JVC Computer Monitor DT E17L4G User Manual

MULTI FORMAT LCD MONITOR

DT-E21L4

DT-E17L4G

INSTRUCTIONS

The illustration of the monitor is of DT-E21L4.

For Customer Use:

Enter below the Serial No. which is located

on the rear of the cabinet. Retain this

information for future reference.

Model No.

Serial No.

: DT-E21L4 / DT-E17L4G

LCT2673-001A

Download from Www.Somanuals.com. All Manuals Search And Download.

Do not attempt to service this product yourself, as opening or

removing covers may expose you to dangerous voltages and

other hazards. Refer all service to qualified service personnel.

• The AC power supply is controlled by turning on/off the POWER

switch on the rear panel. If the product is installed in a place

where you cannot easily turn on/off the POWER switch, control

the AC power supply by plugging/unplugging the power cord

into/from the AC outlet. In this case, install the product as

close to the AC outlet as possible, and leave enough space for

plugging/unplugging the power cord. If the product is installed

in a place where you cannot easily plug/unplug the power

cord, equip an easily accessible device to the wiring of the

building for turning on/off the power.

Do not use the product for a long time if the sound is distorted.

Use only the power source specified on the unit.

• AC power: 120 V, 50 Hz/60 Hz

• DC power: 12 V — 17 V

• When the product is left unattended and unused for a long

period of time, unplug it from the wall outlet and disconnect

the cable system.

• Do not overload wall outlets, extension cords, or convenience

receptacles on other equipment as this can result in a risk of

fire or electric shock.

• Use only the accessory cord designed for this product to

prevent shock.

• Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the product and protect it from

overheating. These openings must not be blocked or covered.

• Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-circuit the parts,

which could result in a fire or electric shock.

• Never spill liquid of any kind on the product.

• Never place anything on the product. (Placing liquids, naked flames, cloths, paper, etc. on the product may cause a fire.)

• Do not apply any strong shock to the LCD panel. (Do not hit any object against it or push it with a sharp-pointed tool.)

• Do not put heavy objects on the product.

• Do not step on or hang on the product.

VESA mounting holes

WARNING

To prevent injury by accidental falll

Fix the monitor to a wall by using strings.

Fixing the monitor

Attach the hook (not provided) to the VESA mounting holes on the

rear panel (use the two holes on the upper side) using M4 x 10

mm screws (not provided). Bind the hooks on the rear panel of the

monitor to a wall or a pillar using durable string.

Hook and screw (M4 x 10 mm)

(not provided)

Hook (not provided)

The illustration of the monitor is of DT-E21L4.

FCC NOTICE

CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPARATUS TO RAIN OR

MOISTURE.

WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE

EARTHING CONNECTION.

CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH

THE SAME OR EQUIVALENT TYPE.

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Precautions (cont.)

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from

the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be

placed on the apparatus.

16) Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

17) When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries

must be followed strictly.

Operating Precautions

The LCD panel and backlight have life expectancy. Due to the basic characteristics of the LCD panel, an afterimage or uneven display

may occur. It is recommended that you change images occasionally, activate the power saving function, or often turn off the power to

reduce the load on the LCD panel. Continuous operations of the LCD panel may accelerate the deterioration.

Caution for use of the product for many hours

In the case that you use the monitor for many hours, we recommend that you set “No Sync Action” in “Sync Function” to “Power Save” in

Main Menu. This will reduce power consumption and relieve strain on the monitor. To reduce damage to the LCD panel, using the LCD

Saver function is recommended.

Caution for use of the product in the high temperature

Do not use the product in places of high temperature; otherwise, parts of this product or the LCD panel may be damaged. This product is

equipped with a temperature sensor to give warning if the temperature becomes too high. If the temperature exceeds the range of normal

use, “Temp. Over” is displayed, and the power is turned off automatically if the temperature becomes any higher. In this case, move the

product to a place of low temperature to let it cool down.

Maintenance

Unplug this product from the wall outlet before cleaning.

Screen

Cabinet

To avoid the deterioration or damages of the cabinet such as its

paint’s peeling away, be careful about the following:

● Do not wipe the cabinet using solvent such as alcohol, thinner,

or benzine.

● Do not expose the cabinet to any volatile substance such as

insecticides.

To avoid irreparable change in appearance of the screen such

as uneven color, discoloration, scratches, be careful about the

following:

● Do not paste or stick anything using any glues or adhesive

tapes.

● Do not write anything on the screen.

● Do not strike the screen with a hard object.

● Avoid condensation on the screen.

● Do not allow any rubber or plastic in contact for a long time.

● Do not wipe the cabinet forcefully.

● Do not wipe the screen with any liquid such as water. In

addition, wiping the screen with water-diluted neutral

detergent or solvent such as alcohol, thinner, or benzine may

affect the anti-reflection treatment of the screen.

● Do not wipe the screen forcefully.

Wipe stains off the cabinet with a soft cloth. If the cabinet gets

heavily stained, wipe it with a soft cloth soaked in water-diluted

neutral detergent and wrung well, then wipe with a soft dry cloth.

Ventilation openings

Wipe stains off the screen with a soft cloth. If the screen gets

heavily stained, wipe it with a soft cloth soaked in water-diluted

neutral detergent and wrung well, then wipe with a soft dry cloth.

Use a vacuum cleaner to get rid of the dust around the intakes (all

the openings). If a vacuum cleaner is not available, use a cloth and

wipe it off. Leaving the dust around the intakes may prevent proper

temperature control and cause damage to the product.

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

IMPORTANT SAFEGUARDS

Operating Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Caution for use of the product for many hours

Caution for use of the product in the high temperature

Maintenance

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Rear panel

Daily Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Front panel

Menu Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

The operation procedure

Menu Transition Diagram

Main Menu

Set-Up Menu

External Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

About the external control

Using the Make/Trigger system

Using the serial communication

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Self-check program

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

General

LCD panel

Input/output terminals

Dimensions

Available signals

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

● Do not rest your arm on the monitor or lean against the monitor.

● Do not touch the LCD panel when installing the monitor.

● Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor or injury.

● To install the monitor on a shelf or any other suitable

4 Adjust the position so that the screw holes on the stand support

align with right and left screw holes “C” and “E” on the bottom

surface using screws

You can install the monitor without protruding the stand bottom

plate by moving the stand bottom plate to the rear position.

plate, tighten the two stand screws on one side (four screws on

both sides), and finally retighten the temporarily set screws to lock

the stand support and the bottom plate.

CAUTION

Screw holes “C” and “E”

● Lay the monitor on a cloth with the LCD panel facing down to

prevent the LCD panel from being damaged.

● After moving the stand bottom plate to the rear position, be sure

to attach the stand with commercially available screws.

1 Loosen the stand screws on the stand support and remove the

bottom plate.

Bottom plate

5 Use no less than two commercially available screws (no less than

four screws on both sides) for the screw holes (10 – φ8) on the

stand bottom plate, to anchor the monitor. (Use screws having

enough holding strength and resistance against external force of

expected vibrations.)

Stand support

2 Temporarily set the stand screws to screw holes “3” on the right

and left sides of the stand support.

● Tighten the temporarily set stand screws so that they protrude

from the screw holes by about 4 mm.

Screw holes “3”

10 – φ8

3 Hook right and left recesses “A” onto the temporarily set screws in

the stand support.

Recesses “A”

CAUTION

● It is very dangerous not to anchor the stand with screws as

this may cause not only breakage due to the monitor falling or

dropping, but also injury or electrical shock.

● To install the stand

● To detach the stand

When attaching the stand to the monitor, insert the guides

of the stand into the guide holes on the monitor to place the

stand in the correct position. Then fix the stand firmly with the

attachment screws.

CAUTION

● Lay the monitor on a cloth with the LCD panel facing down to

prevent the LCD panel from being damaged.

Guide holes

Attachment screws

Screw holes for stand

Stand body

attachment

Guides

Monitor

Screw holes for

stand attachment

The illustration of the monitor

is of DT-E21L4.

Monitor

Stand support

Stand body

Download from Www.Somanuals.com. All Manuals Search And Download.

● To install the monitor on a wall

You can install the monitor on a wall by changing how the stand

bottom plate is attached.

Caution

● Consult authorized service personnel for electrical work. Using

power cords damaged during installation (i.e., exposed or severed

wiring) may result in fire or electric shock.

● Conduct the work with adequate working space. Damage or bodily

injury may result from working under unsuitable conditions.

● Avoid mounting this unit in areas where there is electrical wiring or

water pipes, as fire or electric shock may result.

Installation Only for Authorized Service Personnel

Consult authorized service personnel for the installation of this

unit.

Installation instructions must be followed precisely in order to

prevent accidents.

We are selling this product with the understanding that it will be

assembled and installed by properly trained and qualified service

personnel.

1 Lay the monitor on a cloth with the LCD panel facing down to

prevent the LCD panel from being damaged. Loosen the stand

screws on the stand support and remove the bottom plate.

About Accidents/Damages

We are not liable for any damage caused by faulty assembly, faulty

wall mounting, insecure wall mounting, misuse, alterations, or

natural disasters.

Bottom plate

● Please be aware that screw holes and anchor bolts will remain

in the wall surface if the monitor is removed after having been

mounted to the wall.

Long-term use of the LCD display monitor may result in

discoloration of the wall surface due to heat/air emitted by the

display.

Stand support

2 Temporarily set the stand screws in screw holes “2” and “4” on the

right and left sides of the stand support.

Danger

● Tighten the temporarily set stand screws so that they protrude

from the screw holes by about 4 mm.

● Consult authorized service personnel for the installation and

attachment of this unit to the wall. Do not attempt to mount the

unit by yourself.

Stand screws “2” and “4”

Improper assembly or installation may cause the unit to fall when

it is mounted, which may result in fatal accidents.

To prevent this happening, check the strength of the materials

in the mounting surface. Check the material strength again after

mounting as well.

Warning

● Using a monitor other than this product may result in damage or

bodily injury due to the LCD display monitor toppling over.

● Assemble all screws securely. Failure to do so may result in the LCD

monitor and stand falling down, potentially causing damage or

bodily injury.

