MINIDISC RECORDER
XM-EX90
POWER
1
6
2
7
3
4
5
8
9
10
FM MODE
TUNER
AUX
/
MUTING
+10
SLEEP
CLOCK
/
TIMER
UP
SET
CANCEL
DOWN
XM-EX90 MINIDISC RECORDER
CD CONTROL
/CANCEL
PLAY MODE REPEAT
CD
1
CD
2
CD
3
INPUT
DISC LOADING MECHANISM
MD CONTROL
TRACK
PLAY MODE REPEAT
DISPLAY
RECPAUSE
CD REC
MARKING
TAPE CONTROL
SAMPLING RATE CONVERTER
STANDBY
REC LEVEL
BASS
TREBLE
BALANCE
–
/
L
+
/
R
POWER
FADE
MUTING
S.A.BASS
VOLUME
RM-SEEX90MU REMOTE CONTROL
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0097-001A
[J]
Download from Www.Somanuals.com. All Manuals Search And Download.
Welcome !
We would like to thank you for purchasing one of our JVC products. Before connecting this unit to
the wall outlet, please read the instructions carefully to ensure that you obtain the best possible
performance. If you have any questions, please consult your JVC dealer.
Important cautions
Installation of the Unit
•
Select a place which is level, dry and neither too hot nor too cold (Between 5˚C and 35˚C or 41˚F-
95˚F).
•
•
•
•
•
Leave sufficient distance between the Unit and a TV.
Be sure to place the Unit in a location with good ventilation.
Do not use the Unit in a place subject to vibrations.
Do not place the Unit on a carpet.
Do not place the Unit on top of another heat-generating piece of equipment.
Power cord
•
•
Do not handle the power cord with wet hands!
When unplugging the Unit from the wall outlet, always pull the plug, not the power cord.
Malfunctions, etc.
•
There are no user serviceable parts inside. If anything goes wrong, turn off the power
immediately. If the same problem reoccurs when the power is turned on once more, turn off the
power again, unplug the power cord and consult your dealer.
•
Do not insert any metallic object into the Unit.
For safe use, observe the following
Avoid moisture, water and dust
Do not set your machine in moist or dusty places.
Avoid high temperatures
Do not expose your machine to direct sunlight or set near a heating device.
Do not block the vents
Poor-ventilation may damage your machine. So do not block the vents or put the unit in a poorly
ventilated place.
When you’re away
When away on travel or otherwise for an extended period of time, turn off the power and pull the
plug from the electrical socket.
Do not insert foreign matter into the machine
Do not insert wires, hairpins, coins, etc. into your machine.
Care of the cabinet
When cleaning your machine, use a soft cloth and follow the relevant instructions on the use of
chemically-coated cloths. Avoid applying benzene, thinner or other organic solvents and
disinfectants. This may cause deformation or discoloring.
If water gets inside the machine
Turn off the power and pull the plug from the electrical socket, then call the store where you made
your purchase. Using the machine in this state may cause a fire or electrical shock.
US and foreign patents licensed from Dolby Laboratories Licensing Corporation.
3
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Welcome ! .......................................................... 3
Important cautions.............................................. 3
For safe use, observe the following................... 3
COMPU LINK .................................................... 48
Rule on Digital Copying ................................. 50
SCMS (Serial Copy Management System) ...... 50
Parts Index ......................................................... 5
Front Panel.......................................................... 5
Display ................................................................ 6
Rear Panel........................................................... 7
Remote control unit ............................................ 8
About MD (Mini DIsc) .................................... 51
Role of the cartridge ......................................... 51
Two disc types .................................................. 51
ATRAC (Adaptive TRansform Acoustic Coding) 52
Sound skip guard memory ............................... 52
UTOC (User Table Of Contents) ....................... 52
Setting Up the System .................................... 10
Supplied Accesories ......................................... 10
Connection........................................................ 11
Remote control batteries.................................. 12
Remote control operation................................. 13
MD Error Messages........................................ 53
MD Restrictions .............................................. 54
Handling MDs .................................................. 55
Playback ........................................................... 14
MD playback (Basic operation) ......................... 14
Switching the displayed information ................ 16
Repeat playback................................................ 17
Program playback ............................................. 18
Random playback.............................................. 20
Additional Information ................................... 56
Troubleshooting ................................................ 56
Specifications.................................................... 57
Recording ......................................................... 21
MD recording (Basic operation)........................ 21
CD recording ..................................................... 24
Radio or tape recording .................................... 25
Editing Functions ............................................ 26
MD editing functions ........................................ 26
Dividing a track (DIVIDE) .................................. 28
Joining tracks (JOIN) ........................................ 30
Moving a track (MOVE) .................................... 32
Erasing a track (ERASE).................................... 34
Erasing all tracks in an MD (ALL ERASE) ......... 36
Assigning titles to an MD and its tracks .......... 38
Assigning titles while playback
or recording .................................................. 41
Remote Control of the othr Components..... 43
Remote control of the other optional
components from the provided remote control
unit .................................................................... 43
Remote controlling the amplifier/tuner ............ 44
Remote controlling the CD player and
cassette deck.................................................... 46
4
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Index
Front panel
10
11
12
9
8
XM-EX90 MINIDISC RECORDER
/CANCEL
INPUT
DISC LOADING MECHANISM
REC PAUSE
CD REC
7
6
SAMPLING RATE CONVETER
STANDBY
REC LEVEL
POWER
2
3
4
1
5
1 POWER button
8 0 button
Press to switch the power between ON and
STANDBY.
STANDBY indicator
The indicator is off while the power is ON
and lights up when the power is in STANDBY
mode.
Press to eject the MD.
9 INPUT button
Press to switch the recording input between
the digital and analog inputs. This button
should be pressed after pressing REC
PAUSE.
2 Display
p ‹/8 button
Press to start MD playback or recording, or to
let it pause temporarily.
3 MD insertion slot
Load an MD through this slot.
q &/CANCEL
4 Remote control sensor
Press to stop MD playback or recording, or to
clear a track in the program.
5 4, ¢, REC LEVEL buttons
Press to skip to the beginning of a desired
track, to fast forward or fast reverse a disc,
or adjust the recording level.
w Disc indicator
Lights in green when the power is switched
ON.
Lights in green during playback, and in red
during recording.
6 REC PAUSE
Press to enter record-pause mode.
7 CD REC
Press for synchronized recording with the
CD player.
5
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Display
7
DIGITAL12
REPEAT
ALL 1
1 2 3 4 5
6 7 8 9 10
11 12 13 14 15
L
R
REC
LEVEL
PROGRAM
RANDOM
2
6
1
3
4
5
1 Play indicators
5 Play mode indicators
‹: Lights up during MD playback or
PROGRAM: Lights in the program play
recording.
mode.
*: Lights up during pause.
RANDOM: Lights in the random play mode.
2 Recording status indicators
6 Track indicators
REC: Lights in record and record-pause
modes.
LEVEL, L, R: Lights during the analog input
level control operation.
Shows the number of tracks in the MD.
7 Input mode indicators
Shows the recording input mode.
“DIGITAL 1” or “DIGITAL 2” lights when the
respective digital input is used, and no
indicator is lit when the analog input is used.
3 Character display
Shows the track information, title, MD editing
function, recording-editing function, etc.
4 Repeat indicators
Shows the repeat mode.
REPEAT ALL: Lights when all tracks in an
MD or all tracks in the program are
played repeatedly.
REPEAT 1: Lights when a single track is
played repeatedly.
6
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear panel
RIGHT
LEFT
DIGITAL IN
–
–
1
OPTICAL
2
IN
(REC)
ANALOG
1
OUT
(PLAY)
COMPU LINK - 3
(SYNCHRO)
AC POWER CORD
2
3
4
1 ANALOG input/output jacks
4 AC POWER CORD receptacle
Connect to the MD output/input jacks of the
amplifier/tuner using the provided audio pin
cords.
Connect the provided AC power cord.
Connect the IN (REC) jacks with the
amplifier/tuner’s OUT (REC) jacks, and the
OUT (PLAY) jacks with its IN (PLAY) jacks.
2 COMPU LINK-3 (SYNCHRO) jacks
Connect each jack with the provided COMPU
LINK-3 (SYNCHRO) jack of another
component.
Either jack can be used for the connection.
3 DIGITAL IN jacks
Connect using the provided optical digital
cable.
1: Connect with the DIGITAL OUT jack of the
CD player.
2: Connect with the DIGITAL OUT jack of
your DBS tuner, etc.
7
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control unit
Normal control button panel
POWER
1
2
2
7
3
8
4
5
1
6
Open the normal control button panel as shown
below to access the editing control button panel.
