U
E
DVD RECORDER
DVD-RECORDER
ENREGISTREUR DE DVD
GRABADORA DE DVD
MASTERIZZATORE DVD
DVD RECORDER
INSTRUCTIONS
INSTRUCTIONS
BD-X200U
BD-X200E
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
INSTRUCCIONES
ISTRUZIONI
BUSY
BUSY
OPERATE
OPEN/CLOSE
OPERATE
OPEN/CLOSE
OPTION DV Y/C LINE
SET UP
OPTION DV Y/C LINE
DVD RECORDER BD-X200
TITLE
DVD RECORDER BD-X200
TITLE
AUDIO
AUDIO
SET UP
CHAPTER
CHAPTER
CH1
CH2
CH1
CH2
DOLBY DIGITAL
LPCMMPEG
DOLBY DIGITAL
LPCMMPEG
SET
SET
TOP
PHONES
REV
STOP
PLAY
FWD
PAUSE
REC
TOP
PHONES
REV
STOP
PLAY
FWD
PAUSE
REC
MENU
MENU
MENU
MENU
Thank you for purchasing this JVC product. Before operating
this unit, please read the instructions carefully to ensue the
best possible performance.
For Customer Use :
Enter below the Serial No. which is located on the bottom
of the unit.
Retain this information for future reference.
Thank you for purchasing this JVC product. Before operating
this unit, please read the instructions carefully to ensue the
best possible performance.
Model No. BD-X200U
Serial No.
LLT0060-001A-C
LLT0061-001A-C
Download from Www.Somanuals.com. All Manuals Search And Download.
U
E
SAFETY PRECAUTIONS
Safety Precautions
POWER SYSTEM
Warning Notice
Connection to the mains supply
This unit operates on voltage of 220 V to 240 V AC, 50
Hz/60 Hz.
FOR YOUR SAFETY (Australia)
CAUTION
ATTENTION
1. Insert this plug only into effectively earthed three-
pin power outlet.
2. If any doubt exists regarding the earthing, consult a
qualified electrician.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE D’ELECTROCUTION
NE PAS OUVRIR
WARNING:
ATTENTION: POUR EVITER TOUT RISQUE D’ELECTROCUTION
NE PAS OUVRIR LE BOITER.
ACCUNE PIECE INTERIEURE N’EST.
A REGLER PAR L’UTILISATEUR.
SE REFERER A UN AGENT QUALIFIE EN CAS DE PROBLEME.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
3. Extension cord, if used, must be three-core correctly
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
wired.
The lightning flash wish arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
Le symbole de l’éclair à l’intérieur d’un triangle équilatéral est
destiné alerter l’utilisateur sur la présence d’une “tension
dangereuse” non isolée dans le boîtier du produit. Cette tension
est suffisante pour provoquer l’électrocution de personnes.
IMPORTANT (In the United Kingdom)
Mains Supply (AC 230 V `)
WARNING – THIS APPARATUS
MUST BE EARTHED
CAUTION
à
To prevent electric shock, do not open the cabinet. No
user serviceable parts inside. Refer servicing to
qualified service personnel.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
Le point d’exclamation à l’intérieur d’un triangle équilatéral est
destiné
à
alerter l’utilisateur sur la présence d’opérations
The wires in this mains lead are coloured in accordance
with the following code;
GREEN-and-YELLOW : EARTH
d’entretien importantes au sujet desquelles des renseignements
se trouvent dans le manuel d’instructions.
WARNING
*Ces symboles ne sont utilisés qu’aux Etats-Unis.
This is a Class A product. In a domestic environment
this product may cause radio interference in which case
the user may be required to take adequate measures.
BLUE
BROWN
: NEUTRAL
: LIVE
WARNING:
AVERTISSEMENT:
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug, proceed
as follows.
The wire which is coloured GREEN-AND-YELLOW
must be connected to the terminal in the plug which is
marked with the letter E or by the safety earth symbol
or coloured GREEN or GREEN-AND-YELLOW.The
wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or which is
coloured BLACK. The wire which is coloured BROWN
must be connected to the terminal which is marked
with the letter L or coloured RED.
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
POUR EVITER LES RISQUES D’INCENDIE OU
D’ELECTRO-CUTION, NE PAS EXPOSER
L’APPAREIL A L’HUMIDITE OU A LA PLUIE.
Note:
This unit should be used with 120 V AC only.
The rating plate and the safety caution are on the
bottom of the unit.
Ce magnétoscope ne doit être utilisé que sur du
courant alternatif en 120V.
CAUTION:
To prevent electric shocks and fire hazards, DO NOT
use any other power source.
ATTENTION:
Afin d’éviter tout resque d’incendie ou
d’électrocution, ne pas utiliser d’autres sources
d’alimentation électrique.
The OPERATE button does not completely shut off
mains power from the unit, but switches operating
current on and off.
Note:
The rating plate (serial number plate) is on the bottom of the unit.
WARNING
REMARQUE:
La plaque d’identification (numéro de série) se trouve sur le
panneau arrière de l’appareil.
It should be noted that it may be unlawful to re-record
pre-recorded tapes, records, or discs without the
consent of the owner of copyright in the sound or video
recording, broadcast, or cable programme and in any
literary, dramatic, musical or artistic work embodied
therein.
INFORMATION
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.
WARNING:
The battery used in the BD-X200U must be replaced by a JVC
authorized service dealer only.
Caution for AC Mains Lead
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This product is equipped with 2 types of AC cable. One is for continental Europe, etc. and the other one is only for
U.K.
CAUTION
Appropriate mains cable must be used in each local area, since the other type of mains cable is not suitable.
CHANGES OR MODIFICATIONS NOT APPROVED BY JVC
COULD VOID USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
FOR CONTINENTAL EUROPE, ETC.
FOR U.K. ONLY
Not to be used in the U.K.
If the plug supplied is not suitable for your socket outlet,
it should be cut off and appropriate one fitted.
This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les
exigences du Reglement sur le matériel brouilleur du Canada.
II
II
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings & Controls for Recording
Thank you for purchasing
this JVC BD-X200 DVD Recorder.
Trademarks & Copyrights
DVD Recording.................................................................................................................................................................. 29
Preparing a Disc for Recording ......................................................................................................................................... 30
Pre-Recording Settings ..................................................................................................................................................... 31
Selecting & Confirming Input Signals ................................................................................................................................ 32
Setting the Encoding Format for Audio & Video ................................................................................................................ 33
Adjusting of Audio Recording Levels ................................................................................................................................. 35
Checking the Video Input .................................................................................................................................................. 36
Selecting Styles for Title & Chapter Menu ......................................................................................................................... 37
●
,
Dolby and the Double “D” symbols are
trademarks of Dolby Laboratories.
● The copying, broadcasting, screening, or rental of
copyrighted material without the authorization of the
copyright holder is prohibited by law.
Main Features
● Recording of DVD-R and DVD-RW (video mode only).
● Composite video,YC separate, and DV signals are supported
as video inputs; furthermore, analog or DV signals are
supported as audio inputs.
Copyright Protection Technology
Recording
This DVD recorder utilizes copyright protection technology
and is protected by US patents and intellectual property as
owned by Macrovision and other copyright holders. The
permission of Macrovision is required in order to use this
copyright protection technology, and except in situations
where special permission has been granted by that
company, said technology is restricted to domestic usage
and for certain other viewing purposes. The disassembly
and/or modification of this DVD recorder is also prohibited.
Recording Sequence ......................................................................................................................................................... 38
Recording with the Front Panel ......................................................................................................................................... 39
Inserting Chapter Marks Manually or Automatically .................................................................................................... 40
Using a Keyboard & Mouse to Control Recording ............................................................................................................. 41
Finalizing (for playback on this and other DVD players) .................................................................................................... 42
● A keyboard and mouse can be used as an alternative to front
panel buttons.
● When the BD-X200 is connected to an RS-422A compatible
VCR, RS-422 control can be used to carry out synchronous
recording of the VCR’s video and audio to a DVD.
Title & Chapter Menu Settings
● Synchronous recording of video and audio from a DV camera
or video player to a DVD can also be carried out.
BD-X200 Title & Chapter Menus ....................................................................................................................................... 43
Selecting and Changing Styles for Title & Chapter Menus ................................................................................................ 44
Easymenu: Freeware for Editing Menu Templates ............................................................................................................ 46
Changing Chapter Menus (THUMBNAIL EDIT screen) .................................................................................................... 47
Changing & Naming Thumbnails for Chapter Menus ........................................................................................................ 48
Changing & Checking Chapter Menu Styles ..................................................................................................................... 50
Ending the Editing of Chapter Menus................................................................................................................................ 52
Changing & Checking Title Menu Styles & Names............................................................................................................ 53
● The DV IN/OUT terminal can be used to record audio and
video from a non-linear editor to a DVD.
Copyrights
● The recording, dubbing, or playing of software containing
a copyright protection signal is not possible on this DVD
recorder.
● The usage of audio or video discs created using this DVD
recorder either for financial gain or in broadcasting for
widespread viewing may result in the legally-enforceable
rights of the copyright holder being infringed.
● Unless the permission of the copyright holder has been
obtained, audio or video discs created using this DVD
recorder are to be used for personal enjoyment only.
● The title and chapter menus can be created either
automatically or manually.
● This DVD recorder features a LAN terminal. Accordingly, two
of these recorders can be connected using LAN (CAT 5) cables
to perform master-to-receiver dubbing.
Playback
Playing Discs ..................................................................................................................................................................... 57
Fast & Slow Playback ........................................................................................................................................................ 58
Playing the Previous or Next Chapter................................................................................................................................ 58
Synchronous Recording
Recording Playback Signals From a VCR with RS-422A .................................................................................................. 59
Recording Playback Signals From a DV Camera or VCR ................................................................................................. 63
Recording Video & Audio From a Non-Linear Editor ......................................................................................................... 64
In, Out & Chapter Points from External Edit Lists.............................................................................................................. 68
Recording Operations Using a DV Camera Trigger ........................................................................................................... 69
Contents
DVD Dubbing
Dubbing DVDs Using the LAN Terminal ............................................................................................................................ 70
Introduction
Setup Menu
Overview of BD-X200 Functions ......................................................................................................................................... 4
Precautions for DVD Recorder Use ..................................................................................................................................... 5
Precautions for Disc Usage ................................................................................................................................................. 6
Details Regarding Discs ...................................................................................................................................................... 7
Setup Menu Configuration................................................................................................................................................. 74
Setting the Setup Menu ..................................................................................................................................................... 75
Restoring to Default Settings ....................................................................................................................................... 75
Setup Menus ..................................................................................................................................................................... 76
DISC MENU Screen .......................................................................................................................................................... 77
INPUT SELECT MENU screen ......................................................................................................................................... 77
SYSTEM MENU Screen.................................................................................................................................................... 78
PRESET STYLE MENU screen ........................................................................................................................................ 79
RECORDER MENU Screen .............................................................................................................................................. 80
REMOTE MENU screen .................................................................................................................................................... 82
DISPLAY MENU screen .................................................................................................................................................... 83
CLOCK ADJUST MENU screen........................................................................................................................................ 84
DUBBING screen .............................................................................................................................................................. 84
NETWORK MENU Screen ................................................................................................................................................ 85
Component Names & Functions
Front Panel .......................................................................................................................................................................... 9
Rear Panel......................................................................................................................................................................... 12
LCD Display and On-Screen Content
LCD Display....................................................................................................................................................................... 14
On-Screen Content ........................................................................................................................................................... 16
Status Messages ......................................................................................................................................................... 16
Disc Status................................................................................................................................................................... 18
Event Messages .......................................................................................................................................................... 19
Alarm Messages .......................................................................................................................................................... 20
Others
Preparation
Troubleshooting ................................................................................................................................................................. 85
Specifications .................................................................................................................................................................... 86
Signal Connections ........................................................................................................................................................... 21
Power Connections............................................................................................................................................................ 23
Turning the Power On & Off............................................................................................................................................... 24
Inserting & Removing Discs .............................................................................................................................................. 25
Using a Keyboard & Mouse ............................................................................................................................................... 26
Setting & Displaying the Date & Time................................................................................................................................ 27
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Overview of BD-X200 Functions
Precautions for DVD Recorder Use
Ⅵ Storage & Usage Locations
The storage and usage of this DVD recorder in the following
types of location should be avoided.
● Areas at temperatures which deviate by a significant degree
above or below the permitted service temperature range
(i.e., 5°C to 35°C).
ⅥVideo and audio signals from this DVD recorder’s input terminals can be recorded to
Precautions Regarding Condensation
DVD-R or DVD-RW (video mode only). (☞ Page 29)
ⅥCondensation
The types of signals that can be used are as follows.
When cold water is poured into a glass and droplets of
water form on its outer surface, this moisture is referred
to as “condensation”.
Video: Composite video, YC separate, or DV signals (including audio)
Audio: Analog audio or DV signals (including video)
● Areas at humidities which deviate by a significant degree
above or below the permitted service humidity range (i.e.,
20% to 80% RH).
● Areas where a large amount of dust or sand is present.
● Areas where the DVD recorder may come into contact with
oily smoke or steam, such as in kitchens or in their
immediate vicinity.
● Areas that are unstable or where significant vibration occurs.
● Areas where condensation occurs readily.
● Areas where strong magnetic fields are generated by
transformers, motors, or the like.
● Areas where transceivers, mobile phones, and other
wireless-communication devices are present.
● Areas that are subjected to X-ray irradiation or where
corrosive gases are present. (This precaution must be
strictly observed.)
ⅥWhen condensation occurs
ⅥA wide range of recording methods are supported. The appropriate method is to be
Condensation can cause water droplets to adhere to the
DVD recorder’s internal lens, thus making normal
operation impossible.
ⅥCondensation occurs easily in the following situations,
and the appropriate care should be taken.
• When the DVD recorder is moved from a cold location
into a warm room.
• When the room containing the DVD is rapidly heated.
• When an air conditioner’s air duct is pointing straight at
the DVD recorder.
ⅥIn situations where it is likely that condensation will occur,
remove any DVD that may be present in the BD-X200
and then turn the power on. As the interior heats up,
condensation will be less likely to occur.
ⅥCondensation is a principal cause of the inability to play
discs and other similar problems. In this type of situation,
allow the DVD recorder to remain inactive with its power
on for several hours. If the problem persists after this
period of time has elapsed, contact either the store where
the BD-X200 was purchased or your nearest JVC
Authorized dealer.
selected in accordance with the intended mode of use.
● The REC, PAUSE, and STOP buttons on the front panel can be used for standard operations. (☞ Page 39)
● Recording operations can be carried out using the REC CONTROL panel. Furthermore, a keyboard and mouse can also be
used when recording via this panel. (☞ Page 41)
●
The BD-X200 features an RS-422A terminal. When it is connected to an RS-422A compatible VCR, therefore, RS-422 control
can be used to carry out synchronous recording of the VCR’s video and audio to a DVD. (Various menu settings are required.)
Synchro-recording is carried out from the REMOTE CONTROL screen. (☞ Page 59)
● When a digital video camera or a DV player is connected to the BD-X200 using a DV cable, and when this DVD recorder is
setup as the master device for DV control (using menu settings), synchronous recording of any video and/or audio signals
from the DV player can be carried out to a DVD. Synchro-recording is carried out from the REMOTE CONTROL screen. (☞
Page 63)
● The DV IN/OUT terminal can be used to record audio and video from a non-linear editor to a DVD. In such a case, the BD-
X200 must be setup as the control slave (using menu settings).The DVD recorder will be controlled by the non-linear editor
in this type of setup. (☞ Page 64)
Ⅵ Handling
● Ensure that this DVD recorder is placed on a flat, horizontal
surface for use.
ⅥThe title and chapter menus can be created either automatically or manually. (☞ Page 43)
Five different patterns have been provided as display styles for the title and chapter menus.Each of these patterns is characterized
by different thumbnail characteristics (i.e., number, position, and size) and background images displayed on the title and
chapter menu screens.
When a display style is selected during the recording of content to a DVD, the BD-X200 will automatically create the title and
chapter menus in accordance with this style.
The PRESET STYLE MENU screen can be used to modify the thumbnail and background display characteristics of each of the
display styles.
In addition, the THUMBNAIL EDIT screen and the CHAPTER MENU EDIT screen can be used to modify the display style and
thumbnail images for chapter menus, and also to input chapter names and comments. The input of names or comments is
carried out using a keyboard connected to one of the recorder’s USB terminals.
● Do not place heavy objects such as a monitor on top of the
DVD recorder.
● Do not insert foreign objects into the disc tray opening.
● Be careful not to get your fingers clamped when loading
the disc to prevent injury.
● Do not block the fan’s ventilation holes.
● Avoid knocking or dropping this DVD recorder.
● When the DVD recorder is to be moved, ensure that any
DVD it contains is removed in advance.
● If the DVD recorder is not to be used for an extended period
of time, please disconnect the AC adaptor to avoid wasting
electricity.
Extended Periods of Inactivity
Performance may deteriorate over extended periods of
inactivity; for this reason, the power should be turned on
and the DVD recorder should be operated at regular
intervals.
The TITLE MENU EDIT screen can be used to modify the display style for the title menu and to enter title names.
ⅥDVD dubbing can be carried out using the LAN terminal.
Ⅵ Cleaning the Exterior (with the power off)
Use a soft cloth when cleaning the outside of this DVD
recorder.
This terminal allows two BD-X200 DVD recorders to be connected using a LAN cable, and the recorders can then operate as
master and receiver devices during the dubbing of DVDs. (☞ Page 70)
Compensation for Damaged Content
Do not use paint thinners or organic solvents as cleaning
agents.
Failure to observe these precautions can result in discoloration
or melting of exterior surfaces.
When stubborn dirt is present, wipe away using a cloth soaked
in a dilute neutral solvent.
ⅥJVC accepts no responsibility whatsoever for damages
incurred as a result of an inability to play or record audio
and video content in the rare event that this DVD recorder,
a DVD-R, or a DVD-RW fails to operate correctly.
ⅥIt is recommended that discs containing important content
be backed up at regular intervals (i.e., on a yearly basis).
Although digital signals do not deteriorate, storage
environments can have an effect on a disc’s aging
characteristics, and this may result in an inability to play
or record.
ⅥThe BD-X200 can be used to play discs that it has created. (☞ Page 57)
In this way, it is possible to inspect the content of discs finalized using this DVD recorder.
● Once a disc has been finalized, it can also be played on other DVD players.
Ⅵ Always use the AC adaptor provided with this DVD
recorder.
Ⅵ Always use the power cord provided with this DVD
recorder.
The usage of a different type of cord or a damaged cord can
result in the outbreak of fire or electric shocks.
ⅥIf a disc should break, there will be no way to recover
data from it.
ⅥProper playback of discs recorded using this DVD recorder
on all devices is not guaranteed.
Ⅵ
The power cord or the AC adaptor supplied with this
DVD recorder should not be used with any other device.
Ⅵ Before connecting the BD-X200 to other devices,
turn those devices off and then carry out setup
procedures as described in the corresponding
user’s manuals.
Ⅵ
The DVD drive unit is an expendable part. Although
the service life of the DVD drive unit differs depending
on the usage environment of the customer, replacement
every 1000 hours as a guide is recommended. (☞ Page
78 “TOTAL RECORDING TIME”)
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Precautions for Disc Usage
Details Regarding Discs
Care of Discs to Ensure High-Quality Playback
Discs for Recording & Playback
Finalizing
ⅥFingerprints, dust, or any other similar contamination of the surface of a disc can lead to distortion in the playback of recorded
video and audio. For this reason, it is good practice to wipe each disc with a soft cloth before use.
The following shows the discs that can be recorded to and played
using this DVD recorder, in addition to the corresponding display
marks or logos.
When a DVD-R or a DVD-RW (video mode) has been finalized,
it can be played in the same way as any other DVD using a
standard DVD player. (☞ Page 42)
Ⅵ Looking After Discs
● Using a soft cloth, wipe the disc gently from the inside to
the outside.
Ⅵ Handling Discs
● Removing a disc
Ⅵ Recording to unused sections of a disc and the
modification of titles or display styles can be carried
out as required before a disc is finalized.
● Placing a disc in its case
DVD-R
12 cm: 4.7 GB
General Version 2.0
(video mode)
•
In the case of both DVD-Rs and DVD-RWs, it is impossible
to overwrite previously recorded content with new data,
even if the disc in question has not yet been finalized.The
deletion of specific sections of data is also impossible.
Regardless of whether or not finalization has been carried
out, it will not be possible to use this DVD recorder to
record new content to a DVD-R or DVD-RW that has been
recorded using other devices.
DVD-RW
12 cm: 4.7 GB
Version 1.1 or later
(video mode)
● If stubborn dirt is present on the surface of a disc, wipe first
using a slightly wet cloth and then using a dry cloth.
● Paint thinners, organic solvents, analog record cleaning
agents, anti-static sprays, and the like must never be used.
Failure to observe this precaution can lead to discs being
permanently damaged.
•
● Correct method for holding a disc
Your hands or fingers should not
*
Certain characteristics and properties of DVD-Rs and DVD-
RWs can render them unsuitable for recording or playback.
come into contact with the
recording surface when holding
a disc.
Recommended manufacturers
DVD-R
DVD-RW : JVC, TDK 1×, 2×
Ⅵ Once a disc has been finalized, it can be used as a
standard DVD and its recorded audio and video can
be played on this and other DVD players.
:
JVC, Maxell, TDK 1×, 2×, 4×
Additional Notes on Disc Handling
Storing Discs
•
After finalizing, a disc’s titles can be selected from the top
menu.
•
•
Additional recording will not be possible after finalizing.
Although a finalized disc may in principle be played on
other DVD players, certain characteristics of the disc and
its recording conditions may make this impossible.
ⅥNever wipe a disc using paint thinners, organic solvents,
alcohol, or record-cleaning fluid.
ⅥDo not use disc protectors or scratch guards.
ⅥStickers and other types of paper label should not be applied.
ⅥDo not use discs from which stickers or labels have been
removed.
ⅥDo not use discs on which illustrations or text has been printed
using a commercially-available label printer.First create a disc
using the unit before printing.
ⅥThe use of non-circular discs (i.e., heart or rectangular
shaped), warped discs, and cracked discs can lead to
breakage of the DVD recorder.
ⅥAvoid storing discs in any of the following locations.
• Areas with high levels of humidity or dust, or areas where
mold is present.
• Areas exposed to direct sunlight or close to heating
equipment.
• Vehicle interiors during summer months.
ⅥTake care to avoid dropping or knocking discs.
ⅥPlace discs in cases and stack these cases for storage.
ⅥDiscs can be deformed or cracked as a result of stacking,
leaning, or dropping when not inside a case.
DVD-R & DVD-RW Details
DVD-R
:
Only discs that conform with DVD-R Standard 2.0
(video mode) can be used.
DVD-RW : Discs of Version 1.1 or later can be used.
Although Version 1.1 of the DVD-RW Standards
allows the selection of either video mode orVR mode
for recording, this DVD recorder performs recording
in video mode only.
* Version 1.0 of the DVD-RW Standards does not
support video-mode recording, and for this
reason, the corresponding discs cannot be used.
In terms of recording characteristics, DVD-R and DVD-RW (video
mode) differ as follows.
Playing Discs on the BD-X200
The BD-X200 is capable of playing any discs that it has created
and finalized.
● The following conditions may occur when attempting to
play discs recorded using other devices on this DVD
recorder.
Ⅵ DVD-R
•
Each disc can be recorded only one. Accordingly, these
discs are recommended for use in archiving or long-term
storage.
•
•
•
•
Inability to play
Block-type noise (i.e., mosaic)
Interruptions in audio and/or video
Unintentional stopping during playback
•
Once a disc has been finalized, it can also be played on
other DVD players.
● Commercially-available DVD-Videos and DVD-ROMs
cannot be used.
Ⅵ DVD-RW (video mode):
•
After viewing a disc, all data can be erased and it can be
used to record new content.
•
Once a disc has been finalized, it can also be played on
other DVD players.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Component Names & Functions
Details Regarding Discs (continued)
DVD Data Configuration
Front Panel
Region Codes
2
6
Generally speaking, the content recorded on a DVD is separated
into large units referred to as “titles”. A unique number called a
“title number” is assigned to each of these titles, and as a result,
any title can be immediately accessed using its title number. In
addition, each title can be divided into smaller units referred to
as “chapters”. Similarly, a unique number called a “chapter
number” is assigned to each of these chapters, and this allows
any chapter to be immediately accessed using its chapter
number.
Each recording made to a DVD-R or DVD-RW (video mode) is
stored as a single title. In this, each pressing of the STOP button
to leave Recording mode constitutes a different recording. (This
action is also referred to as “title closing”.)
One of six numbers referred to as “region codes” is assigned to
DVD content to control the global regions in which this content
may be viewed. If a DVD’s region code does not correspond to
the region code of the DVD player being used, it will not be
possible to play the disc.
● This DVD recorder assigns the region code “ALL” to the discs
that it records.
● It will not be possible to play discs to which region codes have
been assigned.
BUSY
3
OPERATE
OPEN/CLOSE
1
4
7
OPTION DV Y/C LINE
SET UP
DVD RECORDER BD-X200
TITLE
AUDIO
CHAPTER
CH1
CH2
DOLBY DIGITAL
LPCMMPEG
5
8
SET
TOP
PHONES
REV
STOP
PLAY
FWD
PAUSE
REC
MENU
MENU
Whenever the PAUSE button is pressed to pause recording, a
chapter mark is inserted into the current title. It is also possible
to insert chapter marks to partition titles at the desired points by
pressing the REC button while recording. In addition, your BD-
X200 can also be used to automatically insert chapter marks at
regular intervals. (CHAPTER CREATION menu settings will be
required for this function.)
Note
OPERATE button and indicator
1
The OPEN/CLOSE button will have no effect if pressed
while the DVD recorder is in either Recording or
Recording Pause mode. This is also the case when
performing finalizing, erasing, or dubbing.
● This button is used to turn on the DVD recorder and to
make it ready for use. When pressed a second time, this
button turns off the DVD recorder.
Screen Sizes
● The indicator’s lighting condition depends on the condition
of the DVD recorder and can be one of the following.
This DVD recorder is capable of recording video content for wide-
screen TVs (i.e., with a 16:9 aspect ratio).
In addition, signals for normal content with a 4:3 aspect ratio, for
squeezed content (i.e., where the left and right are compressed),
and for letterbox content (i.e., where the top and bottom of the
screen are black) can be recorded as is.
● Thumbnail creation method for use in the title/chapter menu
during wide-signal input can be selected in THUMBNAIL
FORM of the RECORDER (2/2) menu screen. (☞ Page 81)
Lit in green
Lit in red
Flashing in red
:
:
:
The DVD recorder’s power is on.
The DVD recorder’s power is off.
An error has occurred.
Audio level indicator
These meters are used to indicate the current level of audio
on Channel 1 and Channel 2.
Specifically, the audio level meters indicate the audio recording
levels when the DVD recorder is in Recording mode, and the
audio playback levels when it is in Playback mode.
(Adjustment of the audio recording levels: ☞ Page 35.)
5
DVD-R or DVD-RW
Notes
● The OPERATE button will have no effect if pressed
while the DVD recorder is in either Recording or
Recording Pause mode. This is also the case when
performing finalizing, erasing, or dubbing.
● The DVD recorder continues to use a small amount
of power even after it has been turned off using the
OPERATE button.If it will not be used for an extended
period of time, please disconnect the AC adaptor to
avoid wasting electricity.
Title 2
Chapter 1 Chapter 2
Title 1
Chapter 1 Chapter 2 Chapter 3
LCD display
6
7
The LCD display is used to present important information.
During recording or playback, for example, the title, chapter
number, and elapsed time are indicated on the LCD display.
(☞ Page 14 for more details.)
● Before a title is closed, it will be possible to modify the style
used for chapter menu display, to change the thumbnails used,
and to input thumbnail names.
● Before a disc is finalized, it will be possible to modify the style
used for the title menu and to input title names.
● Do not disconnect the DC cord or power cord when
in Operate On mode as this can result in the DVD
recorder being damaged.
