Integra Car Video System DSR 73 User Manual
Contents  
Before UsingYour DVD Receiver  
DVD Receiver  
Getting Started  
DSR-7.3  
Instruction Manual  
Setup  
Basic Operation  
Thank you for purchasing the Integra DVD  
Receiver.  
Advanced Operation  
Please read this manual thoroughly before  
making connections and turning on the  
power.  
Following the instructions in this manual will  
enable you to obtain optimum performance  
and listening enjoyment from your new DVD  
Receiver.  
Please retain this manual for future reference.  
Other  
E
Download from Www.Somanuals.com. All Manuals Search And Download.  
21. Replacement Parts – When replacement parts are  
required, be sure the service technician has used  
replacement parts specified by the manufacturer or have  
the same characteristics as the original part.  
Unauthorized substitutions may result in fire, electric  
shock, or other hazards.  
22. Safety Check – Upon completion of any service or  
repairs to the appliance, ask the service technician to  
perform safety checks to determine that the appliance is  
in proper operation condition.  
FIGURE 1:  
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL  
ELECTRICAL CODE, ANSI/NFPA 70  
ANTENNA  
LEAD IN  
WIRE  
GROUND  
CLAMP  
23. Wall or Ceiling Mounting – The appliance should be  
mounted to a wall or ceiling only as recommended by the  
manufacturer.  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRIC  
SERVICE  
EQUIPMENT  
24. Heat – The appliance should be situated away from heat  
sources such as radiators, heat registers, stoves, or  
other appliances (including amplifiers) that produce heat.  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
25. Liquid Hazards – The appliance should not be exposed  
to dripping or splashing and no objects filled with liquids,  
such as vases should be placed on the appliance.  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
NEC – NATIONAL ELECTRICAL CODE  
S2898A  
Precautions  
For U.S. model  
For Canadian model  
The laser is covered by a housing which prevents exposure during  
operation or maintenance. However, this product is classified as a  
Laser Product by CDRH (Center for Devices and Radiological  
Health) which is a department of the Food and Drug Administration.  
According to their regulations 21 CFR section 1002.30, all  
manufactures who sell Laser Products must maintain records of  
written communications between the manufacturer, dealers and  
customers concerning radiation safety. If you have any complaints  
about instructions or explanations affecting the use of this product,  
please feel free to write to the address on the back page of this  
manual. When you write us, please include the model number and  
serial number of your unit.  
This class B digital apparatus complies with Canadian ICES-003.  
For models having a power cord with a polarized plug:  
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE  
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.  
Modèle pour les Canadien  
Cet appareil numérique de la classe B est conforme à la norme  
NMB-003 du Canada.  
In compliance with Federal Regulations, the certification,  
identification and the period of manufacture are indicated on the rear  
panel.  
Sur les modèles dont la fiche est polarisee:  
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,  
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA  
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER  
JUSQU’AU FOND.  
FCC INFORMATION FOR USER  
CAUTION:  
The user changes or modifications not expressly approved by the  
party responsible for compliance could void the user’s authority to  
operate the equipment.  
NOTE:  
This equipment has been tested and found to comply with the limits  
for a Class B digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment  
generates, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from  
that to which the receiver is connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
Note to CATV system installer:  
This reminder is provided to call the CATV system installer’s  
attention to Article 820-40 of the NEC, ANSI/NFPA 70, which  
provides guidelines for proper grounding and, in particular, specifies  
that the cable ground shall be connected to the grounding system of  
the building, as close to the point of cable entry as practical.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Precautions  
DANGER:  
7. Location of the unit  
• Place the unit in a well-ventilated location.  
VISIBLEAND INVISIBLE LASER RADIATION WHEN OPENAND  
INTERLOCK FAILED OR DEFEATED. DO NOT STARE INTO  
BEAM.  
Take special care to provide plenty of ventilation on all sides of  
the unit especially when it is placed in an audio rack. If ventilation  
is blocked, the unit may overheat and malfunction.  
• Do not expose the unit to direct sunlight or heating units as the  
unit's internal temperature may rise and shorten the life of the  
pickup.  
• Avoid damp and dusty places and places directly affected by  
vibrations from the speakers. In particular, avoid placing the unit  
on or above one of the speakers.  
CAUTION:  
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR  
ADJUSTMENTS OR PERFORMANCE OF PROCEDURES  
OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN  
HAZARDOUS RADIATION EXPOSURE.  
• Be sure the unit is placed in a horizontal position. Never place it  
on its side or on a slanted surface as it may malfunction.  
• When you place the unit near a TV, radio, or VCR, the playback  
picture may become poor and the sound may be distorted. In  
this case, place the unit away from the TV, radio, or VCR.  
This unit contains a semiconductor laser system and is classified  
as a “CLASS 1 LASER PRODUCT.” So, to use this model properly,  
read this Instruction Manual carefully. In case of any trouble,  
please contact the store where you purchased the unit. To prevent  
being exposed to the laser beam, do not try to open the enclosure.  
8. Care  
From time to time you should wipe the front and rear panels and  
the cabinet with a soft cloth. For heavier dirt, dampen a soft cloth  
in a weak solution of mild detergent and water, wring it out dry, and  
wipe off the dirt. Following this, dry immediately with a clean cloth.  
Do not use rough material, thinners, alcohol or other chemical  
solvents or cloths since these could damage the finish or remove  
the panel lettering.  
9. Notes on Handling  
1. This unit is a CLASS 1 LASER PRODUCT and employs a  
laser inside the cabinet.  
• When shipping the unit, use the original shipping carton and  
packing materials. For maximum protection, repack the unit as  
it was originally packed at the factory.  
2. To prevent the laser from being exposed, do not remove the  
cover. Refer servicing to qualified personnel.  
• Do not use volatile liquids, such as insect spray, near the unit.  
Do not leave rubber or plastic products in contact with the unit  
for a long time. They will leave marks on the finish.  
• The top and rear panels of the unit may become warm after a  
long period of use.This is not a malfunction.  
• When the unit is not in use, be sure to remove the disc and turn  
off the power.  
• If you do not use the unit for a long period, the unit may not  
function properly in the future. Turn on and use the unit  
occasionally.  
1. Regional Restriction Codes (Region Number)  
Regional restriction codes are built into DVD Receivers and DVD  
videos for each sales region. If the regional code of the DVD  
Receiver does not match one of the regional codes on the DVD  
video, playback is not possible.  
The regional number can be found on the rear panel of the DVD  
1
Receiver. (e.g.  
for Region 1)  
2. About This Manual  
10. To Obtain a Clear Picture  
This manual explains the basic procedures for operating the DVD  
Receiver. Some DVD videos do not support the full potential of the  
DVD technology. Your DVD Receiver may therefore not respond  
to all operating commands. Refer to instruction notes on discs.  
The unit is a high technology, precision device. If the optical pick-  
up lens and disc drive parts are dirty or worn down, the picture  
quality becomes poor. To obtain a clear picture, we recommend  
regular inspection and maintenance (cleaning or parts  
replacement) every 1,000 hours of use depending on the operating  
environment. For details, contact your nearest dealer.  
A “  
” mark may appear on the TV screen during operation. It  
means that the operation is not permitted by the DVD Receiver or  
the disc.  
11. Notes on Moisture Condensation  
3. Recording Copyright  
Moisture condensation damages the unit.  
Please read the following carefully.  
Recording of copyrighted material for other than personal use is  
illegal without permission of the copyright holder.  
• What is moisture condensation?  
4. AC Fuse  
Moisture condensation occurs, for example, when you pour a  
cold drink into a glass on a warm day. Drops of water form on  
the outside of the glass. In the same way, moisture may condense  
on the optical pick-up lens inside the unit, one of the most crucial  
internal parts of the unit.  
The fuse is located inside the chassis and is not user-serviceable.  
If power does not come on, contact your Integra/Onkyo authorized  
service center.  
5. Power  
WARNING  
• Moisture condensation occurs in the following cases.  
– When you bring the unit directly from a cold place to a warm  
place.  
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ  
THE FOLLOWING SECTION CAREFULLY.  
– When you use the unit in a room where you just turned on the  
heater, or a place where the cold wind from the air conditioner  
directly hits the unit.  
– In summer, when you use the unit in a hot and humid place  
just after you move the unit from an air conditioned room.  
– When you use the unit in a humid place.  
The voltage of the available power supply differs according to  
country or region. Be sure that the power supply voltage of the  
area where the unit will be used meets the required voltage (AC  
120V 60Hz or AC 230-240V 50Hz) written on the rear panel.  
6. Do not touch the unit with wet hands  
Do not handle the unit or power cord when your hands are wet or  
damp. If water or any other liquid enters the case, take the unit to  
an authorized service center for inspection.  
• Do not use the unit when moisture condensation may occur.  
If you use the unit in such a situation, it may damage discs and  
internal parts. Remove the disc, connect the power cord of the  
unit to the wall outlet turn on the unit, and leave it for two or  
three hours. After a few hours, the unit will have warmed up and  
evaporated any moisture. Keep the unit connected to the wall  
outlet and moisture condensation will seldom occur.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Important Safeguards/Precautions/Table of Contents .................................... 2/3/5  
Getting Started  
Features ................................................................................................................ 6  
Supplied Accessories ............................................................................................ 7  
Notes on Discs ...................................................................................................... 8  
Index to Parts and Controls ................................................................................ 10  
Preparing the Remote Controller ........................................................................ 15  
Connecting to a TV ............................................................................................. 16  
Connecting Speakers.......................................................................................... 17  
Positioning Speakers .......................................................................................... 18  
Connecting to Audio/Video Equipment................................................................ 19  
z Connection for the Integra/Onkyo Cassette Tape Deck, CD Recorder  
or MD Recorder .................................................................................................. 20  
Operating Components not Reached by the Remote Controller Signals (IR IN) 21  
Making Antenna Connections ............................................................................. 22  
Setup  
Connecting the Power/Turning on the DVD Receiver ......................................... 24  
Speaker Setup .................................................................................................... 26  
Basic Operation  
Getting Started Using Your DVD Receiver.......................................................... 29  
Listening to the Radio ......................................................................................... 35  
Playing the Connected Source ........................................................................... 38  
Various Functions Common to all the Sources ................................................... 40  
Using the Timer Functions .................................................................................. 41  
Enjoying the Sound Effects ................................................................................. 46  
Advanced Operation  
Locating a Specific Title/Folder/Chapter/Track/Location ..................................... 52  
Repeat Play ........................................................................................................ 54  
Still Frame/Slow Play .......................................................................................... 55  
Playing in a Favourite Order ............................................................................... 56  
Random Play ...................................................................................................... 60  
Selecting the Audio/Subtitle Language ............................................................... 61  
Continuing Playback from a Specified Location (Last Memory) ......................... 62  
Selecting the Camera Angle ............................................................................... 63  
Viewing Disc Information..................................................................................... 64  
Customizing the Function Settings ..................................................................... 66  
Controlling a TV connected to the DVD Receiver ............................................... 78  
Recording Using the Connected Equipment ....................................................... 80  
Other  
Troubleshooting .................................................................................................. 81  
Specifications ...................................................................................................... 84  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Features  
*
“DTS” and “DTS Digital Surround” are trademarks of  
Digital Theater Systems, Inc.  
Receiver Features  
** Manufactured under license from Dolby Laboratories.  
“Dolby”, “Pro Logic” and the double-D symbol are  
trademarks of Dolby Laboratories. Confidential  
Unpublished Works. ©1992-1997 Dolby Laboratories.  
All rights reserved.  
25 watts per channel into 6 ohms (FTC)  
20 watts per channel into 6 ohms (DIN)  
30 watts per channel into 6 ohms (EIAJ)  
96 kHz/24-Bit DAC System  
DTS* & Dolby** Digital Decoders  
Acoustic Control  
*** “Theater-Dimensional” is a trademark of Onkyo  
Corporation.  
1 Digital Input/1 Output  
Subwoofer Preout  
2 Audio Inputs/1 Output  
Theater-Dimensional***  
30 FM/AM Presets  
IPM (Intelligent Power Management)  
Sleep Timer  
Timer Play  
DVD/CD Player Features  
DTS, Dolby Digital, and PCM Compatible  
Component-Video Output  
1 S-Video Output  
Progressive Scan  
27 MHz/10-Bit Video DAC  
Plays DVDs, MP3 CDs, CD-Rs, CD-RWs, Video CDs and  
Audio CDs  
High-Resolution On-screen Display  
Program Memory Playback  
Auto Last Play  
Dual-Wavelength Optical Pickup  
Sand-Blasted Aluminum Front Panel  
Other Features  
Full Function z-compatible Remote Control  
Preprogrammed Remote Control  
Memory Preservation  
This unit does not require memory preservation batteries.  
A built-in memory power backup system preserves the  
contents of memory during power failures and even when  
the power cord is unplugged.  
The power cord must be plugged in order to charge the  
backups system. The memory preservation period after  
the unit has been turned off varies depending on climate  
and placement of the unit. On average, memory contents  
are protected over a period of a few weeks after the time  
the unit has been turned off. This period is shorter when  
the unit is exposed to a very humid climate.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Supplied Accessories  
Make sure your box contains everything listed below.  
If any pieces are missing, contact your nearest Integra/Onkyo dealer.  
The number of accessories is indicated in brackets.  
Remote controller (RC-507M) [1]  
Speaker Label [1]  
1
2
3
Speaker Cable  
Batteries (size AA/R6/UM3) [2]  
AM loop antenna [1]  
FM antenna [1]  
Power cord [1]  
Audio/video  
connection cable [1]  
S video connection  
cable [1]  
The cable with the  
yellow plug is for video.  
The cable with the red  
and white plugs are for  
audio.  
Cable which sends S-  
video images.  
The alphabet displayed at the end of the product name  
found in catalogs and on the package represents the  
color of this DVD receiver. Though the color varies, the  
specifications and operations are the same.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes on Discs  
This section shows you how to handle, clean, and store discs.  
About VIDEO CDs  
Playable Discs  
This DVD Receiver supports VIDEO CDs equipped with the  
PBC (Version 2.0) function. (PBC is the abbreviation of  
Playback Control.)  
You can enjoy two playback variations depending on the type  
of disc.  
This DVD Receiver can playback the following discs.  
Disc mark  
• VIDEO CD not equipped with PBC function (Version 1.1)  
DVD videos  
VIDEO CDs  
Sound and movies can be played on this DVD Receiver in  
the same way as an audio CD.  
• VIDEO CD equipped with PBC function (Version 2.0)  
In addition to operation of the VIDEO CD not equipped with  
the PBC function, you can enjoy playback with interactive  
software and search function using the menu displayed on  
the TV screen (Menu Playback). Some of the functions  
described in this Instruction Manual may not work with some  
discs.  
*1  
*1  
Audio CDs  
MP3 compatibility information  
*1 This unit can play CD-R and CD-RW discs recorded in CD  
Audio or Video CD format, or with MP3 audio files.  
However, there may be some discs that cannot be played  
back with this unit. The causes of this impossibility include  
incompletion of disc finalization and the recording  
characteristics of the recorder as well as the properties,  
damage or stain of the disc in use and stain or  
• The CD-ROM must be ISO9660 compatible.  
• Files should be MPEG1 Audio Layer 3 format, 44.1 or  
48kHz, fixed bit-rate. Incompatible files will not play and  
“UNPLAYABLE MP3 FORMAT” will be displayed.  
• This DVD Receiver is not compatible with variable bit-rate  
(VBR) files. Be sure to make MP3 CD with fixed bit-rate  
setting.  
• This system only plays tracks that are named with the file  
condensation on the pickup lens of this unit. For details,  
extension “.mp3” or “.MP3”.  
please refer to the instruction manual of the recorder.  
• This system is not compatible with multi-session discs. If  
you try an play a multi-session disc, only the first session  
will be played.  
• Use CD-R or CD-RW media for recording your MP3 files.  
The disc must be finalized in order to play.  
• Audio encoded at 128kbps should sound close to regular  
audio CD quality. Although this system will play lower bit-  
rate MP3 tracks, the sound quality becomes noticeably  
worse at lower bit-rates.  
• Only the first 8 characters of folder and track names  
(excluding the “.mp3” extension) are displayed.  
• This system can recognize a maximum of 250 folders and  
250 tracks. Discs containing more than 250 folders or tracks  
will not play.  
• You cannot playback discs other than those listed above.  
• You cannot play discs such as DVD-RAM, DVD-RW, DVD-  
Audio, Photo CD, CD-G etc., even if the marks in the  
above table are labeled on those discs.  
• This DVD Receiver uses the PAL/NTSC color system, and  
cannot playback DVD videos recorded in any other color  
system (SECAM, etc.).  
• Avoid using heart-shaped or octagonal discs. Playing  
irregularly shaped discs may damage the internal  
mechanism of the DVD Receiver.  
Notes on Copyright  
• Do not use discs that have residue from adhesive tape,  
rental discs that have peeling labels, or discs that have  
custom labels or stickers. Otherwise, you may not be able  
to eject the discs or the DVD Receiver may become  
inoperative.  
It is forbidden by law to copy, broadcast, show, broadcast on  
cable, play in public, and rent copyrighted material without  
permission.  
DVD videos are copy protected, and any recordings made from  
these discs will be distorted.  
This product incorporates copyright protection technology that is  
protected by method claims of certain U.S. patents and other  
intellectual property rights owned by Macrovision Corporation  
and other rights owners. Use of this copyright protection  
technology must be authorized by Macrovision Corporation, and  
is intended for home and other limited viewing uses only unless  
otherwise authorized by Macrovision Corporation. Reverse  
engineering or disassembly is prohibited.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Handling Discs  
Differences in Disc Composition  
• Do not touch the playback side of the disc.  
I DVD  
All discs are divided up into smaller, more manageable  
sections so that you can find specific content more easily.  
DVDs are divided into one or more titles. Each title may be  
further divided into several chapters. Occassionally, a chapter  
may contain index points, effectively dividing the chapter up  
into several parts, too.  
Playback side  
• Do not attach paper or tape to discs.  
Title 1  
Chapter 2  
Title 2  
Chapter 2  
Chapter 1  
Chapter 1  
Cleaning Discs  
DVD  
• Fingerprints and dust on the disc cause picture and sound  
deterioration. Wipe the disc from the center outwards with a  
soft cloth. Always keep the disc clean.  
I Video CD/CD  
Video CDs and CDs are divided into a number of tracks. In  
rare cases, a track may contain a number of index points,  
effectively dividing the track up into several parts.  
Track 2  
Track 1  
Track 3  
Track 4  
• If you cannot wipe off the dust with a soft cloth, wipe the disc  
lightly with a slightly moistened soft cloth and finish with a  
dry cloth.  
• Do not use any type of solvent such as thinner, benzine,  
commercially available cleaners or antistatic spray for vinyl  
LPs. It may damage the disc.  
Video CD  
Track 2  
Track 1  
Track 3  
Track 4  
Track 5  
Storing Discs  
• Do not store discs in a place subject to direct sunlight or  
near heat sources.  
CD  
• Do not store discs in places subject to moisture and dust  
such as a bathroom or near a humidifier.  
• Store discs vertically in a case. Stacking or placing objects  
on discs outside of their case may cause warping.  
I MP3  
MP3 (MPEG1 Audio Layer 3) is a compressed audio file  
format. Files are recognized by their file extension “.mp3” or  
“.MP3”. Folders that contain MP3 files are automatically  
numbered F_001, F_002, etc. Tracks within folders are  
automatically numbered T_001, T_002, etc.  
Folder 1  
Track 2  
Folder 2  
Track 1  
Track 3  
Track 1  
Track 2  
MP3  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index to Parts and Controls  
For operational instructions, refer to the page indicated in brackets.  
IFront panel  
1
2 34  
5
6
7
8
9
0 - = ~  
!
@ # $  
% ^  
1 Standby/On button, On, Standby indicators [24]  
When Standby/On button is pressed to On, the DVD Receiver turns  
on. The Standby indicator turns off, and the On indicator and the  
display lights up. Pressing the button again returns the DVD  
Receiver to the standby state. This state turns off the display,  
disables control functions.  
~ Play button [29, 33, 34]  
Press to start or resume playback.  
! 4/¢,Tuning/Preset 2/3 buttons [33, 35, 37]  
Press to go back to previous or advance to next chapters/tracks.  
Also, use these buttons to change the tuner frequency.  
2 Progressive Scan indicator [69]  
@ Preset Memory button [35-38]  
Lights up when the DVD Receiver is set to progressive-scan video.  
Press to assign the radio station that is currently tuned in to a  
preset channel or delete a previously preset station.  
3 IPM (Intelligent Power Management) indicator [25]  
Lights up when the IPM function is active.  
# Stereo/Theater-Dimensional button [48, 49]  
Press to switch the listening mode between “STEREO” and  
“THEATER-DIMENSIONAL”.  
4 Theater-Dimensional indicator [48]  
Lights up while in the Theater-Dimensional mode.  
$ Surround Mode button [49]  
5 Display [11, 40]  
Press to select a surround mode.  
6 Remote control sensor [15]  
Point the remote control toward the remote sensor to operate the  
DVD Receiver.  
% Input 2/3 buttons [35, 37, 38]  
Press to select an input source other than DVD.  
^ Acoustic Control button and indicator [51]  
Press to change the acoustic mode to boost super bass/high  
frequency sounds. When acoustic control mode is on the  
“A.CTRL 1 or 2” indicator lights.  
7 Master Volume control [40]  
The Master Volume dial is used to control the volume level.  
8 Phones jack [40]  
This is a standard stereo jack for connecting stereo headphones.  
9 Disc tray [29, 34]  
When loading a disc, place discs in the disc tray with the label side  
facing up.  
0 Open/Close button [29, 34]  
Press to open and close the disc tray.  
- Pause button [29]  
Press to pause playback. Press again to resume playback.  
= Stop button [34]  
Press to stop playback. Pressing once enables playback to resume  
from a point shortly before the location where it was stopped.  
Pressing twice causes the disc to return to the beginning of the  
disc when playback starts again.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IDisplay  
12 3 4  
5 6  
7
8 9 0 -  
= ~  
1 Multipurpose display  
9 LAST indicator [62]  
Lights up when a disc which contains a memorized Last Memory  
point is loaded.  
2 TITLE, CHP indicators [52, 56, 64, 65]  
Indicate display mode of the current title or chapter of DVD.  
0 REMAIN indicator [64, 65]  
Lights up when time remaining is displayed.  
3 Inserted disc indicator [29]  
Indicates the type of current disc that is loaded.  
- MUTING indicator [40]  
Flashes when the mute function is active.  
4 £, 8 indicators [29]  
Lights up in play or pause mode.  
= 3¶2, AUTO, FM STEREO indicators [35]  
Indicate the reception mode.  
5 TIMER indicator [42]  
Lights up when the respective timer is set.  
~ TRACK indicator [52, 56, 64, 65]  
Lights up when the current track of Video CD or CD is displayed.  
6 RPT indicator [54]  
Illuminates during repeat playback. Also RPT indicator illuminates  
during A-B repeat playback.  
7 Source/Listening mode indicators [38, 47, 49]  
One of the source indicators lights to show the format of the current  
source.  
8 SLEEP indicator [42]  
Lights up when the sleep timer is active.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index to Parts and Controls  
Remote controller  
Explanations on this page are for controlling the DVD receiver. The  
supplied remote controller is a useful tool to help you operate your  
home theater.  
1 Send indicator [15, 78]  
Lights red when sending a signal.  
To operate other components, see “Operating the Integra/Onkyo  
Cassette Tape Deck/MD Recorder/CD Recorder with the Supplied  
Remote Controller” on page 39 and “Controlling a TV connected to  
the DVD Receiver” on page 78.  
2 Open/Close button [29]  
Opens and closes the disc tray.  
3 On button [24, 30, 66]  
Turns on the DVD Receiver.  
4 Input Selector 2/3 buttons [35, 37, 38]  
Press to select the input source.  
1
en  
5 Mode buttons [15]  
For selecting the component to be operated by the remote controller.  
6 Sleep button [42]  
For setting the sleep timer.  
_
+
2
3
4
7 Dimmer button [40]  
Se  
l
For adjusting the brightness of the front display.  
o
8 Top Menu button [32, 52]  
5
6
7
Press to call up the top menu programmed on the DVD. Depending  
on the DVD, the top menu may be identical to the DVD menu.  
¡
™
£
9 (Mode Recvr is selected) Tun +/– buttons [37]  
8
For selecting a tuner preset channel.  
Step/Slow  
(Mode DVD is selected) Step/Slow +/– buttons [55]  
Press Step/Slow +/– during playback to view still frame. Press and  
hold Step/Slow +/– during playback to view slow playback. In still  
frame, press Step/Slow + to advance DVDs and Video CDs frame  
by frame and Step/Slow – to back up a few frames at a time (DVD  
only)  
CH  
Tun  
ENTER  
VOL  
¢
9
0
∞
§
•
-
T D/ST  
Muting  
-
=
~
!
Surround  
A.Control  
0 Cursor (2/3/5/∞/ENTER) [29, 30, 41-45, 56-59, 66]  
Use to move through the options on menu screens. Press to enter  
settings.  
ª
@
#
-
Repeat  
A B  
- T-D/ST button [48, 49]  
Press to switch the listening mode between “STEREO” and  
“THEATER-DIMENSIONAL”.  
º
–
Late Night  
Audio  
Timer  
$
%
^
&
*
≠
Ÿ
⁄
¤
‹
= Return button [32, 66, 74, 76, 77]  
Angle  
Subtitle FM Mode  
Use to go one menu back (current settings are maintained). Use Return  
when you do not want to change the option setting in a menu.  
Last M  
Program Random  
Clear  
~ Surround button [49]  
SP Setup  
1
SW Mode  
Test Tone  
CH Sel  
Press to select the surround mode.  
2
Distance  
5
3
! 4/¢ buttons [33, 35, 37, 60]  
4
IPM  
7
6
Up/Down  
9
(
)
During playback of DVD, CD and Video CD, press 4 to go back  
to a previous chapter/track and ¢ to advance to the next chapter/  
track.  
-
T D Setup  
8
+
10  
-- ---  
0
Search  
Enter  
›
/
@ 7 button [34]  
Press to stop playback (DVD). Pressing once enables playback to  
resume from a point shortly before the location where it was  
stopped. Pressing twice causes the disc to return to the beginning  
of the disc when playback starts again.  
-
RC 507  
M
# Repeat button [54]  
To control the DVD receiver, press Mode DVD or Mode  
Recvr first. Press Mode DVD to operate the DVD section, or  
Mode Recvr to operate the receiver section. Functions of  
grayed buttons in the illustration vary depending on the  
mode.  
Use to set the repeat mode.  
$ Late Night button [51]  
Press to change the late night setting.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
% Audio button [61]  
º A-B button [54]  
Press repeatedly to select one of the audio languages programmed  
Press at the beginning and end of the section you want to repeat or  
on a DVD.  
to mark a location you want to return to.  
For Video CD and MP3, each press changes the audio output as  
follows.  
–
button [29, 32, 55]  
→ Stereo → 1/L(Left) → 2/R(Right)  
Press to pause disc playback. Press again to resume playback.  
^ Angle button [63]  
≠ Timer button [41-45]  
Some DVDs are recorded with various camera angle playback  
options. Press Angle repeatedly to display different camera angles.  
Press to activate a timer function or to set a timer program.  
Ÿ FM Mode button [35, 39]  
& Last M button [62]  
For AM/FM input, press to switch between FM Stereo auto and  
mono.  
