Surround Cinema Series
Models: SCS150SI
SCS160SI
SCS180.6S
Home Theater Speaker Systems
SERVICE MANUAL
JBL Consumer Products
250 Crossways Park Dr.
Woodbury, New York 11797
Rev4 10/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
150W Powered Sub/ Plate Amp
LINE VOLTAGE
US 120vac/60Hz
Asia 100vac/50Hz
Yes/No
Yes
Yes
Hi/Lo Line
108-132
90-110
Unit
Notes
Normal Operation
Normal Operation
Vrms
Vrms
Parameter
Specification
Unit
QA Test Limits
Conditions
Notes
Amp Section
Type (Class AB, D, other)
Load Impedance (speaker)
Rated Output Power
THD@ Rated Power
THD @ 1 Watt
D D
4 Ohms
150 Watts
0.08 %
0.1 %
10 mV-DC
n/a
n/a
145
1
0.5
20
Nominal
1 input driven
22k filter
22k filter
@ Speaker Outputs
DC Offset
Measured at speaker terminals, Output
power 140 Watts THD 0.1 %
Damping factor
>100 DF
30
Input Sensitivity
Input Frequency
Line Input (L&R)
LFE Input
50 Hz
50
Nominal Freq.
1 input driven
1 input driven
LFE input driven only
(-20 dB below Line In)...1 input driven
250 mVrms
145 mVrms
2 Vrms
±2dB
±2dB
±2dB
To Rated Power
To Rated Power
To Rated Power
Speaker/Hi Level Input
Signal to Noise
SNR-A-Weighted
SNR-unweighted
SNR @ 1W-unweighted
100 dBA
90 dBr
60 dBr
85
80
55
rel. to rated power
rel. to rated power
rel. to 1W Output
A-Weighting filter
22k filter
22k filter
Volume @max, using RMS reading
DMM/VOM (or A/P)
Residual Noise Floor
1 mVrms
2
2
Volume @max, w/ A/P Swept Bandpass
Measurement (Line freq.+ harmonics)
Residual Noise Floor
1 mVrms(max)
Input Impedance
Line input L&R , LFE
Speaker/Hi Level Input
>15 K ohms
4.7 K ohms
n/a
n/a
Nominal
Nominal
Filters
Left & Right Low Pass fixed
Slope & Q
LFE Low Pass fixed
Slope & Q
Subsonic filter (HPF)
Slope & Q
Hz
4th dB/Octave
Hz --
2nd dB/Octave
Hz --
2nd dB/Octave
--
±2dB
n/a
±2dB
n/a
±2dB
n/a
Limiter
YES
--
n/a
Features
LFE Input
Volume pot Taper (lin/log)
ATO
YES
log
YES
functional
functional
functional
BW Limited to 500 Hz
--
Signal Sensing (ATO)
ATO test Frequency
ATO Line Level
50 Hz
functional
functional
fucntional
2mV@50Hz into Line Input w/ 1 ch.
2 mV
driven
50mV@50Hz into Line Input w/ 1 ch.
ATO Speaker level input
50 mV
driven
Amp connected and AC on, then input
signal applied
T before muting, after signal is removed Auto turn of time (T) must be 10 > T <15
ATO Turn-on time
Auto Mute/ Turn-OFF Time
5 ms
15 minutes
functional
functional
Power on Delay time
3 sec.
functional
AC Power Applied
Transients/Pops
ATO Transient
Turn-on Transient
Turn-off Transient
5 mV-peak
50 mV-peak
50 mV-peak
10
100
100
@ Speaker Outputs
@ Speaker Outputs
@ Speaker Outputs
AC Line cycled from OFF to ON
AC Line cycled from ON to OFF
Efficiency
Maximum allowable input power under
nominal Input voltage and frequency, HOT
or COLD operation.