3 Tighten commercially available screws in the 6 holes shown in the

figure below to install the monitor on the wall.

● This unit does not come with anchor bolts for securing it to walls,

etc. Be sure you have materials on hand as appropriate for the

mounting location.

● The monitor should be mounted to a wall that can adequately

hold the total weight of the monitor and stand over a long

period of time and which can adequately withstand earthquakes,

conceivable vibrations, and other external forces.

● Mounting On Wooden Walls

The weight of the unit should be borne by the wall posts or studs,

and these should be reinforced if insufficiently strong. Do not

install the Wall Mounting Unit on walls made of plasterboard or

thin plywood. Use the commercially sold screws best suited for the

wall structure and material.

4 Hook the temporarily set screws on the stand support in right

and left recesses “A” and “B” on the bottom plate, tighten the two

stand screws in right and left screw holes “D” and finally retighten

the temporarily set screws to lock the stand support and bottom

plate.

● Mounting On Concrete Walls

Recesses “A” and “B”

Use commercially sold wall anchors capable of supporting the

weight of the LCD monitor.

● Do not install the Wall Mounting Unit near the blower or air inlet of

an air conditioner.

● Do not install the Wall Mounting Unit in a location subject to

frequent vibration, impact or other external forces.

● Do not install the unit in a location where people may hang on it or

lean against it.

● Do not block the ventilation holes.

● Do not install the monitor on a non-vertical wall.

Screw holes “D”

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Rear panel

Carry handle

Use this handle when carrying the monitor.

The illustration of the

monitor is of DT-E21L4.

Security slot

Attach a security wire to this slot.

1 POWER switch

Turns AC power on or off.

● You need to press

button (☞ u on page 10) to use the monitor after turning on the POWER switch.

2 AC IN terminal

AC power input connector.

Connect the provided AC power cord to an AC outlet.

● Attach the provided power cord holder to prevent accidental disconnection of the AC power cord (☞ “Attaching the power cord holder”

on page 9).

CAUTION

Do not connect the power cord until all other connections are completed.

3 REMOTE terminal

Terminal for controlling the monitor by an external control (☞ “External Control” on page 22).

4 VIDEO terminals (BNC)

Input (IN) and output (OUT) terminals for the composite signals.

5 AUDIO (IN) terminals (pin jack, stereo minijack)

Input terminals for the analog audio signals.

● Use this terminal for the analog audio connection of the SDI. When a superimposed signal (EMBEDDED AUDIO signal on an SDI signal) is

input, analog audio signals cannot be input.

● Use these terminals when inputting HDMI analog audio signals.

● If there is no audio signal for HDMI (e.g. DVI signals have been changed to HDMI signals), input audio signals into this terminal. When

inputting audio into this terminal, set “Audio1 Assign” or “Audio2 Assign” of the menu to “HDMI-Analog”. (☞ page 16)

AUDIO (MONITOR OUT) terminals (pin jack)

Output terminals for the analog audio signal.

● The terminals emit the audio signals through the AUDIO (IN) terminal or EMBEDDED AUDIO signals through the E. AUDIO HD/SD SDI (IN 1

or IN 2) input terminal.

●The signal is output from this terminal only when the monitor is on or in “Power Save” (power save) mode (☞ “No Sync Action” on page 17).

● The EMBEDDED AUDIO signal...

–is decoded into an analog signal, then emitted.

–is emitted only when “SDI 1” or “SDI 2” is selected, and when EMBEDDED AUDIO signals come in to the E. AUDIO HD/SD SDI (IN 1 or IN 2)

terminal.

●Audio signals are only output from the HDMI terminal when the signals are not protected by HDCP.

–Even when the signals are protected by HDCP, sound is emitted from the speakers.

7 E. AUDIO HD/SD SDI (IN 1, IN 2) terminals (BNC)

Input terminals for the HD/SD SDI signals.

● The terminals accept also EMBEDDED AUDIO signals including up to 16 audio channels with a sampling frequency of 48 kHz.

Download from Www.Somanuals.com. All Manuals Search And Download.

8 E. AUDIO HD/SD SDI (SWITCHED OUT) terminal (BNC)

Output terminal for the HD/SD SDI signals.

● The SDI signals of the current input (SDI 1 or SDI 2) are re-clocked, then emitted.

● When an input other than SDI 1 and SDI 2 is selected, the SDI signal of the input selected last time is emitted from this terminal.

● The signals are emitted from this terminal only when the monitor is on or in “Power Save” (power save) mode.

9 HDMI terminal

Input terminal compatible with HDCP for the HDMI signal. (☞ page 29)

p COMPO./RGB terminal (mini D-sub 15pin)

Input terminal for the analog component signal or analog RGB signal.

● Set “Component/RGB Select” appropriately for input signals. (☞ page 15)

q DC switch

Turns the DC 12 V power on or off.

● You need to press

button (☞ u on page 10) on the front panel to turn on the monitor after turning on the DC switch.

● The monitor consumes the battery even while the monitor is on standby. To save battery life, turn off the DC switch.

w DC IN 12 V terminal

DC 12 V (maximum DC 17 V) power input connector.

When using DC 12 V power (maximum DC 17 V), check the DC IN 12V terminal pin signal, and use the correct polarity. If the polarity is

reversed, this could cause a fire or personal injury.

● While using both the AC and DC 12 V power supply, AC power supply is preferentially used. If the AC power supply is cut off (for example,

when turning off the POWER switch), the power supply automatically switches to the DC 12 V power supply.

● Use a DC power supply with the LPS (Limited Power Sources) function.

e Screw holes for external battery attachment

Attach external battery for DC 12 V power supply by using 2 screw holes. Choose the appropriate screw holes from 1, 2 or 3 according to the

type of external battery. (Depending on the battery type.)

Use the Anton Bauer Dionic 90 (mount: QR DXC-M3A) external battery.

CAUTION

● Do not use the external battery for DC 24 V power supply.

● Use only the battery specified above. If a heavy battery is used, it may fall off depending on the way the monitor is used.

Note for connections

• Before making any connections, turn off all the equipment.

• Use a cord whose plugs correctly match the terminals on this monitor and the equipment.

• Plugs should be firmly inserted; poor connections could cause noise.

• When unplugging a cord, be sure to grasp its plug and pull it out.

• DO NOT connect the power cord until all connections are complete.

• Refer also to the user manual of each piece of equipment.

Attaching the power cord holder

The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN terminal.

● The power cord holder consists of two parts, a case and a cover.

To detach the cover

Cover

AC IN terminal

Case

CAUTION

● Use only the provided screws.

● Make sure the plug will not be pulled out after the cover is attached to the case.

Download from Www.Somanuals.com. All Manuals Search And Download.

Daily Operations

Front panel

Tally lamp

This lamp is controlled by the tally function of the MAKE/TRIGGER

terminal.

• You can select the color of the tally lamp from “Green” or “Red.”

You can also select whether the whole lamp is turned on at once,

or whether it is turned on one half at a time. (☞ “Tally Setting” in

“Set-Up Menu” on page 17 and “External Control” on page 22)

• “No Effect” is displayed when you press a button which is not

available for the current input or signal format (the lamp lights

even when the function does not actually work).

• The items controlled by the MAKE system cannot be controlled

by the buttons on the front panel (“Remote On” is displayed

and the lamps do not light).

The illustration of the monitor is of DT-E21L4.

● This function does not work when “Area Marker” or “R-Area

Marker” is set to “Off” in “Marker.”

1 Speakers (stereo)

The speakers emit the same audio signal emitted from the AUDIO

(MONITOR OUT) terminals. (☞ “ 6 AUDIO terminals” on page 8)

q SAFETY MARKER button/lamp

Displays/hides the safety marker.

2 Picture adjustment knob

● Adjust the area of the safety marker in “Marker” of Main Menu

(☞ page 15).

● This function will not work when the picture is displayed in 1:1

aspect ratio and “SD 4:3 Size” on the menu is set to “H Full”.

● This function does not work when “Safety Marker” or “R-Safety

Marker” is set to “Off” in “Marker.”

PHASE:

Adjusts the picture hue.

Adjusts the picture color density.

Adjusts the picture brightness.

CHROMA:

BRIGHT:

CONTRAST: Adjusts the picture contrast.

● PHASE and CHROMA cannot be adjusted for certain signal

formats.

● When “Component Phase” is set to “Disable” and an NTSC signal

is input, PHASE can be adjusted (☞ page 18).

w SCREENS CHECK button/lamp

Displays only the selected element (R, G, or B) of the video signal.

● Each time you press this button, the picture changes in the

following order.

3 VOLUME adjustment button/EMBEDDED AUDIO setting

button

RGB (Normal screen)

Red screen

Green screen

Adjusts the volume when no menu screen is displayed.

Selects an audio channel when EMBEDDED AUDIO signals are

contained in SDI input. (☞ “Volume Adjustment/Audio Channel

Selection” on page 11)

Blue screen

e T.C. (time code) button/lamp

Activates/deactivates the display of the time data (time code)

contained in the SDI signal. (☞ “On the Information Display” on

page 11)

● Select the time code type in “Information” of Set-Up Menu (☞

page 19).

4 MUTING button

Turns off the sound when no menu screen is displayed.

●

To cancel the function, press the button again.

● Muting function is also canceled when “Balance” of “Audio

Setting” in the Main Menu is changed (☞ page 16).

r INPUT SELECT buttons/lamps

Selects an input.

buttons

SDI 1:

E. AUDIO HD/SD SDI (IN 1) terminal

E. AUDIO HD/SD SDI (IN 2) terminal

HDMI terminal

COMPO./RGB terminal

VIDEO terminal

When a menu screen is displayed selects or adjusts menu items.

(☞ “The operation procedure” on page 12)

SDI 2:

HDMI:

6 FUNCTION button

COMPO./RGB

Assign functions to the F1 and F2 buttons when the menu is not

displayed. (☞ page 21)

VIDEO:

● The lamp for the selected input lights.

