Owner’s Operator and Maintenance Manual
Lynx™L-3X
DEALER: This manual MUST be given to
the user of the scooter.
USER: BEFORE using this scooter, read this
manual and save for future reference.
For more information regarding
Invacare products, parts, and services,
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
TABLE OF CONTENTS
Repair or Service Information.................................................................................................................9
Operation Information..............................................................................................................................9
Weight Training........................................................................................................................................12
Suggested Maintenance Procedures.....................................................................................................20
Adjusting the Arm Width.......................................................................................................................30
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
TABLE OF CONTENTS
Adjusting the Tiller Angle.......................................................................................................................31
Recommended Battery Type.................................................................................................................34
Transporting the Scooter.......................................................................................................................42
Installing/Removing the Safety Flag.......................................................................................................45
Installing/Removing the Rear Mounted Basket..................................................................................47
REGISTER YOUR PRODUCT
The benefits of registering include:
1. Safeguarding your investment.
2. Ensuring long-term maintenance and servicing of your product.
3. Receiving updates with product information, maintenance tips and industry news.
Register ONLINE at warranty.invacare.com
Please have your model number and purchase date available to complete your registration.
Any registration information you submit will only be used by Invacare Corporation and
protected as required by applicable laws and regulations.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL NOTES
SPECIAL NOTES
Signal words are used in this manual and apply to hazards or unsafe practices which
could result in personal injury or property damage. Refer to the table below for
definitions of the signal words.
SIGNAL WORD
MEANING
Danger indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
DANGER
Warning indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
WARNING
Caution indicates a potentially hazardous situation which, if not avoided,
may result in property damage.
CAUTION
NOTICE
THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO
CHANGE WITHOUT NOTICE.
As a distributor of powered scooters, Invacare endeavors to supply a wide variety of
powered scooters to meet many needs of the end user. However, final selection of
the type of powered scooter to be used by an individual rests solely with the user
and his/her healthcare professional capable of making such a selection.
TIE-DOWN RESTRAINTS AND SEAT RESTRAINTS
Powered scooter users should NOT be transported in vehicles of any kind while in
the powered scooter. As of this date, the Department of Transportation has not
approved any tie-down systems for transportation of a user while in a powered
scooter, in a moving vehicle of any type.
It is Invacare’s position that users of powered scooters should be transferred into
appropriate seating in vehicles for transportation and use be made of the restraints
made available by the auto industry. Invacare cannot and does not recommend any
powered scooter transportation systems.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL NOTES
ꢀ WARNING
Invacare products are specifically designed and manufactured for use in conjunction
with Invacare accessories. Accessories designed by other manufacturers have not
been tested by Invacare and are not recommended for use with Invacare products.
Scooters should be examined during maintenance for signs of corrosion (water
exposure, incontinence, etc.). Electrical components damaged by corrosion should
be replaced IMMEDIATELY.
Scooters that are used by incontinent users and/or are frequently exposed to water
may require replacement of electrical components more frequently.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
LABEL LOCATIONS
LABEL LOCATIONS
Serial
Number
Label
DO NOT operate the scooter unless the tiller is in the locked position.
DO NOT lean against or pull forward on the tiller while mounting or
dismounting the scooter. Otherwise, injury may occur.
--------------------------------------------------------------------------------------------
DO NOT lift scooter up by the front or rear shroud. Otherwise injury
or damage to the scooter may occur.
1118373 Rev A
NOTE: The battery wiring label is on
the underside of the battery box lid.
DO NOT REMOVE THIS LABEL.
WARNING
The POSITIVE (+) RED battery cable MUST connect to the
POSITIVE (+) battery terminal. The NEGATIVE (-) BLACK
battery cable MUST connect to the NEGATIVE (-) battery
terminal. DO NOT allow battery cables to contact the
opposite battery terminal. Replace cables IMMEDIATELY
if cable insulation becomes damaged. Failure to observe
these warnings may result in an electrical short with
serious personal injury and/or damage to the electrical
system. See Owner’s Manual.
P/N 1148111 REV A - 03/30/07
12 V Battery
12 V Battery
FUSE 60A
FUSE 60A
Black
Black
Black
Red
White
Red
Black
Power Module
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TYPICAL PRODUCT PARAMETERS
TYPICAL PRODUCT PARAMETERS
LYNX L-3X
OVERALL DIMENSIONS
BASE LENGTH:
BASE WIDTH:
STEP HEIGHT (Floor Pan to Ground):
SEAT HEIGHT (Floor Pan to Seat Cushion):
OVERALL HEIGHT
44 inches
21.5 inches
5 inches
16 inches
36 inches
SEAT DIMENSIONS
WIDTH:
DEPTH:
18 inches
16 inches
13.5 inches
BACK HEIGHT:
ARM DIMENSIONS
LENGTH:
HEIGHT BETWEEN SEAT AND ARMS:
WIDTH BETWEEN ARMS:
11.25 inches
7 inches
17 - 24 inches
SPEED RANGE
0 - 5 m.p.h.
WHEELS
FRONT WHEEL:
DRIVE WHEEL:
8 inches x 2 inches
9 inches x 2 inches
TURNING RADIUS:
44.7 inches
WEIGHT OF PRODUCT:
FRONT BASE SECTION:
REAR BASE SECTION:
BATTERIES:
SEAT:
BASKET:
30 lbs
43 lbs
56 lbs
28 lbs
1 lb
TOTAL WEIGHT OF PRODUCT:
MAXIMUM WEIGHT LIMITATION
158 lbs
300 lbs
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1—GENERAL GUIDELINES
SECTION 1—GENERAL GUIDELINES
ꢀ WARNING
SECTION 1 - GENERAL GUIDELINES contains important information for the safe
operation and use of this product.
Repair or Service Information
Set‐up of the Electronics Control Unit is to be performed only by a qualified technician.
The final adjustments of the controller may affect other activities of the scooter. Damage
to the equipment could occur if improperly set‐up or adjusted.
DO NOT service or adjust your powered scooter while occupied, unless otherwise noted.
Scooters should be examined during maintenance for signs of corrosion (water exposure,
incontinence, etc.). Electrical components damaged by corrosion should be replaced
IMMEDIATELY.
Scooters that are used by incontinent users and/or are frequently exposed to water may
require replacement of electrical components more frequently.
Operation Information
Invacare products are specifically designed and manufactured for use in conjunction with
Invacare accessories. Accessories designed by other manufacturers have not been tested
by Invacare and are not recommended for use with Invacare products.
Performance adjustments should only be made by professionals of the healthcare field or
persons fully conversant with this process and the driverʹs capabilities. Incorrect settings
could cause injury to the driver, bystanders and damage to the scooter and to
surrounding property.
ALWAYS wear your seat positioning strap. Inasmuch as the seat positioning strap is an
option on this scooter (you may order with or without the seat positioning strap),
Invacare strongly recommends ordering the seat positioning strap as an additional
safeguard for the scooter user. The seat positioning strap is a positioning belt only. It is not
designed for use as a safety device withstanding high stress loads such as auto or aircraft
safety belts. If signs of wear appear, belt must be replaced immediately.
Before using the scooter, verify that the motor is plugged into the harness.
DO NOT connect any medical devices such as ventilators, life support machines, etc., to
the battery. This could cause unexpected failure of the device and the powered scooter.
DO NOT operate the powered scooter until you have checked that the surroundings are
clear and that the area is safe for travel.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1—GENERAL GUIDELINES
DO NOT make sharp turns in the forward or reverse direction at excessive speed. Failure
to observe the warning can cause the scooter to tip over and may result in injury to user
and/or damage to the product.