You can resume DVD or Video CD playback from the point you last  
watched even if the disc is removed from the DVD receiver. Press  
Last M during playback to set a Last Memory Point. When you  
want to resume playback of that disc, press Last M in the stop  
mode and playback starts from the memorized point. Last Memory  
locations can be stored for up to 5 DVDs and 1 Video CD.  
⁄ Subtitle button [61]  
Press repeatedly to select one of the subtitle languages  
programmed on DVD or to turn the subtitles off.  
¤ Clear button [53, 54, 59, 61-63]  
* Program button [56-59]  
Works in conjunction with a number of player functions. Use to  
cancel repeat and random playback, and to edit programs.  
You can program titles, chapters or tracks to play back in desired  
order. Programs can be a maximum of 24 steps.  
‹ Random button [60]  
( Number buttons (1-9, +10, 0) [29, 51, 56-59, 78]  
Use to perform direct title/folder and chapter/track searches, and to  
input numerical values. Press Mode Rcvr for additional functions  
(see following page).  
Press to play chapters/tracks in random order.  
› Search/Enter button [52, 79]  
Press to perform a title/folder, chapter/track or elapsed time search.  
Press to confirm when controlling a connected TV.  
) +10/--/--- button [39, 78]  
Press to input numbers over 10.  
Press Mode Recvr to use the following (gray) buttons  
Other buttons have the same functions as when Mode DVD button is  
pressed.  
_ Standby button [34, 43, 45, 62]  
Put the DVD Receiver in standby.  
SP Setup  
Test Tone  
CH Sel  
3
6
7
1
SW Mode  
4
2
Distance  
5
1
2
3
4
5
+ Light button  
Illuminates the buttons. This button is useful when using the  
remote controller in dark locations. When pressed, the buttons on  
the remote controller light green.  
6
Up/Down  
9
-
IPM  
7
T D Setup  
8
8
+
10  
-- ---  
0
Search  
Enter  
¡ Clock button [41]  
/
Press to view the clock display.  
-
RC 507  
M
™ Display button [27, 36, 41, 63, 64]  
Press to change the information being displayed.  
1 SP Setup button [26]  
£ Menu button [32, 53, 61, 63]  
Press to select the optimum speaker configuration.  
Use to display or close the DVD menu or MP3 Navigator screen.  
2 SW Mode button [26]  
¢ VOL %/fi buttons [40]  
Press to select the subwoofer mode.  
For adjusting the volume.  
3 Distance button [27]  
∞ Setup button [30, 66]  
For setting the distances for each speaker.  
Press when the DVD Receiver is in either play or stop mode to  
open and close the Setup screen.  
4 IPM (Intelligent Power Management) button [25]  
Activates the IPM function.  
§ Muting button [40]  
Activates the mute function.  
5 T-D Setup [48, 49]  
For setting the T-D parameters.  
A. Control button [51]  
Press to change the acoustic mode to boost the super bass/high  
frequency sounds.  
6 CH Sel button [27, 28, 50]  
Selects a speaker for changing the speaker output level.  
• £ button [29, 32, 34, 52, 54-58, 60]  
7 Test Tone button [28, 50]  
Press to start or resume playback.  
Outputs a test tone for setting speaker levels.  
ª 1/¡ buttons [33, 35]  
8 Up/Down 5/∞ buttons [27, 28, 48, 50]  
During playback of DVD and Video CD, press ¡ to perform fast  
forward scanning or 1 to perform fast reverse scanning of DVD  
and Video CD. When a CD or MP3 is loaded, audio scanning is  
performed.  
Press to adjust the value.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index to Parts and Controls  
Rear panel  
1
2
3
4 5  
6
7
8
L
SURROUND  
SPEAKERS  
ANTENNA  
FRONT SPEAKERS  
CENTER  
AUDIOPREOUT  
AC INLET  
IR  
IN  
R
L
R
L
REMOTE  
ANTENNA  
CONTROL  
R
AM  
FM 75  
IN  
OUT  
MD/CDR/TAPE  
IN  
SUB  
WOOFER TV/LINE  
DIGITAL  
VIDEO OUTPUT  
Y
PB  
PR  
OPTICAL  
OUT  
IN  
S
VIDEO  
VIDEO  
COMPONENT  
9
0
Shapes of jacks vary depending on the area in which it was  
purchased.  
6 ANTENNA terminals [22, 23]  
These terminals are for connecting the FM antenna and AM  
antenna.  
1 SUB WOOFER PRE OUT jack [17, 18]  
This terminal is for connecting an active subwoofer.  
7 FRONT SPEAKERS, CENTER SPEAKER and SURROUND  
SPEAKERS terminals [18]  
2 TV/LINE IN jacks [16,19]  
Speaker terminals are provided for the front left, front right, center,  
This terminal is for connecting audio output terminals of TV, VCR or  
surround left and surround right speakers.  
other video equipment.  
8 AC INLET [24]  
3 MD/CDR/TAPE IN/OUT jacks [19]  
Connect supplied AC power cord to this terminal.  
These terminals are for connecting to the recording input and  
output terminals of an MD recorder, CD recorder or tape deck.  
9 DIGITAL OPTICAL IN/OUT jacks [16, 19]  
These are the digital audio input and output jacks. The digital input  
works in combination with the analog TV/LINE IN jacks. Connect  
the digital output from your TV or satellite tuner (MD player, etc.) to  
DIGITAL OPTICAL IN. Set the Input Selector to TV/LINE IN to play  
the digital sound. Connect the DIGITAL OPTICAL OUT to a digital  
recording device (MD recorder, CD recorder, etc.). Do not connect  
the DIGITAL OPTICAL OUT if the digital output from the same  
component is connected to the DIGITAL OPTICAL IN.  
4 z REMOTE CONTROL connector [20]  
Connect the Integra/Onkyo components that have z connectors  
such as a MD recorder, and cassette tape deck using the z  
cables provided with them. When these components are  
interconnected, they can be controlled from the remote controller  
provided with the DVD Receiver.  
After connecting the z connectors, check the operation of the  
remote controller buttons for use in controlling other components.  
0 VIDEO OUTPUT (VIDEO/S VIDEO/COMPONENT) jacks  
5 IR IN jack [21]  
[16]  
If the DSR-7.3 is located inside a rack or cabinet that will not allow  
infrared beams to reach the IR sensor, you will need to connect a  
remote sensor to IR IN jack to be able to use the remote controller.  
Then install the remote sensor in an unblocked location where you  
can easily point the remote controller.  
The monitor output includes RCA type, S video and component  
configurations. This output is for connecting television monitor or  
projector.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preparing the Remote Controller  
Inserting the Batteries  
Switching the remote controller  
function modes  
Some buttons on the remote controller have two or more  
functions. To set the functionality of these buttons, press one  
of the four Mode (DVD, Recvr, Tape, TV) buttons in advance.  
1
2
Detach the battery cover.  
Insert the two size AA/R6/UM3 batteries.  
Be sure to match the + and – ends of the batteries with  
the diagram inside the battery compartment.  
3
Attach the battery cover.  
The function mode remains the same until another Mode  
button is pressed.  
3
1
2
(Details about the functions and the related function modes  
are explained in each section.)  
Notes  
en  
• Do not mix new batteries with old batteries or different kinds of  
batteries.  
• To avoid corrosion, remove the batteries if the remote controller  
is not to be used for a long time.  
• Remove dead batteries immediately to avoid damage from  
corrosion. If the remote controller does not operate smoothly,  
replace both batteries at the same time.  
Se  
l
o
T
Mode buttons  
l
Step/Slow  
CH  
Tun  
ENTER  
VOL  
o
t
• The life of the supplied batteries is about six months but this  
varies depending on usage.  
T
-D/ST  
Muting  
Surround  
A.Control  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Pointing the remote controller in the  
right direction  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
Press Mode DVD first before operating the  
built-in DVD player.  
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
Point the remote controller toward the remote control  
sensor.  
/
RC-507  
M
Remote control sensor  
The SEND/  
o
T
e
LEARN indicator  
en  
is lit while any  
button on the  
remote controller  
g
Se  
o
T
e
is pressed.  
Press Mode Recvr first before operating the speaker setting  
and sound related operations.  
30˚  
o
30˚  
Press Mode Tape first before operating the z-connected  
Integra/Onkyo cassette tape deck, MD recorder or CD  
recorder (see pages 38, and 39).  
Notes  
• Place the unit away from strong light such as direct sunlight or  
inverted fluorescent light which can prevent proper operation of  
the remote controller.  
• Using another remote controller of the same type in the same  
room or using the unit near equipment which uses infrared rays  
may cause operational interference.  
• Do not put any object (such as a book) on the remote controller.  
The buttons of the remote controller may be pressed by mistake  
and drain the batteries.  
Press Mode TV first before operating your TV.  
To operate the TV with the supplied remote controller, you  
need to let the remote controller learn the TV remote control  
signals (see page 78).  
• Make sure the audio rack doors do not have colored glass.  
Placing the unit behind such doors may prevent proper remote  
controller operation.  
• If there is any obstacle between the remote controller and the  
remote control sensor, the remote controller will not operate.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to a TV  
Incomplete  
Before connecting  
• Connect the plugs securely.  
• Note that one audio/video connection  
cable and one S video connection cable  
are supplied.  
• Refer also to the instruction manual of the TV.  
• When you connect the DVD Receiver to the TV, be sure to turn  
off the power and unplug both the units from the socket before  
making any connections.  
• Connect the DVD Receiver to the TV directly. If you connect the  
DVD Receiver to a VCR, TV/VCR combination, or video selector,  
the playback picture may be distorted as DVD videos are copy  
protected.  
Insert completely  
I Connecting to a TV (or projector)  
Notes  
• Actual labels for component video inputs may vary depending  
on the TV manufacturer (ex. Y/CB/CR, Y/B-Y/R-Y, etc.).  
• In some TVs, the color levels of the playback picture may be  
reduced slightly or the tint may change. In such a case, adjust  
the TV for optimum performance.  
Using the supplied audio/video connection cable, make  
audio connections from the TV/LINE IN L and R jacks to  
the corresponding audio output jacks on the TV. In the  
same manner, make video connections from the VIDEO  
OUTPUT “VIDEO” jack to the corresponding video input  
jack on the TV.  
If your TV has a S video input jack and/or component video  
input jacks, make S video connection to the S VIDEO jack  
using supplied S video connection cable and/or make  
component video connection to the COMPONENT jacks  
using component video connection cable (not supplied).  
These connections allow you to enjoy higher quality picture  
playback. You can switch between [S1] and [S2] S-video  
output from the Setup menu on page 69.  
Video  
(Yellow)  
L (White)  
TV or projector  
Audio/video connection cable  
DIGITAL  
OUT  
OPTICAL  
R (Red)  
AUDIO  
OUT  
VIDEO S VIDEO  
COMPONENT VIDEO IN  
Y
PB  
PR  
IN  
IN  
R
L
S video connection cable  
Use the DIGITAL  
OPTICAL IN jack in  
Optical fiber cable  
Y
combination with the TV/  
LINE IN jack. When you  
use the Input selector to  
select TV/LINE IN,  
DIGITAL OPTICAL IN is  
also activated. When both  
a digital signal and an  
analog signal are input,  
the digital signal takes  
precedence.  
PB  
Component video  
connection cable  
PR  
Signal flow  
L
SURROUND  
ANTENNA  
FRONT SPEAKERS  
CENTER  
SPEAKERS  
AUDIOPREOUT  
AC INLET  
IR  
IN  
R
L
R
L
REMOTE  
CONTROL  
R
AM  
FM 75  
DO NOT connect the  
power cord at this time.  
IN  
OUT  
MD/CDR/TAPE  
IN  
SUB  
WOOFER TV/LINE  
DIGITAL  
VIDEO OUTPUT  
Y
PB  
PR  
OPTICAL  
OUT  
IN  
S
VIDEO  
VIDEO  
COMPONENT  
See “Turning the unit on/off with the TV’s power switch — IPM function” on page 25 for Inteligent Power Management (IPM) function.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting Speakers  
Before connecting  
• Refer also to the instruction manuals of the speakers.  
• This DVD Receiver is designed to reproduce optimum sound  
quality when speakers with the impedances specified below are  
connected. Please check the following information and choose  
speakers with appropriate impedances for the connections.  
Front speakers: 6 ohms min. per speaker  
Center speaker: 6 ohms min.  
Surround Speakers : 6 ohms min. per speaker  
• To prevent damage to circuits, never short-  
circuit the positive (+) and negative (–)  
speaker wires.  
• Do not connect the speaker cable to the L  
and R connectors at the same time and do  
not connect more than one speaker to the  
same speaker connectors.  
Connecting to SPEAKERS  
How to connect to the speaker connectors  
10 mm  
NO!  
NO!  
R
L
R
L
+
+
+
+
NO!  
–
–
–
–
Strip 10 mm from  
the end of each  
cable, then twist  
the exposed  
Press and hold  
the lever.  
Insert the stripped  
end of the cord.  
By releasing the  
lever, the lever is  
replaced.  
wires tightly.  
Front (R)  
Center  
Front (L)  
Active  
subwoofer  
– +  
– +  
– +  
L
SURROUND  
SPEAKERS  
ANTENNA  
FRONT SPEAKERS  
AUDIOPREOUT  
AC INLET  
IR  
IN  
CENTER  
R
L
R
L
REMOTE  
CONTROL  
R
AM  
FM 75  
IN  
OUT  
MD/CDR/TAPE  
IN  
SUB  
WOOFER TV/LINE  
DIGITAL  
VIDEO OUTPUT  
Y
PB  
PR  
OPTICAL  
OUT  
IN  
S
VIDEO  
VIDEO  
COMPONENT  
DO NOT connect the  
power cord at this time.  
Surround (R)  
Surround (L)  
– +  
– +  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Positioning Speakers  
I Standard speaker placement of the speakers system  
Speaker placement plays an important role in the reproduction of Surround sound. The placement of the speakers varies depending  
on the size of the room and the wall coverings used in the room. The illustration below shows an example of a layout for standard  
speaker placement. Refer to this example when you position the speakers in order to experience the best of Surround sound.  
For ideal Surround effects, all speakers should be installed.  
If a center speaker or subwoofer is not connected, the sound from the unused channel is properly distributed to the connected  
speakers in order to reproduce the best Surround sound possible.  
Front  
Front right  
Speaker  
Front left  
Speaker  
The center speaker reproduces a richer sound image by enhancing the  
perception of the sound's source and movement.  
Sub-  
woofer  
TV/Screen  
The left, right, and center speakers should face the seated listener and be  
placed at ear level.  
Front  
center  
Speaker  
Surround  
The surround speakers reproduce the feel of a moving sound while creating  
the sensation of being in the middle of the action.  
Place the left and right surround speakers 1 meter (3 feet) above the  
listener's ear level and facing toward the sides of the room, making sure that  
the listener is within the speakers’ dispersion angle.  
Subwoofer  
Install a subwoofer with a built-in power amplifier for powerful bass sounds.  
Place a subwoofer in the corner of a room or a similar position.  
Surround  
right  
Speaker  
Surround  
left  
Speaker  
Refer to the speakers’ instruction manuals for details.  
I Using the provided speaker labels  
The speaker terminals (+) of this unit are given different colors for ease of identification. By attaching the provided speaker labels to  
the speaker cables, the cables to be connected to the terminals can be identified easily.  
Attach the speaker label of each color to the speaker cable for the corresponding terminal and connect the speaker cable to the  
terminal having the same color as the label attached to the cable.  
The speaker terminals are colored as follows.  
Front left speaker (+):  
Front Right speaker (+):  
Center speaker (+):  
white  
red  
green  
blue  
gray  
Surround left speaker (+):  
Surround right speaker (+):  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to Audio/Video Equipment  
Incomplete  
Before connecting  
• Connect the plugs securely.  
• Refer also to the instruction manual of each component to be  
connected.  
• When you connect the DVD Receiver to audio/video equipment, be  
sure to turn off the power and unplug all the units from the socket  
before making any connections.  
• About the DIGITAL OPTICAL OUT/IN connectors  
Remove the protective caps before making  
Insert completely  
connections. When not in use, be sure to replace them.  
• Analogue audio from components connected to TV/  
LINE IN or MD/CDR/TAPE IN is not output from the  
unit’s DIGITAL OPTICAL OUT jack. Only digital audio playback from  
this unit is output from this jack.  
Caution  
When connecting this unit’s DIGITAL OPTICAL OUT jack to the digital in  
jack of a CD recorder or MD recorder, do not connect the CD or MD  
recorder’s digital output to this unit’s DIGITAL IN. A signal loop could be  
created which may damage the units.  
If you don’t connect TV audio output to this unit, you can  
connect MD player or BS tuner audio output.  
BS tuner,  
MD player, etc.  
CassetteTape Deck, MD Recorder,  
CD Recorder, etc.  
DIGITAL  
DIGITAL  
OUT  
OPTICAL  
AUDIO  
OUT  
AUDIO  
OUT  
AUDIO  
IN  
IN  
OPTICAL  
R
L
R
L
R
L
L
SURROUND  
SPEAKERS  
ANTENNA  
FRONT SPEAKERS  
CENTER  
AUDIOPREOUT  
AC INLET  
IR  
IN  
R
L
R
L
REMOTE  
CONTROL  
R
DO NOT connect the  
power cord at this time.  
AM  
FM 75  
IN  
OUT  
MD/CDR/TAPE  
IN  
SUB  
WOOFER TV/LINE  
DIGITAL  
VIDEO OUTPUT  
Y
PB  
PR  
OPTICAL  
OUT  
IN  
S
VIDEO  
VIDEO  
COMPONENT  
Audio connection cable  
Optical fiber cable  
Signal flow  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
z
Connection for the Integra/Onkyo Cassette  
Tape Deck, CD Recorder or MD Recorder  
The z terminal on the DVD Receiver is for connecting  
Integra/Onkyo MD recorder, CD recorder or Cassette tape  
deck equipped with the same z terminal. When an  
Integra/Onkyo component is z -connected, you can point the  
remote controller supplied with the DVD Receiver at the  
sensor on the DVD Receiver and operate that component  
without having to switch remote controllers. In addition, by  
connecting components to the z terminal, you can also  
perform the system operation given below.  
Power on/ready function  
When the DVD Receiver is in the standby state, if an z-connected  
component is turned on, then the DVD Receiver also turns on and  
the input source selected at this unit automatically switches to that  
component.  
Direct change function  
When the play button is pressed on an z-connected component,  
the input source selected at the this unit automatically changes to  
that component.  
Program Timer  
You can operate timer playback and recording using this unit.  
To connect components using the z terminal, simply connect  
a z cable from this z terminal to the z terminal of the  
other component. An z cable with a 3.5 mm (1/8 inch)  
miniature two-conductor plug comes with every cassette tape  
deck, compact disc recorder and MD recorder that has an z  
terminal.  
Sleep Timer  
You can fall asleep to a music/radio program using the timer.  
Power off function  
When the DVD Receiver is placed in the standby state, all z-  
connected components are automatically put in standby mode.  
Note  
Please change the name displayed by the input selector to match  
the connected component (see ‘Changing the “TAPE” display to  
match the connected source’ on page 38).  
Integra/Onkyo Cassette tape  
deck/CD recorder/MD recorder  
z cable  
L
R
ANALOG  
OUTPUT  
Be sure to connect  
using the audio  
connection cable.  
L
SURROUND  
ANTENNA  
FRONT SPEAKERS  
SPEAKERS  
AUDIOPREOUT  
AC INLET  
IR  
IN  
CENTER  
R
L
R
L
REMOTE  
CONTROL  
R
AM  
FM 75  
IN  
OUT  
MD/CDR/TAPE  
IN  
SUB  
WOOFER TV/LINE  
DIGITAL  
VIDEO OUTPUT  
Y
PB  
PR  
OPTICAL  
OUT  
IN  
S
VIDEO  
VIDEO  
COMPONENT  
Notes  
• Connect the plugs securely.  
• Be sure to connect to the z connectors using the z cable.  
• For remote control operation, the audio connection cables must  
also be connected.  
• If a component has two z terminals, you can use either one to  
connect to the DVD Receiver .  
• Do not connect the DVD Receiver’s z connector to any  
component other than an Integra/Onkyo product. It may cause  
malfunction.  
• Certain component models may not be able to control this unit.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Components not Reached by  
the Remote Controller Signals (IR IN)  
In order to use the remote controller to control the DVD  
Receiver from a remote location, you will need to prepare a  
multi-room kit (sold seperately) such as one if those given  
below:  
• Onkyo’s Multi-Room System kits (IR Remote Controller  
Extension System), or  
• Multiroom A/V distribution and control systems from Niles®  
and Xantech® to name a few.  
If the remote controller signal does not  
From the connecting block  
reach the DPC-5.3 remote sensor  
Mini plug cable  
L
SURROUND  
ANTENNA  
FRONT SPEAKERS  
CENTER  
SPEAKERS  
AUDIOPREOUT  
AC INLET  
IR  
IN  
R
L
R
L
REMOTE  
CONTROL  
R
AM  
FM 75  
IN  
OUT  
MD/CDR/TAPE  
IN  
SUB  
WOOFER TV/LINE  
DIGITAL  
VIDEO OUTPUT  
Y
PB  
PR  
OPTICAL  
OUT  
IN  
S
VIDEO  
VIDEO  
COMPONENT  
If the remote controller signal does not reach the DVD Receiver  
If the DVD Receiver is located inside a cabinet or other  
enclosure where the infrared rays from the remote controller  
cannot enter, then operation with the remote controller will not  
be possible. In such a case, it will be necessary to install a  
remote sensor at a location outside of the cabinet for the  
infrared rays from the controller to reach.  
The IR IN input allows you to control the DVD Receiver from  
the remote zone with the remote controller even though the  
remote zone may be on the other side of the building from the  
main zone. The diagram below shows how to make the prober  
connections for the remote zone.  
to IR IN  
IR Receiver  
Connecting  
block  
IR Receiver  
DSR-7.3  
IR IN  
Connecting  
block  
DSR-7.3  
Remote Controller  
Remote Controller  
In the  
cabinet  
Main room  
Remote zone  
: Signal flow  
: Signal flow  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Making Antenna Connections  
Connecting the Supplied FM and AM Indoor Antennas  
L
SURROUND  
SPEAKERS  
ANTENNA  
FRONT SPEAKERS  
CENTER  
AUDIOPREOUT  
AC INLET  
IR  
IN  
R
L
R
L
REMOTE  
CONTROL  
R
AM  
FM 75  
DO NOT connect the  
power cord at this time.  
IN  
OUT  
MD/CDR/TAPE  
IN  
SUB  
WOOFER TV/LINE  
DIGITAL  
VIDEO OUTPUT  
Y
PB  
PR  
OPTICAL  
OUT  
IN  
S
VIDEO  
VIDEO  
COMPONENT  
AM indoor antenna  
FM indoor antenna  
Insert into the hole.  
Press up and  
hold the lever.  
Insert the end of  
the cord.  
Release the lever to  
secure the connection.  
ANTENNA  
AM  
FM 75  
Adjusting the position of the FM indoor antenna  
Note  
Insert one end of the AM antenna cord  
to either of the AM antenna connectors  
and the other end to the other  
While listening to an FM program (see pag 35), extend the antenna and move it  
in various directions until the clearest signal is received, then secure the antenna  
with push pins in the position with the least distortion.  
connector. There is no difference  
between one end of the AM antenna  
cord and the other end, unlike the  
speaker cords which have positive and  
negative poles.  
Adjusting the position of the AM indoor antenna  
While listening to an AM program (see page 35), set the antenna in the direction  
and position where you receive the clearest sound.  
Put it as far away as possible from the unit, TVs, speaker cables, and power  
cords.  
Connecting an AM Outdoor Antenna  
Outdoor antenna  
AM indoor antenna  
An outdoor antenna will be more effective if it is stretched  
horizontally above a window or outside.  
Leave the supplied AM indoor antenna connected.  
Note  
To avoid the risk of lightning and electrical shock, grounding is  
necessary. Follow item 14 of the "Important Safeguards" on page 2 when  
you install an outdoor antenna.  
ANTENNA  
AM  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting an FM Outdoor Antenna  
If the FM reception is not very clear with the supplied antenna, connect an FM outdoor antenna instead of the indoor FM antenna .  
FM outdoor antenna  
Connecting coaxial cable to a 75/300 ohm antenna adapter (not supplied)  
1 Strip the end of the coaxial cable.  
3 Remove the transformer wire A  
from slit B and insert it into slit C.  
15 mm  
ANTENNA  
6
3
6
Slit B  
mm mm mm  
AM  
FM 75  
1/4 1/8 1/4  
in. in. in.  
5/8 in.  
Wire A  
Slit C  
Connecting 300 ohm ribbon  
wire to a 75/300 ohm  
2 With your fingernail or a small  
screwdriver, press the stoppers  
outward and remove the cover.  
4 Insert the end of the cable.  
5 Clamp it in place with pliers.  
antenna adapter*  
Loosen the screws and wrap  
the wire around these screws.  
Then tighten the screws with  
a screwdriver.  
4
5
Tighten  
Loosen  
6 Reinstall the cover.  
Notes  
• Install the antenna well away from tall buildings and in an area where FM stations can directly be received.  
• Keep the antenna away from noise sources (neon signs, busy roads, etc.).  
• It is dangerous to put the antenna close to power lines. Keep it well away from power lines, transformers, etc.  
• To avoid the risk of lightning and electrical shock, grounding is necessary. Follow item 14 of the “Important Safety Instructions” on page 2 when  
you install the outdoor antenna.  
Directional Iinkage  
Do not use the same antenna for both FM and TV (or VCR) reception since the FM and TV (or VCR) signals can interfere with each  
other. If you must use a common FM/TV (or VCR) antenna, use a directional linkage type splitter.  
Directional linkage  
type splitter  
To DVD Receiver  
To TV (or VCR)  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Power/  
Turning on the DVD Receiver  
Before connecting  
Standby/On  
• Make sure that all the connections from pages 16 to 23 are  
On indicator  
complete (the connection to the TV is required).  
Standby indicator  
Display  
• Turning on the DVD Receiver may cause a momentary power  
surge, which might interfere with other electrical equipment such  
as computers. If this happens, use a wall outlet on a different  
circuit.  
I Setting the Clock Display  
To display the clock while in Standby mode, hold down the  
Standby/On button for at least 2 seconds while the unit is in On  
mode.  
Connect the power cord to the AC  
INLET of the DVD Receiver.  
1
2
AC INLET  
Note  
Displaying the clock in Standby mode consumes the same amount of  
power as in the On mode.  
Connect the power cord to a wall  
outlet.  
The DVD Receiver enters the standby  
mode and the Standby indicator lights up.  
AC INLET  
to wall outlet  
Press Standby/On on the DVD  
Receiver or On on the remote  
controller to turn on the DVD  
Receiver.  
3
Unit  
The light and display on the DVD  
Receiver’s front panel light. At the same  
time, the Standby indicator goes off and  
the On indicator lights up.  
On indicator  
Remote  
Controller  
Standby indicator  
• To put the DVD Receiver in the standby  
mode, press Standby/On on the DVD  
Receiver, or Standby on the remote  
controller. Be sure to set the volume to  
minimum before putting the DVD  
Receiver in the standby mode for the  
next use to avoid sudden loud sound  
reproduction.  