7 MENU button

t F1/F2 buttons/lamps

You can use the functions assigned to this button.

y Power lamp

Activates/deactivates the display of the Main Menu. (☞ “The

operation procedure” on page 12)

8 COLOR OFF button/lamp

Unlit:

The monitor is completely off (the power switch

on the rear panel is turned off).

In Low Power Mode (☞ page 20)

Displays only the luminance signal.

● This function does not work for RGB input signals.

9 1:1 button/lamp

Lights in Green: The monitor is on.

Lights in orange: The monitor is off (on standby).

Flashes in orange: The monitor is in the Power Save (power save) mode.

Displays the picture in the original resolution of the input signal.

● The aspect ratio of the picture may change depending on the

input signal.

(☞

“No Sync Action” in “Sync Function” on page 17)

p AREA MARKER button/lamp

Displays/hides the area marker.

button

Turns on and off (on standby) the monitor.

● The power switch is equipped on the rear panel of the monitor

(☞ 1 on page 8).

● Select the style of the area marker in “Marker” of the Main Menu

(☞ page 15).

● This function works only when displaying the picture in 16:9

aspect ratio.

Download from Www.Somanuals.com. All Manuals Search And Download.

i DC lamp

When the DC 12 V power voltage is being lowered due to the battery consumption, the lamp changes to orange from green. When the

voltage becomes lower than a certain level, the monitor automatically turns off and the lamp turns to red.

● Make sure to turn off the POWER switch and DC switch on the rear panel before replacing the battery.

● The length of time that the lamp lights in orange differs depending on the type of battery or the battery condition. It is recommended to

replace the battery when the lamp turns to orange.

Volume Adjustment/Audio Channel Selection

Volume Adjustment

Volume screen

1 When no menu screen is not displayed, press

(volume adjustment button).

For SDI input the “Volume/Embedded Audio” screen appears. For any input other than SDI the “Volume”

screen appears.

9ROXPH

ꢄ

ꢀꢁꢂꢃ

ꢅ

2 Press to move the cursor to “Volume”.

(This step is skipped when the ”Volume/Embedded Audio” screen is not displayed.)

3 Press

to adjust the volume.

4 Press the MENU button to finish.

Volume/Embedded Audio screen

9ROXPHꢆ(PEHGGHGꢁ$XGLR

(The “Volume” screen disappears automatically if no operations are made for 5 seconds.)

(PEHGGHGꢁ$XGLRꢁ/ꢁFK

(PEHGGHGꢁ$XGLRꢁ5ꢁFK

9ROXPH

ꢀꢁꢂꢃꢅꢂꢇ

ꢀꢁꢂꢄꢈ*

ꢀꢁꢂꢃ

Audio Channel Selection

Select the audio channel output from the Speaker (L/R) and AUDIO (MONITOR OUT) (OUT1(L)/OUT2(R))

terminals when an EMBEDDED AUDIO signal is input during SDI input.

● It is necessary to set the audio channel group in advance. (☞ ”Embedded Audio Group” of “Audio Setting”

on page 16)

ꢄ

ꢅ

● Store the setting for each input of SDI 1 and SDI 2.

1 When the menu is not displayed, use the

The “Volume/Embedded Audio” screen appears.

● The “Volume/Embedded Audio” screen disappears automatically is no operations are made for about 30 seconds.

buttons

2 Use the

3 Use the

buttons to select the left and right channels (L ch/R ch)

buttons to select the audio channel

● Each time you press a button the audio channel changes according to the “Embedded Audio Group” setting. (☞ on page 16)

4 Press the MENU button

● The “Volume/Embedded Audio” screen disappears.

On the Information Display

The monitor displays the information below.

● Make the setting to display/hide each information using the MENU with the exception of 5,

controlled with T.C. button (☞ e on page 10).

1 Audio level meter

● You can check the conditions of the EMBEDDED AUDIO signals when “Level Meter Display” is set to “Horizontal” or “Vertical.”

● Not displayed when “Level Meter Display” is set to “Off.” (☞ “Audio Setting” on page 16)

2 Signal format

● Displayed when “Status Display” is set to “On.” (☞ “Information” on page 19)

● For the contents displayed, see “Available signals” on page 29 and “On the signal format” on page 12.

3 Source name assigned in “Character Setting”

● Displayed when “Source ID” is set to “On” or “Auto.”

● Displayed in large letters when “Status Display” is set to “Off” or “Auto.” (☞ “Information” on page 19)

4 CRC error indication

● Displayed when “CRC Error” is set to “On.” (☞ “Information” on page 19)

● A red square is displayed when an error occurs.

5 Time code

● When the input signal includes no time code, “TC – –:– –:– –:– –” is displayed (☞ e on page 10).

Download from Www.Somanuals.com. All Manuals Search And Download.

Daily Operations (cont.)

On the Status Display

If you press the INPUT SELECT button (☞ r on page 10) currently lit, the status of the input signal and setting of MUTING are displayed for about

3 seconds.

● Make the setting to display/hide the status in “Status Display” of the “Information” (☞ page 19).

● When “Status Display” is set to “Auto” or “On,” the status below is also displayed in the following cases:

– When you change the input

– When the signal condition of the current input changes

– When you turn on the monitor

● When “Status Display” is set to “On,” the signal format will remain displayed 3 seconds after the status is

displayed.

1 Signal format

● For the contents displayed, see “Available signals” on page 29 and “On the signal format” below.

On the signal format

The following messages appear depending on the type of input signals and their conditions.

When a HDMI signal protected with HDCP is input ➔ “*” (at the end of the indication)

When no video signal comes in

When a noncompliant video signal comes in

➔ “No Sync”

➔ “Out of range”

2 Signal format of HDMI and COMPO./RGB input

3 Setting of “MUTING”

• Only appears when in mute mode. (☞ 4 on page 10).

Menu Configuration

The operation procedure

Main Menu

0DLQꢁ0HQX

3LFWXUHꢁ)XQFWLRQ

6L]Hꢆ3RVLWLRQꢁ$GMXVW

$VSHFW

Set-Up Menu

6HWꢄ8Sꢁ0HQX

1 Press the MENU button to display the Main Menu

Selected item

)XQFWLRQꢁ6HWWLQJ

3LFWXUHꢁ6XEꢁ$GMXVW

:KLWHꢁ%DODQFHꢁ6HWWLQJ

5HPRWHꢁ6HWWLQJ

To display the Main Menu

➡ Press the MENU button.

6LJQDOꢁ6HWWLQJ

0DUNHU

,QIRUPDWLRQ

&RQWUROꢁ/RFN

/DQJXDJH

,0'

ꢀꢁ$OOꢁ/RFN

ꢀꢁ(QJOLVK

$XGLRꢁ6HWWLQJ

6\QFꢁ)XQFWLRQ

1Rꢁ2SHUDWLRQꢁ$FWLRQ ꢀꢁ2II

To display the Set-Up Menu

➡ Press the button while holding the button.

Operation

guide

DOOꢁUHVHW

Ex.: When “Picture Function”

in the Main Menu is selected

E^XijgZꢀ;jcXi^dc

2 Use the

buttons to select an item and press the button to

proceed to the next screen

BV^cꢀBZcj

E^XijgZꢀ;jcXi^dc

H^oZ$Edh^i^dcꢀ6Y_jhi

6heZXi

H^\cVaꢀHZii^c\

BVg`Zg

6jY^dꢀHZii^c\

7VX`a^\]i

/ꢀ"'%

/ꢀD[[

/ꢀꢀ%,

/ꢀCdgbVa

/ꢀ=VgY

/ꢀ'#'

6eZgijgZ

6eZgijgZꢀAZkZa

8I>

AI>

<VbbV

HncXꢀ;jcXi^dc

CdꢀDeZgVi^dcꢀ6Xi^dc /ꢀD[[

8dadgꢀIZbeZgVijgZ

hjWꢀbZcj

gZhZi

/ꢀ.(%%@

3 Use the buttons to select an item and press the button to

proceed to the next screen

● For some items, pressing the

buttons adjusts the setting.

4 Use the

buttons to select an item and use the

to adjust the setting

buttons

● The menu screen disappears automatically if no operations are

made for about 30 seconds.

● Inoperable menus will be grayed out.

● Some items will not be displayed on the menu depending on the

selected input and signal format.

5 Press the MENU button to finish operations

● Press the MENU button repeatedly until the menu screen disappears.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Transition Diagram

Main Menu

Backlight

Aperture

Aperture Level

CTI

Auto Adjust

H Size

Picture Function

H Position

V Size

Size/Position Adjust

LTI

V Postion

Dot Clock

Clock Phase

sub menu

reset

Gamma

Aspect

Color Temperature

sub menu

reset

Signal Setting

Marker

Component/RGB Select

Sampling Mode

Wide XGA

Auto Aspect

Manual Aspect

SD4：3 Size

SXGA/SXGA+

I/P Mode

Area Marker

Color System

sub menu

Audio Setting

Sync Function

No Operation Action

Marker Aspect

Safety Marker

Safety Area

reset

Frame

Balance

Level Meter Display

Horizontal Channel Arrange

Vertical Position

Horizontal Position

Meter Type

Center Marker

Line Brightness

R-Area Marker

R-Marker Aspect

R-Safety Marker

R-Safety Area

Audio1 Assign

Audio2 Assign

Embedded Audio Group

Level Meter Setting

Color

Reference Level

Over Level

Bar Brightness

Transparent

No Sync Action

Delay Time

Peak Hold

Low Latency

Set-Up Menu

Function Setting

Picture Sub Adjust

White Balance Setting

Remote Setting

Information

sub menu Position

Sync Term

Tally Setting

Tally Type

Tally Color

Contrast

Bright

Dimmer

Illumination

Chroma

Component Phase

Remote Active On Standby

LCD Saver

Phase

NTSC Setup

Component Level

sub menu

reset

Setting

Execute

Cancel

1st Start

Work Time

Contrast

Status

Backlight

OSD Contrast

Side Mask

reset

Color Temperature*

R Drive

Start After

Serial Type

Parallel Type

Pin1

G Drive

B Drive

R Cut Off

G Cut Off

B Cut Off

sub menu

reset

Control Lock

Language

Pin2

Pin3

Pin4

Pin5

Pin6

Pin7

IMD

Pin8

IMD Display

IMD Protocol

Address

Source ID

Character Setting

Status Display

Time Code

CRC Error

all reset

IMD Size

Text Color

Tally 1 Color

Tally 2 Color

Background Color

reset

Sub Hour Meter

Model

Version

Hour Meter

* : "Color Temperature" is only displayed, and cannot be set/changed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Configuration (cont.)