Stand-by Input Power
Power Cons.@rated power
14 Watts
230 Watts
16
250
@ nom. line voltage
@ nom. line voltage
140 Watts @ 4 Ohms nominal line voltage
Protection
Short Circuit Protection
YES
--
functional
Direct short at output
Temperature rise should not exceed 35K
rise
Relay or crowbar (for driver/fire protection)
Thermal Protection
DC Offset Protection
Line Fuse Rating
US Version
65 deg. C
YES
--
--
functional
functional
@1/8 max unclipped Power
DC present at Speaker Out leads
3.15 Amps
Type-T or Slo Blo
External fuse with UL/SEMKO rated holder
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
S P EAKER CONNECTIONS
Connection Tips
To use the binding-post
speaker terminals on the
subwoofer, unscrew the
colored collar until the pass
through hole in the center
post is visible under the
collar. Insert the bare end of
the wire through this hole;
then screw the collar down
until the connection is tight.
The hole in the center of
each collar is intended for
use with banana-type
connectors.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
Dolby* Pro Logic* (Non-Digital) – Speaker Level
Left Front
Right Front
Use this installation method
for Dolby Pro Logic appli-
cations (not Dolby Digital,
DTS® or other digital
Center
+
–
+
–
+
–
processing), where the
receiver/processor does not
have a subwoofer output, or
a volume-controlled preamp
(line-) level output:
Subwoofer
HIGH LEVEL
Connect your receiver or
amplifier’s front left and right
speaker terminals to the left
and right terminals on the
subwoofer that are marked
“High Level In.” Connect the
left and right terminals on the
subwoofer that are marked
“High Level Out” to the cor-
responding terminals on the
back of your front left and
right speakers.
L
R
+
–
–
+
OUT
IN
Receiver
Left Front
Center
Right Front
+
–
+
–
+
–
Connect your receiver or
amplifier’s center, left and
right surround-speaker
terminals to the corre-
Left Surround
Right Surround
sponding terminals on the
back of your center, left and
right surround speakers.
+
–
+
–
Left Surround
Right Surround
+
–
+
–
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
Dolby Pro Logic (Non-Digital) – Line Level
Use this installation method
for Dolby Pro Logic appli-
Use RCA-type patch cords
Pro Logic processors. Note: If
your receiver or amplifier only
has one subwoofer output
jack, then you will need to use
a Y-connector (not included).
Plug the male end of the Y-
connector into your receiver
or amplifier’s subwoofer
to connect the line-level
subwoofer outputs on your
receiver or amplifier to the
line-level inputs on the
subwoofer. IMPORTANT: Do
not use the LFE input on the
subwoofer with Dolby
cations (not Dolby Digital, DTS
or other digital processing),
where the receiver/processor
is equipped with a subwoofer
output, or a volume-controlled
preamp (line-) level output:
output jack, and connect each
of the two female ends to
separate RCA-type patch
Center
Left Front
Right Front
+
–
+
–
+
–
cords. Finally, plug the RCA-
type patch cords into the line-
level inputs on the subwoofer.
Subwoofer
Line-
Level
In
Connect each speaker to
the corresponding speaker
terminals on your receiver
or amplifier.
L
R
Make sure your receiver or
processor is correctly
configured to indicate that the
subwoofer is “On.”
Receiver
Left
Front
Subwoofer
Out
Right
Front
+
+
–
–
–
R
L
Note for advanced users: If
your receiver/processor has a
built-in low-pass crossover
filter for the subwoofer output,
you may use the LFE input to
bypass the subwoofer’s
Left
Rear
Right
Rear
+
Center
+
+
–
–
Right Surround
Left Surround
internal crossover.
+
–
+
–
Dolby Digital or DTS (or Other Digital Surround Mode) Connection
Use this installation method
for Dolby Digital, DTS or other
digital surround processors:
terminals on your receiver
or amplifier.
RECEIVER
LFE OUT
SUBWOOFER
LINE LEVEL IN
Make sure that you have
configured your surround-
sound processor for
“Subwoofer On.” The front
left, front right, center and
rear speakers should all be
set to “Small.”
L
Use the line-level input jack
marked “LFE” for the Low-
Frequency Effects channel.
Connect this jack to the LFE
output or subwoofer output
on your receiver or amplifier.
Connect each speaker to the
corresponding speaker
LFE INPUT
R
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
OP ERATION
Move the Master Power
is not sending program
When the “Auto/On” switch
™ is switched to the “On”
position, the subwoofer will
remain on, whether or not
program material is playing.
