PLASMA DISPLAY MONITOR
INSTRUCTIONS
GD-V422PCE
GD-V502PCE
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Notice
WARNING:
1) To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or
moisture.
Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set. (including on
shelves above, etc.)
2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified
service personnel.
3) Do not remove the earthing pin on the power plug. This apparatus is equipped with a three pin earthing-type
power plug. This plug will only fit an earthing-type power outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the earthing plug.
4) This is a class A product. In a domestic environment this product may cause radio interference in which case
you may be required to take adequate measures.
CAUTION
This appliance is intended for use in environments which are relatively free of electromagnetic fields.
Using this appliance near sources of strong electromagnetic fields or where electrical noise may overlap with the
input signals could cause the picture and sound to wobble or cause interference such as noise to appear.
To avoid the possibility of harm to this appliance, keep it away from sources of strong electromagnetic fields.
To prevent electric shock, ensure the grounding pin on the AC cord power plug is securely connected.
FOR UK ONLY
IMPORTANT: THE MOULDED PLUG
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse
is fitted in this plug. Shall the fuse need to be replaced, please ensure that the replacement fuse has a rating of
5 amps and that it is approved by ASTA or BSI to BS1362.
ASA
Check for the ASTA mark
or the BSI mark
on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local JVC Dealer.
If the fitted moulded plug is unsuitable for the socket outlet in your home, then the fuse shall be
removed and the plug cut off and disposed of safety. There is a danger of severe electrical shock if the
cut off plug is inserted into any 13 amp socket.
If a new plug is to be fitted, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-Yellow: Earth
Blue:
Brown:
Neutral
Live
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows.
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is
marked with the letter E or by the Earth symbol
or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which
is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug
which is marked with the letter L or coloured RED.
How to replace the fuse. Open the fuse compartment with a screwdriver and replace the fuse.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
WARNING
Setup
This Plasma Display is for use only with the following optional accessories. Use with any other type of optional
accessories may cause instability which could result in the possibility of injury.
(All of the following accessories are manufactured by JVC)
...................................................
Speakers
TS-C422SPG (GD-V422PCE)
TS-C5001SPG (GD-V502PCE)
TS-C50P5G
IF-C50P2G
TS-C50P6G
•
.................................................
Stand Unit
•
•
•
•
•
.......................................
Video Input Card
Wall Mounting Unit
Wall Mounting Unit (angled)
....................................
......................
............................
TS-C50P2G
TS-C50P3G
Ceiling Suspension Unit
Always be sure to ask a qualified technician to carry out set-up.
Do not place the Plasma Display on sloped or unstable surfaces.
The Plasma Display may fall off or tip over.
•
Do not place any objects on top of the Plasma Display.
If water is spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result
in fire or electric shock. If any foreign objects get inside the Plasma Display, please consult your local JVC dealer.
•
If using the Stand Unit (optional accessory), leave a space of at least 10 cm at the top, left and right, at least 6
cm at the bottom, and at least 7 cm at the rear. If using some other setting-up method, leave a space of at least
10 cm at the top, bottom, left and right, and at least 1.9 cm at the rear.
Avoid installing this product near electronic equipment that is easy to receive electromagnetic waves.
It may cause interference in image, sound, etc. In particular, keep video equipment away from this product.
•
When using the Plasma Display
The Plasma Display is designed to operate on 220 - 240 V AC, 50Hz/60Hz.
Do not cover the ventilation holes.
Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display.
•
Do not stick any foreign objects into the Plasma Display.
Do not insert any metal or flammable objects into the ventilations holes or drop them onto the Plasma Display, as
doing so can cause fire or electric shock.
•
Do not remove the cover or modify it in any way.
High voltages which can cause severe electric shocks are present inside the Plasma Display. For any inspection,
adjustment and repair work, please contact your local JVC dealer.
•
Securely insert the power cord plug as far as it will go.
If the plug is not fully inserted, heat may be generated which could cause fire. If the plug is damaged or the wall
socket plate is loose, they shall not be used.
•
Do not handle the power cord plug with wet hands.
Doing so may cause electric shocks.
•
Do not do anything that may damage the power cable. When disconnecting the power cable, pull on the plug
body, not the cable.
Do not damage the cable, make any modifications to it, place heavy objects on top of it, heat it, place it near any
hot objects, twist it, bend it excessively or pull it. To do so may cause fire and electric shock. If the power cable is
damaged, have it repaired at your local JVC dealer.
•
If the Plasma Display is not going to be used for any prolonged length of time, unplug the power cord plug
from the wall outlet.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
If problems occur during use
If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odour starts to come out
from the Plasma Display, immediately unplug the power cord plug from the wall outlet.
If you continue to use the Plasma Display in this condition, fire or electric shock could result. After checking that the
smoke has stopped, contact your local JVC dealer so that the necessary repairs can be made. Repairing the Plasma
Display yourself is extremely dangerous, and shall never be done.
•
If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet
becomes damages, disconnect the power cord plug immediately.
A short circuit may occur, which could cause fire. Contact your local JVC dealer for any repairs that need to be
made.
•
CAUTION
When using the Plasma Display
Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display.
Heated air comes out from the ventilation holes at the top of Plasma Display will be hot. Do not bring your hands
or face, or objects which cannot withstand heat, close to this port, otherwise burns or deformation could result.
•
Be sure to disconnect all cables before moving the Plasma Display.
If the Plasma Display is moved while some of the cables are still connected, the cables may become damaged,
and fire or electric shock could result.
•
Disconnect the power cord plug from the wall socket as a safety precaution before carrying out any cleaning.
Electric shocks can result if this is not done.
•
Clean the power cable regularly to prevent it becoming dusty.
If dust built up on the power cord plug, the resultant humidity can damage the insulation, which could result in fire.
Pull the power cord plug out from the wall outlet and wipe the mains lead with a dry cloth.
•
This Plasma Display radiates infrared rays, therefore it may affect other infrared communication equipment.
Install your infrared sensor in a place away from direct or reflected light from your Plasma Display.
Cleaning and maintenance
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning
cloth or a soft, lint-free cloth.
If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water to
which a small amount of neutral detergent has been added, and then wipe it evenly with a dry cloth of the same
type until the surface is dry.
•
Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may
become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner,
otherwise the quality of the surface may be adversely affected.
•
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been
added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.
•
Do not allow any detergent to come into direct contact with the surface of the Plasma Display.
If water droplets get inside the unit, operating problems may result.
•
Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the
cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods
in contact with articles made from rubber or PVC.
•
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Accessories Supply
Check that you have the accessories and items shown
Operating Instruction book
Remote Control
Transmitter
EUR646532
Batteries for the Remote
Control Transmitter
(2 × R6 Size)
Fixing bands
INPUT
SURROUND
VOL
N
R
PICTURE
SOUND
SET UP
ZOOM
GD-V422PCE
GD-V502PCE
MULTI
PIP
SWAP SELECT MOVE
PICTURE
POS. /SIZE
ASPECT
PC
OFF TIMER
PLASMA DISPLAY
AC cord
AC cord
Ferrite core
Ferrite core
(For UK only)
(small size) × 1
(large size) × 2
Remote Control Batteries
Requires two R6 batteries.
1. Turn the transmitter face down.
Press and slide off the battery
cover.
2. Install the batteries as shown in
3. Replace the cover and slide in
reverse until the lock snaps.
the battery compartment.
(Polarity + or – must match the
markings in the compartment.)
Two “R6” size
Helpful Hint:
For frequent remote control users, replace old batteries with
Alkaline batteries for longer life.
Precaution on battery use
Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.
Observe the following precaution:
1. Batteries shall always be replaced as a pair. Always use new batteries when replacing the old set.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
5. Battery replacement is necessary when remote control acts sporadically or stops operating the Plasma Display.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
When connecting the speakers, be sure to use only the optional accessory speakers.
Refer to the speaker’s Installation Manual for details on speaker installation.
1
2
(Example: GD-V422PCE)
Speakers (Optional accessories)
1
2
SPEAKERS
Terminals (L)
Note: Connect the power cord before combining with
accessories such as the Stand Unit. When
combining with accessories such as the Stand Unit,
be very careful not to pinch the power cord.