Main Menu

Picture Function

Setting for the picture quality.

Item

To do

Setting value

Backlight

Aperture*¹

Aperture Level*¹

CTI

LTI

Gamma

Adjusts the brightness of the display.

–20 to +20

Off, On

01 – 10

Off, Normal, Hard

2.2 (equivalent to Υ 2.2),

2.35 (equivalent to Υ 2.35),

2.45 (equivalent to Υ 2.45),

2.6 (equivalent to Υ 2.6)

9300K, 6500K, User

Activates/deactivates the function at the level set in “Aperture Level”.

Compensate the frequency response of the luminance signal of the video signal.

Adjust the clearness of the outlines of the chrominance signal.

Adjust the clearness of the outlines of the luminance signal.

Select the Gamma correction value.

Color Temperature

Select the color temperature.

sub menu

reset

Display the sub menu which enables you to adjust the items in “Picture Function” while viewing the actual picture.

Restore the default settings for all the items in “Picture Function”.

Memorized for each input.

Size/Position Adjust

Adjusts the size and position of the picture.

Item

To do

Setting value

Auto Adjust

H Size*¹

Activate/deactivate the function to adjust the optimized position for each input signal.

Adjust the horizontal picture size.

H Position*¹

V Size*¹

Adjust the horizontal picture position.

Setting value varies

depending on the signals.

Adjust the vertical picture size.

V Position*¹

Dot Clock*¹

Clock Phase*¹

sub menu

reset

Adjust the vertical picture position.

Adjust “Dot Clock” and “Clock Phase” alternately when the displayed picture becomes

unstable or streaked.

–32 to +32

Display the sub menu which enables you to adjust the items in “Size/Position Adjust” while viewing the actual picture.

Restore the default settings for all the items in “Size/Position Adjust”.

Memorized for each signal format.

Aspect

Sets the aspect ratio of the screen for displaying videos.

Item

Auto Aspect

To do

Setting value

Off, On

Select whether to adjust the aspect ratio (horizontal to vertical ratio of the screen) of the SD

signal automatically or manually (Manual Aspect).

Manual Aspect*¹

SD4:3 Size*¹

Sets the aspect ratio (horizontal to vertical ratio of the screen) of the SD signal.

Selects the picture size when the input signal format is 4:3.

16:9, 4:3

Normal

H Full

Matches the vertical picture size to the number of pixels.

Normal, H Full

Matches the horizontal picture size to the horizontal size of the screen. At

this time, the top and bottom of the picture are overscanned.

Not activate when picture is displayed in the 1:1 mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Signal Setting

Settings for input signals.

Item

To do

Setting value

Component/RGB Select

Selects the signal type you want to use for COMPO./RGB terminals.

Component, RGB

Sampling Mode

Analog RGB input

Standard: When the input signal is VGA60 or XGA60

Wide: When the input signal is WVGA60 or WXGA60

When the input signal is other than the above, the setting value does not affect the

displayed image.

Standard, Wide

Wide XGA

Select the analog WIDE XGA signal format.

1280*768, 1360*768

SXGA, SXGA+A

SXGA/SXGA+

Select the format when the analog SXGA60 signal comes in.

SXGA: Select this when the SXGA60 signal comes in.

SXGA+A: Select this when the SXGA+60/SXGA+60* signal comes in.

When the input signal is other than the above, the setting value does not affect the

displayed image.

I/P Mode*¹

Color System

Selects a proper mode corresponding to the input picture.

Select the color system.

Normal, Cinema, Field

• If the picture is unstable with “AUTO,” select the color system according to the input signal.

Auto, NTSC, PAL, SECAM,

NTSC 4.43, PAL M, PAL N,

PAL60

sub menu

reset

Display the sub menu which enables you to adjust the items in “Signal Setting” while viewing the actual picture.

Restore the default settings for all the items in “Signal Setting”.

When “Low Latency” on the menu is set to “On”, forcefully perform I/P conversion using “Field” processing.

Marker*

Settings for marker functions.

Item

1/2 Area Marker

To do

Setting value

Activate/deactivate the area marker and select the style of it.

The setting values and features are as follows.

Off, Line, Half, Half+Line

Off

Line

Half

Deactivate the marker.

Displays the area with an outline.

The area outside the specified aspect ratio of the screen is displayed at 50%

transparency.

Half+Line

The area of the specified aspect ratio of the screen is indicated by an outline,

and the area outside of that is displayed at 50% transparency.

Marker Aspect

Select the aspect ratio of the area marker.

4:3, 14:9, 13:9, 2.35:1, 1.85:1,

1.66:1

Safety Marker

Safety Area

Frame*³

Activate/deactivate the safety marker and select the style of it.*²

Adjust the area of the safety marker.

Off, Line, Half, Half+Line

80% – 100%

Displays/Hides the video area.

Off, On

Center Marker*³

Line Brightness

Displays/hides the marker indicating the center position of the picture.

Adjust the brightness of the marker.

Off, On

High, Low

Activate/deactivate the area marker and select the style of it.*²

2/2 R-Area Marker

R-Marker Aspect

Off, Line, Half, Half+Line

4:3, 14:9, 13:9, 2.35:1, 1.85:1,

1.66:1

Select the aspect ratio of the area marker.

Activate/deactivate the safety marker and select the style of it.*²

Adjust the area of the safety marker.

R-Safety Marker

R-Safety Area

Off, Line, Half, Half+Line

80% – 100%

● The area marker or the safety marker is displayed by using AREA MARKER or SAFETY MARKER button, or external control.

● Select either non-“R-” items or “R-” items to activate by using external control. (☞ “External Control” on page 22)

● When a picture is displayed in 4:3 aspect ratio, the safety marker for the 4:3 area is displayed.

● To display the safety marker for the area of a picture displayed in 16:9 aspect ratio, set Area Marker to "Off".

Memorized for each signal format.

The setting values are the same as that of “Area Marker”.

In 1:1 mode, this display is grayed out and cannot be operated.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Configuration (cont.)

Audio Setting

Settings for the audio output balance, EMBEDDED AUDIO signals and audio level meter signal.

Item

To do

Setting value

Balance

Adjust the balance between the right and left speakers.

L5 – L1, 0, R1 – R5

Audio1 Assign

Select the video input through which audio is output.

Analog audio is input through the AUDIO ASSIGN (IN 1) terminal.

SDI-1, SDI-2, HDMI-Digital,

HDMI-Analog, Component/

RGB, Video

Audio2 Assign

Select the video input through which audio is output.

Analog audio is input through the AUDIO ASSIGN (IN 2) terminal.

SDI-1, SDI-2, HDMI-Digital,

HDMI-Analog, Component/

RGB, Video

Embedded Audio Group*¹Select the audio channel group of the EMBEDDED AUDIO signals.

The setting values and selectable audio channels of EMBEDDED AUDIO signals are as

follows. (G means GROUP)

1G, 2G, 3G, 4G, 1-2G, 1-3G,

1-4G

1-2G

channel(s) 1/2/3/4/1+2/3+4/1 – 4 (1G)

channel(s) 5/6/7/8/5+6/7+8/5 – 8 (2G)

channel(s) 1/2/3/4/5/6/7/8/1+2/3+4/5+6/7+8/1 – 4 (1G)/5 – 8 (2G)/

1 – 8 (1G+2G)

1-3G

channel(s) 9/10/11/12/9+10/11+12/9 – 12 (3G)

channel(s) 1/2/3/4/5/6/7/8/9/10/11/12/1+2/

3+4/5+6/7+8/9+10/11+12/1–4(1G)/5–8(2G)/

9–12(3G)/1–8(1G+2G)/1–12(-3G)

1-4G

channel(s) 13/14/15/16/13+14/15+16/13–16(4G)

channel(s) 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16/1+2/3+4/

5+6/7+8/9+10/11+12/13+14/15+16/1–4(1G)/5–8(2G)/9–12(3G)/13-16(4G)/

1–8(1G+2G)/1–12(1-3G)/1-16(1-4G)

Level Meter Setting*¹

Specify the audio level meter display for EMBEDDED AUDIO signal.

Example of audio level meter display - Connection between the level meter position and channel

Ex: When “Horizontal” is selected for “Level Meter Display”:

REFERENCE

LEVEL

Ex: When “Vertical” is selected for “Level Meter Display”:

OVER LEVEL

-20dB -10dB

-10dB -20dB

-10dB

-20dB

Red

Yellow

Green

REFERENCE LEVEL

•

The number of audio channels displayed on the level meter varies depending on the setting value of “Embedded Audio

Group”.

•

The level meter with no audio signal input is displayed in white for “3COLORS”, and in gray for “White”.

Display position

When “Horizontal” is selected for “Level Meter Display”, the display position will be the top or bottom of the screen.

When “Vertical” is selected for “Level Meter Display”, the display position will be the lower right, lower left, upper left, or

upper right of the screen.

•

When “On” is selected for “Peak Hold”, the maximum value is retained a certain period when the signal level becomes

maximum.

Level Meter Display Select the status of the level meter (display vertically, horizontally, or not displayed).

Off, Vertical, Horizontal

Line, Divide

Horizontal Channel

Arrange

Select how the audio channels are displayed on the level meter.

Vertical Position

Horizontal Position

Meter Type

Adjust the vertical level meter position.

Adjust the horizontal level meter position.

Specify the design of the level meter.

Select the color of the level meter display.

1, 2, 3, 4

Upper, Lower

Bar, Block

Color

3Colors (colored depending

on the level),

White (white only)

Reference Level

Over Level

Select the standard input level indicated on the level meter.