If you will be away from
home for an extended period
of time, or if the subwoofer
will not be used, switch the
Master Power switch ¡ to
the Off position.
switch (marked “Power” ¡)
material to the subwoofer,
the subwoofer will be in
standby mode. When the sub-
woofer senses an audio signal,
it will automatically turn itself
on. If the subwoofer does
not sense a signal after
to the “ ” (On) position to use
•
the subwoofer. The
subwoofer will automatically
turn itself on or go into
standby (sleep) mode when
left in the standby mode
(“Auto/On” switch ™ in the
“Auto” position). When your
receiver or amplifier is off, or
approximately twenty minutes,
it will automatically go into
standby mode.
™
HIGH LEVEL
SUBWOOFER
LEVEL
LINE LEVEL IN
LFE
+
–
–
+
L
R
OUT
IN
L
AUTO
ON
£
R
MIN
MAX
GREEN: ON
RED: STANDBY
+
IMPORTANT: CONNECT STRIPED WIRE TO RED
(
)
SPEAKER TERMINAL.
3.15A/250V
TYPE T
WARNING: FOR CONTINUED
PROTECTION AGAINST RISK
OF FIRE, REPLACE ONLY WITH
SAME TYPE 3.15A, 250 VOLT FUSE
AVERTISSEMENT: UTILISEZ UN
FUSIBLE DE RECHANGE DE MEME
TYPE 3.15A, 250V
POWER
JBL, Incorporated
A Harman International Company
¡
This area is designed to become quite warm
during normal operation
AC 120V~60Hz
250 Watts
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS : RISQUE DE CHOC ÉLECTRIQUE-NE PAS OUVRIR
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
AVERTISSEMENT: POUR PRÉVENIR LES RISQUES D'INCENDIE
OU DE CHOC ÉLECTRIQUE, ÉVITER D'EXPOSER CET APPAREIL
A LA PLUIE OU A L'HUMIDITÉ.
Volume
Volume can be adjusted
using the Subwoofer Level
Control £ (above), as shown
below.
Subwoofer
Level
Subwoofer
Level
MIN
MAX
MIN
MAX
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
TROUBLES HOOTING
If there is no sound from any
of the speakers:
that is working correctly. Turn
everything back on, and
determine whether the
problem is in the same place,
i.e., the speaker that was
is not in phantom mode.
• If your receiver/processor
is set in Dolby Digital or DTS
mode, make sure the
receiver/processor is con-
figured so that the center
speaker is enabled.
• Check that receiver/amplifier
is on and a source is playing.
• Check that the powered
subwoofer is plugged in, and
its Power switch ¡ is
working previously now has
no sound and the speaker that
was not working now sounds
fine; or whether it has moved,
i.e., the speaker that was not
working still has no sound and
the speaker that was working
is still fine. If the problem is in
the same place, the source of
the problem is most likely with
your receiver or amplifier, and
you should consult the owner’s
manual for that product for
further information. If the
problem has followed the
speaker, consult your dealer
for further assistance or, if
that is not possible, visit our
further information.
switched on to the “ ”
•
position.
If the system plays at low
volumes but shuts off as
volume is increased:
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
speaker wires are frayed, cut
or punctured.
• If more than one pair of main
speakers is being used, check
the minimum impedance
requirements of your
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
speaker wires are frayed,
cut or punctured.
• Review proper operation of
your receiver/amplifier.
If there is no sound coming
from one speaker:
• Check the “Balance” control
on your receiver/amplifier.
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
receiver/amplifier.
If there is low (or no) bass
output:
• Make sure the connections
to the left and right “Speaker
Inputs” have the correct
polarity (+ and –).
If there is no sound from the
center speaker:
• Check all wires and
speaker wires are frayed,
cut or punctured.
connections between
• In Dolby Digital or DTS
modes, make sure that the
receiver/processor is
configured so that the speaker
in question is enabled.
• Turn off all electronics and
switch the speaker in question
with one of the other speakers
receiver/amplifier and
• Make sure the subwoofer
is plugged into an active
electrical outlet.
• Make sure the powered
subwoofer is plugged in, and
its Power switch ¡ is
speaker. Make sure all wires
are connected. Make sure
none of the speaker wires are
frayed, cut or punctured.