DO NOT operate on roads, streets or highways.
DO NOT attempt to move up or down an incline with water, ice or oil film.
Avoid operating the scooter in dark or poorly lit areas.
DO NOT climb and/or go up or down ramps or traverse slopes greater than 8°.
When negotiating ramps, if the throttle control lever is released while in the forward
motion, the powered scooter will roll back approximately one foot before the brake
engages. If the throttle control lever is released while in the reverse motion, the powered
scooter will roll back approximately three feet before the brake engages.
DO NOT attempt to drive over curbs or obstacles. Doing so may cause your powered
scooter to turn over and cause bodily harm and/or damage to the scooter.
DO NOT use an escalator to move a powered scooter between floors. Serious bodily
injury may occur.
Powered scooter with batteries and seat weighs 158 lbs. Use proper lifting techniques (lift
with your legs) to avoid injury.
Before attempting to sit in or exit the powered scooter, remove the key from the ignition.
This will ensure that the power is off and the powered scooter will not drive.
DO NOT remove the key or shut off while the powered scooter is in motion.
Remove the key from the ignition while the powered scooter is not in use so as to avoid
injury and/or damage to the scooter and surrounding areas.
DO NOT attempt to lift the powered scooter by any removable (detachable) parts. Lifting
by means of any removable (detachable) parts of a powered scooter may result in injury
to the user or damage to the powered scooter.
DO NOT attempt to lift the powered scooter by its tiller, seat or shrouds.
DO NOT stand on the frame of the powered scooter.
DO NOT stand on the shroud(s) of the powered scooter.
DO NOT operate the powered scooter without the rear shroud installed, to avoid injury
and/or damage to scooter.
Before use, ensure that the front frame assembly properly engages the rear frame
assembly pins and that the release lever is locked. Otherwise, injury and/or damage may
result.
DO NOT attempt to reach objects if you have to move forward in the seat or pick them up
from the floor by reaching between your knees.
DO NOT lean over the top of the back upholstery to reach objects behind you, as this may
cause the powered scooter to tip over.
DO NOT shift your weight or sitting position toward the direction you are reaching as the
powered scooter may tip over.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1—GENERAL GUIDELINES
Determine and establish your particular safety limits by practicing bending, reaching and
transferring activities in the presence of a qualified healthcare professional before
attempting active use of the powered scooter.
For individuals with balance problems, DO NOT attempt to transfer into or out of the
powered scooter without assistance. Practice transferring activities with an assistant in
the presence of a qualified healthcare professional.
Ensure that the seat is properly locked before use. Otherwise the user may fall from the
scooter resulting in bodily harm. Attempting unsafe transfers may cause the user to fall,
resulting in serious injury.
Ensure that the seat is locked in the forward position before and during the operation of
the scooter. Otherwise, injury to the user and/or damage to the scooter may result.
Ensure that the tiller is properly adjusted before driving the scooter.
After making any tiller angle adjustment and before use, the tiller must be securely locked
into position. Otherwise the user may fall from the scooter resulting in bodily harm and/
or damage to the scooter. Gently push/pull the tiller to ensure that the tiller is securely
engaged.
DO NOT overtighten hardware attaching to the frame. This could cause damage to the
frame tubing.
ALWAYS keep hands and fingers clear of moving parts to avoid injury.
ALWAYS check hand grips for looseness before using the powered scooter. If loose and/
or worn, replace immediately.
If scooter is exposed to extreme temperature (above 100°F or below 32°F), high humidity
and/or becomes wet, prior to use, ensure handgrips DO NOT twist on scooter handles.
Otherwise, damage or injury may occur.
Avoid storing or using the scooter near open flame or combustible products. Serious
injury or damage to property may result.
Never leave an unoccupied scooter on an incline.
ALWAYS use anti‐tippers. When outdoors on wet, soft ground or on gravel surfaces,
anti‐tippers may not provide the same level of protection against tip over. Extra caution
MUST be observed when traversing such surfaces.
Electrical
Check to ensure that all electrical connections are secure at all times.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1—GENERAL GUIDELINES
Grounding Instructions
DO NOT, under any circumstances, cut or remove the round grounding prong from any
plug used with or for Invacare products. Some devices are equipped with three‐prong
(grounding) plugs for protection against possible shock hazards. Where a two‐prong wall
receptacle is encountered, it is the personal responsibility and obligation of the customer
to contact a qualified electrician and have the two‐prong receptacle replaced with a
properly grounded three‐prong wall receptacle in accordance with the National Electrical
Code. If you must use an extension cord, use ONLY a three‐wire extension cord having
the same or higher electrical rating as the device being connected. In addition, Invacare
has placed RED/ORANGE warning tags on some equipment. DO NOT remove these tags.
Batteries
The warranty and performance specifications contained in this manual are based on the
use of deep cycle gel cell batteries. Invacare strongly recommends their use as the power
source for this unit.
Carefully read battery/battery charger information prior to installing, servicing or
operating your powered scooter.
Rain Test
Invacare has tested its powered scooters in accordance with ISO 7176 “Rain Test”. This
provides the end user or his/her attendant sufficient time to remove his/her power
powered scooter from a rain storm and retain powered scooter operation.
DO NOT leave the powered scooter in a rain storm of any kind.
DO NOT use the powered scooter in a shower.
DO NOT leave the powered scooter in a damp area for any length of time.
Direct exposure to rain or dampness will cause the scooter to malfunction electrically and
mechanically; may cause the powered scooter to prematurely rust.
Check to ensure that all electrical connections are secure at all times.
Weight Training
Invacare does not recommend the use of its powered scooters as a weight training
apparatus. Invacare powered scooters have not been designed or tested as a seat for any
kind of weight training. If occupant uses said powered scooter as a weight training
apparatus, Invacare shall not be liable for bodily injury and the warranty is void.
Weight Limitation
The weight limitation is 300 lbs.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2—EMI INFORMATION
SECTION 2—EMI INFORMATION
ꢀ WARNING
CAUTION: IT IS VERY IMPORTANT THAT YOU READ THIS INFORMATION
REGARDING THE POSSIBLE EFFECTS OF ELECTROMAGNETIC
INTERFERENCE ON YOUR POWERED WHEELCHAIR.
Electromagnetic Interference (EMI) From Radio Wave Sources
Powered wheelchairs and motorized scooters (in this text, both will be referred to
as powered wheelchairs) may be susceptible to electromagnetic interference (EMI),
which is interfering electromagnetic energy (EM) emitted from sources such as
radio stations, TV stations, amateur radio (HAM) transmitters, two way radios, and
cellular phones. The interference (from radio wave sources) can cause the powered
wheelchair to release its brakes, move by itself, or move in unintended directions. It
can also permanently damage the powered wheelchair's control system. The
intensity of the interfering EM energy can be measured in volts per meter (V/m).
Each powered wheelchair can resist EMI up to a certain intensity. This is called its
"immunity level." The higher the immunity level, the greater the protection. At this
time, current technology is capable of achieving at least a 20 V/m immunity level,
which would provide useful protection from the more common sources of radiated
EMI.
There are a number of sources of relatively intense electromagnetic fields in the
everyday environment. Some of these sources are obvious and easy to avoid.
Others are not apparent and exposure is unavoidable. However, we believe that by
following the warnings listed below, your risk to EMI will be minimized.
The sources of radiated EMI can be broadly classified into three types:
1) Hand-held Portable transceivers (transmitters-receivers with the antenna
mounted directly on the transmitting unit. Examples include: citizens band (CB)
radios, "walkie talkie", security, fire and police transceivers, cellular telephones,
and other personal communication devices).