SPEAKERS
Terminals (R)
AC cord connection
(see page 12)
– AC cord fixing
1. Open the clamper.
2. Insert the AC cord and
close the clamper
securely.
3. Slide up the clamper and fix
the AC cord plug securely.
When loosen
the clamper:
AC cord
Clamper
Note: The power plug in the illustration may not be the type fitted to your set.
– Cable fixing bands Secure any excess cables with bands as required.
Pass the attached cable To secure cables connected to Terminals, wrap the cable fixing band around
fixing band through the them then pass the pointed end through the locking block, as shown in the
clip as shown in the figure.
figure.
While ensuring there is sufficient slack in cables to minimize stress
(especially in the power cord), firmly bind all cables with the supplied
fixing band.
To tighten:
To loosen:
Push the catch
Pull
Pull
2
1
Optional Video Input Card insert Slots (covered)
AUDIO
PC IN
SERIAL
SLOT3
SLOT1
SLOT2
Note:
From SERIAL terminal
on Computer
From EXTERNAL monitor terminal
on Computer (see page 8)
Insert the optional Video Input Cards before
combining the Plasma Display with the Stand Unit.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
PC Input Terminals connection
COMPUTER
AUDIO
PC IN
VOL
I
N
P
U
T
M
E
N
U
-
+
ENTER
R
G
-
STANDBY
POWER ON
Less than
Conversion adapter
(if necessary)
Ferrite core (large size)
15
3" /16
(supplied)
(10 cm)
mini D-sub 15p
RGB
PC cable
Less than
15
Ferrite core (small size)
(supplied)
3" /16
(10 cm)
Audio
Stereo plug
Connect a cable which matches
the audio output terminal on the computer.
Installing the ferrite core (Small size)
1
2
3
Open
Press the cable
through and close
Pull back the tabs
(in two places)
Installing the ferrite core (Large size)
1
2
3
Open
Press the cable
through and close
Pull back the tabs
(in two places)
Notes:
(1) Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical
scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
(2) The display resolution is a maximum of 768 × 768 dots (GD-V422PCE), 1,024 × 768 dots (GD-V502PCE) when
the aspect mode is set to “4:3”, and 1,024 × 768 dots (GD-V422PCE), 1,366 × 768 dots (GD-V502PCE) when the
aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show
fine detail with sufficient clarity.
(3) The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible,
you will need to make setting changes to the computer at the time of connection.
(4) Some PC models cannot be connected to the set.
(5) There is no need to use an adapter for computers with DOS/V compatible mini D-sub 15P terminal.
(6) The computer shown in the illustration is for example purposes only.
(7) Additional equipment and cables shown are not supplied with this set.
(8) Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified
frequency range.
(9) Component Input is possible with the pin 1, 2, 3 of the mini D-sub 15P Connector.
Signal Names for mini D-sub 15P Connector
Pin No.
Signal Name
R (PR/CR)
Pin No.
Signal Name
GND (Ground)
GND (Ground)
GND (Ground)
NC (not connected)
GND (Ground)
Pin No.
Signal Name
GND (Ground)
SDA
HD/SYNC
VD
11 12 13 14 15
10
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
6
7
8
9
G (Y)
B (PB/CB)
1
2
3
4
5
GND (Ground)
GND (Ground)
Pin Layout for PC Input
Terminal
SCL
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
SERIAL Terminals connection
The SERIAL terminal is used when the Plasma Display is controlled by a computer.
COMPUTER
6
7
8
9
1
2
3
4
5
Ferrite core
(large size)
(supplied)
RS-232C
Straight cable
SERIAL
Pin layout for RS-232C
Installing the ferrite core
(Large size)
Less than
D-sub 9p
15
Open
3" /16
(10 cm)
Notes:
(1) Use the RS-232C cable to connect the computer to the Plasma Display.
(2) The computer shown is for example purposes only.
(3) Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled
by a computer which is connected to this terminal.
The computer will require software which allows the sending and receiving of control data which satisfies the conditions
given below. Use a computer application such as programming language software. Refer to the documentation for the
computer application for details.
Communication parameters
Signal level
Synchronization method
Baud rate
RS-232C compliant
Asynchronous
9600 bps
None
RS-232C Conversion cable
D-sub 9-pin female
Details
R X D
T X D
2
3
5
•
Parity
GND
Character length
Stop bit
8 bits
Non use
4
1
6
9
1 bit
7
8
•
Flow control
Shorted
NC
Basic format for control data
Command
Command Parameter
The transmission of control data from the computer
starts with a STX signal, followed by the command,
the parameters, and lastly an ETX signal in that order.
If there are no parameters, then the parameter signal
does not need to be sent.
Control details
Power ON
PON
POF
AVL
None
None
Power OFF
Volume 00 - 63
Audio mute OFF
Audio mute ON
Input select (toggle)
Slot1 input
Slot2 input
Slot3 input
PC input
Screen mode select (toggle)
4 : 3
Zoom
16 : 9
Just
0**
1
None
SL1
AMT
IMS
STX
C1 C2 C3
:
P1 P2 P3 P4 P5
ETX
Colon Parameter(s) End
(1 - 5 bytes) (03h)
Start
(02h)
3-character
command (3 bytes)
SL2
SL3
PC1
Notes:
(1) If multiple commands are transmitted, be sure to
wait for the response for the first command to come
from this unit before sending the next command.
(2) If an incorrect command is sent by mistake, this
unit will send an “ER401” command back to the
computer.
DAM
None
NORM
ZOOM
FULL
JUST
SELF
Auto
With the power off, this display responds to PON command only.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Controls
INPUT MENU
-
VOL
+
ENTER
R - STANDBY
G
POWER ON
Enter / Aspect
button
(see page 14, 16)
Main Power
On / Off Switch
Remote control
sensor
MENU Screen ON / OFF
Each time the MENU button is pressed, the menu
screen will switch. (see page 14)
Power Indicator
The Power Indicator will light.
Power-OFF .. Indicator not illuminated (The unit
will still consume some power as long as the
power cord is still inserted into the wall outlet.)
Stand-by ......Red
•
Normal Viewing Picture Set up
Sound
Picture Pos./ Size
INPUT button
(INPUT1, INPUT2, INPUT3 and PC IN Selection)
•
•
•
Power-ON ........Green
DPMS ..............Orange (With PC input signal and
during operation of PC’s screensaver.)
(see page 13)
Volume Adjustment
Volume Up “ + ” Down “ – ”
C.A.T.S sensor
Plasma C.A.T.S (Contrast Automatic Tracking System)
Plasma C.A.T.S automatically senses the ambient light conditions and
adjusts the brightness and gradation accordingly, to optimise contrast.
(Effective when Picture mode is set to Auto.)
When the menu screen is displayed.
“ + ”: press to move the cursor up
“ – ”: press to move the cursor down
Status button
Press the “Status” button to display the current system status.
PC
4:3
1
Input label
Aspect mode (see page 16)
Off timer
1
2
3
2
N button
(see page 17-20)
The off timer indicator is displayed only when the
off timer has been set.
Off timer
90
3
PICTURE button
(see page 18)
MULTI PIP
MULTI
PIP
Each time pressing this button main picture and sub picture will be displayed as
follows bellow.
[Picture and Picture]
[Picture out Picture]
[Picture in Picture]
Main picture
Sub picture
Main picture
Sub picture Main picture
Sub picture
MULTI
PIP
MULTI
PIP
MULTI
PIP
Normal
Viewing
B
A
A
B
A
B
A B
B
SWAP
SWAP
SWAP
SWAP
Press to swap main
picture and sub picture.
B A
A
[Example]
Main picture label is bright
Sub picture label is bright
SELECT
Press the SELECT button.
SELECT
PC1
PC1
Under main picture and sub picture display,
select the picture which you would like to
change input modes.
VIDEO1
VIDEO1
A
A
B
B
Input modes switching is possible
INPUT
INPUT
Main picture label is changed Sub picture label is changed
Press to change input signal.