● Malfunction may occur when switching to OPERATE
ON while pressing a key on a connected USB
keyboard.
Video input indicators
Ⅵ OPTION indicator
This indicator is lit up or flashes when INPUT SELECT
from the INPUT SELECT MENU screen has been set to
OPTION.(This setting cannot be carried out using the DVD
recorder alone.)
Ⅵ DV indicator
Disc tray
2
This indicator is lit up or flashes when INPUT SELECT
from the INPUT SELECT MENU screen has been set to
DV. Specifically, the indicator is lit up when an input signal
is present, and it flashes when no signal is present.
The purpose of the disc tray is to hold DVDs.
This tray opens automatically when the OPEN/CLOSE button
is pressed. In addition, the OPEN/CLOSE button can be
pressed again to close the tray.
Notes
Ⅵ Y/C indicator
● Do not push the disc tray as it is opening or closing.
● Do not place objects other than discs on the disc
tray.
This indicator is lit up or flashes when INPUT SELECT
from the INPUT SELECT MENU screen has been set to
Y/C.Specifically, the indicator is lit up when an input signal
is present, and it flashes when no signal is present.
● Do not press down on the disc tray
Ⅵ LINE indicator
BUSY indicator
3
4
This indicator is lit up or flashes when INPUT SELECT
from the INPUT SELECT MENU screen has been set to
LINE.Specifically, the indicator is lit up when an input signal
is present, and it flashes when no signal is present.
This indicator flashes when the DVD recorder is in Recording
Pause mode or when it is performing time-consuming
operations such as title closing, finalizing, and erasing. None
of the DVD recorder’s buttons will have any effect if pressed
while the BUSY indicator is flashing.
Phones jack and volume adjuster
8
The phones jack allows headphones to be connected to the
DVD recorder for monitoring of audio levels; in addition, the
headphone volume can be adjusted using the volume adjuster.
Note that this adjuster has no effect on the actual recording
levels.
OPEN/CLOSE button and indicator
This button is used to open and close the disc tray.
In addition, the OPEN/CLOSE indicator is lit up while the disc
tray is opening, and also when it is open.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Component Names & Functions
Front Panel (continued)
SET UP button
[8] button
&
)
⁄
¤
● This button can be pressed to display the Setup Menu on
the monitor. A wide range of different menu settings can
then be made via the Setup Menu. (☞ Page 74)
In addition, the SET UP button can be pressed again to
hide the Setup Menu.
● If a title menu or chapter menu is displayed, this button can
be used to select a menu number for playback.Specifically,
pressing of this button moves the selection position to the
left.
BUSY
OPERATE
OPEN/CLOSE
● This button can be pressed while the DVD recorder is
playing to move playback to the start of the current chapter.
● The 8 button can be used to adjust the audio recording
levels when the DVD recorder is stopped or in Recording
Pause mode.
• If AUDIO REC VOLUME MODE from the RECORDER
MENU (2/2) screen is set to INDEPENDENCE and either
the 6 or 7 button is pressed while this button is being
held, the audio recording level for Channel 1 will be
adjusted accordingly.
• If AUDIO REC VOLUME MODE from the RECORDER
MENU (2/2) screen is set to BOTH and either the 6 or 7
button is pressed while this button is being held, the audio
recording levels for both Channel 1 and Channel 2 will be
adjusted accordingly.
• If this button is pressed together with the t button, the
audio recording levels will be returned to their default
settings (i.e., unity gain).
● If the SET UP button is pressed in Recording or Recording
Pause mode, setting data relevant to recording (i.e., video
bit rate and audio encoding format) will be displayed on-
screen.In addition, the SET UP button can be pressed again
to hide this information.
)
*
&
OPTION DV Y/C LINE
SET UP
DVD RECORDER BD-X200
TITLE
AUDIO
CHAPTER
CH1
CH2
DOLBY DIGITAL
LPCMMPEG
SET
TOP
PHONES
REV
STOP
PLAY
FWD
PAUSE
REC
⁄
¤
MENU
MENU
[6] button
*
● This button is used to select menu items or setting values
when the Setup Menu is displayed.
● If a title menu or chapter menu is displayed, this button can
be used to select a menu number for playback.Specifically,
pressing of this button moves the selection position upward.
● The 6 button can be used to adjust the audio recording
levels when the DVD recorder is stopped or in Recording
Pause mode.
• If AUDIO REC VOLUME MODE from the RECORDER
MENU (2/2) screen is set to BOTH and this button is
pressed while either the 8 or t button is being held, the
audio recording levels for both Channel 1 and Channel 2
will increase.
• If AUDIO REC VOLUME MODE from the RECORDER
MENU (2/2) screen is set to INDEPENDENCE and this
button is pressed while the 8 button is being held, the
audio recording level for Channel 1 will increase.Similarly,
if the 6 button is pressed while the t button is being
held, the audio recording level for Channel 2 will increase.
9
0
!
@
#
#
$ % ^
(
REV button and indicator
PAUSE button and indicator
9
● When this button is pressed in Playback or Fast-Forward
Play mode, the DVD recorder switches to fast-reverse play.
If pressed again during fast-reverse play, the REV button
toggles the speed of fast-reverse between ×3 and ×15.
● When this button is pressed in Still or Slow-Forward Play
mode, the DVD recorder switches to slow-reverse play. If
pressed again during slow-reverse play, the REV toggles
the speed of slow-reverse between ×0.5 and ×0.06.
● The REV indicator is lit up during fast-reverse and slow-
reverse play.
● If this button is pressed during recording, the DVD recorder
switches to Recording Pause mode. A chapter mark is
inserted at the corresponding point.
● If this button is pressed during playback, the DVD recorder
switches to Still mode and freezes playback. If the PAUSE
button is then pressed again in Still mode, the DVD recorder
will advance playback by a single field.
● The PAUSE indicator is lit up in Recording Pause and Still
modes.
REC button and indicator
● If this button is pressed together with the PLAY button in
Stop mode, recording will be started.
[t] button
● If a title menu or chapter menu is displayed, this button can
be used to select a menu number for playback.Specifically,
pressing of this button moves the selection position to the
right.
$
● This button can be pressed while the DVD recorder is
playing to move playback to the start of the next chapter.
● The t button can be used to adjust the audio recording
levels when the DVD recorder is stopped or in Recording
Pause mode.
• If AUDIO REC VOLUME MODE from the RECORDER
MENU (2/2) screen is set to INDEPENDENCE and either
the 6 or 7 button is pressed while this button is being
held, the audio recording level for Channel 2 will be
adjusted accordingly.
• If AUDIO REC VOLUME MODE from the RECORDER
MENU (2/2) screen is set to BOTH and either the 6 or 7
button is pressed while this button is being held, the audio
recording levels for both Channel 1 and Channel 2 will be
adjusted accordingly.
• If this button is pressed together with the 8 button, the
audio recording levels will be returned to their default
settings (i.e., unity gain).
STOP button
● This button has the following effect when pressed in
Recording or Recording Pause mode.
If EDIT MENU from the SYSTEM MENU screen is set to
DISABLE, the DVD recorder stops recording (i.e., it
performs title closing).
If EDIT MENU from the SYSTEM MENU screen is set to
ENABLE, the DVD recorder stops recording and the
THUMBNAIL EDIT screen is displayed. It will then be
possible to modify the chapter menu.
0
• If the current disc is blank or title closing has been carried
out, a new title will be created and recording will start at
Chapter 1.
[7] button
(
● This button is used to select menu items or setting values
when the Setup Menu is displayed.
● When this button is pressed during recording, a new chapter
will be setup within the continuous video data.
● If this button is pressed and held for more than 2 seconds
while the DVD recorder is stopped or inserted with no disc,
input signal encoded/decoded in MPEG will be output via
theVIDEO OUT terminal on the rear panel.This will continue
for as long as the button is held, and it allows the DVD
recording quality to be confirmed. Audio will be muted at
this time.
● The REC indicator is lit up in Recording and Recording
Pause modes.
TOP MENU button
If this button is pressed while the DVD recorder is in a playback
condition, the current DVD’s top menu (or title menu) will be
displayed on the monitor screen.
If the DVD does not contain a title menu, nothing will be
displayed when the TOP MENU button is pressed.
● If a title menu or chapter menu is displayed, this button can
be used to select a menu number for playback.Specifically,
pressing of this button moves the selection position
downward.
● The 7 button can be used to adjust the audio recording
levels when the DVD recorder is stopped or in Recording
Pause mode.
• If AUDIO REC VOLUME MODE from the RECORDER
MENU (2/2) screen is set to BOTH and this button is
pressed while either the 8 or t button is being held, the
audio recording levels for both Channel 1 and Channel 2
will decrease.
• If AUDIO REC VOLUME MODE from the RECORDER
MENU (2/2) screen is set to INDEPENDENCE and this
button is pressed while the 8 button is being held, the
audio recording level for Channel 1 will decrease.Similarly,
if the 7 button is pressed while the t button is being
held, the audio recording level for Channel 2 will decrease.
● When the STOP button is pressed in Playback mode, the
DVD recorder stops playback.
PLAY button and indicator
!
● If this button is pressed together with the REC button while
a recordable disc is inserted into the DVD recorder,
recording will be started.
● When the PLAY button is pressed in Recording Pause
mode, the DVD recorder restarts recording.
● If a finalized disc has been inserted into the DVD recorder,
pressing of this button will start playback.
● The PLAY indicator is lit up in Recording and Playback
modes.
%
^
SET button
● This button is used to confirm the selection of menu items
or setting values when the Setup Menu is displayed.
● When this button is pressed during normal screen display,
the counter from the DVD recorder’s LCD display will switch
to display of either the elapsed recording/playback time or
the remaining disc/title time.
MENU button
FWD button and indicator
@
If this button is pressed while the DVD recorder is in a playback
condition, the chapter menu for the currently selected title
will be displayed on the monitor screen.
● When this button is pressed in Playback or Fast-Reverse
Play mode, the DVD recorder switches to fast-forward play.
If pressed again during fast-forward play, the FWD button
toggles the speed of fast-forward between ×3 and ×15.
● When this button is pressed in Still or Slow-Reverse Play
mode, the DVD recorder switches to slow-forward play. If
pressed again during slow-forward play, the FWD toggles
the speed of slow-forward between ×0.5 and ×0.06.
● The FWD indicator is lit up during fast-forward and slow-
forward play.
If the DVD title does not contain a chapter menu, nothing will
be displayed when the MENU button is pressed.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Component Names & Functions
Rear Panel
2
1
3
4
5
$
VIDEO
LINE
AUDIO
IN
VIDEO
LINE
AUDIO
IN
IN
OUT
INPUT
LEVEL
CH1
IN
OUT
INPUT
LEVEL
CH1
OUT
OUT
4dB
8dB
4dB
8dB
Y/C
Y/C
6
IN
IN
CH2
CH2
REMOTE
REMOTE
DV IN/OUT
DV IN/OUT
8
!
USB
LAN
USB
LAN
SIGNAL
GND
SIGNAL
GND
DC 19V
DC 19V
7
9
#
0
@
VIDEO LINE IN terminal (BNC)
This terminal allows composite video signals to be input to
the DVD recorder.
In order to select these signals for input, set INPUT SELECT
from the INPUT SELECT MENU screen to LINE.
● SETUP from the SYSTEM MENU screen should be set in
accordance with whether or not this input signal is a setup
signal. (U-model only)
AUDIO IN terminals (RCA × 2)
RS-422A REMOTE terminal (D-sub 9-pin male)
DC IN terminal (2-pin)
!
1
5
6
8
These terminals allow analog audio signals to be input to the
DVD recorder.
This terminal is used to connect the DVD recorder to a VCR
capable of being controlled via RS-422A. RS-422A control of
a VCR using the RS-422A REMOTE terminal is carried out
with the DVD recorder operating in Master mode.
● In order to use this terminal, set REMOTE SELECT from
the REMOTE MENU screen to 9PIN(MASTER).
Video and audio from the VCR can be recorded to a DVD
using commands issued from the REMOTE CONTROL
screen. (☞ Page 59)
This terminal is used to provide DC at 19 V to the DVD
recorder.The DC power cord from the AC adaptor (included)
should be connected here.
● In order to select these signals for input, set INPUT SELECT
from the INPUT SELECT MENU screen to LINE or Y/C.
Note
When power is supplied via this terminal, the OPERATE
indicator on the front panel lights up in red.
AUDIO OUT terminals (RCA × 2)
These terminals allow analog audio signals to be output from
the DVD recorder.
● When the DVD recorder is in Stop or Recording mode, the
audio input signals (i.e., E-E signals) are output via these
terminals.
VIDEO Y/C IN terminal (4-pin)
This terminal allowsYC separate video signals to be input to
the DVD recorder.
DC power cord clamp
2
@
This clamp secures the DC power cord in place, and it should
always be used to prevent accidental disconnection.
LAN terminal (RJ-45)
9
In order to select these signals for input, set INPUT SELECT
from the INPUT SELECT MENU screen to Y/C.
● SETUP from the SYSTEM MENU screen should be set in
accordance with whether or not this input signal is a setup
signal. (U-model only)
● This terminal’s specification (i.e., S1 or S2) can be selected
usingY/CTERMINAL MODE from the RECORDER MENU
(2/2) screen.
● Audio from the DVD is output when in Playback mode.
● When two DVD recorders are used to perform DVD-to-DVD
dubbing, this terminal is connected to both BD-X200s. A
cable of Category 5 or better is required for this connection.
A cross-type Ethernet cable is required when connecting
directly to another BD-X200.
SIGNAL GND terminal
#
$
DV IN/OUT terminal
This I/O terminal for digital signals conforms with IEEE1394
specifications.
As such, it allows the DVD recorder to be connected to DV
cameras, DVVCRs, and non-linear editors with DV terminals.
● In order to select this terminal’s audio and video signals for
input, set INPUT SELECT from the INPUT SELECT MENU
screen to DV.
7
This terminal is used to ground signals.
Optional-board slot cover
This cover is removed to allow commercially-available optional
boards to be installed.
● This terminal is also used when connecting to a PC on
which BD-X200 utility software for operations such as the
creation of the title and chapter menus has been installed.
● Network settings must be carried out using the NETWORK
MENU screen.
VIDEO LINE OUT terminal (BNC)
3
This terminal is used to connect the DVD recorder to a monitor.
● When the DVD recorder is in Stop or Recording mode, the
video input signal is output on the E-E screen as a
composite video signal.
● REMOTE SELECT from the REMOTE MENU screen is
used to select a control method for this terminal as follows.
USB terminals (2)
0
DV(MASTER)
DV(SLAVE)
:
:
:
The DVD recorder operates as the
master device and controls a DV camera
or VCR.
The DVD recorder operates as a slave
device and is controlled by commands
from a non-linear editor.
The DVD recorder performs recording
in response to operation of the trigger
button on a camera capable of DV
triggering (i.e., a GY-DV5000).
These terminals are used when connecting the DVD recorder
to USB devices such as a keyboard or mouse.
A keyboard and mouse can be used as an alternative to the
DVD recorder’s buttons when using setting and control
screens.
● If the REC button is pressed and held for at least 2 seconds
while the DVD recorder is stopped, the input signal will be
subjected to MPEG encode/decode processing and output
via the VIDEO LINE OUT terminal.This will continue for as
long as the REC button is held, and it allows the DVD
recording quality to be confirmed.
● Playback from the DVD is output as a composite signal
when in Playback mode.
● The Setup Menu, title menu, chapter menus, and other
setting and control screens are displayed on the monitor
connected to this terminal.
The input of text in setting screens is carried out using a
keyboard.
DV(TRIGGER)
● It is not be possible to operate devices other than a keyboard
or mouse by connecting them to the USB terminal.
● Set KEYBOARD STYLE from the SYSTEM MENU screen
in accordance with the keyboard’s input language.
Recommended manufacturers: Logitech
● Status and alarm information is also displayed on-screen.
(The DISPLAY MENU screen can be used to indicate which
items are to be displayed.)
AUDIO INPUT LEVEL switch
4
This switch is used to set the standard level for audio input.
+4dB : The standard level is set to +4 dB.
–8dB : The standard level is set to –8 dB.
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Display and On-Screen Content
LCD Display
The following information and data is presented on the DVD recorder’s LCD display.
BUSY
BUSY
OPERATE
OPEN/CLOSE
OPERATE
OPEN/CLOSE
OPTION DV Y/C LINE
SET UP
OPTION DV Y/C LINE
SET UP
DVD RECORDER BD-X200
TITLE
DVD RECORDER BD-X200
TITLE
AUDIO
CHAPTER
AUDIO
CHAPTER
CH1
CH2
DOLBY DIGITAL
LPCMMPEG
CH1
CH2
DOLBY DIGITAL
LPCMMPEG
SET
SET
TOP
PHONES
REV
STOP
PLAY
FW
PAUSE
REC
TOP
PHONES
REV
STOP
PLAY
FWD
PAUSE
REC
MENU
MENU
MENU
MENU
TITLE
CHAP
CHAP
TITLE
DOLBYDIGITAL
LPCM
DOLBYDIGITAL
LPCM
1
2
2
No.
Description
No.
Description
ⅥIndication of the current operating mode
Encoding format for audio recordings (LPCM, DOLBY DIGITAL)
Recording mode : The encoding format set using AUDIO ENCODE from the RECORDER MENU (1/2) screen is
displayed.
2
1
PLEASE WAIT
OPERATE OFF
NO DISC
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
The DVD recorder is starting up.
The DVD recorder is preparing to shut down.
The DVD recorder currently contains no disc.
Playback mode
:
The encoding format used for audio on the current disc is displayed.
LOADING
DVD-R
DVD-RW
A disc is being loaded into the DVD recorder.
Information relevant to the current mode.
ⅥTitle number / Chapter number / Counter
● When in Recording mode, the LCD display indicates the title number and chapter number currently being recorded,
in addition to either the elapsed title-recording time or the remaining disc space.
2
The current disc is a non-finalized DVD-R. (Approximately 3 seconds)
The current disc is a non-finalized DVD-RW. (Approximately 3 seconds)
The current disc is a finalized DVD-R or DVD-RW. (Approximately 3 seconds)
The DVD recorder is switching from Recording mode to Recording Pause mode.
The DVD recorder is switching from Recording mode to Stop mode.
A title menu or chapter menu is currently being edited.
The current disc is being ejected.
DVD
REC PAUSE
REC STOP
MENU EDIT
EJECT
The SET button can be pressed to toggle between display of the elapsed recording time and the remaining disc
space in the counter area.
TITLE
CHAP
TITLE CLOSE
FINALIZE
ERASE
TOP MENU
MENU
The DVD recorder is performing title-close processing.
The DVD recorder is finalizing the disc.
The DVD recorder is erasing data from a DVD-RW disc.
The disc’s top menu is being played.
Elapsed title-recording time (Hour:Minute:Second)
Remaining disc space
(Hour:Minute)
SET button
TITLE
CHAP
A menu is being played.
ENCODING XX
Encoded video is being output. (XX indicates the bit rate.)
ⅥDisplay of the Setup Menu
● When in Playback mode, the LCD display presents the title number and chapter number currently being played,
in addition to either the elapsed title-playback time or the remaining title-playback time.
Menu items and setting values from the Setup Menu are displayed. (☞ Page 74)
The SET button can be pressed to toggle between display of elapsed and remaining title-playback time in the
counter area.
ⅥEvent messages
Messages relating to incorrect operation and the like are displayed for approximately 3 seconds. (☞ Page 19)
Note
The remaining disc and title time depend on the amount of data comprising video, and for this reason, they
should be taken as being a general indication and not an exact figure.
ⅥAlarm messages
Alarms are displayed when the DVD recorder cannot obey a command. (☞ Page 20)
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Display and On-Screen Content
Status Messages (continued)
On-Screen Content
In addition to E-E and playback screens, the monitor connected to the DVD recorder’s VIDEO LINE OUT terminal can display the
following.
Status Messages
000 min
● Status messages
4
● Event messages
● Alarm messages
● The Setup Menu (☞ Page 74)
● Recording-operation control screens: REC CONTROL panel (☞ Page 41)
REMOTE CONTROL screen (☞ Page 60)
5
3
FINALIZE
DISC TITLE
Status Messages
REC
The DVD recorder’s setting condition and operation status are indicated by status messages, and these messages are displayed
on E-E or playback screens.
TITLE 1 0:11:22
04/05/04
11:20:00
2
CHAPTER
1
0:11:22
The DISPLAY MENU screen can be used to indicate whether or not status messages are to be displayed.
No.
Item
Description
DISPLAY MENU screen
Use TITLE/CHAPTER from the DISPLAY MENU screen to indicate whether or not this
is to be displayed.
Recording mode : The title number and chapter number currently being recorded are
displayed together with the elapsed title-recording time (in hours,
minutes, and seconds).
Title number / Chapter
number / Counter
Ⅵ To display status messages:
Set DISPLAY from the DISPLAY MENU screen to ON.
Ⅵ The various items of status information for display can be selected.
Ⅵ If DISPLAY is set to OFF, no status information will be displayed.
2
DISPLAY MENU
MENU
DISPLAY
ON
ON
TITLE/CHAPTER
RECORDER MODE
TIME/DATE
ON
Playback mode
:
The title number and chapter number currently being played are
displayed together with the elapsed title-playback time (in hours,
minutes, and seconds).
TIME+DATE
ON
REMAIN
MM/DD/YY
DATE STYLE
(DD/MM/YY:
E-model)
Use TIME/DATE from the DISPLAY MENU screen to select the way in which the date
and time are displayed.
Date / Time
3
OFF
DATE
TIME
: No information is displayed.
: Only the date is displayed.
: Only the time is displayed.
Status Messages
Data relevant to recording:
000 min
TIME+DATE : Both date and time are displayed.
● The date display style can be changed using DATE STYLE from the DISPLAY MENU
screen.
Recording mode : The date and time from the internal clock are displayed.
Playback mode
If the SET UP button is pressed
while in Recording mode, the
video bit-rate setting and the audio
encoding format will be displayed.
If the SET UP button is then
pressed once again, this
information is removed from the
screen.
:
The date and time of disc finalizing are displayed.
Use REMAIN from the DISPLAY MENU screen to indicate whether or not this is to be
displayed.
Recording mode : The amount of video that can still be recorded on the current disc is
displayed (in minutes).
Playback mode
Remaining time
4
5
FINALIZE
DISC TITLE
REC
:
Not displayed
1
04/05/04
11:20:00
TITLE 1 0:11:22
CHAPTER
* Remaining time is to be used as a general guide, not as an exact figure.
1
0:11:22
REC CONTROL panel
Provided that a recordable disc has been inserted, this panel will be displayed whenever
REC CONTROL from the REMOTE MENU screen is set to ON.
The REC CONTROL panel can be used to control recording operations. (☞ Page 41)
No.
Item
Operation Mode
Description
This area indicates the DVD recorder’s current mode of operation.
1
Use RECORDER MODE from the DISPLAY MENU screen to indicate whether or not
this is to be displayed.
NO DISC
EJECT
OPE OFF
STOP
REC
REC PAUSE
PLAY
:
:
:
:
:
:
:
:
:
:
:
:
The DVD recorder currently contains no disc.
The current disc is being ejected.
Operate Off mode
Stop mode
Recording mode
Recording Pause mode
Playback mode
Still mode
Fast-forward play at 3 times normal speed
Fast-forward play at 15 times normal speed
Fast-reverse play at 3 times normal speed
Fast-reverse play at 15 times normal speed
STL
FWD × 3
FWD × 15
REV × 3
REV × 15
SLOW FWD 0.50 : Slow-forward play at 0.5 times normal speed
SLOW FWD 0.06 : Slow-forward play at 0.06 times normal speed
SLOW REV 0.50 : Slow-reverse play at 0.5 times normal speed
SLOW REV 0.06 : Slow-reverse play at 0.06 times normal speed
LOADING
:
A disc is being loaded.
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Display and On-Screen Content
Event Messages
On-Screen Content (continued)
Event messages are displayed on the DVD recorder’s LCD display and on the monitor when incorrect operations are attempted.
These messages will remain on-screen for approximately 3 seconds.
Disc Status
Monitor screen
When a disc is inserted into the DVD recorder, one of the following disc status messages is displayed on the monitor screen.
000 min
LCD display
DOLBYDIGITAL
LPCM
090 min
Event messages:
Displayed when
DISPLAY from
TITLE FULL
the DISPLAY
MENU screen is
set to ON.
Event message
DVD-RW
Disc status
REC
04/05/04
11:20:00
TITLE 1 0:11:22
CHAPTER
1
0:11:22
REC
04/05/04
11:20:00
TITLE 1 0:00:00
CHAPTER 0:00:00
1
LCD display
message
Monitor message
INVALID TV
Description
A signal of an invalid format has been input.
Alternatively, an attempt has been made to play a disc containing signals of an invalid
format.
*: The disc status is not displayed if DISPLAY from the DISPLAY MENU screen is set to OFF.
INVALID TV
Status
DVD-R
Description
The current disc is a non-finalized DVD-R. (Approximately 3 seconds)
The current disc is a non-finalized DVD-RW. (Approximately 3 seconds)
The current disc is a finalized DVD-R or DVD-RW. (Approximately 3 seconds)
TITLE FULL
CHAPTER FULL
NOT FINALIZE
————
TITLE FULL
CHAP FULL
NOT FINAL
A L-xxxx-R
D L-xxxx-R
————
Recording was attempted on a disc already containing 99 titles.
An attempt was made to add a chapter to a title already containing 99 chapters.
An attempt was made to eject a disc before it was finalized.
DVD-RW
DVD
INVALID DISC The current disc is neither a DVD-R nor DVD-RW.
Set value is displayed when changing the recording level of analog audio.
Set value is displayed when changing the recording level of digital audio.
————
DURATION OVER
Auto Edit was carried out when the remaining disc space became insufficient during
RS-422A or DV remote operation.
INVALID EDL
————
————
————
An incorrect value was entered during the registration of an edit list (EDL).
EDL Load was carried out after starting the registration of an edit list (EDL).
EDL UNDER EDIT
NO CASSETTE
During RS-422A or DV remote operation, an attempt was made to control the
connected VCR while it did not contain a video tape.
NOT CONNECT
EDIT FAILURE
————
————
During RS-422A or DV remote operation, a control operation was attempted while
no external device was connected.
Editing could not be completed normally.
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Display and On-Screen Content
Preparation
Alarm Messages
Signal Connections
Alarm messages are displayed on the DVD recorder’s LCD display and on the monitor when the recorder cannot obey a command.
These messages will remain on-screen until the next operation is carried out.
Ⅵ Audio and video signals
Monitor screen
000 min
LCD display
Video outputs for VCR
DOLBYDIGITAL
LPCM
Note 1
Input
Alarm messages:
Displayed when
DISPLAY from the
Composite
DV
REC INHIBIT
DISPLAY MENU
screen is set to
ON.
Alarm message
Audio outputs for VCR
Monitor or TV
YC separate
Note 2
Input
REC
04/05/04
11:20:00
TITLE 1 0:11:22
Composite
Analog audio
DV
CHAPTER
1
0:11:22
Analog audio
Note 4
Note 3
LINE OUT
LCD display
message
DV IN/OUT
Y/C IN
LINE IN
Monitor message
Description
The current disc is not a DVD-R or DVD-RW.
VIDEO
LINE
AUDIO
CH1
IN
IN
OUT
INPUT
LEVEL
OUT
4dB
8dB
INVALID DISC
NOT X200
INVALID DISC
NOT X200
AUDIO OUT
Y/C
IN
A disc recorded using a different DVD recorder was inserted or played.
CH2
REMOTE
Headphones
DV IN/OUT
USB
LAN
PHONES
SIGNAL
GND
DC 19V
DV IN/OUT
REC INHIBIT
REC INH
● Recording was attempted using a disc on which no more data can be recorded.
● The current disc is a non-finalized DVD-RW to which no more data can be recorded.
(on front panel) Stereo
AUDIO IN
Note 5
COPY INHIBIT
DISC FULL
COPY INH
DISC FULL
CELL OVER
Recording of a copy-protected signal was attempted.
