Ingersoll Rand Sprinkler 99828618 User Manual

OPERATOR’S MANUAL  
SB30X-XXX-X  
RELEASED:  
REVISED:  
(REV. G)  
2-18-00  
5-27-10  
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE  
3" SHOCK BLOCKER®  
METALLIC PULSATION DAMPENER  
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,  
OPERATING OR SERVICING THIS EQUIPMENT.  
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.  
SERVICE KITS  
Refer to the Model Description Chart to match the pump material  
options.  
637330-3X for repair of the diaphragms and “Orings (see page 4).  
PUMP DATA  
Models. . . . . . . . . . . . . . . . . see Model Description Chart for “-XXX-X”  
Pulsation Dampener Type . . . . . . . . . . . . . Metallic  
Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . see Model Description Chart  
Weight . . . . SB30X-XAX-X . . . . . . . . . . . . . . 41 lbs (18.6 kgs)  
SB30X-XCX-X . . . . . . . . . . . . . . 94 lbs (42.6 kgs)  
SB30X-XSX-X. . . . . . . . . . . . . . . 96 lbs (43.5 kgs)  
Material Inlet / Outlet  
SB30X-AXX-X . . . . . . . . . . . . . . 3 - 8 N.P.T.F. - 1  
SB30X-BXX-X . . . . . . . . . . . . . . Rp 3 (3 - 11 BSP parallel)  
Air Inlet (female) . . . . . . . . . . . . . . . . . . . . . . . 3/4 - 14 N.P.T.  
Maximum Air Inlet Pressure . . . . . . . . . . . 120 p.s.i.g. (8.3 bar)  
Maximum Material Inlet Pressure. . . . . . 120 p.s.i.g. (8.3 bar)  
Maximum Temperature Limits (diaphragm / seal material)  
E.P.R. / EPDM . . . . . . . . . . . . . . . . . . . . -60° to 280° F (-51° to 138° C)  
Nitrile . . . . . . . . . . . . . . . . . . . . . . . . . . . 10° to 180° F (-12° to 82° C)  
Santoprene® . . . . . . . . . . . . . . . . . . . . -40° to 225° F (-40° to 107° C)  
PTFE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40° to 225° F (4° to 107° C)  
Viton®. . . . . . . . . . . . . . . . . . . . . . . . . . . -40° to 350° F (-40° to 177° C)  
Maximum Fluid Volume . . . . . . . . . . . . . . . 367 in.3 (6.01 lit.)  
Dimensional Data. . . . . . . . . . . . . . . . . . . . . . see page 7  
Figure 1  
MODEL DESCRIPTION CHART  
SB30 X - X X X - X  
Air Section Material  
A - Aluminum  
S - Stainless Steel  
NOTICE: All possible options are shown in the chart, however, certain  
combinations may not be recommended, consult a representative or  
the factory if you have questions concerning availability.  
Fluid Connection  
A - 3 - 8 N.P.T.F. - 1  
B - Rp 3 (3 - 11 BSP, parallel)  
Fluid Cap Material  
A - Aluminum  
C - Cast Iron  
S - Stainless Steel  
Hardware Material  
P - Carbon Steel  
S - Stainless Steel  
Diaphragm Material  
A - Santoprene  
G - Nitrile  
T - PTFE / Santoprene  
V - Viton  
Fluid Section Service Kit Selection  
SB30X - XXX - X  
637330 - 3 X  
Diaphragm  
EXAMPLE: Model #SB30A-BAP-G  
Fluid Section Service Kit # 637330-3G  
INGERSOLL RAND COMPANY LTD  
209 NORTH MAIN STREET – BRYAN, OHIO 43506  
(800) 495-0276 FAX(800) 892-6276  
CCN 99828618  
© 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GENERAL DESCRIPTION  
FLUID SECTION DISASSEMBLY  
1. Remove (107) reducing bushing.  
2. Remove six (26) screws, releasing two (4) flanges and (11) “O”  
rings.  
3. Remove eight (27) screws and (29) nuts, releasing (15) fluid cap.  
4. Secure (14) screw in a vise, with (101) air valve body upward.  
5. Using a 15/16” socket on (186) screw, unthread and remove  
(186) screw and (10) washer.  
6. Remove (68) air cap from (7) diaphragm and components.  
7. Remove (14) screw from the vise. Unthread and remove (1) rod,  
releasing (2) stopper, (5) back-up washer, (196) cushion, (7) or (7  
and 8) diaphragms, (6) washer, (3) “O” ring and (9) washer from  
(14) screw.  
8. Remove four (131) screws, releasing (101) air valve body from  
the (68) air cap.  
The ARO® shock blocker pulsation dampener is designed to work  
with 1:1 ratio pumps having an outlet pressure not exceeding 120  
p.s.i. (8.3 bar). The shock blocker will effectively reduce material  
pressure variations, surges and shock to piping and delivery in fluid  
systems during pump reversal. It can significantly contribute to  
pulse reduction in low pressure spray applications.  
Accurate selection of wetted material will assure longest service life  
and minimize down time. Several material options are available for  
the body and diaphragm materials. Fluid section materials avail-  
able include: aluminum, cast iron and stainless steel. For specific  
fluid compatibility, consult the chemical manufacturer.  
The shock blocker uses a single air pressurized, flexible diaphragm  
working against the fluid line pressure. Several diaphragm material  
options are available to allow custom matching to the fluid mate-  
rial for best compatibility (refer to the model description chart).  
