INSTRUCTIONS
MC-R434U
For Customer Use:
Enter below the Model No. and Serial
No. which are located at the top of the
unit. Retain this information for future
reference.
Model No. MC-R434U
Serial No.
Thank you for purchasing the JVC MC-R434U DVD-RAM/R DRIVE.
Before you start operating this unit, please read the instructions
carefully in order to obtain the best possible performance.
This instruction book is made from 100% recycled paper.
LST0172-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION FLOW
Follow the steps below for installation.
INSTALLATION
Install the MC-R434U in the CD/DVD Library.
Ⅵ Procedure for Opening the Door of the CD/DVD Library
Ⅵ Procedure for Opening the Drive Storage Cover of the
CD/DVD Library
●
Page 3, 4
Ⅵ Procedure for Determining the Setup Position for the MC-R434U
Ⅵ Procedure for Installing the MC-R434U in the CD/DVD Library
CONNECTION
Connect the MC-R434U to the CD/DVD Library.
Ⅵ Procedure for Connecting the Cables to the Back of the MC-R434U
●
●
Page 4, 5
Page 5
SETUP
Set the SCSI ID of the MC-R434U and close the door of the CD/
DVD Library.
Ⅵ Procedure for Setting the DIP Switch
Ⅵ Procedure for Attaching the Drive Storage Cover of the CD/DVD
Library
Ⅵ Procedure for Closing the CD/DVD Library Door
EXECUTION OF AUTOMATIC
DRIVE DETECTION MODE.
Execute the automatic drive detection mode and connect the host
computer.
●
Page 6
Ⅵ Procedure for Executing the Automatic Drive Detection Mode of
the CD/DVD Library
Ⅵ Procedure for Connecting the CD/DVD Library to the Host Com-
puter
PRECAUTIONS BEFORE USE
The MC-R434U is a DVD-RAM/R drive designed for use with
The ambient temperature around the CD/DVD Library should
be maintain at about 5˚C to 30˚C when a MC-R434U is con-
nected to multiple units of the MC-8100LU or MC8200LU/
8600LU the CD/DVD Library, as mentioned below.
●
●
the JVC MC-8100LU/8200LU/8600LU “CD/DVD Library”.
When installing this unit in a Library that is being used, please
read the instruction manual carefully.
●
The MC-R434U cannot be operated on its own.
This unit cannot be used in combination with the following
models.
• MC-8100LU
• MC-8200LU/8600LU : 6 units
: 4 units
●
●
1. DANGER: Invisible laser radiation will occur if the unit is
open due to a failed or defective interlocking device.
2. CAUTION: Do not open the top cover.There are no user
serviceable parts inside the unit; leave all servicing to
qualified service personnel.
• CD-ROM Library : MC-1000 series/2000 series
• DVD-RAM Library: MC-7000 series
• CD/DVD Library : MC-8000 series
For the compatible discs, see the Specifications on page E7.
●
E
Download from Www.Somanuals.com. All Manuals Search And Download.
Procedure for Opening the Drive Storage
Cover of the CD/DVD Library
INSTALLATION
Install the MC-R433U in the CD/DVD Library.
Before starting installation, be sure to turn both the
host computer and peripherals off.
For information related to the CD/DVD Library, refer
to the instruction manual for the CD/DVD Library.
●
Drive storage
section
Screw
Screw
Procedure for Opening the Door of the
CD/DVD Library
Drive storage
cover
<With the MC-8100LU>
Drive locking
screw mounting
hole
Drive storage
section
Drive storage cover
Screw
Drive storage
section
<With the MC-8100LU>
* The illustration shows the CD/DVD Library with the drive storage
cover removed for ease of description.
<With the MC-8200LU>
1.
2.
Remove the screws from the drive storage cover of the
CD/DVD Library.
Drive storage
section
Remove the drive storage cover.
Procedure for Determining the Setup
Position for MC-R434U
Drive locking
screw mounting
hole
Drive No. 6
Drive No. 5
Drive No. 4
Drive No. 3
Drive No. 2
Drive No. 1
Drive No. 4
Drive No. 3
Drive No. 2
Drive No. 1
<With the MC-8200LU>
1.
Select the [DOOR OPEN MODE] on the MENU screen of
the CD/DVD Library's LCD.
<
MC-8100LU drive storage section>
2.
3.
Press and hold the "SELECT" switch for five seconds.
<
MC-8200LU drive storage section>
Turn off the power of the CD/DVD Library when [THE DOOR
CAN BE OPENED] message is displayed on the LCD.
1.
Install the drives to the drive slots No.1 through No.6 (No. 1
through No. 4 in the case of the MC-8100LU) sequentially.
Ⅵ It makes the work easy if the drives are installed from
the lowest number to the highest.
4.
Insert the key in the key cylinder located at the center of
the door to unlock and open the door.
E
Download from Www.Somanuals.com. All Manuals Search And Download.
Procedure for Installing the MC-R434U in
the CD/DVD Library
CONNECTION
Connect the MC-R434U to the CD/DVD Library.
Also refer to the instruction manual for the CD/
DVD Library.
●
Sensor slit
Procedure for Connecting the Cables to
the Back of the MC-R434U
MC-R434U
Interior
Terminator
Drive 6
Internal SCSI (LVD) cable
<MC-R434U insertion direction>
MC-R434U
Drive 5
68-pin external SCSI connector
Drive 4
To host computer (SE/LVD)
Drive 3
SE-LVD conversion board
Drive 2
Drive 1
Terminator
Library SCSI board
Internal SCSI (SE) cable
<MC-R434U connection example>
Drive locking
screw
Control cable
<MC-R434U locking method>
1
14p
DIP switch
1.
Insert the MC-R434U from the rear of the CD/DVD Library
Ⅵ Be sure not to damage the sensor slit.
Ⅵ Make sure that the direction of the MC-R434U is correct
when inserting it.
Ⅵ Be sure that the cables connected to the rear of the CD/
DVD Library are not caught or pinched when inserting
the MC-R434U.
4p
2
Power cable
3
SCSI cable
<MC-R434U rear panel>
1.
Connect the power supply cable, control cable and SCSI
cable to the connectors at the rear of the MC-R434U.
Ⅵ When using the MC-8100LU, the No. of the cable must
always correspond to the No. of the drive bay to which it
is being connected. If a cable with the wrong number is
connedted, it will lead to the equipment malfunctioning.
Ⅵ When using an MC8200LU/8600LU, connect the con-
trol cables which lead from the side of the drive bay where
the MC-R434 is to be inserted.
2.
3.
Insert the MC-R434U slowly until the screw installation hole
located on the side of the MC-R434U and the screw instal-
lation hole located on the drive locking section are aligned.
Screw in the provided drive locking screw to the screw in-
stallation hole of the drive locking section.
Ⅵ Tighten the screw firmly.
Ⅵ If the drive locking screw is loose, the drive and/or Li-
brary may be damaged.
Ⅵ Insert all connectors firmly.
Ⅵ SCSI cables are connected as a daisy chain connec-
tion. Each connector should be connected to the drive
positions as illustrated in the diagram.
• The SCSI cable, which is built into the MC-8100LU/
8200LU/8600LU standard models, terminates at the
location where the connection is physically terminated.
E
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the cables
SETUP
Set the SCSI ID of the MC-R434U and close the door
of the CD/DVD Library.
●
Always turn the power of the CD/DVD Library off when
the dip switches are moved.
For the details of the default factory settings, please
refer to the section "SCSI ID No. SETTING" of the
instructions from the CD/DVD Library.
Library
Procedure for Setting the DIP Switch
<SE-LVD conversion board>
ON
Internal SCSI (SE) cable
ON
4.
50p
6p
OFF
1
2
3
4
LVD
power cable
3.
6p
(Factory setting)
68p
Internal SCSI (LVD) cable
5.
To each drive
<MC-R434U DIP switch settings on the rear panel>
2.
Connect the two LVD power cables (6P) to the SE-LVD
conversion board.
Ⅵ Both cables have identical connector types, so that ei-
ther cable can be connected to either connector on the
SE-LVD conversion board.
1.
ID2, ID1, ID0: Setting of the SCSI ID No. of each drive.
Ⅵ When setting the SCSI ID No., use a number that is not
being used by other SCSI devices on the same bus.
Ⅵ The MC-R434 should be used with one of the SCSI ID
No. 0 to 7. It cannot be used with No. 8 to 15.
Ⅵ RSV: Not available
3.
4.
Connect the internal SCSI (SE) cable (50P) to the SE-LVD
conversion board.
Ⅵ The other end of the internal SCSI (SE) cable is con-
nected to the library SCSI board in the library.
<SCSI ID No. and DIP switch settings>
Switch
SCSI ID No.
ID2
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ID1
OFF
OFF
ON
ID0
OFF
ON
OFF
ON
OFF
ON
OFF
ON
0
1
2
3
4
5
6
7
Connect the internal SCSI (LVD) cable (68P) to the drives.
Ⅵ The other end of the internal SCSI (LVD) cable is con-
nected to the SE-LVD conversion board.
*
ON
Internal SCSI cable (approx. 1.0 m)
Terminator
OFF
OFF
ON
<Interior of library>
Drive 4
Drive 3
ON
: Factory setting.
*
Procedure for Attaching the Drive
Drive 2
Drive 1
Storage Cover of the CD/DVD Library
1.
1.
Secure the cover with the screws that were removed.
"Procedure for Opening the Drive Storage Cover of
the CD/DVD Library" on page 3.