SURROUND
VIDEO2
VIDEO1
PC1
VIDEO3
VOL
A
C
N
R
B
D
ZOOM
MOVE
Picture is changed
Press the MOVE button.
Each time the location of the sub picture will be moved.
Notes: (1) This button is effective only in the picture in picture.
(2) The sub picture may be hidden by the on screen display, depending on its position.
Notes: (1) Sound output is from the main picture.
(2) Using this function to display picture in picture for the purpose of public display
or commercial gain may infringe on copyright laws.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Controls
Stand-by (ON / OFF) button
The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 12).
Press this button to turn the Plasma Display On, from Stanby mode. Press it again to turn the Plasma
Display Off to Stanby mode.
SURROUND button
On
Off
The benefits of surround sound are enormous. You can be
completely enveloped in sound; just as if you were at a
concert hall or cinema.
The surround setting switches on and off each time the
Surround
On
SURROUND button is pressed.
Note:
The surround settings are memorized separately for
each Sound mode (Normal, Auto).
INPUT button
INPUT1, INPUT2, INPUT3 and PC IN Selection)
(
Press to select INPUT1, INPUT2, INPUT3 and PC IN input
SLOTS sequentially. (see page 13)
Sound mute On / Off (see page 20)
INPUT
Volume Adjustment
SURROUND
Press the Volume Up “+” or Down “–” button to increase or
decrease the sound volume level.
VOL
R button (see page 14-15)
Press the R button to return to previous menu screen.
N
R
ACTION button
Press to make selections.
POSITION buttons
Digital Zoom (see page 21)
ZOOM
SOUND button (see page 20)
Press to adjust the SOUND.
MOVE
Press to access
Digital Zoom.
PICTURE
SOUND
SET UP
ZOOM
SET UP button
(see page 14-15)
This displays an enlargement
of the designated part of the
displayed image.
MULTI
PIP
SWAP
SELECT MOVE
PICTURE POS./ SIZE button
(see page 17)
PICTURE
POS. /SIZE
ASPECT
ASPECT button
Press to adjust the aspect.
(see page 16)
PC
OFF TIMER
OFF TIMER button
The Plasma Display can be preset to switch to stand-by after a
fixed period. The setting changes to 30 minutes, 60 minutes, 90
minutes and 0 minutes (off timer cancelled) each time the button is
pressed.
PLASMA DISPLAY
30
60
90
0
PC button
When three minutes remain, “Off timer 3” will flash.
The off timer is cancelled if a power interruption occurs.
Press the “PC” input mode selection button to select the
PC input mode.
This button is used to switch directly to PC input mode.
Note:
In 2 screen display, the same input mode cannot be selected for the main picture and sub picture.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Power On / Off and input signal selection
AC cord connection
Connecting the AC cord plug to the Plasma Display.
Fix the AC cord plug
securely to the Plasma
Display with the clamper.
(see page 7)
Power On / Off
Connecting the AC plug to the Wall Outlet
Note:
AC plug types vary between countries / regions.
Press the Main power switch on the Plasma Display to turn the
Plasma Display on: Power-On.
VOL
I
N
P
U
T
M
E
N
U
–
+
ENTER
R
G
-
STANDBY
P
O
W
E
R
O
N
Power Indicator: Green
If the power indicator is lit red, press the power button on the
remote control to turn the Plasma Display on.
R
G
-
STANDBY
POWER ON
Example: The screen below is displayed for a while after the Plasma
Display is turned on. (setting condition is an example.)
Remote Control
Sensor
Power Indicator
From the second time on, the below screen
is displayed for a while (setting condition is
an example).
When the Power is turned on for the first
time, the Language selection screen is
displayed.
OSD Language
g
(
)
En lish UK
Deutsch
Fran ais
Italiano
From the second time on, language
selection can be done from the setup
menu. (see page 13)
PC
4:3
p
Es a ol
(
)
ENGLISH US
Select the desired language using the
and keys and press the ACTION
button.
Select
Set
Press the
Plasma Display off.
Power Indicator: Red (standby)
button on the remote control to turn the
INPUT
SURROUND
VOL
Press the
button on the remote control to turn the
Plasma Display on.
Power Indicator: Green
Turn the power to the Plasma Display off by pressing the
Main power switch on the Plasma Display, when the
Plasma Display is on or in standby mode.
N
R
Note: During operation of the power management function, the power
indicator turns orange in the power off state.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Power On / Off and input signal selection
Select the input signal
INPUT
Press the INPUT button to select the input signal to be
played back from the equipment which has been
connected to the Plasma Display.
Select the input signals to be connected by installing the optional Video
Input Card.
Input signals will change as follows:
VOL
R
G
-
STANDBY
I
N
P
U
T
M
E
N
U
-
+
ENTER
POWER ON
INPUT1
INPUT2
INPUT3
PC IN
INPUT MENU
-
VOL
+
ENTER
Notes:
INPUT
(1) Input terminal will not be selected if the Video Input Card is not
installed into the SLOT.
SURROUND
(2) Select to match the signals from the source connected to the
component / RGB input terminals. (see page 30)
(3) In 2 screen display, the same input mode cannot be selected for
the main picture and sub picture.
VOL
Selecting the On-Screen Menu Language
SET UP
Press to display the Set Up menu.
Press to select the OSD Language.
INPUT
SURROUND
Press to select your
preferred language.
Setup
1/2
VOL
N
R
Component/RGB-in select
RGB
RGB1
Input label
Signal
Selectable languages
Screensaver
Power save
Off
On
Off
Standby save
Power management
OSD Language
PICTURE
MULTI
SOUND
SET UP
English(UK)
Deutsch
(
)
English UK
Français
Italiano
Español
ENGLISH(US)
.......
(Chinese)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Menu Displays
The MENU button on the unit can also
be pressed.
To Picture adjust menu
(see page 18)
Press to select.
1
INPUT MENU
–
VOL
+
ENTER
Picture
Normal
Normalise
Picture Mode
Contrast
Brightness
Colour
Normal
25
0
0
Each time the MENU button is pressed,
the menu screen will switch.
Tint
0
3
[ from the unit ]
Sharpness
White balance
Advanced settings
Normal
On
INPUT MENU
–
VOL
+
ENTER
Normal Viewing Picture Set up
Sound
Picture Pos./ Size
2
1
Press to select
“On”.
Press to enter
Advanced
settings.
Press to select.
1
2
INPUT
Press to access each adjust
screen.
SURROUND
VOL
To Advanced settings
(see page 18, 19)
N
R
Setup
1/2
Advanced settings
Component/RGB-in select
Normal
Normalise
RGB
RGB1
Black extension
Input level
0
0
0
0
0
0
Input label
Signal
W/B High
W/B High
W/B Low
W/B Low
Gamma
AGC
R
B
R
B
Screensaver
Power save
Standby save
Power management
OSD Language
PICTURE
SOUND
SET UP
ZOOM
Off
On
Off
2. 2
Off
MULTI
PIP
(
)
English UK
SWAP
SELECT MOVE
PICTURE
POS. /SIZE
ASPECT
To Sound adjust menu
(see page 20)
PC
OFF TIMER
Sound
Normal
Normalise
Sound Mode
Bass
Treble
Balance
Surround
Normal
Setup
2/2
PLASMA DISPLAY
0
0
0
Auto power off
Off
MULTI DISPLAY Setup
Set up TIMER
Off
PRESENT TIME Setup
To Picture Pos./ Size adjust menu (see page 17)
During “AV(S Video)” and
“Component” input signal.
During “RGB” and “PC” input
signal.
Picture Pos./Size
Picture Pos./Size
Normal
Normal
Normalise
Normalise
H-Pos
H-Size
V-Pos
V-Size
H-Pos
H-Size
V-Pos
V-Size
Clock Phase
14
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Menu Displays
[ from the unit ]
R
Press to
access each
adjust screen.
2
INPUT MENU
–
VOL
+
ENTER
Press the R button to return to
previous menu screen.
Press to return to previous
menu screen.
