JVC CRT Television AV28WT5EI AV24WT5EI User Manual

Colour Television

AV28WT5EI

AV24WT5EI

Contents

Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Setting up your TV . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

T-V LINK functions. . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Using your TV–the basics . . . . . . . . . . . . . . . . . . . . . 8

Remote control buttons and functions . . . . . . . . . . . . 11

Using the TV’s menus . . . . . . . . . . . . . . . . . . . . . . . 16

Picture setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Picture features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Sound setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

EXT SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

INSTALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

DEMO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Other menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Further preparation . . . . . . . . . . . . . . . . . . . . . . . . . 30

TV buttons and parts . . . . . . . . . . . . . . . . . . . . . . . . 32

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

INSTRUCTIONS

Download from Www.Somanuals.com. All Manuals Search And Download.

Thank you for buying this

colour television.

To make sure you fully understand how to use your new TV, please read this manual thoroughly before you begin.

6DIHW\#SUHFDXWLRQV

■ :DUQLQJ

■

:DUQLQJ

To prevent fire or shock hazard, do not expose this

appliance to rain or moisture.

DO NOT cut off the mains plug from this equipment. If the

plug fitted is not suitable for the power points in your home or

the cable is too short to reach a power point, then obtain an

appropriate safety approved extension lead or adaptor or

consult your dealer.

■

&DXWLRQ

To ensure personal safety, observe the following rules

regarding the use of this unit.

If nonetheless the mains plug is cut off, remove the fuse and

dispose of the plug immediately, to avoid a possible shock

hazard by inadvertent connection to the mains supply.

1 Operate only from the power source specified (AC 220 –

240 V, 50 Hz) on the unit.

2 Avoid damaging the AC plug and power cord.

3 Avoid improper installation and never position the unit

where good ventilation is unattainable.

When installing this television, distance recommendations

must be maintained between the floor and wall, as well as

instalment in a tightly enclosed area or piece of furniture.

Please adhere to the minimum distance guidelines shown

for safe operation.

If a new mains plug has to be fitted, then follow the instruction

given below:

Important

Do not make any connection to the larger terminal which is

marked with the letter E or by the safety earth symbol or

coloured green or green-and-yellow.

The wires in the mains lead on this product are coloured in

accordance with the following code:

Blue: Neutral

15 cm

Brown: Live

As these colours may not correspond with the coloured

marking identifying the terminals in your plug proceed as

follows:

10 cm

15 cm

4 Do not allow objects or liquid into the cabinet openings.

5 In the event of a fault, unplug the unit and call a service

technician. Do not attempt to repair it yourself or remove

the rear cover.

The wire which is coloured blue must be connected to the

terminal which is marked with the letter N or coloured black.

6 The surface of the TV screen is easily damaged. Be very

careful with it when hendling the TV.

Should the TV screen become soiled, wipe it with a soft dry

cloth. Never rub it forcefully. Never use any cleaner or

detergent on it.

7 When you don’t use this TV set for a long period of time, be

sure to disconnect the power plug from the AC outlet.

8 Do not hold the front panel door when moving the TV, if you

do you may break it.

The wire which is coloured brown must be connected to the

terminal which is marked with the letter L or coloured red.

When replacing the fuse only a correctly rated approved type

should be used and be sure to re-fit the fuse cover.

If in doubt — consult a competent

electrician.

How to replace the fuse

Open the fuse compartment

with a blade screwdriver, and

replace the fuse.

Fuse

Download from Www.Somanuals.com. All Manuals Search And Download.

■

*XLGHOLQHV#IRU#VDIH#RSHUDWLRQ

This equipment has been designed and manufactured to comply with international safety standards. However, as with any

electrical appliance, care must be taken to ensure optimal results and operational safety.

• Before attempting to use this equipment, read the operating instructions thoroughly.

• Ensure that all electrical connections (including the mains plug, extension leads, etc.) have been made in accordance with the

manufacturer’s instructions.

• If ever in doubt about the installation, operation or safety of this equipment, consult your dealer.

• Handle all glass panels or covers with care.

• Never operate this equipment if it appears damaged or operates abnormally. Turn the power off, disconnect the main power

plug and consult your dealer.

• Never remove any affixed panels or covers. Doing so may result in electrical shock.

• Never leave this equipment operating unattended unless otherwise specifically stated that it is designed to do so or in standby

mode. Only use the designated power switch to turn off the power and ensure that all potential users are instructed how to do

so. Make special arrangements for infirm or handicapped persons.

• Never watch TV while operating a motor vehicle. It is illegal to watch TV while driving.

• Never listen to headphones at high volume. Doing so may damage your hearing.

• Never obstruct the ventilation of this equipment. Doing so may cause overheating and result in a malfunction or damage.

• Never use makeshift stands or attempt to affix legs with wood screws. When using a manufacturer’s approved stand or legs,

use only the fixtures provided and follow the installation instructions.

• Never allow this equipment to be exposed to rain or moisture.

• Never allow anyone, especially children, to insert anything into an opening in the case. Doing so may result in a fatal electrical

shock.

• Never guess or take chances with electrical equipment of any kind. It is better to be safe than sorry.

Download from Www.Somanuals.com. All Manuals Search And Download.

6HWWLQJ#XS#\RXU#79

■ &RQQHFWLQJ#WKH#DHULDO#DQG#YLGHR#FDVVHWWH#UHFRUGHU#+9&5,

→

If you are connecting a VCR, follow A

diagram opposite.

D in the

Aerial

→

If you are not connecting a VCR, follow 1

Mains outlet

(AC 220 - 240 V,

50 Hz)

• For more details, see the manuals that came with the

equipment you want to connect.

• The connecting cables are not provided.

• You can watch a video using the VCR without doing C.

For details, see your VCR instruction manual.

• To connect more equipment, please see “Further

preparation” on page 30.

EXT-2

EXT-3

EXT-1

• If you connect a decoder to a T-V LINK compatible VCR,

set the DECODER (EXT-2) function to ON. For details, see

“Using the DECODER (EXT-2) function” on page 29.

Otherwise, you will not be able to watch scrambled

channels.

power

Cord

75-ohm

coaxial

cable

EXT-2

EXT-3

To use the T-V LINK functions, you must have a T-V LINK

compatible VCR connected by a SCART cable C to the EXT-

2 terminal on the TV. For details about T-V LINK functions,

see “T-V LINK functions” on page 7.

EXT-1

aerial

plug

21-pin SCART Cable

aerial plug

75-ohm coaxial

cable

VCR

To Aerial

Input

aerial plug

to aerial

output

AV IN/OUT

terminal

■ 3XWWLQJ#EDWWHULHV#LQWR#WKH#UHPRWH#FRQWURO

Use two AAA/R03 dry cell batteries.

Insert the batteries holding from the ó end, making sure the

ô and ó terminals are correctly lined up.

To open the battery compartment, slide the door downwards

and lift off. Replace the door by sliding it upwards until it

fastens into place.

• Follow the warnings printed on the batteries.

• Battery life is about six months to one year, depending on

how much you use the remote control.

• If the remote control does not work properly, fit new

batteries.

• The batteries we supply are only for setting up and

testing your TV. Please replace them as soon as you

need to.

• Always use good-quality batteries.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting up your TV

■ ,QLWLDO#VHWWLQJV

When the TV is first turned on, it goes into the initial setting

mode, and you will see the JVC logo. Follow the instructions

on the screen to make the initial settings.

Press the main power button on the TV

The power lamp lights red (for power on), then green (for

TV on) and the JVC logo is appears.

• If the power lamp stays red and does not change to

green:

your TV is in the standby mode. Press the

(standby) button on the remote control to turn your

TV on.

main power button

power lamp

• If the JVC logo does not appear this is because your

TV has already been turned on for the first time:

use the “LANGUAGE” and “AUTO PROGRAM”

functions to make the initial settings. For details, see

“INSTALL” on page 24.

2 ^{Press the}

button

The LANGUAGE menu appears.

3 ^{Press the ë buttons to choose}

ENGLISH

The on-screen display will then be in English.

RM-C55

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting up your TV

Note:

4 Press the

button to start the

AUTO PROGRAM function

• When your TV can detect the TV channel name from

the TV channel broadcast signal, it automatically

registers the TV channel name (ID) to the Pro-

gramme number (PR) in which the TV channel has

been registered.

The AUTO PROGRAM menu appears and the TV

channels you receive are automatically stored in the

programme numbers list (PR).

• If a TV channel you want to view is not set to a

programme number (PR), you can set it using the

MANUAL function. For details, see “EDIT/MANUAL”

on page 25.