Terminator
Library SCSI board
Internal SCSI
(SE) cable
Procedure for Closing the CD/DVD
Library Door
To SE-LVD conversion board
<With the MC-8100LU>
Close the door and lock the key cylinder.
E
Download from Www.Somanuals.com. All Manuals Search And Download.
Procedure for Connecting the CD/DVD
Library to the Host Computer
EXECUTION OF AUTO-
MATIC DRIVE DETEC-
TION MODE.
Ⅵ Use an Ultra160-compatible cable as the external SCSI cable.
Execute the automatic drive detection mode of the
CD/DVD Library.
●
For the automatic drive detection mode, refer to the
instruction manual for the CD/DVD Library.
CAUTION
Ⅵ Be sure to close the drive storage cover and door of the
CD/DVD Library before turning it on.
Ⅵ After installing, adding, replacing or removing the drives,
be sure to execute the automatic drive detection mode.
Otherwise, a malfunction may result.
Ⅵ After installing, adding, removing or replacing the drives,
or changing the SCSI ID No., be sure to turn the host
computer off and then turn it on again.
To the host computer's
host adapter for
controlling the CD/DVD
Host computer
library
External SCSI cable
(commercially available)
(Ultral60 compatibly)
To the SCSI
connector
"IN" terminal
"SCSI-C"
Procedure for Executing the Automatic
Drive Detection Mode of the CD/DVD
Library
1.
While holding the "8" key on the control panel, turn the
power of the CD/DVD Library on.
CD/DVD library
2.
3.
When the LCD shows "DRIVE DETECTION COM-
PLETED," turn the power of the CD/DVD Library off.
Ⅵ The length of the SCSI cable built into the CD/DVD library is
1.0 meters.
Ⅵ When the built-in SCSI cable is used by connecting it to an
external SCSI cable, check the total length of the SCSI cable.
If it should exceed the length described below it might be the
cause of a malfunction.
1) Used for an LVD: The maximum external cable length
should be 10 meters.
2) Used for an SE (Narrow) unit:The maximum external cable
length should be as follows.
Turn the power on again and check the indication for the
drive type (DRIVE DISPLAY).
Ⅵ “DVD-RAM” will be displayed at the DRIVE DISPLAY on
the CD/DVD Library. If “UNKNOWN” is displayed, a cable
connection may not have been performed correctly. In
such a case, first turn off the power, then check the in-
stallation and connection again.
• SCSI-2, 10 Mbyte/s, SYNC : 1.5 meters (Up to a maxi
mum of 2 drives)
• SCSI-2, 10 Mbyte/s, SYNC : 1.5 meters
• SCSI-2, ASYNC
: 4.5 meters
Ⅵ Optimum performance may not be achieved depending on
the settings of the transmission rate, operation conditions,
etc., and could be the cause of a failure when writing on the
DVD-R or CD-R with high-speed.
Ⅵ Use an Ultra160-compatible cable as the external SCSI cable.
A malfunction may occur if any another type of cable is used.
Ⅵ Be sure to fasten the SCSI connector with suitable screws
after making a connection with an external SCSI cable.
E
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Ⅵ Interface
Ⅵ Applicable discs
Ultra 2 SCSI (80 Mbytes/s)
DVD-R 4.7 GB (Ver. 2.0 for General Use)
Recommended discs: Single-sided 4.7 GB
Matsushita Electric Corp.
Mitsubishi Kagaku Media Corp.
Hitachi Maxell Ltd.
Ⅵ Data transmission rate
Sustained (when the maximum sync transfer rate of the host adapter is
set to 80 Mbytes/s)
DVD-RAM
4.15 Mbytes/s (3X max.)
TDK Corp.
(Single-sided 4.7 GB or double-sided 9.4 GB)
Taiyo Yuden Co., Ltd.
DVD-RAM
1.38 Mbytes/s (1X)
(Single side 2.6 GB, read only)
Recommended discs: Double-sided 9.4 GB
Mitsubishi Kagaku Media Corp.
Hitachi Maxell Ltd.
DVD-R
5.44 Mbytes/s (4X max.) (write)
(Single-sided 4.7 GB or double-sided 9.4 GB)
DVD-R
8.31 Mbytes/s (6X max.) (read)
(Single-sided 4.7 GB or double-sided 9.4 GB)
DVD-ROM
(Single Layer, 12X max.: CAV)
16 Mbytes/s
DVD-R 3.95 GB (Ver. 1.0, Disc-at-once, read only)
DVD-ROM
DVD-RAM (Ver. 2.1, single-sided 4.7 GB, double-sided 9.4 GB)
Matsushita Electric Corp.
Hitachi Maxell Ltd.
DVD-RAM (Ver. 1.0, single-sided 2.6 GB, read only)
CD-ROM (Mode-1, Mode-2, etc.)
CD-R
CD-ROM
(32X max.: CAV)
CD-R
1.5 Mbytes/s to 4.8 Mbytes/s
Max. 1.8 Mbytes/s (write)
Max. 1.2 Mbytes/s (write)
(12X max.)
CD-RW
(8X max.)
Burst(when the maximum sync transfer rate of the host adapter is set to 80
Mbytes/s)
Ricoh Company Ltd.
Mitsubishi Kagaku Media Corp.
Hitachi Maxell Ltd.
Max. 10 Mbytes/s (sync transfer)
Ⅵ Average access time (1/3 stroke)
DVD-R (4.7 GB for General) : 145 ms
DVD-ROM (Single Layer) : 130 ms
TDK Corp.
Taiyo Yuden Co., Ltd.
Mitsui Chemicals, Inc.
DVD-RAM (4.7 GB)
DVD-RAM (2.6 GB)
CD-ROM
: 185 ms
: 195 ms
: 150 ms
CD-RW
Ricoh Company Ltd.
Mitsubishi Kagaku Media Corp.
*The above values were measured using JVC's measure
methods.
* Note 1: It is recommended to write and read the DVD-R,
DVD-RAM, CD-R and CD-RW discs using the drives
of the same model. If drives of different models
are used in write and read, discs of certain manu-
facturers or production lots may not manifest the
full performance.
Ⅵ Buffer capacity
2 Mbytes
Ⅵ Additional write count (DVD-R for General, 4.7 GB)
500 times typical (when a disc and a drive are combined)
15 times typical (when a disc and multiple drives are com bined)
* Note 2: Only discs with a diameter of 120 mm are appli-
cable.
* Note 3: Use DVD-R, CD-R and CD-RW discs that match the
optimal writing speed. However, even if the appro-
priate discs are used, an adequate performance
may not be achieved depending on the disc manu-
facturer or production lot compatibility.
Ⅵ Design and specifications are subject to change without no-
tice.
Ⅵ Dimensions
171 mm(W) x 47.5 mm(H) x 240 mm(D)
Ⅵ Weight
1.5 kg
Ⅵ Accessories
Drive locking screw ........................................................x 2
E
Download from Www.Somanuals.com. All Manuals Search And Download.
BEDIENUNGSANLEITUNG
MC-R434U
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONSREIHENFOLGE
Bitte führen Sie erforderlichen Installationsschritte in der angezeigten Reihenfolge durch.
INSTALLATION
Installieren Sie das MC-R434U in der CD/DVD-Bibliothek.
Ⅵ So öffnen Sie die Tür der CD/DVD-Bibliothek
●
Seite 3, 4
Ⅵ So öffnen Sie die Einbaubuchtabdeckung der CD/DVD-Bibliothek
Ⅵ Bestimmen der Einbaubucht für das MC-R434U
Ⅵ So installieren Sie das MC-R434U in der CD/DVD-Bibliothek
ANSCHLÜSSE
Schließen Sie das MC-R434U an die CD/DVD-Bibliothek an.
Ⅵ So schließen Sie die Kabel an die Rückseite von MC-R434U an
●
●
Seite 4, 5
Seite 5
EINRICHTEN
Stellen Sie die SCSI-ID-Nr. von MC-R434U ein und schließen Sie
die Tür der CD/DVD-Bibliothek
Ⅵ So stellen Sie den DIP-Schalter ein
Ⅵ So bringen Sie die Einbaubuchtabdeckung der CD/DVD-Bibliothek
wieder an
Ⅵ So schließen Sie die Tür der CD/DVD-Bibliothek
DURCHFÜHREN DER AUTOMATISCHEN
LAUFWERKERFASSUNG
Führen Sie die automatische Laufwerkerfassung durch und
schließen Sie den Hostcomputer an.
●
Seite 6
Ⅵ So führen Sie die automatische Laufwerkerfassung für die CD/DVD-
Bibliothek durch.
Ⅵ So schließen Sie die CD/DVD-Bibliothek an den Hostcomputer an.
SICHERHEITSHINWEISE VOR DEM GEBRAUCH
Das MC-R434U ist ein DVD-RAM/R-Laufwerk, das für den
Einsatz mit der JVC MC-8100LU/8200LU/8600LU "CD/DVD
Bibliothek" entwickelt wurde.
Soll dieses Laufwerk in einer Bibliothek installiert werden, die
in Gebrauch ist, bitte unbedingt die Bedienungsanleitung
sorgfältig lesen.
Die Umgebungstemperatur der CD/DVD-Bibliothek sollte im
Bereich von ca. 5°C bis 30°C liegen, wenn ein MC-R434U an
mehrere Geräte der Modellreihen MC-8100LU oder
MC8200LU/8600LU, wie nachfolgend angegeben,
angeschlossen ist.
●
●
●
• MC-8100LU
: 4 Geräte
Das MC-R434U-Laufwerk kann nicht getrennt betrieben
werden.