–20dB, –18dB

Select the input level’s lower limit indicated in red for the “3Colors” display.

–10dB, –8dB, –6dB, –4dB,

–2dB

Bar Brightness

Transparent

Peak Hold

Select the brightness of the level meter.

Low, High

Adjust the transparency of the level meter display against the image.

Activates/deactivates the peak hold function of the level meter.

Off, Background, All

Off, On

Memorized for each input.

Download from Www.Somanuals.com. All Manuals Search And Download.

Sync Function

Settings for the synchronization with signals.

Item

To do

Setting value

No Sync Action

Select the screen status when no signal is coming in.

Off, Standby, Power Save

(power save mode),

Gray Back (gray screen)

Delay Time

Select the period until the screen status changes as selected in “No Sync Action” after signals 30s, 5min, 15min

stop coming in.

Low Latency

Activates/deactivates the function to shorten the time taken to display the picture (low

latency function).

Off, On

•

If the picture is not displayed steadily while “On” is selected, select “Off.”

While “On” is selected, the displayed picture may become unstable when an operation

using buttons on the front panel or the menu is performed, or when the signal format

changes.

● When setting “No Sync Action” to “Gray Back,” the screen color changes to gray and the power consumption of the backlight is saved by half.

Selecting “Power Save” (power save mode) saves more power consumption by turning off the backlight.

No Operation Action Setting values: Off, On

Setting of the function for turning the unit off (standby) automatically when no operations are made for more than 4 hours.

Off: Does not turn off automatically

On: Turns off automatically

● When the function is turned On, a warning message will be displayed about 3 minutes before turning off automatically.

When you turn on the unit with the function turned On, a message notifying that the setting is turned on will be displayed for about 30

seconds.

Set-Up Menu

Function Setting

Settings for the sub menu display, color of the tally lamp, and the intensity of the button lamps.

Item

To do

Setting value

sub menu Position

Select the contents and displaying position of “sub menu.”

The setting values and features are as follows.

Lower1, Upper1, Lower2,

Upper2

Lower1

Upper1

Lower2

Upper2

Displays the current setting and adjustment bar at the lower part of the screen.

Displays the current setting and adjustment bar at the upper part of the screen.

Displays the current setting at the lower part of the screen.

Displays the current setting at the upper part of the screen.

•

The adjustment bar is not displayed for some items.

Sync Term

Specify the terminal resistant value of the RGB input synchronized signal from the COMPO./RGB Low, High

terminal.

•

Normally, select “High”. Select “Low” when the display becomes unstable due to the length

of a connection cable.

Tally Setting

Tally Type

Set the color and mode of the tally lamp using external control.

Normal

Half

Light up the entire tally.

Light up the left and right halves of the tally individually.

Normal, Half

Tally Color

Dimmer

Illumination

Set the tally color when “Tally Type” is set to “Normal”.

Select the intensity of the button lamps.

Select whether illumination is activated/deactivated.

Green, Red

Normal, Dark

Off, On

Component Phase

Deactivates the function of PHASE adjustment (Picture adjustment knob and “Picture Sub

Adjust” in Set-Up Menu) except when an NTSC signal comes in (☞ on page 18).

Set the conditions for the power switch by external control (serial).

Enable, Disable

Remote Active On

Standby

Off, On

Off

Can power on by external control after powered OFF.

Cannot power on by external control after powered OFF.

LCD Saver

Configure the setting for reducing damage to the LCD panel for long-time use. (☞ on page 20)

Setting

1st Start Set the standby time.

00h-24h

01h-06h

Work

Time

Set the time for performing the function.

Contrast Set the contrast reduction.

Backlight Reduce the backlight brightness.

Save, Normal

OSD

Contrast

Set the contrast reduction of the OSD display.

Save, Normal

Off, On

Side Mask Select whether to use the side panel.

The Side Mask function works no matter whether the LCD Saver is active or stopped.

reset

Restore the default settings for all the items in “LCD Saver”.

Execute

Cancel

Status

Execute the LCD Saver function.

Stop the LCD Saver function. (“Cancel” will be grayed out during the function stop.)

Display the LCD Saver status.

Off, Ready

**h **min

Start After

Stop the LCD Saver function.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Configuration (cont.)

Picture Sub Adjust

Configure the standard level of image adjustment.

Item

Contrast*¹

To do

Setting value

–20 to +20

Adjust the standard level for the contrast adjusted with the CONTRAST knob on the front

panel.

Bright*¹

Adjust the standard level for the brightness adjusted with the BRIGHT knob on the front

panel.

Adjust the standard level for the chroma adjusted with the CHROMA knob on the front panel. –20 to +20

Adjust the standard level for the phase adjusted with the PHASE knob on the front panel.

Select the set-up level of the input NTSC signal.

–20 to +20

Chroma*¹

Phase*^1,*²

NTSC Setup

–20 to +20

00 (compliant with 0 %

set-up signal), 7.5 (compliant

with 7.5 % set-up signal)

Component Level

Select the level of the analog component signal (480i and 576i only).

B75 (compliant with

BetacamVTR 7.5 % set-up

signal), B00 (compliant with

BetacamVTR 0 % set-up

signal), SMPTE (compliant

with M2VTR signals)

sub menu

reset

Display the sub menu which enables you to adjust the items in “Picture Sub Adjust” while viewing the actual picture.

Restore the default settings for all the items in “Picture Sub Adjust”.

Memorized for each input.

When “Component Phase” is set to “Disable,” “Phase” cannot be adjusted if no NTSC signal is input.

White Balance Setting

Display the color temperature, and adjusts the drive level and cutoff point of each color (R/G/B).

Item

To do

Setting value

Color Temperature

R Drive *¹

G Drive

Select the color temperature. (Cannot be set/changed)

Adjust the drive level of each color (red, green, and blue).

● The maximum (Max) and minimum (Min) values vary depending on the input signal or

other settings.

9300K, 6500K, User

Min – 000 – Max

(in 1024 grades)

B Drive

R Cut Off *¹

G Cut Off

B Cut Off

sub menu

reset

Adjust the cutoff point of each color (red, green, and blue).

● The maximum (Max) and minimum (Min) values vary depending on the input signal or

other settings.

Display the sub menu which enables you to adjust the items in “White Balance Setting” while viewing the actual picture.

Restore the default settings for all the items in “White Balance Setting”.

Min – 000 – Max

(in 1024 grades)

Memorized for each color temperature.

Remote Setting

Settings for the external control.

Item

Serial Type

Parallel Type

Pin1

To do

Setting value

RS232C, RS485

Make, Trigger, Set

Select a terminal for external control in serial mode.

Select a control method of the MAKE/TRIGGER terminal.

Pin2

Pin3

Pin4

Assign the control functions to the pins of the MAKE/TRIGGER terminal.

☞ "Display" in "Functions

controlled by the Make/

Trigger system" on page 23

•

Assign a function to each pin terminal by selecting “Set” in “Parallel Type” mentioned

above.

Pin5

Pin6

Pin7

Pin8

The functions are assigned for “Pin6” – “Pin8” and you cannot change the assignment of

these functions.

Tally

Enable

GND

Download from Www.Somanuals.com. All Manuals Search And Download.

Information

Settings for the information display of the monitor.

Item

To do

Setting value

Source ID

Select whether the name assigned in “Character Setting” is displayed on the screen (☞ “On Off, On, Auto

the Information Display” on page 11).

•

When “Auto” is selected, the display color synchronizes with the color of the tally lamp

while the tally lamp is lit.

Character Setting

Status Display

Assign a name to each video source as you like (10 characters at maximum). You can also enter a name using the RS-232C

system. (☞ Page 20)

Display/Hide the status of the current input and the setting of MUTING. (☞ "On the Status

Display" on page 12)

Select the type of the TIME CODE display.

Auto, Off, On

Time Code

CRC Error

VITC*¹, LTC*¹, D-VITC

Display/Hide the CRC error when the HD SDI signal is input. (☞ "On the Information Display" Off, On

on page 11)

Sub Hour Meter

Model

Display the hours of use (unit: hour). The usage time can be reset to 0.

Display the model name of the monitor.

Version

Hour Meter*²

Display the version of the monitor.

Display the total hours of use (unit: hour). This item is used for maintenance of the monitor. You cannot reset this item.

Ancillary time code

”Hour Meter” and settings specified using the front knob are not reset.

Control Lock* Setting values: Off, Volume Lock, All Lock

Settings for disabling the buttons on the front panel.

• The following operations are not available when “Volume Lock” is selected.

- Picture adjustment knob

• The “All Lock” function disables to control the buttons on the front panel. But following operations are available.

- Turning on/off (on standby) the monitor

- Displaying the Set-Up Menu by pressing button while holding button and turning “Control Lock” to “Off”

- Operating the monitor by an external control

If you try other operations, “Control lock on!” appears on the screen.

Language

Setting values: English, Deutsch, Français, Español, Italiano, Pуccкий

Select the displayed language for the menu, etc.

IMD

Settings for IMD (In-monitor Display). (☞ Page 20)

Item

To do

Setting value

IMD Display

Display setting

On: Displayed, Off: Not displayed

On, Off

IMD Protocol

Address

Serial communication protocol setting

Off: Supports JVC protocol, TSL V4.0: Supports TSL UMD Protocol V4.0

Address setting

000 to 126: Set a particular address

Off, TSL V4.0

000 to 126

IMD Size

Text size setting

Small: Small size, Middle: Standard size, Large: Large size

Small, Middle, Large

Text Color

Text color setting

Command, Red, Green, Amber,

Blue, Cyan, Magenta, White

Command: Same color as that set for communication (Command)

Red, Green, Amber, Blue, Cyan, Magenta, White: Color settings

Tally 1 color setting

Command: Same color as that set for communication (Command)

Red, Green, Amber, Blue, Cyan, Magenta, White: Color settings

Tally 2 color setting

Command: Same color as that set for communication (Command)

Red, Green, Amber, Blue, Cyan, Magenta, White: Color settings

Display background color setting

Tally 1 Color

Command, Red, Green, Amber,

Blue, Cyan, Magenta, White

Tally 2 Color

Command, Red, Green, Amber,

Blue, Cyan, Magenta, White

Background Color

Black, Translucent, Transparent

Black: Set the background of the IMD display to black

Translucent: The picture on the monitor shows through the IMD display.