Shock blocker units can also be added in series to provide addi-  
tional dampening on the material.  
9. Remove (144) “Ucup from (68) air cap.  
10. Remove (103) sleeve from (101) air valve body.  
Pressure relief through the exhaust port is a normal compensating  
function of the control valve in the shock blocker. It will automati-  
cally adjust itself to the required operating pressure once the mate-  
rial pressure has been applied. The pressure supplied to the shock  
blocker needs to be equal to the material pressure to provide the  
proper dampening effect.  
FLUID SECTION REASSEMBLY  
Clean and inspect all parts. Replace worn or damaged parts  
with new parts as required. Lubricate all replacement parts and  
metallic moving parts with Lubriplate® FML-2 grease upon re-  
assembly.  
y
1. Grease and assemble two (172) “Orings to (103) sleeve.  
2. Assemble (103) sleeve into the (101) air valve body.  
3. Grease and assemble (70 and 173) “O” rings to (101) air valve  
body.  
AIR AND LUBE REQUIREMENTS  
EXCESSIVE AIR PRESSURE. Can cause pulsation  
WARNING  
dampener damage, personal injury or property damage.  
A filter capable of filtering out particles larger than 50 microns  
should be used on the air supply. There is no lubrication re-  
quired other than the “O” ring lubricant which is applied during  
assembly or repair.  
If lubricated air is present, make sure that it is compatible with  
the “Orings and seals in the air motor section of the pump.  
4. Grease and assemble (144) “Ucup into (68) air cap.  
5. Assemble (101) air valve body to (68) air cap.  
6. Assemble four (131) screws, securing (68) air cap. NOTE: Tighten  
(131) screws to 20 - 30 ft lbs (27.1 - 40.7 Nm).  
7. Assemble (9) washer, (3) “O” ring, (6) washer, (7) or (7 and 8)  
diaphragms, (196) cushion, (5) back-up washer and (2) stopper  
to (14) screw. NOTE: For models with PTFE diaphragms: Item  
(8) Santoprene diaphragm is installed with the side marked  
“AIR SIDE” towards the pump center body. Install the PTFE dia-  
phragm (7) with the side marked “FLUID SIDE” towards the (15)  
fluid cap.  
8. Assemble (1) rod to (14) screw.  
9. Grease and assemble two (173) “Orings to (1) rod.  
10. Place this assembly into (68) air cap.  
11. Assemble (10) washer and (186) screw into (101) air valve body  
and thread into (1) rod. Clamp (14) screw in a vise, with (186)  
screw upward, and tighten (186) screw to 65 - 70 ft lbs (88.1 -  
94.9 Nm).  
12. Remove assembly from the vise and assemble to (15) fluid cap,  
securing with eight (27) screws and (29) nuts. NOTE: Tighten (27)  
screws to 60 - 70 ft lbs (81.3 - 94.9 Nm).  
y
y
OPERATION  
DO NOT EXCEED 120 P.S.I. (8.3 BAR). Operating  
CAUTION  
at higher pressure can cause explosion, resulting in property  
damage or severe injury.  
Pressure relief through the exhaust port is a normal compen-  
sating function of the control valve in the shock blocker. It will  
automatically adjust itself to the required operating pressure  
once the material pressure has been applied.  
Operate the system for a few minutes to equalize air and fluid  
chambers of the pulsation dampener.  
y
y
PARTS AND SERVICE KITS  
Refer to the part views and descriptions as provided on pages 4  
and 5 for parts identification and Service Kit information.  
13. Grease and assemble two (11) “Orings to two (4) flanges.  
14. Assemble two (4) flanges to (15) fluid cap, securing with six (26)  
screws. NOTE: Tighten (26) screws to 60 - 70 ft lbs (81.3 - 94.9  
Nm).  
15. Apply Lubriplate FML-2 grease to threads of (101) air valve  
body. Apply PTFE tape to threads of (107) reducing bushing  
and assemble to (101) air valve body.  
Certain ARO “Smart Parts” are indicated which should be avail-  
able for fast repair and reduction of down time.  
y
y
MAINTENANCE  
Provide a clean work surface to protect sensitive internal mov-  
ing parts from contamination from dirt and foreign matter dur-  
ing service disassembly and reassembly.  
Keep good records of service activity and include pump in pre-  
ventive maintenance program.  
Before disassembling, empty captured material in the fluid cap  
by tipping the pulsation dampener on end.  
y
y
Viton® is registered trademarks of the DuPont Company Santoprene® is a registered trademark of Monsanto Company, licensed to Advanced Elastomer Systems, L.P.  
y
y
y
Lubriplate® is a registered trademark of Lubriplate Division (Fiske Brothers Refining Company) ARO® and Shock Blocker® are registered trademarks of Ingersoll-Rand Company  
y
y
y
SB30X-XXX-X (en)  
Page 3 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS LIST / SB30X-XXX-X  
Indicates parts included in 637330-3X service kit. Service kit also includes 94276 Lubriplate FML-2 grease packet.  