9
10
FM MODE
/ MUTING
TUNER
AUX
+10
SLEEP
CLOCK
TIMER
/
UP
SET
CANCEL
DOWN
CD CONTROL
PLAY MODE REPEAT
CD
1
CD
2
CD
3
MD CONTROL
TRACK
PLAY MODE REPEAT
DISPLAY
MARKING
3
TAPE CONTROL
BASS
TREBLE BALANCE
– / L
+ / R
FADE
MUTING
S.A.BASS
VOLUME
RM-SEEX90MU REMOTE CONTROL
Editing control button panel
TITLE
SET
EDIT
ENTER
CANCEL
SMALL
LETTER
SPACE
This button does
not function.
5
4
8
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
1 POWER button
4 MD editing control buttons
EDIT: Switches the editing functions.
TITLE: Assigns a title to a MD or its track.
ENTER: Enters the editing contents in
memory.
Press to switch the power mode between
ON and STANDBY.
2 Numeric keys
Press to select a desired track number
directly.
Press MD CONTROL £ before pressing this
button.
To select track No. 5: Press 5.
To select track No. 15:Press +10 then 5.
To select track No. 20:Press +10 then 10.
To select track No. 32:Press +10 three times
then press 2.
SET: Sets the point where a track is divided
or the track to be edited.
£: Starts playback.
CANCEL: Cancels an editing item or
character.
</4, ¢/>: Selects a track number or
adjust track marking. These keys can be
used during editing.
SMALL LETTER: Switches the case of input
characters.
3 MD CONTROL buttons
The characters are uppercase while the
button is not lit, and lowercase when it is
lit in green.
Used to control the MD recorder.
£: Starts playback. Also sets the numeric
keys on the remote control unit to the MD
mode.
7: Stops playback or recording.
4, ¢: Skips to the beginning of a track.
¶: Initiates record-pause mode.
PLAY MODE: Switches the play modes,
which include the program play mode and
random play mode.
5 Character input keyboard
Used for direct input of characters.
REPEAT: Switches the repeat play modes,
which include the all-track repeat mode
and 1-track repeat mode.
DISPLAY: Switches the information shown
on the character display.
TRACK MARKING: Switches the track
assignment during recording between
automatic and manual.
* The buttons without description are for
use in controlling other optional
components (see page 43).
9
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the System
Supplied Accesories
Power cord x 1
Audio pin cords x 2
Optical digital cable x 1
Remote control unit x 1
Compu Link cable x 1
Batteries (R03 (UM-4)/AAA (24F)) x 2
Cautions for Placement
Do not place in any of the following ares.
•
•
•
•
•
•
•
•
Near a heater or other heat emmitting appliance.
In direct sunlight.
Do not place the CD player on top of the amplifer/tuner.
In a place warmer than 35°C (95F°).
In a bathroom, kitchen or other area with steam, humidity, or hot water.
In a place with lots of static electricity or dust.
In an unstable area.
Near appliances that receive electronic wave broadcasts, such as a television or tuner.
10
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
Amplifier/Tuner
INTEGRATED AMPLIFIER TUNER
/
VOLUME
BAND
INPUT
S. A. BASS
DIRECT
PHONES
DOWN
UP
STANDBY
POWER
KEY
MODE
Audio pin cords
Connect to the MD jacks of the amplifier/tuner.
Always connect the jacks with the plugs of the same colors so as
not to mistake the L (Left) and R (Right) connections.
Connect the OUT (PLAY) jacks to the IN (PLAY) jacks of the amplifier/
tuner, and the IN (REC) jacks to its OUT (REC) jacks.
CD player
COMPACT DISC PLAYER
/CANCEL
CD
CD
CD
3
2
1
PLAY & EXCHANGE
STANDBY
REPEAT PLAY MODE
POWER
Optical digital cable
Connect to the DIGITAL OUT jack of the CD player.
When making connections to the equipped with Compu
Link remote control system.CD player connect to the
DIGITAL IN 1 jack of this unit.
RIGHT
LEFT
DIGITAL IN
–
–
1
OPTICAL
2
IN
(REC)
ANALOG
OUT
(PLAY)
COMPU LINK - 3
(SYNCHRO)
AC POWER CORD
Optical digital cable
Connect to the DIGITAL OUT
jack of your DBS tuner, etc.
Be sure to remove the protective cap
before using the DIGITAL IN jack. Keep
the cap in a safe place so you can
replace it when not using the DIGITAL
IN jack.
Compu Link cable
Connect to the COMPU LINK-3 (SYNCHRO) jack of another equipped with Compu Link
remote control system.
11
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control batteries
Load the supplied batteries (2) into the remote control.
1 Open the battery case.
Push down and pull the lid in the direction of the arrow.
2 Load the batteries.
Insert two R03 (UM-4)/AAA(24F) batteries.
Match the polarity (+ and –) of the batteries with the +
and – marks inside the battery compartment.
3 Close the battery case.
Operating the Remote Control
Point the remote control toward the remote sensor on the front panel. The signal may not reach the
remote sensor if the remote control is used at an angle of 60°, or if there are objects between the
remote control and the remote sensor.
XM-EX90 MINIDISC RECORDER
/CANCEL
Cautions
INPUT
DISC LOADING MECHANISM
REC PAUSE
CD REC
Observe the following to avoid battery leakage or explosion:
SAMPLING RATE CONVERTER
STANDBY
POWER
REC LEVEL
•
If the range or effectiveness of the remote control
decreases, replace the batteries using R03 (UM-4)/
AAA(24F) type dry cells.
•
•
•
Do not use an old battery together with a new one.
Do not use different types of batteries together.
Do not disassemble the batteries or subject them to
high temperatures, like an open fire.
•
Remove the batteries if the remote control will not be
used for a long time.
12
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control operation
The remote control unit has a two-panel configuration, and opening the normal control button panel
allows you to access the editing control button panel. Use the normal control buttons for playback
and recording operations, and use the editing control buttons for editing and title input operations.
1
2
3
Normal control
button panel
Editing control button panel
Point the transmitter of the remote control unit toward the remote control sensor on the main unit
before pressing a button. If the remote control unit is used from an oblique direction or if there is an
obstacle between it and the main unit, the remote control signals may not reach the main unit.
When using the normal control buttons
When using the editing control buttons
XM-EX90 MINIDISC RECORDER
XM-EX90 MINIDISC RECORDER
/CANCEL
/CANCEL
INPUT
INPUT
DISC LOADING MECHANISM
DISC LOADING MECHANISM
REC PAUSE
CD REC
REC PAUSE
CD REC
SAMPLING RATE CONVERTER
SAMPLING RATE CONVERTER
STANDBY
POWER
REC LEVEL
STANDBY
POWER
REC LEVEL
13
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
MD playback (Basic operation)
The basic operation for playing an MD is described below.
If you use the remote control unit, use the MD CONTROL buttons on the normal control button panel.
1 Load an MD (Mini Disc).
Hold an MD with the side on which an arrow is marked
facing up, and insert it into the slot in the direction of the
arrow. The MD will be pulled in automatically from the
middle.
Number of tracks
Total playing time
• If the MD has a disc title, the display shows the disc
title then the number of tracks and total playing time
of the disc.
Shortcut:
When the power is in the STANDBY mode, inserting
an MD turns the power on and the MD is pulled in
automatically.
2 Press ‹/8.
Playback starts.
/CANCEL
The ‹ indicator lights up.
• If you are using the remote control unit, press £.
Shortcut:
Main unit
Remote control unit
When the power is in the STANDBY mode, pressing
‹/8 or £ on the remote control unit turns the power
on and starts MD playback automatically. In this case,
the display will show “NO DISC” if no MD has been
loaded.
• Press &/CANCEL to stop playback in the middle. If you
are operating the remote control unit, press 7.
/CANCEL
Main unit
Remote control unit
• Press 0 to eject the MD.
INPUT
14
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
To let playback pause temporarily:
Press ‹/8. The * indicator lights up.
Pressing the button again resumes playback from the
position where it has paused.
/CANCEL
Lights.
Main unit
To skip to the beginning of a track:
REC LEVEL
Press ¢ once to skip to the beginning of the next
track.
Press 4 once to skip to the beginning of the current
track being played.
• Each press skips an additional track.
Main unit
Remote control unit
Fast forward/fast reverse
REC LEVEL
These operations are possible while the MD recorder is
in play or pause mode.
Press and hold ¢ to fast forward.
Press and hold 4 to fast reverse.
• These operations cannot be controlled from the
remote control unit.