• The AUTO PROGRAM function does not set the

programme number PR 0 (AV) for your video

cassette recorder. You will need to set this using the

MANUAL function.

• In some areas you may get TV reception from more

than one transmitter, for example different ITV

regions. In this case each TV channel could be set

twice. If this happens, the first set of channels will

have the stronger signal. If you want to delete the

second set of channels, you will have to do it

manually (see page 27).

To cancel the AUTO PROGRAM function:

Press the

button.

After the TV channels have been

registered in the programme numbers

list (PR), the EDIT menu appears

If you want to, you can now edit the programme numbers

(PR) using the EDIT/MANUAL function. For details, see

“EDIT/MANUAL” on page 25.

If you do not want to edit programme numbers (PR), go

to the next step.

6 Press the

button to display the

T-V LINK menu

Follow the T-V LINK menu according

to the type of VCR you have connected

to the EXT-2 terminal

If you do not have a T-V LINK compatible VCR

connected:

Press the

The T-V LINK menu disappears.

button to leave the T-V LINK menu.

If you have a T-V LINK compatible VCR

connected:

Follow the operating procedure “Downloading data to a

VCR” on page 29 to transmit the programme number

(PR) data.

Now, the initial settings are complete,

and you can watch the TV

Download from Www.Somanuals.com. All Manuals Search And Download.

709#/,1.#IXQFWLRQV

When you have a T-V LINK compatible VCR connected to the

EXT-2 Terminal on the TV, it is easier to set up the VCR and

to view videos. T-V LINK uses the following features:

■ 79#DXWR#SRZHU#RQ29&5#

LPDJH#YLHZ

When the VCR starts playing, the TV automatically turns on

and the images from the EXT-2 terminal appear on the

screen.

■ 3UH0VHW#GRZQORDG

The VCR will automatically download the registered data on

the TV channels from the TV. This means you do not need to

set up the program channels on your VCR manually.

The preset download function automatically begins when the

initial setting is complete or whenever you carry out the AUTO

PROGRAM or EDIT/MANUAL functions.

When the VCR menu is operated, the TV automatically turns

on and the images from the EXT-2 terminal appear on the

screen.

This function does not happen if your TV’s main power is

turned off. Set your TV’s main power to on (standby mode).

You can also carry out this function using your VCR controls.

Note:

When “FEATURE NOT AVAILABLE” is displayed:

• A “T-V LINK compatible VCR” means a JVC video

cassette recorder with the T-V LINK logo, or with one of

the following logos. However, these VCRs may support

some or all of the features described earlier. For details,

see your VCR instruction manual.

If “FEATURE NOT AVAILABLE” is displayed, the download

was not performed correctly. Before trying to download again,

check that:

• the VCR power is turned on

• the VCR is T-V LINK compatible

• the VCR is connected to the EXT-2 terminal

• the SCART cable is fully wired.

“Q-LINK” (a trademark of Panasonic Corporation)

“Data Logic” (a trademark of Metz Corporation)

“Easy Link” (a trademark of Phillips Corporation)

“Megalogic” (a trademark of Grundig Corporation)

“SMARTLINK” (a trademark of Sony Corporation).

■ 'LUHFW#5HF

“What You See Is What You Record”

You can easily record to VCR the images that you are

watching on the TV.

For details, read the manual for your VCR.

Use your VCR controls. “VCR IS RECORDING” is displayed.

In the following situations, the VCR will stop recording if

the TV is turned off, if the TV channel or input is changed,

or if the menu is displayed on the TV:

• when recording images from an external device connected

to the TV (for example a camcorder)

• when recording a TV channel after it has been unscrambled

on a decoder

• when recording a TV channel by using the TV’s output

because the VCR’s own tuner cannot properly receive that

channel

• You cannot carry out Direct Rec using your TV’s control.

• Generally, the VCR cannot record a TV channel that it

cannot receive properly on its own tuner, even if you can

view that TV channel on the TV. However, some VCRs

can record a TV channel by using the TV’s output if that

channel can be viewed on the TV. For details, see your

VCR instruction manual.

Download from Www.Somanuals.com. All Manuals Search And Download.

8VLQJ#\RXU#79²WKH#EDVLFV

■ 7XUQ#WKH#PDLQ#SRZHU#RQ

Press the main power button on the TV

The power lamp lights red and your TV is in the standby mode.

If the Power lamp lights green, the TV is already on.

To turn the main power off:

Press the main power button again.

The power lamp goes off.

To save energy, turn the main power off if you are not using

the TV for a long time.

main power button

power lamp

■ 7XUQ#WKH#79#RQ#IURP#VWDQGE\#PRGH

Press the

button, the

buttons

(standby) button, the

buttons or the number

The power lamp goes from red to green and your TV will be

turned on.

To turn the TV off:

number

buttons

Press the

(standby) button again.

The power lamp changes from green to red and the TV goes

into standby mode.

■ &KRRVH#D#79#FKDQQHO

Choose the programme number (PR) that the TV channel has

been set to.

Use the ë buttons:

Press the ë buttons to choose the programme number

(PR) you want.

Use the number buttons:

Enter the programme number (PR) of the channel using the

number buttons.

Example

→

• PR12

• PR6

press ~ and Ÿ.

→

press ¤.

Use the PR LIST:

1 Press the 9 (information) button to

RM-C55

display the PR LIST

;

Download from Www.Somanuals.com. All Manuals Search And Download.

Using your TV–the basics

Use the ë buttons:

Press the ë buttons to choose an EXT terminal

2 Press the

programme number (PR). Then press the

button.

and

buttons to choose a

Use the PR LIST:

• For Programme numbers (PR) where you have the CHILD

1 Press the

(information) button to

LOCK function set, the (CHILD LOCK) mark appears

next to the programme number (PR) in the PR LIST.

• You cannot use the ë buttons to choose a Programme

number (PR) which has the CHILD LOCK set.

display the PR LIST

2 Press the ì and ë buttons to choose

an EXT terminal. Then press the

• Even if you try to choose a programme number (PR) with

button

the CHILD LOCK set, the (CHILD LOCK) mark will

• The EXT terminals are listed after programme number PR

99.

appear, and you cannot watch the TV channel. To watch

the TV channel, see “CHILD LOCK” on page 22.

• You can choose two types of video input signal:

S-VIDEO (Y/C signal) and regular video (composite

signal). For details, see “K(S-VIDEO input)” on page 20.

■ &KDQJLQJ#WKH#YROXPH

• If you do not have a clear picture or no colour appears,

change the colour system manually. See “COLOUR

SYSTEM” on page 18.

• If you choose an EXT terminal with no input signal, the

EXT terminal number becomes fixed on the screen.

• This TV set can automatically change over the input

according to a special signal from an external device.

(The EXT-4 terminal does not support it.)

Press the

volume.

buttons to change the

The volume indicator appears, and the volume changes, as

you press the C buttons.

■ :DWFKLQJ#LPDJHV#IURP#

H[WHUQDO#HTXLSPHQW

To use the programme number PR 0 (AV):

Choose the EXT terminal that the external equipment has

been connected to.

When the TV and VCR are connected only by the aerial cable,

choosing the programme number PR 0 (AV) allows you to

view images from the VCR. Set the VCR RF channel to

programme number PR 0 (AV) manually. For details, see

“EDIT/MANUAL” on page 25.

Use the

button:

Press the

button to choose an EXT terminal.

Pressing the

button changes the choice as follows:

Pressing the

button changes the choice as follows:

TV mode

EXT modes

TV mode

PR 0

EXT modes

EXT-1

Programme

numbers

PR 1 to PR 99

EXT-1

EXT-4

EXT-2

EXT-3

EXT-2

EXT-3

Programme

numbers

PR 1 to PR 99

EXT-4

• The VCR sends its playback image along the aerial cable

as an RF (radio frequency) signal.

• Also see your VCR instruction manual.

To return to a TV channel:

^{Press the}4 ^{button, the ë buttons or the number}

buttons.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using your TV–the basics

■ 8VLQJ#WKH#EXWWRQV#RQ#WKH#79

1 ^{Press the P B buttons to turn the}

TV on from standby mode

Press the P

programme number (PR) or an EXT

terminal

buttons to choose a

(Behind the front cover)

Press the

(volume) button and the

buttons to change the volume

1 Press the D (volume) button

The volume level indicator appears

2 Press the C buttons while the volume

level indicator is on screen

Download from Www.Somanuals.com. All Manuals Search And Download.

5HPRWH#FRQWURO#EXWWRQV#DQG#IXQFWLRQV

1 0XWLQJ#EXWWRQ

You can turn the sound off instantly.