• If your receiver/processor is
set in Dolby Pro Logic mode,
make sure the center speaker
switched on to the “ ”
•
position.
• In Dolby Digital or DTS
modes, make sure your
receiver/processor is
configured so that the
subwoofer and LFE output
are enabled.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SUB150/160/180 EXPLODED VIEW
Ref#
Description
Part Number
Qty
1
2
SUB150/160/180 CABINET
FOOT – MAIN PLASTIC BODY
NOT FOR SALE
(SCS150SI) WI5447
1
4
“
(SCS160SI) 321-ABS-00008
(SCS180.6) 321-ABS-00008-0LA
(SCS150SI) WI5448
(SCS160SI/180.6) 321-ABS-00009
06-T43005
4
4
4
4
4
1
“
FOOT – RUBBER BOTTOM
“
3
4
5
6
7
FOOT SCREW T4*30L
10” WOOFER
25MF12DZB-DW02
AMPLIFIER/WOOFER SCREWS T4*20L
SUB150/160/180 AMPLIFIER
06-T4205012
NOT FOR SALE
15
1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
Test Set Up and Procedure
Equipment needed:
•
•
•
•
Function/signal generator/sweep generator
Integrated Amplifier
Multimeter
Speaker cables
General Unit Function (UUT = Unit Under Test)
1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R
on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to
the single LFE input.
2) Turn on generator; adjust to 100mV, 50 Hz.
3) Plug in UUT; turn the power switch ON. LED should switch from Red to Green. Turn LEVEL control full
clockwise (MAX)
4) LED should Green; immediate and vigorous bass response should be heard and felt from port tube
opening.
5) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable.
6) Connect one pair of speaker cables to Speaker Level input terminal (IN) on UUT. Cables should be
connected to an integrated amplifier fed by the signal generator.
7) Turn on generator and adjust so that speaker level input at the amplifier is 2.0V, 50 Hz. Turn LEVEL control
full clockwise.
8) Green LED should light; immediate and vigorous bass response should be heard and felt from the port
tube opening.
Sweep Function
1) Follow steps 6-8 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet (instructions on exploded view drawing); detach + and - wire clips.
2) Check DC resistance of woofer; it should be 3.4 ohms ±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier
fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
Mechanical/Satellite Parts List
SCS150SI
SCS160SI
SCS180.6S
Description
SUBWOOFER
Amplifier Ass’y
Not for Sale
Not for Sale
25MF12DZB-DW02
wi5448
Not for Sale
Not for Sale
25MF12DZB-DW02
321-ABS-00009
321-ABS-00008
Not for Sale
Not for Sale
25MF12DZB-DW02
321-ABS-00009
321-ABS-00008-0LA
SUB 150/SUB160/SUB180 Cabinet
10” Woofer DCR = 3.4 ohms ±10%
Rubber Foot Pad
Foot
wi5447
SATELLITES
Complete
Woofer
Tweeter
SCS150SI/SAT-1
32PF55JE-LW02
29DM15NA-FT03
SCS160SI/SAT-1
32PF55JE-LW02
29DM15NA-FT03
SCS180.6S SAT-1
32PF55JE-LW02
29DM15NA-FT05