• While in the Standby mode, the DVD  
Receiver can receive signals from the  
remote controller.  
• Setting the Standby button on the  
Remote controller to standby does not  
shut off the power completely.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Se  
o
Before operating the  
remote controller  
Press Mode Recvr.  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
T-D/ST  
Muting  
Surround  
A.Control  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
IPM  
+10  
-
0
Search  
Enter  
/
RC-507M  
I Turning the unit on/off with the TV’s power  
switch — IPM function  
The DVD Receiver is equipped with the Intelligent Power  
Management (IPM) system.  
Just turn on your TV’s power switch and, in about 5 seconds,  
the DVD Receiver turns on automatically. If you turn off the  
TV’s power switch, IPM indicator flashes on the display and  
the DVD Receiver automatically turns off in about 5 minutes.  
To activate the IPM function  
1 Connect the audio output of your TV’s audio output to the  
DVD Receiver’s TV/LINE IN L/R jacks (refer to page 16).  
2 Press IPM on the remote controller repeatedly to turn on  
the IPM indicator on the unit.  
IPM  
7
Theater-Dimensional  
IPM  
Notes  
• The IPM system may not function properly with some TV sets.  
• When using monaural TV, connect the audio output of the TV to  
the DVD Receiver’s TV/LINE IN L jack.  
• When the TV is turned off while the DVD Receiver selects other  
input source, the DVD Receiver does not turn off.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Speaker Setup  
Se  
o
You need to set up the speaker configuration for the speaker  
system connected to the SPEAKERS connectors  
(see page 17).  
Before operating the  
remote controller  
Press Mode Recvr.  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
T-D/ST  
Muting  
Surround  
A.Control  
Notes  
Repeat  
A-B  
• Speaker setup cannot be done if;  
– Headphones are connected (see page 40)  
• It is not necessary to set the parameters again once you have  
completed the setup unless you change the speaker  
configuration.  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
SP Setup  
SW Mode  
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507  
M
Selecting the number of speaker  
channels  
Selecting the Subwoofer mode  
Note  
To check the present setting while the normal display is displayed,  
press SP Setup once. To change the setting, press the button  
repeatedly within three seconds.  
Press SW Mode on the remote  
controller.  
Remote controller  
only  
SW Mode  
4
Remote controller  
Press SP Setup repeatedly to select  
only  
the number of channels for the  
With the first press of the button, you can  
check the present setting. Then each  
press of the button changes the subwoofer  
mode as follows (a tip on how to select the  
right subwoofer mode is in parentheses):  
SPEAKERS system.  
SP Setup  
1
SW Mode 1 (Factory setting)  
(When small–with limited bass signal  
handling–front speakers are  
connected)  
Pressing the button repeatedly within three  
seconds changes the number of channels  
as follows (the corresponding speaker  
configuration is described in parentheses):  
↓
SW Mode 2  
Speaker 5ch (Factory setting)  
(Front left, center, and right, plus  
(When large–wideband–front speakers  
are connected)  
surround left and right speakers)  
↓
↓
SW Mode 3  
Speaker 2ch  
(When large–wideband speakers are  
connected to all channel)  
(Front left and right speakers)  
↓
↓
Speaker 3ch  
SW Off  
(Front left, center, and right speakers)  
(When no subwoofer is connected)  
↓
Speaker 4ch  
(Front left and right, plus surround left  
and right speakers)  
The normal display resumes in three  
seconds.  
The normal display resumes in three  
seconds.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Se  
o
Display  
Before starting the procedure below, measure the distances  
from each speaker to the listening position.  
For pair speakers such as front left and right speakers, the  
distance from the listening position to one speaker should be  
the same as the distance to the other.  
Before operating the  
remote controller  
Press Mode Recvr.  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
T-D/ST  
Muting  
Surround  
A.Control  
Repeat  
A-B  
In the procedure below, select the values which approximate  
the actual distances.  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
CH Sel  
Up/Down  
6
Up/Down  
9
Distance  
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507  
M
Setting the Distance From the Listening Position to Each Speaker  
Press Distance.  
The distance entry display for the front left  
and right speakers appears.  
Press CH Sel, then press  
1
4
CH Sel  
3
Up/Down 5/∞ repeatedly to select  
the surround left and right speaker  
distance.  
Remote controller  
only  
Distance  
5
«
You cannot enter the following distances:  
• Distances longer than the distance set  
for the front speakers.  
• Distances shorter than the distance  
obtained by subtracting “15 ft. (4.5 m)”  
from the distance entered for the front  
speakers.  
6
Up/Down  
9
Press Up/Down 5/∞ to select the  
front left and right speaker  
distance.  
2
6
Up/Down  
9
Note  
If you selected a speaker configuration with no  
surround speakers on the opposite page, this  
step will be skipped.  
You can select a distance between 1 ft.  
and 30 ft. (0.3 m and 9 m).  
Distance  
5
Press CH Sel, then press  
Up/Down 5/∞ repeatedly to select  
the center speaker distance.  
Press Distance.  
The normal display resumes.  
CH Sel  
5
3
3
«
You cannot enter the following distances:  
I Changing the units of measurement  
• Distances longer than the distance set  
for the front speakers.  
6
Up/Down  
9
You can change the units of measurement while setting the  
distance. Press the Display button on the remote controller to select  
between meters and feet.  
• Distances shorter than the distance  
obtained by subtracting “5 ft. (1.5 m)”  
from the distance entered for the front  
speakers.  
a
Note  
If you selected a speaker configuration with no  
center speaker on the opposite page, this step  
will be skipped.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Speaker Setup  
Se  
o
Adjust each speaker’s relative volume balance so that the  
volumes of all speakers’ test tones sound equal at the  
listening position.  
Before operating the  
remote controller  
Press Mode Recvr.  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
T-D/ST  
Muting  
Surround  
A.Control  
Note  
You cannot adjust the volume balance while the muting function is  
Repeat  
A-B  
activated.  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
CH Sel  
Up/Down 5/∞  
Test Tone  
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507M  
Adjusting Each Speaker's Relative Volume Balance – Test Tone  
Press Test Tone.  
When you have completed the  
adjustment by repeating step 2,  
press Test Tone.  
The test tone stops and the normal display  
resumes.  
When test tone adjustments are  
completed, return the volume to its usual  
level.  
1
3
Test Tone  
2
Each speaker emits the test tone (pink  
noise) and the display shows the speaker  
emitting the test tone in the following  
order:  
Remote controller  
only  
Test Tone  
2
LEFT  
(Front left ch.)  
→
CENTER  
(Center ch.)  
↓
↑
Note  
SUBWFR  
(Subwoofer)  
↑
RIGHT  
Even if you don’t press Test Tone, the test tone  
will stop after two minutes.  
(Front right ch.)  
↓
SURR R  
(Surround right ch.)  
SURR L  
←
(Surround left ch.)  
Set voume at a level for easy comparison  
of all speakers’ output.  
Note  
No test tone will be emitted from a speaker  
which is not included in the speaker  
configuration on pages 26 even if it is actually  
connected.  
Press CH Sel repeatedly to select  
the speaker, then press  
Up/Down 5/∞ to adjust the volume  
level.  
2
CH Sel  
3
The volume level can be adjusted between  
–12dB and +12dB.  
«
6
Up/Down  
9
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Getting Started Using Your  
DVD Receiver  
en  
Open/Close 0  
Se  
o
Step/Slow  
Before you can start to enjoy the digital audio and video  
CH  
Tun  
ENTER  
VOL  
Before operating the  
remote controller  
Press Mode DVD.  
2/3/5/∞  
ENTER  
on DVDs, be sure that you have either performed the  
Setup Navigator procedure described in the previous  
section or made the necessary settings in the Setup  
screen menus as outlined in the next section to set up  
the DVD receiver to correspond to your home system.  
Having made these settings, you are now ready to start  
using the DVD receiver to enjoy DVDs, Video CDs, CDs  
and MP3s.  
T-D/ST  
Muting  
Surround  
A.Control  
£
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- --  
0
Search  
Enter  
/
RC-507  
M
VCD  
CD  
MP3  
DVD  
Disc tray  
I About the  
,
,
and  
marks in  
the pages related to disc operation  
DVD  
VCD  
CD  
means the function or title is related to DVD-Video operation.  
means the function or title is related to Video CD operation.  
means the function or title is related to audio CD operation.  
means the function or title is related to MP3 operation.  
Open/Close  
MP3  
Pause Play  
DVD  
VCD  
CD  
MP3  
Playing DVDs, Video CDs, CDs and MP3s  
Remote  
controller  
Unit  
Press Open/Close on the unit or  
Select the item you want to view.  
Before operating the remote controller,  
press Mode DVD.  
1
4
Open/Close 0 on the Remote  
controller.  
The disc tray comes out.  
ENTER  
• When a DVD is loaded:  
Select the item with the cursor buttons  
(2/3/5/∞) or the number buttons then  
press ENTER.  
Remote  
controller  
• When a Video CD is loaded:  
SP Setup  
Test Tone  
CH Sel  
1
2
Distance  
5
3
Use the number buttons to select the  
item.  
SW Mode  
4
6
Up/Down  
9
-
IPM  
7
T
D Setup  
8
Load a disc.  
+
10  
-- ---  
0
/
Load a disc with the label side facing up,  
using the disc tray guide to align the disc.  
2
Notes  
• The TV screen size is factory set to present the wide screen  
format (16:9 aspect ratio). If you have a standard TV screen (4:3  
aspect ratio), this setting can be changed to match your TV  
screen size in the Video 1 menu (page 68).  
• Do not move the DVD receiver during playback. Doing so may  
damage the disc.  
• Use Open/Close on the DVD receiver or 0 on the Remote  
controller to open and close the disc tray. Do not touch the disc  
tray while it is moving. Doing so may cause the DVD Receiver to  
malfunction.  
• Do not press down on the disc tray or put any objects other than  
playable discs on the disc tray. Doing so may cause the DVD  
Receiver to malfunction.  
Press Play on the unit or £ on the  
3
Unit  
Remote controller.  
• The disc tray closes, and playback  
begins.  
• MP3 only: It may take a few seconds for  
the DVD Receiver to locate the track on  
the disc, depending on the complexity  
of the file structure.  
Remote  
controller  
• Depending on the disc, a menu may be  
displayed. If a menu is displayed,  
proceed to step 4.  
• In many instances, a menu screen appears when playback of a  
movie is complete. Prolonged display of an on-screen menu may  
damage your television set, permanently etching that image onto  
its screen. To avoid this, be sure to press Stop on the unit or 7  
on the Remote controller once the movie is complete.  
• To pause playback, press Pause on the  
unit or on the Remote controller. To  
resume playback, press Pause/ or  
Play/£.  
I When an operation is prohibited  
There are times when you are using the DVD Receiver and  
attempt to perform an operation, but for some reason it cannot  
be performed. When this occurs, one of the two following  
icons appears on the screen.  
Play indicator  
Pause indicator  
The operation is prohibited by the DVD Receiver.  
The operation is prohibited by the programming on the  
disc.  
Inserted disc indicator (DVD, CD, VCD)  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Getting Started Using Your DVD Receiver  
The Setup Navigator has been designed to simplify the  
process of getting the DVD Receiver ready to perform.  
Designed as a series of on-screen multiple-choice questions,  
the Setup Navigator automatically sets the video and  
language settings according to how the questions are  
answered. Once this procedure is complete, it will be possible  
to begin using the DVD Receiver to enjoy DVDs.  
The procedure on this page describes the operations  
necessary to function within the Setup Navigator screens. A  
detailed description of the contents of each question that  
appears on the screen can be found on the following pages.  
Using the Setup Navigator  
I When setting up for the first time  
Press Setup/TV Input.  
1
2
3
Some DVDs start playing automatically when loaded in the  
DVD Receiver. Because the Setup Navigator cannot be used  
if a disc is playing, it is recommended to set up the DVD  
Receiver using the Setup Navigator before loading a DVD for  
the first time. If a DVD has been loaded, be sure to press 7  
before proceeding.  
u
When Setup/TV Input is pressed for the  
first time, the following screen appears.  
Though the Setup Navigator may be used  
more than once, this screen only appears  
the first time Setup/TV Input is pressed.  
V2 Language General  
Video1  
I To change the answer to a prior question  
Setup Navigator  
Use the cursor button (2) to return to previous screens.  
Please note, however, that you cannot go forward using the  
cursor button (3), so it will be necessary to answer all the  
questions that occur after the screen that was returned to.  
Setup Navigator  
Start  
Auto Start Off  
Setup using the Setup Navigator  
ENTER  
SETUP  
Move  
Select  
Exit  
I To exit the Setup Navigator  
Press Setup/TV Input while on any of the screens to exit the  
Setup Navigator. Please note that if the Setup Navigator is  
exited before all the questions are answered, no settings are  
changed.  
Use the cursor buttons (5/∞) to  
make a selection.  
• If you are going to use the Setup  
Navigator, it is not necessary to change  
the setting on the first screen. Please  
proceed to the next step.  
ENTER  
Note  
• On-screen information ( ) appears to clarify the functions and  
i
explain the options available.  
• If you do not want to set up the DVD  
Receiver using the Setup Navigator,  
use the cursor button (∞) to select [Auto  
Start Off] at this time.  
The Setup Navigator function may still  
be used at a later time in manual Setup  
screen menu operation (page 66).  
• If the input is not set to DVD the screen will not appear, even if  
you press the Setup/TV Input button. In that case, press Mode  
DVD, 0 or £ to set the input to DVD.  
Press ENTER.  
The selection is entered and the next  
Setup Navigator screen appears.  
ENTER  
Use steps 2 and 3 as a basis for entering  
selections on the all of the Setup Navigator  
screens described on the following pages.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Sel  
o
l
2/3/5/∞  
ENTER  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
t
T-D/ST  
Muting  
Setup/  
Surround  
A.Control  
TV Input  
7
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
Number  
buttons  
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507M  
I Setting the OSD Language  
Note  
There are two screen formats that can be used to display  
(On-Screen Display Language)  
wide-screen format DVDs: letter box and pan & scan. When  
[Standard (4:3)] is selected in the Setup Navigator, the letter box  
screen format is automatically selected. To switch the preference to  
the pan & scan format, make changes in the Setup screen Video 1  
menu [TV Screen] setting (page 68).  
The [OSD Language] screen establishes the OSD language,  
or on-screen display language, which refers to the language  
that is used by the DVD Receiver in menus and on-screen  
messages. Additionally, the language that is established at  
this setting will also be used for the default audio and subtitle  
language.  
I Confirming the settings  
The [Exit Setup Navigator] is the final screen in the Setup  
Navigator.  
V2 Language General  
Video1  
Setup Navigator  
English  
français  
Deutsch  
Italiano  
Español  
Language  
OSD Language  
V2 Language General  
Video1  
Setup Navigator  
Select the On Screen Language  
Save Changes  
Exit Setup Navigator  
Delete Changes  
Start Again  
ENTER  
SETUP  
Move  
Select  
Exit  
Changes are saved  
Settings: English (Factory setting)  
ENTER  
SETUP  
Select  
Exit  
Move  
français  
Deutsch  
Italiano  
Español  
Settings: Save Changes (Factory setting)  
Select to have the DVD Receiver make all of the  
necessary video and language settings according  
to your responses in the Setup Navigator.  
Notes  
• The languages that can be selected may be different from those  
shown above.  
Delete Changes  
Select to exit the Setup Navigator without changing  
any of the system settings.  
• In addition to setting the [OSD Language], the audio and subtitle  
language are also set at this time. If you wish to change the  
audio or subtitle language to a different language, make changes  
in the Setup screen Language menu [Audio Language] and  
[Subtitle Language] as needed (pages 73, 74).  
Start Again  
Select to return to the [OSD Language] screen of  
the Setup Navigator and do the settings again.  
I To change other DVD receiver settings in  
I Setting the TV screen size  
the Setup screen menus  
The procedure for changing the settings in the Setup screen  
menus is described on page 66.  
The [TV Type] screen establishes the size, or more  
appropriately the width to height ration of your television or  
monitor. The width-to-height ratio of conventional TVs is 4:3,  
while the width-to-height ratio of wide screen and high-  
definition TVs is 16:9. This width-to-height ratio is called the  
aspect ratio.  
V2 Language General  
Video1  
Setup Navigator  
TV Connection  
TV Type  
Widescreen(16:9)  
Standard(4:3)  
Widescreen TV  
16:9 aspect raito  
SETUP  
ENTER  
Move  
Select  
Exit  
Settings:Widescreen (16:9) (Factory setting)  
Standard (4:3)  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Getting Started Using Your DVD Receiver  
DVD  
DVD  
VCD  
VCD  
When a Menu Screen is Displayed  
To Open or Return To the DVD or Video  
CD Menu Screen  
Although this differs depending on the disc, pressing Menu,  
Top Menu, or Return during DVD playback or Return during  
Video CD playback displays the menu screen. Refer to the  
DVD or Video CD disc jacket and accompanying  
documentation for more information.  
Menu screens are displayed for DVDs that have menu  
screens or Video CDs that include Playback Control (PBC).  
DVDs often contain extra information that can be accessed in  
the DVD menu and sometimes makes navigating DVD menu  
screens as enjoyable as watching the feature presentation.  
Example: When a DVD that has menu screens is loaded  
I To play Video CDs without displaying menu  
1 Highlight Clips  
2 Chapter List  
screens  
3 Commercial Header  
4 Subtitles  
5 Soundtrack  
Video CDs with Playback Control (PBC) display a menu  
screen when play is started. It is possible, however, to play  
back Video CDs without displaying menu screens.  
When a Video CD with PBC is loaded, press 7, and then the  
number button of the track you want to play.  
6 Start Main Feature  
Example: When a Video CD that has Playback Control is  
loaded  
I When screen saver appears  
During disc playback, when the disc is paused, a screen saver  
STANDARD VOCAL BEST  
1
2
3
4
5
6
7
8
Don't Tekno for an Answer  
Bad Whack Naff Riff  
dubmyheadbassman  
Gooey Love Jingle  
Praise the Day  
Bertie B.& the Goans  
Hood in the Boyz  
Sleek Machine  
Philip William  
Formerly an Artist  
Pfeuti  
appears after a fixed period. Press  
or £ to resume  
playback. Alternately, the unit can be programmed to turn off  
at this time (page 69).  
G3, Ba-san  
Abstract Jazz Phunk  
Rock the Love Jive  
John Torn  
Hot Monkey Stick  
CD’s may be played with TV screen on or off.  
I To navigate a menu screen  
• Although individual DVD titles may differ, when a menu  
screen is displayed, use the cursor buttons (2/3/5/∞) and  
ENTER on the remote control. The cursor buttons are used  
to move around the options on the screen and ENTER is  
used for selection.  
• Occasionally, the number buttons may also be used to  
make selections. If this is possible, using number buttons  
serves to directly select an option on a menu screen. Only  
number buttons are used to make selections on Video CD  
menu screens.  
• When the Video CD has more than one menu, pages can  
be advanced to or returned to with 4 or ¢.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Sel  
o
l
Top Menu  
Return  
Menu  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
2/3/5/∞  
ENTER  
£
7
t
T-D/ST  
Muting  
Surround  
A.Control  
4/¢  
1/¡  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
4/¢  
Play  
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- -  
0
Search  
Enter  
/
RC-507M  
DVD  
DVD  
VCD  
CD  
MP3  
VCD  
CD  
MP3  
Chapter (Track) Skip Forward/Skip  
Back  
Forward and Reverse Scanning  
Remote controller Fast forward and reverse scanning  
Remote controller  
Advancing to the next chapter (track)  
Press and hold 1/¡ (4/¢ on  
the front panel) during playback to  
scan forwards or backwards.  
While “¡ 1” or “1 1” is displayed on-  
screen blinking, release the button to  
Press ¢.  
Press to skip forward to the next chapter  
(track).  
Unit  
Skipping back to the previous chapter  
(track)  
resume normal playback.  
Unit  
Variable speed scanning (Remote  
controller only)  
Press 4.  
• Press once to skip back to the start of  
the chapter (track) currently playing.  
1 Press (but don’t hold) ¡ or 1  
during playback to start scanning.  
• Press twice to skip back to the start of  
the previous chapter (track).  
“¡ 1” or “1 1” appears on screen.  
2 Depending on the type of disc  
playing, you can increase the  
scanning speed by pressing ¡  
or 1.  
The scan speed is shown on-screen.  
DVDs have three scanning speeds;  
1 ↔ 2 ↔ 3  
CD and Video CDs have two scanning  
speeds;  
1 ↔ 2  
MP3 have only one scanning speed.  
3 Press Play on the unit or £ on  
the remote controller to resume  
normal playback.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Open/Close  
Se  
l
Standby  
Getting Started Using Your DVD Receiver  
o
Step/Slow  
CH  
Tun  
ENTER  
VOL  
T-D/ST  
Muting  
Surround  
A.Control  
Standby/On  
£
Repeat  
A-B  
7
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
Open/Close  
Stop Play  
+10  
-- ---  
0
Search  
Enter  
/
RC-507  
M
DVD  
DVD  
VCD  
VCD  
CD  
MP3  
Resuming playback from where you  
stopped  
Stopping Playback and Switching  
Power Off  
Use the resume feature to restart playback from the point that  
the disc was stopped last.  
This features cannot be used with MP3s and CDs.  
Press Stop on the unit or 7 on the  
1
remote controller .  
Remote controller  
Playback stops.  
Press Stop on the unit or 7 on the  
1
remote controller once.  
Remote controller  
The display shows “STOP” then  
“RESUME”, and the stop position is  
memorized.  
Unit  
• The resume position remains  
memorized as long as the disc is in the  
DVD Receiver — even if you switch the  
Unit  
power off.  
• Pressing Stop/7 twice causes the disc  
to return to the beginning when Play/£  
is pressed again. The display shows the  
disc type (DVDs or Video CDs).  
Press Open/Close/0 on the Remote  
controller or Open/Close on the  
unit.  
2
Remote controller  
The disc tray comes out.  
Press Play on the unit or £ on the  
2
remote controller .  
Remote controller  
Unit  
Playback starts from the resume position.  
Unit  
Remove the disc.  
3
Notes  
Press Standby on the remote  
controller or Standby/On on the  
unit.  
• The actual restart position may be slightly before or after the  
resume position.  
• If you want to remove the disc but still want to resume playback  
from the last stopped position, use the Last Memory feature  
instead (page 62).  
4
Remote controller  
The disc tray goes back in.  
• The memorized resume position is erased when you open the  
disc tray, or change the Parental Lock Level setting (page 76) or  
On-screen Display (OSD) setting (page 72).  
Unit  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Listening to the Radio  
Se  
o
Input Selector 2/3  
l
There are two ways to select radio stations:  
• Manual tuning  
Before operating the  
remote controller  
Press Mode Recvr.  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
• Presetting radio stations then selecting the preset  
t
T-D/ST  
Muting  
Surround  
A.Control  
channels  
Input 2/3  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
Preset Memory  
/
RC-507  
M
Tuning/Preset 2/3  
Tuning in a weak frequency (only for FM stations)  
When you tune in a stereo FM station, the FM STEREO indicator  
lights up if the signal is sufficiently strong.  
Tuning Manually  
Unit  
Press Input 2/3 on the unit or  
Input Selector 2/3 on the remote  
controller repeatedly to select the  
band (FM or AM).  
1
If the signal is weak, you may not be able to tune to the station.  
In this case, press FM Mode on the remote controller.  
The FM STEREO indicator and AUTO goes off. Then select the  
station to which you want to listen. (At this time, the station will be in  
mono and interstation noise will be heard.)  
e.g. When FM is selected.  
Remote  
controller  
Remote controller  
FM Mode  
Sel  
Press and holdTuning/Preset 2/3  
on the unit for about 1 second.  
Unit  
Presetting Radio Stations  
2
You can preset up to 30 AM and FM stations.  
Tune in the radio station you wish  
1
• When the band is FM  
Auto tuning starts. The frequency  
changes in 50 kHz steps.  
to preset (see steps in the left  
column of this page).  
When a broadcast is received, scanning  
stops and the frequency flashes in the  
display.  
Unit only  
Press Preset Memory.  
2
The preset number starts flashing in the  
display.  
• When the band is AM  
The frequency changes In 10 kHz steps  
When you release the button, the frequency  
stops changing and flashes in the display.  
While the frequency is flashing (for  
about 5 seconds), press  
Tuning/Preset 2/3 on the unit to  
change the frequency.  
Unit only  
(Within about 8 seconds), press  
Unit  
3
3
Tuning/Preset 2/3 on the unit to  
select the preset number.  
• The frequency changes each time you  
press the button.  
• You can change the frequency as long  
as the frequency in the display is  
flashing. Each press of either button  
causes the frequency to flash for about  
5 seconds.  
Unit only  
Press Preset Memory.  
4
The radio station is registered to the  
preset channel.  
To register another preset station, repeat  
steps 1 to 4.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Listening to the Radio  
Se  
o
Display  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
ENTER5/∞  
T-D/ST  
Muting  
Surround  
A.Control  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
--  
0
Search  
Enter  
/
RC-507  
M
Preset Memory  
Select the station you wish to  
name.  
FM Auto Preset Memory  
1
2
See “Selecting preset stations” on page 37.  
This function enables you to store the frequencies into  
memory automatically, without having to go through and  
store each frequency manually.  
Hold down the Preset Memory  
1
button for a few seconds. “AUTO  
Press the Display button on the  
remote controller for at least 2  
seconds.  
The DVD Receiver enters character input  
mode, “NAME IN” appears on the display, then  
“.....” flashes on the display.  
MEM” will start flashing on the  
display. Keep holding down the  
button for a few more seconds to  
a
Hold down  
start the Auto Memory function.  
«
The frequencies are scanned from low to high.  
Up to 20 FM stations with the best signal  
quality are selected, sorted in order from low to  
high frequency, and stored into the preset  
memory. Even if you have already preset more  
than 10 AM stations, you can only store up to  
30 AM/FM stations total.  
Use the Cursor 5/∞ buttons to  
select a character and press the  
ENTER button to store the  
character.  
Flashing “.....” mark appears next to the stored  
character.  
3
ENTER  
Note  
All FM stations previously stored in memory will be replaced with  
Repeat step 3 to store more characters. You  
can enter characters in any positon by moving  
the cursor with the Cursor 2/3 button. You can  
store up to 8 characters.  
When 8 characters have been entered,  
“COMPLETE” appears on the display. To enter  
less than 8 characters, press ENTER  
repeatedly to move the cursor to the end, or  
hold down the Display button for more than 2  
seconds.  
new Auto Memory stations.  
Naming a Preset Station  
You can name the preset stations so that the name, instead  
of the frequency, appears on the display when you select the  
station. The following 52 characters can be used:  
(space) ABCDEFGHIJKLMNOPQUSTUVWXYZ” ’&()[ ]*+,-./  
=?0123456789  
Tip  
To change an entered name, follow the steps above. In step 3, use  
the Left/Right Cursor buttons 2/3 to select the name you want to  
change. Change the letters of the name one at a time. To delete a  
letter, select the blank space (_). You cannot delete the whole name  
at once.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Se  
o
Input Selector 2/3  
Tun +/–  
l
Step/Slow  
CH  
Tun  
ENTER  
VOL  
Before operating the  
remote controller  
Press Mode Recvr.  
t
T-D/ST  
Muting  
Surround  
A.Control  
Input 2/3  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
Preset Memory  
Tuning/Preset 2/3  
/
RC-507  
M
Selecting Preset Stations  
Erasing a Preset Station  
Before selecting preset stations, you need to preset the radio  
stations. See “Presetting Radio Stations” on page 35.  