Press the

sound. Pressing the

restores the previous volume level

(muting) button to turn off the

(muting) button again

2 1XPEHU#EXWWRQV

You can choose a programme number (PR) by

entering the programme number

Example:

→

• PR12

• PR6

press ~ and Ÿ.

→

press ¤.

You can also press the

EXT terminal.

button repeatedly to choose an

3 =220#EXWWRQ

You can change the screen size by changing to the picture

aspect ratio. The normal aspect ratio is 4:3 (width:height).

Choose the ideal one from the following ZOOM modes.

AUTO(WSS):

When a WSS (Wide Screen Signalling) signal, which shows

the aspect ratio of the picture, is included in the broadcast

signal or the signal from an external device, the TV

automatically changes the ZOOM mode to 16:9 ZOOM mode

or FULL mode according to the WSS signal.

If a WSS signal is not included, the picture is displayed in

accordance with the ZOOM mode set with the 4:3 AUTO

ASPECT function.

• For details of the 4:3 AUTO ASPECT function, see “4:3

AUTO ASPECT” on page 18.

• When the AUTO(WSS) mode does not function correctly

due to poor WSS signal quality or when you want to

change the ZOOM mode, press the 5 button and

change to another ZOOM mode.

RM-C55

REGULAR:

Use to view a normal picture (4:3 aspect ratio) as this is its

original shape.

How to open the cover

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control buttons and functions

PANORAMIC:

This stretches the left and right sides of a normal picture (4:3

aspect ratio) to fill the screen, without making the picture

appear unnatural.

2 Press the

buttons to choose a ZOOM

button

mode. Then press the

The picture expands and the chosen ZOOM mode is

displayed in about 5 seconds.

• The ZOOM mode may be automatically changed

due to the control signal from an external device.

When you want to return to the previous ZOOM

mode, choose the ZOOM mode again.

• The top and bottom of the picture are slightly cut off.

$GMXVWLQJ#WKH#YLVLEOH#DUHD#RI#WKH#

14:9 ZOOM:

This zooms up the wide picture (14:9 aspect ratio) to the

upper and lower limits of the screen.

SLFWXUH

If subtitles or the top (or bottom) of the picture are cut off, you

can adjust the visible area of the picture manually.

1 Press the

button

The ZOOM menu appears.

2 Press the

button to display the ZOOM

16:9 ZOOM:

This zooms up the wide picture (16:9 aspect ratio) to the full

screen.

mode indicatior.

The indicator appears.

3 While it is displayed, press the

buttons

16:9 ZOOM SUBTITLE:

This zooms up the wide picture (16:9 aspect ratio) with

subtitles to the full screen.

to change the height of the picture.

• You cannot adjust the visible area in REGULAR or

FULL mode.

4 +<3(5#6281'#EXWWRQ

You can enjoy sounds with a wider ambience.

Press the

the HYPER SOUND function on or off

(HYPER SOUND) button to turn

FULL:

This uniformly stretches the left and right sides of a normal

picture (4:3 aspect ratio) to fill the wide TV screen.

• For 16:9 aspect ratio pictures that have been squeezed

into a normal picture (4:3 aspect ratio), use the FULL

mode to restore the picture to its original shape.

&KRRVH#WKH#=220#PRGH

• The HYPER SOUND function does not work properly with

mono sound.

1 Press the

button to display the ZOOM

• The HYPER SOUND function can be also turned on or off

by using the SOUND SETTING menu. For details, see

“HYPER SOUND” on page 19.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control buttons and functions

5#,QIRUPDWLRQ#EXWWRQ

9 &RORXU#EXWWRQV

You can display the PR LIST or the current time on the

screen.

The colour buttons are used for the teletext operations or the

menu operations. For details, see “~ Teletext control buttons

and VCR/(/DVD switch” on page 14 or “Using the TV’s

menus” on page 16.

Press the

Pressing the

(information) button

(information) button changes the

0 2.#EXWWRQ

display as follows:

The

button is used to operate menus. For details, see

“Using the TV’s menus” on page 16.

#%XWWRQV

You can choose a programme number (PR) or an EXT

terminal.

Press the

buttons to choose a

Programme number (PR) or an EXT terminal.

The

buttons will also operate menus.

For details, see “Using the TV’s menus” on page 16.

= 9&52'9'# FRQWURO# EXWWRQV# DQG

9&52(2'9'#VZLWFK

These buttons will operate a JVC brand VCR or DVD player.

Pressing a button that looks the same as the device’s original

remote control button has the same effect as the original

remote control.

Current time

No display

• You can choose programme numbers (PR) or EXT

terminals with the PR LIST. For details, see “Use the PR

LIST:” on page 8.

• This TV uses teletext data to set the time. If the TV has not

received a TV channel that has teletext programmes

since it was turned on, the time display is blank. To see

the time, choose a TV channel that has teletext

programmes. The time will still be displayed as long as

you do not turn off the TV, even if you choose other TV

channels.

1 Set the VCR/(/DVD switch to the VCR or

DVD position.

VCR:

When you are using a VCR, set the switch to the VCR

position.

• When watching videos, the incorrect time is sometimes

displayed.

DVD:

When you are using a DVD player, set the switch to the

DVD position.

• The

(information) button will also operate menus.

For details, see “Using the TV’s menus” on page 16.

(Text):

(

When you are viewing Teletext programmes, set the

switch to the (Text) position.

6 79#EXWWRQ

You can return to a TV channel instantly.

(

2 Press the VCR/DVD control button to

control your VCR or DVD player

Press the

button.

The TV returns to the TV mode and a TV channel appears.

• If your device is not made by JVC, these buttons will

• The

button will also operate menus. For details, see

not work.

“Using the TV’s menus” on page 16.

• Even if your device is made by JVC, some of these

buttons may not work, depending on the device you

are using.

7 ì#%XWWRQV

You can adjust the volume.

• You can use the

buttons to choose a TV channel

the VCR will receive, or choose the chapter the DVD

player plays back.

Press the ì buttons to adjust the sound.

• The ì buttons will also operate menus. For details, see

• Some models of DVD player use the

buttons for

“Using the TV’s menus” on page 16.

both operating the fast forward/backward functions

and for choosing the chapter. In this case, the 1/

¡ buttons do not work.

8 6WDQGE\#EXWWRQ

Press the

on or off.

(standby) button to turn the TV

When the TV is turned on, the power lamp changes from red

to green.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control buttons and functions

■ ~#7HOHWH[W#FRQWURO#EXWWRQV#DQG#9&52(2'9'#VZLWFK

4 Choose a teletext page by pressing the

buttons, number buttons or colour

buttons

To return to the TV mode:

Press the

button or

(Text) button.

• If you have trouble receiving teletext broadcasts,

contact your local dealer or the teletext station.

• In Text mode, the ZOOM mode is fixed to FULL.

• You cannot operate menus when viewing a teletext

programme.

8VLQJ#WKH#/LVW#0RGH

You can store the numbers of your favourite teletext pages in

memory and call them up quickly using the colour buttons.

To store the page numbers:

1 Press the

mode

button to go into the List

The page numbers you have stored are displayed at the

bottom of the screen.

2 Press a colour button to choose a

position. Then press the number buttons

to enter the page number

3 Press and hold down the

button

%DVLF#RSHUDWLRQ

You can view two types of teletext broadcasts on the TV:

FLOF (Fastext) and WST (World Standard Text).

The four page numbers blink white to show that they are

stored in memory.

To call up a stored page:

1 Choose a TV channel with a teletext

broadcast

1 Press the ù button to enter the List mode

2 Press a colour button having a stored page

2 Set the VCR/(/DVD switch to the

(Text)

(

position

To leave the List mode:

Press the ù button again.

3 Press the : (Text) button to display

the teletext

Pressing the : (Text) button changes the mode as

follows:

TV mode

Text mode

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control buttons and functions

+ROG

6L]H

You can hold a teletext page on the screen for as long as you

want, even while several other teletext pages are being

received.

You can double the height of the teletext display.

Press the ÷ button.

Press the û button

Hold indication

To cancel the Hold function:

Press the û button again.

6XE0SDJH

Some teletext pages include sub-pages that are automatically

displayed.

,QGH[

You can return to the index page instantly.

You can hold any sub-page, or view it at any time.

^{Press the}ú ^button

1 Press the õ button to operate the

sub-page function

FLOF (Fastext)/WST (World Standard Text):

Returns to page 100 or a previously specified page.

2 Press the Number buttons to enter a

sub-page number

List mode:

Returns to the page number displayed in the lower left area of

the screen.

Example:

• 3rd sub-page

→

press ), ), ) and 3.

&DQFHO

To cancel the sub-page function:

You can search for a teletext page while watching TV.

^{Press the}õ ^{button again.}

• You can also choose a sub-page by pressing the

red or green button.