To Signal screen for AV(S Video)
(see page 30, 31)
To Signal screen for Component
(see page 31)
To Signal screen for RGB and
PC (see page 32)
[
]
[
]
Signal
AV
[
]
Signal
Sync
RGB
Signal
Component
Off
(
)
3D Y/C Filter NTSC
Colour system
Cinema reality
On
Auto
Off
H & V
Cinema reality
H
-
Freq.
31.5 kHz
60.0 Hz
V
-
Freq.
(
)
Aspect Auto 4:3
4 : 3
Note: “Signal” setup menu displays different setting condition for each input signals. (see page 13)
To setup Screensaver
(see page 24-26)
Press to select Start Time / Finish Time
(When Time Designation is selected).
Press to select Periodic Time / Operating Time
(When Interval is selected).
Screensaver
PRESENT TIME
10 : 00
Start
Function
Mode
Start Time
Finish Time
Side panel
White bar scroll
Time Designation
Screensaver
PRESENT TIME
10 : 00
0 : 00
0 : 00
High
Start
Function
Mode
Start Time
Finish Time
Side panel
Wobbling
Peak limit
Press to Setup.
White bar scroll
Time Designation
7 : 00
8 : 00
High
Off
Screensaver
PRESENT TIME
10 : 00
R
Start
Function
Mode
Periodic Time
Operating Time
Side panel
Off
White bar scroll
Interval
0 : 00
Screensaver
Press the R button to return
to “Screensaver” menu.
0 : 00
High
PRESENT TIME
10 : 00
Start
Function
Mode
Periodic Time
Operating Time
Side panel
Wobbling
White bar scroll
Interval
1 : 00
To setup Multidisplay screen
(see page 28)
0 : 15
High
Off
Off
MULTI DISPLAY Setup
Peak limit
MULTI DISPLAY Setup
Ratio
Location
On
A1
2
2
To Set up Timer selection
screen (see page 22, 23)
Press to select POWER ON
Time / POWER OFF Time.
Set up TIMER
PRESENT TIME
2 : 30
Set up TIMER
PRESENT TIME
POWER ON Function
POWER ON Time
POWER OFF Function
POWER OFF Time
Off
6 : 00
Off
2 : 30
Off
POWER ON Function
POWER ON Time
POWER OFF Function
POWER OFF Time
Press to Set up
POWER ON Time /
POWER OFF Time.
0 : 00
Off
23 : 15
0 : 00
To PRESENT TIME Setup
(see page 22)
Set up TIMER
R
PRESENT TIME
2 : 30
POWER ON Function
POWER ON Time
POWER OFF Function
POWER OFF Time
On
6 : 00
On
PRESENT TIME Setup
PRESENT TIME
Press the R button to return
to “Set up TIMER” menu.
10 : 00
Set
23 : 15
PRESENT TIME
10 : 00
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ASPECT Controls
The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema
format picture.
ASPECT button
The aspect mode changes each time the
ASPECT
4 : 3
Zoom
16 : 9
Just
INPUT
ASPECT button is pressed.
SURROUND
VOL
Auto
[from the unit]
N
R
INPUT MENU
–
VOL
+
ENTER
The aspect mode changes each time the ENTER
button is pressed.
PICTURE
SOUND
SET UP
MULTI
PIP
ZOOM
SELECT MOVE
SWAP
[During MULTI PIP Operations]
(1) Picture and Picture, Picture in Picture :
PICTURE
POS. /SIZE
4 : 3
16 : 9
ASPECT
PC
OFF TIMER
(2) Others
:
Aspect switching is not possible.
Notes:
PLASMA DISPLAY
(1) For PC signal input, the mode switches between “4:3”, “Zoom” and “16:9” only.
(2) For a 1125 (1080) / 60i · 50i · 24p · 24sF, 1250 (1080) / 50i, 750 (720) / 60p · 50p signal input during
“Component” and “RGB” input signal, the mode is set to “16:9” mode, and switching is not possible.
Auto can be selected only during Video signal input.
(3) The aspect mode is memorized separately for each input terminal (INPUT1, INPUT2, INPUT3 and PC IN).
Picture
Explanation
Mode
4 : 3
4
4:3 will display a 4:3 picture at its standard 4:3 size.
4 : 3
3
3
4
16
16
Zoom mode magnifies the central section of the
picture.
Zoom
Zoom
16 : 9
Just
9
9
4
4
16:9 will display the picture at its maximum size but
with slight elongation.
16 : 9
3
16
16
Just mode will display a 4:3 picture at its maximum
size but with aspect correction applied to the center
of the screen so that elongation is only apparent at
the left and right edges of the screen. The size of
the picture will depend on the original signal.
Just
3
9
9
4
The display will automatically become enlarged
(depending on the picture source), allowing you to
view the picture at its maximum size.
Auto
3
Note:
Auto mode is designed to automatically adjust the
aspect ratio to handle a mix of 16:9 and 4:3 program
material. Certain 4:3 program material, such as
stock market data screens, may occasionally cause
the image size to change unexpectedly. When
viewing such programs, it is recommended that the
ASPECT be set to 4:3.
For an elongated image
4
Image is expanded
Auto
Changes in accordance
with the Auto mode
setting (see page 31).
3
For a 4:3 image
Notes: (1) Do not allow the picture to be displayed in 4:3 mode for an extended period, as this can cause a permanent
after-image to remain on the Plasma Display Panel.
(2) Using this function to display a picture with the aspect ratio changed from the original for the purpose of
public display or commercial gain may infringe on copyright laws.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Picture Pos./ Size
Adjusting screen
INPUT
SURROUND
PICTURE
POS. /SIZE
1
VOL
N
R
Press to display the Picture Pos./ Size menu.
Press to select H-Pos / H-Size / V-Pos /
V-Size / Clock Phase.
2
PICTURE
SOUND
SET UP
MULTI
PIP
SWAP
SELECT MOVE
ASPECT
PICTURE
POS. /SIZE
PC
OFF TIMER
During “AV(S Video)” and
“Component” input signal.
During “RGB” and “PC”
input signal.
Notes:
PLASMA DISPLAY
Picture Pos./Size
Picture Pos./Size
(1) Adjustment details are
memorized separately for
different input signal
Normal
Normal
Normalise
Normalise
H-Pos
H-Size
V-Pos
H-Pos
H-Size
V-Pos
V-Size
formats (Adjustments for component
signals are memorized for 525 (480) / 60i
· 60p, 625 (575) / 50i · 50p, 1125 (1080) /
60i · 50i · 24p· 24sF, 1250 (1080) / 50i,
750 (720) / 60p · 50p each, and RGB /
PC signals are memorized for each
frequency.)
V-Size
Clock Phase
Press to adjust Pos./ Size.
3
(2) If a “Cue” or “Rew” signal from a VCR or
DVD player is received, the picture
position will shift up or down. This picture
position movement cannot be controlled
by the Picture Pos./ Size function.
R
Press to exit from adjust mode.
“ ”
“ ”
When the Position Left
button is pressed. When the Position Right
button is pressed.
“ ”
button is pressed.
H-Pos
H-Size
V-Pos
V-Size
“ ”
When the Position Left
button is pressed. When the Position Right
“ ”
“ ”
When the Position Left
When the Position Left
button is pressed. When the Position Right
button is pressed.
button is pressed.
“ ”
“ ”
When the Position Right
button is pressed.
“ ”
“ ”
button
Clock Phase
(RGB/PC in Mode)
Flickering and distortion can be eliminated by using the Position Left
to carry out adjustment.
or Right
Note: Using the size adjustment function to display a picture with the aspect ratio changed from the original for the
purpose of the public display or commercial gain may infringe on copyright laws.
Helpful Hint ( N /
Normalisation)
Normalise
While the Picture Pos./ Size display is active, if either the N button on the remote control is pressed at any time or the
(ACTION button) is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustments
PICTURE
1
Press to display the Picture menu.
Picture
Normal
Normalise
Picture Mode
Contrast
Normal
Select to adjust each item.
25
0
0
2
Brightness
Colour
Tint
Press to select the menu to adjust.
0
Sharpness
White balance
3
Normal
Off
Select the desired level by looking at the picture
behind the menu.