All remaining space on the disc is used up during recording.
同期信号発生器
CELL OVER
The number of cells for a single title exceeded 255.
This will be displayed when the recording time for a single title is exceeded as a
result of setting ENCODE QUALITY to a low value (i.e., 4 Mbps or lower), recording
content with little movement, or other similar factors. No error will be triggered when
the time is within that set for the total content.
Note 1: The video signal for input is selected using INPUT SELECT from the INPUT SELECT MENU screen.
Note 2: The audio signals for input are selected using INPUT SELECT from the INPUT SELECT MENU screen.
REGION CODE
OVERHEATING!
REGION CODE
OVERHEATING
An attempt was made to play a disc for which a region code has been set.
When either LINE orY/C is set for INPUT SELECT, the analog audio signals from the AUDIO IN terminals will be selected
for input.
When DV is set for INPUT SELECT, the DV audio signals from the DV IN/OUT terminal will be selected for input.
Note 3: When the DVD recorder is in Stop or Recording mode, the video input signal is output on the E-E screen as a composite
video signal.
Displayed when the internal temperature of the set rises due to fan malfunction, etc.
In this case, immediately turn off the power and discontinue use. The power will
automatically shut down in about 20 minutes after the OVERHEATING display.
In addition, the Setup Menu and other setting screens are also displayed on the monitor connected to this terminal. The
DVD recorder’s operation status and other relevant information are displayed on-screen when DISPLAY from the DISPLAY
MENU screen has been set to ON.
Note 4: The Y/C IN terminal’s specification (i.e., S1 or S2) can be selected using Y/C TERMINAL MODE from the RECORDER
MENU (2/2) screen.
Note 5: The standard input level for audio signals input via the AUDIO IN terminals (i.e., +4 dB or –8 dB) can be selected using the
AUDIO INPUT LEVEL switch on the rear panel.
CAUTION
If alarm messages such as “INVALID DISC” are displayed several times when a disc recorded using the BD-X200 or a blank
disk is inserted, there is a possibility that the disc itself has been damaged. In such a case, the damaged disc should be
replaced with a new one.
If the alarm messages continue to appear after replacing the disc, the problem may lie within the DVD recorder, and in such a
case, you are recommended to contact either the store where this BD-X200 was purchased or your nearest JVC authorized
dealer.
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Signal Connections (continued)
Power Connections
Ⅵ Control signals
Connect the AC adaptor (included) to the DVD recorder.
VIDEO
LINE
AUDIO
IN
IN
OUT
INPUT
LEVEL
CH1
OUT
4dB
8dB
Y/C
DV camera or VCR
IN
CH2
REMOTE
DV IN/OUT
CH-1
CH-2
AUDIO
LEVEL
USB
LAN
RS-422A compatible VCR
SIGNAL
GND
DC 19V
N
D
F
I
L
T
E
R
IRIS
FOCUS
ON
AUTO
MANU
OFF
DV CAMCORDER GY-DV300
PUSH
AUTO
COMPONENT
REMOTE2
VIDEO
AC adaptor
LINE
IN
Y/C
Power cord
(included)
IN
R-Y
B-Y
Y
(included)
AUDIO
CH 1/3 CH 2/4
OUT
DC IN
Note 3
DV cable
OUT
IN
DV
Clamp
OUT
AC
MONITOR
OUT
Screw
IN
OUT
OUT
SYNC IN
TIME CODE
IN
OFF
REC
PLAY
DV
IN/OUT
MONITOR
OUT
SERIAL
REMOTE
TIMER
SINGLE
GND
DC12V
REMOTE1
RS-422 REMOTE
Note 1
Note 2
DV IN/OUT
Remote cable
1. Connect the AC adaptor’s DC cord to the DVD
recorder’s DC IN terminal.
Nonlinear editing system
REMOTE
VIDEO
AUDIO
CH1
IN
LINE
OUT
INPUT
LEVEL
IN
OUT
4dB
8dB
OPERATE
2. Secure the DC cord using the DC power cord
clamp in order to prevent accidental
disconnection.
q Remove the screw and then the clamp.
w Insert the DC cord into the clamp, and then secure the
clamp to the DVD recorder.
OPERATE
indicator
Y/C
IN
CH2
BD-X200
REMOTE
DV IN/OUT
AC adaptor (included)
DC IN
USB
Power cord (included)
AC
LAN
SIGNAL
GND
AUDIO
CH1
DC 19V
CH2
LAN
PHONES
REV
3. Connect the power cord (included) to the AC
adaptor’s AC IN terminal.
USB
Note 4
4. Insert the power cord into an electrical outlet.
● Power will be supplied to the DVD recorder and the
OPERATE indicator will be lit up in red.(Operate Off mode)
Keyboard
Category 5 cable
Print
Pause
Break
Scroll
Lock
Esc
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
Screen
Sysrq
Mouse
Note
！
1
#
3
$
4
%
5
&
6
(
8
)
9
～
=
-
”
2
'
7
Back
Page
Up
Num
Lock
Insert
Home
End
/
Space
-
^
￥
」
*
9
0
Q
W
E
R
T
Y
U
I
O
P
｀
「
]
7
4
1
0
8
Page
Tab
Enter
Delete
Down
[
@
A small amount of current will be required by the DVD
recorder when in Operate Off mode.
+
Caps Lock
＋
＊
A
S
D
F
G
H
J
K
L
5
2
6
;
:
つ
<
,
、
>
.
。
Z
X
C
V
B
N
M
?
/
・
＿
Shift
Shift
/
Enter
.
Ctrl
Alt
Alt
Ctrl
CAUTION
● Always use the AC adaptor provided with the DVD
recorder.
The use of other power sources should be avoided.
● Do not disconnect the DC cord or power cord during
recording or playback.
In the case of DVD-R discs, failure to observe this
precaution will result in the discs becoming unusable.
In the case of DVD-RW discs, it will be necessary to erase
all data from the disc and to start recording again from
the beginning.
LAN
BD-X200
BUSY
OPERATE
OPEN/CLOSE
OPTION DV Y/C LINE
SET UP
AUDIO
CH1
CH2
SET
PHONES
REW
STOP
PLAY
FF
P
AUSE
REC
TOP
M
E
N
U
M
E
N
U
Receiver device
Note 1: In order to use the RS-422A REMOTE terminal, set REMOTE SELECT from the REMOTE MENU screen to 9PIN(MASTER).
Note 2: In order to carry out control using the DV IN/OUT terminal, make the appropriate selection using REMOTE SELECT from
the REMOTE MENU screen.
Note 3: One of the following DV cables should be used.
VC-VDV204 (2 m, 4P-4P) from JVC
VC-VDV206 (2 m, 4P-6P) from JVC
Note 4: When connecting a secondary device directly to your BD-X200, use a Category 5, cross-wired Ethernet cable.
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Turning the Power On & Off
Inserting & Removing Discs
Disc tray
OPERATE indicator
BUSY
BUSY
OPERATE
OPEN/CLOSE
OPERATE
OPEN/CLOSE
OPEN/CLOSE indicator
OPEN/CLOSE button
OPERATE button
OPTION DV Y/C LINE
SET UP
OPTION DV Y/C LINE
SET UP
DVD RECORDER BD-X200
CHAPTER
DVD RECORDER BD-X200
TITLE
AUDIO
CH1
AUDIO
CH1
TITLE
CHAPTER
DOLBY DIGITAL
LPCMMPEG
DOLBY DIGITAL
LPCMMPEG
CH2
CH2
SET
SET
TOP
PHONES
REV
STOP
PLAY
FWD
PAUSE
REC
TOP
PHONES
REV
STOP
PLAY
FWD
PAUSE
REC
MENU
MENU
MENU
MENU
Turning the Power On
Turning the Power Off
Inserting a Disc
Removing a Disc
Ⅵ While in Operate Off mode (i.e., the OPERATE indicator
is lit up in red), press the OPERATE button.
● The power will turn on, the color of the OPERATE indicator
will change to green, and the DVD recorder will become
ready for use. (Operate On mode)
Ⅵ Stop the DVD recorder.
(It is recommended that you eject the disc at this time.)
Ⅵ Press the OPERATE button to activate Operate On mode.
Ⅵ Stop the DVD recorder.
1. Press the OPEN/CLOSE button.
● The disc tray will open automatically.
While the disc tray is open, the OPEN/CLOSE indicator
will be lit up.
1. Press the OPEN/CLOSE button.
● The disc tray will open automatically.
While the disc tray is open, the OPEN/CLOSE indicator
will be lit up.
1. Press the OPERATE button.
● The DVD recorder will adopt Operate Off mode and the
color of the OPERATE indicator will change to red.
● If the current disc has not been finalized, the message
“NOT FINALIZE” will appear on both the monitor and LCD
display.
Note
2. If the DVD recorder will not be used for an extended
period of time, disconnect the AC adaptor.
● Before disconnecting the AC adaptor, be sure to remove
the power cord from the electrical outlet.
2. Place the disc on the disc tray.
Ensure that the disc is inserted correctly into the tray’s recess
with the printed side facing upward.
● Carefully place the disc in the tray so as not to hit the front
panel.
A period of 45 seconds may pass before the DVD recorder
adopts Operate On mode as it prepares for operation.
2. Remove the disc from the disc tray.
Be sure to wait until the disc tray has opened fully before
removing the disc.
Notes
3. Press the OPEN/CLOSE button.
● Pressing the OPERATE button will have no effect in
Recording mode or Recording Pause mode.
● Pressing this button also has no effect during finalizing,
erasing, and dubbing.
● The disc tray will close automatically.
Notes
● If the DVD recorder is in either Recording mode or
Recording Pause mode, the disc tray will not open when
the OPEN/CLOSE button is pressed.
● Pressing this button also has no effect during finalizing,
erasing, and dubbing.
3. Press the OPEN/CLOSE button.
● The disc tray will close automatically.
Note
Precautions regarding the disc tray
● Do not push the disc tray as it is opening or closing.
● Do not place objects other than discs on the disc tray.
● Do not press down on the disc tray.
When a disc is inserted, information about that disc is
displayed on-screen. (☞ Page 18)
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Using a Keyboard & Mouse
Setting & Displaying the Date & Time
Menu settings, the title and chapter settings, and other DVD recorder settings are carried out from setting screens displayed on the
TV or monitor. In addition, recording operations can also be carried out from similar screens.
Although the DVD recorder’s buttons are used in setting and operation screens, a keyboard and mouse can be used as an alternative.
Use the following procedure to set the internal clock’s date and time. Even when the DVD recorder’s power is turned off, the clock’s
date and time settings are stored using the internal battery.
Note that these settings are used to write the current date and time to a disc being finalized.
The DISPLAY screen can be used to indicate whether or not the date and time are to be displayed on-screen.
Ⅵ Connections
Connect a USB keyboard and mouse to the two USB
VIDEO
LINE
AUDIO
IN
IN
OUT
INPUT
LEVEL
CH1
OUT
terminals on the back of the DVD recorder.
Recommended manufacturers: Logitech
4dB
8dB
BUSY
Y/C
IN
OPERATE
OPEN/CLOSE
CH2
REMOTE
DV IN/OUT
US
LAN
SIGNAL
GND
DC 19V
OPTION DV Y/C LINE
SET UP
DVD RECORDER BD-X200
TITLE
6 button
AUDIO
CHAPTER
CH1
CH2
DOLBY DIGITAL
LPCMMPEG
SET UP button
USB terminals
SET
t button
TOP
PHONES
REV
STOP
PLAY
FWD
PAUSE
REC
MENU
MENU
SET button
Print
Pause
Break
Scroll
Lock
Esc
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
Screen
Sysrq
8 button
7 button
！
1
#
3
$
4
%
5
&
6
(
8
)
9
～
0
=
-
”
'
7
Back
Page
Up
Num
Lock
Insert
Home
End
/
Space
-
2
^
￥
」
*
9
Q
W
E
R
T
Y
U
I
O
P
｀
「
]
7
4
1
0
8
Page
Tab
Enter
Delete
Down
[
@
+
Caps Lock
＋
＊
A
S
D
F
G
H
J
K
L
5
2
6
;
:
Z
X
C
V
B
N
M
<
,
、
>
。
?
/
・
＿
Shift
Shift
.
/
Enter
.
Ctrl
Alt
Alt
Ctrl
Setup Menu
Setting the Date and Time
DISC MENU
INPUT SELECT
SYSTEM
Ⅵ Procedure
Setting of the date and time is carried out using the CLOCK ADJUST MENU
screen. During this procedure, the monitor connected to the VIDEO LINE OUT
terminal is used to monitor the setting of data.
The following functions can be controlled using the keyboard and mouse.
PRESET STYLE
RECORDER
REMOTE
DISPLAY
Ⅵ Turn on the power and ensure that the DVD recorder is stopped.
Function
Front panel Keyboard
Mouse
CLOCK ADJUST
DUBBING
1. Press the SET UP button to display the Setup Menu.
NETWORK
Selection of menu t button
† key
© key
∞ key
√ key
Move the mouse.
And then left
click.
Note
EXIT
items or setting
values
8 button
6 button
7 button
Unless otherwise specified, this user’s manual
describes procedures carried out from the DVD
recorder itself.
2. Open the CLOCK ADJUST MENU screen.
q Use the 6 and 7 buttons to select CLOCK ADJUST. (The currently
selected menu item is displayed as highlighted.)
CLOCK ADJUST MENU screen
Confirmation of
settings
SET button Enter key
Left click.
w Press the SET button to open the CLOCK ADJUST MENU screen.
CLOCK ADJUST MENU
MENU
04/05/04
10:00
DATE
TIME
3. Set the date and time as required.
q Use the 6 and 7 buttons to select either DATE or TIME. Then press the
SET button.
The entry of names and comments for the title and chapter menus is carried out using the keyboard. (Set KEYBOARD STYLE from
the SYSTEM MENU screen in accordance with the keyboard’s input language.)
w Use the tand 8buttons to select the digit to be changed.(The currently
selected digit is displayed as highlighted text.)
e Use the 6 and 7 buttons to change the value of the selected digit.
r Repeat steps w through e to make all of the required settings, and then
press the SET button.
Note
CLOCK ADJUST MENU
It is not possible to set the time in units of seconds. After setting the
minutes, press the SET button in sync with a time signal.
MENU
DATE
TIME
04/05/04
12:00
4. After completing all of the required settings, return to the Setup
Menu.
To do this, use the 6 or 7 buttons to select MENU and then press the SET
button.
5. Return to the normal screen display.
● To do this, press the SET UP button
or
CLOCK SETTING
● Select EXIT from the Setup Menu and press the SET button.
07
07
:
44
44
SET
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Settings & Controls for Recording
Setting & Displaying the Date & Time (continued)
Displaying the Date and Time
DVD Recording
DVD recording is carried out using the following procedure.
Pre-Recording Settings
Preparation of the DVD-R or DVD- ● Insert a new DVD-R or DVD-RW (video mode), or alternatively, a similar disc that has
Use the DISPLAY MENU screen to indicate whether or not the date and time are
to be displayed on-screen and to set a display style. (੬ Page 74 for details
regarding setting methods.)
DISPLAY MENU screen
RW (video mode only).
been recorded on using the DVD recorder.
● If the recording on a DVD-RW is to be performed once again from the beginning, erase
the disc’s data using ERASE from the DISC MENU screen. (☞ Page 30)
DISPLAY MENU
MENU
DISPLAY MENU Screen Makeup
Ⅵ DISPLAY: This parameter is used to indicate whether or not data is to
DISPLAY
ON
ON
TITLE/CHAPTER
RECORDER MODE
TIME/DATE
REMAIN
Use the setting screens to select the appropriate recording signal, setup the recording
conditions, and make other necessary settings. (☞ Page 31)
On-screen settings
ON
be displayed on-screen.
Data will be displayed on-screen. The following parameters can be
used to indicate which data is to be displayed.
TIME+DATE
ON
ON
:
Adjustment of audio recording levels. Audio recording levels can be adjusted in one of two different ways. (☞ Page 35)
Selection of styles for the title and The title and chapter menus are used during playback of a disc to select the section of
MM/DD/YY
DATE STYLE
OFF : No data is displayed on-screen.
(DD/MM/YY:
E-model)
Ⅵ TIME/DATE: This parameter is used to set the way in which the date
chapter menus
the disc to be viewed. A total of five different display styles have been made available for
these menus, and these can be selected using the PRESET STYLE MENU screen. In
addition, the DVD recorder also allows you to freely modify these display styles.
(☞ Page 37)
and time are displayed.
OFF
TIME
DATE
:
:
:
Neither date or time are displayed.
Only the time is displayed.
Only the date is displayed.
TIME + DATE : Both date or time are displayed.
Ⅵ DATE STYLE: This parameter is used to select the way in which the
date is to be displayed.
Recording Operations (☞ Page 38)
YY/MM/DD : Year, month, day
MM/DD/YY : Month, day, year
DD/MM/YY : Day, month, year
● The section between the start of recording using the REC and PLAY buttons
and the end of recording using the STOP button constitutes a single recording
title, and each title is assigned a unique number.
Start of
recording
Chapter 1
(chapter mark)
A single disc can contain up to 99 different titles.
● Each title can be separated into a number of different chapters by inserting
chapter marks at the appropriate points. Unique numbers are also assigned
to chapters, and a single title can contain up to 99 different chapters.
● Adding chapters
Chapter 2
Title 1
To display date and time information on-screen;
A chapter mark is inserted automatically whenever recording is paused.
In addition, CHAPTER CREATION from the RECORDER MENU (1/2) screen
can also be used to setup the automatic or manual insertion of chapter marks.
● Thumbnails (i.e., the frame at the start of recording) and backgrounds are
automatically created for the title and chapter menus using the style selected
using PRESET STYLE.
If EDIT MENU from the SYSTEM MENU screen is set to ENABLE before the
start of recording, it will be possible to modify the chapter menu’s style and
thumbnails and to insert chapter names and comments whenever recording
is stopped (i.e., whenever title closing is performed).
● Once title closing has been carried out, it will not be possible to modify the
chapter menu.
● The REC CONTROL panel can be used to perform recording operations with
a keyboard and mouse. (REC CONTROL from the REMOTE MENU screen
must be set to ON.)
Chapter 3
● Set DISPLAY to ON.
● Set TIME/DATE to anything other than OFF.
Date and time information is displayed as follows.
On-screen display
000 min
Chapter 4
End of
recording
(Title closing)
Mode
Recording or Stop The value of the internal clock
Playback The date and time at which the current disc was
Displayed information
Start of
recording
Chapter 1
finalized.
Title 2
REC
04/05/04
11:20:00
TITLE 1 0:11:22
CHAPTER
Chapter 2
1
0:11:22
End of
recording
TIME/DATE
(Title closing)
● If EDIT MENU from the SYSTEM MENU screen is set to ENABLE, it will be
possible to modify the title menu’s style and to input title names when the disc
is being finalized.
Start of
recording
Title 3
End of
recording
(Title closing)
Processing After Recording (☞ Page 42)
If additional recording is to be If the disc is to be played on this DVD recorder or on a different DVD player:
performed:
Finalize the disc.
Press the OPEN/CLOSE button and To do this, select FINALIZE from the DISC MENU screen.
remove the disc.
*
When a disc has been finalized, it will not be possible to record more content to it or to
modify its menu styles.
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings & Controls for Recording
Preparing a Disc for Recording
Pre-Recording Settings
ⅥThis DVD recorder is capable of recording to DVD-R and DVD-RW (in video mode).
• ENCODE QUALITY
This parameter is used to manually set the bit rate for video
data.
• AUDIO ENCODE
This parameter is used to set the format for encoding (or
compressing) audio data.
Ⅵ Recorder switch settings
DVD-R
DVD-RW
:
:
Only discs that conform with DVD-R Standard 2.0 (video mode) can be used.
Discs of Version 1.1 or later can be used.
Use the AUDIO INPUT LEVEL switch on the DVD recorder’s
rear panel to select the reference input level for analog audio
(i.e., +4 dB or –8 dB).
Although Version 1.1 of DVD-RW standards allows the selection of video mode and VR mode for recording, this
DVD recorder performs recording in video mode only.
*
Version 1.0 of the DVD-RW standards does not support video-mode recording, and for this reason, the corresponding
discs cannot be used.
ⅥThe following screens are used to make settings relevant to
recording.
(Screen setting methods: ☞ Page 75)
ⅥIn terms of recording characteristics, DVD-R and DVD-RW (video mode) differ as follows.
For more details regarding the encoding of audio and video,
refer to pages 33, 34.
DVD-R
DVD-RW (video mode)
:
:
Each disc can be recorded only once. Erasing of data and re-recording are not possible.
After viewing a disc, all data can be erased and it can be used to record new content.
● INPUT SELECT MENU screen
This screen is used to select the audio and video signals to
be used.
The condition of the disc being used will dictate the available recording options as follows.
• ASPECT
This parameter is used to set the aspect for recorded video.
(AUTO, 4:3, LETTER BOX, or SQUEEZE)
For more details, refer to page 32.
Disc condition Recording operations
Blank disc
DVD-R
New content can be recorded. A new title is created and recording
starts from that title’s first chapter.
● SYSTEM MENU screen
RECORDER MENU (2/2) screen
• Y/C TERMINAL MODE
• SET UP (U-model only)
This parameter is set when an analog video signal (i.e.,
composite orYC separate) is being input to the DVD recorder.
Specifically, a setting is made to reflect whether or not the
input signal is a setup signal. SETUP should be set to ON if
it is a setup signal, or to OFF if it is not.
A disc recorded on using this DVD recorder
but not yet finalized.
A new title is created in the unused section of the disc, and recording
starts from that title’s first chapter.
This parameter indicates whether the Y/C IN terminal’s
specification is S1 or S2.(Specifically, it selects the recording
method for the wide-screen discrimination signal.)
• THUMBNAIL FORM
This parameter selects the method to be used for thumbnail
conversion when recording a wide-screen signal.
• AUDIO CHANNEL (DV)
This parameter is to be set when recording an audio signal
from the DV IN/OUT terminal.
Specifically, it indicates whether the signals from channels 1
and 2 or from channels 3 and 4 are to be recorded.
• AUDIO REC VOLUME MODE
This parameter is used to select the method for adjustment
of audio recording levels. Specifically, both channels can be
adjusted while maintaining the same level (BOTH), or each
channel can be adjusted independently (INDEPENDENCE).
For more details regarding methods for the adjustment of
audio recording levels, refer to page 35.
Blank disc
DVD-RW
New content can be recorded. A new title is created and recording
starts from that title’s first chapter.
• TEST SIGNAL
A disc recorded on using this DVD recorder
but not yet finalized.
A new title is created in the unused section of the disc, and recording
starts from that title’s first chapter.
Set this parameter to ON when the color bar output by the
DVD recorder’s internal signal generator is to be recorded.
• EDIT MENU
This parameter indicates whether or not a screen for menu
editing is to be displayed during title closing and finalizing.
A recorded disc from which data is to be
erased.
Erase the recorded data (as described below), and then record
new content.
ENABLE
:
The menu editing screen is to be displayed.
During title closing, this screen can be used to
modify the chapter menu’s style and thumbnails
and also to insert chapter names. (☞ Page 47)
During finalizing, the menu editing screen allows
the title menu’s display style to be modified. (☞
Page 53)
Notes
● If data has been erased from a disc using a different DVD recorder, it may not be possible to record new content to it using
this recorder. To avoid this type of situation, ensure that this DVD recorder is used to erase recorded data.
● New content cannot be recorded to discs that have been finalized.
● Regardless of whether or not finalization has been carried out, it will not be possible to use this DVD recorder to record new
content to a DVD-R or DVD-RW that has been recorded on using other devices.
DISABLE : The menu editing screen is not to be displayed.
In this case, the chapter menu is created using
preset values as part of title closing when
recording is ended.
• DISC IN ACTION
This parameter’s setting is used during the recording of discs
to indicate the action to be taken when a completed (i.e.,
finalized) disc is inserted into this DVD recorder or a different
DVD player.
Erasing All Data From a Disc
● PRESET STYLE MENU screen
DISC MENU screen
MENU : The title menu is displayed.
1. Insert the DVD-RW from which data is to be erased.
This screen is used to select the arrangement and background
style for thumbnails displayed on the tops menu. This DVD
recorder can store eight individual style type (i.e., TYPE1
throughTYPE8), and the most suitable type should be selected
here.
TITLE
:
Playback of the main content begins.
DISC MENU
• TITLE END
2. Press the SET UP button to display the Setup Menu.
This parameter’s setting is used during the recording of discs
to indicate the action to be taken when playback of a title on
a completed disc has ended.
MENU
CANCEL
FINALIZE
3. Use the 7 and 6 buttons to select DISC MENU and then press
DISC ERASE
EXECUTE
the SET button.
For more details, refer to page 37.
MENU
:
The title menu is displayed.
● The DISC MENU screen will appear.
REPEAT : Play back from the top of the title begins.
● RECORDER MENU screen
The RECORDER MENU screen contains two different pages
of parameters.
RECORDER MENU (1/2) screen
• CHAPTER CREATION
This parameter indicates whether chapters are to be created
automatically or manually.
MANUAL : Chapters will be created manually. To create a
chapter, press the REC button while recording.
4. Use the 7 and 6 buttons to select DISC ERASE and then press
the SET button.
● REMOTE MENU screen
• REMOTE SELECT
● A list of setting values will appear.
This parameter should be set to OFF when not controlling
the DVD recorder via the RS-422A REMOTE terminal or the
DV IN/OUT terminal.
Alternatively, the REMOTE CONTROL screen can be
displayed by setting this to 9PIN (MASTER), DV (MASTER),
or DV (SLAVE). (☞ Page 60)
5. Use the 7 and 6 buttons to select EXECUTE from the list and
then press the SET button.
● The erasing of data will begin.
The message“DISC ERASE”appears and the state of progress is displayed
using a progress bar.
● When all data has been erased, the progress bar will disappear.
AUTO
:
Chapters are to be created automatically.In this
case, the DVD recorder will create chapters at
the time intervals set using SET INTERVAL.
• REC CONTROL
This parameter indicates whether or not the REC CONTROL
panel is to be displayed constantly on-screen when a
recordable disc has been inserted.
DISC ERASE
• TOTAL CONTENT TIME
This parameter is used to make a setting relevant to the
encoding (or compression) of video data.
A setting should be made here when the DVD recorder is to
automatically set the bit rate based on the recording time
and the remaining disc capacity. Specifically, this parameter
sets the recording time.
CAUTION
Set this to ON when using a keyboard and/or mouse.
● All of the data recorded to the disc will be erased in this process. Before
starting, therefore, confirm that no important data is stored on this disc.
● Under no circumstances should the power be turned off or the power cord
disconnected while data is being erased.
30
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings & Controls for Recording
Selecting & Confirming Input Signals
Setting the Encoding Format for Audio & Video
The selection of audio and video input signals is carried out from the INPUT SELECT MENU screen as described below. In
addition, the type of input signals that have been selected can be confirmed on the front panel.
The setting of encoding formats for audio and video is carried out from the RECORDER MENU (1/2) screen as described below.
Video input indicators
BUSY
Selecting Input Signals
Setting Encoding Formats
OPEN/CLOSE
BUSY
OPEN/CLOSE
ⅥStop the DVD recorder.
ⅥStop the DVD recorder.
OPTION DV Y/C LINE
SET UP
1. Open the INPUT SELECT MENU screen.
1. Open the RECORDER MENU (1/2) screen.
OPTION DV Y/C LINE
SET UP button
q Press the SET UP button to display the Setup Menu.
w Select INPUT SELECT using the 6 and 7 buttons and then press the
SET button.
SET UP
q Press the SET UP button to display the Setup Menu.
SET
TOP
MENU
SET UP button
SET button
MENU
w Select RECORDER using the 6 and 7 buttons and then press the SET
button.
SET
TOP
MENU
MENU
SET button
2. Make the required settings on the INPUT SELECT MENU screen.
q Select the parameter to be set using the 6 and 7 buttons, and then
press the SET button to display a list of possible settings.
w Select the required setting using the 6 and 7 buttons, and then press
the SET button to adopt this setting.