REC LEVEL
To select and play a desired track
Main unit/remote control unit:
1. Press 4 or ¢ to select a track number.
2. Press £ to start playback.
Remote control unit:
Main unit
Remote control unit
Press £ then immediately compose the track number
of the desired track.
3
2
7
4
9
1
6
5
To select track No. 5: Press 5.
To select track No. 15: Press +10 then 5.
To select track No. 20: Press +10 then 10.
To select track No. 52: Press +10 five times then press
2.
8
10
+
10
Caution
Do not mistake the MD insertion direction, otherwise malfunction will result.
15
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching the displayed information
The display can show the disc title, track title and remaining time (recording time available when a
recordable MD is loaded) information.
The displayed information can be switched using DISPLAY of the MD CONTROL buttons of the
remote control unit.
Press DISPLAY in stop mode.
DISPLAY
Each press of DISPLAY switches the displayed
information as follows.
Number of tracks and
remaining recording time
Number of tracks and
total playing time
Disc title
• A disc title composed of more than 11 characters is
scrolled, and the first 11 characters are displayed after
scrolling.
• The display shows “NO TITLE” if the disc has no title
assigned to it.
Number of tracks and total playing time
When a track has already been selected:
Number of tracks and remaining
recording time
Each press of DISPLAY switches the information as
follows.
Track No. and its playing time
Track title
• A track title composed of more than 11 characters is
scrolled, and the first 11 characters are displayed after
scrolling.
Disc title
• The display shows “NO TITLE” if the track has no title
assigned to it.
Press DISPLAY in play mode.
Each press of DISPLAY switches the information as
follows.
DISPLAY
Track No. and its playing time
Track title
• A track title composed of more than 11 characters is
scrolled, and the first 11 characters are displayed after
scrolling.
• The display shows “NO TITLE” if the track has no title
assigned to it.
16
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat playback
Repeat playback is possible in two modes. Repeat playback can be set or canceled whether the MD
is in stop or play mode. Use the MD CONTROL buttons on the normal control button panel of the
remote control unit.
1 Press REPEAT to select the repeat play mode.
Each press of REPEAT switches the repeat play modes
REPEAT
as follows.
REPEAT ALL
REPEAT 1
Off (Repeat playback canceled)
REPEAT ALL: Plays all tracks repeatedly.
REPEAT 1: Plays a single track repeatedly.
2 Press £.
/CANCEL
Repeat playback starts.
• If you are operating the main unit, press ‹/8.
To cancel repeat playback:
Main unit
Remote control unit
Press REPEAT so that the indicators turn off.
17
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Program playback
Desired MD tracks can be selected and played in the desired order.
Use the MD CONTROL buttons on the normal control button panel of the remote control unit.
1 Load an MD.
See “MD playback (Basic operation)” on page 14.
2 Press £ then immediately press 7.
This sets the numeric keys to the MD mode.
3 Press PLAY MODE to select PROGRAM.
PLAY MODE
The display shows “PROGRAM” and the PROGRAM
indicator lights up.
• If some tracks have already been programmed, the
track number and program number of each track will
be displayed.
Lights.
PROGRAM
Each press of PLAY MODE switches the play modes as
follows:
PROGRAM
RANDOM
Off (Continuous play)
• PLAY MODE can be pressed only in stop mode. Be
sure to stop MD before pressing PLAY MODE.
4 Select desired track numbers using the
numeric keys.
3
8
2
7
4
9
1
6
5
Up to 32 tracks can be programmed.
10
+
10
Track No.
Program No.
18
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Press £.
Program playback starts.
• If you are operating the main unit, press ‹/8.
/CANCEL
Program playback stops after having played all
programmed tracks.
Main unit
Remote control unit
To check the programmed tracks and their order:
Press 4 or ¢ on the remote control unit in stop
mode.
Pressing ¢ shows programmed track numbers in the
order they are programmed (if a track has a title, the
title is displayed before the track number). Pressing 4
shows them in the reverse order.
• The programmed tracks cannot be checked by
pressing 4 or ¢ on the main unit.
To cancel programmed tracks:
Press &/CANCEL in stop mode.
Each press of &/CANCEL clears the last track in the
program.
/CANCEL
If you make a mistake in programming:
Press &/CANCEL in stop mode to clear the last track in
the program until the track you programmed by mistake,
and re-program tracks from that point.
To exit program play mode:
PLAY MODE
Press PLAY MODE in stop mode and select any play
mode other than PROGRAM.
The program contents remain in memory even after the
program play mode has been exited.
• The program contents are cleared from memory when
the power cord is unplugged or in case of power
failure.
To clear the program:
INPUT
Press 0. The programmed tracks are cleared at the
moment the MD is ejected.
To play programmed tracks repeatedly:
Combine the program playback and repeat playback to
play the programmed tracks repeatedly.
For the repeat playback, see page 17.
19
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Random playback
Tracks in an MD be played in a randomly selected order by the MD recorder. The random playback
may bring you a surprising effect by playing tracks in a different order every time. Use the MD
CONTROL buttons on the normal control button panel of the remote control unit.
1 Load an MD.
See “MD playback (Basic operation)” on page 14.
2 Press PLAY MODE to select RANDOM.
PLAY MODE
The display shows “RANDOM” and the RANDOM
indicator lights up.
1
6
2
3
4
5
RANDOM
Lights.
Each press of PLAY MODE switches the play modes as
shown below.
PROGRAM
RANDOM
Off (Continuous play)
• PLAY MODE can be pressed only in stop mode. Be
sure to stop MD before pressing PLAY MODE.
3 Press £.
Random playback starts.
/CANCEL
• If you are operating the main unit, press ‹/8.
• Random playback stops after having played every
track once.
Remote control unit
Main unit
To exit random play mode:
Press PLAY MODE in stop mode and select any play
mode other than RANDOM.
PLAY MODE
To repeat random playback:
Combine the random playback and repeat playback to
play tracks repeatedly in random orders. The order
tracks are played differs every time random playback is
repeated.
For the repeat playback, see page 17.
20
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
MD recording (Basic operation)
Audio from a variety of sources can be recorded by using either digital or analog input as required.
For the remote control operation, use the MD CONTROL buttons on the normal control button panel
of the remote control unit.
1 Load a recordable MD (Mini Disc).
2 Press REC PAUSE.
The MD recorder enters record-pause mode.
REC PAUSE
CD REC
• If you are operating the remote control unit, press ¶.
Blinks.
1
REC
Main unit
Remote control unit
3 Select the input by pressing INPUT.
Each press of INPUT switches the inputs as follows.
INPUT
DIGITAL 1 IN
DIGITAL 2 IN
ANALOG IN
DIGITAL 1 IN: Select to record the digital input from the
source component connected to the DIGITAL IN 1
optical jack. (This input jack is usually connected with
optional CD player.)
DIGITAL 2 IN: Select to record the digital input from the
digital source component connected to the DIGITAL IN 2
optical jack.
ANALOG IN: Select to record the analog input from the
analog source component (cassette deck, tuner, etc.)
connected to the ANALOG IN (REC jacks).
• The input level should be adjusted when the analog
input is recorded (see page 22 for the input level
control procedure).
The input level of the digital inputs does not need
adjustment.
4 Play the source to be recorded.
5 Press ‹/8.
Recording starts.
/CANCEL
• If you are operating the remote control unit, press £.
Main unit
Remote control unit
Notes:
7
It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or
discs without the consent of the owner of copyright in the sound or video recording,
broadcast or cable program and in any literary, dramatic, musical, or artistic embodied
therein.
7
Carefully read the “Rules of Digital Dubbing”on page 50.
21
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop recording
/CANCEL
Press &/CANCEL to stop recording.
To let recording pause temporarily:
Press REC PAUSE.
REC PAUSE
CD REC
To resume recording, press ‹/8 or £ of the remote
control unit.
To adjust the analog input level
Main unit
Remote control unit
The input level should be adjusted when the analog
input is recorded.
Start playing the source before proceeding to the level
control.
1 In record-pause mode, press 4 or ¢.
The level control display appears.
REC LEVEL
1
L
R
REC
LEVEL
• The level control display appears for 5 seconds. If no
button has been pressed in this period, the display
returns to the record-pause mode display.
2 Adjust the input level by pressing 4 or ¢.
REC LEVEL
1
L
REC
R
LEVEL
Adjust so that these segments blink at the peak level.
• The level indicator blinks when the input level is too
high. Adjust the input level as described above. Too
high an input level results in distorted recording.
• The input level can be adjusted in the range from –50
to 0.
DISPLAY
To display the remaining recording time:
Press DISPLAY in record or record-pause mode.