Transparent: Set the background of the IMD display transparent.

Return the “IMD” settings to their default values

reset

all reset

Restores all the settings and adjustments of the monitor to the default.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Configuration (cont.)

● Setting of “Character Setting”

Change the input to one that you want to assign a video source name for.

Select “Character Setting”.

Character Setting

Press

buttons to select the first character.

● Each time you press button, the character changes as follows.

Press button to reverse the order.

Space

Press button to move the arrow to the next space.

● The characters entered before moving the arrow are memorized.

Repeat steps 3 and 4 (10 characters at maximum).

Press MENU button to store the name.

● How to use the LCD Saver

1. Set reduced function to perform.

2. Set both time for starting the function and time for letting it work.

3. Activate the STANDBY MODE by Execute.

■ Aborting the ongoing function operation

Operating this apparatus may lead to aborting the OPERATION MODE.

■ Stopping the operation

Executing “Cancel”. Turn off the power.

● Once operating the function, unless turned off the power or executed “Cancel”, reduced function is automatically performed every 24 hours.

■ Example of setting up “1st Start” and “Work Time”

10h

12h

14h

16h

18h

20h

22h

24h

LCD Saver in

standby

LCD Saver in

operation

LCD Saver in

standby

Time to set in

the 1st Start

Time to set in

Work Time

Timing to run "Execute"

● IMD (In-monitor Display)

This unit supports “TSL UMD Protocol – V4.0” from Television Systems Ltd.

16 character text display and one tally on each side can be controlled.

The color of both the text and the tally can be set.

Using the address setting, up to 127 units can be controlled individually.

To use, set the external control terminals of this unit to serial format.

For details of control commands, refer to the homepage of Television Systems Ltd.

CAM-01

Tally 1

Text display area

Tally 2

* Example of lower screen IMD display

● Low Power Mode

Puts the unit into Low Power Mode 30 seconds after the monitor is switched off (standby) to further reduce power consumption.

•

Low Power Mode will not activate when “Remote Active On Standby” on the Set-up Menu is set to “On”.

The power lamp will be turned off during Low Power Mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Function Key Setting

Specify the function assigned to the F1/F2 button.

● To display “Function Key Setting” Menu

Press the button when the menu is not displayed.

Press the MENU button to exit from "Function Key Setting” Menu.

Item

To do

Setting value

Function1

Specify the function assigned to the F1 button.

- - -, Aperture, I/P Mode,

Frame, Center Marker,

Level Meter Display,

Gamma, Color Temperature,

CRC Error

Function2

Specify the function assigned to the F2 button.

Function Display

Select whether to display the status of the assigned function when you press the F1/F2 button.

Off, Mode-1, Mode-2

Off

Mode-1

Mode-2

No status display. Perform the registration function.

Display the status. Perform the registration function.

Display the status. Do not perform the registration function.

Perform the registration function when the status is displayed and the button is

pressed again.

See pages 13 to 20 for details of the functions assigned to Function 1 and Function 2.

● About the operations of F1/F2 button

Each time you press the button, the setting value for the assigned function changes in order.

Ex: When “Color Temperature” is assigned

Each time you press the button, three setting values alternate.

Download from Www.Somanuals.com. All Manuals Search And Download.

External Control

About the external control

This monitor has three external control terminals.

● Make/Trigger terminal (RJ-45): The following external control

systems are available.

Control priority is as follows.

Make > Trigger = serial communication = buttons and menu on

the monitor

(1) Make (make contact) system:

● You can use external control even when “Control Lock” is set to

“Volume Lock” or “All Lock” (☞ page 19).

Controls the monitor by short-circuiting the corresponding pin

terminal to the GND pin terminal, or disconnecting (opening) it.

(2) Trigger (trigger) system:

● When the monitor is off (on standby), external control is not

available. But certain external controls (starting/terminating

communication, turning on the monitor) are available through the

serial communication (☞ page 24).

Controls the monitor by sending the pulse signal instantaneously

to the corresponding pin terminal.

☞ “Using the Make/Trigger system” below

● RS-485 terminals (RJ-45): Controls the monitor with the RS-485

system (☞ “Using the serial communication” on page 23).

● RS-232C terminal (D-sub 9-pin): Controls the monitor with the

RS-232C system (☞ “Using the serial communication” on page 23).

Set the following items of “Remote Setting” in Set-Up Menu

according to the external control terminal and control system (☞

“Serial Type,” “Parallel Type” on page 18).

You can control the monitor by a personal computer or dedicated

controller*².

● “Using the Make/Trigger system” below.

The controller is not commercially available. Consult your dealer if

you need it.

The settings of this unit

Control

Control system

“Serial Type”

setting

“Parallel

Type” setting

terminal

Make/

Trigger

terminal

Parallel Type

Make

—

Make

PC, etc.

Trigger

RS-485

terminal

RS-232C

terminal

Serial

communication

RS-485

—

RS-485 IN

RS-232C

RS-485

OUT

RS-485

OUT

RS-485

OUT

RS485*¹

RS-232C

RS232C*¹

● For the details, see page 23.

For a monitor connected to a personal computer etc, select the

terminal the equipment is actually connected to. For other monitors,

select “RS485.”

Using the Make/Trigger system

The Make/Trigger terminal is configured as follows. You can assign a

function to each pin terminal in “Remote Setting” (☞ “Pin1, Pin2, Pin3,

Pin4, Pin5” in “Parallel Type” on page 18).

To assign the functions to the pin terminals

For the operation procedure, see page 12.

Select “Remote Setting” on the Set-Up Menu.

Set “Parallel Type” to “Set.”

Select a pin name (“Pin1” – “Pin5”) for which you want to assign a

function, then select the function you want to assign.

For the selectable functions, see the table on page 23.

● You cannot change the functions assigned to the pin terminals

from 6th to 8th.

Pin No.

Pin name

Pin1

Operation of the external control

Set “Parallel Type” of “Remote Setting” to “Make” or “Trigger” in the

Set-Up Menu.

Pin2

Pin3

Pin4

Short-circuit the 7th pin terminal (ENABLE) to the 8th pin terminal

(GND) so that the monitor can be controlled by the external control.

When the “Make” system is selected: Operate each function by short-

circuiting the corresponding pin terminal to the 8th pin terminal

(GND) or opening it.

When the “Trigger” system is selected: Operate each function by

pulse control, that is short-circuiting the corresponding pin terminal

to the 8th pin terminal (GND) for about 1 second and opening it.

Pin5

This is a female terminal.

Tally*¹

Enable*²

GND

The 6th pin terminal controls turning on or off the tally lamp

(available to control even when the 7th pin terminal is invalid).

The 7th pin terminal makes the external control valid/invalid. Make

sure to control the terminal by the Make system.

● When changing the input with Make system, activate the pin you

want after deactivating the currently used pin.

● When selecting the “Trigger” system, you can operate only one

function at a time. Operate the functions one by one.

Download from Www.Somanuals.com. All Manuals Search And Download.

Display Functions to be controlled

Opening

Short-circuiting

– – –

No function.

—

Green

Whole

—

Red

Tally lamp color selection.*¹

Tally lamp lighting method selection.

Light the left half of the tally lamp in red.*²

Light the right half of the tally lamp in green.*²

Changes the input to “SDI 1.”

Changes the input to “SDI 2.”

Changes the input to “HDMI.”

Changes the input to “COMPO./RGB.”

Changes the input to “VIDEO.”

The area marker indication.

The safety marker indication.

The center marker indication.

Indication of the area of the specified aspect ratio.

Selects the items of “Marker”.*³

Changes the aspect ratio.

Tally Color

Tally Type

Tally-L(R)

Tally-R(G)

SDI 1

One half at a time

Off

Invalid

Off

Valid

SDI 2

HDMI

Component/RGB

Video

Area Marker

Safety Marker

Center Marker

Frame

Marker Select

Manual Aspect

1:1

Non-“R-” items

4:3

“R-” items

16:9

Displays in 1:1 mode.

Status display.*⁴

Audio level meter display.

Time code display.

☞ “Source ID” in “Information” on page 19.

Color off.

Screens check.

Change a mode according to a input picture.

Muting on/off.

Off

☞ “On the Status Display” on page 12

Status

Level Meter

Time Code

Source ID

Color Off

Screens Check

I/P Mode

Off

Color

Monochrome

Off

Muting

Change the intensity of the button lamps.

Normal

Dark

Dimmer

Can be controlled when “Tally Type” (“Set-Up Menu” → “Function Setting” → “Tally Setting”) is set to “Normal”.

Can be controlled when “Tally Type” (“Set-Up Menu” → “Function Setting” → “Tally Setting”) is set to “Half”.

Selects which functions in “Marker” are activated, non-“R-” items or “R-” items (☞ “Marker” on page 15).

Displays the information shown when INPUT SELECT button of the current input is pressed (☞ “On the Status Display” on page 12). While controlling

with the Make system, the information is displayed only at the moment of short-circuiting.

While controlling with the Make system, the level meter is switched between displayed (short-circuiting) and hidden (opening). When “Level Meter

Display” is set to “Off,” the level meter is not displayed (“No Effect” appears).

While controlling with the Trigger system, the pattern of the audio channel display is switched.

While controlling with the Make system, the available set-up options will be the setting value currently selected in “Source ID” (“On” or “Auto” [short-

circuiting]) and “Off” (opening). While controlling with the Trigger system, uses the same set-up option as those in the Set-Up Menu (☞ “Source ID” in

“Information” on page 19).

While controlling with the Make system, the screen is switched between normal screen (opening) and blue screen (short-circuiting). While controlling

with the Trigger system, the screen changes in the same way as when pressing SCREENS CHECK button (☞ w on page 10).

