ”) appear when you
press the buttons (factory
setting).
: Select
: Enter
Off: Operational modes (e.g. “ ”, “ ”) do not appear when
you press any buttons.
To make the SETUP screen disappear, press SET UP MENU. 55
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Audio
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press DVD to select the DVD mode. (The DVD indicator will light)
Audio Out Select
Select the output sound format corresponding to your system connection.
For details of sound recording systems, see on page 59.
Press SET UP MENU in the stop mode.
1 Press
or
to select “Audio”.
Audio
Audio Out Select
Dynamic Range Control On
Karaoke Vocal
Bitstream
Bitstream
Analog 2ch
PCM
On
Press
or
to select “Audio Out
2 Select”, then press OK (Enter). Press
or
to select your desired output
: Select
: Enter
sound.
Bitstream:
Select when connected to an amplifier equipped with a Dolby
Digital, DTS, MPEG1 or MPEG2 decoder. The DVD/VCR outputs
digital audio information in the bitstream format when you play a
DVD video disc recorded on the Dolby Digital, DTS, MPEG1 or
MPEG2 recording system.
Analog 2ch: SelectwhenconnectedtoaTV, DolbyProLogicorstereosystem
via the analog audio jacks.
PCM:
Select when connected to a 2 channel digital stereo amplifier.
The DVD/VCR outputs sounds in the PCM 2ch format when you
play a DVD video disc recorded on the Dolby Digital. MPEG1 or
MPEG2 recording system.
3 To make the SETUP screen disappear, press SET UP MENU.
Dynamic Range Control
Turn on or off a function that makes faint sounds easier to hear
even if you lower the volume during late hours playback.
Press SET UP MENU in the stop
1 mode.
Audio
Audio Out Select
Dynamic Range Control On
Karaoke Vocal
Bitstream
Off
On
Press
or
or
to select “Audio”.
to select “Dynamic
Off
Press
2 Range Control”, then press OK (Enter).
: Select
: Enter
Press
or
to select “On” or “Off”.
Off: Fulldynamicrangeismaintained.
On: Dynamic range is reduced.
To make the SETUP screen disappear,
3 press SET UP MENU.
NOTES:
• The Dynamic Range Control function
works only during playback of Dolby
Digital recorded discs.
Karaoke Vocal
Turn on or off the vocal output during DVD KARAOKE disc
playback.
• The level of Dynamic Range Control
may differ depending on the DVD video
disc.
• The vocal output feature is used during
playback of Dolby Digital (multi-channel)
recorded DVD KARAOKE discs. This
feature allows you to turn off vocal audio
tracks, or restore them for background
accompaniment.
PressSETUPMENU inthestopmode.
1
Audio
Audio Out Select
Dynamic Range Control On
Karaoke Vocal
Press
or
to select “Audio”.
Bitstream
Off
On
Off
Press
or
to select “Karaoke
2
Vocal”, then press OK (Enter).
Press or to select “On” or “Off”.
: Select
: Enter
Off: The primary vocal is not output.
On: Theprimaryvocalisoutputwhen
it is recorded on the disc.
• When playing KARAOKE, connect the
appropriate audio equipment such as an
amplifier to the DVD player.
To make the SETUP screen disappear, press SET UP MENU.
3
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Operation
Preparation:
PBC
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to
VCR/DVD. Then press DVD to select the DVD mode.
(The DVD indicator will light)
Press SET UP
1
MENU in the stop
Picture
mode.
TV Shape 4:3LB
Video Out Select Video
Press
or to
Pause/Still
Select the resolution of still pictures.
select “Operation”.
: Select
: Enter
PressSETUPMENU
in the stop mode.
1
Picture
TV Shape 4:3LB
Video Out Select Video
Press
(Enter).
or
or
to select “PBC”, then press OK
to select “On” or “Off”, then press
Press or
to
2
select “Operation”.
Press
OK (Enter).