Each press of DISPLAY switches the elapsed recording
time display and remaining recording time display
alternately.
22
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Track marking:
The track numbers on an MD (Mini Disc) are marked at
the beginning of each track. The track numbers are
identified by these “track markings” and each section
between two track markings are considered as a track.
This MD recorder can record the track markings either
automatically (AUTO) or manually (MANUAL).
• Track markings can be recorded during audio
recording.
TRACK
Automatic track marking:
MARKING
Press TRACK MARKING on the normal control button
panel of the remote control unit to select “AUTO”.
• A track marking is recorded every time a blank of 3
seconds is detected.
TRACK
Manual track marking:
MARKING
1 Press TRACK MARKING on the normal control button
panel of the remote control unit to select “MANUAL”.
SET
2 When the point you want to record a track marking
comes during recording, press SET on the editing
control button panel.
This records a track marking in the point where the
button is pressed.
• When CDs are recorded from CD player equipped
with the Compu Link remote control system. CD
player track markings are recorded automatically at
the points where the CD tracks change.
23
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
CD recording
The digital input from CDs can be recorded with a simple, one-touch operation by switching the input
automatically.
This method is available only when the Compu Link connection has been made among other optional
the components equipped with the Compu Link remote control system.
1 Load a recordable MD (Mini Disc).
2 Prepare the CD player.
Load CDs, press CD 1, CD 2 or CD 3 according to the
disc you want to record, then immediately press 7 of
the CD player. This selects the played CD.
Now set the CD player to the program play mode, etc.,
as required.
REC PAUSE
CD REC
3 Press CD REC.
The CD player and MD recorder start simultaneously
and synchronized recording starts.
• The DIGITAL 1 input is selected automatically and the
DIGITAL 1 indicator lights up.
To stop recording:
Press &/CANCEL to stop recording.
Synchronized recording of the analog input
This method is available only when the Compu Link
connection (page 48) has been made among the
components.
1 Load a recordable MD (Mini Disc).
2 Prepare the CD player.
3 Start playing a CD.
4 Press REC PAUSE.
The MD recorder enters record-pause mode.
5 Press INPUT to select the analog input and adjust the
input level (see page 22).
6 Press 7 of the CD player.
The CD player enters stop mode.
7 Press ‹/8 of the CD player.
Synchronized recording starts.
24
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio or tape recording
The analog input from an analog source component can be recorded on an MD as described below.
If you are operating the remote control unit, use the MD CONTROL buttons on the normal control
button panel.
1 Load a recordable MD (Mini Disc).
2 Prepare the amplifier/tuner or cassette deck.
With the amplifier/tuner, receive the station to be
recorded.
With the cassette deck, load the tape to be recorded.
Switch the reverse mode on if you want to record the
playback of both sides.
3 Press REC PAUSE.
The MD recorder enters record-pause mode.
REC PAUSE
CD REC
4 Press INPUT to select the analog input.
Press so that "ANALOG IN" appears on the display (see
page 21).
Main unit
Remote control unit
5 Press 4 or ¢ to adjust the input level.
See “To adjust the analog input level” on page 22.)
When recording from the cassette deck, start playing
the tape before proceeding to the input level control.
After the input level control, rewind tape to the
beginning of the music to be recorded.
REC LEVEL
6 Press ‹/8.
Recording starts.
• If you are operating the remote control unit, press £.
• When recording radio broadcast from the tuner, it is
convenient for later editing to record track markings
manually during recording (see page 23).
• When recording from the cassette deck, go to step 7.
/CANCEL
Main unit
Remote control unit
7 With the cassette deck, press ¤ or ‹.
25
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing Functions
MD editing functions
A recorded MD can be edited in many ways. The editing functions include the division, joining,
moving, erasing a single track, erasing the entire disc and assigning titles to the disc and tracks, and
more than one of them can be combined as required. Use the editing control button panel of the
remote control unit.
Dividing a track (DIVIDE) Page 28
2nd
1st
3rd
4th
This function divides a track by adding track marking(s)
in desired point(s) in the middle or where you want to
search later.
A
B
C
D
E
Track No.
After track B
division
2nd
1st
3rd
4th
5th
B
C
D
E
A
Joining a track (JOIN) Page 30
This function joins two adjacent tracks into a single track
by deleting a track marking.
2nd
1st
3rd
4th
5th
C
D
E
B
A
Track No.
After track B
joining
2nd
1st
3rd
4th
A
B
C
D
E
Moving a track (MOVE) Page 32
This function moves a track by reordering the track
numbers.
2nd
1st
3rd
4th
5th
C
D
E
B
A
Track No.
After track B
movement
2nd
1st
3rd
4th
5th
C
D
E
B
A
Erasing a track (ERASE) Page 34
2nd
1st
3rd
4th
5th
This function erases a specified track. After the erasure,
the subsequent tracks are justified and their track
numbers are decremented automatically.
C
D
E
B
A
Track No.
After track B
erasure
2nd
1st
3rd
4th
C
D
E
A
Erasing all tracks (ALL ERASE) Page 36
2nd
1st
3rd
4th
5th
This function erases data in a disc entirely.
C
D
E
B
A
Track No.
After
All Erase
26
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Combining editing functions
By combining “DIVIDE”, “ERASE” and “JOIN”, for
example, it is possible to erase only a part of existing
track.
Part to be erased
1st
2nd
3rd
B
C
A
Track No.
Dividing track A
into 3 tracks
2nd
1st
3rd
4th
5th
A
A
A
C
B
C
C
a
c
b
Track No.
Track No.
Erasing track
b
4th
3rd
1st
2nd
A
A
B
a
c
Joining
tracks
and
a
c
2nd
3rd
1st
A
A
B
a
c
Assigning titles
A title can be assigned to a track or disc. Once a title is
assigned, it is displayed in later playback for
confirmation.
Each title can be composed of up to 64 characters, and
can be input using any of character types alphabets
(uppercase and lowercase), symbols and numerals.
In the editing and title assignment operations, use the editing control buttons of the remote control unit.
TITLE
SET
EDIT
ENTER
CANCEL
SMALL
LETTER
SPACE
27
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Dividing a track (DIVIDE)
A track can be divided into desired number of tracks by adding track markings in the middle, in the
desired points or where you want to search later.
This makes it possible to assign track numbers after recording medley music or FM broadcast. The
track numbers after the divided track are incremented automatically.
1 Press EDIT to select “DIVIDE”.
EDIT
Each press of EDIT switches the editing functions as
follows.
DIVIDE
JOIN
MOVE
ERASE
MD total playing time display
ALL ERASE
1
6
2
3
4 5
Blinks.
2 Press SET.
Blinks.
SET
1
6
2
3
4 5
Blinks.
3 Play the track to be divided.
Select the track number by pressing </4 or ¢/>
then press £.
Blinks.
1
6
2
3
4
5
Blinks.
Example) When track No. 3 is selected
4 Press SET when a point where you want to
divide the track comes.
SET
“POSITION” is displayed then the track marking fine-
adjustment display appears.
Blinks.
1
6
2
7
3
4
5
Blinks.
Increments by 1.
Example)Track No. 3 and 4 blink and the 3-second
section from the divided point will be
played repeatedly.
• When the track has been divided as desired, go to
step 6.
• If the track has not been divided as desired, fine-
adjust the track marking position. Go to step 5.
• If you notice that the selected track number is wrong,
press CANCEL and select the correct track number.
28
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Fine-adjust the track marking position by
pressing </4 or ¢/>.
The track marking position can be fine-adjusted in the
range of ±128 positions (approx. ±8 sec.).
As you press the button, the track marking displaces
slightly and the 3-second section from the newly divided
point will be played repeatedly.
• After completing the fine-adjustment, go to step 6.
To correct a previously fine-adjusted track marking
position:
1 Press CANCEL.
2 Select the track number by pressing </4 or ¢/>
and press £.
3 Return to step 4.
6 Press ENTER.
The change made above is entered temporarily in the
memory. The display shows “EDITING”.
ENTER
1
6
2
7
3
4
5
7 Press 0 to eject the MD.
The data in the memory is written in the MD before it is
INPUT
ejected.
The display shows “UTOC writing” during MD write
operation.
• Be careful not to apply impact to the MD recorder
during writing data in the memory in the MD.
Otherwise the recording may be unplayable later.
• The data in the memory is written in the MD also
when the power is switched to the STANDBY mode
while “EDITING” is being displayed.
To exit editing:
Press EDIT before pressing ENTER in step 6 .
To restore the original track from the divided
tracks:
Use the JOIN editing function.