DIAPHRAGM OPTIONS SB30X-XXX-X  
SB30X-XXX-A  
Qty Part No. [Mtl] Part No.  
637330-3A 637330-3G  
SB30X-XXX-G  
[Mtl] Part No.  
637330-3T  
SB30X-XXX-T  
[Mtl] Part No.  
637330-3V  
SB30X-XXX-V  
(size)  
Item Description  
[Mtl]  
Service Kit  
Diaphragm  
Diaphragm  

7
8
(1) 94091-A  
(1) - - - - -  
[Sp] 94091-G  
- - - - - - - -  
[B] 94090-T  
- - - 94110-A  
[B] Y328-248  
[T] 95345  
[Sp] - - - - -  
[V]  
- - -  
[V]  


(1/8" x 5" o.d.)  
11 "O" Ring  
(2) 95187  
[E] Y325-248  
[T] Y327-248  

AIR SECTION PART OPTIONS SB30X-XXX-X  
Aluminum  
SB30A-XXX-X  
Qty Part No. [Mtl] Part No.  
Stainless Steel  
SB30S-XXX-X  
(size)  
Item Description  
[Mtl]  
[SS]  
[SS]  
[SS]  
[SS]  
[SS]  
5
Back-up Washer  
(1) 94831-1  
(1) 94030-3  
(1) 94839  
[C] 94831-2  
[A] 94031-4  
[A] 94843  
68 Air Cap  
101 Air Valve Body  
107 Reducing Bushing  
(1-1/2 - 11-1/2 N.P.T. male x 3/4 - 14 N.P.T. female)  
(1) Y45-22-C  
(2) - - - - -  
[I]  
Y45-322-T  
(5/32" o.d. x 3/4" long)  
181 Roll Pin  
- - - Y178-56-S  
MATERIAL CODE  
FLUID CAP MATERIAL OPTIONS SB30X-XXX-X  
[A]  
=
=
=
=
=
=
=
=
=
=
=
=
=
=
Aluminum  
Nitrile  
Aluminum  
Cast Iron  
Stainless Steel  
SB30X-XSX-X  
[B]  
[Br]  
[Bz]  
[C]  
[CI]  
[Co]  
[D]  
[E]  
Brass  
Bronze  
Carbon Steel  
Cast Iron  
Copper  
Acetal  
SB30X-XAX-X  
SB30X-XCX-X  
(size)  
Item Description  
Qty Part No.  
[Mtl] Part No.  
[Mtl] Part No.  
[Mtl]  
[SS]  
[SS]  
[SS]  
(N.P.T.F.)  
Flange  
(2) 94846  
(2) 94846-1  
(1) 94024  
[A] 94847  
[A] 94847-1  
[A] 94106  
[CI] 94940  
[CI] 94940-1  
[CI] 94107  
4
(BSP)  
E.P.R.  
[I]  
Iron  
Santoprene  
Stainless Steel  
PTFE  
15 Fluid Cap  
[Sp]  
[SS]  
[T]  
[V]  
Viton  
EXTERNAL HARDWARE OPTIONS SB30X-XXX-X  
Carbon Steel  
Stainless Steel  
SB30X-XXP-X  
SB30X-XXS-X  
(size)  
Item Description  
Qty Part No.  
[Mtl] Part No.  
[C] 94412-2  
[C] 94991  
[C] 95053  
[Mtl]  
[SS]  
[SS]  
[SS]  
(M12 x 1.75 - 6g x 45 mm)  
26 Screw  
27 Screw  
(6) 94412-1  
(8) 94991-1  
(8) 95053-1  
(M12 x 1.75 - 6g x 60 mm)  
(M12 x 1.75 - 6h)  
29 Nut  
COMMON PARTS  
(size)  
(size)  
Item Description  
Qty Part No.  
[Mtl]  
[C]  
Item Description  
Qty Part No.  
(4) Y325-111  
(1) 94836  
[Mtl]  
[B]  
(3/32” x 5/8” o.d.)  
1
2
3
6
9
Rod  
(1) 94941  
70 “O” Ring  
103 Sleeve  
Stopper  
“O” Ring  
Washer  
(1) 94837  
[D]  
[Bz]  
[C]  
(1/8” x 1” o.d.)  
(M10 x 1.5 - 6g x 30 mm)  
(1) Y328-210  
(1) 94942  
[T]  
131 Screw  
(4) 94845  