: Select
: Enter
Press
select “Pause/Still”,
then press OK
or
to
2
Operation
Pause/Still
Parental Lock
Title Stop
PBC
Auto
Off
Off
Off
On
Operation
Pause/Still
Parental Lock
Title Stop
PBC
Auto
Off
Off
Auto
Frame
On
(Enter). Press
or
On
to select “Auto”
or “Frame”, then
press OK (Enter).
: Select
: Enter
: Select
: Enter
Off: When playing a VIDEO CD without using
the menu.
On: To use the menu when playing a PBC-
featured VIDEO CD.
Auto: For normal use. Still and fast motion images
can be paused.
Frame:The resolution of still pictures is improved,
so that you can make a motionless picture
clearer when you pause it.
To make the SET UP screen disappear, press SET
UP MENU.
3
To make the SETUP screen disappear, press SET UP
MENU.
3
Title Stop
Turn on or off a feature that automatically stops
playback after a title has been viewed.
PressSETUPMENU
in the stop mode.
1
Picture
TV Shape 4:3LB
Video Out Select Video
Press
or
to se-
lect “Operation”.
: Select
: Enter
Press or
to
2 select “Title Stop”,
Operation
then press OK
Pause/Still
Parental Lock
Title Stop
PBC
Auto
Off
Off
Off
On
(Enter).
Press or
On
to
select “On” or “Off”,
then press OK
(Enter).
: Select
: Enter
Off: The DVD/VCR continues after playback of
a title is completed.
On: The DVD/VCR stops after playback of a title
is completed.
To make the SETUP screen disappear,
3 press SET UP MENU.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the sound enhancement (E.A.M.)/Setting Background/
Setting Screen Saver
Setting Background
Preparation:
Select the background color or background picture.
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to
VCR/DVD. Then press DVD to select the DVD mode.
(The DVD indicator will light)
PressSETUPMENU
in the stop mode.
1
Picture
TV Shape 4:3LB
Press
or
to se-
Video Out Select Video
Selecting the sound enhancement (E.A.M.*)
You can easily switch a preferred audio enhancement.
lect “Display”.
*E.A.M.: Enhanced Audio Mode
: Select
: Enter
Press OSD twice.
2
3
-0:21:28
Press
select “Back-
ground”, then press
OK (Enter). Press
or
to
1
2
Display
On-Screen Display On
Background Picture
Blue
Gray
Screen Saver
On
Picture
Jacket
or
to select
your desired
background, then
press OK (Enter).
Then press B/A to
select the E.A.M.
icon, then press OK
(Enter).
The sound enhance-
ment menu appears.
: Select
: Enter
Blue:
Gray:
Blue background.
Gray background.
Picture: Use the picture which appears when you
turn on the DVD/VCR as a background.
Jacket: Use the jacket picture included on some
discs as a background. If it is not included,
a gray background will be substituted.
Select the sound enhancement by pressing / .
Eachtimeyoupressthebutton,thesoundenhance-
ment changes.
2
To make the SETUP screen disappear, press SET
3 UP MENU.
Normal:
Normal sound.
Setting Screen Saver (DVD only)
3D:
To turn the screen saver on or off.
To obtain expansive virtual surround sound
effects from just two speakers.
PressSETUPMENU
1
Dialogue:
in the stop mode.
Picture
TV Shape 4:3LB
Video Out Select Video
To control critical center channel information
to make dialogue more intelligible (only
when playing a DVD video disc recorded on
the Dolby Digital recording system).
Press
or to
select “Display”.
•
To use this enhancement on sounds output
from the BITSTREAM/PCM jack, be sure to
set “Audio Out Select” to “PCM.” (see page 56).
: Select
: Enter
Press
select “Screen
Saver”, then press
OK (Enter).
Press or
select “On” or “Off”,
then press OK
(Enter).
or
to
2
To exit the audio enhancement selection Press
CANCEL.
Display
On-Screen Display On
Background Picture
Off
On
Screen Saver
On
Notes:
to
• Actual effects to sounds may vary depending on the speaker
system. Make selection according to your preference.
• Actual effects to sounds may vary depending on the disc.
• When the DVD/VCR is connected to an amplifier equipped
with Dolby Pro Logic Surround, select “Normal”.