See “Joining tracks (JOIN)” on page 30.
29
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Joining tracks (JOIN)
Two adjacent tracks can be joined into a single track by deleting the unnecessary track marking. This
also makes it possible to join more than two tracks into a single track or a piece of music divided into
multiple tracks into a single piece. The track numbers after the joined tracks are decremented
automatically.
1 Press EDIT to select “JOIN”.
EDIT
Each press of EDIT switches the editing functions as
follows.
DIVIDE
JOIN
MOVE
ERASE
MD total playing time display
ALL ERASE
1
6
2
3
4 5
Blinks.
2 Press SET.
SET
Blinks.
1
6
2
3
4 5
Blinks.
3 Select the track to be joined with the previous
track.
Select the track number by pressing </4 or ¢/>.
Example) To join track numbers 1 and 2, select track
number 2 here.
Blinks.
1
6
2
3
4
5
Blinks.
Example) When track No. 2 is selected
4 Press SET.
SET
Track numbers 1 and 2 blink, indicating that these tracks
will be joined into one.
Blinks.
1
6
2
3
4
5
Blinks.
• If you selected a wrong track number, press CANCEL
and return to step 3.
30
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Press ENTER.
The change made above is entered temporarily in the
memory. The display shows “EDITING”.
ENTER
1
2
3
4
5
Decrements by 1.
6 Press 0 to eject the MD.
INPUT
The data in the memory is written in the MD before it is
ejected.
The display shows “UTOC writing” during MD write
operation.
• Be careful not to apply impact to the MD recorder
during writing data in the memory in the MD.
Otherwise the recording may be unplayable later.
• The data in the memory is written in the MD also
when the power is switched to the STANDBY mode
while “EDITING” is being displayed.
To exit editing:
Press EDIT before pressing ENTER in step 5, .
To restore the original tracks from the track
obtained by joining:
Use the DIVIDE editing function.
See “Dividing tracks (DIVIDE)” on page 28.
31
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Moving a track (MOVE)
A track can be moved to the desired position by selecting its track number and the destination track
number.
1 Press EDIT to select “MOVE”.
Each press of EDIT switches the editing functions as
EDIT
follows.
DIVIDE
JOIN
MOVE
ERASE
MD total playing time display
ALL ERASE
1
6
2
3
4 5
Blinks.
2 Press SET.
“1” for track number 1 blinks on the display.
SET
Blinks.
1
6
2
3
4 5
Blinks.
3 Select the track number to be moved, then
press SET.
SET
Select the track number by pressing </4 or ¢/>.
Blinks.
1
6
2
3
4
5
Blinks.
Example) When track No. 2 is to be moved
• If you selected a wrong track number, press CANCEL
and select the correct track number.
4 Select the movement destination track
number, then press SET.
SET
Select the track number to be given to the selected
track by pressing </4 or ¢/>.
Blinks.
1
6
2
3
4
5
Blinks.
Blinks.
Example) When track No. 5 is selected
• If you selected a wrong track number, press CANCEL
and return to step 3.
32
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Press ENTER.
ENTER
The change made above is entered temporarily in the
memory. The display shows “EDITING”.
1
6
2
3
4
5
6 Press 0 to eject the MD.
INPUT
The data in the memory is written in the MD before it is
ejected.
The display shows “UTOC writing” during MD write
operation.
• Be careful not to apply impact to the MD recorder
during writing data in the memory in the MD.
Otherwise the recording may be unplayable later.
• The data in the memory is written in the MD also
when the power is switched to the STANDBY mode
while “EDITING” is being displayed.
To exit editing:
Press EDIT before pressing ENTER in step 5.
33
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Erasing a track (ERASE)
A desired track can be erased from the MD. The track numbers after the erased track are
decremented automatically.
1 Press EDIT to select “ERASE”.
Each press of EDIT switches the editing functions as
EDIT
follows.
DIVIDE
JOIN
MOVE
ERASE
MD total playing time display
ALL ERASE
1
6
2
3
4 5
Blinks.
2 Press SET.
“1” for track number 1 blinks on the display.
SET
Blinks.
1
6
2
3
4 5
Blinks.
Blinks.
3 Select the track number to be erased, then
press SET.
SET
Select the track number by pressing </4 or ¢/>.
Blinks.
1
6
2
3
4
5
Blinks.
Example) When track No. 2 is to be erased
Blinks.
Blinks
1
6
2
3
4
5
Blinks.
Example) When SET is pressed
• If you selected a wrong track number, press CANCEL
and select the correct track number.
• If the display shows “TRACK PROTECTED”, the
selected track has been protected against accidental
erasure by other component than the MD recorder in
use. If you still want to erase the track, go to step 4.
If you will not erase it, press EDIT.
34
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Press ENTER.
ENTER
The change made above is entered temporarily in the
memory. The display shows “EDITING”.
1
2
3
4
5
Decrements by 1.
5 Press 0 to eject the MD.
INPUT
The data in the memory is written in the MD before it is
ejected.
The display shows “UTOC writing” during MD write
operation.
• Be careful not to apply impact to the MD recorder
during writing data in the memory in the MD.
Otherwise the recording may be unplayable later.
• The data in the memory is written in the MD also
when the power is switched to the STANDBY mode
while “EDITING” is being displayed.
To exit editing:
Press EDIT before pressing ENTER in step 4.
Caution
Once erased, the track can never be restored. An MD containing recording that you do not want to
erase should be protected by sliding the tab (see page 55).
35
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Erasing all tracks in an MD (ALL ERASE)
The data recorded in an MD can be erased entirely to turn the MD into a blank disc.
1 Press EDIT to select “ALL ERASE”.
Each press of EDIT switches the editing functions as
follows.
EDIT
DIVIDE
JOIN
MOVE
ERASE
MD total playing time display
ALL ERASE
1
6
2 3 4 5
Blinks.
2 Press SET.
SET
1
6
2 3 4 5
Blinks.
• If the display shows “TRACK PROTECTED”, the
selected track has been protected against accidental
erasure by other component than the MD recorder in
use. If you still want to erase the track, go to step 3.
If you will not erase it, press EDIT.
3 Press ENTER.
The change made above is entered temporarily in the
memory. The display shows “EDITING”.
ENTER
36
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Press 0 to eject the MD.
The data in the memory is written in the MD before it is
ejected.
INPUT
The display shows “UTOC writing” during MD write
operation.
• Be careful not to apply impact to the MD recorder
during writing data in the memory in the MD.
Otherwise the recording may be unplayable later.
• The data in the memory is written in the MD also
when the power is switched to the STANDBY mode
while “EDITING” is being displayed.
To exit editing:
Press EDIT before pressing ENTER in step 3.
Caution
Once erased, the tracks can never be restored. An MD containing recording that you do not want to
erase should be protected by sliding the tab (see page 55).
37
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Assigning titles to an MD and its tracks
Titles can be assigned to a recorded MD and tracks selected from it.
This operation is possible while the MD recorder is in stop mode.
1 Load a recorded MD (Mini Disc).
2 Press TITLE.
TITLE
The display shows “DISC/NO TITLE”.
1
6
2
3
4
5
Blinks.
Scrolled.
• If a disc title has already been assigned, the title is
displayed.
If you want to assign only the disc title, go to step 3.
If you want to assign the track titles, press </4 or
¢/> to select the track to be titled then go to step
3.
• To vary track numbers in the backward direction,
press 4.
1
6
2 3 4 5
Blinks.
Scrolled.
3 Press SET.
SET
The cursor starts blinking.
1
6
2 3 4 5
Blinks.
38
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Input the title.
1 Select the character case.
Each press of SMALL LETTER switches the character
case.
SMALL
LETTER
Lowercase letters can be input when the button is lit
in green, and uppercase letters can be input when the
button is not lit.
2 Input characters by pressing the character input keys.
Up to 64 characters can be input per title.
SPACE
5 Press ENTER.
ENTER
The characters input above are entered temporarily in
the memory. The display shows “EDITING”, then
scrolls the input title, and finally shows the number of
tracks and total playing time of the MD.
1
6
2 3 4 5
Blinks.
Display before ENTER is pressed
1
6
2 3 4 5
Display after ENTER is pressed
Scrolled display of input title
1
6
2 3 4 5
1
6
2 3 4 5
39
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Press 0 to eject the MD.
The data in the memory is written in the MD before it is
ejected.
INPUT
The display shows “UTOC writing” during MD write
operation.
• Be careful not to apply impact to the MD recorder
during writing data in the memory in the MD.
Otherwise the recording may be unplayable later.
• The data in the memory is written in the MD also
when the power is switched to the STANDBY mode
while “EDITING” is being displayed.