1 Press the number button to enter a page

number, or press a colour button

5HYHDO

The TV searches for a teletext page.

Some teletext pages include hidden text (such as the

answers to a quiz).

2 ^{Press the}ü ^button.

You can display the hidden text.

The TV programme appears. When the TV finds the

teletext page, its page number appears in the upper left

of the screen.

Each time you press the ø button, text is

hidden or revealed

3 ^{Press the}ü ^{button to return to a teletext}

page when the page number is on the

screen

Note:

• The TV mode cannot be resumed by pressing the

button. To return to the TV mode press the

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

8VLQJ#WKH#79·V#PHQXV#

This TV has a number of functions you can operate using

menus. To use all your TV’s functions fully, you need to

understand how to use the basic menus.

1 ^{Press the}

button to display the

MENU (main menu)

The MENU (main menu) appears. In it, the titles of the

menus are displayed.

2 Press the

buttons to choose a

menu title, and press the

button

The menu appears.

3 Follow the menus according to the

function you want to use

• For more details, see the descriptions of each menu

and its functions, on the following pages.

• The display appearing at the bottom of a menu

shows you a button on the remote control that you

can use when you operate a chosen function.

4 Press the

button to complete the

setting

The menu disappears.

To return to the previous menu:

Press the

(information) button.

To exit a menu instantly:

^{Press the}4 ^button.

Download from Www.Somanuals.com. All Manuals Search And Download.

3LFWXUH#VHWWLQJ

• You can change the HUE setting (picture hue) only

when the colour system is NTSC 3.58 or NTSC 4.43.

(See “Specifications” on page 34.)

To return to the default settings in each TINT

mode:

Press the blue button.

This returns the picture settings in the TINT mode you

have chosen to the default settings, and stores them in

the TINT mode.

To display the PICTURE SETTING menu:

3 Press the

settings

button to complete the

1 Press the

button to display the MENU

(main menu)

The menu disappears.

2 Press the ë buttons to choose PICTURE

■ (&2#02'(

SETTING, and press the button

When you set the ECO MODE function to ON, the screen

contrast is automatically adjusted to a setting suitable for the

brightness of your room. This reduces eye strain for you and

the amount of power the TV uses.

■ 7,17

You can select one of three TINT modes (three kinds of

picture settings) to adjust the picture settings automatically.

1 Press the ë buttons to choose ECO

1 Press the ë buttons to choose TINT

MODE

2 Press the ì buttons to choose a mode

2 Press the ì buttons to choose ON

COOL:

To cancel the ECO MODE function:

A cool white colour base with a boost in the colour and

contrast levels that creates a more vivid picture.

Press the ì buttons to choose OFF.

3 Press the

setting

button to complete the

WARM:

A warm orange/red colour base that creates the

appropriate colour and contrast levels for watching films.

The menu disappears.

NORMAL:

A normal white colour base with normal colour and

contrast levels.

3 Press the

setting

button to complete the

The menu disappears.

■ 3LFWXUH#DGMXVWPHQW

You can change the picture settings of each TINT mode as

you like.

The picture settings changed are stored in the TINT mode.

1 Press the ë buttons to choose an item.

2 Press the ì buttons to change the

setting.

Item

Lower

Higher

CONTRAST

(picture contrast)

Darker

Softer

Brighter

Sharper

Deeper

BRIGHT

(picture brightness)

SHARP

(picture sharpness)

Lighter

Reddish

COLOUR

(picture colour)

Greenish

HUE

(picture hue)

Download from Www.Somanuals.com. All Manuals Search And Download.

3LFWXUH#IHDWXUHV

2 Press the ì buttons to choose the

appropriate colour system.

PAL:

PAL system

NTSC 3.58:

NTSC 3.58 MHz system

NTSC 4.43

NTSC 4.43 MHz system

AUTO:

To display the PICTURE FEATURES menu:

This function detects a colour system from the input

signal. You can only use this when you are viewing a

picture from programme number PR 0 (AV), or on EXT

terminal.

1 Press the

menu)

button to display MENU (main

2 Press the ë buttons to choose PICTURE

3 Press the

setting

button to complete the

FEATURES, and press the

button

The menu disappears.

■ $872#915

• The AUTO function may not work properly if you

have poor signal quality. If the picture is abnormal in

the AUTO function, choose another colour system

manually.

VNR Stands for “video noise reduction”.

The AUTO VNR function reduces any “noise” (interference or

snowing) in the current picture. The function also adjusts the

optimum sharpness of the picture (SHARP).

• You cannot choose NTSC 3.58 or NTSC 4.43 for

programme numbers PR 0 (AV) to PR 99.

1 Press the ë buttons to choose AUTO

VNR

■ 7=6#$872#$63(&7

2 Press the ì buttons to choose AUTO

This function only works when the ZOOM mode is set to

AUTO(WSS) mode. It sets the ZOOM mode you want to use

for when a WSS signal is not included in the broadcast signal

or the signal from an external device. You can choose one of

three ZOOM modes.

MIN:

The AUTO VNR function is cancelled. If you set the

mode to AUTO but feel that the sharpness of the original

picture has not been reproduced fully, change the mode

to MIN. However, any noise remaining in the original

picture may be emphasized.

• For details of the AUTO(WSS) mode, see the “AUTO

(WSS)” section within “3 ZOOM button” on page 11.

MAX:

This mode always reduces any noise as much as

possible, irrespective of state of the picture. When you

set the mode to AUTO but still notice some noise,

change the mode to MAX. However, this may reduce the

sharpness of the picture.

1 Press the

buttons to choose 4:3 AUTO

button

ASPECT. Then press the

The sub-menu of the 4:3 AUTO ASPECT function

appears.

3 Press the

setting.

button to complete the

The menu disappears.

■ &2/285#6<67(0

The colour system is chosen automatically. However, if the

picture is not clear or no colour appears, choose the colour

system manually.

2 Press the

mode

buttons to choose a ZOOM

1 Press the

buttons to choose COLOUR

button

3 Press the

setting

button to complete the

SYSTEM. Then press the

The sub-menu of the COLOUR SYSTEM function

appears.

The menu disappears.

Download from Www.Somanuals.com. All Manuals Search And Download.

6RXQG#VHWWLQJ

■ +<3(5#6281'

You can enjoy sounds with a wider ambience.

1 Press the ë buttons to choose HYPER

SOUND

2 Press the ì buttons to choose ON

To cancel the HYPER SOUND function:

Press the ì buttons to choose OFF.

To display the SOUND SETTING menu:

1 Press the

button to display the MENU

3 Press the

setting

button to complete the

(main menu)

2 Press the

buttons to choose SOUND

The menu disappears

SETTING. Then press the

button

• The HYPER SOUND function does not work properly

with mono sound.

■ 67(5(2#2#,‡,,

• You can turn the HYPER SOUND function on or off

with a single press. For details, see “4 HYPER

SOUND button” on page 12.

When you are viewing a bilingual broadcast programme, you

can choose the sound from Bilingual I (Sub I) or Bilingual II

(Sub II). If you have poor reception on a stereo broadcast, you

can change from stereo to mono sound so that you can hear

the broadcast more clearly and easily.

Press the

STEREO / I • II

buttons to choose

2 Press the

mode

buttons to choose a sound

E:Stereo sound

H :mono sound

ýF :Bilingual I (sub I)

ýG :Bilingual II (sub II)

3 Press the

setting

button to complete the

The menu disappears.

• The sound mode you can choose differs depending

on the TV programme.

• This function does not work in the EXT modes. And

this function does not appear in the SOUND

SETTING menu.

■ 6RXQG#DGMXVWPHQW

You can adjust the sound to your liking.

1 Press the ë buttons to choose an item

2 Press the ì buttons to adjust it

Item

BASS

Weaker

Left

Stronger

Right

TREBLE

BALANCE

3 Press the

setting

button to complete the

The menu disappears.

Download from Www.Somanuals.com. All Manuals Search And Download.

(;7#6(77,1*

3 Press the

setting.

button to complete the

The menu disappears.

• The EXT-1 terminal does not support S-VIDEO signal

(Y/C signal) and you cannot set K (S-VIDEO input)

in the EXT-1 terminal.

• Setting K (S-VIDEO input) changes the head

character from “E” to “S”. When an EXT terminal

receives a normal video signal, “E1”, “E2”, “E3” or

“E4” appears on the display. This changes to “S2”,

“S3” or “S4” when it receives an S-VIDEO signal.

To display the EXT SETTING menu:

•

Even a device which can output an S-VIDEO signal

(Y/C signal) may output a regular video signal

(composite signal) depending on the device setting. If

a picture cannot appear because the K (S-VIDEO

input) setting has been made, read the device

instruction manual carefully again to check for the

device settings.