Otherwise, Dolby Pro Logic Surround may function
differently than usual.
: Select
: Enter
Off: The screen saver is disengaged.
On: The screen saver operates in 10
minutes after you press
4
.
• Selecting “Dialogue” disables “Dynamic Range Control”
function (see page 56).
• During MP3 playback, the sound enhancement is not
effective.
To make the SETUP screen disappear, press SET
3 UP MENU.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting initial setup/output sound conversion table
You can install the initial system
Preparation:
setting.
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided toVCR/DVD.Then
press DVD to select the DVD mode. (The DVD indicator will light)
Setting initial setup
Press SET UP MENU in the stop
mode.
1
Picture
TV Shape 4:3LB
Video Out Select Video
Press or
to select “Initial
Setup”.
: Select
: Enter
Press OK, then press
or
2
to select “On-Screen Language”,
“TV Shape” or “Audio Out
Select”.
Initial Setup
On-Screen Language ENG
English
Deutsch
TV Shape
4:3LB
Audio Out Select
Bitstream
: Select
: Enter
On-Screen Language:
TV Shape:
Audio Out Select:
See on page 41.
See on page 55.
See on page 56.
To make the SETUP screen disappear, press SET UP MENU.
3
Output sound conversion table (sampling frequency/quantization bit)
You can select the output sound format corresponding to your system connection (see page 56).
Bitstream
Analog 2ch
PCM
Discs
Recording system
Dolby Digital
DIGITAL AUDIO ANALOG AUDIO DIGITAL AUDIO ANALOG AUDIO DIGITAL AUDIO ANALOG AUDIO
OUT jack
OUT jack
OUT jack
OUT jack
OUT jack
OUT jack
Bitstream
48 kHz/20 bit
Bitstream
48 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit
48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit
48 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit
48 kHz/24 bit 48 kHz/16 bit 48 kHz/24 bit 48 kHz/16 bit 48 kHz/24 bit 48 kHz/16 bit 48 kHz/24 bit
DVD video
discs
Linear PCM
96 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit
96 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit
96 kHz/24 bit 48 kHz/16 bit 48 kHz/24 bit
—
—
96 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit
96 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit
96 kHz/24 bit 48 kHz/16 bit 48 kHz/24 bit
—
Bitstream
Bitstream
DTS
Bitstream
Bitstream
—
—
—
—
MPEG1, MPEG2
Linear PCM 44.1 kHz/16 bit
DTS
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit
CDs
Bitstream
(Noise)
Bitstream
(Noise)
Bitstream
(Noise)
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Status display of Disc
You can view information on the operation status and access and settings.
With each press of OSD, the status of the disc will appear on the screen and change as follows.
1
Symbol mark of the feature
Audio/
mark is only for
Video CD.
DVD
you selected is displayed.
Video CD
ZOOM
T
2
C
3
0:08:16
T
2
C
3
-0:21:28
T
1
00:30
T
1
-03:38
EAM
EAM
EAM
EAM
2CH
ZOOM
2CH
ZOOM
PCM
PCM
X
1
X
1
C
C
OFF
OFF
BIT
T
2
C
3
0:08:16
RATE
9.2Mbps
T
2
C
3
T
1
01:14
T
1
EAM
EAM
EAM
EAM
----- CD TEXT -----
Disc Title:
No Text
2CH
ZOOM
2CH
ZOOM
PCM
PCM
X
X
Track Title:
No Text
1
1
C
C
(Audio CD only)
Press
or
to select the desired symbol mark, then press OK (Enter).
2
: Title number (Track number)
: Chapter number
T
C
Press
/
or number keys to locate a title or
Press
/
or number keys to locate a Chapter,
track, then press OK (Enter).
then press OK (Enter).
: Elapsed (remaining) time of the current title
Audio setting
See page 48.
Press number keys to locate a desired Location,
then press OK (Enter).
: Angle setting
See page 49.
: Subtitle setting
See page 48.
: E.A.M. (Enhanced Audio Mode)
See page 58.
ZOOM
: To zoom a picture
See page 44.