To correct input characters:
Characters can be corrected only before ENTER is
pressed.
1 Press </4 or ¢/> to move the cursor to the
character to be corrected.
CANCEL
2 Press CANCEL to erase the character.
3 Input the correct character.
To cancel all input characters:
Characters can be cleared only before ENTER is
pressed.
Press CANCEL to erase all characters then press TITLE.
To exit editing:
Press TITLE before pressing ENTER.
40
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Assigning titles while playback or recording
Track titles can be assigned as you play or record the tracks.
1 After start of playback or recording of a track,
TITLE
press TITLE.
1
6
2
3
4
5
Blinks.
2 Input the track title.
SMALL
LETTER
1 Select the character case.
Each press of SMALL LETTER switches the character
case.
Lowercase letters can be input when the button is lit
in green, and uppercase letters can be input when the
button is not lit.
2 Input characters by pressing the character input keys.
Up to 64 characters can be input per title.
SPACE
3 Press ENTER.
ENTER
The characters input above are entered temporarily in
the memory. The display shows “EDITING”.
• If it is during playback, the track will be played
repeatedly until ENTER is pressed.
Pressing ENTER stops the playback.
• If it is during recording, recording continues even
after ENTER is pressed.
If ENTER is not pressed until the end of the track, the
characters input before the end of the track are
recorded.
4 Press 0 to eject the MD.
The data in the memory is written in the MD before it is
ejected.
INPUT
The display shows “UTOC writing” during MD write
operation.
• Be careful not to apply impact to the MD recorder
during writing data in the memory in the MD.
Otherwise the recording may be unplayable later.
• The data in the memory is written in the MD also
when the power is switched to the STANDBY mode
while “EDITING” is being displayed.
41
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
To correct input characters:
Characters can be corrected only before ENTER is
pressed.
1 Press </4 or ¢/> to move the cursor to the
character to be corrected.
CANCEL
2 Press CANCEL to erase the character.
3 Input the correct character.
To cancel all input characters:
Characters can be cleared only before ENTER is
pressed.
Press CANCEL to erase all characters then press TITLE.
To exit editing:
Press TITLE before pressing ENTER.
42
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control of the othe Components
Remote control of the other optional components from the provided
remote control unit
The remote control unit provided with the MD recorder can be used to control the amplifier/tuner CD
player and cassette deck equipped with the Compu Link remote control system. The amplifier/tuner
is controlled directly while the CD player and cassette deck are controlled with the help of the Compu
Link system (page 48).
Point the remote control unit to the remote control sensor of the amplifier/tuner to operate other
components.
RX-EX70 INTEGRATED AMPLIFIER
/
TUNER
VOLUME
Remote controlling the amplifier/tuner
BAND
INPUT
S. A. BASS
DIRECT
PHONES
(Page 44)
DOWN
UP
STANDBY
POWER
KEY
MODE
The amplifier, tuner and timer operations can be
controlled.
To switch the amplifier power between ON and
STANDBY from the remote control unit provided with
the MD recorder, set the POWER control mode to the
amplifier/tuner mode.
Switching the POWER button’s control mode
Amplifier/tuner mode:
Press POWER and “1” on the normal control button
panel simultaneously.
POWER
This makes it possible to switch the amplifier/tuner
power between ON and STANDBY.
• In this mode, the MD recorder power cannot be
switched between ON and STANDBY by remote
control.
3
4
2
7
1
6
5
8
9
10
FM MODE
/ MUTING
TUNER
AUX
+
10
MD recorder mode:
Press POWER and “10” on the normal control button
panel simultaneously.
POWER
This makes it possible to switch the MD recorder power
between ON and STANDBY.
• In this mode, the amplifier/tuner power cannot be
switched between ON and STANDBY by remote
control.
3
8
4
2
7
1
5
9
6
10
FM MODE
/ MUTING
UNER
X
+
10
Remote controlling the CD player (Page 46)
Remote controlling the cassette deck (Page 46)
43
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote controlling the amplifier/tuner
The remote control unit can control the amplifier/tuner equipped with the Compu Link remote control
system directly.
POWER
3
8
2
7
4
1
6
5
9
10
FM MODE
/ MUTING
TUNER
AUX
Amplifier/tuner control buttons
+
10
CLOCK
/ TIMER
SLEEP
UP
SET
CANCEL
DOWN
CD CONTROL
PLAY MODE REPEAT
CD 1
CD 2
CD 3
MD CONTROL
TRACK
PLAY MODE REPEAT
DISPLAY
MARKING
TAPE CONTROL
BASS
TREBLE
BALANCE
– / L
+ / R
FADE
MUTING
S.A.BASS
VOLUME
RM-SEEX90MU REMOTE CONTROL
44
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
VOLUME +/–:
Adjust the volume.
Pressing + increases the volume and
pressing – decreases it.
POWER:
Switches the power between ON and
STANDBY.
• Before remote controlling the amplifier/
tuner, set the POWER control mode to the
amplifier/tuner mode (see page 43).
FADE MUTING:
Sets the volume to 0. Pressing again returns
to the original volume.
Numeric keys (1 to 10, +10):
Selects preset channels.
For detailed operation description, refer to the
instruction manual of the amplifier/tuner
(RX-EX70/90).
* In the timer setting and clock setting, use
DOWN and UP of the remote control unit
provided with the MD recorder, in place of +/R
and –/L as described in the amplifier/tuner’s
instruction manual.
FM MODE/MUTING:
Press to switch the FM mode between
AUTO and MONO.
TUNER:
Press to select the tuner as the sound source
and set the numeric keys (1 to 10 , +10) on
the remote control unit to operate the tuner.
Press repeatedly to switch the band (FM or
AM).
AUX:
Press to select the component connected to
the amplifier/tuner’s AUX jacks as the sound
source.
SLEEP:
Sets or releases the sleep timer.
CLOCK/TIMER
Used when setting the timer or clock.
SET:
Sets a timer or clock.
CANCEL:
Cancels a timer operation.
DOWN, UP:
Used when setting the timer or clock.
BASS:
Used when controlling low frequencies. After
pressing BASS, adjust the level by pressing
+/R or –/L.
TREBLE:
Used when controlling high frequencies.
After pressing TREBLE, adjust the level by
pressing +/R or –/L.
BALANCE:
Used when controlling the balance between
the left and right channels. After pressing
BALANCE, adjust the level by pressing +/R or
–/L.
+/R, –/L:
Press when setting the balance, treble and
bass.
S. A. BASS:
Switches the function for enhancing the low
frequencies.
45
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote controlling the CD player and cassette deck
The remote control unit can control CD player and cassette deck equipped with the Compu Link
remote control system (page 48).
Always point the remote control unit to the remote control sensor on the amplifier/tuner.
CD player control buttons
£: Starts playback.
7: Stops playback or recording.
4, ¢: Skips to the beginning of a track.
PLAY MODE: Switches the play modes.
REPEAT: Switches the repeat play modes.
CD 1: Plays the CD with disc number 1.
CD 2: Plays the CD with disc number 2.
CD 3: Plays the CD with disc number 3.
Pressing £ or CD 1, CD 2 or CD 3 sets the numeric keys
to the CD control mode.
Numeric keys
1 to 10, +10: Used to select a track number directly.
Track No. 5: Press 5.
Track No. 15: Press +10 then 5.
Track No. 20: Press +10 then 10.
Track No. 32: Press +10 three times then press 2.
Cassette deck control buttons
™, £: Starts playback.
7: Stops playback or recording.
1, ¡: In play mode, skips to the beginning of a tune
(Music Scan). In stop mode, fast forwards or rewinds
tape.
¶: Initiates record-pause mode.
POWER
3
8
4
2
7
1
6
5
9
10
FM MODE
/ MUTING
TUNER
AUX
+
10
CLOCK
/ TIMER
SLEEP
UP
CD player
control buttons
SET
CANCEL
DOWN
CD CONTROL
PLAY MODE REPEAT
CD
1
CD
2
CD
3
MD CONTROL
TRACK
PLAY MODE REPEAT
DISPLAY
MARKING
TAPE CONTROL
Cassette deck
control buttons
BASS
TREBLE
BALANCE
– / L
+ / R
FADE
MUTING
S.A.BASS
VOLUME
RM-SEEX90MU REMOTE CONTROL
46
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Examples
Program playback of CDs
1 Press £ then immediately press 7.
This sets the numeric keys of the remote control unit to
the CD mode.
PLAY MODE
2 While the CD player is in stop mode, press
PLAY MODE to select “PROGRAM”.