Dieses Laufwerk kann nicht zusammen mit den folgenden
Modellen verwendet werden
• CD-ROM-Bibliothek : MC-1000 Serie/2000 Serie
• DVD-RAM-Bibliothek : MC-7000 Serie
• CD/DVD-Bidliothek : MC-8000U serie
Angaben zu kompatiblen Diskausführungen finden Sie in den
Technischen Daten auf Seite 8.
• MC-8200LU/8600LU : 6 Geräte
●
●
1. GEFAHR: Unsichtbare Laserstrahlung, falls die
Sicherheitsverriegelung beim Öffnen versagt oder
abgestellt wird.
2. VORSICHT: Die obere Abdeckung darf nicht entfernt
werden. Im Inneren der Einheit befinden sich keine Teile, die
vom Benutzer gewartet werden können. Wartungsarbeiten
geschultem Servicepersonal überlassen.
●
G
Download from Www.Somanuals.com. All Manuals Search And Download.
So öffnen Sie die Einbaubuchtabdeckung
der CD/DVD-Bibliothek
INSTALLATION
Installieren Sie das MC-R434U in der CD/DVD-
Bibliothek.
●
Stellen Sie vor dem Einbau sicher, dass der Hostcomputer
und alle Peripheriegeräte ausgeschaltet sind.
Sonstige Angaben zum Einbau in die CD/DVD-
Bibliothek entnehmen Sie bitte der zu der CD/DVD-
Bibliothek gehörigen Bedienungsanleitung.
Laufwerkbucht
Schraube
Schraube
Einbaubuchtabdeckung
So öffnen Sie die Tür der CD/DVD-
Bibliothek
<Für MC-8100LU>
Laufwerkbucht
Montagebohrung
für Laufwerkmonta-
geschraube
Einbaubuchtabdeckung
Laufwerkbucht
Schraube
<Für MC-8100LU>
* In den Abbildungen wird die CD/DVD-Bibliothek zur erleichterten
Erläuterung ohne Einbaubuchtabdeckung gezeigt.
<Für MC-8200LU>
1.
2.
Entfernen Sie die Schrauben von der Einbaubuchtabdeckung
der CD/DVD-Bibliothek.
Laufwerkbucht
Nehmen Sie die Einbaubuchtabdeckung ab.
Bestimmen der Einbaubucht für das
MC-R434U
Montagebohrung
für Laufwerkmon-
tageschraube
Laufwerk Nr. 6
Laufwerk Nr. 5
Laufwerk Nr. 4
Laufwerk Nr. 3
Laufwerk Nr. 2
Laufwerk Nr. 1
Laufwerk Nr. 4
Laufwerk Nr. 3
Laufwerk Nr. 2
Laufwerk Nr. 1
<Für MC-8200LU>
1.
Wählen Sie in dem auf der LCD-Anzeige der CD/DVD-
Bibliothek dargestellten Menü den Eintrag [DOOR OPEN
MODE].
<
MC-8100LU Laufwerkbucht>
<
MC-8200LU Laufwerkbucht>
2.
3.
Halten Sie den Schalter “SELECT” für fünf Sekunden
gedrückt.
1.
Insallieren Sie die Laufwerke nacheinander in den
Laufwerkbuchten Nr.1 bis Nr. 6 (Nr. 1 bis Nr. 4 im Fall von
MC-8100LU).
Ⅵ Wenn Sie bei der untersten Einbaubuchtnummer
beginnen, vereinfachen Sie sich die Einbauarbeit.
Schalten Sie die Stromversorgung der CD/DVD-Bibliothek
aus, sobald die Meldung [THE DOOR CAN BE OPENED]
auf der LCD-Anzeige erscheint.
4.
Zum Entriegeln und Öffnen der Tür stecken Sie den
Schlüssel in das in derTürmitte befindliche Zylinderschloss.
G
Download from Www.Somanuals.com. All Manuals Search And Download.
So installieren Sie das MC-R434U in der
CD/DVD-Bibliothek
ANSCHLÜSSE
Schließen Sie das MC-R434U an die CD/DVD-
Bibliothek an.
●
Siehe auch die zur CD/DVD-Bibliothek gehörige
Bedienungsanleitung.
Sensorschlitz
So schließen Sie die Kabel an die
Rückseite von MC-R434U an
MC-R434U
Innenansicht
Terminator
Laufwerk 6
Laufwerk 5
Laufwerk 4
Laufwerk 3
Laufwerk 2
Laufwerk 1
Bibliothek-SCSI-Karte
Internes SCSI (LVD)-Kabel
<Einbaurichtung von MC-R434U>
MC-R434U
externer 68-pol. SCSI-Anschluss
An Hostcomputer (SE/LVD)
SE-LVD-Karte
Terminator
Internes SCSI (SE)-Kabel
Laufwerkmonta-
geschraube
<Anschlussbeispiel MC-R434U>
Steuerkabel
DIP-Schalter
<Befestigung von MC-R434U>
1
14p
1.
Setzen Sie das MC-R434U von der Rückseite der CD/DVD-
Bibliothek ein.
Ⅵ Achten Sie darauf, dass hierbei der Sensorschlitz nicht
beschädigt wird.
4p
2
Spannungs-
versorgung
3
SCSI-Kabel
Ⅵ Achten Sie auf die korrekte Einbaurichtung für das MC-
R434U.
<Rückseite von MC-R434U>
Ⅵ Achten Sie beim Einsetzen von MC-R434U darauf, dass
an der Rückseite der CD/DVD-Bibliothek befindliche
Kabel nicht eingeklemmt werden.
1.
Schließen Sie das Netzkabel, Steuerkabel und SCSI-Kabel
an die entsprechenden Anschlüsse auf der Rückseite des
MC-R434U an.
2.
3.
Schieben Sie das MC-R434U langsam ein, bis die seitlich
am MC-R434U befindliche Montagebohrung auf die
Montagebohrung der Laufwerkbucht ausgerichtet ist.
Ⅵ Bei Benutzung des MC-8100LU muß die Kabel-Nr.immer
der Nr. des Laufwerkeinschubs entsprechen, an dem es
angeschlossen ist. Wenn Laufwerke mit dem falschen
Einschub verbunden werden, kommt es zu
Fehlfunktionen.
Ⅵ Bei der Verwendung von Modellausführung MC-8200LU/
8600LU müssen die Steuerkabel verwendet werden, die
seitlich in das Einschubfach geführt werden, in dem MC-
R434U installiert werden soll.
Befestigen Sie die mitgelieferte Montageschraube in der
Montagebohrung der Laufwerkbucht .
Ⅵ Ziehen Sie die Schraube einwandfrei fest.
Ⅵ Bei einer lose angebrachten Montageschraube kann es
zu Schäden am Laufwerk und/oder der Bibliothek
kommen.
Ⅵ Überprüfen Sie die Stecker auf einwandfreien Sitz.
Ⅵ Die SCSI-Kabel müssen in Reihe angeschlossen
werden. Der Anschluss für die einzelnen Einbaubuchten
wird im Diagramm dargestellt.
• Der Abschluss des in den Standardmodellen MC-
8100LU/8200LU/8600LU eingebauten SCSI-Kabels
stimmt mit dem physischen Kabelabschluss überein.
G
Download from Www.Somanuals.com. All Manuals Search And Download.
EINRICHTEN
Stellen Sie die SCSI-ID-Nr. für das MC-R434U ein
und schließen Sie die Tür der CD/DVD-Bibliothek.
Sie müssen unbedingt die Stromversorgung der CD/
DVD-Bibliothek ausschalten, bevor Sie mit der
Einstellung der DIP-Schalter beginnen.
●
Angaben zur Grundeinstellung ab Werk siehe den
Abschnitt “SCSI ID Nr. SETTING” in der zur CD/DVD-
Bibliothek gehörigen Bedienungsanleitung.
< SE-LVD-Karte >
So stellen Sie den DIP-Schalter ein
Internes SCSI (SE)-Kabel
ON
4.
5.
50p
6p
ON
LVD-
Stromversorgungskabel
OFF
3.
1
2
3
4
6p
(Grundeinstellung ab Werk)
68p
Internes SCSI (LVD)-Kabel
An jedes Laufwerk
2.
Schließen Sie die beiden LVD-Stromversorgungskabel (6-
polig) an die SE-LVD-Karte an.
<MC-R434U DIP-Schalter-Einstellung an der Rückseite>
1.
ID2, ID1, ID0: Einstellung der SCSI-ID-Nr.für jedes Laufwerk.
Ⅵ Beide Kabel sind mit identischen Steckerausführungen
ausgerüstet und können dementsprechend beliebig an
einen der Anschlüsse der SE/LVD-Karte angebracht
werden.
Ⅵ Achten Sie darauf, keine SCSI-ID Nr. zu verwenden, die
bereits einem anderen SCSI-Peripheriegerät des
gleichen Busses zugewiesen wurde.
Ⅵ Dem MC-R434U muss eine der SCSI ID-Nummern 0
bis 7 zugewiesen werden. Die Nummern 8 bis 15 sind
ungeeignet.
3.
4.
Schließen Sie das interne SCSI (SE)-Kabel (50-polig) an
die SE-LVD-Karte an.
Ⅵ Das andere Ende des internen SCSI (SE)-Kabels ist an
die Bibliothek-SCSI-Karte in der Bibliothek
anzuschließen.
Ⅵ RSV: Nicht verfügbar.
<SCSI-ID-Nr.- und DIP-Schalter-Einstellungen>
Schalter
SCSI ID No.
ID2
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ID1
OFF
OFF
ON
ID0
OFF
ON
OFF
ON
OFF
ON
OFF
ON
Schließen Sie das interne SCSI (LVD)-Kabel (68-polig) an
die Laufwerke an.