NOTE: Some cellular telephones and similar devices transmit signals while they are ON,
even when not being used.
2) Medium-range mobile transceivers, such as those used in police cars, fire trucks,
ambulances and taxis. These usually have the antenna mounted on the outside of
the vehicle; and
3) Long-range transmitters and transceivers, such as commercial broadcast
transmitters (radio and TV broadcast antenna towers) and amateur (HAM)
radios.
NOTE: Other types of hand-held devices, such as cordless phones, laptop computers,
AM/FM radios, TV sets, CD players, cassette players, and small appliances, such as
electric shavers and hair dryers, so far as we know, are not likely to cause EMI problems
to your powered wheelchair.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2—EMI INFORMATION
ꢀ WARNING
Powered Wheelchair Electromagnetic Interference (EMI)
Because EM energy rapidly becomes more intense as one moves closer to the
transmitting antenna (source), the EM fields from hand-held radio wave sources
(transceivers) are of special concern. It is possible to unintentionally bring high
levels of EM energy very close to the powered wheelchair's control system while
using these devices. This can affect powered wheelchair movement and braking.
Therefore, the warnings listed below are recommended to prevent possible
interference with the control system of the powered wheelchair.
Electromagnetic interference (EMI) from sources such as radio and TV stations,
amateur radio (HAM) transmitters, two-way radios, and cellular phones can affect
powered wheelchairs and motorized scooters.
FOLLOWING THE WARNINGS LISTED BELOW SHOULD REDUCE THE
CHANCE OF UNINTENDED BRAKE RELEASE OR POWERED WHEELCHAIR
MOVEMENT WHICH COULD RESULT IN SERIOUS INJURY.
1) Do not operate hand-held transceivers (transmitters receivers), such as citizens
band (CB) radios, or turn ON personal communication devices, such as cellular
phones, while the powered wheelchair is turned ON;
2) Be aware of nearby transmitters, such as radio or TV stations, and try to avoid
coming close to them;
3) If unintended movement or brake release occurs, turn the powered wheelchair
OFF as soon as it is safe;
4) Be aware that adding accessories or components, or modifying the powered
wheelchair, may make it more susceptible to EMI (NOTE: There is no easy way
to evaluate their effect on the overall immunity of the powered wheelchair); and
5) Report all incidents of unintended movement or brake release to the powered
wheelchair manufacturer, and note whether there is a source of EMI nearby.
Important Information
1) 20 volts per meter (V/m) is a generally achievable and useful immunity level
against EMI (as of May 1994) (the higher the level, the greater the protection);
2) This device has been tested to a radiated immunity level of 20 volts per meter.
3) The immunity level of the product is unknown.
Modification of any kind to the electronics of this scooter as manufactured by
Invacare may adversely affect the EMI immunity levels.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3—SAFETY/HANDLING OF POWERED SCOOTERS
SECTION 3—SAFETY/HANDLING OF
POWERED SCOOTERS
“Safety and Handling” of the powered scooter requires the close attention of the user.
This manual points out the most common procedures and techniques involved in the safe
operation and maintenance. It is important to practice and master these safe techniques
until you are comfortable in maneuvering the powered scooter.
Use this information only as a “basic” guide. The techniques that are discussed have been
used successfully by many. Individual users often develop skills to deal with daily living
activities that may differ from those described in this manual. Invacare recognizes and
encourages each individual to try what works best for him/her in overcoming obstacles
that they may encounter; however, all warnings and cautions given in this manual MUST
be followed. Techniques in this manual are a starting point for the new powered scooter
user with “safety” as the most important consideration for all.
Stability and Balance
ꢀ WARNING
DO NOT make sharp turns in the forward or reverse direction at excessive speed.
Failure to observe the warning can cause the scooter to tip over and may result in
injury to user and/ or damage to the product.
ALWAYS wear your seat positioning strap. Inasmuch as the seat positioning strap is
an option on this scooter (you may order with or without the seat positioning
strap), Invacare strongly recommends ordering the seat positioning strap as an
additional safeguard for the scooter user. The seat positioning strap is a positioning
belt only. It is not designed for use as a safety device withstanding high stress loads
such as auto or aircraft safety belts. If signs of wear appear, belt MUST be replaced
immediately.
DO NOT attempt to reach objects if you have to move forward in the seat or pick
them up from the floor by reaching down between your knees.
Be aware that carrying heavy objects on your lap while occupying the scooter may
adversely affect the stability of the scooter, resulting in serious bodily injury to the
user, damage to the scooter and surrounding property.
This scooter has been designed to accommodate one individual. If more than one
individual occupies the scooter this may adversely affect the stability of the scooter,
resulting in serious bodily injury to the user and passenger and damage to the
scooter and surrounding property.
To assure stability and proper operation of your powered scooter, you MUST, at all times,
maintain proper balance. Your powered scooter has been designed to remain upright and
stable during normal daily activities.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3—SAFETY/HANDLING OF POWERED SCOOTERS
Many activities require the scooter owner to reach, bend and transfer in and out of the
powered scooter. These movements cause a change to the normal balance, the center of
gravity, and the weight distribution of the powered scooter. To determine and establish
your particular safety limits, practice bending, reaching and transferring activities in
several combinations in the presence of a qualified healthcare professional before
attempting active use of the scooter. Proper positioning is essential for your safety.
Stairways
ꢀ WARNING
DO NOT attempt to move an occupied powered scooter between floors using a
stairway. Use an elevator to move an occupied powered scooter between floors.
If moving a powered scooter between floors by means of a stairway, the occupant
MUST be removed and transported independently of the powered scooter.
Extreme caution is advised when moving an unoccupied powered scooter up or
down the stairs. Invacare recommends disassembling the scooter and transporting
the components independently up or down the stairs. ONLY use secure, non-
detachable parts on each component for hand-hold supports.
DO NOT attempt to lift a powered scooter by any removable (detachable) parts.
Lifting by means of removable (detachable) parts may result in injury to the user or
assistants or damage to the powered scooter.
Escalators
ꢀ WARNING
DO NOT use an escalator to move a powered scooter between floors. Serious
bodily injury may occur.
Powered scooter without the batteries can weigh between 80 and 89 lbs. Use
proper lifting techniques (lift with your legs) to avoid injury.
Follow this procedure for moving the powered scooter between floors when an elevator
is not available:
1. Remove the occupant from the powered scooter.
3. Carefully move the powered scooter components up or down the stairway.
4. Once all the components of the scooter are transported to the desired location
reassemble the scooter. Refer to Transporting the Scooter on page 42.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4—SAFETY INSPECTION
SECTION 4—SAFETY INSPECTION
NOTE: Every six months take your powered scooter to a qualified technician for a thorough
inspection and servicing. Regular cleaning will reveal loose or worn parts and enhance the smooth
operation of your powered scooter. To operate properly and safely, your powered scooter must be
cared for just like any other vehicle. Routine maintenance will extend the life and efficiency of your
powered scooter.
ꢀ WARNING
Before performing any maintenance, adjustment or service, turn power Off and
remove key from ignition.
CAUTION
As with any vehicle, the wheels and tires should be checked periodically for cracks
and wear, and should be replaced.
Safety Inspection Checklists
Initial adjustments should be made to suit your personal body structure needs and
preference. Thereafter follow these maintenance procedures:
Inspect/Adjust Initially
❑ Ensure powered scooter drives straight (no excessive drag or pull to one side).
❑ Check frame for damage and corrosion.