1 Press the

button to display the MENU

(main menu)

2 Press the ë buttons to choose EXT

SETTING. Then press the button

■ K+609,'(2#LQSXW,

■ /,67

You can connect a device (such as an S-VHS VCR) to enjoy

the high-quality picture of the S-VIDEO signal (Y/C signal).

You can store a name for each of the devices connected to

each EXT terminal. Giving a name to an EXT terminal makes

the EXT terminal number appear on the screen, together with

its name.

Preparation:

• First read the device’s instruction manual and

“Further preparation” on page 30 to connect the device to

the TV properly. Second, follow the device’s instruction

manual to set the device so that it sends an S-VIDEO signal

(Y/C signal) to the TV.

1 Press the ë buttons or ì buttons to

choose an EXT terminal

• Do not set K(S-VIDEO input) to an EXT terminal

connected to a device which cannot output an S-VIDEO (Y/

C signal). If it is set wrongly, a picture cannot appear.

EXT-1

EXT-3

1 Press the

buttons or

buttons to

EXT-2

choose an EXT terminal

EXT-4

EXT-1

EXT-3

2 Press the blue button to display the name

list (LIST)

EXT-2

EXT-4

2 Press the yellow button and set the K

(S-VIDEO input)

An K (S-VIDEO input) mark is displayed. You can

view an S-VIDEO signal (Y/C signal) instead of the

regular video signal (composite signal).

To cancel the K (S-VIDEO input) setting:

Press the yellow button and turn off the K (S-VIDEO

input) mark.

The regular video signal (composite signal) pictures are

resumed.

Download from Www.Somanuals.com. All Manuals Search And Download.

EXT SETTING

button to complete the

3 Press the ë buttons to choose a name.

Then press the button.

3 Press the

setting.

The LIST disappears and the name is assigned to the

EXT terminal.

The menu disappears.

• During dubbing, you cannot turn off the TV. Turning

off the TV also turns off the output from the EXT-2

terminal.

To erase a name assigned to the EXT terminal:

Choose a blank space.

• When you choose an EXT terminal as an output, you

can view a TV programme or a picture from the other

EXT terminal while dubbing the picture from a

device connected to the EXT terminal onto a VCR

connected to the EXT-2 terminal.

4 Press the

setting.

button to complete the

The menu disappears.

• The RGB signals from TV games cannot be

output.Teletext programmes cannot be output.

• You cannot choose an EXT terminal name that is not

on the name list (LIST).

■ '8%%,1*

You can choose a signal source to be output from the EXT-2

terminal.

You can do this with the output signal of the device connected

to another EXT terminal, or the picture and sound from a TV

channel you are currently viewing.

1 Press the ì buttons to choose the EXT-2

terminal.

2 Press the ë buttons to choose another

EXT terminal or TV.

The arrow in the menu represents a signal flow. The left

side of the arrow shows a signal source output from the

EXT-2 terminal.

EXT-1/EXT-3/EXT-4:

The output signal of the device connected to an EXT

terminal passes through the TV and is output from the

EXT-2 terminal.

TV:

The picture and sound of the TV channel you are

currently viewing are output from the EXT-2 terminal.

Download from Www.Somanuals.com. All Manuals Search And Download.

)($785(6

■ %/8(#%$&.

You can set the TV to automatically change to a blue screen

and mute the sound if the signal is weak or absent, or when

there is no input from an external device.

1 Press the

BACK

buttons to choose BLUE

2 Press theì buttons to choose ON

To display the FEATURES menu:

To cancel the BLUE BACK function:

Press theì buttons to choose OFF.

1 Press the

button to display the MENU

(main menu)

3 Press the

setting

button to complete the

2 Press theë buttons to choose

FEATURES. Then press the

button

The menu disappears.

■ 6/((3#7,0(5

You can set the TV to automatically turn off after a set time.

■ &+,/'#/2&.

When there is a TV channel you do not want your children to

watch, you can use the CHILD LOCK function to lock out the

TV channel. Even when a child chooses a programme

number (PR) for a locked TV channel the screen will change

1 Press the

buttons to choose SLEEP

TIMER. Then press the

A sub-menu of the SLEEP TIMER function appears.

button

to blue and display (CHILD LOCK) so the TV channel

cannot be viewed. Unless you enter a pre-set ID number by a

special operation, the lock cannot be released and the child

cannot view the TV channel.

7R#VHW#WKH#&+,/'#/2&.#IXQFWLRQ

1 Press the ë buttons to choose CHILD

LOCK. Then press theA button.

“SET ID NO.” (ID number setting screen) appears.

2 Press the

time

buttons to set the period of

You can set the time for up to 120 minutes (2 hours) in

10 minute steps.

To cancel the SLEEP TIMER function:

Press the ï button to set the period of time to “OFF.”

2 To set the ID number you want

3 Press the

setting

button to complete the

1 Press theë buttons to choose a number

2 Press theì buttons to move the cursor

The menu disappears.

• One minute before the SLEEP TIMER function turns

off the TV, “GOOD NIGHT!” appears.

3 Press the

button.

• The SLEEP TIMER function cannot be used to turn

off the TV’s main power.

The sub-menu of CHILD LOCK appears.

• When the SLEEP TIMER function is on, you can

display the sub-menu of the SLEEP TIMER function

again to confirm or change the remaining period of

time of the SLEEP TIMER function. Press the

button to leave the menu after confirming or

changing the remaining time.

4 Press theë buttons to choose a TV

channel

Every time you press the ë buttons, the programme

number (PR) changes, and the picture of the TV channel

registered in the programme number (PR) is displayed

on the screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

5 Press the blue button and set the CHILD

LOCK function.

■ '(&2'(5#+(;705,

You can only use this function if you have a decoder

connected to a T-V LINK compatible VCR, which in turn is

connected to the EXT-2 terminal. To use this function, see

“Using the DECODER (EXT-2) function” on page 29.

(CHILD LOCK) appears and the TV channel is locked.

To reset the CHILD LOCK function:

Press the blue button again.

• If you have not connected a decoder with a T-V LINK

compatible VCR to the EXT-2 terminal, setting this function

to “ON” by mistake causes the picture/sound of a TV

channel you are currently viewing to disapper.

(CHILD LOCK) disappears.

6 Press the

setting.

button to complete the

The menu disappears.

• To disable easy resetting of the CHILD LOCK

function, the menu disappears if you choose the

CHILD LOCK function and press the

button.

7R#YLHZ#D#ORFNHG#79#FKDQQHO

1 Choose a programme number (PR) for a

locked TV channel, by using the number

buttons or PR LIST

The screen changes to blue and the (CHILD LOCK)

appears. You cannot view the TV channel.

2 Press the

(information) button to

display “ID NO.” (ID No. input screen)

3 Press the number buttons to enter the ID

number

The lock is temporarily released so you can view the TV

channel.

If you have forgotten the ID number:

Perform step 1 of “To set the CHILD LOCK function”.

After confirming the ID number, press the

exit the menu.

button to

• Even if you reset the lock temporarily, it does not

mean that the CHILD LOCK function set for the TV

channel is cancelled. The next time anyone tries to

view the TV channel, it will be locked again.

• When you want to cancel the CHILD LOCK function,

you must perform the operation “To set the CHILD

LOCK function” again.

• To stop it being easy to choose the programme

number (PR) of a locked TV channel, the

programme number (PR) has been set so that it

cannot be chosen by the

of the TV.

buttons or the buttons

• To stop it being easy to reset of the lock, “ID NO.” (ID

No. input screen) is set so that it cannot appear

unless you press the

(Information) button.

Download from Www.Somanuals.com. All Manuals Search And Download.

,167$//

To cancel the AUTO PROGRAM function:

Press the button.

3 After the TV channels have been stored in

the programme numbers (PR) list, the EDIT

menu appears

You can now edit the programme numbers (PR) list

using the EDIT/MANUAL function. For details, see

“EDIT/MANUAL” on page 25.

To display the INSTALL menu:

When not using the EDIT/MANUAL function:

If you do not need to use the EDIT/MANUAL function, go

to the next step.

1 Press the

button to display the MENU

(main menu)

2 Press the

buttons to choose the

4 Press the

button to display the T-V LINK

INSTALL menu. Then press the

button

■ /$1*8$*(

You can choose the language you want to use for the

on-screen display from the language list in the menu.

1 Press the

buttons to choose

LANGUAGE. Then press the

A sub-menu of the LANGUAGE function appears.

button

5 Operate the T-V LINK menu according to

the type of video cassette recorder (VCR)

you have connected to the EXT-2 terminal

If you do not have a T-V LINK compatible VCR

connected:

Press the

button to leave the T-V LINK menu.