(Front baffle w/Tweeter)
320-RUB-00025-0LA (Rear)
320-RUB-00053-0LA (Front)
244-030-05043-0VA
013-AA00-00296
Foot
wi5213-g
325-000-00151
Grille
X-over Network
Enclosure
Front baffle
Wall bracket
Support mural
xc035006
xr5138-1
244-030-00083
013-AA00-00296
306-ABS-00124
243-030-00323
372-000-00042
325-FE-00163
wi0408
wi0409
372-000-00042
325-FE-00163
CENTER CHANNEL
Complete
Woofer
Tweeter
Foot
Grille
X-over Network
Enclosure
Front baffle
SCS150SI/CENTER-1
32PF55JE-LW02
29DM15NA-FT03
wi5213-g
xc035007
xr5138-1
SCS160SI/CENTER-1
32PF55JE-LW02
29DM15NA-FT03
325-000-00151
SCS180.6S CEN-1
32PF55JE-LW02
29DM15NA-FT05
320-RUB-00053-0LA
244-030-05044-0VA
013-AA00-00296
244-030-00084
013-AA00-00296
306-ABS-00125
243-030-00323
OPTIONAL: Floor Stands for 150SAT & 160SAT satellites – FS400
Floor Stands for 180.6SAT satellites – FS1000
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
SUB150/SUB160/SUB180 Electrical parts List
Part#
Reference Designator
Description
Qty
Input/Power Amp PCB
Semiconductors
197131n4148
D102,103,104,105,143,201-208,
Diode 1N4148
20
211,212,214,215,216,301,302
D213
19915000335
19915000625
19915001605
192027c1815gr
192027c2235y
192028a1015gr
1921672n5551
1921682n5401
19006m4558d
19016tl074cn
192161tip31c
192162tip32c
19510204hgw
19700kbu606g
197101n4004
Zener 3.3V 1/2W 52mm TAP
Zener 6.2V 1/2W 52mm TAP
Zener 16V 1/2W 52mm TAP
Trans NPN 60V .15A 2SC1815GR
Trans NPN 120V 0.8A 2SC2235
Trans PNP 50V .15A 2SA1015GR
Trans NPN 160V 0.6A 2N5551
Trans PNP 150V 0.6A 2N5401
I.C. OPA 4558D Dual Op-Amp
I.C TL074CN ST Quad Op-Amp
Trans NPN 100V 3A TIP31C SGS
Trans PNP 100V 3A TIP32C SGS
LED 204HGW
1
1
1
9
1
3
2
1
1
3
1
1
1
1
2
D101
D502
Q108,109,113,201,206-208,301,302
Q111
Q101,107,112
Q114,115
Q503
U203
U201,202,301
Q501
Q502
D209
D501
Diode 4A 400V KBU606G
Diode 1N4004
D110,504
Resistors
11014103j26
11014222j26
11014432j26
11014472j26
11016102j26
11016103j26
R503,504,510
RES, 10K 1/4W ±5% CF 26mm
RES, 2.2K 1/4W ±5% CF
RES, 4.3K 1/4W ±5% CF
RES, 4.7K 1/4W ±5% CF
RES, 1K 1/6W ±5% CF
3
1
R511
R506
1
R505
1
R153,213,214,215,254
5
R128,130,149,150,209,212,216,217,
220,221,222,225-230,232,235,
240,248,260,264,305,306,308,311,
314,319
RES, 10K 1/6W ±5% CF
29
11016104j26
11016105j26
11016122j26
11016124j26
11016151j26
11016153j26
11016154j26
11016182j26
11016183j26
11016203j26
11016205j26
R122,126,231,266,307
RES, 100K 1/6W ±5% CF
RES, 1M 1/6W ±5% CF
RES, 1.2K 1/6W ±5% CF
RES, 120K 1/6W ±5% CF
RES, 150 ohms 1/6W ±5% CF
RES, 15K 1/6W ±5% CF
RES, 150K 1/6W ±5% CF
RES, 1.8K 1/6W ±5% CF
RES, 18K 1/6W ±5% CF
RES, 20K 1/6W ±5% CF
RES, 2Meg ohm 1/6W ± CF
5
1
1
1
1
2
1
1
1
1
1
R259
R265
R233
R252
R107,234
R252
R145
R262
R309
R257
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
Part#