2. Make the required settings on the RECORDER MENU (1/2)
RECORDER MENU (1/2) screen
screen.
INPUT SELECT MENU screen
q Select the parameter to be set using the 6 and 7 buttons, and then
press the SET button to display a list of possible settings.
w Select the required setting using the 6 and 7 buttons, and then press
the SET button to adopt it.
RECORDER MENU (1/2)
MENU
INPUT SELECT MENU
MANUAL
CHAPTER CREATION
SET INTERVAL
MENU
Every05Min
INPUT SELECT
LINE
TOTAL CONTENTS TIME
ENCODE QUALITY (Mbps)
AUDIO ENCODE
NO USE
4.4
3. Complete the setting process.
LPCM
AUTO
To do so, carry out one of the following procedures.
3. Complete the setting process.
ASPECT
•
•
Select MENU and press the SET button to return to the Setup Menu.
Press the SET UP button to return to the normal screen display.
To do so, carry out one of the following procedures.
•
•
Select MENU and press the SET button to return to the Setup Menu.
Press the SET UP button to return to the normal screen display.
Item
Description
Video Encoding
INPUT SELECT
This parameter is used to select the audio and video input signals.
LINE
Y/C
DV
:
:
:
The composite video signal from the VIDEO LINE IN terminal and the analog audio signals
from the AUDIO IN terminals are to be used.
The YC separate signal from the Y/C IN terminal and the analog audio signals from the
AUDIO IN terminals are to be used.
The audio and video signals from the DV IN/OUT terminal are to be used.
Item
Description
TOTAL CONTENTS TIME
If you already know the duration of the video to be recorded, this parameter can be set to the
corresponding time to allow your BD-X200 to select the optimum encoding bit rate.(Make a setting
in hours and minutes.)
● If the recording time is set using this parameter, ENCODE QUALITY will be set automatically,
and this setting may not be modified manually.
● If this function is not to be used, set it to NO USE.
Note
Setting of INPUT SELECT will not be possible when REMOTE SELECT from the REMOTE MENU screen has been set to
DV(MASTER), DV(SLAVE), or DV(TRIGGER).
When this setting is made, ENCODE QUALITY will be returned to its previous setting.
DV signals will be used for input at these times.
ENCODE QUALITY (Mbps) This parameter can be set when TOTAL CONTENTS TIME has been set to NO USE.
Specifically, it allows direct setting of the encoding bit rate (i.e., the amount of data per second).
Large values increase the quality of the video; however, this also increases the overall data size.
Setting range:
The range of values that can be set depends on the audio encoding format.
Confirming Input Signals
LPCM
:
4.0 to 7.8 Mbps (in 0.2 Mbps steps)
DOLBY DIGITAL: 2.0 to 9.0 Mbps (in 0.2 Mbps steps)
ⅥThe type of video signals that have been selected for input can be confirmed
using the video input signal indicators on the DVD recorder’s front panel.
Specifically, the indicator corresponding to the type of input signal selected
OPTION DV Y/C LINE
using INPUT SELECT will be lit up or flashing.
Lit
:
The selected signal is being received.
Flashing : The selected signal is not being received.
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
U
E
Settings & Controls for Recording
Settings & Controls for Recording
Setting the Encoding Format for Audio & Video (continued)
Audio Encoding
Setting the Encoding Format for Audio & Video (continued)
Audio Encoding
ⅥAUDIO ENCODE
This parameter is used to set the encoding format for audio data.
ⅥAUDIO ENCODE
This parameter is used to set the encoding format for audio data.
LPCM
DOLBY DIGITAL : Dolby AC3 encoding.
MPEG MPEG encoding.
LPCM
:
Linear PCM encoding
:
Linear PCM encoding
DOLBY DIGITAL: Dolby AC3 encoding.
:
Note
If the SET UP button is pressed while in Recording mode, the video bit-rate setting and audio encoding format will be
displayed on-screen. Press the SET UP button once again to hide this information.
Note
If the SET UP button is pressed while in Recording mode, the video bit-rate setting and audio encoding format will be
displayed on-screen. Press the SET UP button once again to hide this information.
Guide to Recording Times
Guide to Recording Times
The time available for recording on a disc will depend on the video encoding bit rate and audio encoding format that have been set.
Furthermore, the more titles a disc contains, the less time will be available for recording. Use the following table as a guide to the
amount of time available for recording.
The time available for recording on a disc will depend on the video encoding bit rate and audio encoding format that have been set.
Furthermore, the more titles a disc contains, the less time will be available for recording. Use the following table as a guide to the
amount of time available for recording.
Encoding bit rate
Encoding bit rate
Audio encoding format
Audio encoding format
9 Mbps
61 min.
—
8 Mbps
68 min.
—
7 Mbps
77 min.
67 min.
6 Mbps
88 min.
76 min.
5 Mbps
103 min.
87 min.
4 Mbps
125 min.
102 min.
3 Mbps
157 min.
—
2 Mbps
212 min.
—
9 Mbps
62 min.
63 min.
—
8 Mbps
69 min.
70 min.
—
7 Mbps
78 min.
79 min.
68 min.
6 Mbps
89 min.
91 min.
77 min.
5 Mbps
105 min.
108 min.
88 min.
4 Mbps
126 min.
131 min.
103 min.
3 Mbps
161 min.
168 min.
—
2 Mbps
218 min.
231 min.
—
DOLBY DIGITAL
LPCM
DOLBY DIGITAL
MPEG
LPCM
34
E-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings & Controls for Recording
Adjusting of Audio Recording Levels
Checking the Video Input
This DVD recorder’s audio recording levels can be adjusted using two different methods, and AUDIO REC VOLUME MODE from
the RECORDER MENU (2/2) screen indicates the method to be used. In addition, it is also possible to return the audio recording
levels to their default settings (i.e., unity gain).
Use the monitor connected to the VIDEO LINE OUT terminal to confirm that the input video signal is as required.
The following procedure will allow you to monitor the quality at which the video will be recorded to a DVD.
Note: The AUDIO INPUT LEVEL switch on the DVD recorder’s rear panel can be used to select the reference input level for analog
VIDEO LINE OUT terminal
audio (i.e., +4 dB or –8 dB).
VIDEO
LINE
AUDIO
IN
IN
OUT
INPUT
LEVEL
CH1
OUT
4dB
8dB
Selecting the Adjustment Method
Y/C
IN
2
RECORDER MENU (2/2) screen
1. Open the RECORDER MENU (2/2) screen.
DV IN/OUT
To do this, select † button from the RECORDER MENU (1/2) screen and
USB
LAN
SIGNAL
GND
RECORDER MENU (2/2)
press the SET button.
BACK
Monitor screen
Y/C TERMINAL MODE
THUMBNAIL FORM
S1
NORMAL
2. Make the required setting using AUDIO REC VOLUME MODE
from the RECORDER MENU (2/2) screen.
1,2ch † 1,2ch
BOTH
AUDIO CHANNEL (DV)
AUDIO REC VOLUME MODE
DISC IN ACTION
BOTH
:
Audio levels are adjusted while both the CH1/CH2
are maintained at the same volume.
MENU
TITLE END
MENU
Signal Connections
INDEPENDENCE
:
The CH1/CH2 are adjusted separately.
Connect the VIDEO LINE OUT terminal to the monitor.
BUSY
OPEN/CLOSE
Procedure
Adjusting the Audio Recording Levels
OPTION DV Y/C LINE
SET UP
DVD RECORDER BD-X200
TITLE
Ⅵ Press and hold the REC button for at least 2 seconds while the DVD
recorder is stopped or inserted with no disc. While this button is being
held, input signal encoded/decoded in MPEG will be output via the VIDEO
OUT terminal on the rear panel.
CHAPTER
DOLBY DIGITAL
LPCMMPEG
SET
TOP
REV
STOP
PLAY
FWD
PAUSE
REC
BUSY
MENU
MENU
OPERATE
OPEN/CLOSE
● This function allows the quality of the video to be confirmed before recording
to a DVD.
OPTION DV Y/C LINE
SET UP
DVD RECORDER BD-X200
TITLE
AUDIO
REC button
CHAPTER
CH1
DOLBY DIGITAL
LPCMMPEG
Audio level indicator
CH2
Note
SET
Buttons used
MENU
TOP
PHONES
REV
STOP
PLAY
FWD
PAUSE
REC
MENU
Audio will be muted at this time.
The bit-rate setting value is
indicated on the LCD display.
ⅥReturn from setting screens to the normal display.
ⅥRecording levels can be adjusted in either Stop or Recording mode. Be sure to monitor the front panel’s audio level indicator as
the levels are being adjusted. Adjust the level so that the LED on the far right does not light.
ENCODING XX
Bit-rate value
Adjusting both channels together (BOTH)
ⅥTo raise the recording level
Adjusting both channels separately (INDEPENDENCE)
ⅥTo adjust the Channel 1 level
Press the 6 button while holding the 8 or
tbutton to raise the audio recording levels
Press either the 6 or 7 button while
holding the 8 button.
SET
SET
for Channel
simultaneously.
1
and Channel
2
Pressing the 6 button raises the recording
level.
Pressing the 7button lowers the recording
level.
ⅥTo lower the recording level
ⅥTo adjust the Channel 2 level
Press the 7 button while holding the 8 or
tbutton to lower the audio recording levels
Press either the 6 or 7 button while
holding the t button.
SET
SET
for Channel
simultaneously.
1
and Channel
2
Pressing the 6 button raises the recording
level.
Pressing the 7button lowers the recording
level.
Returning Audio Recording Levels to Default Settings (UNITY MODE)
ⅥPress and hold the 8 and t buttons simultaneously to return the audio recording levels to their default settings (i.e., unity gain).
● Both of the audio recording levels will be fixed at the default setting.
35
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Selecting Styles for Title & Chapter Menu
Recording Sequence
Each recorded DVD contains title and chapter menus that provide information relating to its titles and chapters.
Whenever recording is carried out, title numbers, chapter numbers, and thumbnails are automatically generated in order to create
the title and chapter menus.
Specifically, the frames from the start of individual recordings are used as thumbnails for the title menu.
In a similar way, the frames at which chapter marks have been inserted are used as thumbnails for chapter menus.(These thumbnails
may be modified later on.) The title menu will become the top thumbnail of the chapter menu.
Use the following sequence as a reference when performing recording.
● Input settings: ☞ Page 32.
● Video and audio quality settings: ☞ Pages 33, 34.
● Navigation settings (i.e., DISC IN ACTION and TITLE END): ☞ Page 81
The term “style” is used to refer to a combination of thumbnail characteristics for the title and chapter menus.This DVD recorder can
store eight different style types, and the PRESET STYLE MENU screen is used to indicate which of these types is to be used.
REC button + PLAY button
Start of recording
Making Settings in the PRESET STYLE MENU screen
Chapter 1
Chapter 2
Setup Menu
1. Press the SET UP button to display the Setup Menu.
REC button
REC button
DISC MENU
2. Select PRESET STYLE from the Setup Menu and then press the
INPUT SELECT
SET button.
SYSTEM
● The PRESET STYLE MENU screen will appear. Within this screen, the
PRESET STYLE
RECORDER
STYLE parameter indicates the style type currently selected for the title and
chapter menus.
REMOTE
DISPLAY
CLOCK ADJUST
3. Confirm the settings for the currently selected style.
DUBBING
NETWORK
Chapter 3
Select STYLE and then press the SET button to display the corresponding
EXIT
STYLE screen.
TITLE PATTERN
:
The display pattern currently selected for the title
menu. Each display pattern uses different numbers,
positions, and sizes for thumbnails, in addition to
different backgrounds.
PAUSE button
Recording Pause
PRESET STYLE MENU screen
PRESET STYLE MENU
CHAPTER PATTERN : The display pattern currently selected for chapter
menus. Each display pattern uses different numbers,
positions, and sizes for thumbnails, in addition to
different backgrounds.
PLAY button or PAUSE button
MENU
TYPE1
STYLE
Resumption of recording
1
TITLE PATTERN
CHAPTER PATTERN
1
Chapter 4
4. Use the cursor buttons (6, 7, t, and 8) to select one of the
eight style types and display the corresponding STYLE screen.
PAUSE button
Recording Pause
5. To use a specific style, select the corresponding type number
and then press the SET button.
This type number will then be stored by the DVD recorder.
Following this, the screen’s BACK button will be highlighted. The SET button
can now be pressed to return to the PRESET STYLE MENU screen.
Type number
STOP button
STYLE screen
Ⅵ
If BACK is used to exit the STYLE screen without the SET button
being pressed for the newly selected type, the style setting will
not be updated.
End of recording
Processing time:
30 seconds maximum
STYLE
BACK
1
Chapter menu modification possible*
CHAPTER PATTERN
TITLE PATTERN
Notes
● The STYLE settings for chapter menus can be freely modified until title closing
is carried out. (☞ Page 47)
● The STYLE settings for the title menu can be freely modified until the DVD is
finalized. (☞ Page 53)
● Each style can be freely modified and stored in the DVD recorder’s memory.
In addition, it is also possible to freely select and modify display patterns
(i.e., the number, position, and size of thumbnails in addition to the
background). For more details regarding modification of PRESET STYLE,
refer to page 43.
● In certain cases, the frames used for chapter menu thumbnails may differ
slightly from the exact frames at which the corresponding chapter marks
were inserted.
Title closing
Recording of a new title
Processing time:
several seconds ~ several minutes
1
1
Title menu modification possible*
TYPE3
TYPE7
TYPE4
TYPE8
TYPE1
TYPE5
TYPE2
TYPE6
Style types
Finalizing
Processing time:
20 minutes maximum
Playback possible
* Title and chapter menu modification will be possible when EDIT MENU from the SYSTEM MENU screen has been set to
ENABLE.
* Playback will not be possible until a disc has been finalized.
37
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Recording with the Front Panel
Recording with the Front Panel (continued)
BD-X200 recording operations can be carried out in two different ways — namely, using the buttons provided on the front panel and
using the on-screen REC CONTROL panel.In the latter case, furthermore, recording operations can be performed using a keyboard
and mouse. The following section, however, will provide a description of recording using the front panel buttons.
On a DVD, the section of video recorded between the start of recording and pressing of the STOP button to end recording is stored
as a single title, and a unique title number is assigned to each of these sections. A single disc can contain up to 99 different titles.
In addition, each title can be separated into a number of different chapters by inserting chapter marks at the appropriate points, and
each title can contain up to 99 chapters.
Information relating to titles and chapters is stored on a disc in the form of title and chapter menus. When the disc is being played,
therefore, the title and chapter menus can be used to access specific sections of stored video and audio.
LCD display
6. End recording and remove the disc.
Note
Depending on how the disc will be used, one of two different procedures is
implemented at this time.
When recording is stopped or a title is
closed, the state of progress will be
indicated on-screen using a progress bar.
● If more content will be recorded to the disc using this DVD recorder:
Simply press the OPEN/CLOSE button and remove the disc. (Do not finalize
the disc before it is removed.)
● If the disc is to be played on this DVD recorder or on a different DVD
player:
Recording stopped
REC STOP
Title closing
TITLE CLOSE
Finalize the disc, press the OPEN/CLOSE button, and then remove the disc.
For more details regarding finalizing, refer to page 42.
BUSY
Progress bar
OPERATE
OPEN/CLOSE
OPEN/CLOSE button
OPTION DV Y/C LINE
SET UP
DVD RECORDER BD-X200
CHAPTER
AUDIO
TITLE
CH1
CH2
DOLBY DIGITAL
LPCMMPEG
Inserting Chapter Marks Manually or Automatically
SET
TOP
PHONES
REV
STOP
PLAY
FWD
PAUSE
REC
MENU
MENU
RECORDER MENU (1/2) screen
In addition to pausing the recording, a number of different manual and automatic
methods can be used to insert chapter marks.
RECORDER MENU (1/2)
The actual method to be used is determined by CHAPTER CREATION and SET
INTERVAL from the RECORDER MENU (1/2) screen.
● If chapter marks are to be inserted manually at any point, set CHAPTER
CREATION to MANUAL.
Chapter marks can then be inserted by pressing the REC button while recording.
● If chapter marks are to be inserted automatically, first of all set CHAPTER
CREATION to AUTO. Then use SET INTERVAL to set a time (in minutes) for
chapter mark insertion.
MENU
STOP button
CHAPTER CREATION
SET INTERVAL
MANUAL
Every05Min
REC button
PAUSE button
TOTAL CONTENTS TIME
ENCODE QUALITY (Mbps)
AUDIO ENCODE
NO USE
4.4
LPCM
Remaining time
ⅥInsert a disc that can be recorded on.
Monitor display
1. With the DVD recorder stopped, make all of the required settings
and adjust the audio recording levels.
The DVD recorder will insert chapter marks at the corresponding intervals during
recording.
000 min
2. Start recording.
Notes
This is done by pressing the REC and PLAY buttons simultaneously.
● The frame at which a chapter mark is inserted will be used for the
corresponding thumbnail in the chapter menu. When EDIT MENU from the
SYSTEM MENU screen is set to ENABLE, the frames used for thumbnails
can be modified on theTHUMBNAIL EDIT screen that appears automatically
at the end of recording.
3. Pause recording.
This is done by pressing the PAUSE button.
● The DVD recorder will adopt Recording Pause mode and a chapter mark will
be inserted at the current position.
A number of different methods can also be used for the manual or automatic
insertion of chapter marks. (☞ Page 40)
REC
04/05/04
11:20:00
TITLE 1 0:11:22
● Each title can contain up to 99 chapters.
CHAPTER
1
0:11:22
● In certain cases, the frames used for chapter menu thumbnails may differ
slightly from the exact frames at which the corresponding chapter marks
were inserted.
Title and chapter numbers
4. Restart recording.
Press the PLAY or PAUSE button.
● Recording will begin once again and a new chapter will be created in the
current title.
Notes
● A maximum of 10 minutes will be
required to complete title closing.
● The remaining time available for
recording on a disc will be displayed
on the monitor. Note that this is to be
used as a general guide, not as an
exact figure. (DISPLAY and REMAIN
from the DISPLAY MENU screen must
both be ON for this figure to be
displayed.)
● During the recording process, the
current title number and chapter
number are displayed on the monitor.
(DISPLAY and TITLE/CHAPTER from
the DISPLAY MENU screen must both
be ON for these numbers to be
displayed.)
5. End recording (i.e., close the title)
Press the STOP button when either recording or paused.
● The action of the DVD recorder following the end of recording depends on
the setting of EDIT MENU from the SYSTEM MENU screen.
DISABLE
:
Recording is ended and the chapter menu is created using
preset settings (i.e., the title is closed).
ENABLE
:
The THUMBNAIL EDIT screen will appear.This screen can be
used to modify the chapter menu’s display style, to change the
thumbnails used, to input chapter names, and to perform other
similar functions. For more details, refer to page 47.
Ⅵ
If additional recording is to be carried out, repeat steps 1 through
5 above.
● In such a case, the subsequent recording is stored as a new title.
39
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Using a Keyboard & Mouse to Control Recording
Finalizing (for playback on this and other DVD players)
BD-X200 recording operations can be carried out using the REC CONTROL panel displayed on the monitor. In addition, a keyboard
and mouse can also be used when working with this panel.
Finalize a disc recorded using this DVD recorder as described below in order to ensure that it can be played on this and other DVD
players. In the case of DVD-RWs, playback will be possible on DVD players that support video mode.
After finalizing a disc;
VIDEO
LINE
AUDIO
IN
IN
OUT
INPUT
LEVEL
CH1
OUT
● No additional recording will be possible.
● The title menu cannot be changed.
● The titles created before finalizing will be displayed as the top menu.
4dB
8dB
Signal Connections
Y/C
IN
CH2
REMOTE
Connect a keyboard and mouse to the USB terminals on the back of the DVD
recorder.
DV IN/OUT
LAN
US
SIGNAL
GND
DC 19V
Settings
Finalizing
● If the REC CONTROL panel is to be displayed on-screen, set REC CONTROL
from the REMOTE MENU screen to ON.
This panel will be displayed in Stop, Recording, and Recording Pause mode.
ⅥTo open the Setup Menu, press the DVD recorder’s SET UP button. It is not
possible to open this screen using the keyboard or mouse.
Print
Pause
Break
Scroll
Lock
Esc
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
Screen
The process of finalizing can be carried out in two different ways.
● Select DISC MENU and then FINALIZE from the Setup Menu.
● Select FINALIZE on the REC CONTROL panel when this is being used for recording.
Sysrq
！
1
”
#
3
$
4
%
5
&
6
'
7
(
8
)
9
～
0
=
-
Back
Page
Up
Num
Lock
Insert
Home
End
/
-
Space
2
^
￥
」
*
9
Q
W
E
R
T
Y
U
I
O
P
｀
「
]
Page
7
4
1
0
8
T
a
b
Enter
Delete
Down
@
[
+
Caps Lock
＋
＊
A
S
D
F
G
H
J
K
L
5
2
6
;
:
Z
X
C
V
B
N
M
<
,
、
>
。
?
/
・
＿
Shift
Shift
.
/
Enter
.
Ctrl
Alt
Alt
Ctrl
Setup Procedure: Insert the disc to be finalized.
Procedure
REMOTE MENU screen
1. If using the Setup Menu:
1. If using the REC CONTROL panel:
REMOTE MENU
1. Start recording.
000 min
q Press the SET UP button to
Select FINALIZE and then press
the keyboard’s Enter key.
DISC MENU
MENU
Keyboard
:
Use the arrow keys (©, †, ∞, and √) to select Record (r)
from the REC CONTROL panel, and then press the Enter key.
Move the mouse pointer to the Record (r) button and left click
while the Record button selected.
display the Setup Menu, and
then select DISC MENU.
MENU
9PIN(MASTER)
REMOTE SELECT
REC CONTROL
REM FF/REW MODE
EXECUTE
CANCEL
FINALIZE
DISC ERASE
*
If operating using a mouse, left
click the FINALIZE button.
ON
Mouse
:
w Set FINALIZE from the DISC
MENU screen to EXECUTE
and then press the SET button.
FF/REW
FINALIZE
FINALIZE button
DISC TITLE
2. Pause recording.
REC
Keyboard
:
Use the arrow keys (©, †, ∞, and √) to select Pause (w) from
the REC CONTROL panel, and then press the Enter key.
Move the mouse pointer to the Pause (w) button and left click
while the Pause button is selected.
04/05/04
11:20:00
TITLE
CHAPTER
1
1
0:11:22
0:11:22
Mouse
:
● The DVD recorder will adopt Recording Pause mode;in addition, a chapter
mark and thumbnail will be inserted at the current position.
The screen that will now be displayed depends on the setting of EDIT MENU from the SYSTEM MENU screen.
000 min
If this is set to DISABLE, a screen seeking confirmation of
finalizing will appear.
In this case, perform finalizing as described below.
If this is set to ENABLE, a screen for editing title menus will
appear. Use this screen to confirm that the title menu is as
required, to modify the display style, and to input title
names. (☞ Page 53)
3. Restart recording.
Keyboard
:
Use the arrow keys (©, †, ∞, and √) to select either Record
(r) or Pause (w) from the REC CONTROL panel, and then
press the Enter key.
FINALIZE
Mouse
:
Move the mouse pointer to the Record (r) or Pause (w) button
and left click while the Record or Pause button is selected.
DISC TITLE
2. Make the appropriate selection in the confirmation screen.
Ⅵ Steps 2 and 3 can be repeated to create a single, partitioned title.
REC
Confirmation screen
q Select YES and then press the SET button to continue finalizing.
4. End recording (i.e., close the title)
04/05/04
11:20:00
TITLE 1 0:11:22
● The finalizing process will begin.
CHAPTER
1
0:11:22
Select Stop (q) from the REC CONTROL panel and press the Enter key.
● The action of the DVD recorder following the end of recording depends on
the setting of EDIT MENU from the SYSTEM MENU screen.
DISABLE : Recording is ended and the chapter menu is created using
standard settings (i.e., the title is closed).
A bar showing the state of progress will be displayed during finalizing.
● The progress bar will disappear when finalization has been completed and
the normal screen display will then be restored.
REC CONTROL panel
Notes
● DISC TITLE from the REC CONTROL
panel can be selected to allow a name
to be input for the disc. This type of
name proves useful when managing
discs using a PC.Note that disc names
are not displayed on the monitor or the
DVD recorder.
(The REC CONTROL panel will not be displayed.)
Ⅵ Select NO from the confirmation screen to cancel finalizing and return to the
previous screen.
FINALIZE
ENABLE
:
The THUMBNAIL EDIT screen will appear. This screen can
be used to modify the chapter menu’s display style, to change
the thumbnails used, to input chapter names, and to perform
other similar functions. For more details, refer to page 47.
YES
NO
Notes
● A maximum of 20 minutes will be required to complete finalizing.
● When finalizing is carried out, all of the disc’s recorded video and audio are
stored in accordance with the DVDVideo Standard;accordingly, this content
can also be replayed as DVD video.
Ⅵ If additional recording is to be carried out, repeat steps 1 through 4
above.
● In such a case, each subsequent recording will be stored as a new title.
Progress screen
Characters allowed for the disc title are
alphanumerical characters and
underscore (_) only. Space and other
symbols may not be used.
● FINALIZE and DISC TITLE from the
REC CONTROL panel cannot be used
while recording.
● The Record (r) button from the REC
CONTROL panel can be activated or
clicked to insert chapter marks and
thumbnails during recording.
5. End recording and remove the disc.
Depending on how the disc will be used, one of two different procedures
is implemented at this time.
● If more content will be recorded to the disc using this DVD recorder:
Simply press the DVD recorder’s OPEN/CLOSE button and remove the
disc. (Do not finalize the disc before it is removed.)
● If the disc is to be played on this DVD recorder or on a different DVD
player:
● Although a disc finalized using this DVD recorder may in principle be played
on other DVD players, there is no guarantee that all of its content will be
playable.
● The action to be taken by this DVD recorder when a finalized disc is inserted
or when playback of a title has ended is specified by DISC IN ACTION and
TITLE END respectively from the RECORDER MENU (2/2) screen.
TITLE END is to be set before recording a title.
FINALIZE
DISC IN ACTION is to be set before finalizing.
Use FINALIZE from the REC CONTROL panel to finalize the disc before it
is ejected.
For more details regarding finalizing, refer to page 42.
41
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Title & Chapter Menu Settings
Title & Chapter Menu Settings
BD-X200 Title & Chapter Menus
Selecting and Changing Styles for Title & Chapter Menus
This DVD recorder can automatically create title and chapter menus in response to recording operations and can save these to the
disc being recorded.
When the disc is subsequently played, these title and chapter menus can be used to access specific sections of stored video and
audio.
Title and chapter menus are used during playback of a DVD to select a title or chapter for viewing.Your BD-X200 provides a total of
eight different styles for displaying title and chapter menus. Use the following procedure during the recording process to select
styles for these menus.
● When recording is stopped using the STOP button or a similar action (i.e., disc closing), a title number and a thumbnail
(corresponding to the frame at the start of recording) will be created to form part of the disc’s title menu. A single disc can contain
up to 99 different titles.
● Similarly, if a chapter mark is inserted during recording, a chapter number and a thumbnail (corresponding to the frame at the
chapter mark) will be created to form part of the title’s chapter menu. Chapter marks are used as targets for skipping during
playback. Each title can contain up to 99 chapters.
Notes
Typical Title Menu
● This DVD recorder can store a total of eight display styles, where each style
is a combination of title and chapter menu display characteristics.
● The title menu can be displayed by pressing the TOP MENU button on the
front panel while in Stop or Playback mode; furthermore, the chapter menu
can then be opened using the MENU button.
Thumbnail
4
5
1
2
Title
number
Background
Start of recording
End of recording Start of recording
Title 2
End of recording
Title 1
3
6
Title menu
Thumbnail
Thumbnail
Chapter mark
Chapter mark
Chapter mark
Confirming or Selecting a Style
Display styles can be selected and modified using the PRESET STYLE MENU
screen.