Select the preset channel you wish  
to erase (see steps in the left  
column of this page).  
1
2
Press Input Selector 2/3 on the  
remote controller or Input 2/3 on  
the unit to switch the input source  
to the FM or AM.  
Remote  
1controller  
Unit only  
Sel  
Press Preset Memory.  
“ERASE” appears in the display.  
The band selected in this step will not  
affect the next step.  
Unit  
While “ERASE” is flashed (for  
about 8 seconds), press Preset  
Memory again.  
3
The selected preset channel will be  
erased.  
Remote  
controller  
Press Tuning/Preset 2/3 on the  
unit or Tun+/– on the remote  
controller repeatedly to select the  
preset number of the desired radio  
station.  
2
Step/Slow  
Various Functions While Listening to  
Radio Programs  
CH  
Tun  
To use the following functions, see page 40.  
• Adjusting the Volume  
• Muting the Sound  
• Listening Through Headphones  
• Controlling the Brightness of the display on the DVD Receiver  
Unit  
Note  
If you press Tuning/Preset 2/3 on the  
unit for more than 1 second, the unit  
enters the manual tuning mode. See step  
2 in “Tuning Manually” on page 35.  
Enjoying the Sound Effects While  
Listening to Radio Programs  
See page 46.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Se  
o
Playing the Connected Source  
Input Selector 2/3  
Input 2/3  
l
This section shows you how to play the  
sources connected to the DVD Receiver.  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
t
T-D/ST  
Muting  
Surround  
A.Control  
You may need to see “Connecting to a TV”  
on pages 16 and “Connecting to Audio/Video  
Equipment” on page 19 while following the  
steps in this section.  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
Preset Memory  
+10  
-- ---  
0
Search  
Enter  
/
RC-507  
M
About digital sound  
Press Input Selector 2/3 on the  
remote controller or Input 2/3 on  
the unit to select one of the  
following input sources:  
Remote  
controller  
1
2
If the equipment is digitally connected to the DVD Receiver,  
the sound from the digital input will automatically be selected  
and reproduced instead of the analog sound as explained  
below.  
• When the TV source is selected, the digital sound from the  
DIGITAL OPTICAL INPUT jack is reproduced.  
Sel  
• TV  
• TAPE/MD/CDR  
The selected input source appears in the  
multipurpose display. Also the input  
source indicator is lit in the display until  
the DVD Receiver is switched to another  
input source.  
Unit  
When the digital sound is reproduced, the DIGITAL indicator  
lights up in the display. According to the received sound  
system, the ŸDIGITAL or DTS indicator lights up.  
ŸDIGITAL DTS  
e.g. When TAPE is selected.  
Note  
Start playing the selected source.  
The DVD Receiver only reproduces DOLBY DIGITAL, DTS, and  
PCM sound formats from connected equipment.  
Various Functions While Playing the  
Connected Source  
Changing the “TAPE” display to match the  
connected source  
Press the Input 2/3 button on the unit to select TAPE.  
Press the Preset Memory button. “NAME SEL” is displayed then  
“TAPE” flashes in the display.  
Press the Input 2/3 button repeatedly to select the desired  
operation.  
To use the following functions, see page 40.  
• Adjusting the Volume  
• Muting the Sound  
• Listening Through Headphones  
• Controlling the Brightness of the display on the DVD Receiver  
1
2
3
The display changes as follows:  
TAPE→MD→CDR→TAPE  
Press the Preset Memory button to select. “COMPLETE” appears  
then the display switches back to the selected input.  
Enjoying the Sound Effects While  
Playing the Connected Source  
4
See page 46.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating the Integra/Onkyo Cassette Tape Deck/MD Recorder/CD Recorder With the  
Supplied Remote Controller  
Operating the Integra/Onkyo cassette tape deck, MD recorder or CD recorder to the DVD Receiver  
with the z cable (see page 20)  
Point the remote controller toward the DVD Receiver when you want to operate this equipment.  
When connecting the CD Recorder, use the Input Selector to select CDR (see page 38). Selecting CDR enables you too use the  
CDR function.To connect the MD recorder, follow the same procedure and select MD.  
Before operating the  
remote controller  
Press Mode Tape  
en  
Cassette tape deck  
CD recorder  
On  
On/Standby  
On/Standby  
Play  
On  
On/Standby  
On/Standby  
Play  
On  
Standby  
Se  
o
Standby  
Standby  
e
Tape  
£
£
Display  
7
Stop  
7
Stop/Cancel  
Pause  
Reverse play (reverse tape  
deck only)  
4
Down  
4
Rewind  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
¢
Up  
¢
Fast forward  
1
Fast Reverse  
Fast Forward  
Repeat mode  
Random play  
Change display  
Memory  
Repeat  
Selects reverse mode  
(ex. “, [, ”)  
¡
-
T
D/ST  
Muting  
Surround  
A.Control  
Repeat  
Random  
Display  
Program  
Clear  
4/¢  
MD recorder  
1/¡  
On  
On/Standby  
On/Standby  
Play  
-
B
Repeat  
A
Repeat  
A-B  
Standby  
Clear  
Late Night  
Audio  
Timer  
£
0–9, +10 (--/---) Number buttons  
Angle  
Subtitle FM Mode  
7
Stop/Cancel  
Pause  
FM Mode  
Clear  
FM Mode  
Play mode (random,  
program, normal)  
Last M  
Program Random  
Clear  
Program  
Random  
4
Down  
SP Setup  
1
SW Mode  
Test Tone  
CH Sel  
2
3
¢
Up  
Distance  
Number  
buttons  
4
IPM  
7
5
6
Up/Down  
9
-
T
1
Fast Reverse  
Fast Forward  
Repeat mode  
Random play  
Change display  
Memory  
D Setup  
8
¡
+
10  
-- ---  
0
Search  
Enter  
/
Repeat  
Random  
Display  
Program  
Clear  
-
RC 507  
M
Clear  
0–9, +10 (--/---) Number buttons  
FM Mode  
Play mode (random,  
program, normal)  
Notes  
• You can use grayed buttons in the illustration to control the DVD Receiver in any mode.  
• Some buttons may not work properly.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Various Functions Common to all  
the Sources  
Se  
o
Dimmer  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
VOL %/fi  
t
T-D/ST  
Muting  
Surround  
A.Control  
Muting  
Repeat  
A-B  
Master Volume  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507M  
Phones jack  
Adjusting the Volume  
Listening Through Headphones  
The volume of the front left and right, center, surround left  
and right, and subwoofer speakers will be adjusted at the  
same time.  
Connect the plug of the stereo headphones to the  
Phones jack on the DVD Receiver.  
When headphones are connected, you can adjust the  
volume of the sound through the headphones.  
The volume can be adjusted from 0 (min) – 80 (max) (the  
maximum volume changes depending on the Test Tone and  
Ch Sel settings).  
Operating with the remote controller  
Press VOL %/fi.  
VOL  
Notes  
• The speakers will not reproduce sound while headphones are  
connected.  
• The listening mode is set to “STEREO” after connecting the  
headphones to the Phones jack.  
• When you disconnect the headphones, the listening mode returns  
Operating with the unit  
to the previous mode.  
Turn Master Volume clockwise to  
increase the volume, or  
counterclockwise (anticlockwise)  
to decrease the volume.  
Controlling the Brightness of the  
display on the DVD Receiver  
Muting the Sound  
Remote  
controller only  
Press Muting.  
“MUTING” appears in the multipurpose  
display for about three seconds. Also the  
MUTING indicator flashes in the display  
during the muting mode.  
Remote  
controller only  
Press Dimmer.  
Each press of the button changes the  
Muting  
brightness as follows:  
The display becomes dimmer.  
↓
The display is dimmest.  
↓
The display resumes the original  
brightness.  
To restore the sound, press Muting again.  
Tip  
If you turn off the unit during muting, and turn it on again, the sound  
will be restored.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Using the Timer Functions  
Se  
o
This manual uses the 24-hour display to  
describe how to set the clock. The clock  
display may also be switched to a AM/PM  
display.  
Clock  
Display  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
t
T-D/ST  
Muting  
2/3/5/∞  
ENTER  
Surround  
A.Control  
Caution  
Repeat  
A-B  
• In the event of a power outage, or the power cord  
being removed from the socket, the clock display  
will disappear. Please reset the time again.  
• When using the clock functions, make sure that the  
power cord is connected to a proper power supply.  
Late Night  
Audio  
Timer  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507M  
Setting the current date and time  
Timer  
Press Timer repeatedly until  
Start the clock.  
1
5
“CLOCK” appears in the display on  
Match the date, time etc. then press  
ENTER. The display switches back to the  
function.  
the unit, then press ENTER.  
ENTER  
«
ENTER  
Blinking  
«
Press the cursor buttons (5/∞) to  
select a day of the week, then press  
ENTER.  
Display switches back to the function.  
2
While the desired day of the week is  
flashing, press ENTER.  
ENTER  
I Displaying the current time  
Press Clock on the remote controller.  
If the clock is not set, “ADJUST” flashes. Please set the  
clock.  
«
When the power on, press Clock on the remote control to  
display current date and time. Press Clock again to return to  
the previous display.  
Days of the week are displayed as follows:  
ENTER  
SUN (Sunday)  
THU (Thursday)  
FRI (Friday)  
SAT (Saturday)  
MON (Monday)  
TUE (Tuesday)  
WED (Wednesday)  
When the unit is in standby mode, press Clock on the remote  
control to display the current date and time. The display will  
disappear after 7 seconds. (Power saving mode)  
To switch the clock display 24-hour/  
AM/PM, press Display.  
3
4
a
«
j
Press the cursor buttons (5/∞) to  
Display disappears after 7 seconds  
set the time.  
ENTER  
Tip  
When using the 24 hour display, if you first  
press Mode DVD, you can also use the  
number buttons to set the time.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Using the Timer Functions  
Se  
o
Caution  
Sleep  
• You cannot change the settings to the current time or turn off time  
during playback timer or recording timer operation.  
• The timer functions can only be used with an z-connected  
Integra/Onkyo cassette tape deck or MD recorder.  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
t
T-D/ST  
Muting  
Surround  
A.Control  
Repeat  
A-B  
Please make sure that the system is properly connected.  
The playback timer and recording timer will not function  
if connections are incomplete  
Late Night  
Audio  
Timer  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507M  
Using the Sleep Timer  
Types of timers  
SLEEP:  
Puts the system into standby mode at the  
preset time.  
The sleep timer is activated by the Sleep  
button.  
Press Sleep.  
“SLEEP 90min” appears in the multipurpose  
display for about 5 seconds, which means the  
unit will turn off and enter standby mode in 90  
minutes. Also the SLEEP indicator is lit in the  
display while the sleep timer is On.  
l
(Playback)  
ONCE:  
Activates only once after setting.  
WEEKDAY: Activates playback timer during weekdays  
(mon-fri).  
• You can change particular days of the week.  
WEEKEND: Activates playback timer during weekends.  
• You can change particular days of the  
weekend.  
Each press of the Sleep button makes the  
remaining time shorter by 10 minutes. Press  
the Cursor 5/∞ buttons to adjust the time in 1  
minute intervals.  
• You can set WEEKDAY and WEEKEND times  
to the same day.  
(Recording)  
REC:  
Can be set to ONCE, or EVERY. Setting to  
ONCE, activates the record timer only once.  
Set to EVERY to record at a particular time  
everyday.  
Checking the remaining time  
Press Sleep while the Sleep Timer is On.  
If you press Sleep while the remaining time is displayed, the  
remaining time is reduced by 10 minutes.  
I About the timer display  
When pressing Timer repeatedly to display the various times,  
a lit TIMER indicator means that the time is set.  
Canceling the Sleep Timer  
Press Sleep repeatedly until the SLEEP indicator goes  
off.  
Lights  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Standby  
Se  
l
o
l
For FM, AM timer playback, first preset the radio stations  
(page 35).  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
Caution  
t
2/3/5/∞  
ENTER  
T-D/ST  
Muting  
Surround  
A.Control  
If the current time is not set, you cannot preset the playback timer.  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507M  
Presetting the playback timer  
Timer  
Repeatedly press Timer to select  
Press (5/∞) to select the stop  
4
5
1
the desired timer type.  
playback time.  
ENTER  
When the desired time is displayed, press  
ENTER.  
«
Press ENTER to select either “WEEKDAY”  
“WEEKEND”, “ONCE.”  
«
When radio timer playback is selected, use  
the cursor buttons to display the desired  
station, then press ENTER.  
ENTER  
Hint  
ENTER  
The TIMER indicator at the top of the display  
lights up when the respective timer is set.  
Skip to step 6 if you selected ONCE timer.  
Repeatedly press (5/∞) to select  
2
Setting the day.  
The characters displayed represent the  
current day setting.  
the component type of timer  
playback.  
ENTER  
Press ENTER when the desired  
component is displayed.  
«
Sun. Tue. Thu.  
Mon. Wed.  
Sat.  
Set  
Fri.  
• If you select a component, which is not  
connected to this unit, the timer will  
To change the day.  
ENTER  
Press (2/3) so that the desired day blinks.  
Press (5/∞) to select/deselect the day.  
activate, and the unit will turn on, and  
the function will change at the timer  
time, but nothing will happen.  
ENTER  
Press (5/∞) to select the start  
playback time.  
3
When the desired time is displayed, press  
ENTER  
ENTER.  
Press ENTER to confirm the  
setting.  
6
7
«
ENTER  
Lights  
Tip  
• When set to the desired playback start time  
(ON) is set, playback is automatically set to  
ENTER  
stop (OFF) in an hour.  
• When using the 24 hour display, if you first  
press Mode DVD, you can also use the  
number buttons.  
The Timer indicator lights up.  
Set the power to Standby  
Press Standby to put the system into  
standby mode.  
Caution  
Even if the playback timer is set, the timer will  
not operate unless the power is set to the  
standby mode. Make sure the system is in  
standby mode.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Using the Timer Functions  
Se  
l
o
l
Be sure to preset FM and AM stations beforehand  
(page 35).  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
Caution  
t
T-D/ST  
Muting  
2/3/5/∞  
ENTER  
Surround  
A.Control  
• If the current time is not set, you cannot preset the playback timer  
make sure that the current time is set.  
Repeat  
A-B  
• Except for EVERY, all record timers record only once. When the  
recording is finished, the timer is deactivated.  
• The record timer can only be used with an z-connected  
Integra/Onkyo cassette tape deck or MD recorder.  
Late Night  
Audio  
Timer  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
--
0
Search  
Enter  
/
RC-507M  
Setting the record timer  
Timer  
Press (5/∞) to select the desired  
Repeatedly press Timer on the  
1
5
6
radio station.  
remote control to select REC.  
ENTER  
Display the desired radio station, then  
press ENTER.  
Press ENTER after selecting “REC”.  
«
«
ENTER  
ENTER  
Press (5/∞) to select the recording  
source.  
Select TV, FM or AM then press ENTER.  
2
Press the (5/∞) cursor buttons to  
select ONCE or EVERY, then press  
ENTER.  
ENTER  
ENTER  
If you select ONCE, proceed to step 7-1. If  
you select EVERY, proceed to step 7-2.  
«
«
Caution  
Setting the recording timer to ONCE will only  
ENTER  
record one time.  
ENTER  
Repeatedly press (5/∞) to select  
3
the recording start time.  
ONCE recording:  
Press (5/∞) to select a day (or NEXT).  
7-1  
ENTER  
When the desired time is displayed, press  
ENTER.  
(Displays when your next set time)  
ENTER  
«
Tip  
OR  
• When setting the timer for MD recording, set  
«
ENTER  
(Selects the day of week)  
the recording to start one minute in ahead  
since there are cases when recording will not  
start for a few seconds.  
The selected day blinks.  
ENTER  
• When set to the desired playback start time  
(ON) is set, playback is automatically set to  
stop (OFF) in an hour.  
• When using the 24 hour display, if you first  
press Mode DVD, you can use the number  
buttons to set the time.  
The current day lights up.  
Press ENTER. The timer indicator lights  
up.  
Press (5/∞) to set the recording  
4
end time.  
ENTER  
Display the desired time, then press  
ENTER.  
«
ENTER  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Standby  
Se  
l
o
T
l
Step/Slow  
CH  
Tun  
ENTER  
VOL  
5/∞  
t
T-D/ST  
Muting  
Surround  
A.Control  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507  
M
Switching the timer on or off  
EVERY recording:  
Set the day.  
• Use when you want to cancel an active timer setting, reset  
a canceled timer, or when you want to revise a record  
timer.  
7-2  
• If the current time is not set, you cannot preset the timer.  
ENTER  
To change the day of week setting:  
Repeatedly press Timer to select  
Timer  
1
Press (2/3) so that the desired day blinks.  
«
the desired timer type.  
The Timer indicator at the top of the display  
lights up when the respective timer is set.  
ENTER  
Press (5/∞) to select/deselect the day.  
Use (5/∞) to switch the timer on or  
2
off.  
Press ENTER to confirm the setting.  
The timer indicator lights up.  
Approx. 2 seconds after switching the  
timer, the previous screen will reappear.  
ENTER  
Set the power to Standby.  
Press Standby to put the system into  
standby mode.  
8
• The muting function activates during  
timer recording. If you would like to  
monitor the sound during recording,  
press Muting on the remote to cancel  
the muting function.  
or  
Caution  
Caution  
• Even if the record timer is set to sure the  
timer, the timer will not operate unless the  
power is set to the standby mode. Make sure  
the system is in standby mode.  
Pressing ENTER, activates the start time (etc.)  
setting mode.  
I In the case of overlapping timer settings  
• If WEEKDAY timer end time and the REC timer start time  
are set to the same time, the REC timer will not activate.  
Please all a one-minute difference end time and start time  
of each times.  
Active  
WEEKDAY  
Canceled  
REC  
• If two or more ONCE / WEEKDAY / WEEKEND / REC are  
set to the same timers start times are given the following  
priority: ONCE → WEEKDAY → WEEKEND → REC.  
• If the REC timer is deactivated because the power is  
already on (etc.), the TIMER indicator does not light in the  
display and the timer settings are cancelled.  
Active  
WEEKEND  
Time  
9:00  
»
10:00  
»
11:00  
»
12:00  
»
• If the power is already on when a timer’s start time occurs  
and there is another overlapping timer, the second timer  
will not operate. The power turns off automatically at the  
end time of the first timer.  
on  
off  
on  
off  
• When the power is turned on during timer playback, even if  
you set another timer, it will not be activated. The initial  
timer is canceled when the standby mode is initiated.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying the Sound Effects  
The surround sound of the DVD Receiver enables you to enjoy the presence of a movie theater or concert hall in your room.  
Before using any sound effect, make sure the Speaker Setup configurations have been set (see pages 26-28).  
The speaker configuration is very important for surround sound. See “Connecting Speakers” on page 17 and “Positioning  
Speakers” on page 18.  
Following are the sound systems the DVD Receiver can reproduce.  
DOLBY DIGITAL Surround and DTS (Digital  
Theater System) Surround  
DOLBY PRO LOGIC II Surround  
This is a 5-channel surround system of a new generation,  
bridging the gap between the previous 4-channel (Left/Right  
Front, Center and monaural surround channels) Pro Logic  
surround and 5.1-channel Dolby Digital surround. Dolby Pro  
Logic II provides a Movie mode optimized for viewing movies  
and a Music mode optimized for listening to music. In the  
Movie mode, the surround channel, which was monaural and  
based on narrow band, is reproduced in stereo so that the  
feeling of movement in the played movies is enhanced. In  
the Music mode, the surround channel reproduces natural  
sound field even with 2-channel music sources.  
Recommended speaker setup  
Center Speaker  
Left front speaker  
Right front speaker  
Subwoofer  
Left surround speaker  
Right surround speaker  
The Movie mode allows you to enjoy VHS and DVD software  
This 5.1 channel digital surround format enables you to  
individually play five full-range (20Hz–20kHz) channels (left  
and right front, center, and two surround channels) plus an  
LFE (Low Frequency Effect) channel for low-range effect  
sound. It will create a realistic sound like that heard in  
theaters and concert halls.  
carrying the  
marking as well as some of TV  
broadcast programs. The Music mode allows you to enjoy  
stereo music from CD, etc.  
Integra’s original Digital Signal Processing  
(DSP) modes  
DOLBY DIGITAL Surround  
DVD videos that have the  
this system.  
The DVD Receiver offers the following special Integra sound  
effects for sources other than Dolby Digital and DTS sounds.  
mark are recorded using  
To playback DOLBY DIGITAL Surround sound from  
connected equipment, you must make the digital connection  
in addition to the above speaker configuration.  
Orchestra  
This mode is suitable for classical and opera music. The  
center channel is cut and the surround channels are  
emphasized to widen the stereo image. It simulates a natural  
reverberation as created in a large hall.  
DTS Surround  
DVD videos and audio CDs that have the  
recorded using this system.  
mark are  
Unplugged  
This mode is suitable for acoustic instrumental sounds,  
vocals, and jazz music. By emphasizing the front stereo  
image, it simulates the acoustics in front of the stage.  
To playback DTS Surround sound from connected equipment  
such as an LD player, you must make the digital connection  
in addition to the above speaker configuration.  
Notes on DTS Surround  
Studio-Mix  
• If you play a DTS Surround encoded disc with the DVD Receiver,  
or a DTS encoded disc using a digitally connected player, you may  
hear a noise for a short while until the DTS decoder of the DVD  
Receiver recognizes the DTS encoded signal and starts operating.  
This is not a malfunction.  
This mode is suitable for rock and popular music. Lively  
sounds with a powerful acoustic image will make you feel as  
if you are in a club.  
• If you play a DTS Surround source in fast reverse or fast forward,  
pause, or skip a chapter or track, noise may be heard. This is not  
a malfunction.  
TV Logic  
This mode offers the realistic acoustics of a TV program  
being aired in the TV studio. It enhances the entire surround  
sound and clarity of conversation.  
• Even when playback of the DTS Surround source stops and the  
DTS signal transmission ends, the DVD Receiver remains in DTS  
mode and the DTS indicator remains lit. This is to prevent noise  
when you pause, fast forward, fast reverse, or skip a chapter or  
track of the playback source. Therefore, if the source switches  
from the DTS signal to a PCM (2 channel digital stereo) signal  
suddenly, the PCM signal may not be played. In such a case, stop  
playback for about three seconds, then resume playback.  
• Some CD players (if connected to the DVD Receiver) and LD  
players may be unable to play DTS Surround sources correctly  
even if you connect the player to the DVD Receiver digitally. In  
such a case, the digital signals (such as the output level, sampling  
frequency, frequency response, etc.) processed by the DVD  
Receiver cannot be recognized as DTS data by the DVD Receiver  
and you may hear noise instead of the proper sound.  
All Ch St (All Channel Stereo)  
This mode is useful for background music. The front and  
surround channels will create a stereo image.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Input Sources and Available  
Listening Modes  
Theater-Dimensional (T-D)* mode  
The ideal home theater is realized by the multichannel sound  
reproduction with the complete speaker configuration and  
speaker positioning described on page 18. However,  
sometimes it is difficult to meet all those conditions. In reality,  
you may only have front speakers, or not be able to place the  
surround speakers in position.  
The available listening modes varies depending on the  
sound type of the input source. The table below shows the  
correlation between the input source types and listening  
modes.  
(The sources listed at the top of each column can use the  
listening modes marked with an ×.)  
Even if your speaker system is not complete, you can enjoy  
the multichannel surround sound by using the Theater-  
Dimensional mode. Theater-Dimensional mode sets the  
output channels to generate the most suitable virtual  
surround reproduction according to the number of the  
speaker channels set in “Speaker Setup” on page 26.  
Input Source Signals  
Analog/PCM Dolby Digital  
DTS  
Possible Cassette tape  
sources  
deck, Video  
tape, Audio CD,  
VIDEO CD,  
DVD video,  
DVD video,  
LD,  
Audio CD,  
Video tape,  
Record,  
FM broadcast,  
AM broadcast  
Digital  
(satellite)  
broadcast  
Listening  
Modes  
The importance of the speaker setup  
LD  
Calibrating each speaker’s sound pressure is essential for  
home theater sound reproduction. The same thing can be  
said for virtual surround sound reproduction. Especially level  
matching and the time alignment of the two speakers that  
reproduce virtual surround signals becomes an even more  
important factor than with normal multichannel reproduction.  
PCM 96kHz  
other  
×
2/0  
×
other  
×
STEREO  
×
×
×
THEATER-DIMENSIONAL  
DOLBY DIGITAL  
DTS  
×
×
×
×
×
For the DVD Receiver, the calibration for the multichannel  
reproduction (see “Setting the Distance from the Listening  
Position to Each Speaker” on page 27 and “Adjusting Each  
Speaker’s Relative Volume Balance - Test Tone” on page 28)  
provides the most appropriate level matching.  
PL II MOVIE/PL II MUSIC  
ORCHESTRA  
UNPLUGGED  
STUDIO-MIX  
×
×
×
×
×
×
×
TV LOGIC  
ALL CH ST  
Notes  
• For input sources which include surround channel signals like the  
multichannel DOLBY DIGITAL and DTS surround sounds, virtual  
processing is applied to those surround channel signals.  
• For 2 channel input sources, the surround channel elements are  
automatically extracted with DOLBY PRO LOGIC processing  
before virtual processing is applied.  
• For monaural or front 3 channel stereo sources, the virtual  
surround effect does not work since those input sources do not  
include the surround channel signals.  
* Theater-Dimensional is a virtual surround technology developed  
by Onkyo. This technology is approved by Dolby Laboratories for  
the virtual surround processing of Virtual Dolby Digital and Virtual  
Dolby Surround products.  
Note  
• The listening mode is set to “STEREO” when a PCM sound with a  
sampling frequency higher than 48kHz is played. Such high-  
resolution sounds are reproduced from sources such as DVD  
video.  
• When the Speaker setup is set to 2 channels (SP 2CH), you can’t  
select DOLBY DIGITAL, DTS or PLII MOVIE/PL II MUSIC. Also,  
when speaker setup is set to 2 channels (SP 2CH) or 3 channels  
(SP 3CH), you can’t select ORCHESTRA, UNPLUGGED,  
STUDIO-MIX, TV LOGIC or ALL CH ST.  
Checking the Sound System of the  
Playing Source  
The DVD Receiver will automatically detect the sound  
system when DOLBY DIGITAL Surround (  
), DTS  
Surround ( ), or PCM/MP3 DIGITAL (2 channel digital  
stereo) is played back. The corresponding sound system  
indicator lights in the DVD Receiver’s display.  
DOLBY DIGITAL DTS  
DIGITAL (PCM/MP3)  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying the Sound Effects  
Choosing Theater-Dimensional Mode  
Theater-Dimensional mode is the technology which controls  
the characteristics of the sounds reaching the listener’s left  
and right ears, therefore, there is a sweet spot where you  
can best experience the Theater-Dimensional effects. You  
need to adjust the location of the sweet spot and these other  
factors for the best possible Theater-Dimensional effect.  
en  
Se  
o
Before operating the  
remote controller  
Press Mode Recvr.  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
T-D/ST  
Muting  
Surround  
A.Control  
Listening angle  
T-D/ST  
(“LSTN. ANGLE” appears in the display.)  