The T-V LINK menu disappears, and all the settings are

completed.

2 Press the

language

buttons to choose a

If you have a T-V LINK compatible VCR

connected:

See “Downloading data to a VCR” on page 29 to

transmit the programme number (PR) data to the VCR.

3 Press the

setting

button to complete the

• When your TV can detect the TV channel name from

the TV channel broadcast signal, it automatically

registers the TV channel name (ID) to the Pro-

gramme number (PR) in which the TV channel has

been registered.

The menu disappears.

■ $872#352*5$0

You can automatically store the TV channels for which you

have the best reception. Store them in the TV’s programme

numbers (PR) list by doing the following.

• If a TV channel you want to view is not set to a

Programme number (PR), set it manually using the

MANUAL function. For details, see “EDIT/MANUAL”

on page 25.

1 Press the

PROGRAM

buttons to choose AUTO

• The AUTO PROGRAM function does not set the

programme number PR 0 (AV) for your video

cassette recorder. You will need to set this using the

manual function.

2 Press the

button to start the AUTO

PROGRAM function

The AUTO PROGRAM menu appears and the TV

channels you receive are automatically registered in the

programme numbers (PR) list.

• In some areas you may get TV reception from more

than one transmitter, for example. different ITV

regions. In this case each TV channel could be set

twice. If this happens, the first set of channels will

have the stronger signal. If you want to delete the

second set of channels, you will have to do it

manually (see page 27).

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALL

2 Follow the options for the function you

want to use

■ (',720$18$/

The EDIT/MANUAL functions are divided into two types:

• editing the current programme numbers (PR)

(EDIT functions); and

3 Press the

settings

button to complete the

• manually storing a TV channel you want to view a

programme number (PR) (MANUAL function).

The T-V LINK menu appears.

Here are the details about these functions:

MOVE:

This function changes the programme number (PR) of a TV

channel.

ID:

This function registers a channel name (ID) to a TV channel.

4 Follow the T-V LINK menu according to the

type of VCR you have connected to the

EXT-2 terminal

INSERT:

This function adds a new TV channel in the current

programme numbers (PR) list by using the CH/CC number.

If you do not have a T-V LINK compatible VCR

connected:

DELETE:

This function deletes a TV channel you do not want to list.

Press the

button to leave the T-V LINK menu.

The T-V LINK menu disappears and all the settings are

completed.

MANUAL:

This function manually stores a new TV channel in a

programme number (PR).

If you have a T-V LINK compatible VCR

connected:

Follow the operating procedure “Downloading data to a

VCR” on page 29 to transmit the programme number

(PR) data to the VCR.

• For programme number PR 0, “AV” appears in the

programme numbers (PR) list.

• An EXT terminal number does not appear in the

programme numbers (PR) list.

• The CH/CC number is a number unique to the TV and

corresponds to the channel number of a TV channel. For

the relationship between a channel number and a CH/CC

number, see “CH/CC NUMBER” on page 27.

• You cannot use the INSERT function if you do not know

the channel number of a TV channel. Use the MANUAL

function to register a TV channel in the programme

number (PR) list.

029(

1 Press the

channel

buttons to choose a TV

Every time you press the

buttons, the programme

number (PR) changes, and the picture of the TV channel

stored in the programme number (PR) appears on the

screen.

Caution:

2 Press the button to start the MOVE

• Using the MOVE, DELETE or INSERT functions rewrites the

current programme numbers (PR) list. Therefore, the

programme numbers (PR) of some of the TV channels will

change.

function

• Using the MANUAL function for a TV channel for which the

CHILD LOCK function has been set cancels the CHILD

LOCK function for that channel.

• Using the MANUAL function for a TV channel for which the

DECODER (EXT-2) function has been set to ON returns the

setting of the DECODER (EXT-2) function for that channel

to OFF.

• When a TV channel has already been registered in PR 99,

using the INSERT function deletes that TV channel.

3 Press the

buttons to choose a new

programme number (PR)

1 Press the

buttons to choose EDIT/

button

MANUAL. Then press the

To cancel the MOVE function:

Press the (information) button.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALL

• You can give your own unique channel name (ID) to

4 Press the button to change the

programme number (PR) of a TV channel

to a new programme number (PR)

the TV channel. When you have finished step 3, do

not go to step 4. Press the

buttons to move the

buttons to choose each

cursor, and press the

character of the channel name (ID). Then press the

button to register the channel name (ID) to the TV

channel.

1 Press the

channel

buttons to choose a TV

,16(57

Preparation:

Every time you press the

buttons, the programme

• You need to find the CH/CC number for the TV channel.

Find the CH/CC number from the “CH/CC NUMBER” table

on page 27 based on the channel number of the TV chan-

nel.

number (PR) changes, and the picture of the TV channel

stored in the programme number (PR) appears on the

screen.

2 Press the red button to start the ID

function

1 Press the

buttons to choose a

Programme number (PR) for which you will

2 Press the green button and start the

INSERT function

3 Press the

buttons to choose the first

character of a channel name (ID) you want

to give the TV channel

To cancel the INSERT function:

Press the

(Information) button.

3 Press the ë buttons to choose “CC” or

“CH” according to the CH/CC number of

the TV channel

To cancel the INSERT function:

Press the 9 (Information) button.

4 Press the blue button to display the ID LIST

(channel name list)

4 Press the Number button to enter the re-

maining CH/CC number

The TV shifts to registration mode.

When the registration is completed, the picture of the TV

channel appears on the screen.

• The CH/CC number is a number given to each

broadcast frequency that carries a TV channel. If the

TV cannot detect the TV channel corresponding to

the broadcast frequency indicated by the CH/CC

number, a “no-signal” picture appears.

5 Press the

buttons to choose the

channel name (ID)

To cancel the ID function:

Press the

(Information) button.

6 Press the

button to give a channel

name (ID) to a TV channel

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALL

'(/(7(

■ &+2&&#180%(5

• When you want to use the INSERT function on page 26,

find the CH/CC number corresponding to the channel

number of the TV channel from this table.

1 Press the ë buttons to choose a TV

channel

Every time you press the ë buttons, the programme

number (PR) changes over, and the picture of the TV

channel stored in the programme number list (PR)

appears on the screen.

If you want to know a particular TV channel’s channel

menu, look in TV listings magazines or contact the

broadcaster.

Channel

E40

E41

E42

E43

E44

E45

E46

E47

E48

E49

E50

E51

E52

E53

E54

E55

E56

E57

E58

E59

E60

E61

E62

E63

E64

E65

E66

E67

E68

E69

CH 02 / CH 202

CH 03 / CH 203

CH 04 / CH 204

CH 05 / CH 205

CH 06 / CH 206

CH 07 / CH 207

CH 08 / CH 208

CH 09 / CH 209

CH 10 / CH 210

CH 11 / CH 211

CH 12 / CH 212

CH 21 / CH 221

CH 22 / CH 222

CH 23 / CH 223

CH 24 / CH 224

CH 25 / CH 225

CH 26 / CH 226

CH 27 / CH 227

CH 28 / CH 228

CH 29 / CH 229

CH 30 / CH 230

CH 31 / CH 231

CH 32 / CH 232

CH 33 / CH 233

CH 34 / CH 234

CH 35 / CH 235

CH 36 / CH 236

CH 37 / CH 237

CH 38 / CH 238

CH 39 / CH 239

E2, IR A

CH 40 / CH 240

CH 41 / CH 241

CH 42 / CH 242

CH 43 / CH 243

CH 44 / CH 244

CH 45 / CH 245

CH 46 / CH 246

CH 47 / CH 247

CH 48 / CH 248

CH 49 / CH 249

CH 50 / CH 250

CH 51 / CH 251

CH 52 / CH 252

CH 53 / CH 253

CH 54 / CH 254

CH 55 / CH 255

CH 56 / CH 256

CH 57 / CH 257

CH 58 / CH 258

CH 59 / CH 259

CH 60 / CH 260

CH 61 / CH 261

CH 62 / CH 262

CH 63 / CH 263

CH 64 / CH 264

CH 65 / CH 265

CH 66 / CH 266

CH 67 / CH 267

CH 68 / CH 268

CH 69 / CH 269

2 Press the yellow button to delete the TV

channel

E3, IR B, ITALY A

E4, IR C, ITALY B

E5, IR D, ITALY D

The TV channel is deleted from the programme numbers

(PR) list.