Ⅵ Das andere Ende des internen SCSI (LVD)-Kabels ist
an die SE-LVD-Karte anzuschließen.
0
1
2
3
4
5
6
7
*
ON
OFF
OFF
ON
Internes SCSI-Kabel (ca. 1,0 m)
Terminator
< Innenansicht der Bibliothek >
Laufwerk 4
Laufwerk 3
ON
: Grundeinstellung ab Werk.
*
So bringen Sie die Einbaubuchtabdeckung
der CD/DVD-Bibliothek wieder an
Laufwerk 2
Laufwerk 1
1.
Bringen Sie die Einbaubuchtabdeckung mit den zuvor
entfernten Schrauben an.
Terminator
Bibliothek-SCSI-Karte
“So öffnen Sie die Tür der CD/DVD-Bibliothek” auf Seite 3
Internes SCSI
(SE)-Kabel
So schließen Sie die Tür der CD/DVD-
Bibliothek
An SE-LVD-Karte
<With the MC-8100LU>
1.
Schließen Sie die Tür ab.
G
Download from Www.Somanuals.com. All Manuals Search And Download.
So schließen Sie die CD/DVD-Bibliothek
an den Hostcomputer an
DURCHFÜHREN DER
AUTOMATISCHEN LAUF-
WERKERFASSUNG.
Ⅵ Als externes SCSI-Kabel muss eine 160-kompatible
Ausführung verwendet werden.
Führen Sie die automatische Laufwerkerfassung für
die CD/DVD-Bibliothek durch.
●
Angaben zum automatischen Lauwerks-
serkennungsmodus finden Sie in der zur CD/DVD-
Bibliothek gehörigen Bedienungsanleitung.
VORSICHT
An den Hostadapter
des Hostcomputers zur
Steuerung der
CD/DVD-Bibliothek
ⅥVergewissern Sie sich vor dem Einschalten der CD/DVD-
Bibliothek, dass die Einbaubuchtabdeckung befestigt
und die Tür der CD/DVD-Bibliothek geschlossen ist.
ⅥWenn Laufwerke installiert, hinzugefügt, ausgetauscht
oder entfernt wurden, muss unbedingt eine automatische
Laufwerkerfassung durchgeführt werden. Andernfalls
kann es zu Betriebsstörungen kommen.
ⅥWenn Laufwerke installiert, hinzugefügt, ausgetauscht
oder entfernt oder SCSI-ID-Nummern geändert wurden,
muss der Hostcomputer unbedingt aus- und erneut
eingeschaltet werden
Hostcomputer
Externes SCSI-Kabel
(im Fachhandel erhältlich)
(Ultra160-kompatible)
An den SCSI-
Anschluss,
“IN” Buchse
“SCSI-C”
So führen Sie die automatische Laufwerkerfassung für
die CD/DVD-Bibliothek durch
CD/DVD-Bibliothek
1.
Während Sie die Taste “8” auf der Bedientafel gedrückt
halten, schalten Sie die CD/DVD-Bibliothek ein.
Ⅵ Die Länge des in der CD/DVD-Bibliothek eingebauten SCSI-
Kabels beträgt 1,0 m.
Ⅵ Wird das interne SCSI-Kabel mit einem externen SCSI-Kabel
verbunden, muss die zulässige Gesamtlänge der SCSI-
Kabelverbindung berücksichtigt werden. Falls die zulässige
nachfolgend angegebene Gesamtlänge überschritten wird,
kann es zu Betriebsstörungen kommen.
1) Für LVD: Die maximal zulässige Länge des externen Kabels
beträgt 10 m.
2) Für SE (Eng): Für die maximal zulässige Länge des
externen Kabels gelten die folgenden Beschränkungen:
2.
3.
Wenn auf der LCD-Anzeige die Meldung “DRIVE DETEC-
TION COMPLETED” erscheint, schalten Sie die CD/DVD-
Bibliothek aus.
Schalten Sie nochmals ein und überprüfen Sie die Anzeige
für die Laufwerksausführung (DRIVE DISPLAY).
Ⅵ “DVD-RAM” wird für DRIVE DISPLAY an der CD/DVD-
Bibliothek angezeigt. Falls “UNKNOWN” angezeigt wird,
kann ein fehlerhafter Kabelanschluss vorliegen. In
diesem Fall zuerst ausschalten und anschließend den
Einbau und die Anschlüsse nochmals überprüfen.
• SCSI-2, 20 Mbyte/sYSNC : 1,5 Meter (Max. 2 Laufwerke)
• SCSI-2, 10 Mbyte/s SYNV : 1,5 Meter
• SCSI-2, ASYNC
: 4,5 Meter
Ⅵ Die maximal verfügbare Leistung kann ggf. in Abhängigkeit
von der Einstellung derTransferrate, den Betriebsbedingungen
etc., nicht erzielt werden. In diesem Fall kann es zu
Betriebsstörungen kommen, wenn Daten in hoher
Geschwindigkeit auf die DVD-R oder CD-R geschrieben
werden.
Ⅵ Als externes Kabel muss eine Ultra160-kompatible
Ausführung verwendet werden.BeiVerwendung einer anderen
Kabelausführung kann es zu Betriebsstörungen kommen.
Ⅵ Bei Anschluss eines externen SCSI-Kabels muss der
Steckverbinder mit geeigneten Schrauben befestigt werden.
G
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNISCHE DATEN
Ⅵ Schnittstelle
Ⅵ Geeignete Disks
Ultra 2 SCSI (80 Mbytes/Sek.)
DVD-R 4.7 GB (Ver. 2.0 für allgemeinen Gebrauch)
Empfohlene Disks: Einseitig 4,7 GB
Matsushita Electric Corp.
Mitsubishi Kagaku Media Corp.
Hitachi Maxell Ltd.
Ⅵ Datentransferrate
Unterbrechungsfrei (wenn der Hostadapter mit der maximalen Sync-
Transferrate von 20 Mbytes/Sek. arbeitet)
DVD-RAM
4,15 Mbytes/Sek. (3X max.)
TDK Corp.
(Einseitig 4,7 GB oder beidseitig 9,4 GB)
Taiyo Yuden Co., Ltd.
DVD-RAM
1,38 Mbytes/Sek. (1X)
(Einseitig 2,6 GB, nur lesen)
Empfohlene Disks: Beidseitig: 9,4 GB
Mitsubishi Kagaku Media Corp.
Hitachi Maxell Ltd.
DVD-R
5,44 Mbytes/Sek. (4X max.) (Schreiben)
(Einseitig 4,7 GB oder beidseitig 9,4 GB)
DVD-R
8,31 Mbytes/Sek. (6X max.) (Lesen)
(Einseitig 4,7 GB oder beidseitig 9,4 GB)
DVD-ROM
(Einzelschicht, 12X max.: CAV)
16 Mbytes/Sek.
DVD-R 3,95 GB (Ver. 1.0, Disc at once, nur lesen)
DVD-ROM
DVD-RAM (Ver. 2.1, einseitig 4,7 GB, beidseitig 9,4 GB)
Matsushita Electric Corp.
Hitachi Maxell Ltd.
DVD-RAM (Ver. 1.0, einseitig 2,6 GB, nur lesen)
CD-ROM (Modus 1, Modus 2 etc.)
CD-R
Ricoh Company Ltd.
Mitsubishi Kagaku Media Corp.
Hitachi Maxell Ltd.
CD-ROM
(32X max.: CAV)
1,5 Mbytes/Sek. bis 4,8 Mbytes/Sek.
CD-R
(12X max.)
Max. 1,8 Mbytes/Sek. (Schreiben)
Max. 1,2 Mbytes/Sek. (Schreiben)
CD-RW
(8X max.)
Burst(wenn der Hostadapter mit der maximalen Sync-Transferrate von 80
Mbytes/Sek. arbeitet)
Max. 10 Mbytes/Sek. (synchroner Datentransfer)
Ⅵ Durchschn. Zugriffszeit (1/3 Takt)
TDK Corp.
Taiyo Yuden Co., Ltd.
DVD-R (4,7 GB für allgemeine Anwendungen) : 145 ms
DVD-ROM (Einzelschicht)
DVD-RAM (4,7 GB)
DVD-RAM (2,6 GB)
CD-ROM
: 130 ms
: 185 ms
: 195 ms
: 150 ms
Mitsui Chemicals, Inc.
CD-RW
Ricoh Company Ltd.
Mitsubishi Kagaku Media Corp.
*Die obigen Angaben wurden nach JVC Messverfahren
erstellt.
* Hinweis 1: Es wird empfohlen, für DVD-R, DVD-RAM, CD-R
und CD-RW Disks stets sowohl im Schreib- als
auch im Lesebetrieb jeweils dieselbe Laufwerk-
Modellausführung zu verwenden. Werden für
den Schreib- und Lesebetrieb unterschiedliche
Laufwerk-Modellausführungen eingesetzt, kann
für Disks bestimmter Hersteller und/oder
Bauserien ggf. nicht die volle Leistung erzielt
werden.
Ⅵ Zwischenspeicher
2 Mbytes
Ⅵ Zählung zusätzlicher Schreibvorgänge (DVD-R für
allgemeine Anwendungen, 4,7 GB)
Typisch 500 Vorgänge (eine Disk und ein Laufwerk kombiniert)
Typisch15 Vorgänge (eine Disk und mehrere Laufwerke kombiniert)
* Hinweis 2: Es dürfen ausschließlich Disks mit einem
Durchmesser von 120 mm verwendet werden.