Theater-Dimensional indicator  
Repeat  
A-B  
Left speaker  
Right speaker  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
R
L
R
L
Last  
M
Program Random  
Clear  
The greater the distance  
between the two speakers is,  
the wider the angle is.  
Listening  
angle  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
Up/Down 5/∞  
6
Up/Down  
9
IPM  
7
T-D Setup  
8
40°  
T-D Setup  
+10  
-- --  
0
Search  
Enter  
/
20°  
RC-507M  
Stereo/Theater-Dimensional  
See “The Input Sources and Available Listening Modes” on  
page 47.  
Press T-D/ST on the remote  
1
controller or Stereo/Theater-  
The listening angle is the angle at the listening position  
where the two lines from the left and right speakers meet.  
Remote controller  
Dimensional on the unit.  
-
T D/ST  
“Theater-Dimensional” scrolls across in  
the display and the Theater-Dimensional  
indicator on the unit lights. In other  
You need to adjust the listening angle in the following  
cases:  
• Consider the listening angle as being formed from the  
left and right front speakers since the virtual surround  
signals are output from the front speakers.  
listening modes, press once to change to  
Stereo and press again to change to T-D.  
Unit  
Set “LSTN. ANGLE” to one of the following settings, which  
you feel is most effective (the listening angles in  
parentheses are ideal):  
To change the listening angle, proceed to  
the following steps.  
• Normal (30°)  
• Wide (40°)  
• Narrow (20°)  
Press T-D Setup.  
2
Notes  
“LSTN. ANGLE” is displayed, then the  
current Listening Angle setting is  
displayed.  
Remote controller  
only  
• Theater-Dimensional mode cannot be activated if;  
– Headphones are connected, or  
– The source is PCM sound with a sampling frequency higher than  
48kHz.  
-
T D Setup  
8
• Theater-Dimensional mode will be canceled and the T-D indicator  
goes off when:  
– Another listening mode is chosen, or  
– The input source is switched to a type of source which Theater-  
Dimensional mode cannot process.  
Press Up/Down 5/∞ to select the  
setting of the item.  
Each press of the button changes the item  
as follows:  
3
Remote controller  
only  
6
Up/Down  
9
NORMAL  
↓
WIDE  
↓
NARROW  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Dolby Pro Logic II/  
Changing the Sound to Stereo  
Integra’s Original DSP Modes  
See “The Input Sources and Available Listening Modes” on  
page 47.  
See “The Input Sources and Available Listening Modes” on  
page 47.  
en  
en  
g
Se  
l
Se  
o
o
e
l
Step/Slow  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
VOL  
CH  
Tun  
ENTER  
t
T-D/ST  
Muting  
T D/ST  
-
Muting  
Surround  
A.Control  
A.Control  
Surround  
T-D/ST  
Surround  
Repeat  
A-B  
Repeat  
A B  
-
Late Night  
Audio  
Timer  
Timer  
Late Night  
Audio  
Angle  
Subtitle FM Mode  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
6
Up/Down  
9
IPM  
7
T-D Setup  
8
IPM  
7
T D  
-
Setup  
8
+10  
-- ---  
0
Search  
Enter  
+10  
-- ---  
0
Search  
Enter  
/
/
RC-507  
M
-
RC 507  
M
Stereo/Theater-Dimensional  
Surround Mode  
Remote controller  
Remote controller  
Press Surround on the remote  
Press T-D/ST on the remote  
controller or  
Stereo/Theater-Dimensional on the  
unit.  
Surround  
controller or Surround Mode on the  
unit to choose “PL II” or the DSP  
mode.  
-
T D/ST  
The current listening mode appears in the  
display when the button is pressed once,  
then each press of the button changes the  
listening mode as follows:  
In the display, “STEREO” appears and the  
STEREO indicator lights up.  
Unit  
Unit  
DSP indicator  
PL II MOVIE → PL II MUSIC  
↑
↓
ALL CH ST  
ORCHESTRA  
↑
TV LOGIC  
↑
↓
UNPLUGGED  
↓
STUDIO-MIX  
• In the display, “PL II MOVIE” or “PL II  
MUSIC” appears and the Ÿ PRO LOGIC II  
indicator lights up.  
• PL II and DSP mode cannot be selected  
when “SPEAKER 2CH” is selected. (Only  
“STEREO” can be selected.)  
• Only “PL II MOVIE”, “PL II MUSIC” or  
“STEREO” can be selected when  
“SPEAKER 3CH” is selected.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying the Sound Effects  
Adjusting Each Speaker’s Relative Volume Balance Temporarily  
You can readjust each speaker’s relative volume balance  
according to your preference while listening to the sound.  
The adjusted values will return to the values set on page 28  
when the DVD Receiver enters standby mode, or the main  
power is switched off unless you save the values.  
en  
Before operating the  
remote controller  
Press Mode Recvr.  
Note  
g
You cannot adjust the volume balance while the muting function is  
activated.  
Se  
l
o
e
a
l
Step/Slow  
CH  
Tun  
ENTER  
VOL  
t
T-D/ST  
Muting  
Surround  
A.Control  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
Test Tone  
CH Sel  
Up/Down  
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- --  
0
Search  
Enter  
/
RC-507  
M
CH Sel  
(Checking each speaker’s relative  
(Adjusting each speaker’s relative  
1
2
3
volume balance)  
volume balance)  
Remote controller  
only  
While playing the source, press  
CH Sel repeatedly.  
Each press of the button changes the  
speaker which outputs the sound and the  
selected speaker appears in the display in  
the following order:  
Press CH Sel repeatedly to select  
the speaker, then press Up/Down  
5/∞ to adjust the volume level.  
The volume level can be adjusted  
between –12dB and +12dB.  
CH Sel  
3
6
Up/Down  
9
Repeat this step to change another  
speaker’s volume balance.  
LEFT (Front left ch.)  
↓
CENTER (Center ch.)  
↓
Saving the adjusted values  
RIGHT (Front right ch.)  
↓
Remote controller  
only  
Press Test Tone.  
SURR R (Surround right ch.)  
↓
Test Tone  
SURR L (Surround left ch.)  
2
↓
SUBWFR (Subwoofer)  
↓
Speaker volume adjustment mode off  
Note  
Any speaker that is not included in the speaker  
configuration on page 26 is not selected even if  
it is actually connected.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the LATE NIGHT Function  
Boosting the Super Bass Sounds/High  
Frequency Sounds  
• The LATE NIGHT function operates when the sound is  
DOLBY DIGITAL Surround.  
If you play a movie at low volume at night, set this function  
to “LOW” or “HIGH” to narrow the dynamic range of the  
sound and make it easier to hear.  
You can enjoy more dynamic sounds by boosting the super  
bass/high frequency sounds, even with decreased volume.  
en  
en  
Se  
o
Se  
l
o
l
Step/  
Slow  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
CH  
Tun  
ENTER  
VOL  
t
T-D/ST  
Muting  
T-D/ST  
Muting  
Surround  
A.Control  
Surround  
A.Control  
A. Control  
Repeat  
A-B  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Late Night  
Audio  
Timer  
Late Night  
Angle  
Subtitle FM Mode  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
6
Up/Down  
9
IPM  
7
T-D Setup  
8
IPM  
7
T-D Setup  
8
+10  
0
Search  
Enter  
+10  
-- ---  
0
Search  
Enter  
--  
/
--  
/
Acoustic Control  
RC-507  
M
RC-507M  
Remote controller  
Press A. Control on the Remote  
controller or Acoustic Control on  
the unit.  
A.Control  
Remote controller  
only  
Press Late Night.  
The current setting appears in the display.  
Each press of the button changes the  
acoustic mode as follows:  
Late Night  
To change the setting, press the button  
repeatedly while the current setting is  
displayed.  
→
“A. CTRL 1” appears in the display  
and the A.CTRL indicator turns on.  
Unit  
• When the button is pressed while  
DOLBY DIGITAL Surround sound is  
being reproduced  
“L.N OFF”, “L.N HIGH” or “L.N LOW”  
can be selected.  
The super bass sounds are boosted.  
↓
“A. CTRL 2” appears in the display  
and the A.CTRL indicator turns on.  
The super bass sounds are further  
reinforced and the high frequency  
sounds are also reinforced.  
↓
“A. CTRL OFF” appears in the display  
and the A.CTRL indicator goes off.  
Note  
The LATE NIGHT effect is determined by each DOLBY DIGITAL  
sound source. Some sources may produce little or no effect.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Locating a Specific Title/Folder/  
Chapter/Track/Location  
en  
Se  
l
o
l
Before operating the  
remote controller  
Press Mode DVD.  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
t
T-D/ST  
Muting  
Surround  
A.Control  
£
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
Number  
buttons  
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
Search  
/
RC-507  
M
DVD  
VCD  
CD  
MP3  
Searching for a Title, Folder, Chapter,Track, or Location on a Disc  
Notes  
This DVD Receiver offers different ways of accessing the  
information on a DVD, Video CD, CD or MP3. Using Search,  
you can search for titles or chapters on a DVD, tracks on a  
Video CD, CD or folders or tracks on a MP3 and even select  
the point in time to start playback.  
• For some discs, selection can be made using the top menu on  
the DVD. In this case, press Top Menu to display the menu  
screen and then make your selection.  
• With some DVDs, the search operation may not be possible and  
may stop shortly after being performed. In this case, the  
mark  
will appear on the screen.  
Press Search repeatedly to select  
• Time search is not possible with CDs and MP3s.  
• When performing DVD or Video CD time search, playback may  
start from a slightly different time than that specified.  
• Time search is not possible when the disc is stopped.  
• Searching using time search is not possible during PBC playback  
of Video CDs.  
Search  
1
the type of search.  
Enter  
The type of search changes which each  
press as follows.  
DVD  
3 Title  
Off 2  
3 Chapter  
Time 2  
I To perform a direct title or chapter/track  
search using the number buttons  
• Press the number buttons while the disc is stopped to  
select a title or track number.  
Video CD  
3 Track  
3 Time  
Off 2  
• Press the number buttons while the disc is playing to select  
a chapter or track number.  
• To select number 3, press 3.  
CD  
3 Track  
3 Off  
• To select number 10, press +10 and 0.  
• To select number 37, press +10, +10, +10 and 7.  
MP3  
3 Folder  
3 Track  
Off 2  
Press the number button(s) of the  
desired title, chapter or track or of  
the specific time where you would  
like to begin playback.  
2
SP Setup  
Test Tone  
CH Sel  
3
1
SW Mode  
4
2
Distance  
5
6
Up/Down  
9
-
T
IPM  
7
D Setup  
8
• To select number 3, press 3.  
• To select number 10, press 1 and 0.  
• To select number 87, press 8 and 7.  
0
When performing a time search:  
• To select 21 minutes, 43 seconds,  
press 2, 1, 4, and 3.  
• To select 1 hour, 14 minutes, press 7, 4,  
0, and 0.  
Press £.  
3
Playback of the selected title, folder,  
chapter or track starts. When a time search  
is performed, playback begins at the  
appointed time.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Se  
o
l
Top Menu  
Program  
Menu  
Before operating the  
remote controller  
Press Mode DVD.  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
2/3/5/∞  
ENTER  
£
t
T-D/ST  
Muting  
Surround  
A.Control  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507M  
MP3  
Using the MP3 Navigator  
Use the MP3 Navigator to make searching for the track(s) you  
want to play easier. You can also use it to add or clear tracks  
from the program list.  
I Navigate using the following controls:  
Cursor buttons (2/3) Select folder or tracks from the  
current screen.  
Cursor buttons (5/∞) Select the previous/next folders or  
tracks. To move rapidly up or down a  
Load a CD-ROM containing MP3  
1
tracks.  
long list of folders or tracks, press  
and hold the Cursor buttons (5/∞).  
Press Menu to enter the MP3  
Navigator screen.  
The left side of the screen shows a list of  
folders containing MP3 tracks.  
ENTER  
Play the currently selected folder or  
track. MP3 tracks that are unplayable  
on this system are automatically  
skipped and the display shows  
“UNPLAYABLE”.  
2
Total number of Tracks  
Menu  
Exit the MP3 Navigator  
MP3 Navigator  
Current :  
3
1-3  
Program  
Add the currently selected track to  
the program list. (Tracks in the  
program list are marked .)  
Pressing Program repeatedly will add  
the track to the program list  
repeatedly.  
Folder  
Track  
1.01_LOO~1  
2.02_SWE~1  
3.03_FAL~1  
4.04_CAR~1  
5.05_SOS~1  
1.F_001  
2.F_002  
3.F_003  
ENTER  
SETUP  
Play  
Exit  
Total number of Folders  
See “Programming MP3s” on page  
58 for how to use program play.  
If you display the MP3 Navigator when a  
disc is playing, the currently playing folder  
and track numbers are shown at the top  
left of the screen.  
Clear  
Clear the currently selected track  
from the program list.  
On the right side is a list of MP3 tracks  
from the first folder in the list on the left.  
MP3 Navigator  
1~20  
Current :  
1~1  
3
1-3  
Folder  
Track  
1.F_001  
2.F_002  
3.F_003  
1.01_LOO~1  
2.02_SWE~1  
3.03_FAL~1  
4.04_CAR~1  
5.05_SOS~1  
CLEAR  
ENTER  
SETUP  
Clear  
Play  
Exit  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Se  
o
Repeat Play  
You can repeat an entire title, folder, chapter or track, or  
just a part.  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
t
T-D/ST  
Muting  
Surround  
A.Control  
£
A-B  
Repeat  
A-B  
Repeat  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- --  
0
Search  
Enter  
/
RC-507M  
DVD  
VCD  
CD  
DVD  
VCD  
CD  
MP3  
Repeating a Disc,Title, Folder, Chapter  
or Track  
Repeating a Specific Segment  
Repeat play of a specified section  
-
A B  
Repeat  
Press Repeat repeatedly.  
Each time you press Repeat, the repeat  
mode changes as follows:  
Press A-B at the beginning and  
end of the section you want to  
repeat.  
• First time you press A-B, “Memory  
(REPEAT A)” appears on screen  
(display). When A-B is pressed a  
(Characters in parentheses appear in the  
front panel display.)  
DVD  
second time, the disc returns to the  
location where A-B was pressed first  
and plays the selected section  
repeatedly.  
Repeat Chapter (REPEAT CHP) → Repeat  
Title (REPEAT TTL) → Repeat Off  
(Previous display)  
VCD  
CD  
“RPT” indicator lights up.  
Repeat Track (REPEAT TRK) → Repeat  
Disc (REPEAT DSC) → Repeat Off  
(Previous display)  
MP3  
Return to a specified location on a disc  
Repeat Track (REPEAT TRK) → Repeat  
Folder (REPEAT FLD) → Repeat Disc  
(REPEAT DSC) → Repeat Off (Previous  
display)  
1 Press A-B at the desired  
location.  
2 When you want to return to the  
specified location, press £.  
“RPT” indicator lights up.  
I To cancel A-B repeat play  
Press Clear. Playback continues, but the repeat function is  
canceled.  
I To clear the specified location  
Press Clear to cancel repeat play or to clear the specified  
location that was set using A-B.  
I To repeat a program  
Press Repeat once during program playback to repeat the  
program.  
Notes  
• With some DVDs, there may be times when repeat playback is  
I To cancel repeat play  
Press Clear. Playback continues, but the repeat function is  
canceled.  
not possible. In these cases, the  
mark will appear on the  
screen.  
• With Video CDs, repeat play is not possible when the menu is  
displayed (PBC playback). To perform repeat play, start  
playback without displaying a menu by pressing the track  
number to be repeated when the disc is stopped, and then press  
REPEAT.  
Note  
If you press 4/¢ during track repeat or chapter repeat, the  
repeat mode may be cancelled.  
• You cannot use A-B repeat when listening to an MP3.  
• If you switch camera angle during repeat play, repeat play is  
cancelled.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Still Frame/Slow Play  
The video images on DVD and Video CD can be viewed  
as a still frame, played back at slow speeds and even  
advanced frame by frame.  
g
Se  
l
o
T
e
a
l
Before operating the  
remote controller  
Press Mode DVD.  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
Step/Slow +/–  
t
T-D/ST  
Muting  
Surround  
A.Control  
£
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
DVD  
VCD  
RC-507  
M
DVD  
VCD  
Viewing a still frame  
Viewing slow playback  
Press , Step/Slow +/–.  
Press and hold Step/Slow +/– during  
playback.  
1
When viewing a DVD, if the paused picture  
shakes, select the [Field] setting in the  
Setup screen Video 2 menu [Still Picture]  
setting as described in the section on page  
72.  
Step/Slow  
CH  
Tun  
Step/Slow  
CH  
Tun  
During slow playback, press Step/  
Slow +/– repeatedly to change the  
slow-motion speed.  
2
Step  
/
Slow  
I Frame by frame advance playback:Viewing  
one frame at a time  
You can’t use frame review with Video CDs.  
CH  
Tun  
There are four forward slow-motion play  
speeds (Step/Slow +):  
3 1/16  
3 1/8  
1/2 2  
1/4 2  
1 Press , Step/Slow +/–.  
2 Press Step/Slow +/–.  
There are two reverse slow-motion play  
speeds:  
Step/Slow +:  
The picture advances one frame each  
time the button is pressed.  
Slow 1 ↔ Slow 2  
Step/Slow –:  
The picture backs up a DVD a few frames each  
time the button is pressed.  
Note  
I To return to normal playback  
You can’t use slow reverse play with Video CDs.  
When viewing a still frame playback, pressing or £  
restores normal playback operation.  
I To return to normal playback  
When viewing a slow playback, pressing £ restores normal  
playback operation.  
Notes  
• There is no sound when viewing still frames or slow playback, or  
when advancing one frame at a time.  
• Still frame, slow play, or frame advance playback may not be  
possible with certain titles. In this case, the  
mark is displayed.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playing in a Favorite Order  
The titles and chapters within a title on a DVD and  
similarly MP3, CD and Video CD tracks can be arranged  
to play in the order you want.  
With this DVD receiver, it is possible to make a program  
as you watch a DVD or Video CD or while listening to an  
MP3 or a CD.  
DVD  
Programming DVDs  
A program with a maximum of 24 steps can be memorized.  
In the program window, use the  
number buttons to enter the  
numbers of the titles or chapters in  
the order you want to program them  
in.  
4
Press Program.  
The Program screen appears.  
SP Setup  
Test Tone  
CH Sel  
3
Program  
1
SW Mode  
4
2
Distance  
5
1
6
Up/Down  
9
-
T
IPM  
7
D Setup  
8
Program Chapter  
Current:  
Program Title  
2(/20)  
Title  
• To program DVD titles/chapters 9, 7,  
and 18 in order, press 9, 7, +10 and 8.  
+
10  
-- ---  
0
/
Program Chapter  
Current:  
Program Title  
2(/20)  
Title  
Program Memory Off  
18  
09  
07  
ENTER  
PROGRAM  
Chapter  
Move  
Play  
Exit  
1
Program Chapter  
Program Title  
Program Memory Off  
Move  
7
Title  
1
Current:  
Title  
(Chapter 1~18)  
ENTER  
PROGRAM  
Exit  
Play  
Program Memory Off  
Input title number  
ENTER  
PROGRAM Exit  
Move  
Play  
Program Chapter  
Program Title  
“PROGRAM” appears in the display.  
7
1
Chapter  
Title  
1
Current:  
Title  
(Chapter 1~18)  
09  
07  
18  
Use the cursor buttons (2/3) to  
select either [Program Chapter] or  
[Program Title].  
2
3
ENTER  
Program Memory Off  
ENTER  
PROGRAM  
Exit  
Move  
Play  
Once the program type is selected.  
Use the cursor button (∞) to enter  
the program window.  
Input chapter number  
ENTER  
When [Program Chapter] is selected, you  
must also select what title the chapters to  
be programmed are in. Use the cursor  
button (5) to highlight “Title” and then use  
the number buttons to enter the title  
number to be used.  
Press ENTER or £.  
• Playback starts in the set order.  
5
ENTER  
• Press Program to return to the previous  
display. The program will not begin until  
£ is pressed.  
• To stop the program play, press 7.  
Notes  
• When programming chapters, chapters not programmed may  
appear on the screen. This is not a malfunction.  
• Programming may not be possible with certain DVDs. On these  
types of discs, the  
mark will appear on the screen when  
programming is attempted.  
• Only chapters within the same title can be programmed during  
chapter programming.  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Sel  
o
T
l
Before operating the  
remote controller  
Press Mode DVD.  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
2/3/5/∞  
ENTER  
£
t
T-D/ST  
Muting  
Surround  
A.Control  
Repeat  
A-B  
7
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
Program  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
Number  
buttons  
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507M  
VCD  
CD  
Programming Video CDs, CDs  
A program with a maximum of 24 steps can be memorized.  
I To save a program in memory  
This DVD Receiver can memorize the programs on up to 24 DVDs.  
By turning the [Program Memory] to [On], the DVD Receiver will save  
your program and recall it the next time you use the same DVD.  
When the program memory exceeds 24, programs will be erased in  
chronological order from the oldest program in memory.  
Press Program.  
Program  
1
The program screen appears. When a  
Video CD or CD is loaded, the cursor  
appears in the program window.  
Program Track  
1 Use the cursor button (∞) to highlight [Program Memory]  
and use the cursor button (3) to select [On].  
1(/10)  
0.00  
Track  
Current:  
Total Time  
Program Chapter  
Program Title  
7
1
Title  
1
Chapter  
Current:  
Title  
(Chapter 1~18)  
ENTER  
PROGRAM  
Exit  
Move  
Play  
Program Memory On  
Off  
Move  
ENTER  
PROGRAM  
Exit  
Select  
2 Press ENTER.  
Use the number buttons to enter the  
numbers of the tracks in the order  
you want to program them in.  
• To program tracks 9, 7, and 18 in order,  
press 9, 7, +10 and 8.  
The program is saved in memory.  
2
SP Setup  
Test Tone  
CH Sel  
3
Note  
1
SW Mode  
4
2
Distance  
5
When a DVD with a program stored in memory is loaded, program  
playback may start automatically.  
6
Up/Down  
9
-
T
IPM  
7
D Setup  
8
+
10  
-- ---  
0
I To erase a program saved in memory  
• To edit the program, refer to the  
/
procedures on the previous page.  
The DVD receiver erases programs in chronological order when the  
maximum number of programs that can be held in memory is  
exceeded. To prevent the DVD receiver from erasing older programs  
that you may still use regularly, or when you don’t want to use a  
program anymore, it is possible to manually erase programs stored  
in memory.  
Press ENTER or £.  
• Playback starts in the specified track  
3
ENTER  
order.  
1 Load a DVD that has a program stored in memory.  
2 Press Program.  
• Press PROGRAM to return to the  
previous display. The program play will  
not begin until £ is pressed.  
The program screen appears.  
3 Use the cursor button (∞) to highlight [Program Memory]  
and use the cursor buttons (3/∞) to select [Off].  
4 Press ENTER.  
• To stop the program play, press 7.  
The program is cleared from memory.  
If you press Clear in stop mode, the program will be cleared from  
memory and [Program Memory] will be turned to [Off].  
Note  
You cannot program when playing a Video CD using menu  
selections (during PBC).  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Playing in a Favorite Order  
Se  
o
Step/Slow  
Before operating the  
remote controller  
Press Mode DVD.  
CH  
Tun  
ENTER  
VOL  
2/3/5/∞  
T-D/ST  
Muting  
Surround  
A.Control  
ENTER  
£
Repeat  
A-B  
7
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
Program  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
Number  
buttons  
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507M  
MP3  
Programming MP3s  
A program with a maximum of 24 steps can be memorized.  
Use the number buttons to enter a  
three-digit track number.  
The number of tracks in the current folder  
is displayed in the top-left of the screen.  
3
SP Setup  
Test Tone  
CH Sel  
3
Press Program to enter the [MP3  
Program  
1
1
SW Mode  
4
2
Distance  
5
Program] screen.  
6
Up/Down  
9
-
T
IPM  
7
D Setup  
8
If you added tracks to the program list from  
the “Using the MP3 navigator” on page 53,  
the tracks are displayed here.  
Once you’ve entered a valid track number,  
the name of the track appears.  
+
10  
-- ---  
0
/
MP3 Program  
Folder 001~25 – – – – – – – – : – – – – – – – –  
Total number of folder and track  
001:008  
– – –:– – – – – –:– – – – – –:– – –  
Folder name  
Track name  
– – –:– – – – – –:– – – – – –:– – – – – –:– – –  
– – –:– – – – – –:– – – – – –:– – – – – –:– – –  
MP3 Program  
Folder : 001~25  
– – –:– – – – – –:– – – – – –:– – – – – –:– – –  
– – –:– – – – – –:– – – – – –:– – – – – –:– – –  
– – –:– – – – – –:– – – – – –:– – – – – –:– – –  
– – –:– – – – – –:– – – – – –:– – – – – –:– – –  
– – –:– – – – – –:– – – – – –:– – – – – –:– – –  
– – – – – – – – : – – – – – – – –  
ENTER  
PROGRAM  
Exit  
Move  
Play  
– – –:– – – – – –:– – – – – –:– – – – – –:– – –  
– – –:– – – – – –:– – – – – –:– – – – – –:– – –  
ENTER  
PROGRAM  
Exit  
Move  
Play  
«
From this screen you can enter folder and  
track numbers directly to build up a  
program list.  
Press ENTER or £.  
• Playback starts in the set order.  
4
Use the number buttons to enter a  
three-digit folder number.  
The number of folders on the disc is  
displayed in the top-left of the screen.  
ENTER  
• Press Program to return to the previous  
display. The program will not begin until  
£ is pressed.  
2
SP Setup  
Test Tone  
CH Sel  
3
1
SW Mode  
4
2
Distance  
5
6
Up/Down  
9
• To stop the program play, press 7.  
-
T
IPM  
7
D Setup  
8
Once you’ve entered a valid folder number,  
the name of the folder appears.  
+
10  
-- ---  
0
/
MP3 Program  
Track 001~10  
FOLDER~1 : – – – – – – – –  
001:– – –  
– – –:– – – – – –:– – – – – –:– – –  
– – –:– – – – – –:– – – – – –:– – – – – –:– – –  
– – –:– – – – – –:– – – – – –:– – – – – –:– – –  
– – –:– – – – – –:– – – – – –:– – – – – –:– – –  
– – –:– – – – – –:– – – – – –:– – – – – –:– – –  
ENTER  
PROGRAM  
Exit  
Move  
Play  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Se  
o
Before operating the  
remote controller  
Press Mode DVD.  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
2/3/5/∞  
ENTER  
T-D/ST  
Muting  
Surround  
A.Control  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
Program  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
Number  
buttons  
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507M  
DVD  
VCD  
CD  
MP3  
Additional programming options  
After you have made a program, it is then possible to confirm,  
add, or clear the contents of the program.  
I To delete a number  
1 Press Program.  
2 Use the cursor buttons (5/∞/2/3) to highlight the incorrect  
I To confirm the contents of a program  
On a CD or Video CD track program, press Program to  
confirm.  
The program screen displays the current program.  
On a DVD, select the program type (title or chapter) with the  
cursor buttons (2/3).  
number and then press Clear.  
The number is deleted. If the number was before another number,  
the later numbers are reordered automatically.  
3 Press Program to exit the program screen.  
Notes  
• The complete program will be deleted if the disc tray is open or  
power off (standby).  
• Pressing Clear when the disc is stopped will clear all programs.  