❑ Ensure that the brake release lever is easy to engage/disengage.
❑ Ensure that tiller adjustment mechanism engages and disengages properly and
securely.
❑ Ensure that the scooter stops completely when throttle is released (i.e., does not
continue to roll as if the throttle is activated).
❑ Clean upholstery and armrests.
❑ Ensure armrest pad sits flush against arm tube.
❑ Inspect the seat upholstery for rips and tears.
❑ Inspect seat swivel for release and engagement (seat locks into the determined swivel
positions).
❑ Inspect for excessive side movement or binding when the drive wheels are raised or
turned.
❑ Inspect front wheel/fork assembly for proper tension by spinning the wheel. The front
wheel should come to a gradual stop.
❑ Check the front fork for damage or corrosion.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4—SAFETY INSPECTION
❑ Tighten locknut if the front wheel wobbles noticeably or loosen locknut if the wheel
binds to a stop.
❑ Ensure that wheel bearings are clean and free of moisture.
❑ Ensure that the bolts and fasteners on the caster assemblies are tight.
❑ Inspect tires for flat spots and wear.
❑ Clean molded body shrouds.
❑ Check that all labels are present and legible.
Inspect/Adjust Weekly
❑ Ensure that tiller adjustment mechanism engages and disengages properly and
securely.
❑ Ensure that the scooter stops completely when throttle is released (i.e., does not
continue to roll as if the throttle is activated).
❑ Inspect tires for flat spots and wear.
Inspect/Adjust Monthly
❑ Check brake for binding or interference with travel.
❑ Inspect front wheel/fork assembly for proper tension by spinning the wheel. The front
wheel should come to a gradual stop.
❑ Tighten locknut if the front wheel wobbles noticeably or loosen locknut if the wheel
binds to a stop.
❑ Inspect seat swivel for release and engagement (seat locks into the determined swivel
positions).
❑ Ensure that the bolts and fasteners on the caster assemblies are tight.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4—SAFETY INSPECTION
Inspect/Adjust Periodically
❑ Ensure that the powered scooter drives straight (no excessive drag or pull to one side).
❑ Check frame for damage and corrosion.
❑ Ensure that the brake release lever is easy to engage/disengage.
❑ Inspect for no excessive side movement or binding when the drive wheels are raised
or turned.
❑ Check front fork for damage or corrosion.
❑ Ensure wheel bearings are clean and free of moisture.
❑ Clean upholstery and armrests.
❑ Inspect the seat upholstery for rips and tears.
❑ Ensure armrest pad sits flush against arm tube.
❑ Check that all labels are present and legible.
❑ Inspect electrical components for signs of corrosion. Replace if corroded or damaged.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5—MAINTENANCE AND TROUBLESHOOTING
SECTION 5—MAINTENANCE AND
TROUBLESHOOTING
ꢀ WARNING
After any adjustments, repair or service and before use, make sure that all attaching
hardware is tightened securely - otherwise, injury or damage may occur.
Before performing any maintenance, adjustment or service, turn power Off and
remove key from ignition.
DO NOT overtighten hardware attaching to the frame. This could cause damage to
the frame.
When storing scooter for prolonged periods of time, remove batteries. Refer to
Removing/Installing the Batteries on page 35. After reinstallation, always recharge
Use care in storage. DO NOT allow any metallic objects to contact the exposed
terminals.
Suggested Maintenance Procedures
1. Before using the powered scooter, make sure all nuts and bolts are tight. Check any
parts for damage or wear and replace. Check all parts for proper adjustment.
2. Ensure that batteries are properly maintained and charged as required.
3. The wheels and tires should be checked periodically for cracks and wear, and should
be replaced by a qualified technician.
4. Regularly check for loose nuts and/or bolts in the front and drive wheels. If loose, have
them adjusted by a qualified technician.
5. Clean dirt, dust and grease from exposed components.
6. Periodically have the bearings of the front wheel checked to make sure they are clean
and free from moisture.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5—MAINTENANCE AND TROUBLESHOOTING
Troubleshooting
SYMPTOM
PROBABLE CAUSE
SOLUTION
Limited Driving Distance.
Battery not charged long enough.
Charge batteries overnight or ensure eight
hours of charge between use.
Batteries weak, won’t hold
charge.
Replace batteries. Refer to Removing/
Batteries not Charging.
Charger not working.
Replace charger. Contact Dealer or a
qualified technician.
Battery connections loose.
Check all connections. Secure connections.
No current at wall outlet.
Bad connection on charger,
charger cable, plug or internal
wiring problem.
Switch another wall outlet.
Replace charger or internal repairs
required. Contact Dealer or a qualified
technician.
Batteries draw excessive
current when charging.
Battery failure.
Replace batteries. Refer to Removing/
Battery indicator shows the Charger not working.
charge level is low too
soon after being recharged.
Weak batteries.
Have charger checked. Service or replace
the charger. Contact Dealer or a qualified
technician.
Replace batteries. Refer to Removing/
Scooter will not drive.
Brake release lever disengaged.
Engage brake release lever. Refer to
Batteries require charging.
Charge batteries. Refer to Charging the
Key not fully plugged in.
Charger plugged in.
Ensure key is inserted fully into keyswitch.
Unplug charger from scooter.
Fuse blown in battery box.
Contact Dealer or qualified technician.
Soft stop engaged. If key is turned With key in the off position, wait for 30
off while driving, the scooter
holds power for 1.5 seconds
slowly decelerating to a stop.
seconds and turn key to the on position.
Battery connections loose.
Check all connections. Secure connections.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5—MAINTENANCE AND TROUBLESHOOTING
Service Indicator Error Codes
NUMBER OF FLASHES
PROBLEM
SOLUTION
1
Batteries need charging.
Recharge the batteries. Refer to
2
3
Low battery voltage.
Recharge the batteries before using.
Battery voltage too high.
Check battery condition and
connections. Contact a qualified
technician to check your battery
charger.
4
5
Motor current error.
Scooter has drawn too much
current. Verify there are no objects
blocking the tires.
Brake release lever is disengaged.
Engage the brake release lever.
Turn the key off, then on to reset. If
this does not correct the problem,
contact a qualified technician.
6
Throttle control lever not in neutral. Turn the scooter power off, verify
the throttle control lever is in the
center position, and turn the power
back on. If this does not correct the
problem, contact a qualified
technician.
7
Throttle control lever malfunction
or speed pot error.
Contact a qualified technician.
8
9
Motor problems.
Contact a qualified technician.
Contact a qualified technician.
Other internal errors.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6—OPERATION OF THE POWERED SCOOTER
SECTION 6—OPERATION OF THE
POWERED SCOOTER
Control Panel
NOTE: For the following information, refer to FIGURE 6.1 on page 24.
1. Speed Control Knob ‐ The speed control knob is located on the right side of the control
panel. The Turtle icon represents the slowest speed and the Rabbit icon represents the
fastest speed.
2. Battery Charge Display ‐ The battery charge display is located at the top center of the
control panel. When the scooter is turned on, the needle on the battery charge display
will move to the right to indicate the amount of battery charge. The amount of battery
charge is indicated by the colors on the display. If the charge is full, the needle will be
to the right, in the GREEN area. As the battery charge decreases, the needle moves,
from right to left. When the needle is in the YELLOW area, the batteries are draining
and should be charged soon. When the needle is to the far left in the RED area, charge
the batteries immediately. If the needle does not move when the scooter is turned on,
the batteries should be charged as soon as possible.