* Hinweis 3: Verwenden Sie DVD-R-, CD-R- und CD-RW-Disks, die
für die optimale Schreibgeschwindigkeit ausgelegt
sind. Bitte beachten Sie, dass selbst beiVerwendung
geeigneter Disks je nach Disk-Hersteller und infolge
von Produktionsschwankungen die maximal
verfügbare Leistung ggf. nicht erreicht werden kann.
Ⅵ Änderungen der Konstruktion und der technischen Daten
jederzeit ohne Vorankündigung vorbehalten.
Ⅵ Abmessungen
171 mm (B) x 47,5 mm (H) x 240 mm (T)
Ⅵ Gewicht
1,5 kg
Ⅵ Zubehör
Laufwerkmontageschraube ...........................................x 2
G
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUEL D’INSTRUCTIONS
MC-R434U
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Procédez comme suit pour l’installation.
INSTALLATION
Installez le MC-R434U dans la bibliothèque CD/DVD.
Ⅵ Ouverture de la porte de la bibliothèque CD/DVD
Ⅵ Ouverture du panneau de magasin des unités de la bibliothèque
CD/DVD
Ⅵ Détermination de l’emplacement du MC-R434U
Ⅵ Installation du MC-R434U dans la bibliothèque CD/DVD
●
Page 3, 4
Page 4, 5
Page 5
RACCORDEMENTS
Raccordez le MC-R434U à la bibliothèque CD/DVD.
Ⅵ Raccordement des câbles à l’arrière du MC-R434U
●
●
CONFIGURATION
Réglez le N˚ ID SCSI du MC-R434U et refermez la porte de la
bibliothèque CD/DVD.
Ⅵ Réglage des microcommutateurs
Ⅵ Fixation du panneau du magasin des unités de la bibliothèque CD/DVD
Ⅵ Fermeture de la porte de la bibliothèque CD/DVD
EXECUTION DU MODE DE DETECTION
AUTOMATIQUE DE LECTEUR
Exécution du mode de détection automatique de lecteur et
raccordement de l’ordinateur hôte.
●
Page 6
Ⅵ Exécution du mode de détection automatique de lecteur de la
bibliothèque CD/DVD
Ⅵ Raccordement de la bibliothèque CD/DVD à l’ordinateur hôte
PRECAUTIONS AVANT L’EMPLOI
Le MC-R433U est une unité DVD-RAM/R conçue pour être
utilisée avec la bibliothèque CD/DVD JVC MC-8100LU/
8200LU/8600LU.
A l’installation de cette unité dans une bibliothèque, lisez
attentivement le manuel d’instructions.
La température ambiante autour de la Bibliothèque CD/DVD
doit être maintenue à environ 5˚C à 30˚C quand un MC-R434U
est raccordé à plusieurs MC-8100LU ou MC8200LU/8600LU
dans la bibliothèque CD/DVD comme indiqué ci-dessous.
●
●
●
• MC-8100LU
: 4 unités
Le MC-R434U ne peut fonctionner de manière autonome.
Cette unité ne peut pas s’utiliser en combinaison avec les
modèles suivants:
• MC-8200LU/8600LU : 6 unités
●
●
1. DANGER: Rayonnement laser invisible en cas d’ouverture
avec une fermeture défaillante ou défectueuse.
2. ATTENTION: N’ouvrez pas le cache supérieur. Cet
appareil ne contient pas de pièces entretenables par
l’utilisateur; confiez tout l’entretien au personnel de ser-
vice qualifié.
• Bibliothèque CD/ROM : Série MC-1000/série 2000
• Bibliothèque DVD-RAM : Série MC-7000
• Bibliotheque CD/DVD
: Série MC-8000U
Voir les Spécifications à la page 8 pour les disques compatibles.
●
F
Download from Www.Somanuals.com. All Manuals Search And Download.
Ouverture du panneau de magasin des
unités de la bibliothèque CD/DVD
INSTALLATION
Installez le MC-R434U dans la bibliothèque CD/DVD.
Avant de commencer l’installation, mettez hors ten-
sion l’ordinateur hôte et tous les périphériques de la
bibliothèque.
Consultez le manuel d’instructions de la bibliothèque
CD/DVD pour les instructions la concernant.
●
Section magasin
à unités
Vis
Vis
Panneau de magasin
des unités
Ouverture de la porte de la bibliothèque
CD/DVD
<Avec le MC-8100LU>
Orifice pour vis de
verrouillage d’unité
Section magasin
des unités
Panneau de magasin
des unités
Section magasin
d’unité
Vis
<Avec le MC-8100LU>
* L’illustration indique la bibliothèque CD/DVD avec le panneau du
magasin des unités retiré pour faciliter la description.
<Avec le MC-8200LU>
1.
2.
Déposez les vis du panneau du magasin des unités de la
bibliothèque CD/DVD.
Section magasin
à unités
Déposez le panneau du magasin des unités.
Détermination de l’emplacement du
MC-R434U
Orifice pour vis
de verrouillage
d’unité
Unité n˚ 6
Unité n˚ 5
Unité n˚ 4
Unité n˚ 3
Unité n˚ 2
Unité n˚ 1
Unité n˚ 4
Unité n˚ 3
Unité n˚ 2
Unité n˚ 1
<Avec le MC-8200LU>
1.
2.
3.
Sélectionnez [DOOR OPEN MODE] dans l’écran MENU
sur l’affichage LCD de la bibliothèque CD/DVD.
Appuyez sur la commande “SELECT” pendant cinq
secondes.
<Section du magasin des
unités MC-8100LU>
<Section du magasin des
unités MC-8200LU>
Mettez la bibliothèque JVC hors tension quand le message
[THE DOOR CAN BE OPENED] apparaît sur l’affichage
LCD.
1.
Installez les unités dans les racks n˚1 à 6 (n˚1 à 4 pour le
MC-8100LU) dans cet ordre.
Ⅵ Installer les unités du numéro le plus bas vers le plus
haut facilite l’installation.
4.
Insérez la clé dans la serrure au centre de la porte pour
déverrouiller et ouvrir la porte.
F
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation du MC-R434U dans la
bibliothèque CD/DVD
RACCORDEMENTS
Raccordez le MC-R434U à la bibliothèque CD/DVD.
Consultez aussi le manuel d’instructions de la
bibliothèque CD/DVD.
●
Palpeur
Raccordement des câbles à l’arrière du
MC-R434U
MC-R434U
Intérieur
Terminaison
Unité 6
Câble SCSI (LVD) interne
Unité 5
<Direction d’installation du MC-R434U>
MC-R434U
Connecteur SCSI extérieur 68 broches
Unité 4
Vers l’ordinateur hôte (SE/LVD)
Carte de conversion SE-LVD
Unité 3
Unité 2
Unité 1
Terminaison
Carte SCSI de bibliothèque
Câble interne SCSI (SE)
<Example de raccordement du MC-R434U>
Vis de fixation
de l’unité
Câble de commande
Microcommutateurs
<Méthode de fixation du MC-R434U>
1
14p
4p
1.
Insérez le MC-R434U par l’arrière de la bibliothèque CD/
DVD.
2
Ⅵ Faites attention de ne pas endommager le palpeur.
Ⅵ Insérez le MC-R434U dans le sens correct.
Ⅵ Veillez à ce qu’aucun câble raccordé à l’arrière de la
bibliothèque CD/DVD ne soit coincé à l’introduction du
MC-R434U.
Câble
d’alimentation
3
Câble SCSI
<Panneau arrière du MC-R434U>
2.
3.
Insérez le MC-R434U lentement jusqu’à faire coïncider
l’orifice pour vis situé sur le côté du MC-R434U et l’orifice
pour vis de la section de fixation d’unité.
1.
Raccordez le câble d’alimentation, le câble de commande et
le câble SCSI aux connecteurs à l’arrière du MC-R434U.
Ⅵ Avec le MC-8100LU, le numéro du câble doit toujours
correspondre au numéro du rack du lecteur auquel il est
raccordé. Si vous connectez un câble portant un numéro
incorrect, l'appareil ne fonctionnera pas correctement.
Ⅵ Si vous utilisez le MC8200LU/8600LU, raccordez les
câbles de contrôle sortant du côté de la baie de l’unité là
où le MC-R434U doit être inséré.
Serrez la vis de fixation de l’unité fournie dans l’orifice pour
vis de la section de fixation d’unité.
Ⅵ Serrez fermement la vis.
Ⅵ Si la vis de fixation de l’unité est desserrée, l’unité et/ou
la bibliothèque peut être endommagée.
Ⅵ Raccordez fermement tous les connecteurs.
Ⅵ Les câbles SCSI sont raccordés en guirlande. Chaque
connecteur doit être raccordé à un emplacement d’unité,
comme le montre le croquis.
• Le câble SCSI, qui est intégré aux modèles standard
MC-8100LU/8200LU/8600LU, se termine à l’emplace-
ment où la connexion est physiquement terminée.
F
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION
Réglez le n˚ ID SCSI du MC-R434U et refermez la
porte de la bibliothèque CD/DVD.
●
Vérifiez que l’alimentation de la bibliothèque CD/DVD
est coupée au déplacement des microcommutateurs.
Pour les détails sur le réglage de cet appareil à la
sortie d’usine, voyez la section “DETERMINATION
DES N° ID SCSI” du mode d’emploi de la bibliothèque
CD/DVD.
Bibliothèque
<Carte de conversion SE-LVD>
Réglage des microcommutateurs
Câble SCSI (SE) interne
ON
4.
5.
50p
6p
ON
Câble
d’alimentation LVD
OFF
3.