The current DVD title or chapter program can then be confirmed on  
the appropriate program screen.  
I To add to a program  
1 Press Program.  
2 Use a number button to add a new title, chapter, or track at  
the end of the program.  
3 Press Program to exit the program screen.  
I To add a title/chapter/track to a program  
during playback  
Press and hold Program for about 2 seconds.  
The current title/chapter/track number appears on-screen together  
with the program step number. If there isn’t already a program then a  
new one will be created.  
e.g. DVD  
Chapter 07 3 Program 03  
I To insert a number  
1 Press Program.  
2 Use the cursor buttons (5/∞/2/3) to highlight the number  
after the new number to be placed and then press the  
number button(s) of the number to be inserted.  
The new number is inserted before the previously selected  
number.  
3 Press Program to exit the program screen.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Random Play  
Se  
o
Play titles, chapters, or tracks on a disc in random order.  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
T-D/ST  
Muting  
ENTER  
Surround  
A.Control  
£
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
Random  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507M  
DVD  
VCD  
CD  
MP3  
Playing in Random Order  
DVD  
VCD  
CD  
MP3  
Random  
Random  
Random playback of chapters within one  
Random playback of tracks  
title  
Press Random.  
Press Random once, then press  
ENTER or £.  
“Random Chapter” appears on the screen,  
and chapters within the title will be played  
back in random order.  
“Random” appears on the screen, “RDM”  
appears in the display, and playback  
begins.  
«
I To change tracks during random play  
• Press ¢ or Random and the next randomly selected track  
starts playing.  
• Press 4 and playback of the current track starts again  
from the beginning.  
ENTER  
Random playback of titles  
Press Random twice, then press  
ENTER or £.  
“Random Title” appears on the screen, and  
titles will be played back in random order.  
I To stop random play  
“RDM” appears in the display.  
Press Clear. This returns you to normal playback of chapters/  
tracks in order from the chapter/track currently playing.  
Notes  
I To change titles or chapters during random  
• With Video CDs, random play is not possible during playback  
when the menu is displayed (PBC playback). To perform random  
play, start playback without displaying a menu by pressing a track  
number button while in the stop mode, and then press Random.  
• Random play of programmed tracks or chapters is not possible.  
• Repeat playback of random playback is not possible.  
• You cannot use random play while using MP3 navigator.  
• Random playback may not be possible with some DVDs.  
play  
• Press ¢ or Random and the next randomly selected title  
or chapter starts playing.  
• Press 4 and playback of the current title or chapter starts  
again from the beginning.  
I To stop random play  
Press Clear. This returns you to normal playback of chapters  
in order from the chapter currently playing.  
Notes  
• Random play of programmed chapters is not possible.  
• Random playback may not be possible with some DVDs.  
• Repeat playback of random playback is not possible.  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting the Audio/  
Subtitle Language  
en  
Se  
l
o
T
l
Menu  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
t
T-D/ST  
Muting  
Surround  
A.Control  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Subtitle  
Clear  
Audio  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
--
0
Search  
Enter  
/
RC-507M  
DVD  
DVD  
Changing the Audio Language (Multi-  
Language Function)  
Selecting a Subtitle Language  
(Multi-Language Subtitles)  
Dolby Digital, PCM, and other audio data can be recorded on  
DVDs in a number of languages or audio tracks, letting you  
choose the desired language or audio.  
You can select a desired subtitle language with DVDs that  
have subtitle data in multiple languages recorded on them.  
Press Subtitle repeatedly during  
Subtitle  
Press Audio repeatedly to select the  
playback.  
Audio  
desired language.  
Pressing Subtitle once displays the  
currently selected subtitle language.  
Subsequent presses rotates through the  
subtitle languages available on the DVD.  
Pressing Audio once displays the currently  
selected language. Subsequent presses  
rotates through the audio languages  
available on the DVD.  
Subtitle :1 English  
Subtitle :2 Spanish  
Dolby Digital  
5.1CH  
Dolby Digital  
5.1CH  
: 2 Spanish  
Audio  
: 1 English  
Audio  
HELLO!  
HOLA!  
Notes  
Notes  
• The subtitle language cannot be switched if the subtitle language  
is not recorded, or if only one language is recorded.  
• Switching the subtitle language may not be possible with some  
discs. In this case, the  
• To clear subtitles during playback, press Subtitle and then press  
Clear, or press Subtitle until [Off] appears.  
• For some discs, subtitle language selection can be made using  
the menu on the DVD. In this case, press Menu to display the  
DVD menu screen and then make your selection.  
• When you erase the resume position or replace a disc, the DVD  
Receiver returns to the automatic setting in the setting menu  
(page 74).  
• You cannot switch languages if there is only one language  
recorded on the disc.  
• Switching the audio language may not be possible with some  
titles. In this case, the  
• For some titles, selection can be made using the DVD menu.  
In these cases, press Menu to display the DVD menu screen and  
then make your selection.  
• When you erase the resume position or replace a disc, the DVD  
receiver returns to the automatic setting in the setting menu  
(page 73).  
mark will be displayed.  
mark will be displayed.  
VCD  
MP3  
I Changing Audio Type  
For enjoyment of karaoke or similar format Video CDs and MP3s it is  
possible to select stereo audio, or either right or left channel mono  
depending on the requirements of the source.  
Press Audio repeatedly during playback to switch the audio  
type.  
Audio output changes from [1/L] (Left channel) to  
[2/R] (Right channel) to [Stereo].  
Audio  
: 2/R  
Audio  
: 1/L  
Audio  
: Stereo  
Note  
With karaoke and other discs, set the appropriate audio type for  
singing and accompaniment after referring to information on the disc  
jacket or accompanying material.  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Continuing Playback from a  
en  
Standby  
Specified Location (Last Memory)  
Se  
l
o
l
The Last Memory function is convenient when you want  
to continue viewing a disc from the point where you were  
watching before. Unlike the resume function, the Last  
Memory function is effective even if the DVD is removed  
from the DVD receiver (Last Memory locations saved for  
Video CDs are effective only if the disc remains loaded in  
the DVD receiver).  
Step/Slow  
CH  
Tun  
ENTER  
VOL  
t
T-D/ST  
Muting  
Surround  
A.Control  
£
Repeat  
A-B  
7
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
Clear  
Last M  
SP Setup  
Test Tone  
CH Sel  
Last Memory may not work reliably with some Video CDs  
that feature PBC.  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507M  
DVD  
DVD  
VCD  
VCD  
Resuming playback from where LAST  
M was pressed  
Memorizing a Last Memory location to  
return to later  
Load a disc that has a Last Memory  
Press Last M during play.  
The “LAST” indicator lights on the DVD  
receiver.  
Last M  
1
1
point memorized.  
Some DVDs will start playback  
automatically when loaded. In this case,  
press 7 to stop playback.  
Press Last M while in the stop  
Last M  
2
a
Press Standby to turn the power to  
mode.  
2
standby, or stop playback with 7.  
The disc begins playback at the  
memorized point.  
Once memorized, the memorized point will  
be recalled even if the power is turned off,  
or if the disc is ejected. Points on up to 5  
discs can be memorized, and those points  
are recalled the next time any of the discs  
are played back.  
• Last Memory mode may not function for  
some DVDs.  
• You can use Last Memory for up to five  
discs (after that the one used least  
recently is deleted to make space for a  
new one).  
• A Last Memory point can be memorized  
for only one Video CD at a time as the  
function is only effective until the Video  
CD is removed from the player.  
• Even with a disc you have memorized  
with Last Memory, playback begins at  
the start of the disc if you press £.  
• This function is for playback of DVDs or  
Video CDs only. You cannot use it with  
CDs and MP3s.  
I To clear the Last Memory location  
1 Load a disc that has a Last Memory point memorized.  
Some DVDs will start playback automatically when loaded. In this  
case, press 7 to stop playback.  
2 Press Last M while in the stop mode.  
The disc begins playback at the memorized point.  
3 Once the picture appears, press Last M again.  
4 While “Last Memory” is displayed on the screen, press  
Clear.  
The “LAST” indicator disappears from the display.  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Selecting the Camera Angle  
Se  
l
o
T
l
Step/Slow  
CH  
Tun  
ENTER  
VOL  
t
T-D/ST  
Muting  
Surround  
A.Control  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Angle  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507M  
DVD  
Viewing from a Desired Camera Angle (Multi-Angle)  
You can select a camera angle when viewing DVDs with  
the multi-angle option.  
I To check whether or not a disc is recorded  
with angles  
The jackets of discs that are recorded with angles will be marked  
Press Angle during playback.  
The camera angle changes each time you  
press the button.  
with  
. When locations on discs that are recorded with angles are  
indicator can be displayed.  
Angle  
played back, the  
To cancel the angle mark, set [Angle Indicator] to [Off] in the Setup  
screen Video menu described in the section below (page 72).  
Angle  
: 1/4  
Angle  
: 2/4  
\
»
«
Angle  
: 4/4  
Angle  
: 3/4  
|
Notes  
• You can use the Multi-Angle function only with discs featuring  
recordings of images shot from different camera angles.  
• For some discs, selection can be made using the DVD menu. In  
this case, press Menu to display the DVD menu screen and then  
make your selection.  
• If you change the camera angle during still playback, the DVD  
Receiver resumes normal playback.  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Viewing Disc Information  
Use Display to get current information about the disc  
currently loaded.You can get information about the titles  
and chapters on a DVD or tracks on a Video CD or CD or  
folders and tracks on a MP3. When viewing DVDs, you  
can also check the digital bitstream transmission rate.  
Se  
l
o
T
Display  
l
Step/Slow  
CH  
Tun  
ENTER  
VOL  
t
T-D/ST  
Muting  
2/3  
Surround  
A.Control  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507M  
DVD  
VCD  
CD  
MP3  
Viewing Disc Information during while a disc is playing  
Video CD (with PBC disabled)  
Press Display during while a disc is  
playing. Press Display repeatedly to  
change the information being  
displayed.  
current track number/  
total number of tracks  
Video CD’s total  
elapsed time  
a
Play  
All  
3/12  
–59.26/  
10.53  
70.19  
The disc information is displayed  
superimposed over the video image on the  
screen.  
Video CD’s  
remaining time  
Video CD’s  
remaining time  
Video CD’s total  
time  
«
«
Press and hold Display to display  
the time remaining on the disc.  
When you release the button, the  
information disappears.  
current track  
number  
Video CD’s total  
elapsed time  
current track  
number  
Play  
Track  
3
10.53  
5.23  
3.56/  
elapsed time of  
current track  
total time of  
current tracks  
elapsed time of  
current track  
The display changes for each type of disc as follows each time  
the button is pressed.  
current track  
number  
Video CD’s total  
elapsed time  
current track  
number  
DVD  
current title/  
chapter number  
elapsed time of  
current title  
current title  
number  
Play  
Track  
3
10.53  
5.23  
1.27/  
Play  
Title  
3–29  
–51.06/ 101.04  
49.58  
remaining time of  
current track  
total time of  
current tracks  
remaining time of  
current track  
remaining time of  
current title  
«
remaining time of  
current title  
remaining total  
time of current title  
Display off  
«
current title/  
elapsed time of  
current title  
current title/  
chapter number  
CD  
chapter number  
elapsed time of  
current track  
current track  
number  
Play  
Chapter  
3–32  
0.21/  
54.53  
1.51  
current track  
number  
Play  
Track  
3
0.03  
3.32  
elapsed time of  
current chapter  
elapsed time of  
current chapter  
elapsed total time  
of current chapter  
–3.29/  
remaining time of  
current track  
remaining total time  
of current tracks  
remaining time of  
current track  
«
current title/  
chapter number  
current title/  
chapter number  
elapsed time of  
current title  
«
total time of  
current track  
current track  
number  
Play  
Chapter  
3–32  
–1.30/  
54.53  
1.51  
Play  
All  
1/10  
–66.20/  
1.13  
66.32  
remaining time of  
current chapter  
remaining total time  
of current chapter  
remaining time of  
current chapter  
CD’s remaining  
time  
CD’s total time  
CD’s remaining  
time  
«
current title/  
chapter number  
elapsed time of  
current title  
«
Play  
Tr. Rate:  
3–32  
54.53  
6.3  
Display off  
transmission rate  
level  
transmission rate  
level meter  
transmission rate  
level  
«
Display off  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Sel  
o
T
Display  
l
Step/Slow  
CH  
Tun  
ENTER  
VOL  
t
T-D/ST  
Muting  
2/3  
Surround  
A.Control  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507M  
DVD  
VCD  
CD  
MP3  
DVD  
VCD  
CD  
MP3  
Viewing Disc Information during while  
a disc is playing  
Viewing Disc Information while a disc  
is stopped  
MP3  
Press Display while a disc is  
stopped to display DVD title and  
a
current track number/  
total number of tracks  
in folder  
elapsed time of  
current track  
chapter information or Video CD  
and CD track information or MP3  
folder and track information. Press  
Display again to turn the display off.  
Information about the titles and chapters or  
folders and tracks on a disc is displayed.  
When the information exceeds the space  
on the screen, use the cursor buttons  
(2/3) to move to other screens.  
Play  
Track  
16/20  
TRACK1~1  
0.05  
track name  
track name  
current folder  
number/total  
number of folders  
«
elapsed time of  
current track  
Play  
Folder  
2/10  
FOLDER~1  
0.05  
folder name  
folder name  
DVD  
Information: DVD  
«
Title  
01  
Chapter  
Title  
06  
Chapter  
1 ~ 10  
1 ~ 13  
1 ~ 5  
1 ~ 30  
1 ~ 21  
1 ~ 46  
1 ~ 12  
1 ~ 8  
current folder number/  
current track number  
elapsed time of  
current track  
02  
07  
03  
08  
current track number  
1 ~ 4  
04  
09  
1 ~ 8  
05  
10  
Play  
Track  
2–16  
–2.25  
0.05  
2.30  
DISPLAY  
Exit  
1/2  
Titles and number of chapters in each title  
remaining time of  
current track  
remaining time of  
current track  
total time of  
current track  
Video CD and CD  
«
Information: Compact Disc  
Total time  
current folder number/  
current track number  
elapsed time of  
current track  
72 . 04  
Track  
06  
07  
08  
09  
10  
current folder number/  
current track number  
Track  
Time  
Time  
01  
02  
03  
04  
05  
5 . 23  
4 . 55  
6 . 13  
5 . 45  
5 . 10  
6 . 51  
3 . 18  
6 . 50  
4 . 16  
3 . 22  
Play  
2–16  
0.05  
Tr. Rate:  
128kbps  
transmission rate level  
DISPLAY  
1/2  
Exit  
Total playing time of disc, tracks and track times  
«
Display off  
MP3  
Information: MP3  
Folder  
001  
002  
Track  
1 ~ 9  
1 ~ 11  
1 ~ 3  
Folder  
01  
02  
Track  
1 ~ 10  
1 ~ 13  
1 ~ 5  
Notes  
• Depending on the format and type of disc being used, not all  
screens may be displayed.  
003  
03  
004  
005  
1 ~ 22  
1 ~ 15  
04  
05  
1 ~ 4  
1 ~ 8  
• When playing Video CDs in PBC mode or unfinalized CD-Rs not  
all the above information is displayed.  
DISPLAY Exit  
1/2  
Folders and number of tracks in each folder  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customizing the Function  
Settings  
The procedure on this page describes how to operate the  
menus on the Setup screen.These menus are used to set  
and adjust a number of system settings.The various  
functions that can be adjusted are covered throughout  
this manual.The procedure on this page provides a basic  
outline for using the Setup screen menus.  
DVD  
VCD  
CD  
MP3  
Using the Setup Screen Menus  
Press Open or Play on the unit or  
Open/Close or £ on the Remote  
controller to select DVD input.  
Use the cursor button (3) to enter  
the setting options.  
Example  
Unit  
6
1
ENTER  
Language  
Video1 V2  
General  
TV Screen — 16:9(Wide  
Component Video Interlace  
)
Progressive  
Auto Progressive  
Remote  
controller  
Select Interlace or Progressive  
output Component Video  
ENTER  
SETUP  
Move  
Exit  
Select  
• Not all menu options can be changed  
while a disc is playing. In these cases,  
the options appear grayed out on the  
screen and cannot be adjusted. To  
change these settings, press 7 first  
before pressing DVD SETUP.  
Press Setup/TV Input.  
The Setup screen appears.  
2
u
Example  
Language  
Video1 V2  
General  
TV Screen — 4:3(Letter Box)  
Component Video — Interlace  
• Operating the menu after pressing 7  
may cancel the resume function.  
• Some menu options are not immediately  
effective if set while a disc is playing. To  
make these settings effective, stop  
playback and then start again, or  
change the settings while the disc is  
stopped.  
Setup Video  
Adjust video format/quality  
SETUP  
Move  
Exit  
Use the cursor buttons (2/3) to  
select the menu you want.  
3
4
Use the cursor buttons (5/∞) to  
select a new setting and press  
ENTER to set the new setting in  
memory.  
Press Return or the cursor button (2) to  
exit the options without making any  
changes.  
ENTER  
As each menu is selected with the cursor,  
the settings appear below the menu  
heading.  
7
8
ENTER  
Use the cursor button (∞) to enter  
the menu.  
The top item within the menu becomes  
highlighted.  
ENTER  
Press Return or the cursor button  
(2) to go back to the main menu bar  
to select another menu.  
Example  
Language  
Video1 V2  
General  
4:3(Letter Box)  
4:3(Pan&Scan)  
16:9(Wide)  
TV Screen  
Component Video  
Press Setup/TV Input to close the  
Setup screen.  
The Setup screen closes.  
Select your display preference  
u
9
SETUP  
ENTER  
Move  
Exit  
Select  
Use the cursor buttons (5/∞) to  
select the setting you want to  
change.  
The options available for each setting  
appear to the right when the setting is  
selected. The current setting appears with  
the setting indicator lit.  
5
Notes  
EN
• If you turn off the DVD Receiver during setup, the settings are  
canceled. Press Setup/TV Input to finish the setup.  
• The memorized resume position may be erased by setup.  
• The Setup screen always shows the latest settings.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
Open/Close 0  
Sel  
o
l
2/3/5/∞  
ENTER  
Step  
/
Slow  
CH  
Tun  
ENTER  
VOL  
T-D/ST  
Muting  
Return  
Setup/TV Input  
Surround  
A.Control  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
/
RC-507  
M
DVD  
VCD  
CD  
MP3  
Using the Setup Screen Menus  
Changing to the Setup Screen “Expert”  
Menu Mode  
I When setting up for the first time  
The Setup screen menus are divided into two levels, [Basic]  
and [Expert], to make this unit more convenient to operate for  
different levels of users. The [Basic] menu mode contains  
functions that may be considered necessary for the basic  
operations of this DVD Receiver and helpful on-screen  
It is recommended to set up the DVD receiver using the Setup  
Navigator (page 30). If you selected [Auto Start Off] when the  
Setup Navigator appeared, you may still set up the DVD  
Receiver using the Setup Navigator in the General menu  
screen.  
i
information identified by the  
mark. The [Expert] menu mode  
If you choose not to use the Setup Navigator, be sure to make  
the necessary settings in the Setup screen Video 1, Video 2  
and Language menus as described on the following pages.  
Some DVDs start playing automatically when loaded in the  
DVD Receiver. If a DVD has been loaded, be sure to press 7  
before proceeding.  
adds to the [Basic] menu mode additional functions of the  
DVD receiver that can be adjusted to further personalize  
performance of the DVD receiver.  
In this manual, functions that are contained in the [Expert]  
menu mode are identified by the  
icon.  
Expert  
Make changes to the [Setup Menu Mode] setting in the Setup  
screen General menu.  
Note  
The next time you press Setup/TV Input, you’ll see the menu screen  
V2 Language General  
Video1  
that you exited from last time.  
Setup Menu Mode Expert  
Setup Navigator  
Basic  
Parental Lock — Off (us)  
I How to interpret the setting indicator colors  
in the Setup screen menus  
Change menu mode  
When setting up the system, or when making adjustments, it is  
convenient to know what settings are applicable to the  
different disc formats. When the settings appear for each  
menu option, the currently selected setting appears with the  
setting indicator highlighted in one of three colors: blue, green  
or yellow. These colors correspond to what formats the menu  
option effects as shown in the table below.  
SETUP  
ENTER  
Move  
Select  
Exit  
Settings: Expert  
Basic (Factory setting)  
Note  
On-screen information only appears in the [Basic] menu mode .  
Color of indicator  
Blue  
Disc format(s)  
DVD only  
Yellow  
Green  
DVD/Video CD  
All compatible formats  
Note  
If a setting applicable only to DVDs is changed while a Video CD or  
CD is loaded, a blue DVD icon appears in the upper right hand  
corner of the screen to indicate that the setting is not applicable to  
the currently loaded disc. The setting will be effective the next time a  
DVD is loaded.  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customizing the Function Settings  
Setting the TV Screen Size  
The width-to-height ratio of conventional TVs is 4:3, while the  
width-to-height ratio of wide screen and high-definition TVs is  
16:9. This width-to-height ratio is called the aspect ratio.  
When viewing software recorded in different aspect ratios, the  
image’s height to width ratio can be switched to match the TV  
or monitor being used.  
Make changes to the TV screen size in the [TV Screen] setting  
in the Setup screen Video 1 menu. Please note that changes  
to the [TV Screen] setting cannot be made when a disc is  
playing. Stop playback of the disc before attempting to make  
any changes.  
When viewing a wide screen TV or monitor  
DVD screen size format  
Setting and Appearance  
Wide screen format DVD  
Please note that there are some  
wide screen letter box formats  
that place black bars at the top  
and bottom of the screen. This is  
not a malfunction.  
“Wide” setting  
Standard screen format DVD  
When viewing a standard screen  
format DVD on a wide screen  
TV, black bars may be  
automatically placed at the side  
of the screen to adjust to the  
DVD format.  
Example  
Language  
Video1 V2  
General  
TV Screen 4:3(Letter Box)  
Component Video 4:3(Pan&Scan)  
“Wide” setting  
16:9(Wide  
)
Standard screen format DVD  
(unnatural stretched effect)  
If you are viewing a standard  
screen format DVD on a wide  
screen TV, the picture may  
appear “stretched” on the  
screen. To remedy this  
condition, change your wide  
screen TV to display a standard  
(4:3) screen. Refer to the  
instructions supplied with your  
wide screen TV or monitor for  
more information.  
Select your display preference  
SETUP  
Move  
Exit  
Settings: 4:3 (Letter Box)  
4:3 (Pan & Scan)  
16:9 (Wide) (Factory setting)  
“Wide” setting  
Notes  
• If [Standard (4:3)] is selected in the Setup Navigator screen, [4:3  
(Letter Box)] is selected on this screen. If you prefer the  
pan&scan format, change the settings on this screen.  
• Whether the aspect can be switched or not depends on the disc.  
Please refer to the information written on the disc jacket, etc.  
• Some discs may not include the screen format selected in the [TV  
Screen] setting. When this occurs, the standard TV screen format  
available on the disc is automatically selected.  
When viewing a standard size TV or monitor  
DVD screen size format  
Setting and Appearance  
Wide screen format DVD  
The Letter box presentation  
places black bars at the top and  
bottom portions of the screen to  
provide the full wide screen  
presentation of a movie on a  
standard TV (4:3 aspect ratio).  
I Differences in screen sizes and DVD  
“Letter Box” setting  
formats  
The number of screen size formats currently available can be  
somewhat confusing. If set incorrectly, the video presentation  
may not appear as it should. The following diagrams and  
descriptions are intended to help you set your TV screen size  
in a way that will allow you to fully enjoy the digital video of  
DVD.  
Wide screen format DVD  
The Pan & Scan presentation  
crops both sides of the wide  
screen presentation to use the  
full standard TV screen.  
“Pan & Scan” setting  
The settings in the [TV Screen] setting are perhaps most  
applicable when the DVD you are watching is programmed in  
the wide screen format. If you have a standard TV, select  
either [4:3 (Letter Box)] or [4:3 (Pan & Scan)] based on your  
personal preference. If you have a wide screen TV, select  
[16:9 (Wide)].  
Standard screen format DVD  
If you have a standard TV, the  
standard screen format will be  
presented regardless of the  
setting.  
Any setting  
Wide screen format DVD  
(unnatural squeezed effect)  
If you are viewing a wide screen  
format DVD on a standard TV  
and the [TV Screen] setting is  
set to [16:9 (Wide)], the picture  
may appear “squeezed” on the  
screen. To remedy this  
condition, select either [4:3  
(Letter Box)] or [4:3 (Pan &  
Scan)].  
“Wide” setting  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Video 1 Options  
Expert  
I
Connecting to a progressive scan-  
compatible TV  
I Switching the S-Video Output  
You can switch the kind of S-Video signal output from the S-  
Video outputs. If you connected your TV with an S-Video cord,  
in rare cases the TV picture may appear stretched. In this  
case switch the output from [S2] to [S1].  
Make changes in the [S-Video Out] in the Setup screen Video  
1 menu in the [Expert] menu mode (page 67).  
Compared to a standard interlaced TV picture, a progressive  
scan TV is capable of stable, flicker-free images.  
Set only if you connected the COMPONENT VIDEO OUT  
jacks to a progressive scan-compatible TV or monitor.  
Make changes to the [Component Video] setting in the Setup  
screen Video 1 menu.  
Example (Other than European model)  
Language  
Video1 V2  
General  
TV Screen — 16:9(Wide  
Component Video Interlace  
Language  
Video1 V2  
General  
TV Screen — 16:9(Wide)  
Component Video — S1  
)
Progressive  
Auto Progressive  
S-Video Out S2  
Screen Saver — On  
Select Interlace or Progressive  
output Component Video  
SETUP  
Move  
Exit  
SETUP  
Move  
Exit  
Settings: S1  
Settings: Interlace (Factory Setting)  
Use this setting with regular TVs that are not  
S2 (Factory Setting)  
compatible with progressive scan. Check the TV’s  
instruction manual if you are not sure about this.  
I Turning the Screen Saver On and Off Expert  
Progressive  
As a protective function against residual images on the TV  
screen or monitor, a phenomenon referred to as “screen burn”,  
the screen saver appears when the same screen has been  
displayed for a length of time. By default, the screen saver is  
turned on. However, the screen saver function can be turned  
on and off at your discretion.  
Use this setting with TVs and monitors that have  
progressive scan component video inputs. The  
Progressive indicator lights up. Check the TV’s  
instruction manual if you are not sure about this.  
Progressive indicator  
Make changes to the [Screen Saver] setting in the Setup  
screen Video 1 menu in the [Expert] menu mode (page 67).  
PROGRESSIVE SCAN  
Theater-Dimensional  
IPM  
Example (Other than European model)  
Language  
Video1 V2  
General  
TV Screen — 16:9(Wide)  
Component Video — Interlace  
S-Video Out — S2  
Auto Progressive  
Switches to progressive scan when 16:9 DVDs are  
played,4:3 DVDs uses interlace setting. Your TV/  
monitor must be compatible with progressive scan  
to use this setting.  
Screen Saver  
On  
Off  
SETUP  
Move  
Exit  
Tip  
Settings: On (Factory setting)  
• If this DVD Receiver is set to output progressive-scan video, it’s  
possible that the picture will appear stretched when playing discs  
recorded in 4:3 format. This happens when the TV’s aspect ratio  
is set at 16:9. To see the picture in its correct aspect ratio, change  
the TV setting to 4:3.  