: Audio Out Select setting
BST: Bitstream 2CH:Analog 2ch PCM:PCM
See page 56.
: To stop playback
See page 42.
: Playback starts from the beginning of the
current chapter or track.
See page 43.
: Fast reverse playback
See Page 43.
: To start playback
See page 42.
: Fast forward playback
See page 43.
: To locate succeeding chapters or tracks.
See page 43.
: To begin slow motion playback
See page 43.
: To pause playback
See page 43.
: To turn off the display
Data transfer rate (Mbit/s)
Amount of picture, sound and subtitle data in the DVD
video disc transferred per second.
The larger the value is, the more data processed, but
this does not necessarily insure better picture quality.
CD TEXT
Displays CD text data if included on the audio
CDs. (Some letters may not be displayed
properly depending on the disc.)
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of languages
Enter the appropriate code for the initial settings"Menu", "Audio" and/or "Subtitle" (see pages 52~54).
Abbreviation Language Abbreviation Language Abbreviation Language
– – –
No alternate
language
Chinese
Dutch
English
French
German
ltalian
Japanese
Korean
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
CHI (ZH)
DUT (NL)
ENG (EN)
FRE (FR)
GER (DE)
ITA (IT)
JPN (JA)
KOR (KO)
MAY (MS)
SPA (ES)
AA
Sango
Malay
Spanish
Afar
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
IW
JI
SK
SL
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Belorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Yiddish
JW
KA
KK
KL
KM
KN
KS
KU
KY
LA
LN
LO
LT
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laotian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tongan
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
LV
MG
MI
MK
ML
MN
MO
MR
MT
MY
NA
NE
NO
OC
OM
OR
PA
PL
PS
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Irish
Scottish Gaelic
Galician
Xhosa
Yoruba
Zulu
GL
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and troubleshooting
Use the following check list for troubleshooting when you have problems with your unit. Consult your local
dealer or service outlet if problems persist.
Be sure all connections are properly made when using with other units.
SYMPTOMS
DVD/VCR
POSSIBLE SOLUTIONS
PAGE
•Make sure the power cord is plugged in.
•Try another AC outlet.
•Power is off, check fuse or circuit breaker.
•Unplug unit, then plug it back in.
–
–
–
DVD/VCR does not operate.
–
•Select the DVD or VCR mode before operating.
14,41
•
Antenna connection is not correct or antenna cable is disconnected.
10
13
• The video channel is not in the correct position or the TV is not
set to the video channel.
• Check the unit is connected correctly.
• The video input selector of the TV is not set to VIDEO. Set to
VIDEO (or equivalent).
10~12
No picture.
No sound.
–
• Channel is set to the external mode.
–
• Check the unit is connected correctly.
• Check the input selector of the amplifier is set properly.
• The unit is in the Special playback mode.
10~12
–
24,43
• Aim at the remote control at the remote sensor.
• Operate within Approx. 5 Meters or reduce the light in the room.
• Clear the path of the beam.
• The batteries are weak. Replace the batteries.
• Check the batteries are inserted correctly.
• Check the frequency code is set correctly.
The remote control does not
function.
9
8
The DVD-keys on the RCU of the
other JVC RECEIVER/TV is not
effective.
• This is not a defect. Since this unit is combined type of DVD and
VCR, the remote code of DVD is individual.
VCR
•The erase prevention tab of the video cassette is broken off.
•The unit is in the external input mode.
TV recording does not work.
22,28
• The time is not set correctly.
• The recording start/end time is not set correctly.
• The • has not been pressed ( is not lit).
15
33
34
Timer recording does not work.
• Tracking adjustment beyond range of automatic tracking circuit.
Try Manual tracking adjustment.
• Video heads are dirty.
24
Noise bars on screen.
63
–
• The tape is worn or damaged.
DVD
Display is not shown in your
language.
•Select proper language in the menu options.
41
• No disc is inserted.
• The disc may be dirty. Clean up the disc.
• The unit cannot play DVD-ROMs, etc.
42
40
40
Playback doesn’t start.