E6, IR E, ITALY E

E7, IR F, ITALY F

E8, IR G

E9, ITALY G

E10, IR H, ITALY H

E11, IR J, ITALY H+1

E12, ITALY H+2

E21

E22

E23

E24

E25

E26

E27

E28

0$18$/

E29

E30

1 Press the

buttons to choose a

E31

E32

programme number (PR) for a new TV

channel

E33

E34

E35

E36

2 Press the blue button to activate the

MANUAL function

E37

E38

E39

Channel

S31

CC 01 / CC 201

CC 02 / CC 202

CC 03 / CC 203

CC 04 / CC 204

CC 05 / CC 205

CC 06 / CC 206

CC 07 / CC 207

CC 08 / CC 208

CC 09 / CC 209

CC 10 / CC 210

CC 11 / CC 211

CC 12 / CC 212

CC 13 / CC 213

CC 14 / CC 214

CC 15 / CC 215

CC 16 / CC 216

CC 17 / CC 217

CC 18 / CC 218

CC 19 / CC 219

CC 20 / CC 220

CC 21 / CC 221

CC 22 / CC 222

CC 23 / CC 223

CC 24 / CC 224

CC 25 / CC 225

CC 26 / CC 226

CC 27 / CC 227

CC 28 / CC 228

CC 29 / CC 229

CC 30 / CC 230

CC 31 / CC 231

CC 32 / CC 232

CC 33 / CC 233

CC 34 / CC 234

CC 35 / CC 235

CC 36 / CC 236

CC 37 / CC 237

CC 38 / CC 238

CC 39 / CC 239

CC 40 / CC 240

CC 41 / CC 241

CC 75 / CC 275

CC 76 / CC 276

CC 77 / CC 277

CC 78 / CC 278

CC 79 / CC 279

S32

S33

S34

S35

S36

S37

S38

S39

To cancel the MANUAL function:

S10

S11

S12

S13

S14

S15

S16

S17

S18

S19

S20

S21

S22

S23

S24

S25

S26

S27

S28

S29

S30

S40

Press the

(Information) button.

S41

3 Press the green or red button to search for

a TV channel

Z, ITALY C

Z+1

Z+2

Scanning stops when the TV finds a TV channel. Then

the TV channel is displayed.

4 Press the green or red button repeatedly

until the TV channel you want appears

If the TV channel reception is poor:

Press the blue or yellow button to fine-tune the TV

channel.

5 Press the

button and register the TV

channel to a programme number (PR)

The normal EDIT menu appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

'(02

The DEMO function automatically demonstrates some of the

TV functions.

To display the DEMO menu:

1 Press the

button to display the MENU

(main menu)

2 Press the ë buttons to choose DEMO.

Then press the button

1 Press the ë buttons to choose ON

2 Press the

setting

button to complete the

The DEMO function is set to ON, and the demonstration

will start.

To stop the demonstration:

Press one of the buttons on the remote control.

When the DEMO function is set to ON:

Each time the TV is turned on, the demonstration starts

automatically. If you do not want that to happen, cancel

the DEMO function:

1 Display the DEMO menu again

2 Press the ë buttons to choose OFF

3 Press the

function

button to cancel the DEMO

Download from Www.Somanuals.com. All Manuals Search And Download.

2WKHU#PHQXV

4 Press the

buttons to choose

■ 'RZQORDGLQJ#GDWD#WR#D#9&5

You can send to the latest programme numbers (PR) data to

a VCR with the T-V LINK function.

FEATURES. Then press the

button.

The FEATURES menu appears.

• You can only do this when a T-V LINK compatible VCR is

connected to the EXT-2 terminal.

• This only works when the T-V LINK menu is being

displayed.

5 Press the

buttons to choose

DECODER (EXT-2) . Then press the

buttons to choose ON

An unscrambled picture appears.

To cancel the DECODER (EXT-2) function:

Press the buttons to choose OFF.

1 Turn on the VCR

2 Press the

button

6 Press the

setting

button to complete the

The data transmission begins.

The T-V LINK menu appears.

The T-V LINK menu disappears once the data

transmission ends.

When the T-V LINK menu changes over to

another menu:

The TV has finished its menu. This new menu is

opperated from the VCR. See the VCR instruction

manual for what to do next.

7 Follow “Downloading data to a VCR” on

page 29 to transmit the programme

number (PR) data to the VCR

• If “FEATURE NOT AVAILABLE” appears at the T-V

LINK menu, check the following three items. Then

press the

button to retry data transmission.

− Has a T-V LINK compatible VCR been

8 If you have another TV channel you want to

unscramble using a decoder, repeat steps

2 to 7.

connected to the EXT-2 terminal?

− Has the VCR power been turned on?

− Does the SCART cable that connects the EXT-2

terminal to the T-V LINK compatible VCR have all

its proper connections?

• If the DECODER (EXT-2) function has been set to

“ON” but the TV channel cannot be unscrambled,

check the following:

■ 8VLQJ#WKH#'(&2'(5#+(;705,##

− Has the decoder been connected to the VCR

properly according to the VCR and decoder

instruction manuals?

IXQFWLRQ

− Has the decoder power been turned on?

If you have a decoder connected to a T-V LINK compatible

VCR, which in turn is connected to the EXT-2 terminal, use

the DECODER (EXT-2) function to unscramble the

scrambled TV channels.

−

Can the TV channel be unscrambled with a

decoder?

− Do you need to change the VCR settings in order

to connect the decoder? Confirm that the VCR is

set properly by rechecking the VCR Instruction

manual.

1 Turn on the decoder power

2 Display the scrambled TV channel on the

Even if the decoder is working, a scrambled picture

appears.

3 Press the

button to display the MENU

The MENU (main menu) appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

)XUWKHU#SUHSDUDWLRQ

■ &RQQHFWLQJ#H[WHUQDO#HTXLSPHQW

Connect the equipment to the TV, making the correct rear

panel and front panel connections.

Before connecting anything:

• Read the manuals that came with the equipment.

Depending on the equipment, the connection method

may be different from the diagram. Also, the equipment

settings may need to change depending on the

connection method.

• Turn off all the equipment including the TV.

• The “Specifications” on page 34 give the details of the

EXT terminals. If you are connecting equipment not listed

in the following connection diagram, see the table to

choose the best EXT terminal.

(Behind the door)

• Connecting cables are not supplied.

1 VCR (composite signal)

2 VCR (composite signal/S-VIDEO signal)

3 T-V LINK compatible VCR (composite signal/S-VIDEO

signal)

4 Decoder

5 DVD player (composite signal/S-VIDEO signal)

6 DVD player (composite signal/RGB signal)

7 TV game (composite signal/RGB signal)

8 TV game (composite signal/S-VIDEO signal)

9 Headphones

0 Camcorder (composite signal/S-VIDEO signal)

- SCART cable

= Audio cable

~ Video cable

! S-VIDEO cable

EXT-2

EXT-3

EXT-1

EXT-2

EXT-3

EXT-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Further preparation

(TXLSPHQW#ZKLFK#FDQ#RXWSXW#WKH#

609,'(2#VLJQDO#+<2&#VLJQDO,#VXFK#DV

DQ#609+6#9&5

Connect the equipment to an EXT terminal (but not the

EXT-1 terminal).

You can choose between an S-VIDEO signal (Y/C signal) and

a regular video signal (composite signal). For details of how

to operate the equipment, see “K(S-VIDEO input)” on

page 20.

709#/,1.#FRPSDWLEOH#9&5

Be sure to connect the T-V LINK compatible VCR to the

EXT-2 terminal. If not, the T-V LINK function will not work

properly.

• When connecting a T-V LINK compatible VCR to the

EXT-2 terminal, be sure to connect the decoder to the

VCR. If not, the T-V LINK function may not work properly.

After you have stored TV channels in the programme

numbers (PR) list, set the DECODER (EXT-2) function for

the programme number (PR) to ON to unscramble a

scrambled TV channel. For details, see “Using the

DECODER (EXT-2) function” on page 29.

&RQQHFWLQJ#KHDGSKRQHV

Connect the headphones with a stereo mini-jack (3.5mm

diameter) to the headphone jack at the TV front panel.

• When you connect the headphones, the TV speakers go

off.

9LGHR#RU#VRXQG#VLJQDO#RXWSXW#IURP

WKH#(;705#WHUPLQDO

You can change over the output of the video/sound signal

from the EXT-2 terminal. This is useful when you want to dub

the video/sound from another device onto the VCR connected

to the EXT-2 terminal. For details on how to do this, see

“DUBBING” on page 21.

79#RXWSXW#IURP#WKH#(;704#WHUPLQDO

The video/sound signal of a TV channel you are viewing is

always output from the EXT-1 terminal.

• Changing over a programme number (PR) also changes

over the TV output from the EXT-1 terminal.