Off  
If your TV can not be switched between 4:3 and 16:9, set this  
DVD Receiver to [Interlace] or [Auto progressive]. In Auto  
progressive mode, 4:3 discs will be played in Interlace mode,  
while discs that are recorded in both 4:3 and 16:9 will play in  
interlace mode during the 4:3 sections, and in progressive mode  
during the 16:9 parts. Switch your TV’s aspect ratio to the most  
suitable setting (for more details, see the manual that came with  
your TV). When set to [Auto Progressive], you may see picture  
disturbance when this DVD receiver (and the TV) switches  
between progressive and interlace modes. This is not a  
malfunction of either this DVD receiver or the TV. Picture  
disturbance should only occur when switching from a menu  
screen to the main feature, for example.  
• Progressive scan compatible TVs have on board progressive  
circuits. If you prefer, choose “Interlace” in this unit’s setup screen  
to view progressive scan video adjusted by the TV’s on board  
circuits.  
Notes  
• If you connect a TV that is not compatible with a progressive scan  
signal and choose one of the progressive scan settings, you will  
not be able to see any picture at all. With your TV connected  
using either the composite or S-Video terminals, choose the  
[Interlace] setting in the [Component Video] menu.  
Expert  
*
denotes more detailed settings. If the item is not displayed,  
please refer to page 67 to display it.  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customizing the Function Settings  
Adjusting the Video Quality  
You can either select a preprogrammed setting designed to  
match certain program types or make adjustments to match  
your own preferences and save them in the DVD receiver’s  
memory.  
Make changes to the [Video Adjust] setting in the Setup  
screen Video 2 menu.  
I Adjusting the picture quality settings  
– To create your own setting (1)  
1 Use the cursor button (3) to select [Start] then press  
ENTER.  
Language  
V1  
General  
Video2  
Background — Gray  
Video Adjust — Start  
Interlace Video Memory Select  
Interlace Video Setup  
Picture Quality Controls  
2 Use the cursor button (∞) to select [Video Setup] then  
press ENTER.  
SETUP  
Move  
Exit  
I Selecting a preprogrammed setting  
1 Use the cursor button (3) to select [Start] then press  
ENTER.  
Interlace Video Memory Select  
Interlace Video Setup  
Setting items vary depending on the settings in the Setup  
screen Video 1 menu.  
3 Use the cursor buttons (2/3) to select the setting to [On] or  
[Off].  
Interlace Video Memory Select  
Interlace Video Setup  
2 Press ENTER.  
DNR  
off  
max  
ENTER  
DISPLAY  
Check  
Move  
Select  
4 Use the cursor buttons (5/∞) to select the setting to adjust.  
You can adjust any or all of the following picture quality factors:  
Standard  
P.Memory 1  
Cinema  
Animation  
P.Memory 3  
<When set to [Progressive] or [Auto Progressive] in the  
P.Memory 2  
Setup screen Video 1 menu.>  
Standard (Factory Setting)  
Presents the video with no effect added.  
DNR  
Controls the amount of signal noise in the luminance component  
of the video signal.  
Sharpness  
Cinema  
Delivers a cinema-like picture.  
Adjusts the sharpness of the mid-frequency (less detailed)  
elements in the picture. (This setting is only effective when [Fine  
Focus] is [On].)  
Detail  
Switch on to reveal greater detail (higher resolution) in the  
picture.  
Chroma Delay  
Animation  
Provides images with bright clear colors.  
Memory 1, Memory 2, and Memory 3  
(P.Memory 1, P.Memory 2, and P.Memory 3)  
These are user programmable settings. See “Adjusting the  
picture quality settings” on this page and page 71 for more  
information.  
Adjusts how saturated colours appear.  
Gamma  
Adjusts the brightness of the darker images in the picture.  
Prog. Memory  
Program the current settings.  
3 Use the cursor buttons (2/3/5/∞) to select one of the  
preprogrammed picture quality settings.  
If there is a DVD or Video CD playing, the effects of each setting  
can be viewed while it is highlighted on the screen. This may be  
useful in selecting an appropriate setting.  
4 Press ENTER.  
The new selection is set.  
Notes  
• Each picture quality setting is defined by a number of individual  
settings, described in “Adjusting the picture quality settings” on  
this page and page 71.  
• Depending on the disc and the TV/monitor, you may not see the  
effect clearly.  
Expert  
*
denotes more detailed settings. If the item is not displayed, please refer to page 67 to display it.  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Video Quality  
<When set to [Interlace] in the Setup screen Video 1  
menu.>  
Fine Focus  
Switch [On] to reveal greater detail (higher resolution) in the  
picture.  
I Adjusting the picture quality settings  
– To create your own setting (2)  
1 Use the cursor button (3) to select [Start] then press  
ENTER.  
Contrast  
Adjusts the contrast of the elements in the picture.  
Sharpness  
Adjusts the sharpness of the high-frequency (detailed) elements  
in the picture. (This setting is only effective when [Fine Focus] is  
[On].)  
Interlace Video Memory Select  
Interlace Video Setup  
Chroma Level  
Adjusts how saturated colours appear.  
2 Use the cursor button (∞) to select [Video Setup] and press  
ENTER.  
3 Press Display.  
Hue  
Adjusts the overall colour balance between red and green. (This  
is only effective when the DVD receiver is connected using the  
VIDEO OUT or S-VIDEO OUT jacks.)  
Memory (Interlace Memory)  
Programs the current settings.  
DNR  
Sharpness  
Detail  
off  
max  
On  
Off  
2
min  
min  
green  
max  
max  
red  
Chroma Delay  
Gamma  
Memory  
5 Use the cursor buttons (2/3) to adjust the settings.  
Adjust these while a disc is playing to see the effect of changes  
immediately.  
Off  
1
3
6 Repeat steps 4 and 5 to make adjustments to other  
settings.  
4 Use the cursor buttons (5/∞) to select the setting and use  
the cursor buttons (2/3) to adjust the settings.  
Adjust these while a disc is playing to see the effect of changes  
immediately.  
5 To memorize the setting, select Memory 1, 2, 3, then press  
ENTER.  
If you would like to save the settings in the DVD receiver’s  
memory, be sure to select either [1], [2], or [3] in the [Prog.  
Memory] or [Memory (Interlace Memory)] setting to establish  
which memory location to save the new settings in. Please note  
that if you select a location where settings have already been  
saved, the old settings will be replaced by the new ones.  
The previous setting will be erased.  
Prog. Memory  
Move  
Off  
Select  
1
2
3
DISPLAY  
ENTER  
Check  
7 When you are finished making adjustments, press ENTER  
to establish the new settings.  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customizing the Function Settings  
Setting the Video 2 Options  
I Changing the Background of the Screen  
You can select a background to appear when the DVD  
Receiver is in the stop mode.  
Make changes to the [Background] setting in the Setup screen  
Video 2 menu.  
I Setting the Position of the On-screen  
Display Expert  
When watching conventional software on a wide screen TV,  
the operation display is at the very top of the screen, and may  
be difficult to see. Changing the position of the display lets you  
see operation indicators clearly even on a wide screen TV.  
Alternatively, you can choose to turn them off completely with  
the [Off] setting.  
Language  
V1  
General  
Video2  
Background Gray  
Video Adjust — Black  
Make changes in the [On Screen Display] in the Setup screen  
Video 2 menu in the [Expert] menu mode (page 67).  
Put Background Selections  
Language  
V1  
General  
Video2  
SETUP  
Move  
Exit  
Background — Gray  
Video Adjust  
Still Picture — Auto  
Settings: Gray  
Black  
On Screen Display Position-Wide  
Angle Indicator  
Position-Normal  
Off  
I Selecting the Type of Paused Image to  
SETUP  
Expert  
Move  
Exit  
Display  
This function lets you view a clear still-image when DVD  
playback is paused.  
Settings: Position-Wide  
Position-Normal (Factory setting)  
Make changes in the [Still Picture] setting in the Setup screen  
Video 2 menu in the [Expert] menu mode (page 67).  
Off  
Note  
Language  
V1  
General  
Video2  
This setting is only effective with DVDs that contain a 4:3 aspect  
ratio video presentation.  
Background — Gray  
Video Adjust —  
t
Still Picture Field  
On Screen Display  
Angle Indicator  
Frame  
Auto  
Expert  
I Turning the angle indicator on and off  
When a picture recorded in different angles is played back  
is displayed on the screen. This setting lets you see clearly  
whether the playback picture is recorded in multiple angles or  
not.  
Turn the angle indicator on or off in the [Angle Indicator]  
setting in the Setup screen Video 2 menu in the [Expert] menu  
mode (page 67).  
SETUP  
Move  
Exit  
Settings: Field (Picture shake will be eliminated during a  
paused picture.)  
Frame (Select to obtain higher picture quality.)  
Auto (Selects [Field] or [Frame] automatically  
according to the disc.) (Factory setting)  
Language  
V1  
General  
Video2  
Background — Gray  
Video Adjust  
Still Picture — Auto  
On Screen Display — Position-Normal  
Angle Indicator On  
Off  
SETUP  
Move  
Exit  
Settings: On (  
is displayed) (Factory setting)  
Off (Not Displayed)  
Note  
Even when the [Angle Indicator] setting is set to [Off], the  
indicator in the display panel of the DVD Receiver lights during multi-  
angle playback. Therefore, it is possible to know when the multi-  
angle function can be used without having to display the icon on the  
screen.  
Expert  
*
denotes more detailed settings. If the item is not displayed, please refer to page 67 to display it.  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Language Options  
DVDs have the capacity to contain a great deal of audio  
information, which includes the ability to hold up to 8 different  
language tracks and subtitle information in as many as 32  
different languages. This section outlines the variety of audio  
language and subtitle options available with this DVD receiver.  
Please note that if you have completed the Setup Navigator,  
the audio and subtitle language options have automatically  
been set in accordance with the [OSD Language] (the  
language that appears on the screen).  
I Selecting a subtitle language preference  
The subtitle language that you will normally display can be  
selected from the subtitles programmed on a disc. Even when  
the subtitle language is changed during playback by pressing  
Subtitle, the language selected at this setting will be selected  
when the disc is changed.  
Make changes to the [Subtitle Language] setting in the Setup  
screen Language menu.  
You cannot make this setting with a disc playing.  
Note  
DVDs differ in content and do not all contain multiple language or  
subtitle information. Therefore making settings in this section may  
have no effect on some DVDs.  
General  
Video1 V2 Language  
OSD Language  
Audio Language  
Subtitle Language  
Auto Language  
English  
French  
German  
Italian  
I Setting the On-screen Display (OSD)  
Spanish  
Other  
Language  
Setup disc's subtitle language  
SETUP  
This setting is used to establish the language that operation  
indicators and on-screen messages and operations display.  
Change this setting in the Setup screen Language menu [OSD  
Language] setting.  
Move  
Exit  
Settings: English (Factory setting)  
French  
German  
Italian  
General  
Video1 V2 Language  
OSD Language — English  
Audio Language  
Subtitle Language  
Auto Language  
français  
Deutsch  
Italiano  
Español  
Spanish  
Other (For details on how to select other languages,  
see “When [Other] is selected” on page 74).  
Select the On Screen Language  
Note  
SETUP  
Move  
Exit  
The menu settings may be different from those shown above.  
Settings: English (Factory setting)  
I Setting Auto Language to control subtitle  
and audio language based on program  
content  
When the Auto Language function is used, foreign movies are  
shown with the original audio soundtrack and subtitles in the  
language selected in the [Subtitle Language] menu option.  
Domestic films are shown with the original audio soundtrack  
and no subtitles. (This setting may not be effective with all  
DVDs.)  
français  
Deutsch  
Italiano  
Español  
Notes  
• The menu settings may be different from those shown above.  
• The [OSD Language] setting is factory set to [English]. If you  
want English to be displayed, it is not necessary to adjust this  
setting.  
I Selecting an audio language preference  
Make changes to the [Auto Language] setting in the Setup  
screen Language menu.  
You cannot make this setting with a disc playing.  
The audio language that you normally listen to can be  
selected from the various audio languages on a DVD. Even  
when the audio language is changed during playback by  
pressing Audio, the language selected at this setting will be  
selected as the default when the DVD is changed.  
Make changes to the [Audio Language] setting in the Setup  
screen Language menu.  
General  
Video1 V2 Language  
OSD Language  
Audio Language  
Subtitle Language  
Auto Language  
English  
—
—
—
English  
English  
On  
Off  
Play dialog, etc. in original language  
Subtitle ON with foreign audio  
You cannot make this setting with a disc playing.  
SETUP  
Move  
Exit  
General  
Video1 V2 Language  
OSD Language  
Audio Language  
Subtitle Language  
Auto Language  
English  
—
French  
German  
Italian  
Settings: On (Factory setting)  
Off  
Spanish  
Other  
Note  
Setup audio language  
The Auto Language function operates only when this function  
is set to [On], and the language set for the [Audio Language]  
and [Subtitle Language] settings is the same.  
SETUP  
Move  
Exit  
Settings: English (Factory setting)  
French  
German  
Italian  
Spanish  
Other (For details on how to select other  
languages, see “When [Other] is selected” on page  
74.)  
Note  
The menu settings may be different from those shown above.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
73  
Customizing the Function Settings  
Setting the Language Options  
Expert  
I Selecting a DVD menu language preference  
I Forcing subtitles to be displayed  
Expert  
Even when the subtitles are turned off, some DVDs will  
nevertheless display them on the screen. This setting allows  
you to select the language of the subtitles to be displayed with  
this type of DVD.  
Select [With Audio] to display the subtitles in the same  
language as the currently selected [Audio Language]. Select  
[Selected Subtitle] to display the subtitles in the language set  
in the [Subtitle Language] setting.  
In addition to containing different audio languages, DVD may  
also contain menu screens in different languages as well.  
Setting a DVD language preference, sets the selected  
language as a default when DVDs with menu information in  
that language are encountered.  
Selecting [w/ Subtitle Language] automatically assigns the  
language selected in the [Subtitle Language] setting.  
Make changes to the [DVD Language] setting in the Setup  
screen Language menu in the [Expert] menu mode (page 67).  
You cannot make this setting with a disc playing.  
Make changes to the [Subtitle Off] setting in the Setup screen  
Language menu in the [Expert] menu mode (page 67).  
You cannot make this setting with a disc playing.  
General  
Video1 V2 Language  
General  
Video1 V2 Language  
OSD Language  
Audio Language  
Subtitle Language  
Auto Language  
DVD Language  
Subtitle Display  
Subtitle Off  
English  
English  
English  
On  
English  
With Audio  
Selected Subtitle  
—
—
—
—
—
OSD Language  
Audio Language  
Subtitle Language  
Auto Language  
DVD Language  
Subtitle Display  
Subtitle Off  
w/ Subtitle Language  
English  
French  
German  
Italian  
Spanish  
Other  
SETUP  
Move  
Exit  
SETUP  
Move  
Exit  
Settings: With Audio  
Selected Subtitle (Factory setting)  
Settings: w/ Subtitle Language (Factory setting)  
English  
French  
German  
Italian  
Spanish  
I When [Other] is selected  
When you want to select one of the 136 languages as the  
main audio language, follow the steps below when the  
following screen appears.  
Other (For details on how to select other  
languages, see “When [Other] is selected” on this  
page).  
A language code list can be found on page 75.  
General  
Video1 V2 Language  
OSD Language  
Audio Language  
Subtitle Language  
Auto Language  
English  
French  
German  
Italian  
Notes  
• The menu settings may look different from the one shown above.  
• If this function is not effective, the languages that can be selected  
may also be selected in the DVD menu. Press Menu to open the  
DVD menu and make your selection accordingly.  
Spanish  
Other  
Setup audio language  
SETUP  
ENTER  
Move  
Select  
Exit  
I Selecting subtitles, assist subtitles or no  
1 Use the cursor buttons to select [Other] and press ENTER.  
The language selection screen appears.  
subtitles Expert  
General  
Audio Video1 V2 Language  
Audio Language  
Use this function to turn the subtitles on or off. Additionally,  
some DVDs provide assist subtitles that provide additional  
explanations of scenes in addition to the standard subtitles for  
viewers who are hard of hearing. Select [Assist Subtitle] to  
display these subtitles on DVDs where this function is offered.  
Make changes to the [Subtitle Display] setting in the Setup  
screen Language menu in the [Expert] menu mode (page 67).  
You cannot make this setting with a disc playing.  
List of Language  
Code (0~2)  
ja: Japanese  
1
0
0
1
Setup audio language  
RETURN  
ENTER  
–/+  
Move  
Return  
Exit  
SETUP  
Select  
2 Use the cursor buttons (2/3) to select either “List of  
Language” or “Code”.  
General  
Video1 V2 Language  
3 If you select “List of Language”, use the cursor buttons  
(5/∞) to select the language.  
OSD Language  
Audio Language  
Subtitle Language  
Auto Language  
DVD Language  
Subtitle Display  
Subtitle Off  
English  
English  
English  
On  
On  
Off  
—
—
—
—
For languages which are only shown as a code, refer to  
“Language Code List” on page 75.  
List of Languages  
ja: Japanese  
Assist Subtitle  
SETUP  
Move  
Exit  
Settings: On (Factory setting)  
Off  
If you select “Code”, use the cursor buttons (5/∞) to input  
the numbers of the input code.  
Assist Subtitle  
Notes  
Use the cursor buttons (2/3) to change the position of the  
cursor. You can also use the number buttons to enter the code.  
Code (0~2)  
• If there is no subtitle information recorded on the DVD, no  
subtitles are displayed even if this function is set to [On].  
• This setting serves as a default as whether or not to display  
subtitles. Even if this option is set to [Off], subtitles can be  
displayed by pressing Subtitle. Similarly, if this option is set to  
[On], the subtitles can be turned off by pressing Subtitle and then  
Clear.  
1
0
0
1
4 Press ENTER to set the new language.  
To exit the screen without making any changes, press Return.  
Expert  
*
denotes more detailed settings. If the item is not displayed, please refer to page 67 to display it.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
74  
Language Code List  
Language codes are used when setting the audio and subtitle  
5-language preferences (pages 73-74).  
Language  
Input-code  
Language  
Input-code  
Language  
Input-code  
Japanese (ja)  
English (en)  
French (fr)  
1001  
0514  
0618  
0405  
0920  
0519  
2608  
1412  
1620  
1922  
1821  
1115  
0512  
0101  
0102  
0106  
0113  
0118  
0119  
0125  
0126  
0201  
0205  
0207  
0208  
0209  
0214  
0215  
0218  
0301  
0315  
0319  
0325  
0401  
0426  
0515  
0520  
0521  
0601  
0609  
0610  
0615  
0625  
0701  
0704  
0712  
0714  
Gujarati (gu)  
Hausa (ha)  
0721  
0801  
0809  
0818  
0821  
0825  
0901  
0905  
0911  
0914  
0919  
0923  
1009  
1023  
1101  
1111  
1112  
1113  
1114  
1119  
1121  
1125  
1201  
1214  
1215  
1220  
1222  
1307  
1309  
1311  
1312  
1314  
1315  
1318  
1319  
1320  
1325  
1401  
1405  
1415  
1503  
1513  
1518  
1601  
1612  
1619  
1721  
Rhaeto-Romance (rm)  
Kirundi (rn)  
Romanian (ro)  
Kinyarwanda (rw)  
Sanskrit (sa)  
Sindhi (sd)  
1813  
1814  
1815  
1823  
1901  
1904  
1907  
1908  
1909  
1911  
1912  
1913  
1914  
1915  
1917  
1918  
1919  
1920  
1921  
1923  
2001  
2005  
2007  
2008  
2009  
2011  
2012  
2014  
2015  
2018  
2019  
2020  
2023  
2111  
2118  
2126  
2209  
2215  
2315  
2408  
2515  
2621  
Hindi (hi)  
German (de)  
Italian (it)  
Croatian (hr)  
Hungarian (hu)  
Armenian (hy)  
Interlingua (ia)  
Interlingue (ie)  
Inupiak (ik)  
Spanish (es)  
Chinese (zh)  
Dutch (nl)  
Sangho (sg)  
Serbo-Croatian (sh)  
Sinhalese (si)  
Slovak (sk)  
Slovenian (sl)  
Samoan (sm)  
Shona (sn)  
Portuguese (pt)  
Swedish (sv)  
Russian (ru)  
Korean (ko)  
Greek (el)  
Indonesian (in)  
Icelandic (is)  
Hebrew (iw)  
Yiddish (ji)  
Afar (aa)  
Javanese (jw)  
Georgian (ka)  
Kazakh (kk)  
Greenlandic (kl)  
Cambodian (km)  
Kannada (kn)  
Kashmiri (ks)  
Kurdish (ku)  
Kirghiz (ky)  
Somali (so)  
Albanian (sq)  
Serbian (sr)  
Siswati (ss)  
Sesotho (st)  
Sundanese (su)  
Swahili (sw)  
Tamil (ta)  
Abkhazian (ab)  
Afrikaans (af)  
Amharic (am)  
Arabic (ar)  
Assamese (as)  
Aymara (ay)  
Azerbaijani (az)  
Bashkir (ba)  
Byelorussian (be)  
Bulgarian (bg)  
Bihari (bh)  
Telugu (te)  
Latin (la)  
Tajik (tg)  
Lingala (ln)  
Thai (th)  
Laothian (lo)  
Lithuanian (lt)  
Latvian (lv)  
Tigrinya (ti)  
Turkmen (tk)  
Tagalog (tl)  
Setswana (tn)  
Tonga (to)  
Bislama (bi)  
Bengali (bn)  
Tibetan (bo)  
Breton (br)  
Malagasy (mg)  
Maori (mi)  
Catalan (ca)  
Corsican (co)  
Czech (cs)  
Macedonian (mk)  
Malayalam (ml)  
Mongolian (mn)  
Moldavian (mo)  
Marathi (mr)  
Malay (ms)  
Turkish (tr)  
Tsonga (ts)  
Tatar (tt)  
Welsh (cy)  
Twi (tw)  
Danish (da)  
Bhutani (dz)  
Esperanto (eo)  
Estonian (et)  
Basque (eu)  
Persian (fa)  
Finnish (fi)  
Ukrainian (uk)  
Urdu (ur)  
Maltese (mt)  
Burmese (my)  
Nauru (na)  
Uzbek (uz)  
Vietnamese (vi)  
Volapük (vo)  
Wolof (wo)  
Nepali (ne)  
Norwegian (no)  
Occitan (oc)  
Oromo (om)  
Oriya (or)  
Xhosa (xh)  
Fiji (fj)  
Yoruba (yo)  
Zulu (zu)  
Faroese (fo)  
Frisian (fy)  
Irish (ga)  
Panjabi (pa)  
Polish (pl)  
Scots-Gaelic (gd)  
Galician (gl)  
Guarani (gn)  
Pashto, Pushto (ps)  
Quechua (qu)  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customizing the Function Settings  
Setting the Parental Lock Level  
This DVD receiver lets you set the Parental Lock if the DVD  
has a parental lock level recorded on it. With Parental Lock  
capable discs, you can block access to material you feel is  
inappropriate for your children. Refer to the DVD jacket and  
the accompanying documentation to see if a particular disc  
contains a parental lock level.  
2 Use the cursor buttons (2/3) to move the cursor to a  
different position in the password.  
When all four numbers of the password have been entered, Enter  
appears on the screen.  
V2 Language General  
Video1  
Parental Lock: Register Code Number  
Make changes to the [Parental Lock] setting in the Setup  
screen General menu. Please note that changes to the  
Parental Lock level cannot be made when a disc is playing.  
Stop playback of the disc before attempting to make any  
changes.  
ENTER  
1
0
1
9
Enter 4—Digit Code  
RETURN  
SETUP  
Return  
Exit  
+/–  
Move  
You cannot select [Level] or [Country Code] until you have  
registered a password. Select [Password] to register a new  
password. See “Entering the password” on this page for how  
to register a new password.  
3 Press ENTER to set the password.  
The password is entered.  
Notes  
• Be sure not to forget your password. If you should forget it, reset  
the system, and enter a new password. To reset the system, see  
“Resetting the DVD Receiver to System Settings” (page 77).  
Please note that this procedure resets the system, and clears all  
saved settings, not just the password.  
V2 Language General  
Video1  
Setup Menu Mode — Basic  
Setup Navigator  
Parental Lock Password  
Level  
Country Code  
• Some discs lock out violent scenes. Refer to instruction notes on  
discs.  
Setup viewing restrictions  
SETUP  
Move  
Exit  
I Setting the Parental Lock Level  
Settings: Password  
Change the Parental Lock level to a higher or lower level  
according to the settings printed on the DVD disc jacket or  
accompanying documentation. If you use the Condition  
Memory function to save the settings for a particular disc, the  
Parental Lock level is saved as well. Because it is saved in  
memory, Parental Lock levels can be set for individual discs  
according to their content rather than a set level for all DVDs.  
1 Select [Level] in the [Parental Lock] setting and press  
ENTER.  
(For information, refer to “Entering the Password”  
on the this page.)  
Level  
(For information, refer to “Setting the Parental Lock  
Level” on this page.)  
Country Code  
(For information, refer to “Setting the Country Code”  
on the following page.)  
The screen changes to the password input screen. You cannot  
select [Level] until you have registered a password. To enter the  
password, refer to “Entering the Password” on this page.  
When a DVD with a set Parental Lock level is loaded  
Playback cannot be started until the code number has been correctly  
input by using the cursor buttons (2/3/5/∞) or the number buttons,  
and ENTER has been pressed.  
V2 Language General  
Video1  
Parental Lock: Level Change  
I Entering the Password  
1
Level  
2
3
4
5
6
7
8
Off  
Setup Parental Lock  
When you select either [Level] or [Country Code], it is  
necessary to register the password (4-digit code number).  
You’ll be asked to confirm your existing password before  
registering a new one. Use the following steps at any time you  
are asked to enter or confirm your password.  
RETURN  
SETUP  
Select  
Return  
Exit  
ENTER  
Move  
2 Use the cursor buttons (2/3) to adjust the Parental Lock  
Level.  
The lock icons appear “unlocked” up to the selected level to  
indicate that access is available.  
3 Press ENTER to set the new level.  
1 Use the cursor buttons (5/∞) or the number buttons to  
select a number between 0 and 9.  
You can also use the number buttons to enter the numbers  
directly. When entering your password for the first time, or  
changing it, you will be asked to reenter your password. When  
using the number buttons to confirm the password, the numbers  
appear as asterisks, and the cursor advances automatically to  
the next position.  
The new Parental Lock level is set and the screen returns to the  
General menu screen. To go back to the General menu screen  
without making any changes, press Return.  
I Changing the Password  
Change your password whenever you feel it is necessary.  
However, if you forget your existing password, you cannot  
enter this screen to change it.  
V2 Language General  
Video1  
Parental Lock: Register Code Number  
1 Select [Password Change] in the [Parental Lock] setting  
Enter 4—Digit Code  
and press ENTER.  
RETURN  
Return  
Exit  
+/–  
Move  
The screen changes to the password input screen. To enter the  
password, refer to “Entering the Password” on this page.  
2 Use the cursor buttons (2/3/5/∞) or the number buttons to  
enter the new password.  
ENTER  
3 When the new password has been entered, press ENTER.  
The new password is set and the screen returns to the General  
menu screen. To go back to the General menu screen without  
making any changes, press Return.  
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Country Code List  
I Setting the Country Code  
Change your Country Code whenever you feel it is necessary.  