Input/Power Amp PCB
R144
Reference Designator
Description
Qty
11016221j26
11016222j26
11016223j26
11016273j26
11016333j26
11016393j26
11016472j26
11016473j26
11016474j26
11016512j26
11016513j26
11016562j26
11016621j26
11016751j26
11016755j26
11016913j26
116161002f26
116161102f26
116162200f26
116162202f26
11020332jk3
11120102jk3
11130471jk2
11350s68j00
11012472j00
115h503a102
RES, 220 ohms 1/6W ±5% CF
RES, 2.2K 1/6W ±5% CF
RES, 22K 1/6W ±5% CF
RES, 27K 1/6W ±5% CF
RES, 33K 1/6W ±5% CF
RES, 39K 1/6W ±5% CF
RES, 4.7K 1/6W ±5% CF
RES, 47K 1/6W ±5% CF
RES, 470K 1/6W ±5% CF
RES, 5.1K 1/6W ±5% CF
RES, 51K 1/6W ±5% CF
RES, 5.6K 1/6W ±5% CF
RES, 620 ohms 1/6W ±5% CF
RES, 750 ohms 1/6W ±5% CF
RES, 7.5M 1/6W ±5% CF
RES, 91K 1/6W ±5% CF
RES, 10K 1/6W ±1% MF
RES, 11.0K 1/6W ±1% MF
RES, 220 ohms 1/6W ±1% MF
RES, 22.0K 1/6W ±1% MF
RES, 3.3K 2W ±5% 7.5mm
RES,MF 1K 2W ±5% 7.5mm
RES,MF 470 ohms 3W ±5% 10mm
RES,CEW 0.068 ohms 5W
RES, 4.7K 1/2W ±5%
1
1
6
2
1
1
3
6
2
2
1
1
1
1
1
4
2
1
1
1
1
1
2
1
2
1
R102
R238,247,255,256,263,316
R223,237
R310
R151
R200,207,258
R106,129,219,249,250,251
R127,312
R210,211
R224
R152
R160
R315
R313
R203-206
R301,303
R302
R317
R318
R134
R148
R501,502
R147
R201,202
VR201
POT Gain control (50K)
Capacitors
132103kb00
C500
CAP, MY 0.01uF 200V ±10%
1
2
1385478m63
129a154j633
1302b101k503
1302b221k503
C501,502
C221,222
C302,303,306
CAP, E 4700u 63v 20% pitch 10mm
CAP, F 0.15U 63V ±5% MSC TAP
CAP, CA 100P 50V ±10% TAP
CAP, CA 220P 50V ±10% TAP
2
3
C200,204-208,210,211,212,214,
12
220,230,249
C229
1302b470k503
1302f104z503
CAP, CA 47P 50V ±10% TAP
1
C100,107,117,122,144,232,242,244,
245,246,252,254,256,320,322
C223,224,305,317
CAP, CA 0.1U 50V +80/-20% TAP
15
132103j503
132103ja03
132104ja03
132223ja03
132273ja03
132473ja03
CAP, MY 0.01U 50V ±5% TAP
CAP, MY 0.01uf 100V ±5% TAP
CAP, MY 0.1UF 100V ±5% TAP
CAP, MY 0.022uF 100V ±5% TAP
CAP, MY 0.027UF 100V ±5% TAP
CAP, MY 0.047uF 100V ±5% TAP
4
2
4
1
1
2
C103,104
C123,218,503,504
C215
C143
C216,217
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
Part#
Reference Designator
Description
Qty
Input/Power Amp PCB
1353105m50
1353106m50
C228
CAP, E 1U 50V ±20% TAP
CAP, E 10U 50V ±20% TAP
1
C201,202,206,213,219,231,241,243,
251,253,319,321
12
1353107m10
1353107m16
1353107m35
1353225m50
1353226m16
1353226m50
1353227m16
1353476m16
C114,115
CAP, E 100U 10V ±20% TAP
CAP, E 100uF 16V ±20% TAP
CAP, E 100U 35V ±20% TAP
CAP, E 2.2U 50V ±20% TAP
CAP, E 22U 16V ±20% TAP20% TAP
CAP, E 22U 50V ±20% TAP
CAP, E 220U 16V ±20% TAP
CAP, E 47U 16V ±20% TAP
2
1
2
1
1
3
2
1
C234
C507,508
C509
C304
C225,505,506
C118,233
C318
Power Amp Class D Module part# 012-7500-00022 RECOMMENDED: REPLACE ENTIRE MODULE
Resistors
11812061001j
11812061002j
118120610r0j
11812061201j