Advanced settings
Press the left or right button to switch between
modes.
Picture
Normal
Auto
Normal
Normalise
Picture Mode
Contrast
Brightness
Colour
Tint
Sharpness
White balance
Normal
25
0
0
0
3
Cinema
Dynamic
Auto
Automatically selects the mode that best suits the
brightness of the environment.
Normal
On
Advanced settings
Normal
For viewing in standard (evening lighting)
environments.
This menu selects the normal levels of
Brightness and Contrast.
Press to select “On”.
Dynamic
For viewing in brighter environments.
This menu selects higher than normal levels of
Press to enter
Advanced settings .
Brightness and Contrast
.
Advanced settings On
Enables fine picture adjustment at a
professional level (see next page).
Cinema
Ideal for movies.
Note:
Advanced settings
If you would like to change the picture and colour of
the selected Picture mode to something else, adjust
using the items in the Picture menu. (see next page)
Normal
Normalise
Black extension
Input level
W/B High R
W/B High B
W/B Low R
W/B Low B
Gamma
0
0
0
0
0
0
Press the left or right button to switch between
modes.
2. 2
Off
AGC
Normal
Cool
Warm
Advanced settings Off
Displays images with settings of the
Picture menu.
N
Normalise
Helpful Hint ( /
Normalisation)
While the “Picture” menu is displayed, if either the N button on the remote control is pressed at any time or the
(ACTION button) is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustments
Notes:
Item
Effect
Adjustments
(1) “Colour” and “Tint” settings cannot
be adjusted for “RGB” and “PC”
input signals.
(2) You can change the level of each
function (Contrast, Brightness,
Colour, Tint, Sharpness) for each
Picture menu.
(3) The setting details for normal,
dynamic and cinema respectively
are memorized separately for each
input mode (INPUT1, INPUT2,
INPUT3 and PC IN).
(4) The “Tint” setting can be adjusted
for NTSC signal only during “AV
(S Video)” input signal.
Selects the proper brightness and
density for the room.
Contrast
Less
Darker
Less
More
Adjusts for easier viewing of dark pictures
such as night scenes and black hair.
Brightness
Colour
Brighter
More
Adjusts colour saturation.
Tint
(NTSC only)
Adjust for nice skin colour.
Adjusts picture sharpness.
Reddish
Less
Greenish
More
Sharpness
Note:
In PICTURE, there is not a noticeable change even when contrast is increased with a bright picture or reduced with a
dark picture.
Advanced settings
Item
Effect
Details
Black
extension
Adjusts the dark shades of the image in gradation.
(This cannot be adjusted when the input signal is RGB or PC.)
Less
More
Input level
W / B High R
W / B High B
W / B Low R
W / B Low B
Gamma
Adjustment of parts which are extremely bright and hard to see.
Adjusts the white balance for light red areas.
Adjusts the white balance for light blue areas.
Adjusts the white balance for dark red areas.
Adjusts the white balance for dark blue areas.
Less
Less
More
More
Less
More
Less
Less
Down
More
More
Up
S Curve
2.0
2.2
2.5
AGC
Increases the brightness of dark signal automatically.
Off
On
Notes:
(1) Carry out “W / B” adjustment as follows.
A Adjust the white balance of the bright sections using the “W / B High R” and “W / B High B” settings.
B Adjust the white balance of the dark sections using the “W / B Low R” and “W / B Low B” settings.
C Repeat steps A and B to adjust.
Steps A and B affect each other’s settings, so repeat each step in turn to make the adjustment.
(2) The adjustment values are memorized separately for each input mode (INPUT1, INPUT2, INPUT3 and PC IN).
(3) The adjustment range values should be used as an adjustment reference.
N
Normalise
Helpful Hint ( /
Normalisation)
On the remote control unit, while the “Advanced settings” menu is displayed, if either the N button is pressed at any
time or the (ACTION button) is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Adjustment
SOUND
1
Press to display the Sound menu.
INPUT
SURROUND
Select to adjust each item.
2
VOL
Press to select the desired adjustment menu.
N
R
Select the desired level by listening to the sound.
PICTURE
SOUND
SET UP
ZOOM
MULTI
PIP
SWAP
SELECT MOVE
Bass
Adjusts low sounds
Sound
Emits the original sound.
Normal
Normal
Normalise
Sound Mode
Bass
Treble
Balance
Surround
Treble
Adjusts high sounds
Normal
Off
0
0
0
Balance
Adjusts left and right
Automatically controls
proper volume level.
Auto
volumes
Surround
Select On or Off
To end adjustments
•
R
Press the R button
Note:
Press the SURROUND button to directly turn the surround effect On and Off. (see page 11)
Bass, Treble and Surround settings are memorized separately for each Sound mode (Normal, Auto).
N
Normalise
Helpful Hint ( /
Normalisation)
While the “Sound” menu is displayed, if either the N button on the remote control is pressed at any time or the
(ACTION button) is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
Mute
Useful when answering the phone or receiving unexpected visitors.
Press this button to mute the sound.
Press again to reactivate sound. Sound is also reactivated when power is turned off
or volume level is changed.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Zoom
This displays an enlargement of the designated part of
the displayed image.
Display the “Operation Guide”.
1
ZOOM
MOVE
Exit
Press to access Digital Zoom.
1
The “Operation Guide” will be displayed.
SURROUND
button
• During Digital Zoom, only the following keys
can be operated.
INPUT
SURROUND
MUTE button
VOL
VOL button
N
R
INPUT MENU
–
VOL
+
ENTER
R - STANDBY
POWER ON
G
PICTURE
SOUND
SET UP
ZOOM
MULTI
PIP
SWAP
SELECT MOVE
PICTURE
POS. /SIZE
ASPECT
PC
OFF TIMER
OFF TIMER button
Select the area of the image to be enlarged.
2
3
Press on the enlargement location to select.
The cursor will move.
Exit
2
Select the magnification required for the enlarged display.
Each time this is pressed, the magnification factor changes.
This is shown in the image being displayed.
×1
×2
×3
Return to normal display (quit Digital Zoom).
4
R
Press to exit from the Digital Zoom.
Notes:
(1) When power goes OFF (including “Off Timer” operation), Digital Zoom terminates.
(2) The Digital Zoom function cannot be selected while in the following operation states:
• “Multi-screen” (MULTI DISPLAY). (see page 28)
• “Multi-viewer” (Picture in Picture, Picture out Picture, Picture and Picture) operation. (see page 10)
(3) While Digital Zoom is in operation, “Adjusting Picture Pos./ Size” cannot be used.
(4) For RGB / PC input signals, normal multi-display magnification is only available at the VGA, SVGA and XGA resolution.
(5) The Digital Zoom capability is functional for the following component signals:
525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 1125 (1080) / 60i · 50i · 24sF, 750 (720) / 60p · 50p, 1250 (1080) / 50i
(6) The Digital Zoom capability is functional for the following composite signals: NTSC, PAL, SECAM
(7) Using this function to display an enlarged picture for the purpose of public display or commercial gain may infringe
on copyright laws.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
PRESENT TIME Setup / Set up TIMER
The timer can switch the Plasma Display On or Off.
Before attempting Timer Set, confirm the PRESENT TIME and adjust if necessary.
Then set POWER ON Time / POWER OFF Time.
SET UP
1
Press to display the
Setup menu screen.
Setup
1/2
INPUT
Component/RGB-in select
SURROUND
RGB
RGB1
Input label
Press to select
Set up TIMER or
PRESENT TIME
Setup.
2
Signal
Screensaver
VOL
Power save
Standby save
Power management
OSD Language
Off
On
Off
N
R
(
)
English UK
Press to display
the Set up TIMER
screen or
PRESENT TIME
Setup screen.
Setup
2/2
PICTURE
SOUND
SET UP
Auto power off
Off
MULTI DISPLAY Setup
Set up TIMER
PRESENT TIME Setup
PRESENT TIME Setup
Display the PRESENT TIME Setup screen.
To set up PRESENT TIME, follow the procedure described below.