However, if you forget your existing password, you cannot  
enter this screen to change it.  
1 Select [Country Code] in the [Parental Lock] setting and  
press ENTER.  
Country  
Input-code Country-code  
0118  
ar  
ARGENTINA  
AUSTRALIA  
AUSTRIA  
0121  
au  
0120  
at  
0205  
be  
BELGIUM  
The screen changes to the password input screen. To enter the  
password, refer to “Entering the Password” on the previous page.  
The Country Code selection screen appear.  
0218  
br  
BRAZIL  
0301  
ca  
CANADA  
General  
Video1 V2 Language  
Country Code  
0312  
cl  
CHILE  
0314  
cn  
CHINA  
List of Codes  
Code (0~2)  
0411  
dk  
DENMARK  
FINLAND  
us  
2
1
1
9
0609  
fi  
Setup Country Code  
0618  
fr  
FRANCE  
RETURN  
SETUP  
Return  
Exit  
+/–  
Move  
0405  
de  
GERMANY  
HONG KONG  
INDIA  
ENTER  
Select  
0811  
hk  
2 Use the cursor buttons (2/3) to select either “List of  
Codes” or “Code”.  
3 If you select “List of Codes”, use the cursor buttons (5/∞)  
0914  
in  
0904  
id  
INDONESIA  
ITALY  
0920  
it  
to select the country.  
For country codes which are only shown as a code, please refer  
to “Country Code List” on this page.  
1016  
jp  
JAPAN  
1118  
kr  
KOREA, REPUBLIC OF  
MALAYSIA  
MEXICO  
1325  
my  
List of Codes  
1324  
mx  
1412  
nl  
NETHERLANDS  
NEW ZEALAND  
NORWAY  
us  
1426  
nz  
1415  
no  
If you select “Code”, use the cursor buttons (5/∞) to input  
the numbers of the input code.  
Use the cursor buttons (2/3) to change the position of the  
1611  
pk  
PAKISTAN  
1608  
ph  
PHILIPPINES  
PORTUGAL  
RUSSIAN FEDERATION  
SINGAPORE  
SPAIN  
1620  
pt  
cursor. You can also use the number buttons to enter the code.  
1821  
ru  
Code (0~2)  
1907  
sg  
0519  
es  
2
1
1
9
1905  
se  
SWEDEN  
0308  
ch  
SWITZERLAND  
TAIWAN, PROVINCE  
OF CHINA  
4 Press ENTER to set the new Country Code.  
2023  
tw  
To exit the screen without making any changes, press Return.  
2008  
th  
THAILAND  
UNITED KINGDOM  
UNITED STATES OF  
AMERICA  
0702  
gb  
2119  
us  
Resetting the DVD Receiver to System  
Settings  
To reset the DVD Receiver section of this unit, press and  
hold 7 on the front panel when pressing Standby/On to  
turn the unit from standby to on.  
All program memory, saved settings from functions such as  
Last Memory and Condition Memory are cleared, TV System  
is reset to AUTO and all Setup screen menus are returned to  
factory settings.  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controlling a TV connected  
to the DVD Receiver  
RC-507M remote controller able to operate a product from  
another brand.  
By learning a pre-programming code, you can make the  
Pre-programming codes  
Note:  
Caution  
If more than one code is given in the table, try the code one by  
one until you reach the code for your component (i.e. if the first  
code does not work, then try the next).  
With some brand’s components, some buttons may not work  
correctly. In this case, program the command separately.  
BRAND  
SETTING No.  
AIWA  
100, 101  
AKAI  
102, 103, 104  
en  
AUDIOSONIC  
BELL & HOWELL  
BLAUPUNKT  
BRIONVEGA  
CENTURION  
COLTINA  
CORONAD  
CROWN  
105  
106  
107  
108, 109  
110  
111, 112, 113  
114  
Se  
l
o
Mode TV  
l
Step/Slow  
CH  
Tun  
ENTER  
VOL  
t
T-D/ST  
Muting  
Surround  
A.Control  
115, 116  
DAEWOO  
DUAL  
EMERSON  
FENNER  
117, 118, 119, 120, 121  
122  
123, 124, 125, 126, 127  
128, 129  
Repeat  
A-B  
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last  
M
Program Random  
Clear  
SP Setup  
Test Tone  
CH Sel  
FERGUSON  
FISHER  
FUNAI  
130, 131  
132  
133, 134, 135  
1
SW Mode  
4
2
Distance  
5
3
6
Up/Down  
9
Number  
buttons  
IPM  
7
T-D Setup  
8
+10  
-- ---  
0
Search  
Enter  
+10  
/
RC-507  
M
FUJITSU GENERAL 136, 137, 138  
GE  
139, 140, 141  
GOLDSTAR  
GOODMANS  
GRUNDIG  
HITACHI  
HYPER  
142, 143  
144  
145, 146  
147, 148, 149, 150  
Learning a pre-programming code  
151  
INNO HIT  
IRRADIO  
JVC  
KENDO  
KTV  
152  
103  
Find the 3-digit number for the  
1
153, 154, 155, 156, 157  
158  
159, 160  
161  
brand name of the component that  
you want to operate in the table on  
this page.  
LUXOR  
MAGNAVOX  
MARANTZ  
MARK  
MATSUI  
MITSUBISHI  
MIVAR  
NEC  
NOKIA  
OCEANIC  
NORDMENDE  
OKANO  
162, 163  
164  
165  
166, 167, 168, 169  
170, 171, 172, 173  
174, 175  
176, 177  
178, 179, 180, 181  
181  
182, 183  
152  
184, 185, 186  
187, 188, 189, 190  
152, 162, 191  
192, 193  
Turn on the component that you  
2
want to operate.  
While holding down Mode TV, press  
3
the +10 button, and then release  
both buttons.  
The Send indicator lights when the Mode  
+
10  
-- --  
TV button is pressed and turns off when  
the +10 button is pressed. Wait until the  
indicator turns off before releasing both  
buttons. The Send indicator lights again.  
/
ORION  
PANASONIC  
PHILIPS  
PIONEER  
PROSCAN  
QUASAR  
RADIO SHACK  
RCA  
SABA  
SAMSUNG  
SANYO  
194  
195  
196  
Within 10 seconds, enter the 3-digit  
code number.  
The Send indicator flashes twice slowly. If  
the Send indicator quickly flashes three  
times, then either an incorrect 3-digit code  
was entered or an incorrect operation was  
performed. If this occurs, return to step 3.  
4
SP Setup  
Test Tone  
CH Sel  
3
1
SW Mode  
4
2
Distance  
5
110, 141, 197, 198, 199, 200  
182, 183, 201  
202, 203, 204, 205, 206, 207, 208  
209, 210, 211, 212  
103  
213  
6
Up/Down  
9
-
T
IPM  
7
D Setup  
8
0
SCHNEIDER  
SEARS  
SELECO  
SHARP  
SONY  
SYMPHONIC  
TELEFUNKEN  
THOMSON  
TOSHIBA  
UNIVERSUM  
ZENITH  
214, 215  
216, 217  
218, 219, 220, 221, 222, 223  
224, 225  
201, 226, 227  
228  
213, 229  
230  
Press the button that you  
programmed and check if the  
system operates correctly.  
• If the component does not operate  
properly, return to step 3 and repeat the  
steps above.  
5
231, 232  
78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
en  
On  
Standby  
Sel  
o
e
Step/Slow  
CH  
Tun  
ENTER  
VOL  
CH +/–  
VOL %/fi  
t
Setup/TV Input  
Muting  
-
T
D/ST  
Muting  
Surround  
A.Control  
-
B
Repeat  
A
Late Night  
Audio  
Timer  
Angle  
Subtitle FM Mode  
Last M  
Program Random  
Clear  
SP Setup  
1
SW Mode  
Test Tone  
CH Sel  
2
Distance  
5
3
Number  
buttons  
4
IPM  
7
6
Up/Down  
9
-
T
D Setup  
8
+
10  
-- ---  
0
Search  
Enter  
Enter  
/
-
RC 507  
M
Controlling TV  
Press the Mode TV button.  
The TV button lights green.  
1
2
Press the desired operation button.  
The buttons shaded in the figure to the left  
are the operation buttons that can be used  
to control your television.  
The buttons given below have operations programmed  
into them.  
On:  
Turns on the TV  
Standby:  
CH +/–:  
Turns off the TV  
Moves up and down the television channels  
Setup/TV Input: Switches the TV/VCR input for the television  
0,1 to 9, +10:  
Enter:  
Numeric keys  
Confirm  
VOL %/fi:  
Muting:  
Adjusts the volume at the television  
Activates the muting function at the television  
Note  
You can use the grayed buttons in the illustration to control the DVD  
receiver in thism mode.  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording Using the Connected Equipment  
Note  
You can record according to the following using the connected  
recording equipment:  
• Sound/picture of discs played back by the DVD Receiver,  
• Sound of FM/AM programs, and  
Many discs and sources are copy protected. Copy protected sources  
are impossible to record.  
• Sound/picture of the connected source.  
Basic Recording Procedure  
I Digital recording from the source connected  
to the digital input connectors to the digital  
recording equipment connected to the  
digital output connector  
The digital input connector is the DIGITAL OPTICAL IN jack.  
Select TV/LINE with the Input selector.  
The digital output connector is the DIGITAL OPTICAL OUT  
connector.  
Set the recording equipment (MD  
1
recorder, DAT, Cassette tape deck,  
VCR, DVD recorder, CD recorder,  
etc.) to recording pause.  
Select the input source to be  
recorded, then set it to play pause.  
• To play and pause a DVD video, Video  
CD, or audio CD, see page 29.  
2
Recording digital sound signals from sources connected to the  
digital input connectors using digital recording equipment  
connected to the digital output is possible unless:  
• The recording is against SCMS (Serial Copy Management  
System) rules (for details of SCMS rules, refer to the  
manual of the digital recording equipment),  
• To select an FM/AM program, see page  
35.  
• To select a connected source, see page  
38.  
• The digital signals are in bitstream format (the recordable  
digital signal format is PCM –– two channel digital stereo  
sound signals), or  
Refer to the manuals of the connected  
source equipment for instructions on how  
to play and pause.  
• The sampling frequency is out of the recordable range of  
the recording equipment (for recordable sampling  
frequency, refer to the manual of the digital recording  
equipment). 96/88.2 kHz digital audio signals are not  
output from copy protected discs.  
Select Stereo mode to record in analog  
from the unit’s DVD to other equipment.  
True DTS signals cannot be recorded in  
analog.  
Release the recording pause set in  
I Analog recording from a DVD Video played  
3
step 1 to start recording.  
DVD  
using the DVD Receiver  
The digital sound signals are converted to analog signals and  
output to the analog output jacks unless the DVD video is  
recorded in the DTS Surround.  
Start playback of the selected  
source in step 2.  
4
Although the speakers can reproduce DTS Surround sounds,  
DTS signals are not output to the analog output jacks.  
Notes  
• If you select another input source during recording, the selected  
source will be recorded.  
• Sound effects described on pages 46 to 51 do not affect the  
recorded sounds.  
80  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Check the following guide for the possible cause of a problem before contacting service. Refer also to the respective  
instruction manuals of the connected components and TV.  
Symptoms  
Causes  
Remedies  
Pages  
The DVD Receiver doesn’t • The power cord is disconnected.  
• Check the connection of the power cord.  
• Firmly connect the power cord to the  
unit's AC INLET.  
24  
24  
switch on.  
• The power cord has slipped out of the  
unit's AC INLET.  
• There is external noise interfering with the • Switch off the Standby/On then switch it on  
24  
computer circuits of the DVD Receiver.  
again. If not recovered, disconnect the power  
cord, then connect it again.  
No sound is reproduced.  
• The muting function is activated.  
• The DVD Receiver is not properly  
connected.  
• Deactivate the muting function.  
• Check the connections to the DVD  
Receiver.  
40  
16-22  
• The amplifier protection circuitry has  
activated. (The Standby indicator flashes.)  
• Contact your nearest Integra/Onkyo  
service center.  
—
• Headphones are connected.  
• The volume is low.  
• Decrease the volume, then disconnect the 40  
headphones.  
• Use the Master Volume to turn up the  
40  
volume.  
No sound or very little  
sound is reproduced from  
the center speaker.  
• The speakers are not properly connected. • Check the speaker connections.  
• The listening mode is set to “STEREO” or • No sound is reproduced from the center  
17  
46, 49  
“ORCHESTRA.”  
speaker when the listening mode is  
“STEREO” or “ORCHESTRA.”  
• Adjust the volume level of the center  
speaker.  
• The volume level of the center speaker  
(“CENTER”) is set to minimum.  
28  
26  
• A speaker configuration without the center • Check that the selected speaker  
speaker is selected.  
configuration includes the center speaker.  
No picture appears on the  
TV screen.  
• The TV is not set to receive the output  
signals from the DVD Receiver.  
• The video connection cable is not  
connected securely.  
• Set the TV to the DVD Receiver’s input.  
Refer to the instruction manual of TV.  
• Check the connections between the DVD 16  
Receiver and TV set.  
—
The sound of the playback • Another input source is selected.  
source is not heard.  
• Select the appropriate input source.  
38  
24  
The buttons on the remote • Power supply fluctuations or other  
• Switch off the Standby/On, then switch it on  
again. If not recovered, disconnect the power  
cord, then connect it again.  
controller and DVD  
Receiver do not operate.  
abnormalities such as static electricity  
may interrupt correct operation.  
The disc tray comes back  
out automatically, shortly  
after the disc tray is closed. • The disc is dirty or warped.  
• Region number does not conform with  
• The disc is not placed properly on the disc • Use the disc tray guide to align the disc.  
31  
tray.  
• Refer to “Notes on Discs”.  
8, 9  
4
• If the region number on the disc does not  
match the number on the DVD receiver,  
the disc cannot be used.  
this unit.  
The DVD Receiver does  
not start playback.  
• No disc is inserted.  
• Insert a disc. (Check that “DVD,” “VCD,”  
or “CD” is lit in the DVD Receiver’s  
display.)  
31  
• An unplayable disc is inserted.  
• The disc is placed upside down.  
• Check the playable discs.  
• Place the disc with the playback side  
down.  
8
31  
• The disc is not placed within the disc tray  
guide.  
• The disc is dirty.  
• Place the disc within the proper guide on  
the disc tray.  
• Eject the disc and clean it.  
• Deactivate the parental lock function or  
change the parental lock level.  
31  
9
76  
• The parental lock function is activated.  
The playback picture is  
occasionally distorted.  
• The disc is dirty.  
• It is in fast forward or fast reverse  
playback.  
• Eject the disc and clean it.  
• Sometimes a small amount of picture  
distortion may appear. This is not a  
malfunction.  
9
—
Brightness is unstable or  
noise is visible on the  
playback picture.  
• Copy protection is activated.  
• Connect the DVD Receiver directly to the 16  
TV. Avoid connecting the DVD Receiver to  
the TV through a VCR.  
The picture from the DVD  
Receiver doesn’t appear  
on the TV screen.  
• The TV is not set to receive the output  
signals from the DVD Receiver.  
• The DVD Receiver is not properly  
connected.  
• Set the TV to the DVD Receiver’s input.  
—
• Check the connections to the DVD  
Receiver.  
16  
Settings are canceled.  
• When the power is turned off by power  
failure or by unplugging the power cord,  
settings will be canceled.  
• Before unplugging the power cord, press  
Standby/On.  
—
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Symptoms  
Causes  
Remedies  
Pages  
Playback doesn’t follow the • The DVD Receiver is in repeat playback  
• Resume normal playback.  
54, 56-60  
course of the disc’s  
programs.  
mode, memory playback mode, or  
random playback mode, etc.  
The buttons on the remote • Power supply fluctuations or other  
• Switch off the Standby/On, then switch it  
on again. If not recovered, disconnect the  
power cord, then connect it again.  
24  
controller and DVD  
abnormalities such as static electricity  
may interrupt correct operation.  
Receiver do not operate.  
mark appears on  
screen.  
• The selected function does not operate  
for that disc.  
–
29  
29  
63  
mark appears on  
screen.  
• The operation is prohibited by the DVD  
receiver.  
–
When making changes in  
the Setup screen menus,  
is displayed.  
• There is a Video CD, CD or MP3 loaded  
in the DVD receiver and the setting that  
was changed only applies to DVD  
performance.  
• The setting will be effective the next time  
a DVD is loaded.  
Some settings in the Setup • The [Setup Menu Mode] is set to [Basic].  
Menu do not appear.  
• Set the [Setup Menu Mode] to [Expert].  
• Press £ or to exit the pause mode.  
67  
No sound is reproduced.  
• The pause mode is engaged.  
• The volume level of TV or DVD receiver is • Increase the volume level.  
29  
40  
set to minimum.  
The screen is stretched or  
aspect does not change.  
• The multi aspect setting is not  
appropriate.  
• Change the aspect setting in the [TV  
68  
Screen] setting in the Setup screen Video  
1 menu to the screen type most  
appropriate to the TV or monitor you are  
using.  
• The TV is connected with an S-video  
cord.  
• If you connected your TV with an S-Video 69  
cord, in rare cases the TV picture may  
appear stretched. In this case switch the  
output from [S2] to [S1]  
The disc containing the  
MP3 tracks won’t play.  
• The disc is not ISO 9660 compatible.  
• Files are not MPEG1 Audio Layer 3  
format, 44.1 or 48 kHz, fixed bit-rate.  
• Check the disc.  
• Check the file format.  
8
8
Some MP3 tracks appear  
to be missing from a disc.  
• The track name does not end in “.mp3” or • This system will not recognize file that  
8
8
“.MP3”.  
does not end in ".mp3" or ".MP3" as an  
MP3 track. Change the track name.  
• This DVD Receiver only recognizes the  
first 250 folders and tracks on a disc. If  
there are more folders/tracks than this,  
you will not be able to play them.  
• More than 251 folders and tracks are  
recorded on a disc.  
• A multi-session disc is inserted.  
• This DVD Receiver is not compatible with  
multi-session discs. If the disc is multi-  
session, you will only be able to play  
tracks recorded onto the first session.  
• Be sure to make MP3 CD with fixed bit-  
rate setting.  
8
8
• The disc contains variable bit-rate MP3  
file.  
82  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Symptoms  
Causes  
Remedies  
Pages  
Too much noise is heard or • FM stereo waves may produce a hiss  
• Switch the frequency receiving mode to  
mono.  
• Adjust the position, height, and direction  
of the FM antenna.  
• Connect an FM outdoor antenna. Try to  
use an antenna with more elements.  
(For installation of the outdoor antenna,  
consult your nearest dealer as it requires  
special skills and experience.)  
35  
sound is interrupted  
occasionally. (The FM  
STEREO indicator does  
not light steadily.)  
noise when a certain level is reached.  
• The position or direction of the FM  
antenna is incorrect.  
22, 23  
22, 23  
• The station is too weak.  
The sound is distorted or  
sound volume decreases.  
• The radio wave is distorted.  
• Cars are running or airplanes are flying  
near the house.  
–
–
—
—
Sound is excessively  
distorted.  
• There is a tall building or a mountain  
nearby.  
–
—
(The waves transmitted from the  
transmission center (direct waves) and  
the waved reflected by buildings or  
mountains (diffraction waves) interfere  
with each other causing multi pass  
distortion.)  
No preset channels are  
selected.  
• The power cord is unplugged, or the main  
power is switched off, for a long time.  
• The preset data in memory is lost. Preset 35  
the radio stations again.  
Sound is reproduced from  
the speakers but not  
recorded.  
• The sound system you are trying to  
record is DTS Surround.  
• DTS Surround sound is unable to be  
recorded.  
—
47  
38  
Late Night function cannot  
be used.  
• Playback source is not Dolby Digital  
encoded.  
• Check that the Dolby Digital indicator  
lights up on the display.  
An z connected  
component cannot be  
controlled by the remote  
controller.  
• The signal input is not compatible.  
• Use the Input Selector to select the  
correct input.  
• The z cable is not firmly connected to  
the jack.  
• Firmly connect the z cable. Also connect 20  
the components using audio connection  
cables.  
IR IN is connected but the  
remote controller will not  
control the unit.  
• It is not connected correctly.  
• Check that the Connecting block and IR  
receiver are correctly connected.  
21  
• An object is between the remote controller • Remove any objects blocking the IR  
and the IR receiver.  
receiver.  
• The remote controller is not operating  
correctly.  
• Check the operation of the remote  
controller as indicated below.  
Playback timer or  
Recording timer function  
does not operate.  
• The current time is not set correctly.  
• The playback timer is set to "off".  
• Reset the current time.  
41  
45  
—
• Set the playback timer to "on".  
• The recording medium is not compatible.  
• Make sure there is an MD, CDR or Tape  
inserted in the recording component. Also  
check that the timer is set correctly.  
• No batteries are inserted in the remote  
controller.  
• The batteries are worn out.  
• Insert new batteries.  
15  
The buttons on the DVD  
Receiver operate but the  
buttons on the remote  
• Replace with new batteries.  
15  
15  
• The remote controller is not pointed at the • Point the remote controller at the remote  
controller don not operate.  
remote sensor of the DVD Receiver.  
• The remote controller is too far from the  
DVD Receiver.  
sensor of the DVD Receiver.  
• Operate the remote controller within 5 m  
(16 feet).  
15  
12  
• Any wrong Mode button is pressed.  
• Press the appropriate Mode button.  
This unit contains a sensitive microcomputer, which under certain circumstances might fail to operate due to excessive noise  
interference. If this happens, press the DVD Receiver’s Preset Memory button and Standby/On button at the same time until  
“CLEAR” appears in the DVD Receiver’s display. The DVD Receiver turns into the standby mode, then all the custom settings  
for the receiver section of the DVD Receiver will be erased. Please repeat the custom settings from the beginning.  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
AMPLIFIER SECTION  
Power Output (FTC)  
All channels 25 watts per channel min.  
Damping Factor  
40 at 8 ohms  
RMS. into 6 ohms two channel driven,  
1,000 Hz with no more than 10% total  
harmonic distortion.  
Input Sensitivity and Impedance  
DIGITAL OPTICAL IN  
–21 to –15 dBm  
200 mV/50 kohms  
LINE (TV/LINE, MD/CDR/TAPE)  
Continuous power output (DIN)  
All channels 21 watts per channel min.  
Output Level and Impedance  
DIGITAL OPTICAL OUT  
REC OUT (MD/CDR/TAPE)  
RMS. into 6 ohms two channel driven,  
1,000 Hz  
–21 to –15 dBm  
200 mV, 2.2 kohms  
1 V, 470 ohms  
Continuous Power output (EIAJ)  
PRE OUT (SUBWOOFER)  
All channel 26 watts per channel min.  
RMS. into 6 ohms two channel driven,  
1,000 Hz  
Frequency Response  
Acoustic Control  
20 to 30,000 Hz : +/– 0.8 dB  
1: +9 dB at 82 Hz  
2: +9 dB at 82 Hz  
+6 dB at 10,000 Hz  
100 dB (0.5 V INPUT LINE)  
–50 dB  
Total Harmonic Distortion 10 % at rated power  
0.2 % at 1 watt output  
10 % at rated power  
0.2 % at 1 watt output  
Signal-to-noise Ratio  
Muting  
IM Distortion  
DVD SECTION  
Signal readout system  
Linear velocity  
Laser  
Semiconductor laser, wavelength  
650 nm (DVD) / 780 nm (CD)  
10 Hz to 44 kHz (96 kHz)  
Optical non-contact  
3.49 m/s (Single Layer)  
3.84 m/s (Dual Layer)  
Frequency response  
Signal-to-noise ratio (digital audio)  
Audio dynamic range (digital audio)  
Harmonic distortion (digital audio)  
Wow and flutter  
Operating conditions  
More than 100 dB  
More than 93 dB  
Less than 0.025%  
Error correction system Reed Solomon Product Code  
Signal system Standard NTSC  
Regional restriction code South American area: 1  
Below threshold of measurability  
Temperature: 5°C to 35°C (41°F to 95°F),  
Operation status: Horizontal  
Output Level and Impedance  
Composite  
S-Video  
1.0Vp-p, 75 ohms  
Y: 1.0 Vp-p, 75 ohms  
C: 0.286 Vp-p, 75 ohms  
Y: 1.0 Vp-p, 75 ohms  
PB, PR: 0.7 p-p, 75 ohms  
Component  
TUNER SECTION  
Tuning Range  
FM: 87.50 to 108.00 MHz (50 kHz steps)  
AM: 530 to 1710 kHz (10 kHz steps)  
Usable Sensitivity  
FM: Mono  
11.2 dBf, 1.0 µV (75 ohms IHF)  
0.9 µV (75 ohms DIN)  
17.2 dBf, 2.0 µV (75 ohms IHF)  
23 µV (75 ohms DIN)  
Stereo  
AM: 30 µV  
FM: Mono  
Stereo  
50 dB Quieting Sensitivity  
17.2 dBf, 2.0 µV (75 ohms)  
37.2 dBf, 20.0 µV (75 ohms)  
Capture Ratio  
Image Rejection Ratio  
FM: 2.0 dB  
FM: 40 dB  
AM: 40 dB  
FM: 90 dB  
AM: 40 dB  
FM: Mono  
Stereo  
Harmonic Distortion  
FM: Mono  
Stereo  
AM:  
0.2 %  
0.3 %  
0.7 %  
IF Rejection Ratio  
Signal-to-noise Ratio  
73 dB, IHF  
67 dB, IHF  
Frequency response  
Stereo Separation  
FM: 30 to 15,000 Hz (+/– 1.0 dB)  
FM: 45 dB at 1,000 Hz  
AM: 40 dB  
30 dB at 100 to 10,000 Hz  
Alternate Channel Att. (+/– 400 kHz) FM: Mono  
55 dB, IHF  
Stereo Threshold  
Output  
FM: 17.2 dBf,  
FM: 500 mV  
AM: 150 mV  
20 µV (75 ohms)  
Selectivity  
AM Suppression Ratio  
FM: 50 dB, DIN 55dB, IHF  
FM: 50 dB  
GENERAL  
Power Supply  
AC 120 V, 60 Hz  
: 130 W  
Dimensions (W x H x D) 435 × 81 × 366 mm (171/8 × 33/16 × 147/16 ins.)  
Weight 7.0 kg (15.4 lb.)  
Power Consumption  
Power Consumption (standby mode) : 2.0 W  
: 29 W (*)  
(*) when clock display is on  
Specifications and features are subject to change without notice.  
84  
Download from Www.Somanuals.com. All Manuals Search And Download.  
85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
86  
Download from Www.Somanuals.com. All Manuals Search And Download.  
87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Integra Division of  
ONKYO U.S.A. CORPORATION  
18 park Way, Upper Saddle River, N.J. 07458, U.S.A.  
Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com  
Integra Division of  
ONKYO CORPORATION  
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN  
Tel: 072-831-8111 Fax: 072-833-5222  
Printed in Japan  
W0207-1  
SN 29343408  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Refrigerator BIAAAXXXX User Manual
InFocus Cordless Drill DS 14DAL User Manual
InStep Stroller SB100 User Manual
InStep Stroller SB150 User Manual
Jacuzzi Hot Tub EA40 User Manual
Jet Tools Saw JWBS 14OCS User Manual
JVC Stereo System CA MXK10R User Manual
Jwin MP3 Player JX CD492 User Manual
Jwin MP3 Player JX MP101 User Manual
Kolcraft Stroller S59 R1 User Manual