CD 1
CD 2
CD 3
3 Select a disc number.
Press CD 1, CD 2 or CD 3.
3
8
2
7
4
9
1
6
5
4 Select a track number using the numeric keys.
10
+
10
5 Program other tracks by repeating steps 3
and 4.
6 Press £.
Program playback starts.
Recording of cassette tapes
1 Load the tape for use in recording in the tape
tray of the cassette deck.
2 Press ¶.
The cassette deck enters record-pause mode.
3 Play the source to be recorded.
4 Press ™ or £.
Recording starts.
47
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPU LINK
Linked Operation of the Other Optional Components (Compu Link)
The EX series components can be controlled under linked operation provided by the JVC’s Compu
Link remote control system.
What is Compu Link
The world of single components, in which you purchase a cassette deck, CD player, amplifier and
other components separately and enjoy your own composition, is an effective means for pursuit of
high-quality reproduction. However, in terms of operability, the need of controlling components
independently makes their control complicated and their linked operation impossible. Then, isn’t it
possible to combine single component and control them as simply as an integrated audio system?
The Compu Link remote control system is the response to such a requirement.
The components in the JVC EX series are equipped with jacks named COMPU LINK-3 (COMPU LINK
jacks). By connecting the COMPU LINK jacks of these components, they can be controlled simply
with a systematized, linked operation.
Compu Link connections
Using Compu Link cables, connect the COMPU LINK jacks of EX series components. Connect so that
the Compu Link cables can bridge all of the EX series components you have. The components can be
connected in any order.
48
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Shortcut playback
Simply selecting an input source of the amplifier/tuner starts playback of the selected source
component (CD player, MD recorder or cassette deck).
Also, even if you do not touch the amplifier/tuner, starting playback of a source component sets the
amplifier’s input source automatically to the played component.
*Refer to the instruction manual of amplifier/tuner.
A single remote control unit
The remote control unit provided with the amplifier/tuner can also be used to control the CD player or
cassette deck.
(See “Remote Control of the Other Optional Components” on page 43.)
Synchronized recording
Recording can be started automatically in synchronism with the start of playback of a source
component.
Timer operation
The timer function built into the amplifier/tuner can be used to start recording or playback of other
components at the reserved time of the day or switch the power to the STANDBY mode in the
reserved time period.
*Refer to the instruction manual of amplifier/tuner.
49
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Rule on Digital Copying
The digital audio equipment exchange audio signals in the digital forms through digital input/output
jacks, and include the CD (Compact Disc) player, MD (Mini Disc) recorder and DAT (Digital Audio
Tape) recorder. The digital audio equipment allows digital copy of signals with little deterioration of
music signals. This has made it necessary to have a copy restriction rule for protecting the copyright,
and the SCMS has been established as a result.
SCMS (Serial Copy Management System)
With a view to protecting the copyright, the SCMS restricts the number of generations permitted for
copying of signals in the digital form between digital audio equipment to only one generation.
2nd generation
1st generation
Caution
Because of this rule, the MD obtained by recording a CD on the MD recorder cannot be copied in the
digital form on other digital equipment.
50
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
About MD (Mini Disc)
The MD (Mini Disc) is a new digital audio medium using a disc with a diameter of 64 millimeters. In
spite of the small size, the MD has multiple functions, high audio quality and recording/playback
capabilities for up to 74 minutes.
Role of the cartridge
The MD cartridge has a pocket size of 68 mm x 72 mm
with a thickness of 5 mm. The cartridge accommodates the
Cartridge
64 mm diameter disc for ease of transportation and
storage.
The internal disc is usually protected by the cartridge shells
and shutter so no dust, dirt, scratch or fingerprint is left on
the disc and the disc handling is easy.
Disc
Cartridge
Shutter
Two disc types
The MD (Mini Disc) includes two disc types, the recordable MD that can be recorded onto and the
playback-only MD that can exclusively be played back. Although both types of discs are played in the
same way, that is, by irradiating a laser beam on the disc and reading signals from the reflected light,
the ways they are recorded are completely different.
Playback-only MD
This type of disc is used in prerecorded MD software
marketed in music stores. It cannot be recorded by the user
and data is recorded in the same way as a CD, i.e.
Sound Cruise
according to the presence or absence of small holes called
pits. A disc recorded in this way is referred to as an “optical
disc”.
Playback-only MD
Recordable MD
This type of disc records data using the magnetism to allow
repeated data recording operations. A disc recorded in this
way is referred to as an “MO (Magneto-Optical) disc”.
Recordable MD
51
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
ATRAC (Adaptive TRansform Acoustic Coding)
The MD (Mini Disc) has half the size of the CD but can
(dB)
record data for the same period of time. This has been
made possible by the newly developed ATRAC (Adaptive
TRansform Acoustic Coding), which compresses data by
cutting the audio components that are inaudible to the
human sense of audition. This technology reduces the
recorded data to about 1/5 the original data quantity and
enables recording/playback of data for up to 74 minutes.
+20
High
0
-20
Ear
sens.
-40
-60
Low
5k 10k 15k
20 50 100
500 1k
High (Hz)
Audio
freq.
Low
Sound skip guard memory
The sound skip guard memory stores some data of the
played track so that the played audio does not skip due to
vibration during MD (Mini Disc) playback.
In case the optical laser cannot read disc signal due to
vibration, the actually reproduced audio is not interrupted
because the data stored in the guard memory is available.
stop
During normal
playback
During vibration
UTOC (User Table Of Contents)
The recordable MD (Mini Disc) contains the recording of
UTOC (User Table Of Contents) in addition to music data
itself. The UTOC includes the information on the positions
the tracks are recorded, markings between tracks and order
of tracks, so tracks can be searched quickly by referring to
it. The editing operations consist of altering the UTOC
contents and the actual music data does not need to be re-
recorded.
UTOC
Contents
1st tune...
2nd tune...
3rd tune...
Music data
52
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
MD Error Messages
The display of the MD recorder may show the error messages which are explained in the following
table.
Error Messages
Description
Treatment
BLANK DISC
The loaded disc is a non-recorded
disc.
Use a recorded disc unless you
want to start recording on a
blank disc.
CANNOT JOIN
An attempt is made to join tracks
that cannot be joined.
This is one of system
restrictions on the MD. [See
page 54.]
DISC ERROR
DISC FULL
The MD is abnormal (damaged).
Use another MD.
The disc has no available space or
the number of tracks has reached
254.
Use another recordable MD.
EMERGENCY STOP
NO DISC
An abnormality occurred during
recording.
Press &/CANCEL to enter stop
mode, then press 0 to eject
the MD and retry recording.
No MD is loaded.
Load an MD.
NON-AUDIO
CANNOT COPY
An attempt is made to digitally dub a
CD-ROM (Video CD, etc.).
Stop recording.
PLAYBACK DISC
An attempt is made to record on or
edit a playback-only MD.
Use a recordable MD.
DISC PROTECTED
The MD is protected against
accidental erasure.
Slide the protect tab of the
MD. [See page 55.]
TRACK PROTECTED
A track has been protected against
accidental erasure by other
component that the MD recorder in
use.
This protection cannot be
released by the MD recorder
being used. Release it using
the MD recorder which
activated the protection.
SCMS CANNOT COPY
DIGITAL IN UNLOCK
An attempt is made to copy a
digitally dubbed copy.
Use the analog input for
recording.
A wrong digital input is selected.
Press INPUT to select the
correct digital input.
53
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
MD Restrictions
The MD uses a unique data recording format that is different from the formats used by Cassettes
tape and DAT. Due to the restrictions imposed by this MD recording format, following symptoms may
be observed. Note that these symptoms do not indicate malfunction of the product.
Symptom
Cause
“DISC FULL” is displayed
before the available recording
time indicated on the disc has
been used.
The number of tracks that can be recorded on an MD is limited
regardless of the time period. It is not possible to record a 255th
track.
“DISC FULL” is displayed
although there remains margin
in both the number of tracks
and available recording time.
After partial erasure and re-recording are repeated, the disc comes
to contain many idle spaces here and there. When recording data
on such a disc, the MD recorder distributes the data of a single
track in many locations. When such separated sections increase,
“DISC FULL” may be displayed during recording.
The JOIN operation is not
possible.
When a section below 8 seconds is created by separation, the
track containing it cannot be joined with another track using the
JOIN function, and the remaining recording time does not increase
even when such a section is erased. Also, the audio may be
interrupted after fast forwarding or fast reversing a track recorded
in separate sections.
The remaining recording time
does not increase after some
tracks are erased.
Sound is interrupted after fast
forward or fast reverse.