• The video/sound signal from an EXT terminal cannot be

output.

• Teletext programmes cannot be output.

Download from Www.Somanuals.com. All Manuals Search And Download.

79#EXWWRQV#DQG#SDUWV

■ )URQW#SDQHO

Push to open

(Behind the cover)

1 Remote control sensor and ECO sensor

⁵^P∨^/∧ ^{buttons /}^C^buttons

6 Power lamp

page 10

pages 5 and 8

2 Headphone jack (mini jack)

3 EXT-4 terminal

page 30

pages 20 and 30

page 10

7 Main power button

4 D (Volume) button

• Do not hold the TV by the front panel cover when moving the TV set. If you do, you may break the cover.

■ 5HDU#3DQHO

EXT-2

EXT-3

EXT-2

EXT-3

EXT-1

8 Aerial socket

page 4

0 EXT-2 terminal

- EXT-3 terminal

pages 4, 7, 20 and 30

pages 20 and 30

9 EXT-1 terminal

pages 4, 20 and 30

Download from Www.Somanuals.com. All Manuals Search And Download.

7URXEOHVKRRWLQJ

If a problem arises while you are using the TV, please read this troubleshooting guide carefully before you ask to have the TV

repaired. You may be able to fix it easily by yourself. For example, if the mains plug is disconnected from the mains outlet, or the

TV aerial has problems, you may think there is a problem with the TV itself.

Important:

• This troubleshooting guide only covers problems whose causes are not easy to decide. If you have a question when you are

operating a function, read the page(s) for that function carefully, not this troubleshooting guide.

• If you follow the advice in this troubleshooting guide without any success, unplug the mains plug and ask for your TV to be

repaired. Do not attempt to repair the TV by yourself or to remove the rear cover of the TV.

,I#\RX#FDQQRW#WXUQ#RQ#WKH#79

3RRU#VRXQG

• Is the mains plug connected to the mains outlet?

• Is the power lamp lit? If not, press the main power button.

• Have you adjusted BASS or TREBLE properly? If not, follow

the description “Sound adjustment” on page 19.

• When TV channel reception is poor, it can be hard to hear

stereo or bilingual sound. In this case, follow the

description “STEREO / I•II” on page 19 to hear the sound

1R#SLFWXUH#RU#QR#VRXQG

• Have you chosen a TV channel with very poor reception? If

so, the BLUE BACK function will be activated: the entire

screen becomes blue, and the sound is muted. If you still

want to view the TV channel, follow the description “BLUE

BACK” on page 22 to try to change the BLUE BACK function

setting to OFF.

more easily by changing it to a mono sound.

,I#WKH#79#GRHV#QRW#UHVSRQG#WR#WKH#

UHPRWH#FRQWURO

• Have the batteries of the remote control worn out? Follow

the description “Putting batteries into the remote control” on

page 4 and replace them with new batteries.

• Have you connected headphones to the TV?

Connecting headphones to the TV turns off the TV speakers.

• Have you attempted to use the remote control from the sides

or rear of the TV or from more than seven metres away from

the TV ? Use the remote control in the front of your TV or

from less than seven metres away.

3RRU#SLFWXUH

• If noise (snow) totally block out the picture, there may be a

problem with the aerial or aerial cable. Check the following

to try to solve the problem:

• When you are viewing a teletext programme, you cannot

− Have the TV and aerial been connected properly?

− Has the aerial cable been damaged?

− Is the aerial pointing in the right direction?

− Is the aerial itself faulty?

operate the menus. Press the

ordinary TV programme, and then try operating the menus.

button to return to the

• If the TV will not respond suddenly, press the main power

button on the TV and turn off the main power. Press the

main power button again to turn on the TV. If the TV returns

to a normal state, it is not a failure.

• If the TV or aerial suffers interference from other equipment,

stripes or noise may appear in the picture. Move any

equipment sach as an amplifier, personal computer, or a

hair drier, that can cause interference away from your TV.

Or try moving the TV. If the aerial suffers interference from

a radio tower or high-voltage wire, please contact your local

dealer.

2WKHU#LVVXHV

• When the SLEEP TIMER function operates, the TV is

automatically turned off. If the TV is turned off suddenly, try

to press the

(standby) button to turn on the TV once

again. If the TV goes back to normal, there is no problem.

• If the TV suffers interference from signals reflecting from

mountains or buildings, double-pictures (ghosting) will

occur. Try to change the aerial’s direction or replace it with

one with better directionality.

• When a WSS signal is included in the broadcast signal or

the signal from an external device, or when the TV is

receiving a control signal from an external device, the

ZOOM mode will change automatically. When you want to

return to the previous ZOOM mode, press the 5 button to

choose the ZOOM mode again.

• Are your COLOUR SYSTEM settings correct? Follow the

description “COLOUR SYSTEM” on page 18 to try to solve

the trouble.

• If you bring a magnetised device such as a speaker near to

your TV, the picture may be warped or unnatural colors now

appear at the corners of the screen. In this case, keep the

device away from your TV. If speakers cause this to happen,

use magnetic-shielded speakers instead.

• Have the COLOUR and BRIGHT settings been adjusted

properly? Follow the description “Picture adjustment” on

page 17 to try to adjust them properly.

• Videotaping teletext is not recommended because it may

not record correctly.

• The TV may make a crackling sound due to a sudden

change in temperature. The picture or sound may be nomal.

If you hear crackling sounds frequently while you are

viewing the TV, there may be other causes. As a precaution,

ask your service technician to inspect it.

• When a white and bright still image (such as a white dress)

is displayed on the screen, the white part may look as if it is

coloured. This is unavoidable due to the nature of the picture

tube itself, and not due to a TV failure. When the picture

disappears from the screen, the unnatural colours will also

disappear.

• Touching the screen may cause you to feel a slight electric

shock due to its static electricity. This is unavoidable due to

the construction of the picture tube. It is not a problem with

the TV. You can rest assured that this static discharge is not

harmful.

Download from Www.Somanuals.com. All Manuals Search And Download.

6SHFLILFDWLRQV

Model

AV28WT5EI*

AV24WT5EI*

Item

Broadcasting systems

Colour systems

CCIR I

PAL

•

The EXT terminals also support the NTSC 3.58/4.43 MHz system.

Channels and frequencies

Sound-multiplex systems

Teletext systems

IR A-J, E2-E12, E21-E69, S1-S41, X, Y, Z, Z+1, Z+2, ITALY A-H, ITALY H+1, ITALY H+2

NICAM (I) system

FLOF (Fastext), WST (World Standard Text)

220 - 240 V AC, 50 Hz

Power requirements

Power consumption

Maximum: 156 W, Average: 122 W,

Standby: 0.8 W

Maximum: 127 W, Average: 92 W,

Standby: 0.8 W

Picture tube size

Audio output

Speakers

Viewable area 66 cm (measured diagonally)

Rated Power output: 5 W + 5 W

(10 cm × 3 cm) oval × 2

Viewable area 56 cm (measured diagonally)

EXT-1 terminal

Euroconnector (21-pin, SCART)

•

Video input, Audio L/R inputs and RGB inputs are available.

TV broadcast outputs (Video and Audio L/R) are available.

EXT-2 terminal

Euroconnector (21-pin, SCART)

•

Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

Video and Audio L/R outputs are available.

T-V LINK functions are available.

EXT-3 terminal

EXT-4 terminal

Euroconnector (21-pin, SCART)

Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

•

RCA connectors × 3

S-VIDEO connector × 1

• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

Headphone jack

Dimensions (W × H × D)

Weight

Stereo mini-jack (3.5 mm in diameter)

716 mm × 489 mm × 496 mm

645 mm × 427 mm × 443 mm

34.2 kg

23.1 kg

Accessories

Remote control unit RM-C55 × 1

AAA/R03 dry cell battery × 2

* A basic model number. The actual model number may have characters added (such as “S” for silver) showing the

colour of the TV set.

We may change the design and specifications without notice.

Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any commercial or demonstration

purpose in public places (cafes, hotels, etc.) without the consent of the owners of copyright of the original picture sources, as

this would be an infringement of copyright.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Download from Www.Somanuals.com. All Manuals Search And Download.

Ingersoll Rand Septic System 670036 15X User Manual
Intel Computer Hardware 4112 User Manual
Jasco Universal Remote RM24973 User Manual
John Deere Lawn Mower GM1060 User Manual
John Lewis Freezer JLFZW1810 User Manual
JVC Car Stereo System GET0114 001A User Manual
JVC Portable CD Player RC EZ38SJ User Manual
Kenmore Oven 7904807 User Manual
Kenwood Meat Grinder MG510 User Manual
Klipsch Portable Speaker Icon Series User Manual