PRESENT TIME Setup
Press to select PRESENT TIME.
PRESENT TIME
1
0 : 00
Set
PRESENT TIME
0 : 00
Press to set up PRESENT TIME.
button: Forward
button: Back
Notes:
• Pressing
• Pressing
“ ” “ ”
“ ” “ ”
or
or
button once changes PRESENT TIME 1minute.
button continuously changes PRESENT TIME by 15 minutes.
PRESENT TIME Setup
Press to select Set.
PRESENT TIME
2
10 : 00
Set
PRESENT TIME
10 : 00
Press to store PRESENT TIME Setup.
Note:
Set cannot be selected unless PRESENT TIME is set.
SET UP
Press to exit from PRESENT TIME Setup.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PRESENT TIME Setup / Set up TIMER
Set up TIMER
Display the Set up TIMER screen.
Press to select
POWER ON Time / POWER OFF Time.
Set up TIMER
1
PRESENT TIME
2 : 30
Off
Press to set up
POWER ON Time / POWER OFF Time.
button: Forward
POWER ON Function
POWER ON Time
POWER OFF Function
POWER OFF Time
0 : 00
Off
0 : 00
button: Back
Notes:
• Pressing
• Pressing
“ ” “ ”
or
“ ” “ ”
or
button once changes POWER ON Time / POWER OFF Time 1minute.
button continuously changes POWER ON Time / POWER OFF Time by 15 minutes.
Press to select POWER ON Function /
Set up TIMER
2
POWER OFF Function.
PRESENT TIME
2 : 30
Press to select On.
POWER ON Function
POWER ON Time
On
6 : 00
On
POWER OFF Function
POWER OFF Time
23 : 15
R
3
Press twice to exit from Setup.
Note:
Timer function will not work unless “PRESENT TIME” is set.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Screensaver (For preventing after-images)
Do not display a still picture, especially in 4:3 mode, for any length of time.
If the display must remain on, a Screensaver should be used.
SET UP
1
Press to display the Setup menu screen.
Setup
1/2
Press to select the Screensaver.
Component/RGB-in select
2
RGB
RGB1
Input label
Signal
Screensaver
Power save
Standby save
Power management
Off
On
Off
(
)
OSD Language
English UK
Press to select the Screensaver screen.
Reversal / Scroll selection
Screensaver
PRESENT TIME
10 : 00
Start
Function
Mode
Start Time
Finish Time
Side panel
Wobbling
Peak limit
White bar scroll
Off
0 : 00
Press to select the Function.
3
4
0 : 00
High
Off
Press to select the desired function.
White bar scroll
Image Reversal
Off
White bar scroll : The white bar will scroll from left to right.
Image Reversal : Negative image will be displayed on the screen.
Screensaver
Mode selection
PRESENT TIME
10 : 00
Start
Function
Mode
Start Time
Finish Time
Side panel
Wobbling
Peak limit
Press to select the Mode.
White bar scroll
Off
0 : 00
0 : 00
High
Off
Press to select each mode items.
Off
Off
Interval : Operates when Periodic Time and Operating Time are setup and those
times arrive.
Time Designation : Operates when Start Time and Finish Time are setup and those
times arrive.
On : Operates when Start is selected and the
(ACTION) is pressed.
Start setting
Screensaver
PRESENT TIME
10 : 00
When the Mode is set to On, press to
select Start.
Start
Function
Mode
Start Time
Finish Time
Side panel
Wobbling
Peak limit
5
White bar scroll
On
0 : 00
0 : 00
High
Off
Off
Press to start Screensaver.
The menu screen will disappear and the Screensaver will be activated. To stop
R
the Screensaver under On, press the button.
Note: This function does not guarantee the complete prevention of permanent after-images. The potential for the
occurrence of permanent after-images is merely decreased.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Screensaver (For preventing after-images )
Setup of Screensaver Time
After selecting Time Designation or Interval, the relevant Time Setup will become available for selection and the
Operating Time may be set. (Time cannot be set when “Mode” is “on” or “off.”)
Screensaver
Screensaver
Screensaver
PRESENT TIME
PRESENT TIME
PRESENT TIME
10 : 00
10 : 00
10 : 00
Start
Function
Mode
Start Time
Finish Time
Side panel
Start
Function
Mode
Periodic Time
Operating Time
Side panel
Start
Function
Mode
Start Time
Finish Time
Side panel
White bar scroll
Time Designation
White bar scroll
Interval
0 : 00
White bar scroll
Off
0 : 00
0 : 00
0 : 00
High
0 : 00
High
0 : 00
High
Press to select Start Time / Finish Time
(When Time Designation is selected).
Press to select Periodic Time / Operating Time
(When Interval is selected).
Screensaver
PRESENT TIME
10 : 00
Start
Function
Mode
Start Time
Finish Time
Side panel
Wobbling
Peak limit
White bar scroll
Time Designation
Press to setup.
button: Forward
button: Back
7 : 00
8 : 00
High
Off
Notes:
• Pressing
“ ” “ ”
Off
or
button once changes the Time 1minutes.
[However, switching occurs every 15 minutes when Periodic Time is selected.]
“ ” “ ”
Screensaver
• Pressing
or
button continuously changes the Time by 15 minutes.
PRESENT TIME
10 : 00
Start
Function
Mode
Periodic Time
Operating Time
Side panel
Wobbling
Screensaver
Screensaver
White bar scroll
Interval
1 : 00
PRESENT TIME
PRESENT TIME
10 : 00
10 : 00
Start
Function
Mode
Periodic Time
Operating Time
Side panel
Start
Function
Mode
Start Time
Finish Time
Side panel
White bar scroll
Interval
0 : 00
White bar scroll
Time Designation
0 : 15
High
Off
Off
0 : 00
0 : 00
High
0 : 00
High
Peak limit
Note: Timer function will not work unless “PRESENT TIME” is set.
Reduces screen after-image
These functions prevent the occurrence of an “after-image” on the display when turned ON.
Wobbling: Automatically shifts the display image at a dot level pitch (therefore unnoticeable to the eye) over
time to prevent after image of sharper contour of image.
Peak Limit: Suppresses image contrast (peak brightness).
Setup
1/2
SET UP
1
2
Component/RGB-in select
Press to display the Setup menu screen.
RGB
RGB1
Input label
Press to select “Screensaver”.
Signal
Screensaver
Power save
Standby save
Power management
OSD Language
Off
On
Off
(
)
English UK
Screensaver
Start
Function
Mode
Start Time
Finish Time
Side panel
Wobbling
Peak limit
Press to display Screensaver menu.
PRESENT TIME
10 : 00
Press to select “Wobbling” or
“Peak limit”.
3
White bar scroll
Off
0 : 00
Press to select “On” or “Off”.
0 : 00
High
Off
Off
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Screensaver (For preventing after-images )
Side Panel Adjustment
side panel
Do not display a picture in 4:3 mode for an extended period,
as this can cause an after-image to remain on the side panels
either side of the display field.
To prevent the appearance of such an after-image, illuminate
the side panels.
4:3
Screen Display
after-images
This function may be applicable to the non-picture area.
Non picture area
A
B
Picture out Picture
Picture and Picture
To display the Screensaver screen.
(Refer to the previous page, operation guide steps 1 and 2)
1
2
Press to select the Side panel.
Screensaver
PRESENT TIME
10 : 00
Start
Function
Mode
Press to select Off, Low, Mid, High.
White bar scroll
Time Designation
Start Time
Finish Time
Side panel
Wobbling
Peak limit
0 : 00
0 : 00
High
Off
Off
Low
Mid
High
Off
R
3
Press to exit from Screensaver.
Notes:
• Setting the side panel to High mode for an extended period may result in occurrence of after-images.
• The side panels may flash (alternate black / white) depending on the picture being shown on the screen. In such
an occurrence, use the Cinema mode.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Reduces power consumption
• Power save:
When this function is turned On, luminous level of the plasma display is suppressed, so
power consumption is reduced.
• Standby save:
When this function is turned On, power consumption of the microcomputer is reduced during
power supply standby (see page 10, 11, 12), so standby power of the set is reduced.