1
2
3
4
6p
68p
(Sortie d’usine)
Câble SCSI (LVD) interne
A chaque unité
<Réglage des microcommutateurs du MC-R434U sur le
panneau arrière>
2.
Raccordez les deux câbles d’alimentation LVD (6P) à la
carte de conversion SE-LVD.
1.
ID2, ID1, ID0: Réglage du n˚ ID SCSI de chaque unité
Ⅵ Au réglage du n˚ ID SCSI, utilisez un numéro non utilisé
par d’autres périphériques SCSI du même bus.
Ⅵ Le MC-R434 doit être utilisé avec un SCSI à numéro
d’identification 0 à 7.Il n’est pas utilisable avec un numéro
de 8 à 15.
Ⅵ Les deux câbles ont des connecteurs de types
identiques, aussi l’un ou l’autre câble peut-il être connecté
à l’un ou l’autre connecteur sur la carte de conversion
SE-LVD.
3.
4.
Raccordez le câble SCSI (SE) interne (50P) à la carte de
conversion SE-LVD.
Ⅵ L’autre extrémité du câble interne SCSI (SE) est
raccordée à la carte SCSI de bibliothèque dans la
bibliothèque.
Ⅵ RSV: Non disponible
<Réglages du n˚ ID SCSI et des microcommutateurs>
Commutateur
N˚ ID SCSI
ID2
OFF
OFF
OFF
OFF
ON
ID1
OFF
OFF
ON
ID0
OFF
ON
OFF
ON
OFF
ON
OFF
ON
0
1
2
3
4
5
6
7
Raccordez le câble SCSI (LVD)(68P) aux unités.
Ⅵ L’autre extrémité du câble interne SCSI (LVD) est
raccordée à la carte de conversion SE-LVD.
*
ON
Câble SCSI interne (approx. 1,0 m)
Terminaison
< Intérieur de la bibliothèque >
OFF
OFF
ON
ON
ON
ON
Unité 4
Unité 3
ON
: Réglage usine
*
Fixation du panneau du magasin des
unités de la bibliothèque CD/DVD
Unité 2
Unité 1
1.
Fixez le panneau avec les vis retirées au cours de la
procédure
Terminaison
Carte SCSI de
bibliothèque
“Ouverture du panneau du magasin des unités de la
bibliothèque CD/DVD” à la page 3
Câble SCSI (SE)
interne
Fermeture de la porte de la bibliothèque
CD/DVD
A la carte de conversion SE-LVD
<With the MC-8100LU>
1.
Refermez la porte, puis verrouillez la serrure.
F
Download from Www.Somanuals.com. All Manuals Search And Download.
Raccordement de la bibliothèque CD/
DVD à l’ordinateur hôte
EXECUTION DU MODE DE
DETECTION AUTOMATIQUE
DE LECTEUR
Ⅵ Utilisez un câble compatible Ultra 160 comme câble SCSI
externe.
Exécutez le mode de détection automatique de lecteur
de la bibliothèque CD/DVD.
●
Consultez le manuel d’instructions de la bibliothèque CD/
DVD pour le mode de détection automatique de lecteur.
ATTENTION
ⅥRefermez bien le panneau du magasin des unités et la
porte de la bibliothèque CD/DVD avant la mise sous ten-
sion.
ⅥAprès l’installation, l’addition, le remplacement ou la
dépose d’unités, n’oubliez pas d’exécuter le mode de
détection automatique de lecteur.
Sinon un mauvais fonctionnement est possible.
ⅥAprès l’installation, l’addition, le remplacement ou la
dépose d’unités, ou le changement du n˚ ID SCSI,
mettez l’ordinateur hôte hors tension puis à nouveau
sous tension.
A l’adaptateur de
l’ordinateur hôte pour
Ordinateur hôte
le contrôle de la
bibliothèque CD/DVD
Câble SCSI externe
(disponible dans le commerce)
(Ultra160 comme câble)
A la borne
“IN”“SCSI-C”
du connecteur
SCSI
Exécution du mode de détection automatique
de lecteur de la bibliothèque CD/DVD
Bibliothèque CD/DVD
1.
Mettez la bibliothèque sous tension en maintenant la tou-
che "8" du panneau de commande pressée.
<Exemple de connexion de système 2 de câble SCSI>
Ⅵ La longueur du câble SCSI intégré à la bibliothèque CD-DVD
est de 1,0 m.
Ⅵ Quand le câble SCSI intégré est utilisé en le raccordant à un
câble SCSI externe, vérifiez la longueur totale du câble SCSI.
Si elle dépasse la longueur indiquée ci-dessous, cela peut
provoquer un mauvais fonctionnement.
1) Utilisé pour un LVD: La longueur maximale du câble externe
doit être de 10 mètres.
2) Utilisé pour une unité SE (étroit): La longueur maximale du
câble externe doit être comme suit.
2.
3.
Mettez la bibliothèque hors tension quand l'affichage LCD
indique "DRIVE DETECTION COMPLETED".
Remettez sous tension et vérifiez l’indication du type d’unité
(DRIVE DISPLAY).
Ⅵ “DVD-RAM” s’affichera à DRIVE DISPLAY de la
bibliothèque CD-DVD. Si “UNKNOWN” s’affiche, un
raccordement de câble peut être incorrect. Dans ce cas,
mettez d’abord hors tension, puis revérifiez l’installation
et le raccordement.
• SCSI-2, 20 Mo/s, SYNC : 1,5 m (2 unités max.)
• SCSI-2, 10 Mo/s, SYNC : 1,5 m
• SCSI-2, ASYNC
: 4,5 m
Ⅵ La performance optimale peut ne pas être obtenue selon les
réglages du débit, des conditions d’exploitation etc. et pourrait
être la cause d’une défaillance à l’écriture à grande vitesse
sur le DVD-R ou CD-R.
Ⅵ Utilisez un câble compatible Ultra160 comme câble SCSI
externe. Un mauvais fonctionnement est possible à l’emploi
d’un autre câble.
Ⅵ Fixez bien le connecteur SCSI avec des vis convenables après
le raccordement avec un câble SCSI externe.
F
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Ⅵ Interface
Ⅵ Disques applicables
DVD-R 4.7 GB (Ver. 2.0 à usage général)
Disques recommandés: Une face 4,7 Go
Matsushita Electric Corp.
Mitsubishi Kagaku Media Corp.
Hitachi Maxell Ltd.
Ultra 2 SCSI (80 Mo/sec.)
Ⅵ Vitesse de transfert
Soutenu (quand la vitesse de transfert synchro maximum de l’adaptateur
maître est réglée à 80 Mo/sec.)
DVD-RAM
4,15 Mo/sec. (3X max.)
TDK Corp.
(4,7 Go une face ou 9,4 Go deux faces)
Taiyo Yuden Co., Ltd.
DVD-RAM
1,38 Mo/sec. (1X)
(2,6 Go une face, lecture seulement)
Disques recommandés: double face 9,4 Go
Mitsubishi Kagaku Media Corp.
Hitachi Maxell Ltd.
DVD-R
5,44 Mo/sec. (4X max.) (inscription)
(Une face 4,7 Go ou double face 9,4 Go)
DVD-R
8.31 Mo/sec. (6X max.) (lecture)
(Une face 4,7 Go ou double face 9,4 Go)
DVD-R 3.95 GB (Ver. 1.0, Disc at once, lecture seulement)
DVD-ROM
DVD-ROM
(Une couche, 12X max. : CAV)
CR-ROM
16 Mo/sec.
DVD-RAM (Ver. 2.1, une face 4,7 Go, double face 9,4 Go)
Matsushita Electric Corp.
Hitachi Maxell Ltd.
1,5 à 4,8 Mo/sec.
(32X max: CAV)
CD-R
1,8 Mo/s max. (inscription)
1,2 Mo/s max. (inscription)
DVD-RAM (Ver. 1.0, une face 2,6 Go, lecture seulement)
CD-ROM (Mode-1, Mode-2, etc.)
CD-R
(12X max.)
CD-RW
(8X max.)
Ricoh Company Ltd.
Salve (quand la vitesse de transfert synchro maximum de l’adaptateur maître
est réglée à 80 Mo/sec.)
Mitsubishi Kagaku Media Corp.
Hitachi Maxell Ltd.
10 Mo/sec. max. (transfert synchrone)
TDK Corp.
Taiyo Yuden Co., Ltd.
Ⅵ Temps d’accès moyen (1/3 segment)
Mitsui Chemicals, Inc.
DVD-R (4,7 Go pour ordinaire)
DVD-ROM (une couche)
DVD-RAM (4,7 Go)
DVD-RAM (2,6 Go)
CD-ROM
:145 ms
:130 ms
:185 ms
:195 ms
:150 ms
CD-RW
Ricoh Company Ltd.
Mitsubishi Kagaku Media Corp.
* Remarque 1: Il est recommandé de graver et de lire les
disques DVD-R, DVD-RAM, CD-R et CD-RW
en utilisant des lecteurs du même modèle.
Si des lecteurs de modèles différents sont
utilisés pour la gravure et la lecture, les
disques de certains fabricants ou lots de
production peuvent ne pas assurer
totalement leurs performances.
*Les valeurs ci-dessus ont été mesurées avec la méthode
de mesure JVC.
Ⅵ Capacité tampon
2 Mo
Ⅵ Comptage d’écriture additionnel (DVD-R pour ordinaire,
4,7 Go)
* Remarque 2: Seuls les disques à diamètre de 120 mm
sont applicables.