Recording
Recording
PRESET STYLE MENU screen
1. Press the SET UP button to display the Setup Menu, select PRESET
STYLE, and then press the SET button.
● The PRESET STYLE MENU screen will appear.
PRESET STYLE MENU
MENU
TYPE1
1
STYLE
TITLE PATTERN
CHAPTER PATTERN
2. Confirm the settings for the currently selected style.
The STYLE parameter will display the type number of the style currently
selected.
Thumbnail
Chapter 1
Thumbnail
Chapter 2
Thumbnail
Chapter 3
Thumbnail
Chapter 1
Thumbnail
Chapter 2
1
Chapter menus
ⅥSelect STYLE and then press the SET button to display the corresponding
STYLE screen.
TITLE PATTERN
:
The display pattern currently selected for the title
menu.Each display pattern uses different numbers,
positions, and sizes for thumbnails, in addition to a
different background.
ⅥDisplay Styles
CHAPTER PATTERN : The display pattern currently selected for chapter
menus. Each display pattern uses different
numbers, positions, and sizes for thumbnails, in
addition to a different background.
Type number
A total of eight different display styles can be used with title and chapter menus.The PRESET STYLE MENU screen can be used
to select the type of style to be used in the creation of title and chapter menus.
In addition, each of the display styles can be modified as required. (☞ Page 45)
Depending on the style used and the number of menu items, title and chapter menus may extend over more than one page.
STYLE screen
STYLE
BACK
Notes
3. Use the cursor buttons (6, 7, t, and 8) to select one of the
eight style types and to display the corresponding STYLE screen,
containing both title and chapter patterns.
1
● This DVD recorder can store a total of six different display patterns for title and chapter menus.
At the time of purchase, your BD-X200 will contain five different template files. Any of the stored display patterns can be
selected to change the styles applied to each of the title and chapter menus.
● In addition, original title and chapter menus can also be created using Easy menu a freeware application for editing menu
templates. (☞ Page 46)
CHAPTER PATTERN
TITLE PATTERN
4. To use a specific style, select the corresponding type number
and then press the SET button.
1
1
This type number will then be stored in the DVD recorder’s memory.
Following this, the screen’s BACK button will be highlighted. The SET button
can now be pressed to return to the PRESET STYLE MENU screen.
ⅥModifying Chapter Menus
A chapter menu’s display style and thumbnails can be edited at the end of recording (i.e., during title closing); furthermore, titles
and comments for the chapter menu can also be input at this time. (EDIT MENU from the SYSTEM MENU screen must be set to
TYPE3
TYPE7
TYPE4
TYPE8
TYPE1
TYPE5
TYPE2
TYPE6
ENABLE for this to be possible.)
(☞ Page 47)
ⅥModifying the Title Menu
ⅥIf BACK is used to exit the STYLE screen without the SET button being
pressed for the newly selected type, the style setting will not be updated.
Style types
The style used for the title menu and the text input for the title name may both be modified before finalizing is carried out. (EDIT
MENU from the SYSTEM MENU screen must be set to ENABLE for this to be possible.)
(☞ Page 53)
Notes
● Thumbnail of the title menu will be the top thumbnail of the chapter menu.
● Once a title is closed, it will no longer be possible to modify the chapter menu.
● No modifications whatsoever will be possible when the disc has been finalized.
● When a disc is finalized, its title menu will be used to create the top menu.
● Thumbnail creation method during wide-signal recording can be selected in THUMBNAIL FORM of the RECORDER (2/2)
menu screen.
43
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Title & Chapter Menu Settings
Selecting and Changing Styles for Title & Chapter Menus (continued)
Ending Settings in the PRESET STYLE MENU Screen
Selecting Display Styles
The PRESET STYLE MENU screen can be used to change the styles used for displaying title and chapter menus. One of eight
different types of style can be selected for each of the title and chapter menus.
PRESET STYLE MENU screen
Ⅵ To end settings in the PRESET STYLE MENU screen;
This DVD recorder can also store a total of six different display patterns for title and chapter menus. At the time of purchase, your
BD-X200 will contain five different template files. Any of the stored display patterns can be selected to change the styles applied to
each of the title and chapter menus.
Select MENU and press the SET button to return to the Setup Menu.
PRESET STYLE MENU
MENU
Ⅵ To end menu settings;
Either press the front panel’s SET UP button or select EXIT from the Setup
Menu and then press the SET button.
TYPE1
4
STYLE
TITLE PATTERN
CHAPTER PATTERN
1
PRESET STYLE MENU screen
1. Open the PRESET STYLE MENU screen.
This screen allows patterns to be modified for the style indicated by the STYLE
PRESET STYLE MENU
parameter.
MENU
TITLE PATTERN
:
:
Shows the pattern number for the current title-menu
display style as indicated by the STYLE parameter.
Shows the pattern number for the current chapter-
menu display style as indicated by the STYLE
parameter.
TYPE1
1
STYLE
TITLE PATTERN
CHAPTER PATTERN
1
CHAPTER PATTERN
When the STYLE parameter’s number setting is changed, the patterns
used for title and chapter menus in the new style will be displayed by
TITLE PATTERN and CHAPTER PATTERN respectively.
Easymenu: Freeware for Editing Menu Templates
2. Change the display patterns for the title and chapter menus as
The freeware application Easymenu can be used to create original DVD menus on your PC.
Menu templates created with this application can then be transferred to your BD-X200 using a network cable, thus allowing you to
make imaginative and creative DVDs with the minimum of effort.
Easymenu can be downloaded from the following web page. Please refer to the software manual for details regarding usage and
precautions.
TITLE PATTERN screen
required.
TITLE PATTERN
For example, let’s change the title menu’s display pattern from 1 to 4.
SelectTITLE PATTERN from the PRESET STYLE MENU screen and press
the SET button.
BACK
1
● The TITLE PATTERN screen will appear.
3. Use the cursor buttons (t, 8, 6, and 7) to select the fourth
pattern on the TITLE PATTERN screen, and then press the SET
button.
BUSY
OPERATE
OPEN/CLOSE
● The title menu’s display pattern changes to No. 4, and the BACK button
OPTION DV Y/C LINE
SET UP
DVD RECORDER BD-X200
TITLE
AUDIO
CHAPTER
becomes highlighted.
CH1
CH2
DOLBY DIGITAL
LPCMMPEG
SET
PHONES
REV
STOP
PLA
Y
FWD
PAUSE
REC
TOP
MENU
MENU
4. With the BACK button highlighted, press the SET button and return
to the PRESET STYLE MENU screen.
TITLE PATTERN
BACK
1
Transfer the patterns via a network
ⅥIf BACK is used to exit theTITLE PATTERN screen without the SET button being
pressed for the newly selected pattern, the pattern setting will not be updated.
Create menu patterns on your PC
Ⅵ Main Specifications (Please refer to the above-mentioned home page for the most up-to-date information.)
To change the display pattern for chapter menus, select CHAPTER
PATTERN from the PRESET STYLE MENU screen and then proceed in
the same way as described above.
OS
:
:
Windows XP
Properties set
Thumbnail number, size, and position; background image (per page), and chapter comments.
Thumbnail highlighting format and color; navigation button design and layout.
Readable image files
Layout size
:
:
BMP and JPEG
720 × 480 (NTSC)
Note
The TITLE PATTERN screen and CHAPTER PATTERN screen show the
patterns that are currently stored in your BD-X200.
Display pattern: A combination of thumbnail characteristics (i.e., position,
quantity, and size) and the type of menu background used.
TITLE PATTERN
BACK
4
45
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Title & Chapter Menu Settings
Changing Chapter Menus (THUMBNAIL EDIT screen)
Changing & Naming Thumbnails for Chapter Menus
This DVD recorder can automatically create title and chapter menus as recording operations are started and stopped.
Title and chapter menus are created using the following.
● Title or chapter names : Numbers are applied based on the recording sequence.
The modification of chapter menu thumbnails and the entry of names and comments are carried out as described below using the
THUMBNAIL EDIT screen.
● Chapter thumbnails
● Title thumbnails
: The frames at which chapter marks have been inserted are used as thumbnails.
: The frames at the start of individual recordings are used as thumbnails. As a result, a title’s thumbnail is
the same as that of its first chapter.
: Menus are created using the style set using the PRESET STYLE MENU screen. (Styles determine
factors such as thumbnail positioning and background)
Changing thumbnails
THUMBNAIL EDIT screen
THUMBNAIL EDIT
For example, let’s change the thumbnail for the second chapter.
● Display style
1. Select the second chapter and press the SET button.
TITLE CLOSE
1
-
6
After chapter menus have been created in this way, it will be possible to modify thumbnails and styles, or to insert new names and
comments.
In specific terms, the editing of chapter menus is carried out using the THUMBNAIL EDIT screen that appears when recording of a
title is ended.
● The thumbnail screen for this chapter will be displayed.
AAA
1
BBB
2
CCC
3
1.
2.
2. Select the thumbnail to be used for the second chapter.
Thumbnails can be selected using the † and © buttons found on this screen.
● If you select † and press the SET button, the image* recorded after the
selected thumbnail will be displayed.Each time the SET button is pressed, a
subsequent image will be displayed. (*Image after 15 frames)
● If you select © and press the SET button, the image recorded before the
selected thumbnail will be displayed.Each time the SET button is pressed, a
previous image will be displayed.
DDD
4
EEE
5
Opening the THUMBNAIL EDIT screen
CHAPTER MENU
TEXT LOAD
THUMBNAIL EDIT
BACK
SYSTEM MENU Screen
Ⅵ Set EDIT MENU from the SYSTEM MENU screen to ENABLE.
● The THUMBNAIL EDIT screen will appear automatically whenever moving to
Stop mode from Recording mode or Recording Pause mode.
SYSTEM MENU
MENU
BBB
OFF
OFF
SETUP (U-model only)
TEST SIGNAL
Note
3. Select BACK and press the SET button to change that chapter’s
thumbnail.
2
If EDIT MENU from the SYSTEM MENU screen is set to DISABLE, the
THUMBNAIL EDIT screen will not be displayed.In such a case, title and chapter
menus are created using preset settings.
FACTORY SETTING
KEYBOARD STYLE
EDIT MENU
CANCEL
ENGLISH
ENABLE
PREVIEW
TITLE
● The initial THUMBNAIL EDIT screen is
displayed once again.
THUMBNAIL EDIT
TITLE CLOSE
1
-
6
THUMBNAIL EDIT
BACK
AAA
1
BBBB
2
CCC
3
The thumbnail for the second chapter will have
changed to that just selected.
3.
BBBB
2
DDD
4
EEE
5
FFF
6
Ⅵ THUMBNAIL EDIT screen
When initially displayed, the THUMBNAIL EDIT screen contains thumbnails for up to six recorded chapters in the order that they
were recorded. The seventh and subsequent thumbnails are displayed on the following pages.
● This initial screen can be used to change a chapter’s thumbnail or to input names and comments.
● Operations on this screen can be carried out using the front panel buttons, a keyboard, or a mouse.
Front panel : Select using the t, 8, 6, and 7 buttons, and confirm the selection using the SET button.
Keyboard : Select using the arrow keys and confirm the selection using the Enter key. The input of names and comments is
also carried out using the keyboard.
CHAPTER MENU
TEXT LOAD
PREVIEW
TITLE
* Thumbnail of the title menu will be the top thumbnail of the chapter menu.
Checking thumbnails
Mouse
: Left click the required item.
Use the following procedure to confirm that thumbnails are as desired by displaying
them in full-screen mode.
For example, let’s look at the thumbnail for the second chapter.
THUMBNAIL EDIT
Displays the previous page
Displays the next page
TITLE CLOSE
1
-
6
AAA
1
BBBB
2
CCC
3
This button is used to close a disc’s
titles when editing has been
completed. As such, it should not be
used until all other operations have
been completed.
When title close processing has ended,
the display will return to the E-E screen,
and subsequent editing of chapter
menus will not be possible.
1.
1. Select the second chapter and press the SET button.
THUMBNAIL EDIT
TITLE CLOSE
● The thumbnail screen for this chapter will be displayed.
DDD
4
EEE
5
FFF
6
1 - 6
2. Select PREVIEW and then press the SET button.
CHAPTER MENU
TEXT LOAD
● The thumbnail image for this chapter will be displayed in full-screen mode.
Thumbnail
AAA
1
BBB
2
CCC
3
THUMBNAIL EDIT
BACK
3. Select BACK and press the SET button to return to the THUMBNAIL
EDIT screen.
Chapter number
BBB
DDD
4
EEE
5
FFF
6
2
Highlighted item:
The currently selected item is
displayed in highlighted text.
PREVIEW
TITLE
2.
3.
CHAPTER MENU
TEXT LOAD
BACK
Displays the CHAPTER MENU EDIT screen.
Specifically, this screen is used to check and
change display styles.
Reads title text that has been created using
an external application.
BBBB
47
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Title & Chapter Menu Settings
Changing & Checking Chapter Menu Styles
Although display styles for chapter menus are created using settings from the PRESET STYLE MENU screen as described above,
the following procedure can be used to modify these styles at the end of title recording.In addition, it will also be possible at this time
to confirm that chapter menus are as required.
Entering Names and Comments for Chapter Menus
Use the following procedure to apply names to the thumbnails used in chapter
menus, and also to add comments to be displayed on a chapter menu screen.
ⅥNames and comments are entered using a keyboard.
Set KEYBOARD STYLE from the SYSTEM MENU screen in accordance with
the keyboard’s input language.
ⅥThe following description assumes that all operations are carried out by keyboard.
These actions are carried out by selecting and confirming CHAPTER MENU from the THUMBNAIL EDIT screen.
THUMBNAIL EDIT
TITLE CLOSE
1
-
6
AAA
1
BBB
2
CCC
3
Changing the Display Style
1.
DDD
4
EEE
5
FFF
6
THUMBNAIL EDIT
1. Select CHAPTER MENU from the THUMBNAIL EDIT screen and
TITLE CLOSE
1
-
6
press the SET button.
For example, let’s now apply a name to the first chapter.
CHAPTER MENU
TEXT LOAD
AAA
BBBB
EEE
CCC
FFF
● The CHAPTER MENU EDIT screen will appear.
april
1. Use the arrow keys to select the first chapter from the THUMBNAIL
EDIT screen, and then press the Enter key.
● The thumbnail screen for this chapter will be displayed.
THUMBNAIL EDIT
BACK
2. Select PRESET STYLE from the CHAPTER MENU EDIT screen
and then press the SET button.
DDD
● The PRESET STYLE MENU screen will appear.
The style number set using the PRESET STYLE parameter will be displayed
in this screen.
AAA
CHAPTER MENU
TEXT LOAD
1.
2.
2. Select TITLE using the arrow keys and then press the Enter key.
● A box for inputting text will appear.
CHAPTER MENU
2.
3.
BACK
3. To change the display PATTERN;
3. Enter a name or comment into the text box.
PREVIEW
TEXT INPUT
PRESET STYLE
Select PATTERN and then press the SET button.
Turn to page 44 for details regarding the editing procedure.
CHAPTER MENU PREVIEW
THUMBNAIL EDIT
BACK
Enter a comment to be displayed on
the chapter menu screen.
*
TITLE PATTERN and CHAPTER PATTERN changed here are also reflected in
PRESET STYLE of the SETUP MENU.
AAA
*******************************
Enter a name for the chapter
TITLE INPUT
menu thumbnail. (Names can be
up to 20 characters in length.)
*******************************
april
PRESET STYLE MENU screen
TITLE INPUT
1april
CANCEL
PRESET STYLE
CANCEL
BACK
TYPE
1
Select CANCEL and press the Enter key to
close the text box without applying the name
or comment that has been entered.
TITLE PATTERN
1
1
THUMBNAIL EDIT
BACK
3.
CHAPTER PATTERN
AAA
april
Notes
● The ¥ mark will become a backslash.
● If text cannot be entered, press the CTRL key (right side) on the keyboard.
PREVIEW
TEXT INPUT
4. After the required text has been entered, press the Enter key.
● The text box will close.
THUMBNAIL EDIT
TITLE CLOSE
1
-
6
The field previously showing the chapter number will now be highlighted
showing the text that was input.
The text that has been input will be displayed on the chapter menu screen.
AAA
april
BBBB
EEE
CCC
FFF
*
DDD
5. Select BACK and then press the Enter key.
● The initial THUMBNAIL EDIT screen will again be displayed, and the name
or comment will be shown for the first chapter.
CHAPTER MENU
TEXT LOAD
Display Characters
The characters displayed in title and
chapter menus depend on the title
or chapter pattern that has been
selected. A preview allows actual
display characters to be confirmed.
Note that at the time of purchase,
display characters will be as follows.
Note
If you select TEXT LOAD from the THUMBNAIL
EDIT screen and then press the SET button, title
text created using an external application will be
read into the DVD recorder for use as a thumbnail
name.
THUMBNAIL EDIT
TITLE CLOSE
1
-
6
AAA
1
BBB
2
CCC
3
DDD
4
EEE
5
FFF
6
PATTERN No.
Display characters
CHAPTER MENU
TEXT LOAD
TEXT LOAD
1
2
3
4
5
6
16
19
17
20 (15 + line return + 5)
16
—
49
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Title & Chapter Menu Settings
Ending the Editing of Chapter Menus
Once all of the necessary changes and checks have been made using the THUMBNAIL EDIT screen, title closing must be carried
out.
Checking the Chapter Menu Screen
Please ensure that title closing is performed as the last stage of chapter menu editing.
Even if the chapter menu is to be left unchanged, title closing must be carried out to leave the THUMBNAIL EDIT screen. Note that
when title closing has been completed, chapter menu details will be permanently set.
Use the following procedure to see how the chapter menu looks when the selected display style is used.
THUMBNAIL EDIT START screen
1. Select CHAPTER MENU from theTHUMBNAIL EDIT START screen
THUMBNAIL EDIT
and press the SET button.
TITLE CLOSE
1
-
6
THUMBNAIL EDIT
1. Select TITLE CLOSE from the THUMBNAIL EDIT screen and press
● The CHAPTER MENU EDIT screen will appear.
TITLE CLOSE
1.
AAA
april
BBBB
EEE
CCC
FFF
the SET button.
AAA
april
BBBB
EEE
CCC
FFF
● A confirmation window will appear.
2. Select CHAPTER MENU PREVIEW from the CHAPTER MENU EDIT
screen and press the SET button.
DDD
DDD
2. If you wish to proceed with title closing, selectYES and then press
● The CHAPTER MENU PREVIEW screen will appear.Here, it will be possible
to preview the first page of the chapter menu.
the SET button.
CHAPTER MENU
TEXT LOAD
1.
2.
● Title closing will begin.The state of progress during title closing is displayed
CHAPTER MENU
TEXT LOAD
using a progress bar.
3. Confirm that the other pages are as required.
Select † from the CHAPTER MENU PREVIEW screen and press the SET
button to move to the next page.
Select © and press the SET button to move to the previous page.
††and ©©can be used in combination with the SET button to skip forward
or back in units of ten pages.
CHAPTER MENU EDIT screen
THUMBNAIL EDIT
TITLE CLOSE
CHAPTER MENU
BACK
AAA
april
BBBB
CCC
PRESET STYLE
CHAPTER MENU PREVIEW
RGRJCꢀAJMQC
TITLE CLOSE
WCQ
LM
2.
4. Complete the preview process.
CHAPTER MENU
TEXT LOAD
To do this, select BACK from the CHAPTER MENU PREVIEW screen and
press the SET button.
● The CHAPTER MENU EDIT screen will reappear.
Select NO and then press
the SET button to close the
confirmation window.
The title will not be closed
in this case.
CHAPTER MENU PREVIEW screen
5. Select BACK from the CHAPTER MENU EDIT screen and press
the SET button to return to the THUMBNAIL EDIT screen.
Ⅵ When title closing has been completed, the progress bar will disappear.
BACK
1
4.
01
02
03
Notes
Notes
● Up to 20 seconds per page will be required to create preview displays.
More time may be required depending on the number of thumbnails per
page.
● A maximum of 10 minutes will be required to complete title closing.
● If EDIT MENU from the SYSTEM MENU screen is set to DISABLE, title
closing will be carried out automatically whenever recording is ended by, for
example, pressing the STOP button.In such a case, title and chapter menus
are created using preset settings.
● During creation of preview displays, jump by selecting the †† button can
only be made to the page being created.
51
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Title & Chapter Menu Settings
Changing & Checking Title Menu Styles & Names
Changing & Checking Title Menu Styles & Names (continued)
If EDIT MENU from the SYSTEM MENU screen is set to ENABLE, the TITLE MENU EDIT screen will be displayed upon disc
finalizing. Using this screen, it will be possible to change the title menu’s display style, to enter title names, and to confirm that the
title and chapter menus are as required.
Checking the Title Menu Screen
● Thumbnail of the title menu will be the top thumbnail of the chapter menu.
TITLE MENU EDIT screen
1. Select TITLE MENU PREVIEW from the TITLE MENU EDIT screen
and press the SET button.
TITLE MENU
FINALIZE
● The TITLE MENU EDIT screen will appear.
Opening the TITLE MENU EDIT screen
PRESET STYLE
TITLE TEXT INPUT
2. Confirm that the other pages are as required.
● Select †from theTITLE MENU PREVIEW screen and press the SET button
to move to the next page. Starting with the first page of the title menu, the
display will move forward through the pages each time ¥ is selected and
the SET button is pressed.
TITLE MENU PREVIEW
EXIT
TITLE MENU EDIT screen
1.
3.
Settings
TITLE MENU
Set EDIT MENU from the SYSTEM MENU screen to ENABLE.
FINALIZE
PRESET STYLE
TITLE TEXT INPUT
● Select © and press the SET button to move to the previous page.
● †† and ©© can be used in combination with the SET button to skip
forward or back in units of ten pages.
Procedure
TITLE MENU PREVIEW
TITLE MENU PREVIEW screen
EXIT
The TITLE MENU EDIT screen will be displayed when finalizing of the disc is
started.
BACK
1
Displays the previous page
Displays the next page
01
02
03
BACK
1
Displays the page
number
01
02
03
Changing the Display Style
Thumbnail
Background
TITLE MENU EDIT screen
1. Select PRESET STYLE from the TITLE MENU EDIT screen and
TITLE MENU EDIT screen
press the SET button.
TITLE MENU
TITLE MENU
FINALIZE
● The PRESET STYLE screen will appear.
FINALIZE
4.
PRESET STYLE
1.
PRESET STYLE
TITLE TEXT INPUT
TITLE MENU PREVIEW
EXIT
2. To change the display PATTERN;
TITLE TEXT INPUT
3. Complete the preview process.
TITLE MENU PREVIEW
Select TITLE PATTERN and then press the SET button.
EXIT
To do this, select BACK from the TITLE MENU PREVIEW screen and press
the SET button.
For more details regarding the editing procedure, refer to page 45.
● The TITLE MENU EDIT screen will reappear.
*
The TITLE PATTERN changed here is also reflected in PRESET STYLE of the
SETUP MENU.
4. If you wish to finalize the disc, select FINALIZE from the TITLE
MENU EDIT screen and then press the SET button.
(☞ page 56)
PRESET STYLE screen
PRESET STYLE
BACK
TYPE
1
1
Notes
TITLE PATTERN
2.
● Up to 20 seconds may be required per page to display the PREVIEW screen.
More time may be required depending on the number of thumbnails per
page.
● During creation of preview displays, jump by selecting the †† button can
only be made to the page being created.
53
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Title & Chapter Menu Settings
Changing & Checking Title Menu Styles & Names (continued)
Entering Names for the Title Menu
Finalizing Discs
Use the following procedure to enter names for titles in the title menu.
TITLE MENU EDIT screen
1. Select FINALIZE from the TITLE MENU EDIT screen and press the
TITLE MENU EDIT screen
Ⅵ Names and comments are entered using a keyboard.
Set KEYBOARD STYLE from the SYSTEM MENU screen in accordance with
the keyboard’s input language.
SET button.
TITLE MENU
TITLE MENU
FINALIZE
● A confirmation window will appear.
1.
FINALIZE
PRESET STYLE
ⅥThe following description assumes that all operations are carried out by keyboard.
TITLE TEXT INPUT
PRESET STYLE
TITLE TEXT INPUT
TITLE MENU PREVIEW
EXIT
2. Select YES and then press the SET button.
● The disc finalizing process will begin.
TITLE MENU PREVIEW
EXIT
1.
2.
4.
1. Select TITLE TEXT INPUT from the TITLE MENU EDIT screen and
press the Enter key.
● The TITLE TEXT INPUT screen is displayed.
The state of progress during finalizing is displayed using a progress bar.
ⅥWhen the disc has been finalized, the progress bar will disappear and the E-E
screen will return.
2. Use the arrow keys to select the title for which text is to be input.
Confirmation screen
● The currently selected title is highlighted.
Notes
TITLE TEXT INPUT screen
TITLE TEXT INPUT
● A maximum of 20 minutes will be required to complete finalizing.
● When finalizing is carried out, all of the disc’s recorded video and audio are
stored in accordance with the DVDVideo Standard;accordingly, this content
can then also be replayed as DVD video.
● Although a disc finalized using this DVD recorder may in principle be played
on other DVD players, there is no guarantee that all of its content will be
playable.
● The action to be taken by this DVD recorder when a finalized disc is inserted
or when playback of a title has ended is specified by DISC IN ACTION and
TITLE END respectively from the RECORDER MENU (2/2) screen.
● Select EXIT from the TITLE MENU EDIT screen and then press the SET
button to return to the E-E screen without finalizing the disc.
3. Press the Enter key.
BACK
1
1
1
-
-
-
6
6
6
● A box for inputting text will appear.
AAA
DDD
BBB
CCC
CCC
CCC
FINALIZE
4. Enter a name or comment into the text box.
YES
NO
2.
TITLE INPUT
august
Enter a name for the title.
(Names can be up to 20
characters in length.)
TEXT LOAD
Progress screen
CANCEL
TITLE TEXT INPUT
BACK
Select CANCEL and press the Enter key to
close the text box without applying the
name or comment that has been entered.
AAA
BBB
TITLE INPUT
august
FINALIZE
CANCEL
Notes
TEXT LOAD
● The ¥ mark will become a backslash.
● If text cannot be entered, press the CTRL key (right side) on the keyboard.
TITLE TEXT INPUT
BACK
6.
5.
5. After the required text has been entered, press the Enter key.
● The text box will close.
AAA
BBB
august
The name just entered will be applied to the selected title.
DDD
6. Select BACK and then press the Enter key.
TEXT LOAD
● The TITLE MENU EDIT screen will reappear.
Display Characters
The characters displayed in title and
chapter menus depend on the title
or chapter pattern that has been
selected. A preview allows actual
display characters to be confirmed.
Note that at the time of purchase,
display characters will be as follows.
Note
If you select TEXT LOAD from the TITLE
TITLE TEXT INPUT
BACK
1
-
6
MENU screen and then press the SET button,
title text created using an external application
will be read into the DVD recorder for use as
a title name.
AAA
DDD
BBB
CCC
PATTERN No.
Display characters
TEXT LOAD
TEXT LOAD
1
2
3
4
5
6
16
19
17
20 (15 + line return + 5)
16
—
55
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Playback
Playing Discs
Fast & Slow Playback
This DVD recorder can also be used to playback discs that it has recorded and finalized.
When a disc is finalized, its title menu will be used to create the top menu.
The action taken by your BD-X200 when a disc it has finalized is inserted or when playback of a title has ended will depend on the
settings of DISC IN ACTION and TITLE END as set on the RECORDER MENU (2/2) screen during recording.
BUSY
OPERATE
OPEN/CLOSE
*
Playback may not proceed smoothly with discs recorded using different devices, regardless of whether or not they have been
finalized.