• Power management: The unit power supply is turned On or Off depending on whether or not there is a signal
during PC input mode.
This function is enabled when it is turned On. (Only during input from PC (MiniD-sub) terminal)
• Auto power off:
Equipment power supply is turned Off when there is no signal.
When this is set to On, the power supply of the unit goes Off 10 minutes after the input
signals stop.
This function is effective for input signals except input from PC (Mini D-sub) terminal.
Press to select
“Power save”
“Standby save”
Setup
1/2
“Power management”
“Auto power off”.
Component/RGB-in select
RGB
RGB1
Input label
Signal
Screensaver
Power save
Standby save
Power management
OSD Language
Off
On
Off
Press to select “On” or “Off”.
On
Off
(
)
English UK
Setup
2/2
Auto power off
Off
MULTI DISPLAY Setup
Set up TIMER
PRESENT TIME Setup
SET UP
Press to exit from Setup.
Note:
“Power management” and “Auto power off” are effective during normal viewing (one picture screen) only.
Customizing the Input labels
This function can change the label of the Input signal to be displayed.
Setup
1/2
Press to select Input label.
Component/RGB-in select
RGB
Press to change the Input label.
RGB1
Input label
Signal
Screensaver
Power save
Standby save
Power management
OSD Language
Off
On
Off
(
)
English UK
Notes:
While selecting an Input signal through Optional Video Input Card connected to Slot1 to Slot3, the Input label will
depend on each Optional Video Input Card.
Input labels for Slot1 to Slot3 and miniD-sub:
[Slot1 Input]
[Slot2 Input]
[Slot3 Input]
INPUT1/VIDEO1/COMPONENT1/RGB1/RGB1(digital)/PC1/DVD1/CATV1/VCR1/STB1
INPUT2/VIDEO2/COMPONENT2/RGB2/RGB2(digital)/PC2/DVD2/CATV2/VCR2/STB2
INPUT3/VIDEO3/COMPONENT3/RGB3/PC3/DVD3/CATV3/VCR3/STB3
[PC (MiniD-sub) input] PC/COMPONENT/RGB/DVD/STB
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup for MULTI DISPLAY
By lining up Plasma Displays in groups of 4 or 9 as illustrated below, an enlarged picture may be displayed across
all screens.
For this mode of operation, each plasma display has to be set up with a Display number to determine its location.
group of 4 (2×2)
group of 9 (3×3)
How to Setup MULTI DISPLAY
SET UP
1
Press to display the Setup menu screen.
Setup
1/2
INPUT
Component/RGB-in select
SURROUND
Press to select the
MULTI DISPLAY
Setup.
RGB
RGB1
Input label
2
3
VOL
Signal
Screensaver
Power save
Standby save
Power management
OSD Language
N
R
Off
On
Off
(
)
English UK
Press to display the
“MULTI DISPLAY
Setup” menu.
PICTURE
MULTI
SOUND
SET UP
Setup
2/2
Auto power off
Off
MULTI DISPLAY Setup
Set up TIMER
PRESENT TIME Setup
Press to select the
MULTI DISPLAY Setup.
MULTI DISPLAY Setup
MULTI DISPLAY Setup
Ratio
Location
On
A1
Press to select
“On” or “Off”.
2
2
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup for MULTI DISPLAY
How to set the display location number for each Plasma Display
Press to select Ratio (2nd step).
4
MULTI DISPLAY Setup
Press to select “2×2”, “3×3”.
MULTI DISPLAY Setup
Ratio
Location
On
A1
2
2
Press to select Location.
5
MULTI DISPLAY Setup
Press to select the required arrangement
number. (A1-C3 : Refer to the following)
MULTI DISPLAY Setup
Ratio
Location
On
A1
2
2
Display Number locations for each arrangement
( 2 × 2 )
( 3 × 3 )
A1
B1
C1
A2
A3
B3
C3
A1
B1
A2
B2
B2
C2
6
R
Press twice to exit from Setup.
Notes:
(1) For RGB / PC input signals, normal multi-display magnification is only available at the VGA, SVGA and XGA resolution.
(2) The multi-display capability is functional for the following component signals:
525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 1125 (1080) / 60i · 50i · 24sF, 750 (720) / 60p · 50p, 1250 (1080) / 50i
(3) The multi-display capability is functional for the following composite signals:
NTSC, PAL, SECAM
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup for Input Signals
Component / RGB-in Select
Select the input signals to be connected by installing the Optional Video Input Card.
(Refer to the Operating Instructions for the optional Video Input Card.)
Select to match the signals from the source connected to the Component / RGB input terminals.
Y, PB, PR signals
“Component”
R, G, B, HD, VD signals
“RGB”
1
2
SET UP
Press to display the Setup menu screen.
INPUT
SURROUND
VOL
Press to select the “Component / RGB-in
Select”.
Press to select the desired input signal.
N
R
Setup
1/2
Component/RGB-in select
RGB
RGB1
Input label
Signal
Screensaver
Power save
Standby save
Power management
OSD Language
Off
On
Off
PICTURE
SOUND
SET UP
ZOOM
MULTI
PIP
(
)
English UK
SWAP
SELECT MOVE
Component
RGB
R
Press to exit from adjust mode.
Note:
Selection may not be possible, depending on which optional board is installed.
3D Y / C Filter – For NTSC AV images
Select “Signal” from the “Setup” menu during AV(S Video) input signal.
(“Signal [AV]” menu is displayed.)
Setup
1/2
Component/RGB-in select
RGB
RGB1
Press to select the “3D Y / C Filter (NTSC)”.
Input label
Signal
Screensaver
Power save
Standby save
Power management
OSD Language
Off
On
Off
Press to set On / Off.
(
)
English UK
Press
(ACTION) button
R
[
]
Signal
AV
Press to exit from adjust mode.
(
)
3D Y/C Filter NTSC
Colour system
Cinema reality
On
Auto
Off
(
)
Aspect Auto 4:3
4 : 3
Note:
When On, this setting only affects NTSC input signals.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup for Input Signals
Colour system / Aspect Auto
Select Signal from the “Setup” menu during AV(S Video) input signal. (“Signal
[AV]” menu is displayed.)
Setup
1/2
Component/RGB-in select
RGB
RGB1
Input label
Press to select the “Colour System” or
“Aspect Auto”.
Signal
Screensaver
Power save
Standby save
Power management
OSD Language
Off
On
Off
Press to select each functions.
(
)
English UK
Press
(ACTION) button
If the picture image becomes unstable:
With the system set on Auto, under conditions of
low level or noisy input signals the image may in
rare cases become unstable. Should this occur, set
the system to match the format of the input signal.
[
]
Signal
AV
(
)
3D Y/C Filter NTSC
Colour system
Cinema reality
On
Auto
Off
(
)
Aspect Auto 4:3
4 : 3
Mode
Function
Colour system
Set the colour system to match that of the input signal.
If set to “Auto”, the colour system is automatically selected from “PAL”, “SECAM” and “NTSC”,
but not from “M-NTSC”. To view M-NTSC format pictures, you must manually set to “M-NTSC”.
Auto
PAL
SECAM
M.NTSC
NTSC
Aspect Auto
(4:3)
Set to “4 : 3” to view 4:3 images in an unchanged format when Aspect Auto is selected.
If you would like to view 4:3 images in Just format, set to “Just”.
Cinema reality
When on, the display attempts to reproduce a more natural interpretation of sources such as movie pictures, which are
recorded at 24 frames per second.
If the picture is not stable, turn the setting to off.
Setup
1/2
Select “Signal” from the “Setup” menu during AV(S Video) or Component
input signal.(“Signal [AV]” or “Signal [Component]” menu is displayed.)
Component/RGB-in select
RGB
RGB1
Input label
Signal
Press to select Cinema reality.
Press to set On / Off.
Screensaver
Power save
Standby save
Power management
OSD Language
Off
On
Off
(
)
English UK
Press
(ACTION) button
R
[
]
Signal
AV
Press to exit from adjust mode.