500 fois typique (quand un disque et une unité sont combinés)
15 fois typique (quand un disque et plusieurs unités sont combinés)
* Remarque 3: Utiilisez des DVD-R, CD-R et CD-RW
conformes à la vitesse d'inscription
optiimale. Même si des disques appropriés
sont utilisés, des performances adéquates
peuvent ne pas être obtenues selon le
fabricant de disque ou la compatibilité du
lot de production.
Ⅵ Dimensions
(lxhxp) 171 x 47,5 x 240 mm
Ⅵ Poids:
1,5 kg
Ⅵ Accessoires
Ⅵ Conception et spécifications sont sujettes à modification sans
Vis de fixation d’unité........................................................x2
préavis.
F
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD-RAM/R驱动器
使用说明书
MC-R434U
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢁ !
ꢀꢁ !"#$%&'(
ꢀꢁ
ꢀ j`JoQPQr ꢀꢁ `aLasa ꢀꢁ !
Ⅵ ꢀꢁ !"#$%
Ⅵ ꢀꢁ !"#$%&'(
Ⅵ ꢀꢁ j`JoQPQr ꢀꢁ !"
Ⅵ ꢀꢁ j`JoQPQr
●
==ꢀPꢀꢁ
ꢀꢁ
ꢀꢁ j`JoQPQr ꢀ `aLasa ꢀꢁ !"#$%
Ⅵ ꢀꢁ j`JoQPQr ꢀꢁ !"
●
●
==ꢀ Qꢀꢁꢀ
==ꢀ R ꢀ
ꢀꢁ
ꢀꢁ j`JoQPQr ꢀ p`pf ꢀꢁ !ꢀꢁ !"#$%&'(
Ⅵ ꢀꢁ !"#$%&
Ⅵ ꢀꢁ !"#$%&'(
Ⅵ ꢀꢁ !"#$%
ꢀꢁ !ꢁ"#
ꢀꢁ !"#!$%&'()*+,-./0
Ⅵ ꢀꢁ !"#$ꢁ%&ꢁ'()*+
Ⅵ ꢀꢁ !"#$%&'()
●
==ꢀ S ꢀ
ꢀꢁ !"#$%
ꢀꢁ !" gs`ꢀ`aLasa ꢀꢁ !j`JUNMMirLUOMMirL
USMMir ꢀꢁ asaJo^jLo ꢀꢁ !
=ꢀꢁ !"#$%&'()*+,-./ꢀꢁ !"#$%&
ꢀꢁ
ꢀꢁ`aLasaꢀꢁ !"#$%&'()j`JoQPQrꢀꢁ
ꢀꢁꢀꢁ R ꢀꢁ PM ꢀꢁ !"#$%&'(
ꢀ=j`JUNMMirꢀQꢀ
●
●
●
ꢀ=j`JUOMMirLUSMMirꢀSꢀ
=ꢀꢁ !"#$%&'(
=ꢀꢁ !"#$%&'()*ꢀ
ꢀ=`aJolj ꢀꢁ ꢀj`JNMMM ꢀꢁ j`JOMMM ꢀꢁ
ꢀ=asaJo^j ꢀꢁ ꢀj`JTMMM ꢀꢁ
●
●
ꢀ=`aLasa ꢀꢁ ꢀj`JUMMMr ꢀꢁ
ꢀꢁ !ꢁ"#$%&'()*+,-$./01
NK ꢀꢁꢀꢀꢁ !"#$ꢀꢁ !"#$%ꢁ&'()*+
ꢀꢁꢀꢁ !"#$%&'()*+
●
OK ꢀꢁꢀꢀꢁ !"#$%ꢀꢁ !"#$%&'()!
ꢀꢁꢀꢁ !"#$%&'()
`
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢁ !"#$%&'(
ꢀꢁ
ꢀ j`JoQPQr ꢀꢁ `aLasa ꢀꢁ !
ꢀꢁ !"#$%&'()*+,-./ꢁ01234
ꢀꢁ `aLasa ꢀꢁ !"#$%&ꢀꢁ !'("
ꢀꢁ
●
驱动器仓
螺钉
螺钉
驱动器仓门
ꢀꢁ !"#$%
ꢀj`JUNMMirꢀ
驱动器固定螺孔
驱动器仓
驱动器仓门
驱动器仓
螺钉
ꢀj`JUNMMirꢀ
ꢀj`JUOMMirꢀ
G ꢀꢁ !"#$ꢀꢁ !"#$%&'()*ꢁ+,
1.
2.
ꢀꢁ !"#$%&'()*
ꢀꢁ !"#$%
驱动器仓
ꢀꢁ j`JoQPQr ꢀꢁ !"
驱动器固定螺孔
驱动器 No. 6
驱动器 No. 5
驱动器 No. 4
驱动器 No. 3
驱动器 No. 2
驱动器 No. 1
驱动器 No. 4
驱动器 No. 3
驱动器 No. 2
驱动器 No. 1
ꢀj`JUOMMirꢀ
1.
ꢀ `aLasa ꢀꢁ !"#$%&'$%()*+,ꢀꢁ
ꢀꢀallo=lmbk=jlabꢀꢁ
ꢀj`JUNMMir ꢀꢁ !"#
ꢀj`JUOMMir ꢀꢁ !"#
2.
3.
ꢀꢁ R ꢀꢁ !ꢀpbib`qꢀꢀꢁ
1.
ꢀꢁ kçK=N ꢀ kçK=Sꢀj`JUNMMirꢀkçK=N ꢀ kçK=Qꢀꢀꢁ
ꢀꢁ !"#$
ꢀꢁ !"# !$ꢀqeb=allo=`^k=_b=lmbkbaꢀꢀ
ꢀꢁ !"#$%&
Ⅵ ꢀ kçK=N ꢀꢁ !"#$%&'()*+$,-./0
4.
ꢀꢁ !"#$%&'ꢁ ()*+#$,
ꢀꢁ
`
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢁ j`JoQPQr
ꢀꢁ
ꢀꢁ j`JoQPQr ꢀ `aLasa ꢀꢁ !"#$%&
ꢀꢁ !" `aLasa ꢀꢁ !"#$%&'
●
传感器口
ꢀꢁ j`JoQPQr ꢀꢁ !"
MC-R434U
ꢀj`JoQPQr ꢀꢁ !"#
MC-R434U
ꢀj`JoQPQr ꢀꢁ !"#
驱动器固定螺钉
控制电缆
ꢀj`JoQPQr ꢀꢁ !"#
1
14p
W
N
双列直插式开关
电源电缆
1.
ꢀꢁ !"#$% j`JoQPQr ꢀꢁ !
Ⅵ ꢀꢁ !"#$%&'()
Ⅵ ꢀꢁ j`JoQPQr ꢀꢁ !"#
4p
2
3
SCSI电缆
Ⅵ ꢀꢁ j`JoQPQr ꢀꢁ !"#$%&'()*+,-.
ꢀj`JoQPQr ꢀꢁ !
2.
3.
ꢀꢀꢁ ! j`JoQPQr ꢀꢁ !ꢀꢁ !"#$%&'(
ꢀꢁ !"#$
1.
ꢀꢁ ꢁ!"ꢀꢁ !"p`pf ꢀꢁ ! j`JoQPQr ꢀꢁ
ꢀꢁ !
Ⅵ=ꢀꢁj`JUNMMirꢀꢁ !"ꢀꢁ !"#$%&'()
ꢀꢁ !"#$%&'(ꢀꢁ !"#$%&'()*ꢀ
ꢀꢁ !"#$%&
ꢀꢁ !"#$%&'()*+&'#$%",*-./
Ⅵ ꢀꢁ !"#$%
Ⅵ ꢀꢁ !"#$%&'()*+,-
Ⅵ=ꢀꢁj`JUOMMirLUSMMirꢀꢁꢀꢁ !"#j`JoQPQr
ꢀꢁ !"#ꢀ$%&'(
Ⅵ=ꢀꢁ !"#$%&'(
Ⅵ=p`pfꢀꢁ !"#$%&'()ꢀꢁ !"#$%&'
ꢀꢁ !
ꢀj`JUNMMirLUOMMirLUSMMirꢀꢁ p`pfꢀꢁ !"
ꢀꢁ !"#
`
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢁ
ꢀꢁ j`JoQPQr ꢀ p`pf ꢀꢁ !ꢀꢁ !"#$%
ꢀꢁ
●
ꢀꢁ !"#$%&'(ꢁ)*+ `aLasa ꢀꢁ
ꢀꢁ !
ꢀꢁ !"#$%&'()*+ !",-./01
ꢀꢀp`pf ꢀꢁ !"#$ꢀꢁ
ꢀꢁ !"#$%&
ON
4.
5.
ON
50p
6p
6p
OFF
3.
1
2
3
4
68p
ꢀj`JoQPQr ꢀꢁ !"#$%&'()*
2. ꢀꢁ ! isa ꢀꢁꢀ ꢀSmꢀꢀ pbJisa ꢀꢁ !
• ꢀꢁ !"#$%ꢀꢁ !"#$%
1.
ꢀ faOꢀfaN ꢀ faM ꢀꢁ !"# p`pf ꢀꢁ !
Ⅵ=ꢀꢁ !"#$%&'()*+,p`pfꢀꢁ !"#$
ꢀꢁ !"#$%
Ⅵ=j`JoQPQr ꢀꢁ ! p`pf ꢀꢁ M ~ Tꢀꢀꢁ ! U ~
NR ꢀꢁ !"#$
3. ꢀꢁ ! p`pfꢀpbꢀꢀꢁꢀRMmꢀꢀ pbJisa ꢀꢁ !