ꢀ WARNING
When negotiating ramps, if the throttle control lever is released while in forward
motion, the powered scooter will roll back approximately one foot before brake
engages. If the throttle control lever is released while in reverse motion the
powered scooter will roll back approximately three feet before brake engages.
3. Key ‐ The key is just below the control panel. Turn the key:
• To the Left ‐ Turn the scooter off.
• To the Right ‐ Turn the scooter on.
4. Horn Button ‐ The horn button is located on left side of the control panel.
5. Throttle Control Lever ‐ The throttle control lever is located in front of the handles on
the tiller assembly.
6. Service Indicator ‐ The service indicator will flash if there is a problem with the
scooter. The number of flashes indicates the type of error. Refer to Service Indicator
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6—OPERATION OF THE POWERED SCOOTER
Horn Button
Battery Charge Display
Key
Service Indicator
Speed Control Knob
Throttle Control Lever
Operating the Scooter
ꢀ WARNING
After any adjustments, repair or service and before use, make sure that all attaching
hardware is tightened securely - otherwise injury or damage may result.
DO NOT make sharp turns in the forward or reverse direction at excessive speed.
Failure to observe the warning can cause the scooter to tip over and may result in
injury to user and/ or damage to the product.
To determine and establish your particular safety limits, practice bending, reaching
and transferring activities in several combinations in the presence of a qualified
healthcare professional before attempting active use of the powered scooter.
Ensure seat is properly locked before attempting transfer into or out of the
powered scooter. Attempting unsafe transfers may cause a fall from the powered
scooter resulting in bodily injury.
For individuals with balance problems, practice transferring activities with an
assistant in the presence of a qualified healthcare professional. DO NOT attempt to
transfer into or out of the powered scooter without assistance.
4. Transferring to and from the seat can be accomplished in one of two ways:
• Flipping up the armrest makes entering/exiting easier.
5. Once you have transferred into the seat, rotate seat to the forward position and flip
arms down.
7. Adjust speed control knob to the appropriate setting.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6—OPERATION OF THE POWERED SCOOTER
NOTE: For driving indoors or on uneven terrain, a slower speed is recommended. For soft terrain
or steep inclines (no greater than 8°), a faster speed may be necessary.
8. Insert the key into the ignition and turn it to the on position.
ꢀ WARNING
ALWAYS depress the throttle control lever gradually. This will ensure smooth safe
starts.
NOTE: Throttle control levers operate such that moving one will also move the opposite side
throttle control lever.
9. To operate the scooter, depress the throttle control lever in the following manner:
• To Move Forward ‐ Push the right side throttle control lever (away from the user)
or pull the left side throttle control lever towards the user).
• To Move in Reverse ‐ Push the left side throttle control lever (away from the user)
or pull the right side throttle control lever (towards the user).
• To Stop ‐ Release the throttle control lever and the powered scooter will quickly
slow down and the brake will engage.
NOTE: To equip the scooter for left hand operation, contact a qualified technician.
The powered scooter is equipped with a ʺproportionalʺ control meaning that the farther
you depress the throttle control lever, the faster the powered scooter travels. With a
proportional control, you can drive as slowly in the high speed setting as you can in the
low speed setting. Your top speed, however, is limited by the setting of the speed‐control
knob. For safety reasons, reverse speed is limited to approximately 50% of forward speed.
When first learning to drive, adjust speed control knob for a slow speed and try to drive
the powered scooter as slowly as possible by depressing the throttle control lever only
slightly. This exercise will help you learn to utilize the full potential of the proportional
control and allow you to start and stop smoothly.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6—OPERATION OF THE POWERED SCOOTER
Engaging/Disengaging the Brake Release Lever
ꢀ WARNING
Ensure that the brake-release lever is in the engaged position before driving. There
should be an audible "click" when stopping and starting the scooter.
NOTE: For the following procedure, refer to FIGURE 6.2.
The brake release lever manually engages and disengages the brake. The brake release
lever is located under the seat on the right side.
The brake must be engaged in normal driving conditions. Activation of the throttle
control lever automatically releases the brake so that the powered scooter can drive.
Releasing the throttle control lever automatically engages the brake to prevent the
powered scooter from rolling on its own.
When the brake release lever is disengaged and the key is removed, the powered scooter
can be pushed. The powered scooter cannot be driven with the brake in the disengaged
position.
1. To Engage the Brake Release Lever (Drive) ‐ Push the brake release lever down.
2. To Disengage the Brake Release Lever (Push) ‐ Pull the brake release lever up.
Pull Up to
Disengage
(Push)
Brake Release
Lever
Push Down to
Engage
(Drive)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7—SEAT AND ARMS
SECTION 7—SEAT AND ARMS
ꢀ WARNING
After any adjustments, repair or service and before use, make sure that all attaching
hardware is tightened securely - otherwise injury or damage may result.
Before performing any maintenance, adjustment or service, turn power off and
remove key from ignition.
Removing/Installing the Seat
ꢀ WARNING
Before use, ensure that the seat is in the locked position. The seat lever MUST be
pulled up to the 90° position to allow the seat to drop into the locked position. Oth-
erwise, a fall from the scooter could occur causing bodily injury and/or damage to
the scooter.
NOTE: For this procedure, refer to FIGURE 7.1.
NOTE: Seat lock lever located on left side of seat.
Removing
1. Fold down seat back.
2. Pull up the seat lock lever.
3. Lift the seat assembly up and away from the seat post.
Installing
1. Lower the seat assembly onto the seat post.
2. Pull the seat lock lever up to allow the seat to drop into the locked position.
3. Lift up on seat assembly to ensure the seat is secure.
Seat
Assembly
Seat Post
Seat Lock Lever
27
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7—SEAT AND ARMS
Adjusting Seat Height
NOTE: For this procedure, refer to FIGURE 7.2.
2. Remove the mounting bolt, two curved washers and lock nut securing the seat post to
the frame tube.
3. Align the frame tube mounting hole with one of three seat post mounting holes to
achieve desired seat height.
4. Using the mounting bolt, two curved washers and locknut, secure the seat post to the
frame tube.
Seat Post
Frame Tube
Curved
Washers
Curved
Washers
Mounting Bolt
Locknut
28
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7—SEAT AND ARMS
Adjusting 90° Seat Swivel
ꢀ WARNING
Ensure that seat is locked into the forward position before and during operation of
the scooter. Otherwise, injury to the user and/or damage to the scooter may result.
CAUTION
Use the seat swivel option with caution when accessories are installed (such as
safety flag, crutch/cane holder, etc.). Otherwise, damage to the scooter or property
may occur.
NOTE: For this procedure, refer to FIGURE 7.3.
1. Pull up the seat lock lever to unlock the seat.
2. Rotate the seat to the desired position.
3. Release the seat lock lever to lock the seat in the desired position.
NOTE: Ensure that the seat is locked in the forward facing position before operating the scooter.
Adjusting the Seat Slide
NOTE: For this procedure, refer to FIGURE 7.3
1. Lift the seat slide lever located on the right side of the seat.
2. Slide the seat forward or back to the desired position.
3. Release the seat slide lever and allow the seat to lock into position.
Seat
Slide Lock Lever
Seat Lock Lever
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7—SEAT AND ARMS
Adjusting the Arm Width
NOTE: For this procedure, refer to FIGURE 7.4.
NOTE: When installing the arms during set up, the four mounting screws are installed on the seat
hinge for shipping purposes.
1. Loosen the knob securing the arm tube to the seat frame.
2. Push the arm in or out to the desired position.
Arm
Arm
Arm Tube
Arm Tube
Knob
Knob
Seat Frame
Replacing Armrest Pads
Arm Pad
NOTE: For this procedure, refer to
FIGURE 7.5.