OPTION DV Y/C LINE
SET UP
DVD RECORDER BD-X200
TITLE
AUDIO
CH1
CHAPTER
DOLBY DIGITAL
LPCMMPEG
CH2
BUSY
SET
TOP
PHONES
REV
STOP
PLAY
FWD
PAUSE
REC
MENU
MENU
OPERATE
OPEN/CLOSE
OPTION DV Y/C LINE
SET UP
DVD RECORDER BD-X200
TITLE
AUDIO
CHAPTER
CH1
CH2
REV button
FWD button
DOLBY DIGITAL
LPCMMPEG
SET
TOP
Cursor buttons
PHONES
REV
STOP
PLAY
FWD
PAUSE
REC
MENU
MENU
(t, 8, 7, and 6)
Fast-Forward & Fast-Reverse Play
Ⅵ Fast-forwarding
Slow-Forward & Slow-Reverse Play
Ⅵ Slow-forwarding
SET button
● Press the FWD button during playback or fast-reverse play
to start fast-forward play.
If pressed again during fast-forward play, this button toggles
the speed of fast-forward play between ×3 and ×15.
● Press the FWD button in Still mode or during slow-reverse
play to start slow-forward play.
If pressed again during slow-forward play, this button toggles
the speed of slow-forward play between ×0.5 and ×0.06.
PAUSE button
STOP button
PLAY button
1. Insert a disc.
Ⅵ Fast-reversing
● Press the REV button during playback or fast-forward play
to start fast-reverse play.
Ⅵ Slow-reversing
● Press the REV button in Still mode or during slow-forward
play to start slow-reverse play.
The action of the DVD recorder depends on the setting of DISC IN ACTION from the RECORDER MENU (2/2) screen. The
following table describes the operations to be performed in either case.
If pressed again during fast-reverse play, this button toggles
the speed of fast-reverse play between ×3 and ×15.
If pressed again during slow-reverse play, this button toggles
the speed of slow-reverse play between ×0.5 and ×0.06.
DISC IN ACTION setting made during recording
MENU
TITLE
Notes
The title menu will appear
Playback starts automatically from the first title.
● The DVD recorder can be returned to Playback mode during fast-forward, fast-reverse, slow-forward, or slow-reverse play by
pressing the PLAY button. Still mode can be activated by pressing the PAUSE button. Stop mode is activated by pressing the
STOP button.
2. Select the number of the title to be played.
Use the t, 8, 7, and 6buttons to select the title number
for playback.
● The displayed playback speed is not an exact value.
3. Press the SET button to begin playback.
4. Set to Still mode.
Playing the Previous or Next Chapter
This is done by pressing the PAUSE button.
● The DVD recorder enters Still mode.
Ⅵ Press the t button while the DVD recorder is playing to move playback to the
start of the next chapter.
● If the PAUSE button is then pressed again in Still mode, the DVD recorder will advance playback by a single frame.
Ⅵ Press the 8 button while the DVD recorder is playing to move playback to the
start of the current chapter.
If the 8 button is pressed while the DVD recorder is playing the first chapter,
5. Restart playback.
OPTION DV Y/C LINE
SET UP
Press the PLAY button.
playback will return to the beginning of that chapter.
* The t button is deactivated during playback of the final chapter.
Ⅵ
The DVD recorder will behave as follows when title playback has ended.
These actions will depend on the setting made for TITLE END from the RECORDER MENU (2/2) screen during recording.
SET
TOP
MENU
MENU
TITLE END SETTING made during recording
MENU
REPEAT
t button
8 button
The DVD recorder enters Stop mode and displays the title
menu.
Repeat playback is carried out within the title.
6. Stop playback.
This is done by pressing the STOP button.
● The DVD recorder enters Stop mode.
57
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Synchronous Recording
Synchronous Recording
Recording Playback Signals From a VCR with RS-422A
Recording Playback Signals From a VCR with RS-422A (continued)
Editing Via the REMOTE CONTROL (9PIN MASTER/DV MASTER) Screen
RS-422A control can be used to record playback signals from aVCR with an RS-422A terminal to a disc in your BD-X200.It will also
be possible to control that VCR using this DVD recorder’s REMOTE CONTROL screen.
Signal Connections
A keyboard and mouse can be used as an alternative to the DVD recorder’s buttons when using the REMOTE CONTROL (9PIN
MASTER/DV MASTER) screen.
Front panel
Keyboard
Mouse
:
:
:
Select using the cursor buttons (t, 8, 7, and 6), and confirm the selection using the SET button.
Select using the arrow keys (†, ©, √, and ∞), and confirm the selection using the Enter key.
Left click the required button.
VIDEO OUT
VIDEO IN
AUDIO IN
AUDIO OUT
VIDEO OUT
* When the REMOTE CONTROL screen is being displayed, the DVD recorder’s, FWD, REV, PLAY, REC, PAUSE, MENU, and TOP
MENU buttons will be disabled.
VIDEO
LINE
AUDIO
IN
IN
OUT
INPUT
LEVEL
CH1
OUT
VIDEO CASSETTE RECORDER
AUDIO
INPUT
VIDEO
INPUT
AUDIO INPUT
/
AUDIO MONITOR SELECT
POWER
4dB
8dB
SDI
CH1
CH1
CH1
CH2
CH2
CH2
CH3
CH3
CH3
CH4
CH4
CH4
SIF
ON
I
AUDIO
MONITOR
A
E
S
/
E
B
U
LINE
CPN
L
A
N
A
L
O
G
R
Y/C
OFF
O
IN
AUDIO OUT
Variable Motion
CH1
CH2
CH3
CH4/TRACKING
S
E
A
R
C
H
V
A
R
PLAYER RECORDER
CH2
R
P
R
P
R
P
R
P
C
O
U
N
T
E
R
R
E
S
E
T
VCON
REMOTE
C
T
L
T
C
U
B
D
F
S
E
R
V
O
C
F
G
E
N
1
R
6
E
:
M
9
A
OT
P
E
5
62
2
5
5
CONDITION
dB OVER dB
dB OVER dB
dB OVER dB
dB OVER dB
0
0
0
0
A
U
T
O
O
F
F
P
.
R
E
A
D
V
.
V
A
R
P
B
/
E
E
UB
+4
+4
+4
+4
REMOTE
–10
–10
–10
–10
PB
+2
0
+2
0
+2
0
+2
0
P.PLAY
In Point (start point for editing):
Out Point (end point for editing):
MENU
REC
SET
HOLD
PB/EE
DV IN/OUT
–20
–20
–20
–20
STILL
–2
–2
–2
–2
–30
–40
–30
–40
–30
–40
–30
–40
H
M
S
F
–4
–4
–4
–4
–60
–60
–60
–60
A
S
S
E
M
V
I
D
E
O
DA1
DA2
DA3
DA4
EJECT
PLAY
P
A
U
S
E/S
T
I
L
L
X-1
X1
USB
LAN
Set the time code (hours : minutes : seconds : frames) of
the position on the playback tape where recording is to
be started.
Set the time code (hours : minutes : seconds : frames) of
the position on the playback tape where recording is to
be stopped.
CH1
CH2
CH3
CH4
SIGNAL
PHONES
REC
TRACKING
DC 19V
REMOTE
INSERT
GND
IN
ENTRY
OUT
TC
TOP
VIDEO
STOP
AUDIO
FF
PULL FOR VARIABLE
METER MODE
FINE TRACKING
STAND BY
REW
CANCEL PREVIEW
REVIEW
AUTO EDIT
PREROLL
PULL
RELEASE
PULL
RELEASE
PLAY
SHIFT
USER
SERVO/SYS
TIME CODE
ON SCREEN
OTHERS
FWD
REV
USB terminal
VCR with an RS-422A terminal
Chapter list:
TC INPUT:
This displays the time
codes of chapter
marks.
● The In Point’s time
code is registered as
the first chapter
mark.
MONITOR OUT
This field is used to input
REMOTE CONTROL SCREEN ( 9PIN MASTER )
00:00:00:00
OUT POINT
00:10:00:00
time codes for the In
Point, Out Point, and
chapter marks from the
keyboard.
EXIT
h
1
4
7
IN POINT
Keyboard
Print
Pause
Break
Scroll
Lock
Esc
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
Screen
Sysrq
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
あ
う
え
お
や
ゆ
よ
～
0
！
1
#
3
$
4
%
5
&
6
(
8
)
9
=
-
”
2
'
7
Back
Page
Up
Num
Insert
Home
End
/
Space
Lock
-
^
￥
」
*
9
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
Q
W
E
R
T
Y
U
I
O
P
｀
「
]
7
8
Page
Tab
Enter
Delete
Down
[
@
+
Caps Lock
＋
＊
A
S
D
F
G
H
J
K
L
4
1
0
5
2
6
;
:
つ
<
,
、
>
.
。
Z
X
C
V
B
N
M
?
/
・
＿
/
Shift
Shift
Mouse
Enter
.
Ctrl
Alt
Alt
Ctrl
DISC REMAIN:
● A total of 98 chapters
can be setup.
Monitor
Monitor
:
:
:
CHAPTER
MANUAL
TC INPUT
This field shows an
estimate of the remaining
space for recording on the
disc.
000 min
FINALIZE
8.0 Mbps DISC REMAIN
BITRATE
TC SET
TC CANCEL
ADJ
● When CHAPTER
CREATION from the
RECORDER MENU
(2/2) screen is set to
MANUAL, it will be
possible to setup
chapter marks at any
position on the
playback tape.
● Connect the RS-422A REMOTE terminal on the rear of the DVD recorder to the remote RS-422A terminal on the VCR using an
RS-422A cable.
● Connect the DVD recorder’s VIDEO LINE IN and AUDIO IN terminals to the VCR’s video out and audio out terminals.
● Connect the DVD recorder’s VIDEO LINE OUT and AUDIO OUT terminals to the monitor’s video in and audio in terminals.
● A keyboard and mouse can be used as an alternative to the DVD recorder’s buttons when using the REMOTE CONTROL screen.
If used, these are to be connected to each of the USB terminals on the rear panel.
EDL LOAD
EDIT/END
FINALIZE:
This button is used to
finalize the disc.
Setup Procedures
● Insert the tape for playback into the VCR. Ensure that this tape contains an SMPTE time code.
● Insert a recordable disc into your BD-X200.
ADJUST:
TC SET
:
This button is used to set input time codes for
the In Point, Out Point, and chapter marks.
This button can be
pressed to determine
the remaining disc time
based on the editing
time and to also set a
suitable bit rate. This
TC CANCEL : This button is used to remove setting values
for the In Point, Out Point, and chapter marks.
Settings
CHAPTER:
EDL LOAD
:
This button is used to load the most-recent
edit list. It can be used whenever CREATION
CHAPTER has been set to MANUAL.
The right-hand field indicates
the current setting for
CHAPTER CREATION from
the RECORDER MENU (2/2)
screen.
● When set to MANUAL,
chapter marks can be
registered in this screen’s
chapter list.
VCR
:
:
Enable control via RS-422A.
Set REMOTE SELECT from the REMOTE MENU screen to 9PIN (MASTER).
BD-X200
setting
displayed in the BIT
RATE field.
is
then
EDIT/END
:
This button is used to start editing
automatically.When recording has ended, the
DVD recorder automatically adopts Recording
STOP mode. If selected while editing, this
button will end that process.
● When REMOTE SELECT is set to 9PIN (MASTER), the REMOTE CONTROL
(9PIN MASTER) screen will appear. This screen is used to perform editing
operations, and the corresponding operations are described on the following
pages.
REMOTE MENU screen
REMOTE MENU
MENU
9PIN(MASTER)
OFF
REMOTE SELECT
REC CONTROL
REMOTE CONTROL (9PIN MASTER) screen
FF/REW
REM FF/REW MODE
● When set to AUTO, the
DVD recorder’s chapter
auto-create function will set
chapters. In such a case, it
will not be possible to
register chapters using this
screen’s chapter list.
● Chapter marks are
inserted at GOP intervals
(i.e., 15 frames). It will not
be possible to insert
chapter marks that are
closer together than this
interval.
REMOTE CONTROL SCREEN ( 9PIN MASTER )
VCR Control Panel
EXIT
h
1
4
7
IN POINT
00:00:00:00
OUT POINT
00:10:00:00
The buttons provided in this panel are used to control VCR operations. When a
button is selected and confirmed, theVCR will carry out the corresponding operation.
It is important to remember that these buttons do not control operation of this DVD
recorder.
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
e
: Eject
w
: Pause
: Play
: Frame-advance play
:
:
CHAPTER
MANUAL
TC INPUT
u : Fast reverse or fast-reverse play
t
Note
000 min
8.0 Mbps DISC REMAIN
BITRATE
TC SET
TC CANCEL
ADJ
: Frame-Reverse play
When pressing and holding the REC
button more than 2 seconds while the DVD
recorder is stopped, encoded output
images can be checked while the button
is being held.
FINALIZE
EDL LOAD
EDIT/END
q
: Stop
y : Fast forward or fast-forward play
*
The action to be taken by the DVD recorder in response to pressing of the y or
u button (i.e., FF/REW or SEARCH) is selected using REM FF/REW MODE
from the REMOTE MENU screen.
59
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Synchronous Recording
Recording Playback Signals From a VCR with RS-422A (continued)
2. Deleting the In Point, Out Point, and Chapter Marks
1. Registering the In Point, Out Point, and Chapter Marks
q Use the cursor buttons (t, 8, 7, and 6) to select the point to
be deleted (i.e., In Point, Out Point, or a chapter mark from the
chapter list), and then press the SET button.
w Use the cursor buttons (t, 8, 7, and 6) to select TC CANCEL
and press the SET button.
● The selected point (i.e., the In Point, Out Point, or a chapter
mark from the chapter list) will be deleted.
● Whenever a chapter mark is deleted, the chapter list will be
resorted.
The following two methods can be used to register the In Point, Out Point, and chapter marks.
● Recording of time codes corresponding to tape positions.
● Direct entry using a keyboard.
Registering chapter marks : In order to register chapter marks using the REMOTE CONTROL screen, it will first of all be necessary
to set CHAPTER CREATION from the RECORDER MENU (2/2) screen to MANUAL.If this parameter
is set to AUTO, chapter marks will be automatically setup at specific intervals.The current setting for
CHAPTER CREATION is indicated in this screen’s CHAPTER field.
q
REMOTE CONTROL SCREEN ( 9PIN MASTER )
EXIT
h
1
4
7
IN POINT
00:00:00:00
OUT POINT
00:10:00:00
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
:
:
:
CHAPTER
MANUAL
TC INPUT
8.0 Mbps DISC REMAIN
000 min
FINALIZE
BITRATE
TC SET
TC CANCEL
ADJ
Recording from tape positions
Direct keyboard entry
q
EDL LOAD
EDIT/END
w
w
REMOTE CONTROL SCREEN ( 9PIN MASTER )
REMOTE CONTROL SCREEN ( 9PIN MASTER )
IN POINT
00:00:00:00
EXIT
h
1
4
7
OUT POINT
00:10:00:00
IN POINT
00:00:00:00
EXIT
h
1
4
7
OUT POINT
00:10:00:00
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
3. Starting the Record Process
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
q Select EDIT/END from the REMOTE CONTROL screen and
press the SET button.
● VCR will begin playback by returning to the position 5 seconds
before the IN POINT.
● The unit will start record when the VCR reaches the IN POINT.
Recording of video and audio from the VCR to the DVD will be
carried out from the In Point to the Out Point with chapters
being created as specified.
w When playback reaches the Out Point, title recording will end
automatically.
:
:
:
CHAPTER
MANUAL
REMOTE CONTROL SCREEN ( 9PIN MASTER )
TC INPUT
:
:
:
CHAPTER
MANUAL
TC INPUT
w
EXIT
h
1
4
7
IN POINT
00:00:00:00
OUT POINT
00:10:00:00
000 min
FINALIZE
8.0 Mbps DISC REMAIN
BITRATE
TC SET
TC CANCEL
ADJ
000 min
FINALIZE
8.0 Mbps DISC REMAIN
BITRATE
TC SET
TC CANCEL
ADJ
EDL LOAD
EDIT/END
e
q
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
EDL LOAD
EDIT/END
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
:
:
:
CHAPTER
MANUAL
TC INPUT
000 min
FINALIZE
8.0 Mbps DISC REMAIN
BITRATE
TC SET
TC CANCEL
ADJ
EDL LOAD
EDIT/END
w
● The VCR will automatically adopt STOP mode at this time.
● The DVD recorder will return to Stop mode and will end title
recording.
Ⅵ If another title is to be recorded, repeat operations from the
registration of the In Point and Out Point.
q Use the VCR Control Panel to start playback on the VCR.
Press the STILL (w) button and pause VCR playback at the
position to be registered. If necessary, use frame advance,
and the like to set the exact position.
q Use the arrow keys (†, ©, ∞, and √) to select the point to
be registered (i.e., the In Point or Out Point), and then press
the Enter key.
EDIT/END
w Select the TC INPUT button using the cursor keys and input
a time code (hours: minutes: seconds: frames) into the TC
input field using the keyboard.
w Use the cursor buttons (t, 8, 7, and 6) to select the point
to be registered (i.e., the In Point or Out Point), and then
press the SET button.
Notes
● Editing accuracy is 5 frames.
e Press the Enter key.
● If no In Point has been registered, recording will begin at the current tape position. However, the tape must be positioned
before the Out Point and all chapter marks for this to be possible.
● If no Out Point has been registered, a manual stop must be carried out to end recording. Select EDIT/END to end the editing
process.
*
The selected point will be highlighted.
● The time code will be registered for the selected point.
● If both IN point and OUT point are not selected, the time
code will be registered as a chapter point
e Use the cursor buttons (t, 8, 7, and 6) to select TC SET
and press the SET button.
● The time code will be registered for the selected point.
● If both IN point and OUT point are not selected, the time
code will be registered as a chapter point.
● When a time code is registered for a chapter mark, the
chapter list will be sorted from the smallest time-code
values, and the newly registered point will be highlighted.
● When the chapter auto-create function is used, chapters will be created at specific intervals.
● When a time code is registered for a chapter mark, the
chapter list will be sorted from the smallest time-code
values, and the newly registered point will be highlighted.
Setting the Optimum Bit Rate
Note
The framing mode will be matched to that used for time
codes on the connected device. When in the drop frame
mode, a value corrected automatically will be registered
when inputting the frame to drop. (U-model only)
ADJUST can be used to set the optimum bit rate (i.e., the amount of data per
second) for the remaining space on a disc based on the recording time (or duration)
between the In Point and the Out Point.
● DISC REMAIN displays an estimate of the available space for recording on the
current disc.
● BIT RATE displays the current bit-rate setting.
To set the bit rate that best suits the remaining disc capacity, select ADJUST and
then press the SET button.
REMOTE CONTROL SCREEN
(
9PIN MASTER
)
*
Editing can only be performed when there is continuous
time code up to 5 seconds from IN POINT.
EXIT
h
1
4
7
IN POINT 00:00:00:00
OUT POINT 00:10:00:00
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
:
:
:
CHAPTER
MANUAL
TC INPUT
8.0 Mbps DISC REMAIN
000 min
FINALIZE
ADJ BITRATE
TC SET
EDL LOAD
EDIT/END
TC CANCEL
Saving & Loading Time-Code Settings
Once settings have been made, they can be saved in your BD-X200’s internal memory. Even if
a different screen is opened or the power is turned off, stored data can then be loaded by
selecting EDL LOAD from the REMOTE CONTROL screen and pressing the Set button.
● If CHAPTER CREATION from the RECORDER MENU (2/2) screen is set to AUTO, it will not
be possible to select EDL LOAD on the REMOTE CONTROL screen.
● Whenever an external edit list (EDL) is read or time-code registration is started without
performing EDL LOAD, the settings will be updated accordingly. As a result, even if EDL
LOAD is selected in such a case, the previous data will not be reloaded.
ADJUST
REMOTE CONTROL SCREEN
(
9PIN MASTER
)
EXIT
h
1
4
7
IN POINT 00:00:00:00
OUT POINT 00:10:00:00
FINALIZE
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
4. Ending the Record Process
:
:
:
CHAPTER
MANUAL
TC INPUT
8.0 Mbps DISC REMAIN
000 min
FINALIZE
ADJ BITRATE
TC SET
EDL LOAD
EDIT/END
TC CANCEL
Ⅵ If you intend to play the recorded disc on this DVD recorder or on another player, select FINALIZE and press the SET button.
Once finalizing has been carried out, no addition recordings can be made on the disc.
Ⅵ To remove the recorded disc from your BD-X200, press the OPEN/CLOSE button on the front panel.
Refer to page 68 for more details regarding the loading of external EDL.
EDL LOAD
61
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Synchronous Recording
Recording Playback Signals From a DV Camera or VCR
Recording Video & Audio From a Non-Linear Editor
DV (IEEE1394) control can be used to record playback signals from a camera or VCR with a DV terminal to a disc in your BD-X200.
It will then be possible to control that VCR using this DVD recorder’s REMOTE CONTROL screen.
By connecting a non-linear editor featuring a DV terminal to this DVD recorder, audio and video processed using the editor can be
easily recorded to a disc.In this case, the BD-X200 will be controlled by commands from the non-linear editor, and these commands
will be communicated via the DV terminal.
Signal Connections
Monitor
Signal Connections
Monitor
AUDIO OUT
Rear panel
DV camera or VCR
VIDEO OUT
VIDEO
LINE
AUDIO
IN
IN
OUT
INPUT
LEVEL
CH1
OUT
MIC
1
IN
4dB
8dB
Y/C
IN
AUDIO OUT
MIC
2
IN
CH2
Rear panel
REMOTE
VIDEO OUT
DV IN/OUT
DV IN/OUT terminal
DV terminal
USB
LAN
VIDEO
LINE
AUDIO
IN
SIGNAL
GND
DC 19V
IN
OUT
INPUT
LEVEL
CH1
(video, audio, and control signals)
OUT
4dB
8dB
VIDEO OUT
Y/C
IN
DV cables:
USB terminal
CH2
VC-VDV204 (2 m, 4P-4P) from JVC
REMOTE
DV IN/OUT
VC-VDV206 (2 m, 4P-6P) from JVC
USB
LAN
SIGNAL
GND
DC 19V
Keyboard
DV IN/OUT terminal
(video, audio, and control signals)
Print
Pause
Scroll
Lock
Esc
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
Screen
Sysrq
Break
DV terminal
あ
う
え
お
や
ゆ
よ
～
0
！
1
#
3
$
4
%
5
&
6
(
8
)
9
=
-
”
'
7
Back
Page
Up
Num
DV cables:
VC-VDV204 (2 m, 4P-4P) from JVC
VC-VDV206 (2 m, 4P-6P) from JVC
Insert
Home
End
/
Space
Lock
-
2
^
￥
」
*
9
Q
W
E
R
T
Y
U
I
O
P
｀
「
]
7
8
Non-linear editor
Page
T
ab
Enter
Delete
Down
[
@
Monitor
+
Caps Lock
＋
＊
A
S
D
F
G
H
J
K
L
4
1
0
5
2
6
;
:
つ
<
,
、
>
。
Z
X
C
V
B
N
M
?
/
・
＿
Shift
Shift
.
/
Mouse
Enter
.
Ctrl
Alt
Alt
Ctrl
● Connect the DV IN/OUT terminal on the rear of your BD-X200 to the DV terminal on the non-linear editor using a DV (IEEE1394)
cable. One of the commercially-available cables indicated above should be used for this purpose.
● Connect the DVD recorder’s VIDEO LINE OUT and AUDIO OUT terminals to the monitor’s video in and audio in terminals.
● Connect the DV IN/OUT terminal on the rear of your BD-X200 to the DV terminal on the DV camera orVCR using a DV (IEEE1394)
cable. One of the commercially-available cables indicated above should be used for this purpose.
● Connect the DVD recorder’s VIDEO LINE OUT and AUDIO OUT terminals to the monitor’s video in and audio in terminals.
● A keyboard and mouse can be used as an alternative to the DVD recorder’s buttons when using the REMOTE CONTROL screen.
If used, these are to be connected to each of the USB terminals on the rear panel.
Setup Procedures
● Insert a recordable disc into your BD-X200.
Setup Procedures
Settings
● Insert the tape for playback into the camera or VCR. Ensure that this tape contains an SMPTE time code.
● Insert a recordable disc into your BD-X200.
BD-X200
:
Set REMOTE SELECT from the REMOTE MENU screen to DV (SLAVE).
● When REMOTE SELECT is set to DV (SLAVE), the REMOTE CONTROL (DV
SLAVE) screen will appear. This screen can be used to set editing points and
chapter marks. Refer to page 65 for details regarding usage of the REMOTE
CONTROL (DV SLAVE) screen.
REMOTE MENU screen
Settings
REMOTE MENU
DV camera or VCR
BD-X200
:
:
Enable control via DV.
Set REMOTE SELECT from the REMOTE MENU screen to DV (MASTER).
MENU
DV(SLAVE)
OFF
REMOTE SELECT
REC CONTROL
● When REMOTE SELECT is set to DV (MASTER), the REMOTE CONTROL (DV
MASTER) screen will appear.This screen is used to perform editing operations,
and the corresponding operations are described on pages 60 through 62.
REMOTE MENU screen
FF/REW
REM FF/REW MODE
REMOTE CONTROL (DV SLAVE) screen
REMOTE MENU
MENU
REMOTE CONTROL SCREEN ( DV SLAVE )
DV(MASTER)
OFF
REMOTE SELECT
REC CONTROL
REM FF/REW MODE
00:00:00:00
EXIT
h
1
4
7
IN POINT
OUT POINT
00:10:00:00
REMOTE CONTROL (DV MASTER) screen
FF/REW
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
REMOTE CONTROL SCREEN ( DV MASTER )
00:00:00:00
EXIT
h
1
4
7
IN POINT
OUT POINT
00:10:00:00
Note
:
:
:
CHAPTER
MANUAL
TC INPUT
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
When pressing and holding the REC
button more than 2 seconds while the DVD
recorder is stopped, encoded output
images can be checked while the button
is being held.
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
000 min
FINALIZE
8.0 Mbps DISC REMAIN
BITRATE
ADJ
EDL LOAD
TC CANCEL
:
:
:
CHAPTER
MANUAL
TC INPUT
Note
000 min
FINALIZE
8.0 Mbps DISC REMAIN
BITRATE
TC SET
TC CANCEL
ADJ
When pressing and holding the REC
button more than 2 seconds while the DVD
recorder is stopped, encoded output
images can be checked while the button
is being held.
EDL LOAD
EDIT/END
63
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Synchronous Recording
Recording Video & Audio From a Non-Linear Editor (continued)
1. Registering the In Point, Out Point, and Chapter Marks
Editing Via the REMOTE CONTROL (DV SLAVE) Screen
A keyboard and mouse can be used as an alternative to the DVD recorder’s buttons when using the REMOTE CONTROL (DV
SLAVE) screen.
Use the keyboard to directly enter the In Point, Out Point, and chapter marks.
Registering chapter marks : In order to register chapter marks using the REMOTE CONTROL screen, it will first of all be necessary
to set CHAPTER CREATION from the RECORDER MENU (2/2) screen to MANUAL.If this parameter
is set to AUTO, chapter marks will be automatically setup at specific intervals. The current setting for
CHAPTER CREATION is indicated in this screen’s CHAPTER field.
Front panel
Keyboard
Mouse
:
:
:
Select using the cursor buttons (t, 8, 7, and 6), and confirm the selection using the SET button.
Select using the arrow keys (†, ©, √, and ∞), and confirm the selection using the Enter key.
Left click the required button.
*
Setting of the In Point, Out Point, and chapter points can only be carried out by keyboard input.
Procedure
q
In Point (start point for editing):
Set the time code (hours : minutes : seconds : frames) at
which recording is to be started.
OUT POINT (end point for editing):
Set the time code (hours: minutes: seconds: frames) of
the position to stop recording.
q Use the arrow keys (†, ©, ∞, and √) to select the point to be
registered (i.e., the In Point or Out Point), and then press the
Enter key.
REMOTE CONTROL SCREEN ( DV SLAVE )
EXIT
h
1
4
7
IN POINT
00:00:00:00
OUT POINT
00:10:00:00
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
w Select the TC INPUT button using the cursor keys and input a
time code (hours: minutes: seconds: frames) into the TC input
field using the keyboard.
Chapter list:
TC INPUT:
This displays the time
codes of chapter
marks. These time
codes are displayed as
relative values with
respect to the In Point.