Must be controlled with the Trigger system. The mode changes in the order of “Normal” → “Cinema” → “Field.” (This function cannot be controlled

with the Make system.)

● You cannot assign the same function to different pin terminals.

● The Trigger system switches each function by short-circuiting the pin terminal for about 1 second and opening it.

Using the serial communication

You can control the monitor from a personal computer etc. via the RS-485 or RS-232C terminal.

* Consult your dealer for the details of the external control specification.

Input terminal

RS-485

RS-232C

Cable

Terminal specification

Communication specifications

A straight LAN cable

Baud Rate: 4800 bps

Data Bits: 8 bits

Parity: No parity

A straight cable with a D-sub 9-pin connector

(male for the monitor, female for the personal

computer etc.)

☞ See below

Stop Bits: 1 bit

Flow Control: No control

Communication Code: ASCII Code

OUT terminal

signal

TXD +

TXD –

RXD +

RXD –

Pin No.

Signal

Pin No. IN terminal signal

TXD +

TXD –

RXD +

RXD –

RXD

TXD

GND

RTS

CTS

This is a female

terminal.

This is a female

terminal.

GND

● The 7th terminal and the 8th terminal are connected.

Download from Www.Somanuals.com. All Manuals Search And Download.

External Control (cont.)

All commands consist of the following segments.

Header

Monitor ID

Function

Data

Cr (0Dh)

On Header

“!” : Operation commands from the personal computer, etc. (☞ <Basic command list> below table).

“?” : Reference commands from the personal computer, etc.

“@” : Status returns from the monitor

To start communication, send the connection command from the personal computer etc.

To terminate the communication, send the termination command from the personal computer etc.

Example of communication procedures

1 Starting the communication:

connection command (!00BCN1Cr)

Monitor

2 Monitor’s status (@00BOKCr)

3 Selecting “SDI 1” input (!00BINACr)

4 Monitor’s status (@00BOKCr)

PC, etc.

5 Terminating the communication:

termination command (!00BCN0Cr)

6 Monitor’s status (@00BOKCr)

No.

Commands

Functions

Data

Starts communication (connection)

No data

Terminates communication (termination)

x*²Cr Assigns the control ID

No data

01 – 99

Initializes the control ID

x*²Cr Displays/hides the ID

No data

00: Hide, 01: Display

No data

Displays the Main Menu/Quits the menu operation

Moves the cursor upward (

Moves the cursor downward (

No data

)

No data

)

Makes setting/adjustment (

Displays the Set-Up Menu

Turns on the monitor

)

No data

)

No data

Turns off the monitor (on standby)

Selects “SDI 1” input

No data

Selects “SDI 2” input

No data

Selects “HDMI” input

No data

Selects “COMPO./RGB” input

No data

Selects “VIDEO” input

Displays the status*³

x*²Cr Turns muting on/off

No data

x*²Cr

No data

00: Off, 01: On

00: 4:3, 01: 16:9

No data

Changes the aspect ratio

Increases the volume

Reduces the volume

Sets the volume

x*²Cr

No data

00-30

● “Cr” is 0Dh.

● The commands for starting communication (connection) (No. 1), terminating communication (termination) (No. 2), and turning on the

monitor (No. 13) can be used while the monitor is off (on standby).

Enter the monitor’s ID for “ **.” The initial setting of the monitor’s ID is “00.” When connecting several monitors, “00” is a command for controlling all

monitors at once.

Enter the appropriate data to “xx.”

Displays the information shown when the INPUT SELECT button currently lit is pressed (☞ “On the Status Display” on page 12).

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Solutions to common problems related to the monitor are described here. If none of the solutions presented here solve the problem, unplug the

monitor and consult an authorized dealer or service center.

Symptom

Probable cause and corrective action

Page

● Press the

● Firmly insert the AC power plug.

● Turn on the POWER switch on the rear panel.

button.

No power supply.

● Select the correct input using the INPUT SELECT buttons.

● Connect the signal cable firmly.

● Turn on the power of the connected component and set the output correctly.

● Check whether the input signal format is acceptable on the monitor.

—

No picture with the power on.

29, 30

● Adjust the volume level.

● Deactivate the muting function.

● Connect the signal cable firmly.

No sound.

● Turn on the power of the connected component and set the output correctly.

—

“Out of Range” appears.

● Check whether the input signal format is acceptable on the monitor.

12, 29, 30

● Select the correct input using the INPUT SELECT buttons.

● Connect the signal cable firmly.

● Turn on the power of the connected component and output video signals. Or,

check whether the video output of the component (video output setting of the VCR

or graphic board of the computer) is set correctly.

—

“No Sync” appears.

● Adjust each picture adjustment knob on the front panel or adjust the items of

“Picture Sub Adjust” in the Set-Up Menu. Or, perform “reset” in “Picture Sub Adjust.”

● Check whether the setting of COLOR Off or SCREENS CHECK buttons are

appropriate.

● Select the proper color system (“Color System”) in “Signal Setting”.

● Adjust the items of “White Balance Setting” in the Set-Up Menu. Or, perform “reset”

in “White Balance Setting”.

10, 18

Wrong color, no color.

● Adjust the picture contrast or brightness by using the adjustment knobs on the

front panel. Or, adjust “Contrast” or “Bright” of “Picture Sub Adjust” in the Set-Up

Menu.

10, 18

The picture becomes blurred.

Wrong picture position, wrong picture size.

● Check whether the setting of 1:1 is appropriate.

29, 30

● Check “Manual Aspect” and “SD4:3 Size” settings in Aspect menu.

● Check whether the input signal format is acceptable on the monitor.

● Adjust the picture size (H Size/V Size) or position (H Position/V Position) of “Size/

Position Adjust” menu.

The picture may sometimes not be able to fill

the whole screen depending on the signal. In

this case, nothing can be done to solve the

problem. Please be aware of this beforehand.

● Set “Control Lock” in the Set-Up Menu to “Off.”

● You cannot use the buttons for the items controlled by the Make system. Disable

the external control.

18, 22

Buttons on the monitor do not work.

The following are not malfunctions.

● When a still image is displayed for a long time, it may remain indistinctly on the screen after the picture has changed. Though the remaining

picture will disappear after a while, there may be a case that it remains for a long period depending on the length of time the still image was

displayed for. This is due to the characteristics of the LCD display and is not a malfunction.

● Red spots, blue spots and green spots on the panel surface are a normal characteristic of LCD displays, and not a problem. The LCD display is built

with very high precision technology; however, be aware that a few pixels may be missing or constantly lit.

● The following symptoms are problems only when pictures or sounds are not played back normally.

● A slight electric shock occurs when you touch the monitor.

● The top and/or rear panel of the monitor becomes hot.

● The monitor emits a cracking noise.

● The monitor emits a mechanical noise.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting (cont.)

Self-check program

This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes troubleshooting easier. Whenever a

problem occurs, one or some of the INPUT SELECT lamps will flash. If this happens, follow the steps below and contact your dealer to resolve the

problem.

The illustration of the monitor is of DT-E21L4.

When the screen goes blank, and one or some of the INPUT SELECT lamps (COMPO./RGB, VIDEO) on the front control panel start

flashing...

Check which lamps are flashing.

Press

button to turn off (on standby) the monitor.

Turn off the power switch on the rear panel.

Disconnect the AC power cord from the AC outlet.

Contact your dealer with the information about which lamps were flashing.

● If you turn on the monitor soon after turning it off (or after a short-term power failure), the INPUT SELECT lamps may flash and no image may

be displayed.

When this happens, turn off power and wait at least 10 seconds before turning on the monitor again.

If the INPUT SELECT lamps do not flash, you can use the monitor as normal.

● The self-check function does not work when the setup menu “Remote Active On Standby” is set to “Off” and you turn off the monitor (put the

monitor in standby).

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

General

Model name

Type

DT-E21L4

DT-E17L4G

Multi format LCD monitor

Type 21 wide format

16:9

Screen size

Aspect ratio

Type 17 wide format

Horizontal/vertical frequency

(computer signal)

31.469 kHz – 75.000 kHz

49.990 Hz – 75.062 Hz

* Some signals within this frequency range may not be displayed (“Out of range” is displayed).

☞ “Available signals” on page 29

Compliant video signal format

Format

HD SDI:

SD SDI:

BTA S-004C, SMPTE292M

ITU-R BT.656:

SMPTE259M:

525/625

525

EMBEDDED AUDIO: SMPTE299M, SMPTE272M

Audio output

Internal speaker: 1.0 W + 1.0 W

Operating conditions

Operating temperature: 5°C – 35°C (41°F – 95°F)

Operating humidity: 20% – 80% (non-condensing)

(Slightly variable depending on ambient conditions for installation.)

Power requirements

Rated current

AC 120 V, 50 Hz/60 Hz or DC 12 V – 17 V

0.6 A (AC 120 V)

3.5 A (DC 12 V - 17 V)

0.5 A (AC 120 V)

3.0 A (DC 12 V - 17 V)

External dimensions

Width: 515 mm (20 3/8˝)

515 mm (20 3/8˝)

Width: 430 mm (17˝)

430 mm (17˝)

(excluding protruding parts)

Height: 352.1 mm (13 7/8˝)

Depth: 181 mm (7 1/4˝)

(with the stand)

347 mm (13 3/4˝)

99.8 mm (4˝)

(without the stand)

Height: 314.1 mm (12 3/8˝)

Depth: 181 mm (7 1/4˝)

(with the stand)

309 mm (12 1/4˝)

102 mm (4˝)

(without the stand)

Weight

7.7 kg (16.9 lbs) (with the stand)

6.2 kg (13.6 lbs) (without the stand)

7.1 kg (15.6 lbs) (with the stand)

5.6 kg (12.3 lbs) (without the stand)

Accessories

AC power cord x 1, Power cord holder x 1, Screw x 2 (for power cord holder)

LCD panel

Type

21˝ wide, active matrix TFT

Width: 477 mm (20 1/2˝)

17˝ wide, active matrix TFT

Width: 382 mm (14 3/4˝)

Effective screen size

Height: 268 mm (12 7/8˝)

Diagonal: 547 mm (21 9/16˝)

Height: 215 mm (8 3/8˝)

Diagonal: 438 mm (17 1/4˝)

Number of pixels displayed

Number of colors displayed

Viewing angle (TYP.)