1. Remove the one mounting screw that
Mounting Screw
secure the armrest pad to arm.
2. Remove the old armrest pad.
3. Install new armrest pad and securely
Arm
tighten with existing mounting screw.
4. If necessary, repeat STEPS 1‐3 to
replace the other armrest pad.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8—TILLER ADJUSTMENT
SECTION 8—TILLER ADJUSTMENT
Adjusting the Tiller Angle
ꢀ WARNING
Before performing any maintenance, adjustment or service, turn power Off and
remove key from ignition.
Ensure that tiller is properly adjusted before driving the scooter.
After making any tiller angle adjustments and before use, the tiller MUST be
securely locked into position. Otherwise, a fall from the scooter could occur causing
bodily injury and/or damage to the scooter. Gently, push/pull against tiller to ensure
that the tiller is securely engaged into the adjustment plate.
NOTE: For this procedure, refer to FIGURE 8.1.
NOTE: The powered scooters feature an adjustable tiller. The tiller locks into one of three positions.
NOTE: The tiller can also be folded down and locked into this position for transportation and
storage.
1. Pull out the tiller adjustment lever until the pin disengages from the mounting hole.
2. Move the tiller to the desired position.
3. Release the tiller adjustment lever to lock the pin into the desired mounting hole.
4. Gently push/pull against tiller to ensure that the tiller is securely locked.
Tiller Assembly
Pin
Mounting
Hole
Tiller
Adjustment
Lever
31
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 9—WHEELS AND CASTERS
SECTION 9—WHEELS AND CASTERS
ꢀ WARNING
After any adjustments, repair or service and before use, make sure that all attaching
hardware is tightened securely - otherwise injury or damage may result.
Before performing any maintenance, adjustment or service, turn power Off and
remove key from ignition.
Removing/Installing the Drive Wheels
NOTE: For this procedure, refer to FIGURE 9.1 on page 33.
Removing
1. Turn power off and remove the key from the ignition.
3. Place the rear frame assembly (not shown) up on blocks so that the drive wheels are
off the ground.
4. Remove the cap, nut, large washer and small washer that secure the drive wheel to the
drive shaft.
5. Remove the existing drive wheel assembly from the drive shaft.
NOTE: Use a wheel puller if necessary to remove the wheel from the drive shaft.
6. Remove keystock from drive shaft. Set aside.
7. If necessary, repeat STEPS 1‐6 to remove other drive wheel.
Installing
NOTE: The keystock in the drive shaft MUST lineup with the cutout in the wheel hub.
NOTE: If necessary, use a rubber hammer to gently tap drive wheel completely into position on the
drive shaft.
2. Install the drive wheel onto the drive shaft.
3. Secure wheel to drive shaft using the large washer, small washer and nut. Securely
tighten.
4. Install the cap onto the nut.
5. Repeat STEPS 1‐4 to install the other drive wheel.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 9—WHEELS AND CASTERS
Keystock
NOTE: Scooter not shown.
Drive Wheel
Drive
Shaft
Small Washer
Nut
Large
Washer
Cap
Removing/Installing the Front Wheel
NOTE: For this procedure, refer to FIGURE 9.2.
NOTE: Take note of position and orientation of wheel and mounting hardware before removing.
Removing
1. Turn power off and remove the key from the ignition.
2. Place the front of the powered scooter up on blocks so that the front wheel is off the
ground.
3. Remove the mounting screw, locknut, two spacers and washer that secure the front
wheel to the fork.
4. Remove the front wheel from the fork.
Fork
ForkMounting
Hole
Installing
Fork
Mounting
Hole
Locknut
1. Align the front wheel with the fork
mounting holes.
2. Using the mounting screw, locknut,
two spacers and washer, secure the
front wheel to the fork.
Front
Wheel
Washer
3. Securely tighten the front wheel
mounting hardware.
Mounting
Screw
Spacer
Spacer
33
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10—BATTERIES
SECTION 10—BATTERIES
ꢀ WARNING
Before performing any maintenance adjustment or service, turn power off and
remove key from ignition.
NEVER allow any of your tools and/or battery cables to contact both battery
terminals at the same time. An electrical short may occur and serious personal
injury or damage may occur.
The use of rubber gloves is recommended when working with batteries.
DO NOT tip the batteries. Keep the batteries in an upright position.
Invacare strongly recommends that battery installation and battery replacement
always be done by a qualified technician.
All battery terminals caps (two on the left battery and two on the right battery)
MUST be installed prior to use.
CAUTION
When connecting the battery cables to the batteries, the battery cables MUST be
damage to the battery may result.
NOTE: If there is battery acid in the bottom of the battery box or on the sides of the batteries, apply
baking soda to these areas to neutralize the battery acid. Before reinstalling the existing or new
batteries, clean the baking soda from the battery tray or batteries being sure to avoid contact with
skin and eyes. Determine source of contamination. Never install/reinstall a battery with a cracked
or otherwise damaged case.
Recommended Battery Type
ꢀ WARNING
The warranty and performance specifications contained in this manual are based on
the use of deep cycle gel cell batteries. Invacare strongly recommends their use as
the power source for this unit.
CAUTION
Failure to use the correct battery size and/or voltage may cause damage to the
powered scooter and give unsatisfactory performance.
NOTE: For this procedure, refer to FIGURE 10.1 on page 35.
The Lynx L‐3X powered scooters are designed to use two 12 volt, 36‐Amp‐hour (36 AH)
batteries.
NOTE: Recommended battery type is spill proof and requires no maintenance except routine
charging.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10—BATTERIES
NOTE: Charge batteries daily. DO NOT allow batteries to completely discharge.
NOTE: Invacare recommends that both batteries be replaced if one battery is defective.
12 Volt, 36 Amp-Hour
(36 AH) Battery
Removing/Installing the Batteries
NOTE: For this procedure, refer to FIGURE 10.2 on page 36.
Removing
1. Place the powered scooter in a well ventilated area.
CAUTION
Work should be performed in an area without risking damage to carpeting or floor
covering.
2. Turn power off and remove the key from the ignition.
4. Lifting up to release the hook and loop strips, remove the rear shroud from the scooter.
5. Disconnect the two GRAY battery connectors from the wiring harness connectors.
6. Perform the following to remove a battery from the battery tray:
A. Pull the hook and loop fastening battery strap apart.
B. Lift the battery from the battery tray.
7. Repeat STEP 6 to remove the remaining battery.
Installing
1. Place the powered scooter in a well ventilated area where work can be performed
without risking damage to carpeting or floor covering.
2. Turn power off and remove the key from the ignition.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10—BATTERIES
5. Lifting up to release the hook and loop strips, remove the rear shroud from the scooter.
6. Perform the following to install a battery from the battery tray:
A. With the battery terminals facing towards the center of the scooter, position the
battery onto the battery tray.
B. Position the hook and loop fastening battery strap around the battery and to secure
the battery to the battery tray.
7. Repeat STEP 6 to install the remaining battery into the battery tray.
8. Connect the two GRAY battery connectors to the wiring harness connectors.
9. Align tabs on the rear shroud with the slots (not shown in figure) in the front shroud.
10. Place rear shroud on the frame and press down slightly.
11. Reinstall the seat. Refer to Removing/Installing the Seat on page 27.
NOTE: New batteries MUST be fully charged before using, otherwise the life of the batteries will
be reduced.