(
)
3D Y/C Filter NTSC
Colour system
Cinema reality
On
Auto
Off
(
)
Aspect Auto 4:3
4 : 3
Note:
When On, this setting only affects the following signal input:
[
]
Signal
Component
Off
• NTSC / PAL signal input during “AV(S Video)” input signal.
Cinema reality
• 525i(480i) 625i(575i) signal input during “Component” input signal.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup for input signals
Sync
Select Signal from the “Setup” menu during RGB input signal.
Setup
1/2
Press to adjust.
Component/RGB-in select
RGB
RGB1
Input label
Signal
Screensaver
Power save
Standby save
Power management
OSD Language
Off
On
Off
(
)
English UK
Press
(ACTION) button
R
[
]
Press to exit from adjust mode.
Signal
RGB
Sync
H & V
H
-
Freq.
31.5 kHz
60.0 Hz
V-
Freq.
Setting RGB sync signal:
Confirm that the input is set to RGB input (this setting is valid only for RGB input
signal).
Sync
Sync
Sync
H & V
on G
CS
H & V:
on G:
The H and V sync signals are input from the HD / VD connector.
Uses a synchronized signal on the Video G signal, which is input
from the G connector.
CS:
Uses a synchronized signal of Composite Sync input.
H-Freq. (kHz) / V-Freq. (Hz)
Displays the H (Horizontal) / V (Vertical) frequencies.
H
-
Freq.
kHz
31.5
60.0 Hz
This display is valid only for RGB input and PC input signals.
Display range:
V-
Freq.
Horizontal 15 - 110 kHz
Vertical
48 - 120 Hz
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Checks
Picture
Sound
Electrical Appliances
Cars / Motorcycles
Fluorescent light
Interference
Noisy Sound
Volume
(Check whether the mute function has been
activated on the remote control.)
Normal Picture
No Picture
No Picture
No Colour
No Sound
No Sound
Not plugged into AC outlet
Not switched on
Picture and Brightness / Volume setting
(Check by pressing the power switch or stand-
by button on the remote control.)
If a signal with a non-applicable colour system
format, or frequency is input, only the input
terminal indication is displayed.
Normal Sound
Normal Sound
Colour controls set at minimum level
(see page 18, 19)
Colour system (see page 31)
This Plasma Display uses special image processing. Hence a slight time lag may occur between image and audio,
depending on the type of input signal. However, this is not a malfunction.
Plasma Display panel
Symptoms
Check
The plasma display panel is manufactured using an extremely high level of precision
technology, however, sometimes some parts of the screen may be missing picture
elements or have luminous spots. This is not a malfunction.
Some parts of the screen
do not light up.
Do not allow a still picture to be displayed for an extended period, as this can cause
a permanent after-image to remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext
and images displayed in 4:3 mode.
Note:
The permanent after-image on the Plasma Display resulting from fixed image use
is not an operating defect and as such is not covered by the Warranty.
This product is not designed to display fixed images for extended periods of time.
After-images appear
Whirring sounds can be
heard from the display unit.
The display unit is fitted with a cooling fan to dissipate heat generated during normal
use.The whirring sound is caused by rotation of the fan and is not a malfunction.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Input signal can be displayed
Applicable input signals for PC Input (mini D-sub 15P) ( Mark)
∗
Horizontal
Vertical
When Multi Screen
and Digital Zoom
Signal name
Component RGB
frequency (kHz) frequency (Hz)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
525 (480) / 60i
525 (480) / 60p
625 (575) / 50i
625 (575) / 50p
750 (720) / 60p
15.73
31.47
15.63
31.25
45.00
37.50
33.75
28.13
27.00
27.00
31.25
31.47
31.47
35.00
37.50
37.88
46.88
53.67
49.73
48.36
56.48
60.02
68.68
68.68
63.98
79.98
91.15
75.00
59.94
59.94
50.00
50.00
60.00
50.00
59.94
50.00
24.00
48.00
50.00
70.00
59.94
66.67
75.00
60.32
75.00
85.06
74.55
60.00
70.07
75.03
85.00
75.06
60.02
75.03
85.02
60.00
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
750 (720) / 50p
1,125 (1,080) / 60i
1,125 (1,080) / 50i
1,125 (1,080) / 24p
1,125 (1,080) / 24sF
1,250 (1,080) / 50i
640 × 400 @70 Hz
640 × 480 @60 Hz
Macintosh13” (640 × 480)
640 × 480 @75 Hz
800 × 600 @60 Hz
800 × 600 @75 Hz
800 × 600 @85 Hz
Macintosh16” (832 × 624)
1,024 × 768 @60 Hz
1,024 × 768 @70 Hz
1,024 × 768 @75 Hz
1,024 × 768 @85 Hz
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
24 Macintosh21” (1,152 × 870)
25
26
27
28
1,280 × 1,024 @60 Hz
1,280 × 1,024 @75 Hz
1,280 × 1,024 @85 Hz
1,600 × 1,200 @60 Hz
Note:
Signals without above specification may not be displayed properly.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
GD-V422PCE
GD-V502PCE
220 - 240 V AC, 50Hz/60 Hz
Power Source
Power Consumption
Normal use
335W
445 W
Save off 1.9 W, Save on 1.1 W
0.4 W
Stand-by condition
Power off condition
Plasma Display panel
Drive method : AC type
42-inch, 16:9 aspect ratio
Drive method : AC type
50-inch, 16:9 aspect ratio
Contrast Ratio
3000:1
Screen size
920 mm (W) × 518 mm (H)
× 1,056 mm (diagonal)
786,432 (1,024 (W) × 768 (H))
[3,072 × 768 dots]
1,106 mm (W) × 622 mm (H)
× 1,269 mm (diagonal)
1,049,088 (1,366 (W) × 768 (H))
[4,098 × 768 dots]
(No.of pixels)
Operating condition
Temperatuer
0 °C - 40 °C
20 % - 80 %
Humidity
Applicable signals
NTSC, PAL, PAL60, SECAM, Modified NTSC
Colour System
525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 750 (720) / 60p · 50p, 1125 (1080) / 60i · 50i ·
24p · 24sF ···· SMPTE274M, 1250 (1080) / 50i
XGA display
Scanning format
PC signals
VGA, SVGA, XGA
SXGA, UXGA ···· (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals
(HIGH-DENSITY MINI D-SUB 15PIN) R,G,B/0.7 Vp-p (75-ohm)
Component
PC
Y
:
1.0 Vp-p (75-ohm : include sync)
0.35 Vp-p (75-ohm)
PB/CB :
PR/CR :
0.35 Vp-p (75-ohm)
HD, VD/1.0 - 5.0 Vp-p (high impedance)
0.5 Vrms (high impedance)
AUDIO IN (M3 JACK)
EXTERNAL CONTROL TERMINAL (D-SUB 9PIN)
RS-232C COMPATIBLE
SERIAL
SPEAKERS (6 Ω)
Accessories Supplied
Remote Control Transmitter
Batteries
16W [8 W + 8 W] (10 % THD)
EUR646532
2 × R6 Size
(TMME203 or TMME 187) × 2
Small size × 1, Large size × 2
Fixing bands
Ferrite core
Dimensions
1,020 mm × 610mm × 89mm
1,210 mm × 724mm × 95mm
(W × H × D)
95 mm
1,210 mm
89 mm
1,020 mm
VOL
I
N
P
U
T
M
E
N
U
–
+
ENTER
R
G
-
STANDBY
POWER ON
VOL
I
N
P
U
T
M
E
N
U
–
+
ENTER
R
G
-
STANDBY
POWER ON
Mass (weight)
main unit only
with speakers
approx. 29.5 kg net
approx. 33.7 kg
approx. 43.5 kg net
approx. 48.1 kg
Notes:
(1) Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.
(2) This equipment complies with the EMC standards listed below.
EN55022, EN61000-3-2, EN61000-3-3, EN61000-6-2.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
VICTOR COMPANY OF JAPAN, LIMITED
Printed in Japan
TQZW367-1
© 2004 VICTOR COMPANY OF JAPAN, LIMITED
Download from Www.Somanuals.com. All Manuals Search And Download.
|