11812062002j
11812062201j
11812062701j
11812063000j
11812063301j
11812063902j
11812064700j
11812064701j
11812064702j
11812064704j
118120647r0j
R2,11,29,30
R7,9,25
R22,23
R31-46
R26
RES, 1.00K 1206 5%
RES, 10.0K 1206 5%
RES, 10.0 ohms 1206 5%
RES, 1.20K 1206 5%
RES, 20.0K 1206 5%
RES, 2.20K 1206 5%
RES, 2.70K 1206 5%
RES, 300.0 ohms 1206 5%
RES, 3.30K 1206 5%
RES, 39.0K 1206 5%
RES, 470 ohms 1206 5%
RES, 4.70K 1206 5%
RES, 47.0K 1206 5%
RES, 4.70M 1206 5%
RES, 47.0 ohms 1206 5%
4
3
2
16
1
3
1
1
4
1
1
3
1
1
2
R6,13,16
R10
R24
R14,15,27,28
R3
R8
R1,5,12
R17
R4
R20,21
Capacitors
141c0101k50
141c0220k50
141c0561k50
141c6104m50
141c7223k50
141d7104ka0
128e106ma01
141d7104kb0
C4
CAP,CA 100pF 50V 10% 1206 NP0
CAP,CA 22pF 50V 10% 1206 SMT NPO
CAP,CA 560pF 50V 10% 1206 NPO
CAP,CA 0.1uF 50V 20% 1206 Z5U
CAP,CA 0.022uF 50V 10% 1206 X7R
CAP,NP 0.1uF 100V 10% 1210 X7
CAP,E NP 10uF 100V 20%
1
1
1
8
1
1
2
1
C5
C6
C2,3,7,8,9,10,11,15
C13
C1
C16,17
CAP,NP 0.1uF 200V 10% 1210 X7
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
Part#
Reference Designator
Description
Qty
Power Amp Class D Module part# 012-7500-00022 RECOMMENDED: REPLACE ENTIRE MODULE
Semiconductors
19016tl072dts
19209124126qs
19209139066rs
19209210376qs
19209215146rs
19703rls4148s
19915000563s
19915001203s
19915001503s
192232irf9640
192233irf640
IC1
SMD I.C. TL072CDT SGS Dual Op-Amp
TRANS, NPN 50V 0.15A 2SC2412K
TRANS, NPN 120V 0.05A 2SC3906K
TRANS, PNP 50V 0.15A 2SA1037K
TRANS, PNP 120V 0.05A 2SA1514K
Diode RLS4148
1
3
2
2
2
6
2
2
2
1
1
Q1,4,5
Q2,8
Q7,9
Q3,6
D1,2,3,4,5,6
Z1,2
ZENER 5.6V 5% PHILIPS BZX84-C5 V6
ZENER 12V 5% PHILIPS BZX84-C12
ZENER 15V 5% PHILIPS BZX84-C15
FET IRF9640 IR P-CH TO220
Z5,6
Z3,4
Q10
Q11
FET IRF640 IR N-CH TO-220
Miscellaneous
1759f40hr2
Wafer 40PIN PITCH=2.54mm HR2*40
Ferrite core LS-A6206-ST EFD-30
Inductor 35uH
12214121m4191
12214350j4180
06-t3085020
06-t31207
L1
1
1
6
1
L2
PCB TO H/S-2,PCB TO PCB/H-4
TO HSQLC1004/ID150-1
SCREW 3*8
SCREW M3*12
Misc./Mechanical
25MF12DZB-DW02 10" Woofer
1
4
4
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
WI5447
Plastic foot
Foot, rubber bottom
T501
WI5448
150r4055900
152u602015
154k31505t0
15563032i
171urwh124d
180pbr12c11s
180tms7210v
1091ttc802j0
650pd30
Power Transformer 120V/60H
POWER CORD SVT FT-2 6FT
Fuse 3.15A 250V 30mm UL/CSA
Fuse holder HTB-32I 30mm UL/CSA
RELAY, RWH-SH-124D(1600ohm)
Power Switch BR12C11S
F501
For F501
RL1
SW501
SW201
TH1
SWITCH SLIDE 6PIN MS7210V
NTC, TTC-802(JS) Thermistor
PCB HOLDER L TYPE t=1.6mm S.P.C.C
SOLDER TERMINAL M3 t=0.3
HEAT SINK
TO 104sub15000
652m3t03
TO ID150
ꢀ
PCB(104qsub150d0)
653hsqlc1004
162a040d001
176wjce1
M10
2Pin spk Wires conn Asy
U/L TERMINAL CE-1
640rpsub150
700kb800
AI REAR PANEL
PLASTIC KNOB 46077-W SOFT P.V.C.