Battery
Connectors
Strap
Batteries
Battery Wiring Harness Connectors
36
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10—BATTERIES
Connecting/Disconnecting the Battery Cables
ꢀ WARNING
Battery terminal configuration shown below MUST be used. Batteries that have the
reversed terminal configuration MUST NOT be used - otherwise serious injury or
damage may occur.
DO NOT USE
NEGATIVE (-)
Battery Terminal
NEGATIVE
(-) Battery
Terminal
POSITIVE
(+) Battery
Terminal
POSITIVE (+)
Battery Terminal
NEVER allow any of your tools and/or battery cable(s) to contact BOTH battery
terminal(s)/post(s) at the same time. An electrical short may occur and serious
personal injury or damage may occur.
The use of rubber gloves and chemical goggles and face shield is recommended
when working with batteries.
Do not remove fuse or mounting hardware from the POSITIVE (+) RED battery
cable/mounting screw.
NEVER defeat or bypass any fuse. ONLY replace with a fuse of the same rating.
NOTE: For this procedure, refer to FIGURE 10.3 on page 39.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10—BATTERIES
Connecting
1. Install battery terminal cap(s) onto battery cable(s) as follows:
A. RED battery terminal cap onto RED battery cable.
B. GREY battery terminal cap onto BLACK battery cable.
ꢀ WARNING
When connecting the battery cables to the batteries, the battery cables MUST be
damage to the battery cable may result when installing battery terminal caps.
2. Connect battery cables to battery terminals:
A. NEGATIVE (‐) BLACK battery cable to NEGATIVE (‐) battery terminal/post.
B. POSITIVE (+) RED battery cable to POSITIVE (+) battery terminal/post.
3. Secure the battery cables ring terminal to the battery terminals, BLACK to NEGATIVE
(‐) and red to POSITIVE (+), with the provided mounting bolt and locknut. Securely
tighten.
4. Verify all battery cables ring terminal are correctly installed and securely tightened.
5. Slide terminal caps down battery cables and onto battery clamps.
NOTE: New Battery(ies) MUST be fully charged before using, otherwise the life of the battery(ies)
will be reduced.
8. Install the rear shroud. Refer to Removing/Installing the Rear Shroud on page 44.
9. Install the seat. Refer to Removing/Installing the Seat on page 34.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10—BATTERIES
Disconnecting
ꢀ WARNING
The use of rubber gloves and chemical goggles and face shield is recommended
when working with batteries.
NEVER allow any of your tools and/or battery cable(s) to contact both battery
terminal(s)/post(s) at the same time. An electrical short may occur and serious
personal injury or damage may occur.
2. Slide terminal caps up on the battery cables.
3. Disconnect the battery cables from the battery terminals by remove the mounting
bolts and locknuts securing the battery cables from battery terminals:
A. POSITIVE (+) RED battery cable from the POSITIVE (+) battery terminal.
B. NEGATIVE (‐) BLACK battery cable from NEGATIVE (‐) battery terminal.
NEGATIVE (-) BLACK Battery Cable
POSITIVE (+) RED Battery Cable
POSITIVE (+) RED
Battery Cap
NEGATIVE (-) BLACK
Battery Terminal with
Locknut and Mounting Bolt
POSITIVE (+) RED Battery
Terminal with Locknut and
Mounting Bolt
NEGATIVE (-) BLACK
Battery Cap
12 Volt Battery
39
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10—BATTERIES
Charging the Batteries
ꢀ WARNING
NEVER attempt to recharge the batteries by attaching cables directly to the
battery terminals or clamps.
DO NOT attempt to recharge the batteries and operate the powered scooter at
the same time.
Only use the provided charger with this product.
CAUTION
New batteries MUST be fully charged prior to initial use of the powered scooter.
DO NOT sit in the scooter while recharging the batteries.
ALWAYS charge new batteries before initial use or battery life will be reduced.
As a general rule, you should recharge your batteries as frequently as possible to
assure the longest possible life and to minimize required charging time. Plan to
recharge them when you do not anticipate using the powered scooter.
The range per battery charge using recommended batteries should be approximately five
to nine hours of typical operation. Extensive use on inclines may substantially reduce per
charge mileage.
NOTE: For this procedure, refer to FIGURE 10.4 on page 41.
NOTE: The powered scooter is designed with an electrical lockout to prevent it from being driven
while the charger is plugged into an outlet.
NOTE: Always charge the batteries completely until the battery charger light turns GREEN.
1. Turn the key to the Off position.
3. Lifting up on trunk lid, release the hook and loop strips and remove the trunk lid from
the scooter.
4. Open the charger port cover.
5. Plug one end of the charger cable into the battery charger port located on the scooter.
6. Plug the other end of the charger cable into 110‐volt wall outlet.
NOTE: The battery charger light will be YELLOW or RED.
7. Allow the batteries to charge until the charger light turns GREEN.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10—BATTERIES
8. Perform one of the following:
• Battery charger light turns GREEN ‐ Unplug the charger cable from the scooter and
the wall outlet.
• Battery charger light flashes GREEN for over 40 minutes ‐ Perform the following
steps:
i. Check that the charger cable is correctly connected to the scooter and the wall
outlet.
ii. Check that the scooter is turned off.
iii. If steps i and ii do not correct the problem, contact a qualified technician.
9. Unplug the charger cable from the wall outlet.
10. Unplug the charger cable from the scooter.
11. Close the charger port cover.
12. Position the trunk lid onto the scooter and press to secure the hook and loop strips.
Trunk Lid
Connect to
Scooter
Charger Cable
BatteryCharger
Port
Connect to
Wall Outlet
Charger Cable
41
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 11—TRANSPORTING
SECTION 11—TRANSPORTING
ꢀ WARNING
After any adjustments, repair or service and before use, make sure that all attaching
hardware is tightened securely - otherwise injury or damage may result.
Before performing any maintenance, adjustment or service, turn power off and
remove key from ignition.
DO NOT lift the scooter by the rear shroud - otherwise damage to the scooter may
occur.
Transporting the Scooter
NOTE: For this procedure, refer to FIGURE 11.1 on page 43.
Disassembling
1. Turn power off and remove the key from the ignition.
2. Remove any installed accessories.
5. Disconnect the tiller wiring connector from the controller wiring connector
(Detail “A”).
6. Hold the seat post with one hand.
7. With the other hand, push the release lever to the rear of the scooter (Detail “A”).
8. Lift the seat post to separate the front frame assembly from the rear frame assembly
pins.
Assembling
2. Position the rear frame between the curved locking brackets of the front frame
assembly.
3. Hold the seat post and align the curved locking brackets on the front frame assembly
with the rear frame assembly pins.
4. While holding the seat post, slowly lower the front frame assembly onto the rear frame
assembly pins until the release lever locks.
5. Connect the tiller wiring connector to the controller wiring connector.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 11—TRANSPORTING
8. If necessary, install any accessories to be used.
DETAIL “A”
Front Frame
Assembly
Release Lever
Rear Frame
Assembly
Tiller Wiring
Connector
Controller Wiring Connector
Seat Post
Front Frame Assembly Curved Bracket
Rear Frame Assembly Pins
Front Frame Assembly
43
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 12—ACCESSORIES
SECTION 12—ACCESSORIES
ꢀ WARNING
After ANY adjustments, repair or service and before use, make sure that all
attaching hardware is tightened securely - otherwise injury or damage may result.
Before performing any maintenance, adjustment or service, turn power off and
remove key from ignition.
NOTE: The crutch/cane holder, safety flag, rear mounted basket and oxygen holder all install into
one of two accessory tubes. More than one accessory may be installed at one time depending on
accessories installed.