Stopping playback, slow-motion
play, repeat play, or memory play, • Some discs may not do some of the functions.
–
etc. cannot be performed.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and troubleshooting / Video head cleaning
SYMPTOMS
No 4:3 (16:9) picture
No on-screen display
No surround sound
POSSIBLE SOLUTIONS
• The setup does not match your TV.
PAGE
55
• Select Display On.
55
• The setup does not match your stereo system.
12
The unit or remote operation key
is not functioning.
• Turn off the unit and unplug the AC power cord for several
minutes, then replug it.
14
50
Playback does not start when the
title is selected.
• Check the Parental control setting.
Audio soundtrack and/or subtitle
language is not changed when
you play back a DVD.
53,54
• Multilingual language is not recorded on the DVD disc.
• Some discs have no subtitles.
• Subtitles are cleared. Press SUB TITLE.
54
48
No subtitle
Angle cannot be changed.
appears on the screen.
• Multi-angles are not recorded on the DVD disc.
• The function is prohibited with the unit or the disc.
49
–
Video head cleaning
Video head clogging
The video heads are the means by which the DVD/VCR reads
the picture from the tape during playback.In the unlikely event
that the heads become dirty enough to be clogged, no pic-
ture will be played back. This can easily be determined if,
during playback of a known good tape, there is good sound,
but no picture (picture is extremely snowy).If this is the case,
have the DVD/VCR checked by qualified service personnel.
Good Picture
Snowy Picture
NOTES: DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THE
•
REAR COVER.
Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.
To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.
•
•
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
GENERAL
Power supply:
AC 230V 50Hz
Power consumption:
Operation: 22W
Stand by: 5W
4.5 kg
Weight:
Dimensions:
Width : 430 mm
Height: 99 mm
Depth : 310.5 mm
Input Level:
SCART-socket:
VIDEO: 1 Vp-p, 75 Ω
AUDIO: 500 mV, 50 k Ω
Audio IN jack: 500 mV, 50 k Ω
Output Level:
SCART-socket:
VIDEO: 1 Vp-p, 75 Ω
AUDIO: 500 mV, 1 k Ω
Audio OUT jack: 500 mV, 1 k Ω
Hi-Fi Frequency Response: 20Hz to 20,000Hz
Hi-Fi Dynamic Range:
More than 75dB
VCR section
Video Head:
4 Rotary Heads
Audio Track:
Channel covevage:
RF Channel Output:
Hi-Fi Sound - 2 Tracks / MONO Sound - 1 Track
2-12, X, Y, Z, S1-S41, 21-69
UHF channel 36 (23 to 69)
F.FWD/REW Time at 25˚C: Approx. 1minute and 48 seconds (with E-180 Cassette Tape)
DVD section
Signal system:
Applicable disc:
Audio characteristics:
Frequency response:
S/N Ratio:
PAL
DVD (12cm, 8cm), CD (12cm, 8cm)
DVD: 4Hz - 22KHz
CD: 4Hz - 20KHz
90dB
Harmonic distortion:
Wow and flutter:
Dynamic range:
Output:
1%
Below Measurable Level
90dB
Audio : (RCA) 500 mV, 1Kohm
Digital Audio : 0.5Vp-p/75 ohm
CD : Wavelength: 775 - 805 nm
Maximum output power: 0.5 mW
DVD : Wavelength: 640 - 660 nm
Maximum output power: 1.0 mW
Pickup:
ACCESSORIES:
Remote control x 1
75 ohm Coaxial Cable x 1
Battery (UM-3) x 2
2A73501A
02/04
U
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Infinity Portable Speaker PS212 User Manual
Ingersoll Rand Marine Sanitation System 650709 C User Manual
Intermec PDAs Smartphones CN2G User Manual
Jenn Air Cooktop JED8130ADB User Manual
JVC Computer Monitor TM A210G User Manual
JVC Digital Camera GR DV400 User Manual
JVC DVD Player XV S60BK User Manual
Kaidan Camcorder Accessories KiWi+ User Manual
King Canada Saw KC 1401HD User Manual
Kompernass Fondue Maker KH 1090 User Manual