BUSHING 4K-4 NO-BB
707ac800
REAR PANEL-1,REAR COVER-1
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
Part#
Reference Designator
Description
Qty
Misc./Mechanical
723a125
EVA (Gasket) 213*15*2.0mm
EVA (Gasket) 213*15*1.0t
EVA (Gasket) 238*15*2.0mm
EVA (Gasket) 238*15*1.0t
EVA (Gasket) 225*15*1t UL
SCREW 3*8
2
2
2
2
1
4
4
4
723a125-1
723b125
723b125-1
723j125
TO SPK WIRE
06-t30804
R/P TO H/S-2,R/P TO PCB-2
SPK-2,RCA-2
06-t31004
SCREW M3*10mm
06-t41208
TO 700rc800a
SCREW 4*12
104ds15000
104sub15000
16210060003
16210082007
16250129001
1740rca108gb
PCB 171mm*141mm FR4
168*152mm 94V-0
1
1
1
1
1
J104 TO W201 PIN4
SW TO FUSE HOLDER
W201
WIRE 60mm BLACK
WIRE RED 18AWG 80mm #1015
MULTI WIRES 120mm AWG28 WHT
PIN RCA JACK BROWNGOLD
JK201
1740rcb202vg
17420810360g
1751c07v01
1751d02v01
1751d03v01
193201815t2
1201000003
JK202
JK203
M201
M100
M500
RCA JK RCB-202V D(G) GOLD PLATE A=WHIT
SPK JK BP 8PIN SH0810360G
Wafer 7PIN PITCH=2.5mm
Wafer 2PIN PITCH=3.96mm
Wafer 3PIN PITCH=3.96mm JST-VH
CERAMIC ISOLATOR
1
1
1
1
1
2
2
For Q10,11
FB1,2
Ferrite BEA 10W AI YT-C3104-0051
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
Integrated Circuit Diagrams
OPAMP, QUAD 14P DIL TL074
U201, 202, 301
4558 / TLO72 DUAL OP AMP,
U203, IC1
MOSFET, TO220
IRF640, 9640
Q11, 10
TIP31C NPN,
TIP32C PNP,
Q501,502
1. G
2. D
3. S
TRANS, PNP, 2N5401 TAP,
TO-92,
Q503
1
2
3
TRANS, NPN, 2N5551 TAP,
Q114,115
B
C
E
TRANS, PNP, TAP,
2SA1015GR, 2SC1037K,
2SA1514K
TRANS, NPN, 2SC1815GR TAP,
2SC2235, 2SC2412K, 2SC3906
Q3,6,7,9,101,107,112
Q1,2,4,5,8,11,108,109,113,201,206=208,301,302
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SCHEMATICS
SCS150SI/SCS160SI/SCS180.6S
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
24
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SCS150SI/SCS160SI/SCS180.6S
Packaging
WIRE SET (SURROUND)
SATELLITE STYROFOAM
SCS150SI – SAL5009
SCS160SI/SCS180.6S – 431-000-00937
SCS160SI/SCS180.6S – 370-000-00081
WIRE SET (SATS & CENTER)
SCS150SI – SAL5019
SCS160SI/SCS180.6S – 370-000-00087
SUPPORT MURAL
SCS150SI – WI0409
SCS160SI/SCS180.6S – 325-FE-00163
WIRE SET (SUB IN/OUT)
SCS150SI – SAL063-1
SCS160SI/SCS180.6S – 370-000-00069
WALL BRACKET
SCS150SI – WI0408
SCS160SI/SCS180.6S – 372-000-00042
WARRANTY CARD
SCS150SI – AT5160
SCS160SI/SCS180.6S – 405-000-00258
OWNER’S MANUAL
SCS150SI – AI5139
SCS160SI – 406-000-00890
SCS180.6S – 406-000-05102
WALL BRACKET WARNING SHEET
SCS180.6S – 405-000-05021
SUBWOOFER STYROFOAM (2)
SCS150SI – WP5187
SCS160SI/SCS180.6S – 431-000-00691
OUTER CARTON
SCS150SI – WG5270
SCS160SI – 402-000-01768
SCS180.6S – 402-000-05181
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|