The total of the elapsed
recording time and remaining
recording time is less than the
available recording time
indicated on the disc.
The MD always spend a continuous space of at least 2 seconds
for recording data even when it is shorter than 2 seconds. When a
large number of non-used spaces below 2 seconds are produced
in a disc as a result of the above, the available recording time in
the disc is shortened.
54
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Handling MDs
MD handling precautions
To maintain high quality audio for a long period
Since the disc is accommodated inside a cartridge, it
can be handled easily without caring about dust and
dirt. However, to maintain the high audio quality for an
extended period, use care in the following points.
Installation location
Do not install the MD in following places.
• In a place subject to direct sunlight or where the
temperature rises, for example in a closed
automobile. The disc may be warped and unusable in
these places.
• In a bathroom or where the humidity is high. The disc
may be rusted in these places.
• On a beach or sandbox. The disc surface may be
scratched or damaged if grit penetrates through an
opening on the cartridge.
Periodical maintenance
When the cartridge gets dusty or dirty, wipe with a soft,
dry cloth.
Do not open the shutter.
The shutter is usually locked to prevent opening. Do not
force to open it or the disc may be destroyed.
To protect important recording
A recordable MD has a sliding tab for protection against
accidental erasure of important recording.
After recording or editing, slide open the accidental
erasure protect tab on the cartridge edge to make
additional recording or editing impossible. If you want to
re-record or edit the disc, slide the protect tab again.
Protect tab
Recording/editing
possible
Recording/editing
not possible
55
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Troubleshooting
In case of difficulty, check the following before calling for service.
Symptom
Cause
Treatment
Sound is not heard.
•
Cables are not connected
•
Connect cables properly by
properly.
referring to “Connection”.
•
The power cord is unplugged
from the power outlet.
•
Plug the power cord
securely into the power
outlet.
Recording is not possible.
•
•
A playback-only MD is loaded.
•
•
Use a recordable MD.
The MD is protected against
accidental erasure (“DISC
PROTECTED” is displayed in
this case).
Slide close the accidental
erasure protect tab of the
MD.
Remote control is not
possible.
•
•
•
The batteries are exhausted.
•
•
•
Replace batteries with new
ones.
The batteries are inserted with
wrong polarity (+, –).
Insert batteries with correct
polarity.
There is an obstacle between
the remote control unit and
remote control sensor.
Remove the obstacle.
•
•
The remote control sensor is
under direct sunlight.
•
•
Screen the direct sunlight.
The MD recorder power
cannot be switched ON/
STANDBY with POWER of
the remote control unit.
POWER is set to the amplifier/
tuner mode.
Press POWER and “10”
simultaneously to set
POWER to the MD recorder
mode.
•
•
Condensation is produced
inside the MD recorder
immediately after starting the
room heating or when it is
transported from a cold to
warm place.
•
•
Unplug the power cord,
wait a few hours and plug it
again.
Operation is abnormal.
The microcomputer is
malfunctioning due to external
noise or lightning.
Unplug the power cord then
plug it in again.
56
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Format
Recording format
Reading format
Minidisc digital audio system
Magnetic modulation overwrite format
Non-contacting optical method by
semiconductor laser (λ=780nm)
44.1 kHz
Sampling frequency
Compression/expansion method
Number of channels
Frequency Response
S/N ratio
ATRAC (Adaptive Transform Acoustic Coding) method
2 channels
5 Hz to 20,000Hz (±0.5dB)
93dB
Dynamic range
91dB
Wow/flutter
Less than measurable limit
Input terminals
(Analog)
ANALOG IN (pin jack),
OPTICAL DIGITAL IN (square optical connector jack)
Terminal name Reference input level Minimum input level
ANALOG IN 275mV rms.
100mV rms.
Received optical
Terminal name signal wave length Input level
(Digital)
DIGITAL IN
1 , 2
660nm
–23dBm to –15dBm
Output terminal
(Analog)
ANALOG OUT(pin jack)
Terminal name
ANALOG OUT
Load impedance
10k ohms
Output level
1.1V
Power requirements
Power consumption
Demensions
AC120V , 60Hz
11 watts (ON), 6 watts (STANDBY)
200 × 80 × 308.5 mm (W/H/D)
(7-7/8 × 3-3/16 × 12-3/16 inches)
2.3kg (5.1 lbs)
Mass
Remote control unit (1)
Accessories
Batteries (R03(UM-4)/AAA (24F)) (2)
Audio pin cord (2)
Optical digital cord (1)
Compu link cable (1)
AC power cord (1)
Specifications and appearance subject to change for improvements without prior notice.
57
XM-EX90
Download from Www.Somanuals.com. All Manuals Search And Download.
QUALITY
SERVICE
HOW TO LOCATE YOUR JVC SERVICE CENTER
TOLL FREE : 1-800-537-5722
Dear customer:
In order to receive the most satisfaction from your purchase, read the instruction booklet before operating the unit. In the event that
repairisnecessary,orfortheaddressnearestyourlocation,pleaserefertothefactoryservicecenterlistbeloworwithintheContinental
United States, Call 1-800-537—5722 for your authorized servicer. Remember to retain you Bill of Sale for Warranty Service.
—JVC
JVC SERVICE & ENGINEERING
COMPANY OF AMERICA
DIVISION OF US JVC CORP.
FACTORY SERVICE CENTER LOCATIONS
107 Little Falls Road
Fairfield, NJ 07004-2105
(201) 808-9279
1500 Lakes Parkway
Lawrenceville, GA 30243-5357
(770) 339-2522
705 Enterprise Street
Aurora, IL 60504-8149
(630) 851-7855
5665 Corporate Avenue
Cypress, CA 90630-0024
(714) 229-8011
2969 Mapunapuna Place
Honolulu, HI 96819-2040
(808) 833-5828
10700 Hammerly, Suite 110
Houston, TX77043
(713) 935-9331
230 Eliot Street
Ashland, MA 0172-2377
(508) 881-5923
14505 Commerce Way
Miami Lakes, FL 33016-1512
(305) 362-6252
890 Dubuque Avenue
South San Francisco, CA 94080-1804
(415) 871-2666
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production of
the wide array of JVC products, service is the key to maintaining the high level of performance for which JVC is world famous. The
JVC service and engineering organization stands behind our products.
NATIONAL HEADQUARTERS
JVC SERVICE & ENGINEERING COMPANY OF AMERICA
DIVISION OF US JVC CORP.
107 Little Falls Road
Fairfield, NJ 07004-2105
If you ship the product • • •
Don’t service it yourself.
Pack your JVC unit in the original carton or one of equivalent
size and strength. Enclose, with the unit, a letter stating the
problem or symptom that exists and also a copy of the receipt
CAUTION
or bill of sale you received when you purchased your JVC unit.
Print your home return address on the outside and the inside
of the carton. Send to the appropriate JVC Factory Service
Center as listed above.
To prevent electrical shock, do not open the cabinet. No user
serviceable parts inside.
Refer servicing to qualified service personnel.
ACCESSORIES
To purchase accessories for your JVC product, you may contact your local JVC Dealer.
Or from the 48 Continental United States call toll free : 800-882-2345
(0694)
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY AUDIO-1
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL
PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIAL AND WORKMANSHIP from the date of original retail
purchase for the period as shown below. (“The Warranty Period.”)
PARTS
LABOR
1YR
1YR
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY(50) UNITED STATES, THE DISTRICT OF COLUMBIA AND IN
COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such
repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers.
Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may be
brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and
above which are covered on an in-home basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized
service center, please call toll free: (800)537-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of
your bill of sale plus and letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location
of which will be given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty
installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to
render such service, or if affixed to any attachment not provided with the products, or if the model or serial number has
been altered, tampered with, defaced or removed;
2. Initial installation and installation and removal for repair;
3. Operational adjustments covered in the Owner’s Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus(Needle) are covered for 90 days from the date of purchase;
7. Accessories;
8. Batteries (except the Rechargeable Batteries are covered for 90 days from the date of purchase);
There are no express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MARCHANTABILITY, IS
LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER
DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO
TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH
OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET
FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied
warranty last, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state.
JVC COMPANY OF AMERICA
DIVISION OF US JVC CORP.
41 Slater Drive
Elmwood Park, New Jersey 07407
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF
REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION
PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain this
information for future reference.
Model No.:
Serial No.:
Purchase date:
Name of dealer:
Download from Www.Somanuals.com. All Manuals Search And Download.
VICTOR COMPANY OF JAPAN, LIMITED
EN.
J
C
V
0598TTMWSTOZK
Download from Www.Somanuals.com. All Manuals Search And Download.
|