V3
FINAL
FOR PRINT
NS-A700PF6_A700PF6-2_A8001F6_A8001F6-2_LT600B-2_DA2920_DA2920-2_14-1039_QSG_V3_EN.ai 1 9/16/2014 4:29:05 PM
|
Quick Setup Guide NS-A700PF6/NS-A700PF6-2/NS-A8001F6/NS-A8001F6-2/NS-LT600B-2/NS-DA2920/NS-DA2920-2
Refrigerator Filter
Congratulations on your purchase of one of the highest performing
water filters on the market today. Insignia filters use a high-grade
coconut carbon that has 50% more micro-pores than standard
carbon. They also use fewer high-compression binders, giving you the
best water filtration possible.
NS-A700PF6 or NS-A700PF6-2 (LG)
NS-LT600B-2 (LG and Kenmore)
1 Press the push button on the filter housing.
2 Gently pull the cartridge down and then pull it out
of the filter housing. You may need to lower or
remove the shelf below the cover.
3 Ensure that o-rings are present on the cartridge
and are seated into grooves.
4 Insert the new cartridge, pushing it in until it stops.
Push up firmly and close the cover.
5 Reset the filter change indicator in your refrigera-
tor, if applicable. (See“RESETTING YOUR FILTER
INDICATOR”on back page.)
Note: Run approximately 1.5 gallons of water through
the new filter before use.
1 Remove the old filter by rotating a half turn
counterclockwise, then pull it out. The water
automatically turns off.
2 If you have a Kenmore refrigerator, check if there is
a plastic or metal cap that covers the top of the old
filter. If there is, pull off the cap and attach it to
your new filter. If there is not, continue to step 3.
3 Align the top of your new filter with the receiver,
then push it in until it stops.
PACKAGE CONTENTS
•
•
Refrigerator filter(s) (1 or 2 pack)
Quick Setup Guide
C
M
4 Rotate the filter a half turn clockwise to secure the
filter, then twist a little more to prevent leaks.
GENERAL INSTALLATION GUIDELINES
Y
1 YOU MUST SOAK your new filter in water for 15 minutes prior to
installing it in your refrigerator. This is needed to remove air from
the carbon block.
CM
MY
CY
CMY
K
NS-DA2920 or NS-DA2920-2 (Samsung)
1 Remove the old filter by rotating it a 1/4 turn
counterclockwise, then pull it out.
2 Align the top of your new filter with the receiver,
then push it up until it stops.
2 It is normal for black carbon fines (particles) to appear on the outside
of your filter. This happens when the filter is jarred in shipping, it is
safe, simply wipe it off.
3 Connections on our filters are larger in size to prevent leakage. This
might require more hand leverage to install.
4 After installing, run about two to three gallons of water through your
refrigerator’s water dispenser to remove air and loose carbon pieces.
The water may be cloudy and sputter until the air is removed.
5 We apply a safe, NSF approved, food grade silicone lubricant to our
filter connectors (jelly like substance).
NS-A8001F6 or NS-A8001F6-2 (Maytag, PuriClean II, Amana,
Sears/Kenmore, Whirlpool and Kitchenaid)
1 Twist the old filter counterclockwise and pull it out
of the receiver. The water automatically shuts off.
2 Push the new filter into the filter receiver until it
stops.
3 Rotate the filter a 1/4 turn clockwise to secure the
filter.
3 Turn the new filter clockwise until it stops.
4 Reset the filter change indicator in your refrigerator,
if applicable. (See“RESETTING YOUR FILTER
INDICATOR”on back page.)
Installation:
*PUSH AND TURN HARD
To remove turn counter-clockwise
To install turn clockwise
Do not remove the O-ring
Filter receivers are designed to be flexible.
Don’t worry, they won’t break!
BEFORE USING YOUR FILTER
If your refrigerator has a change filter indicator, reset it. See“Resetting your
filter indicator”for instructions.
Notes:
• Run approximately 1.5 gallons of water through the
new filter before use.
• Do not remove O-ring.
Before using your new product, please read these instructions to prevent any damage.
Download from Www.Somanuals.com. All Manuals Search And Download.
|