Brightness (TYP.)

1920 x 1080

16.70 million

170° (Horizontally), 160° (Vertically)

250 cd/m²

160° (Horizontally), 60° (Upward), 80° (Downward)

300 cd/m²

Contrast ratio (TYP.)

1000:1

600:1

Input/output terminals

VIDEO

Input/output of composite signal:

1 line, BNC connector x 2, 1 V (p-p), 75 Ω

* The input (IN) and output (OUT) terminals are bridge-connected

(auto termination).

HDMI

HDMI signal input (compatible with HDCP)

HDMI connector x 1

COMPO./RGB

(R, G, B, HS, VS or Y, Pb/B-Y,

Pr/R-Y)

Analog Component signal input/Analog RGB signal input:

1 Line, mini D-SUB 15pin x1

Y: 1 V(p-p), 75 Ω(with sync)

G, B/PB/B-Y, R/PR/R-Y: 0.7 V (p-p), 75 Ω

HS, VS: 0.3 V (p-p) to 5 V (p-p)

* For HS and VS, change the Low/High terminals manually.

E. AUDIO HD/SD SDI (IN 1)

E. AUDIO HD/SD SDI (IN 2)

Digital signal input (compatible with EMBEDDED AUDIO signals):

auto detection, 2 line, BNC connector x 2

E. AUDIO HD/SD SDI

(SWITCHED OUT)

Digital signal output (compatible with EMBEDDED AUDIO signals):

1 line switched out, BNC connector x 1

AUDIO (IN)

Analog audio signal input:

2 line, RCA connector x 2, Stereo mini Jack x1, 500 mV (rms), high impedance

AUDIO (MONITOR OUT)

REMOTE (MAKE/TRIGGER)

Analog audio signal output:

1 line, RCA connector x 2, 500 mV (rms)

☞ “Using the Make/Trigger system” on page 22

☞ “Using the serial communication” on page 23

REMOTE (RS-485)

REMOTE (RS-232C)

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications (cont.)

Dimensions

Unit: mm (inch)

DT-E21L4

99.8 (4)

VESA mounting holes

(Size: M4, depth: 10 mm)

53 (2 1/8)

1.3 (1/16)

100

515 (20 3/8)

3 (1/8)

20.2 (7/8)

300 (11 7/8)

181 (7 1/4)

To install the monitor on a shelf

To install the monitor on a wall

270 (10 3/4)

210 (8 3/8)

160 (6 3/8)

36.7 (1 1/2)

15.1 (5/8)

70 160 (6 3/8) 70

88.2

(3 1/2)

179 (7 1/8)

(2 7/8)

DT-E17L4G

102 (4 1/8)

VESA mounting holes

(Size: M4, depth: 10 mm)

(2 1/4)

100

430 (17)

1.3 (1/16)

3 (1/8)

18 (3/4)

300 (11 7/8)

181 (7 1/4)

To install the monitor on a shelf

To install the monitor on a wall

270 (10 3/4)

210 (8 3/8)

160 (6 3/8)

36.7 (1 1/2)

17.3

(3/4)

(2 7/8)

88.2

(3 1/2)

179 (7 1/8)

160 (6 3/8)

Download from Www.Somanuals.com. All Manuals Search And Download.

Available signals

The following signals are available for this monitor.

Video signals

Input terminal

analog RGB

Signal format shown in

E.AUDIO *¹

HD/SD SDI

No.

Signal name

the status display

VIDEO

analog COMPO.

HDMI

(☞ page 12)*⁵

NTSC

√

—

√

—

√

—

√

—

√

NTSC 4.43

PAL-M

PAL60

PAL

N 4.43

√

PAL-M

√

PAL60

√

PAL

√

PAL-N

SECAM

B/W50

B/W60

PAL-N

√

SECAM

√

B/W50

√

B/W60

√

10 480/60i

480/60i

—

11 480/59.94i

12 576/50i

480/59.94i

576/50i

√

13 480/60p

480/60p

√

—

√

14 480/59.94p

15 576/50p

480/60p

√

576/50p

√

16 640*480/60p

17 640*480/59.94p

18 720/60p

640*480/60p

720/60p

—

√

—

√

19 720/59.94p

20 720/50p

720/59.94p

720/50p

√

21 720/30p

720/30p

—

√

—

√

22 720/29.97p

23 720/25p

720/29.97p

720/25p

√

24 720/24p

720/24p

√

25 720/23.98p

26 1080/60i

720/23.98p

1080/60i

1080/59.94i

1035/60i

1035/59.94i

1080/50i

1080/60p

1080/50p

1080/30p

1080/29.97p

1080/25p

1080/24p

1080/23.98p

1080/30psf

1080/29.97psf

1080/25psf

1080/24psf

1080/23.98psf

√

27 1080/59.94i

28 1035/60i

√

—

√

29 1035/59.94i

30 1080/50i

√

31 1080/60p

32 1080/59.94p

33 1080/50p

34 1080/30p

35 1080/29.97p

36 1080/25p

37 1080/24p

38 1080/23.98p

39 1080/30PsF

40 1080/29.97PsF

41 1080/25PsF

42 1080/24PsF

43 1080/23.98PsF

√

—

√

—

√

√*²

√*³

√*⁴

√

—

√

√: Acceptable

—: Not acceptable

Compatible with EMBEDDED AUDIO signals.

The signal is recognized as 1080/60i, and the status is displayed as “1080/60i.”

The signal is recognized as 1080/59.94i, and the status is displayed as “1080/59.94i.”

The signal is recognized as 1080/50i, and the status is displayed as “1080/50i.”

For signal formats other than E.Audio HD/SD SDI input, **/59.94, **/29.97, and **/23.98 will be displayed as **/60, **/30, and **/24 respectively.

● HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United

States and other countries.

● HDCP stands for High-bandwidth Digital Content Protection, a copy protection technology of high reliability licensed by Digital Content

Protection, LLC.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications (cont.)

Computer signals (preset)

Analog RGB input (COMP./RGB terminals) and DVI input (HDMI terminal):

Resolution

Horizontal

640

Frequency

Horizontal (kHz)

No.

Signal name

Scan system

Vertical

480

600

768

Vertical (Hz)

59.9

60.3

60.0

50.0

70.1

60.0

66.7

74.5

74.9

75.1

VGA60

WVGA60

SVGA60

31.5

37.9

48.4

47.8

55.9

64.0

75.0

74.0

67.5

56.3

31.5

47.7

64.0

65.2

35.0

49.7

60.2

68.7

Non-interlace

852

800

XGA60

1024

1280

1440

1280

1600

1920

720

1360

1400

640

WXGA (1280)

WXGA+60

SXGA60

768

900

1024

1200

1080

400

UXGA60 *¹

WUXGA60 *¹

1080/60p

1080/50p

US TEXT *^2,*⁵

WXGA(1360)

SXGA+/60A *³

SXGA+/60B *⁴

MAC13 *⁵

768

1050

480

624

768

MAC16 *⁵

MAC19 *⁵

MAC21 *⁵

832

1024

1152

870

No. 8 and No. 9 signals come in, thin lines will become obscured because their signal resolution is higher than the screen resolution.

The signal is recognized as VGA400/70, and the status is displayed as “VGA400/70”.

The signal is recognized as SXGA+60, and the status is displayed as “SXGA+60”.

The signal is recognized as SXGA+60*, and the status is displayed as “SXGA+60*”.

Only supports analog RGB input.

● Non-preset signals may not be displayed normally even if the frequency is within the acceptable range.

● When a preset signal comes in, the signal format is shown on the status display. When a non-preset signal comes in, “Out Of Range” appears.

Specification of the HDMI terminal

Connect it to the HDMI output terminal of a video device.

Pin No.

Input signal

T.M.D.S Data 2+

Pin No.

Input signal

T.M.D.S Data 0 shield

T.M.D.S Data 0–

T.M.D.S Clock+

Pin No.

Input signal

SCL

T.M.D.S Data 2 shield

T.M.D.S Data 2–

SDA

DDC/CEC GND

+5 V Power

T.M.D.S Data 1+

T.M.D.S Clock shield

T.M.D.S Clock–

T.M.D.S Data 1 shield

T.M.D.S Data 1–

Hot Plug Detect

CEC

T.M.D.S Data 0+

Spare (not connected)

Specification of the mini D-SUB15pin terminal

Connect it to the mini D-SUB15pin output terminal of a video device.

Pin No.

Input signal

Red video signal

Green video signal or Sync on

Green signal

Blue video signal

Not connected

Ground

Pin No.

Input signal

Red video signal return

Green video signal return

Blue video signal return

Not connected

Pin No.

Input signal

I2C data

Horizontal or Composite

synchronization signal

Vertical synchronization signal

I2C clock

Ground

Not connected

Notice on transportation

This monitor is precision equipment and needs dedicated packing material for transportation.

Never use any packing material supplied from sources other than JVC or JVC-authorized dealers.

● For easy understanding, pictures and illustrations are shown by being emphasized, omitted or composed, and may be slightly different

from actual products.

● Design and specifications are subject to change without notice.

● All company names and product names mentioned herein are used for identification purposes only, and may be the trademarks or

registered trademarks of their respective companies.

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

Download from Www.Somanuals.com. All Manuals Search And Download.

0212TMH-MW-MT

Download from Www.Somanuals.com. All Manuals Search And Download.

Indesit Washer Dryer WIDL 126 User Manual
Jenn Air Ventilation Hood MK7030 User Manual
Jensen Stereo System JBR550 User Manual
JVC Camcorder GR AXM17 User Manual
JVC Portable CD Player RD T50RLB User Manual
Kawasaki Power Hammer Rotary Tool User Manual
Kenwood Home Security System NX 410 User Manual
Kettler Home Gym 07653 000 User Manual
Kidco Camping Equipment P202 User Manual
Kodak Printer DS9050 User Manual