● The In Point’s time
code is registered as
the first chapter point.
● A total of 98 chapters
can be setup.
This field is used to input
:
:
:
CHAPTER
MANUAL
w
TC INPUT
REMOTE CONTROL SCREEN ( DV SLAVE )
00:00:00:00
OUT POINT
00:10:00:00
time codes for the In
Point, Out Point, and
chapter marks from the
keyboard.
000 min
FINALIZE
8.0 Mbps DISC REMAIN
BITRATE
ADJ
EXIT
h
1
4
7
IN POINT
EDL LOAD
e Press the Enter key.
TC CANCEL
● The time code will be registered for the selected point.
● If both IN point and OUT point are not selected, the time code
will be registered as a chapter point
● When a time code is registered for a chapter mark, the chapter
list will be sorted from the smallest time-code values, and the
newly registered point will be highlighted.
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
DISC REMAIN:
w
:
:
:
CHAPTER
MANUAL
This field shows an
estimate of the remaining
space for recording on the
disc.
TC INPUT
000 min
FINALIZE
8.0 Mbps DISC REMAIN
BITRATE
ADJ
Note
EDL LOAD
● C
H
A
P
T
E
R
The framing mode will be matched to that used for time codes
on the connected device.When in the drop frame mode, a value
corrected automatically will be registered when inputting the
frame to drop. (U-model only)
TC CANCEL
CREATION from the
RECORDER [2/2]
MENU screen must
be set to MANUAL
for this to be possible.
FINALIZE:
This button is used to
finalize the disc.
Saving & Loading Time-Code Settings
ADJUST:
TC CANCEL : This button is used to remove setting values
This button can be
pressed to determine
the remaining disc time
based on the editing
time and also to set a
suitable bit rate. This
setting is then displayed
in the BIT RATE field.
for the In Point, Out Point, and chapter marks.
Once settings have been made, they can be saved on your BD-X200. Even if a different
screen is opened or the power is turned off, stored data can then be loaded by selecting
EDL LOAD from the REMOTE CONTROL screen and pressing the Set button.
● If CHAPTER CREATION from the RECORDER MENU (2/2) screen is set to AUTO, it will
not be possible to select EDL LOAD on the REMOTE CONTROL screen.
● Whenever an external edit list (EDL) is read or time-code registration is started without
performing EDL LOAD, the settings will be updated accordingly. As a result, even if EDL
LOAD is selected in such a case, the previous data will not be reloaded.
EDL LOAD
:
This button is used to load the most-recent
edit list. It can be used whenever CREATION
CHAPTER has been set to MANUAL.
REMOTE CONTROL SCREEN
(
DV SLAVE
)
EXIT
h
1
4
7
IN POINT 00:00:00:00
OUT POINT 00:10:00:00
CHAPTER:
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
The right-hand field indicates
the current setting for
CHAPTER CREATION from
the RECORDER MENU (2/2)
screen.
● When set to MANUAL,
chapter marks can be
registered in this screen’s
chapter list.
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
:
:
:
CHAPTER
MANUAL
TC INPUT
8.0 Mbps DISC REMAIN
000 min
FINALIZE
ADJ BITRATE
TC CANCEL
EDL LOAD
Refer to page 68 for more details regarding the loading of external EDL.
EDL LOAD
● When set to AUTO, the
DVD recorder’s chapter
auto-create function will set
chapters. In such a case, it
will not be possible to
register chapters using this
screen’s chapter list.
● Chapter marks are
inserted at GOP intervals
(i.e., 15 frames). It will not
be possible to insert
chapter marks that are
closer together than this
interval.
2. Deleting the In Point, Out Point, and Chapter Marks
q Use the cursor buttons (t, 8, 7, and 6) to select the point to
q
be deleted (i.e., the In Point, Out Point, or a chapter mark from
the chapter list), and then press the SET button.
w Use the cursor buttons (t, 8, 7, and 6) to select TC CANCEL
and press the SET button.
● The selected point (i.e., In Point, Out Point, or a chapter mark
from the chapter list) will be deleted.
REMOTE CONTROL SCREEN ( DV SLAVE )
00:00:00:00
OUT POINT 00:10:00:00
EXIT
h
1
4
7
IN POINT
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
:
:
:
CHAPTER
MANUAL
TC INPUT
● Whenever a chapter mark is deleted, the chapter list will be
sorted.
000 min
FINALIZE
8.0 Mbps DISC REMAIN
BITRATE
ADJ
EDL LOAD
TC CANCEL
w
65
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Synchronous Recording
In, Out & Chapter Points from External Edit Lists
When dubbing a tape edited using an external VCR or non-linear editor to a DVD, the edit list (or EDL) created during the editing
process can be used to automatically set the In Point, Out Point, and chapter marks.
3. Starting the Record Process
Notes
Ⅵ Use the non-linear editor to control the DVD recorder.
● Loading of external edit lists is possible when CHAPTER CREATION from the RECORDER [2/2] MENU screen is set to
MANUAL.
● The framing mode for time codes (i.e. drop or non-drop) will be matched to that of the edit list. (U-model only)
● Each recording will be stored on the disc as a single title.
● Recording of video and audio to the DVD will be carried out from the In Point to the Out Point with chapters being automatically
created as specified.
● In order to be read, the EDL must be of CSV or Sony9100 format.
● The priority sequence for loading is CSV † Sony9100 † internally-made EDL.
● Chapter marks are inserted at GOP intervals (i.e., 15 frames). It will not be possible to insert chapter marks that are closer
together than this interval.
Notes
● If no In Point has been set, recording will start in response to DV commands; however, since time codes are set for chapter
marks as relative values with respect to the In Point, chapters may not be created as intended. It is recommended, therefore,
that an In Point always be specified when chapters are to be created.
● When the chapter auto-create function is used, chapters will be created at specific intervals.
REMOTE CONTROL SCREEN
(
9PIN MASTER
)
Procedure
EXIT
h
1
4
7
IN POINT 00:00:00:00
OUT POINT 00:10:00:00
1. Transfer the external edit list to your BD-X200.
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
Setting the Optimum Bit Rate
:
:
:
2. Select EDL LOAD from the REMOTE CONTROL screen and press
CHAPTER
MANUAL
TC INPUT
000 min
FINALIZE
8.0 Mbps DISC REMAIN
ADJ BITRATE
the SET button.
ADJUST can be used to set the optimum bit rate (i.e., the amount of data per
second) for the remaining space on a disc based on the recording time (or duration)
between the In Point and the Out Point.
● DISC REMAIN displays an estimate of the available space for recording on the
current disc.
● BIT RATE displays the current bit-rate setting.
To set the bit rate that best suits the remaining disc capacity, select ADJUST and
then press the SET button.
REMOTE CONTROL SCREEN
(
DV SLAVE
)
TC SET
EDL LOAD
EDIT/END
EXIT
h
1
4
7
IN POINT 00:00:00:00
OUT POINT 00:10:00:00
TC CANCEL
● The In Point, Out Point, and chapter marks are set in accordance with the
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
EDL.
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
:
:
:
CHAPTER
MANUAL
TC INPUT
8.0 Mbps DISC REMAIN
000 min
FINALIZE
ADJ BITRATE
TC CANCEL
EDL LOAD
EDL LOAD
Ⅵ Example 1: Loading a CSV-format EDL
ADJUST
JVC CSV
IN POINT
00:00:00:00
REMOTE CONTROL SCREEN ( 9PIN MASTER )
01:00:00:00
00:10:00:00
00:20:00:00
00:30:00:00
00:40:00:00
00:50:00:00
OUT POINT
Chapter1
Chapter2
Chapter3
Chapter4
Chapter5
IN POINT
00:00:00:00
EXIT
h
1
4
7
OUT POINT
01:10:00:00
4. Ending the Record Process
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
00:10:00:00
00:40:00:00
2
5
8
00:20:00:00
00:50:00:00
3
6
9
00:30:00:00
:
:
:
:
:
:
Ⅵ If you intend to play the recorded disc on this DVD recorder or on another player,
select FINALIZE and press the SET button.
Once finalizing has been carried out, no addition recordings can be made on
the disc.
Ⅵ To remove the recorded disc from your BD-X200, press the OPEN/CLOSE button
on the front panel.
REMOTE CONTROL SCREEN
(
DV SLAVE
)
EXIT
h
1
4
7
IN POINT 00:00:00:00
OUT POINT 00:10:00:00
:
:
:
:
:
:
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
:
:
:
CHAPTER
BITRATE
MANUAL
TC INPUT
00:00:00:00
00:25:00:00
00:40:00:00
2
5
8
00:15:00:00
00:30:00:00
00:45:00:00
3
6
9
00:20:00:00
00:35:00:00
00:50:00:00
000 min
FINALIZE
8.0 Mbps DISC REMAIN
ADJ
:
:
:
CHAPTER
MANUAL
TC INPUT
8.0 Mbps DISC REMAIN
000 min
FINALIZE
ADJ BITRATE
TC CANCEL
TC SET
TC CANCEL
EDL LOAD
EDIT/END
● Line returns at the end of each line.
● Maximum of 98 chapter marks.
● Framing mode determined by the character in front
of the frame field. (U-model only)
Period (.) : Drop frames
EDL LOAD
EDL LOAD
Colon (:) : Non-drop frames
FINALIZE
Ⅵ Example 2: Loading a Sony9100-format EDL
Recorder-In and Recorder-Out time codes are read from the X-source andY-source rows, and these are then set as the
In Point, Out Point, and chapter marks for editing.
Set as the In Point
Set as chapter marks
EDIT
RECORDER-IN
RECORDER-OUT
REMOTE CONTROL SCREEN ( 9PIN MASTER )
00:00:00:00
OUT POINT
01:00:00:00
0001
0002
0002
0003
0004
0004
0005
0005
00:00:00:00
00:10:00:00
00:20:00:00
00:10:00:00
00:20:00:00
00:20:00:00
EXIT
h
1
4
7
IN POINT
00:30:00:00
00:40:00:00
00:40:00:00
00:50:00:00
00:50:05:00
00:40:00:00
00:50:00:00
00:50:00:00
01:00:00:00
01:00:00:00
:
m
:
s
:
f
h
:
m
:
s
:
f
h
:
m
:
s
:
f
00:10:00:00
00:40:00:00
2
5
8
00:20:00:00
00:50:00:00
3
6
9
00:30:00:00
00:50:05:00
:
:
:
:
:
:
:
:
:
:
:
:
Set as the
Out Point
CHAPTER
BITRATE
MANUAL
TC INPUT
000 min
FINALIZE
8.0 Mbps DISC REMAIN
ADJ
Already set
TC SET
TC CANCEL
EDL LOAD
EDIT/END
Set as a
chapter mark
EDL LOAD
67
68
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Dubbing
Recording Operations Using a DV Camera Trigger
Dubbing DVDs Using the LAN Terminal
By connecting a camera featuring a DV terminal to this DVD recorder, audio and video from the camera can be easily recorded to
a disc. In this type of situation, the DV camera’s trigger button is used to control the BD-X200.
Supported cameras: GY-DV5000 and GY-DV5001.
When the LAN terminal is used to join two BD-X200 DVD recorders via an Ethernet connection, audio and video from a sender
DVD can be dubbed onto a DVD on the receiver device.
Connected devices
:
One BD-X200 SENDER (used for playback of the master DVD)
One BD-X200 RECEIVER (used for DVD recording)
Signal Connections
Signal Connections
TV set or monitor
All connection and disconnection of cables should be carried out with the power turned off.
Ⅵ Direct connection of two BD-X200s
Connect an Ethernet cable between the LAN terminals of the sender and receiver devices.
A Category 5, cross-wired Ethernet cable should be used in this case.
AUDIO OUT
Rear panel
VIDEO OUT
VIDEO
LINE
AUDIO
IN
IN
OUT
INPUT
LEVEL
CH1
OUT
4dB
8dB
Sender BD-X200
Receiver BD-X200
Y/C
GY-DV5000
IN
VIDEO
LINE
AUDIO
IN
VIDEO
LINE
AUDIO
IN
IN
OUT
INPUT
LEVEL
CH1
IN
OUT
INPUT
LEVEL
CH1
OUT
OUT
4dB
8dB
4dB
8dB
CH2
REMOTE
DV IN/OUT
Y/C
Y/C
IN
IN
USB
LAN
SIGNAL
GND
CH2
CH2
DC 19V
OPEN
EDITSEARCH
MONITOR
REMOTE
REMOTE
FILTER
DV IN/OUT
DV IN/OUT
1
2
3200K
5600K
1
1
/
8
ND
64 ND
STATUS
.3 5600K
.4 5600K
/
SHUTTER
MENU
L
C
D
B
R
I
G
H
T
DISPLAY
USB
USB
LAN
LAN
SIGNAL
GND
SIGNAL
GND
AUDIO
LEVEL
PULL
DC 19V
DC 19V
OPEN
FRONT
REAR
AUTO IRIS
BACK
F
U
L
L
A
U
T
O
BLACK
LOLUX
CH-1
CH-2
CH-1
UDIO INPUT
UDIO SELECT
CH-1 CH-2
CH-2
MODE
A
A
L
STRETCH
NORMAL
COMPRESS
VTR
NORMAL
SPOT
L
A
UT
O
CAM
MANUAL
DV terminal
(video, audio, and control signals)
DV cables:
POWER
VTR
ON
OFF
DV IN/OUT terminal
LAN terminal
LAN terminal
CAT-5 cross-wired cable
VC-VDV204 (2 m, 4P-4P) from JVC
VC-VDV206 (2 m, 4P-6P) from JVC
● Connect the DV IN/OUT terminal on the rear of your BD-X200 to the DV terminal on the GY-DV5000 using a DV (IEEE1394)
cable. One of the commercially-available cables indicated above should be used for this purpose.
● Connect the DVD recorder’s VIDEO LINE OUT and AUDIO OUT terminals to the monitor’s video in and audio in terminals.
Setup Procedures
● Insert a recordable disc into your BD-X200.
Settings
GY-DV5000 : Set DV REC TRIGGER from the OTHERS MENU (1/2) screen to ON.
BD-X200
:
Set REMOTE SELECT from the REMOTE MENU screen to DV(TRIGGER).
Input will automatically be DV.
● The BD-X200 will adopt Slave mode. (It will not be possible to control recording
REMOTE MENU screen
operations from the DVD recorder.)
REMOTE MENU
MENU
Note
DV(TRIGGER)
OFF
REMOTE SELECT
REC CONTROL
Not compatible with the REPLICATION feature of BR-DV6000.
FF/REW
REM FF/REW MODE
Procedure
ⅥRecording on the BD-X200 will start and stop in response to operation of the trigger button on the GY-DV5000 or GY-DV5001.
When using, make sure triggers are at least 1 second apart.
*
69
70
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Dubbing
Dubbing DVDs Using the LAN Terminal (continued)
Network Settings
Dubbing
Use the following procedure to carry out network settings on both the sender and receiver devices.
Setup Procedures
1. Press the SET UP button to display the Setup Menu.
BUSY
Sender device
Receiver device : Insert a blank DVD.
:
Insert a finalized disc.
Cursor buttons
(6, 7, t and 8)
OPEN/CLOSE
2. Select NETWORK from the Setup Menu and then press the SET
button.
Procedure
● The NETWORK MENU screen will appear.
OPTION DV Y/C LINE
SET UP
Use the DUBBING screen to carry out the dubbing of DVDs.
DUBBING screen
SET UP button
3. Use the following parameters from the NETWORK MENU screen
SET
TOP
MENU
MENU
to make settings required for dubbing.
Ⅵ HOST NAME
1. Sender and receiver devices
1. 2.
DUBBING
Open the DUBBING screen on both the sender and receiver devices.
q Press the SET UP button to display the Main Setup menu.
w Use the 6 and 7 buttons to select DUBBING and then press the SET
button.
MENU
DVD
Use the 6 and 7 cursor buttons or the ∞ and √ arrow keys to select this
parameter, and then input the BD-X200’s network name using the USB
keyboard.
(Names may be up to 20 characters in length.)
Ⅵ IP ADDRESS, SUBNET MASK, and DEFAULT GATEWAY
Refer to the following table for more details regarding these parameters.
q Select the required parameter using the 6 and 7 cursor buttons or the
∞ and √ arrow keys.
w Select the digit to be set using the t and 8 cursor buttons or the †
and © arrow keys.
e Change the selected digit using the 6 and 7 cursor buttons or the ∞
and √ arrow keys.
SET button
†
DVD
EXECUTE
NETWORK MENU Screen
● The DUBBING screen will appear.
NETWORK MENU
MENU
2. Sender and receiver devices
bdx200
HOST NAME
IP ADDRESS SETTING
IP ADDRESS
SUBNET MASK
STATIC
192.168.0.2
On both the sender and receiver devices, set DVD † DVD from the
DUBBING screen to EXECUTE and press the SET button.
Sender device:
● Search for the receiver device. (☞ Page 73)
Receiver device:
255..255.255.0
192.168.0.254
2.
DVD † DVD dubbing screen
DEFAULT GATEWAY
Sender device
DVD
†
DVD
SENDER
● A confirmation box for the sender device’s IP address is displayed.
r Repeat steps w through e to make all of the required settings, and
then press the SET button or Enter key.
MAC ADDRESS
99.99.99.99.99
To end dubbing:
Sender device
RECEIVER Searching . . .
:
Select ABORT and press the SET button.
The normal screen display will return.
4. To return to the Setup Menu after all settings have been made,
select MENU from the NETWORK screen, and then press the SET
button or the ENTER key.
SENDER IP ADDRESS † 192:168:000:002
Setting example:
This value is different for each
device.
Receiver device : Press the SET UP button to return to the normal screen
ABORT
display.
IP ADDRESSS 192.168.100.xxx
SUBNET MASK 255.255.255.000
5. Press the SET UP button to return to the normal screen display.
3. Receiver device
Set the IP address for the sender device as follows.
Receiver device
All devices are set to the same network.
q Use the on-screen confirmation box to set the required IP address.
● The IP address of the currently-registered sender device will be displayed.
Press the SET button to use this IP address.
DVD
†
DVD
RECEIVER
SET SENDER IP ADDRESS
168 000 002
Parameter
Description
Default setting
w If setting a new sender-device IP address, set the IP address of the sender
device.
192
SET
HOST NAME
The parameter is used to enter the BD-X200’s network name using a keyboard.
(Names may be up to 20 characters in length.)
bdx200
● Use the t and 8 cursor buttons to select the digit to be changed.
● Press the cursor (6/7) buttons to set the value of the selected digit.
● Repeat the above for all digits, select SET using the 8/t buttons and
press the SET button.
● The sender-device IP address set using this dialog box will be registered
as the most up-to-date address on the receiver device.
RECEIVER IP ADDRESS † 192:168:000:003
IP ADDRESS
SETTING
This parameter cannot be set and is fixed in STATIC mode.
————
IP ADDRESS
Use this parameter to set the IP address. Make sure, however, that no two devices
on a single network share the same IP address.
192.168.000.002
255.255.255.000
192.168.000.254
3.
DVD
†
DVD
RECEIVER
SET SENDER IP ADDRESS
168 000 002
● When all of the necessary settings have
DVD
†
DVD
RECEIVER
SUBNET MASK
Use this parameter to set the subnet mask. Connected BD-X200s should have the
same network setting.
been made, the status of the sender device
will be displayed on the receiver device’s
monitor.
192
SET
Searching . . .
ABORT
DEAULT GATEWAY Use this parameter to set the gateway address. Connected BD-X200s should have
RECEIVER IP ADDRESS † 192:168:000:003
● This screen will not appear when setting
the sender device first.
the same address.
SENDER IP ADDRESS
†
192:168:000:002
IP address for the sender device
71
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
Setup Menu Configuration
The Setup Menu screen is displayed on both the monitor and LCD display. As shown below, this screen is used to access the
BD-X200’s setup menus.
DISC MENU Screen
DISC MENU
Sender device
4. Sender device
The sender device will begin searching for receiver devices.
● When connection has been completed, a dialog box for confirming the start
of dubbing will appear.
● The IP address of the identified receiver device will be displayed in the dialog
box for confirming the start of dubbing.
4.
INPUT SELECT MENU Screen
MENU
DVD
†
DVD
SENDER
FINALIZE
CANCEL
CANCEL
INPUT SELECT MENU
DISC ERASE
MENU
INPUT SELECT
LINE
RECEIVER Searching . . .
SENDER IP ADDRESS † 192:168:000:002
ABORT
5. Sender device
To proceed with dubbing, select EXECUTE in the confirmation box for
the start of dubbing and press the SET button.
● DVD to DVD dubbing will begin.
As dubbing is carried out, the state of progress will be displayed on the
monitor connected to each device in the form of a progress bar.
SYSTEM MENU Screen
SYSTEM MENU
PRESET STYLE MENU Screen
MENU
OFF
SETUP (U-model only)
TEST SIGNAL
5.
PRESET STYLE MENU
Confirmation box for the start of
dubbing
OFF
MENU
FACTORY SETTING
KEYBOARD STYLE
EDIT MENU
CANCEL
ENGLISH
TYPE1
1
STYLE
Notes
TITLE PATTERN
ENABLE
DVD
†
DVD
SENDER
● Dubbing will not be carried out if CANCEL is selected from the
confirmation box for the start of dubbing.
1
CHAPTER PATTERN
5
Hour 30 Min
TOTAL RECORDING TIME
DUBBING START
● When dubbing a complete disc, approximately 90 minutes will be
required to complete the process.
● Do not disconnect any cables during the dubbing process.
If cable are accidentally disconnected, both devices should be turned
off once and then restarted before subsequent use.
SENDER IP ADDRESS † 192:168:000:002
CANCEL
EXECUTE
RECEIVER IP ADDRESS † 192:168:000:003
RECORDER MENU (2/2) Screen
RECORDER MENU (1/2) Screen
Setup Top Menu
RECORDER MENU (2/2)
RECORDER MENU (1/2)
BACK
6. Dubbing proceeds to completion.
MENU
During Dubbing
DISC MENU
Y/C TERMINAL MODE
THUMBNAIL FORM
S1
MANUAL
CHAPTER CREATION
SET INTERVAL
When dubbing has ended, the display for the sender device returns to the
DUBBING screen.
NORMAL
INPUT SELECT
SYSTEM
Every05Min
DVD
†
DVD
SENDER
1,2ch † 1,2ch
BOTH
TOTAL CONTENTS TIME
ENCODE QUALITY (Mbps)
AUDIO ENCODE
AUDIO CHANNEL (DV)
AUDIO REC VOLUME MODE
DISC IN ACTION
NO USE
4.4
PRESET STYLE
RECORDER
REMOTE
Finalizing is performed automatically by the receiver device.
LPCM
MENU
TITLE END
AUTO
MENU
ASPECT
DUBBING
ABORT
DISPLAY
CLOCK ADJUST
DUBBING
To cancel dubbing:
If ABORT from the DUBBING screen is selected and confirmed, the
following confirmation box will be displayed.
NETWORK
EXIT
State of
progress
REMOTE MENU Screen
REMOTE MENU
● Select EXECUTE and then press the SET
button to cancel the dubbing process and
return to the DUBBING menu.
● Select CANCEL and press the SET button
to close the confirmation window without
canceling the dubbing process.
● If dubbing is canceled, the partially-
recorded DVD will no longer be usable.
MENU
DISPLAY MENU Screen
DVD
†
DVD
SENDER
9PIN(MASTER)
Receiver device
REMOTE SELECT
REC CONTROL
OFF
DISPLAY MENU
REM FF/REW MODE
FF/REW
DVD
†
DVD
RECEIVER
Aborting makes the media
RECIEVER disc cannot be re-used.
a
UNUSABLE
!
MENU
DISPLAY
ON
ON
TITLE/CHAPTER
RECORDER MODE
TIME/DATE
EXECUTE
CANCEL
DUBBING
ABORT
ON
TIME+DATE
REMAIN
ON
MM/DD/YY
DATE STYLE
(DD/MM/YY:
E-model only)
CLOCK ADJUST MENU Screen
CLOCK ADJUST MENU
MENU
04/12/04
10:00
DATE
TIME
DUBBING MENU screen
6.
DUBBING MENU Screen
DUBBING
MENU
DUBBING
MENU
DVD
DVD
†
DVD
EXECUTE
†
DVD
CANCEL
NETWORK MENU Screen
NETWORK MENU
MENU
bdx200
HOST NAME
IP ADDRESS SETTING
IP ADDRESS
STATIC
192.168.0.2
SUBNET MASK
255..255.255.0
192.168.0.254
DEFAULT GATEWAY
MAC ADDRESS
99.99.99.99.99
73
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
Setting the Setup Menu
Setup Menus
Settings made in the setup menus are stored in the BD-X200’s internal memory and will be retained even when the power is turned
off. It is also possible to return to default settings whenever so required.
In addition to the buttons on the front panel, a keyboard and mouse can also be used to perform operations on these menus. The
following section, however, will describe operations performed using the front panel buttons.
The following table identifies and describes the parameters that may be set using the Setup Menus.
Top half
:
:
Appearance on monitor screen
Appearance on LCD display
Bottom half
Keyboard : Select using the arrow keys (∞ and √), and confirm the selection using the Enter key.
Option
Description
Mouse
:
Left click the required item.
This button opens a menu that allows settings to be made for finalizing and other similar disc processes.
DISC MENU
Settings
BUSY
Cursor buttons
(6, 7, 8 and t)
DISC MENU
INPUT SELECT
INPUT SEL
SYSTEM
OPEN/CLOSE
Setup menu operations are carried out while monitoring the display on the monitor
connected to the VIDEO LINE OUT terminal. In addition, setup menu content also
appears on the LCD display.
This button opens a menu that allows input audio and video signals to be selected.
OPTION DV Y/C LINE
SET UP
Ⅵ Stop the DVD recorder.
SET UP button
1. Open the Setup Menu screen.
SET
This button opens a menu that allows settings to be made for the DVD recorder itself.
TOP
MENU
MENU
To do this, press the SET UP button
SYSTEM
SET button
2. Open the setup menu in which settings are to be modified.
q Use the 6 and 7 buttons to select the required screen.
w Press the SET button
This button opens a menu that allows settings to be made for title-menu and chapter-menu display styles.
PRESET STYLE
PRESET
Setup Menu
*
The EXIT option can be selected to return to the normal screen display.
DISC MENU
INPUT SELECT
SYSTEM
This buttons opens a RECORDER MENU screen containing two different pages of parameters.
The RECORDER MENU (1/2) screen allows settings to be made for the chapter creation method and the
encoding of audio and video.
3. Make the required settings in the setup menu.
q Use the 6 and 7 buttons to select the parameter to be set.
w Press the SET button
● A list of setting values will appear.
e Use the 6and 7 buttons to select the required value from the list and then
press the SET button.
● The setting value will be modified accordingly.
r Repeat steps q through e until all of the required settings have been
made.
RECORDER
RECORDER
PRESET STYLE
RECORDER
REMOTE
DISPLAY
The RECORDER MENU (2/2) screen allows the settings required for recording to be made.
CLOCK ADJUST
DUBBING
NETWORK
This button opens a menu that allows settings to be made for remote operations via the DVD recorder’s
RS-422A or DV terminal.In addition, this menu also allows indication of whether or not the REC CONTROL
panel is to be displayed.
REMOTE
REMOTE
DISPLAY
DISPLAY
CLOCK ADJUST
CLOCK
EXIT
RECORDER MENU (1/2) screen
This button opens a menu that allows settings to be made for the display of status and alarm information
on the TV or monitor screen.
RECORDER MENU (1/2)
Ⅵ To return to the Setup Menu, select MENU and press the SET button.
Ⅵ To move to the next menu screen, select the † button at the top of the current
screen and press the SET button.
Ⅵ To return to the original menu screen, select either MENU or BACK and press
the SET button.
MENU
MANUAL
CHAPTER CREATION
SET INTERVAL
Every05Min
NO USE
4.4
TOTAL CONTENTS TIME
ENCODE QUALITY (Mbps)
AUDIO ENCODE
This button opens a menu that allows setting of the internal clock’s date and time.