Installing/Removing the Crutch/Cane Holder
ꢀ WARNING
The installation of the crutch/cane holder onto the back of the scooter seat signifi-
cantly increases the length of the scooter. When turning the scooter or swiveling
the scooter seat, it is important to take note of this increased length - otherwise,
injury and/or damage to the surrounding property may result.
NOTE: For this procedure, refer to FIGURE 12.1.
Installing
1. Install the crutch/cane holder into the accessory tube located on the back of the seat.
2. Install the mounting knob to secure the crutch/cane holder in place. Securely tighten.
3. Align the slot on the base with the hook on the crutch/cane holder and slide base down
into position.
Removing
Crutch
Cane
Holder
1. Remove the crutch/cane holder from
the accessory tube.
2. Remove the mounting knob that
secures the crutch/cane holder in place.
Hook
3. Remove the crutch/cane holder from
the accessory tube.
Mounting
Knob
Accessory
Tubes
Base
44
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 12—ACCESSORIES
Installing/Removing the
Safety Flag
ꢀ WARNING
The installation of the safety flag onto the back of the scooter seat significantly
increases the length of the scooter. When turning the scooter or swiveling the
scooter seat, it is important to take note of this increased length - otherwise, injury
and/or damage to the surrounding property may result.
NOTE: For this procedure, refer to FIGURE 12.2.
Installing
1. Install the bracket into the accessory tube located on the back of the seat.
2. Install mounting knob to secure the bracket in place. Securely tighten.
3. Install safety flag into bracket.
Removing
Safety Flag
1. Remove the safety flag from the
bracket.
Bracket
2. Remove the mounting knob that
secures the bracket in place.
Mounting
3. Remove the bracket from the accessory
tube located on the back of the seat.
Accessory
Tubes
Knob
Installing/Removing/Using the Walker Holder
ꢀ INSTALLATION WARNINGS
After ANY adjustments, repair or service and before use, make sure that all
attaching hardware is tightened securely.
The installation of the walker holder onto the back of the scooter seat significantly
increases the length of the scooter. When turning the scooter or swiveling the
scooter seat, it is important to take note of this increased length - otherwise, injury
and/or damage to the surrounding property may result.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 12—ACCESSORIES
Installing/Removing the Walker Holder
NOTE: For this procedure, refer to FIGURE 12.3.
NOTE: Reverse this procedure to remove the walker holder.
1. If necessary, loosen but DO NOT remove the mounting knob.
2. Install the walker holder into the accessory tube.
3. Thread the mounting knob into the welded nut on the accessory tube. Securely
tighten.
Walker Holder
Mounting
Knob
Accessory Tubes
Using the Walker Holder
NOTE: For this procedure, refer to FIGURE 12.4.
1. Fold walker. Refer to walker instructions.
NOTE: Walker MUST be folded before using walker holder.
2. Hang folded walker on walker holder hooks.
3. Secure walker with hook and loop straps.
Hook
Hook and
Loop Strap
Mounting
Knob
Accessory Tubes
46
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 12—ACCESSORIES
Installing/Removing the Rear Mounted Basket
ꢀ WARNING
The rear mounted basket is rated for a maximum capacity of ten lbs.
After ANY adjustments, repair or service and before use, make sure that all
attaching hardware is tightened securely.
The installation of the basket and basket bracket onto the back of the scooter seat
increases the length of the scooter. When turning the scooter or swiveling the
scooter seat, it is important to take note of this increased length - otherwise, injury
and/or damage to surrounding property may occur.
NOTE: For this procedure, refer to FIGURE 12.5.
Installing
1. Loosen but DO NOT remove the mounting knob.
2. Install the basket bracket into the accessory tube.
3. Thread the mounting knob into the welded nut on the accessory tube. Securely
tighten.
4. Align the mounting clips on the bracket with the slots on the basket and slide the
basket down securely into position.
Removing
1. Remove the basket from the bracket.
2. Loosen the mounting knob.
3. Remove the basket bracket from the accessory tube.
4. Tighten the mounting knob.
Mounting Clips
Rear Basket
Slots
Mounting
Knob
Accessory Tubes
Basket Bracket
47
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL
LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.
This warranty is extended only to the original purchaser/user of our products.
This warranty gives you specific legal rights and you may also have other legal rights which vary from
state to state.
Invacare warrants all electronics and electrical components (excluding batteries), transaxle and
frame to be free from defects in materials and workmanship for a period of twelve (12) months from
the date of purchase from Invacare or a dealer. Invacare warrants all batteries for a period of six (6)
months from the date of purchase from Invacare or a dealer. If within such warranty period any such
product shall be proven to be defective, such product shall be repaired or replaced at Invacare's
option. This warranty does not include any labor or shipping charges incurred in replacement part
installation or repair of any such product. Invacare’s sole obligation and your exclusive remedy under
this warranty shall be limited to such repair and/or replacement.
For warranty service, please contact the dealer from whom you purchased your Invacare product. In
the event you do not receive satisfactory warranty service, please write directly to Invacare at the
address on the bottom of the back cover. Provide dealer's name address, date of purchase, indicate
nature of the defect and, if the product is serialized, indicate the serial number. Do not return
products to our factory without our prior consent.
LIMITATIONS AND EXCLUSIONS: THE FOREGOING WARRANTY SHALL NOT APPLY TO
SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED,
PRODUCTS SUBJECT TO NEGLIGENCE, ACCIDENT, IMPROPER OPERATION,
MAINTENANCE OR STORAGE, COMMERCIAL OR INSTITUTIONAL USE, PRODUCTS
MODIFIED WITHOUT INVACARE'S EXPRESS WRITTEN CONSENT INCLUDING, BUT NOT
LIMITED TO, MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR
ATTACHMENTS; PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY
COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE, OR TO A PRODUCT
DAMAGED BY CIRCUMSTANCES BEYOND INVACARE'S CONTROL, AND SUCH
EVALUATION WILL BE SOLELY DETERMINED BY INVACARE. THE WARRANTY SHALL NOT
APPLY TO PROBLEMS ARISING FROM NORMAL WEAR OR FAILURE TO ADHERE TO THESE
INSTRUCTIONS. A CHANGE IN OPERATING NOISE, PARTICULARLY RELATIVE TO MOTORS
AND GEARBOXES DOES NOT CONSTITUTE A FAILURE. ALL SUCH DEVICES WILL EXHIBIT
A CHANGE IN OPERATING NOISE DUE TO AGING.
THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER
WARRANTIES WHATSOEVER, WHETHER EXPRESS OR IMPLIED, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND
THE SOLE REMEDY FOR VIOLATIONS OF ANY WARRANTY WHATSOEVER, SHALL BE
LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PURSUANT TO THE
TERMS CONTAINED HEREIN, THE APPLICATION OF ANY IMPLIED WARRANTY
WHATSOEVER SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESS
WARRANTY PROVIDED HEREIN. INVACARE SHALL NOT BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER.
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE/PROVINCIAL LAWS
AND REQUIREMENTS.
Invacare Corporation
USA
Canada
One Invacare Way
Elyria, Ohio USA
44036-2125
570 Matheson Blvd E Unit 8 All rights reserved. Trademarks are
Mississauga Ontario
L4Z 4G4 Canada
800-668-5324
identified by the symbols ™ and ®. All
trademarks are owned by or licensed to
Invacare Corporation unless otherwise
noted.
800-333-6900
© 2007 Invacare Corporation
Part No. 1145807
Rev B - 10/07
Download from Www.Somanuals.com. All Manuals Search And Download.
|