• ꢀꢁ p`pfꢀpbꢀꢀꢁ !"#$%&'( p`pf ꢀꢁ
Ⅵ=opsW=ꢀꢁ
4. ꢀꢁ ! p`pfꢀisaꢀꢀꢁꢀSUmꢀꢀꢁ !"#
• ꢀꢁp`pꢀf isaꢀꢁ !"#$%&pbJisaꢀꢁ !"
ꢀp`pf ꢀꢁ !"#$%&'()*+,
ꢀꢁ !"#$
p`pf ꢀꢁ
faO
lcc
lcc
lcc
lcc
lk
lk
lk
lk
faN
lcc
lcc
lk
lk
lcc
lcc
lk
lk
faM
lcc
lk
lcc
lk
lcc
lk
lcc
lk
M
N
G
O
P
Q
R
S
T
ꢀꢁ ꢀꢁ !"#$%& '()
G
ꢀꢁ !"#$%&'(
1.
1.
ꢀꢁ !"#$%&'()
ꢀ P ꢀꢀꢁ !"#$%&'()*
ꢀꢁ !"#$%
ꢀꢁ !"ꢀꢁ ꢀ!
`
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢁ !"#$%&'(
ꢀꢁ !ꢁ"#
Ⅵ ꢀꢁ p`pf ꢀꢁ !" räíê~NSM ꢀꢁ !"#
ꢀꢁ !"#!$%&'(
●
ꢀꢁ !"#!$%&'()*+,-./`aLasa
ꢀꢁ !"#$%&'
ꢀꢁꢀ
Ⅵ ꢀꢁ !"#$%&'()*+,-./0ꢀꢁ !"
ꢀꢁ
Ⅵ ꢀꢁ !ꢀꢁ !"#$%&'( !")!*+,ꢀ
ꢀꢁ !"#$%&'
Ⅵ ꢀꢁ !ꢀꢁ !"#$%& p`pfꢀꢁ !"#$%
ꢀꢁ !"#$%&'()
ꢀꢁ !"#$ꢁ%&ꢁ'()*
1.
ꢀꢁ !"#$%&'()* +ꢀUꢀꢀꢁ !"#$
2.
ꢀꢁ !"# !$ꢀaofsb=abqb`qflk=`ljmibqbaꢀ
ꢀꢁ !"#
3.
ꢀꢁ !"#$%&'()*+,-./aofsb=afpmi^vꢀꢁ
Ⅵ=ꢀ`aLasaꢀꢁ !"#$%&'%&ꢀasaJo^jꢀꢁ
ꢀꢁ !"ꢀrkhkltkꢀꢀꢁ !ꢀꢁ !"#$%&
ꢀꢁ !"#$%&'()*+,-.
Ⅵ `aLasaꢀꢁ !"#p`pfꢀꢁ !"#NKMꢀꢁ
Ⅵ ꢀꢁ !"#$p`pfꢀꢁ !"p`pfꢀꢁ !"#$%"&'
ꢀꢁ !"#$%&'()*+
ꢀꢁ !"#$%&'(
NF=ꢀꢁisaꢀꢁ !"#$%&'()*+NMꢀꢁ
OF=ꢀꢁpbꢀꢁ !"#$%&'()*+,-./0
ꢀp`pfJOI=OM=jÄóíÉëLë=ꢀꢁ NKRꢀꢁ !"#$%&'()*
ꢀp`pfJOI=NM=jÄóíÉëLë=ꢀꢁ NKRꢀ
ꢀp`pfJOI=ꢀꢁ !QKRꢀ
Ⅵ ꢀꢁ !"#$%&'()*+,+-./0"#1*+23
asaJoꢀ`aJoꢀꢁ !"#$%
Ⅵ ꢀꢁp`pfꢀꢁ !"räíê~NSMꢀꢁ !"#$%&'()*
ꢀꢁ
ꢀꢁ !"#$%
Ⅵ ꢀꢁp`pfꢀꢁ !"#$%&p`pfꢀꢁ !"#$%&'(
ꢀꢁ
`
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢁ
Ⅵ ꢀꢁꢀräíê~=O=p`pf=E=UM=jÄóíÉëLë=F
Ⅵ ꢀꢁ !
asaJo==QKT=d_ꢀsÉêK=OKM ꢀꢁ !
ꢀꢁ !"#$ QKT=d_
j~íëìëÜáí~=bäÉÅíêáÅ=`çêéK
jfqpr_fpef=h^d^hr=jbaf^=`lKI=iíÇK
eáí~ÅÜá=j~ñÉää=iíÇK
Ⅵ ꢀꢁ !"
ꢀꢁꢀꢁ !"#$%&'()*+,- UM=jÄóíÉëLë ꢀꢁ
asaJo^j
ꢀꢁ QKT=d_ꢀꢀꢁ VKQ=d_ꢀ
QKNR=jÄóíÉëLëꢀꢁ P ꢀꢁ
asaJo^j
ꢀꢁ OKS=d_ꢀꢀꢁ !"
NKPU=jÄóíÉëLëꢀꢁ O ꢀꢁ
qah=`çêéK
q~áóç=vìÇÉå=`çKI=iíÇK
asaJo RKQQ=jÄóíÉëLëꢀꢁ Qꢀꢁ ꢀꢁ !
ꢀꢁ QKT=d_ꢀꢀꢁ VKQ=d_ꢀ
ꢀꢁ !"#$ VKQ=d_
jfqpr_fpef=h^d^hr=jbaf^=`lKIiíÇK
eáí~ÅÜá=j~ñÉää=iíÇK
asaJo
ꢀꢁUKPN=jÄóíÉëLꢀë ꢁ Sꢀꢁ ꢀꢁ !
ꢀꢁ QKT=d_ꢀꢀꢁ VKQ=d_ꢀ
asaJolj
ꢀꢁ !
NS=jÄóíÉëLë
asaJo=PKVR=d_ꢀsÉêK=NKMꢀꢀꢁ !"#ꢀꢁ !"
asaJolj
~
`aJolj
ꢀꢁ PO ꢀꢁꢀ`^sꢀ
NKR=jÄóíÉëLë= =QKU=jÄóíÉëLë
asaJo^jꢀsÉêK=OKNꢀꢀꢁ QKT=d_ꢀꢀꢁ VKQ=d_ꢀ
j~íëìëÜáí~=bäÉÅíêáÅ=`çêéK
jáíëìÄáëÜá=h~Ö~âì=jÉÇá~=`çêéK
asaJo^jꢀsÉêK=NKMꢀꢀꢁ OKS=d_ꢀꢀꢁ !"
`aJoljꢀjçÇÉJNꢀjçÇÉJO ꢀꢁ
`aJo
`aJo
ꢀꢁ NKU=jÄóíÉëLëꢀꢁ !
ꢀꢁ NKO=jÄóíÉëLëꢀꢁ !
ꢀꢁ NO ꢀꢁ
`aJot
ꢀꢁ U ꢀꢁ
ꢀꢁꢀꢁ !"#$%&'()*+,- UM=jÄóíÉëLë ꢀꢁ
ꢀꢁ !"ꢀ==ꢀꢁNM=jÄóíÉëLë
oáÅçÜ=`çãé~åó=iíÇK
jáíëìÄáëÜá=h~Ö~âì=jÉÇá~=`çêéK
eáí~ÅÜá=j~ñÉää=iíÇK
qah=`çêéK
q~áóç=vìÇÉå=`çKI=iíÇK
jáíëìá=`ÜÉãáÅ~äëI=fåÅK
`aJot
oáÅçÜ=`çãé~åó=iíÇK
jáíëìÄáëÜá=h~Ö~âì=jÉÇá~=`çêéK
Ⅵ ꢀꢁ !"#ꢀNLP ꢀꢁ
asaJoꢀQKT=d_ꢀꢀꢁ !ꢀNQR=ãë
asaJoljꢀꢁ !
asaJo^jꢀQKT=d_ꢀ
asaJo^jꢀOKS=d_ꢀ
`aJolj
ꢀNPM=ãë
ꢀNUR=ãë
ꢀNVR=ãë
ꢀNRM=ãë
G ꢀꢁ !"# gs` ꢀꢁ !"#
Ⅵ ꢀꢁ !"#
G=ꢀ N W ꢀꢁ !"#$%&'()&'*+, a s a J o ꢀ
asaJo^jꢀ`aJoꢀ `aJotꢀꢀꢁ !"#$%&
ꢀꢁ !"ꢀꢁ !"#$ꢀꢁ !%&'()*+
ꢀꢁ !"#$%&
G=ꢀ O W ꢀꢁ !"#$%& NOM=ãã ꢀꢁ !
G=ꢀ P W ꢀꢁ asaJoꢀ`aJoꢀ`aJotꢀꢁ !"#$%&
ꢀꢁ !"#ꢀꢁ !"#$%&'()%&*+,
ꢀꢁꢀꢁ !"#$%&'(&)*+
O=jÄóíÉëLë
Ⅵ ꢀꢁ !"#ꢀQKT=d_ ꢀꢁ asaJoꢀ
RMM ꢀꢀꢁ !"#$ꢁ %&'()&'*+,-./0
NR ꢀꢀꢁ !"#$%&'()*'(+,-./01
Ⅵ ꢀꢁ !
OQM=ããꢀꢁ ꢀ NTN=ããꢀꢁ ꢀ QTKR=ããꢀꢁ
Ⅵ ꢀꢁ !"#$%&'()*+,ꢀꢁ !"#$
Ⅵ ꢀꢁ
NKR=âÖ
Ⅵ ꢀꢁ
ꢀꢁ !"#$ KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKO
`
Download from Www.Somanuals.com. All Manuals Search And Download.
|