This button opens a menu that allows settings to be made for DVD dubbing.
This button opens a menu that allows network settings to be made for LAN terminal usage.
This button is selected to return to the normal screen display.
LPCM
AUTO
ASPECT
4. Use either of the following methods to return to the normal screen
DUBBING
DUB
display.
Press the SET UP button.
or
Select EXIT from the Setup Menu and press the SET button.
RECORDER MENU (1/2)
MENU
NETWORK
NETWORK
EXIT
CHAPTER CREATION
SET INTERVAL
MANUAL
AUTO
TOTAL CONTENTS TIME
ENCODE QUALITY (Mbps)
AUDIO ENCODE
4.4
LPCM
Setting list
Restoring to Default Settings
SYSTEM MENU screen
All settings from the various setup menus can be returned to the corresponding
default settings by setting FACTORY SETTING from the SYSTEM MENU screen
to EXECUTE and by then pressing the SET button.
SYSTEM MENU
MENU
OFF
TEST SIGNAL
EXECUTE
ENGLISH
ENABLE
FACTORY SETTING
KEYBOARD STYLE
EDIT MENU
5
Hour 30 Min
TOTAL RECORDING TIME
75
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
DISC MENU Screen
SYSTEM MENU Screen
The following table identifies and describes the parameters that may be set using the DISC MENU screen.
The following table identifies and describes the parameters that may be set using the SYSTEM MENU screen.
Top half
:
:
:
Appearance on monitor screen
Appearance on LCD display
Default setting
Top half
:
:
:
Appearance on monitor screen
Appearance on LCD display
Default setting
Bottom half
Bottom half
[
]
[
]
Parameter
Possible settings
Description
Parameter
Possible settings
Description
FINALIZE
[CANCEL]
EXECUTE
This parameter indicates whether or not the recorded disc is to be finalized. If a disc
recorded using this DVD recorder is to be played on a DVD player, it must first be
finalized. Once finalizing has been carried out, no addition recordings can be made
on the disc.
This parameter is used to indicate whether or not a setup signal is to be added to
analog video (i.e., composite or YC separate) during the recording process. The
actual setting depends on whether the input analog signal contains a setup signal.
SET UP
[OFF]
ON
(U-model only)
SETUP
OFF
:
This setting should be made when the input analog signal does not contain
a setup signal.
FINAL
[CAN]
EXE
CANCEL
EXECUTE
:
:
Finalizing is not to be carried out.
Finalizing is to be carried out.
[OFF]
ON
ON
:
This setting should be made when the input analog signal contains a setup
signal.
It will be necessary to close all titles on a disc before it can be finalized.
(U-model only)
TEST SIGNAL
*
A maximum of 20 minutes will be required to complete finalizing.
This parameter is used to indicate whether or not the color bar output by the DVD
recorder’s internal signal generator is to be displayed.
[OFF]
ON
DISC ERASE
ERASE
[CANCEL]
EXECUTE
This parameter indicates whether or not a DVD-RW (video mode) is to be erased.
CANCEL
EXECUTE
:
:
This disc is not to be erased.
This disc is to be erased. In this process, all recorded data is erased
from the disc, and it can then be recorded to as a new disc.
OFF
:
The color bar is not displayed and video from the VIDEO LINE IN terminal is
output to the monitor.
ON
:
The color bar is displayed. Use this setting when the color bar is to be
recorded.
[CAN]
EXE
TEST S
[OFF]
ON
This parameter is used to indicate whether or not all setup menu parameters are to
be returned to their default settings.
MENU
This button is used to return to the Setup Menu screen.
FACTORY
SETTING
[CANCEL]
EXECUTE
CANCEL
:
:
Default settings are not to be restored.
Default settings are to be restored.
EXECUTE
FACTRY
[CAN]
EXE
INPUT SELECT MENU screen
This parameter is set when using a USB keyboard, and its purpose is to indicate the
keyboard’s layout (or language) as one of the following.
KEYBOARD
STYLE
[ENGLISH]
FRENCH
ITALIAN
GERMAN
SPANISH
JAPANESE
The following table identifies and describes the parameters that may be set using the INPUT SELECT MENU screen.
ENGLISH
FRENCH
ITALIAN
GERMAN
SPANISH
JAPANESE
Note
Top half
Bottom half
]
:
:
:
Appearance on monitor screen
Appearance on LCD display
Default setting
[
KBOARD
[ENG]
FRN
ITL
GER
ESP
JPN
Parameter
Possible settings
Description
INPUT SELECT
INPUT
[LINE]
Y/C
DV
This parameter is used to select the audio and video input signals.
The system must be restarted after this parameter is changed.
LINE
Y/C
DV
:
:
:
The composite video signal from theVIDEO LINE IN terminal and the analog
audio signals from the AUDIO IN terminals are to be used.
TheYC separate signal from theY/C IN terminal and the analog audio signals
from the AUDIO IN terminals are to be used.
The digital video and audio signals from the DV IN/OUT terminal are to be
used.
EDIT MENU
EDIT
[ENABLE]
DISABLE
This parameter is used to indicate whether or not a screen for editing the title and
chapter menus is to be displayed when title closing or finalizing is performed.
[LINE]
YC
DV
*
The front-panel indicator corresponding to the type of input signal selected on this
screen will light up or start to flash.
ENABLE
:
The menu editing screen is to be displayed.
Upon title closing, the THUMBNAIL EDIT screen will be displayed for
the corresponding chapter menu. (☞ Page 47)
Upon finalizing, the TITLE MENU EDIT screen will be displayed for the
title menu. (☞ Page 53)
Setting of this parameter will not be possible when REMOTE SELECT from the
REMOTE MENU screen has been set to DV(MASTER), DV(SLAVE), or
DV(TRIGGER). DV signals will be used for input at these times
[ON]
OFF
DISABLE : The menu editing screen is not to be displayed.
MENU
This button is used to return to the Setup Menu screen.
TOTAL RECORDING TIME
—
—
This button displays the total time for recording and erasing operations.(xHour xxMin)
—
MENU
This button is used to retu4rn to the Setup Menu screen.
77
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
PRESET STYLE MENU screen
RECORDER MENU Screen
The following table identifies and describes the parameters that may be set using the PRESET STYLE MENU screen.
The following table identifies and describes the parameters that may be set using the RECORDER screen.
Top half
:
:
:
Appearance on monitor screen
Appearance on LCD display
Default setting
Top half
:
:
:
Appearance on monitor screen
Appearance on LCD display
Default setting
Bottom half
Bottom half
[
]
[
]
RECORDER MENU (1/2) screen
Parameter
Possible settings
Description
Parameter
CHAPTER
Possible settings
Description
STYLE
STYLE
[TYPE1]
TYPE2
TYPE3
TYPE4
TYPE5
TYPE6
TYPE7
TYPE8
This parameter is used to select one of the eight different display styles that have
been provided for title and chapter menus. (☞ Page 44)
[MANUAL]
AUTO
This parameter is used to indicate whether or not chapters are to be created
automatically at set intervals while recording.
MANUAL : Chapters are not to be created automatically.
Use this setting when chapters are to be set manually.
CREATION
CHAPTR
[MANU]
AUTO
AUTO
:
Chapters are to be created at set intervals during recording.
The SET INTERVAL parameter below is used to specify this interval.
SET INTERVAL
INTERV
Every01min
This parameter becomes active whenever CHAPTER CREATION has been set to
AUTO.
[T1]
T2
T3
T4
T5
T6
T7
T8
[Every05min]
It is used to set the time interval for automatic chapter creation and is set in units of
minutes.
Every59min
1
[5]
59
TITLE PATTERN
TITL P
[1] to 6
[1] to 6
[1] to 6
This parameter is used to open the TITLE PATTERN screen.
That screen can then be used to select a display pattern for the title menu.
TOTAL
CONTENTS TIME
[NO USE]
0:01
If you already know the duration of the video to be recorded, this parameter can be
set to the corresponding time to allow your BD-X200 to select the optimum encoding
bit rate.
(Make a setting in hours and minutes between 00:00 and 9:59.)
● If the recording time is set using this parameter, ENCODE QUALITY will be set
automatically, and this setting may not be modified manually.
● If this function is not to be used, set it to NO USE.
CHAPTER
PATTERN
This parameter is used to open the CHAPTER PATTERN screen.
That screen can then be used to select a display pattern for the chapter menus.
9:59
CNTENS
[000]
001
CHAP P
MENU
[1] to 6
When this setting is made, ENCODE QUALITY will be returned to its previous
setting.
959
This button is used to return to the Setup Menu screen.
ENCODE
QUALITY(Mbps)
[8.0]
This parameter can be set whenTOTAL CONTENTSTIME has been set to NO USE.
Specifically, it allows direct setting of the encoding bit rate (i.e., the amount of data per second).
Setting range
described on right. The actual setting range depends on the setting that has been made for AUDIO
ENCODE.
QUALITY
AUDIO ENCODE
A ENC
[8.0]
LPCM
DOLBY DIGITAL : 2.0 to 9.0 Mbps (in 0.2-Mbps steps)
MPEG 2.0 to 9.0 Mbps (in 0.2-Mbps steps) (E-model only)
:
4.0 to 7.8 Mbps (in 0.2-Mbps steps)
:
LPCM
This parameter is used to set the encoding format for audio data.
Linear PCM encoding (Non-compressed)
DOLBY DIGITAL : Dolby AC3 encoding (Compressed)
MPEG MPEG encoding (Compressed) (E-model only)
[DOLBY DIGITAL] LPCM
:
MPEG
:
LPCM
[DD]
MPEG
ASPECT
[AUTO]
4:3
LETTER BOX
SQUEEZE
The screen aspect distinction signal of recorded video is selected.
AUTO
:
Aspect distinction signal is recorded according to the screen aspect
ratio of the input video.
4:3
:
:
Constantly records aspect distinction signal of 4:3 aspect ratio.
Constantly records aspect distinction signal of letterbox video.
(Content at the top and bottom of the screen is blackened out.)
Constantly records aspect distinction signal of squeezed video.
(Content at the left and right of the screen is compressed.)
LETTER BOX
ASPECT
[AUTO]
4 3
LETT
SQUE
SQUEEZE
:
Note
Setting this item to LETTER BOX or SQUEEZE will not change the output image
during recording and is reflected only in the recording to the disc.
†
This button is used to display the RECORDER MENU (2/2) screen.
This button is used to return to the Setup Menu screen.
MENU
79
E-80
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
REMOTE MENU screen
The following table identifies and describes the parameters that may be set using the REMOTE MENU screen.
RECORDER MENU (2/2) screen
Top half
:
:
:
Appearance on monitor screen
Appearance on LCD display
Default setting
Bottom half
Parameter
Possible settings
Description
[
]
Y/C TERMINAL
MODE
S1
[S2]
This parameter is used to set the specification for the DVD recorder’s VIDEO Y/C
INPUT terminal in order to enable the recording of wide-screen discrimination signals.
Parameter
REMOTE SELECT
Possible settings
Description
S1
:
S1 terminal mode is to be adopted. A discrimination signal for normal video
with a 4:3 aspect ratio and squeezed video is to be recorded.
[OFF]
This parameter is used to select a method for controlling external devices connected
via the RS-422A REMOTE terminal or the DV IN/OUT terminal).
S2
:
S2 terminal mode is to be adopted. A discrimination signal for normal video
with a 4:3 aspect ratio, squeezed video, and letterbox video is to be recorded.
9PIN(MASTER)
DV(MASTER)
DV(SLAVE)
OFF
:
Control is not to be carried out via the RS-422A REMOTE terminal
or the DV IN/OUT terminal.This is the standard setting for normal
operation.
Y C TM
S1
[S2]
Squeezed video : 16:9 wide-screen content with the left and right sides
compressed for normal aspect screens.
DV(TRIGGER)
9PIN(MASTER): This setting is made when recording audio and video from a VCR
connected to the RS-422A REMOTE terminal. When selected,
the REMOTE CONTROL (9PIN MASTER) screen appears, and
this screen can be used to carry out recording operations.
Letterbox video
:
Content with the top and bottom of the screen blackened out.
THUMBNAIL
FORM
[NORMAL]
V CUT
H CUT
Thumbnail creation method for chapter and title menus during wide-signal recording
is selected.
NORMAL : The input signal is to be converted into thumbnails without modification.
If the input video has an aspect ratio of 4:3, the corresponding thumbnails
are also to have this aspect ratio.
DV(MASTER)
:
:
:
This setting is made when recording audio and video from a DV
camera or video connected to the DV IN/OUT terminal.
When selected, the REMOTE CONTROL (DV MASTER) screen
appears, and this screen can be used to carry out recording
operations.
This setting is made when recording audio and video from a non-
linear editor connected to the DV IN/OUT terminal.When selected,
the REMOTE CONTROL (DV SLAVE) screen appears.In addition,
the BD-X200 will become the slave device and will be controlled
by the non-linear editor.
V+H CUT
REMOTE
[OFF]
9PIN
DVM
DVS
DVT
V CUT
:
In this case, the top and bottom of the video content is to be removed to
form thumbnails.
DV(SLAVE)
THUMB
[NOR]
VCUT
HCUT
V+H
H CUT
:
In this case, the left and right of the video content is to be removed to
form thumbnails. (SQUEEZE)
V+H CUT : In this case, the top, bottom, left, and right of the video content is to be
removed to form thumbnails. (LETTER BOX)
DV(TRIGGER)
Note
This setting is made when the BD-X200 is connected to a DV
camera featuring a DV record triggering function, and it allows
this DVD recorder to record video from the camera in response to
operation of its trigger button.
AUDIO
CHANNEL (DV)
[1,2ch † 1,2ch]
3,4ch † 1,2ch
This parameter is to be set when recording an audio signal from the DV IN/OUT
terminal.
Specifically, it indicates whether the signals from channels 1 and 2 or from channels
3 and 4 are to be recorded. (Only available for 32 kHz)
1,2ch † 1,2ch : Channels 1 and 2 are to be recorded.
3,4ch † 3,4ch : Channels 3 and 4 are to be recorded.
DV CH
[1 2]
3 4
When setting this item to 9PIN (MASTER), DV (MASTER) or DV (SLAVE), the video
output image becomes the REMOTE CONTROL screen display.However, video input
can be checked by press and holding the REC button while DVD Recorder is stopped
and viewing the encode output.
AUDIO REC VOL.
MODE
[BOTH]
This parameter is used to select the method for adjustment of audio recording levels.
INDEPENDENCE Specifically, both channels can be adjusted while maintaining the same level, or
REC CONTROL
REC
[OFF]
ON
This parameter is used to indicate whether or not the REC CONTROL panel is to be
displayed on the monitor screen.
each channel can be adjusted independently.
VRMODE
[BOTH]
INDE
BOTH
:
Both channels are to be adjusted while maintaining the same
level.
ON
:
The REC CONTROL panel is to be displayed only when a recordable disc
has been inserted and the DVD recorder is in Stop, Recording, or Recording
Pause mode.
[OFF]
ON
INDEPENDENCE : Both channels are to be adjusted independently.
OFF
:
The REC CONTROL panel not to be displayed.
DISC IN ACTION
DISCIN
[MENU]
TITLE
This parameter is used to indicate the action to be taken when a completed (i.e.,
finalized) disc is inserted into this DVD recorder or another DVD player. In order to be
effective, this setting must be made during the recording process.
MENU : The title menu is to be displayed.
REM FF/REW
MODE
[FF/REW]
SEARCH
This parameter is used to select the command output via the RS-422A REMOTE
terminal or DV terminal when the FF or REW button is pressed on the REMOTE
CONTROL (9PIN MASTER/DV MASTER) screen.
[MENU]
TITL
TITLE
:
Playback of the main content is to begin.
SEARCH
[F R]
SEA
FF/REW
:
A FF or REW command is to be output accordingly.
SEARCH : A forward-search or reverse-search command is to be output accordingly.
TITLE END
TI END
[MENU]
REPEAT
This parameter is used to indicate the action to be taken when playback of a title on
a completed (i.e., finalized) disc has ended. In order to be effective, this setting must
be made during the recording process.
MENU
This button is used to return to the Setup Menu screen.
[MENU]
REPT
MENU
:
The title menu is to be displayed.
REPEAT : Playback is to be repeated within the current title.
BACK
This button is used to return to the RECORDER MENU (1/2) screen.
81
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
DISPLAY MENU screen
CLOCK ADJUST MENU screen
The following table identifies and describes the parameters that may be set using the DISPLAY screen.
The following table identifies and describes the parameters that may be set using the CLOCK ADJUST MENU screen.
Top half
:
:
:
Appearance on monitor screen
Appearance on LCD display
Default setting
Top half
:
:
:
Appearance on monitor screen
Appearance on LCD display
Default setting
Bottom half
Bottom half
[
]
[
]
Parameter
Possible settings
Description
Parameter
Possible settings
Description
DATE
DATE
TIME
TIME
MENU
This parameter is used to set the date.
DISPLAY
OFF
[ON]
This parameter is used to indicate whether or not status and alarm information is to
be displayed on the monitor screen.
OFF
ON
:
:
No such data is to be displayed on-screen.
Data is to be displayed on-screen.
For more details regarding date and
time settings, refer to page 27.
DISPLY
OFF
[ON]
This parameter is used to set the time.
When this parameter has been set to ON, the following parameters can be
used to indicate which types of status information will be displayed
TITLE/CHAPTER
TITLE
OFF
[ON]
This parameter is used to indicate whether or not the DVD’s title, chapter number,
and elapsed time are to be displayed on-screen during recording and playback.
This button is used to return to the Setup Menu screen.
OFF
ON
:
:
No such data is to be displayed on-screen.
This data is to be displayed on-screen. Note, however, that nothing will be
displayed when OFF has been set for the DISPLAY parameter.
OFF
[ON]
RECORDER
MODE
OFF
[ON]
This parameter is used to indicate whether or not the DVD recorder’s current status
is to be displayed on-screen.
DUBBING screen
OFF
ON
:
:
The status is not to be displayed on-screen.
The status is to be displayed on-screen. Note, however, that nothing will be
displayed when OFF has been set for the DISPLAY parameter.
The following table identifies and describes the parameters that may be set using the DUBBING screen.
MODE
OFF
[ON]
Top half
:
:
:
Appearance on monitor screen
Appearance on LCD display
Default setting
Bottom half
[
]
TIME/DATE
[OFF]
DATE
This parameter is used to indicate whether or not the current date and/or time are to
be displayed on-screen.
TIME
TIME+DATE
OFF
DATE
TIME
:
:
:
No such information is to be displayed on-screen.
Only the date is to be displayed.
Only the time is to be displayed.
Parameter
Possible settings
Description
DVD † DVD
[CANCEL]
EXECUTE
This parameter is to be selected to enable DVD-to-DVD dubbing via the LAN terminal.
Dubbing is not to be carried out.
EXECUTE : Dubbing is to be carried out.
CANCEL
:
TIME+DATE : Both date and time are to be displayed.
DATE
[OFF]
DATE
TIME
T+D
● When the DVD recorder is stopped or recording, data from the internal clock is
displayed. When playing a disc, the date and time of disc finalizing are displayed.
● Even if DATE, TIME, or DATE+TIME have been selected, nothing will be displayed
when OFF has been set for the DISPLAY parameter.
dub
[CAN]
EXE
(☞ Page 70)
MENU
This button is used to return to the Setup Menu screen.
This parameter is used to indicate whether or not the disc’s remaining time (in minutes)
is to be displayed on-screen.
REMAIN
REMAIN
[OFF]
ON
OFF
ON
:
:
No such data is to be displayed on-screen.
This data is to be displayed on-screen.
● During recording, the remaining space available for recording is displayed (in
minutes).
During playback, the time remaining in the current title is displayed.
● Nothing will be displayed when OFF has been set for the DISPLAY parameter.
Note
[OFF]
ON
The remaining space available for recording will depend on factors such as the number
of titles recorded and the data encoding method; accordingly, this value should be
treated as an estimate and not as an exact value.
DATE STYLE
DSTYLE
YY/MM/DD
This parameter is used to select the display style for dates.
[MM/DD/YY] (U model) YY/MM/DD : Dates are to be displayed in year, month, and day sequence.
[DD/MM/YY] (E model) MM/DD/YY : Dates are to be displayed in month, day, and year sequence.
DD/MM/YY : Dates are to be displayed in day, month, and year sequence.
YMD
[MDY] (U model)
[DMY] (E model)
MENU
This button is used to return to the Setup Menu screen.
83
84
Download from Www.Somanuals.com. All Manuals Search And Download.
NETWORK MENU Screen
The following table identifies and describes the parameters that may be set using the NETWORK MENU screen.
Top half
Bottom half
:
:
:
Appearance on monitor screen
Appearance on LCD display
Default setting
[
]
Parameter
Possible settings
Description
HOST NAME
HOST
bdx200
This parameter is used to enter the BD-X200’s network name using a keyboard.
(Names may be up to 20 characters in length.Alphanumerical characters and hyphen
(-))
IP ADDRESS
IP ADD
[192.168.0.2]
[255.255.255.0]
[192.168.0.254]
This parameter is used to set the IP address. It is important to ensure that no two
devices on a single network share the same IP address.
SUBNET MASK
SUBNET
This parameter is used to set the subnet mask. Connected BD-X200s should have
the same network setting.
DEFAULT
GATEWAY
This parameter is used to set the gateway address. Connected BD-X200s should
have the same address.
GATE
MENU
This button is used to return to the Setup Menu screen.
Others
Troubleshooting
Before requesting for repair, please check the following URL:
If problem persists, contact either the store where the BD-X200 was purchased or your nearest JVC authorized dealer.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
U
E
Others
Others
Specifications
Specifications
Recording format
Disc format
Recordable media : DVD-R For General Version 2.0
DVD-RW Version 1.1
:
:
DVD Video Version 1.1
ISO9660-compatible UDF
Ⅵ General
Recording format
Disc format
Recordable media : DVD-R For General Version 2.0
DVD-RW Version 1.1
:
:
DVD Video Version 1.1
ISO9660-compatible UDF
Ⅵ General
Network terminal
:
RJ-45 (Category5),
100 BASE-Tx
USB 1.1 × 2
19 V DC
31 W 1.63 A
4.5 kg (device only)
Network terminal
:
RJ-45 (Category5),
100 BASE-Tx
USB 1.1 × 2
19 V DC
31 W 1.63 A
4.5 kg (device only)
USB terminal
Power supply
Power consumption
Weight
:
:
:
:
:
USB terminal
Power supply
Power consumption
Weight
:
:
:
:
:
Recording signals
:
Must conform to DVD Video Format
Recording signals
:
Must conform to DVD Video Format
Ⅵ Video Signals
Line input
Y/C input
Ⅵ Video Signals
Line input
Y/C input
:
:
1.0 V(p-p), 75 Ω unbalanced
Y signal = 1.0 V(p-p), 75 Ω unbalanced
C signal = 0.286 V(p-p), 75 Ω unbalanced
1.0 V(p-p), 75 Ω unbalanced
ISO/IEC13818-2 (MPEG-2 video)
8 bit
:
:
1.0 V(p-p), 75 Ω unbalanced
Y signal = 1.0 V(p-p), 75 Ω unbalanced
C signal = 0.3 V(p-p), 75 Ω unbalanced
1.0 V(p-p), 75 Ω unbalanced
ISO/IEC13818-2 (MPEG-2 video)
8 bit
Dimensions
212 mm (w) × 352 mm (d) × 88 mm (h)
(not including feet and other protrusions)
Dimensions
212 mm (w) × 352 mm (d) × 88 mm (h)
(not including feet and other protrusions)
Permissible operating temperature : 5°C to 35°C
Permissible operating temperature : 5°C to 35°C
Line output
:
:
:
:
Line output
:
:
:
:
Permissible operating humidity
Permissible storage temperature
Permissible storage humidity
:
:
:
20 to 80% RH
–20°C to 60°C
5 to 80% RH
Permissible operating humidity
Permissible storage temperature
Permissible storage humidity
:
:
:
20 to 80% RH
–20°C to 60°C
5 to 80% RH
Encoding format
Quantization
Sampling rate
Encoding format
Quantization
Sampling rate
13.5 MHz
13.5 MHz
Ⅵ AC adapter section
Ⅵ AC adapter section
Ⅵ Audio Signals
Ⅵ Audio Signals
Input
:
:
AC 100 V to 240 V `, 50 Hz/60 Hz, 1.6A MAX
DC 19 V , 6.3 A
Input
:
:
AC 100 V to 240 V `, 50 Hz/60 Hz, 1.6A MAX
DC 19 V , 6.3 A
Line input
:
–8 dBs, 10 kΩ minimum, unbalanced
+4 dBs, high impedance, unbalanced
Line input
:
–8 dBs, 10 kΩ minimum, unbalanced
+4 dBs, high impedance, unbalanced
Output
Output
Ⅵ Accessories
Ⅵ Accessories
Line output
:
:
:
:
:
:
:
–8 dBs, 1 kΩ minimum, unbalanced
–20 dBFS
85 dB
Line output
:
:
:
:
:
:
:
–8 dBs, 1 kΩ minimum, unbalanced
–20 dBFS
85 dB
Standard level
Dynamic range
Recording format
Quantization
Sampling rate
Number of channels
AC adaptor ........................................................................... ×1
Power cord ........................................................................... ×1
Standard level
Dynamic range
Recording format
Quantization
Sampling rate
Number of channels
AC adaptor ........................................................................... ×1
Power cord ........................................................................... ×2
LPCM / DOLBY DIGITAL
LPCM / DOLBY DIGITAL / MPEG
16 bit
48 kHz
2
16 bit
48 kHz
2
Ⅵ DV Interface
Ⅵ DV Interface
I/O
:
IEEE1394
I/O
:
IEEE1394
Ⅵ External Dimensions (Unit: mm)
Ⅵ External Dimensions (Unit: mm)
1
N
Q
Q
B
Q B Q N 1
Q B Q N 1
Q B Q N 1
88
6.5
88
6.5
212
212
BUSY
BUSY
OPERATE
OPEN/CLOSE
OPERATE
OPEN/CLOSE
OPTION DV Y/C LINE
SET UP
OPTION DV Y/C LINE
SET UP
DVD RECORDER BD-X200
TITLE
DVD RECORDER BD-X200
CHAPTER
AUDIO
AUDIO
CHAPTER
TITLE
CH1
CH2
DOLBY DIGITAL
LPCMMPEG
CH1
CH2
DOLBY DIGITAL
LPCMMPEG
SET
SET
PHONES
REV
STOP
PLAY
FWD
PAUSE
REC
TOP
TOP
PHONES
REV
STOP
PLAY
FWD
PAUSE
REC
MENU
MENU
MENU
MENU
86
E-86
Download from Www.Somanuals.com. All Manuals Search And Download.
E
About the audio mode during DV input
When inputting Audio UNLOCK mode signals from the DV input, high harmonic signals modulated from the
audio source may be recorded as noise in rare cases. If this occurs, set the audio mode of the input source to
LOCK mode, or use the LINE input or YC input.
This unit can detect audio signals of UNLOCK mode during DV input. When UNLOCK mode is detected, the
unit displays:
This product uses partial third-party software.
For information concerning the software used, login via FTP by
inputting the following into the unit and view the readme.txt file:
User: anonymous
“DV A UNLOCK” on the unit LCD
“UNLOCKED AUDIO(DV)” on the screen
Password: None
(If the IP address of the unit is set to 192.168.0.2, FTP
the address bar of Internet Explorer.)
until recording is started.
(May also be displayed when playing back a blank tape.)
In order to achieve higher quality recording, setting the source of DV input to the LOCK mode is recommended.
* About audio LOCK/UNLOCK mode
For DV digital signals, synchronous relationship of video and audio signals is referred to as LOCK mode, and
asynchronous relationship of video and audio signals is referred to as UNLOCK mode.
In the case of DV, 44.1kHz mode is normally the UNLOCK mode.
For the 48 kHz and 32 kHz modes, settings differ depending on the inputting video device. Please check
instruction manual of the used.
LLT0056-001A
(BD-X200E)
87
Download from Www.Somanuals.com. All Manuals Search And Download.
|