(3/16” x 1-3/8” o.d.)  
[SS]  
[SS]  
[SS]  
[SS]  
[C]  
144 “U” Cup  
172 “O” Ring  
173 “O” Ring  
(1) Y186-51  
(2) Y325-24  
(3) Y330-117  
(1) Y5-105-C  
(1) 94631  
[B]  



(13/16” i.d. x 2” o.d.)  
(1/16” x 1-1/4” o.d.)  
(3/32” x 1” o.d.)  
Washer  
(1) Y13-12-T  
(1) 93065  
[B]  
(0.630” i.d. x 1.687” o.d.)  
10 Washer  
[B]  
(3/4” - 16 x 2-1/2”)  
(5/8” - 18 x 1”)  
14 Screw  
(1) Y5-131-T  
(1) Y254-178-Z  
(1) 93004  
186 Screw  
[C]  
(1/4” - 20 x 1/2”)  
19 Screw, Self-Tapping  
43 Ground Lug  
196 Cushion  
201 Muffler  
[Sp]  
[Br]  

[Co]  
(1) 20312-1  
Page 4 of 8  
SB30X-XXX-X (en)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS LIST / SB30X-XXX-X  
ASSEMBLY TORQUE REQUIREMENTS  
)
(
NOTE: DO NOT OVERTIGHTEN FASTENERS.  
107  
186  
(14) screw, 65 - 70 ft lbs (88.1 - 94.9 Nm).  
(26) screws, 60 - 70 ft lbs (81.3 - 94.9 Nm).  
(27) screws, 60 - 70 ft lbs (81.3 - 94.9 Nm).  
(131) screws, 20 - 30 ft lbs (27.1 - 40.7 Nm).  
10  
Apply Lubriplate FML-2 grease  
LUBRICATION / SEALANTS  
101  
19  
Apply Lubriplate FML-2 grease (94276) to all “O” rings, “U”  
cups and mating parts.  
c
d
Apply anti-seize compound to threads and bolt and nut  
flange heads which contact pump case when using stain-  
less steel fasteners.  
43  
201  
NOTE: Lubriplate FML-2 is a white food grade petroleum grease.  
c
173  
3
1
c
c
172  
70  
c
144  
103  
5
7
8
6
181  
d
29  
68  
2
4
131  
173  
)
Torque Sequence  
c
View for SB30X-XXX-T (PTFE diaphragm) configuration only.  
1
2
8
Santoprene  
5
7
PTFE  
196  
7
6
COLOR CODE  
Diaphragm  
Color  
Material  
Nitrile  
Black  
Tan  
Santoprene  
c
3
Santoprene (back-up) Green  
PTFE  
Viton  
White  
Yellow (-)  
9
(-) Dash  
14  
11  
)
d
c
d
26  
4
26  
)
(
d
(
c
15  
27  
11  
4
Figure 3  
SB30X-XXX-X (en)  
Page 5 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TYPICAL CROSS SECTION  
Figure 4  
TROUBLE SHOOTING  
No dampening effect or erratic performance.  
Air bubbles in product discharge.  
y
y
Check for diaphragm rupture.  
Check connections of the pump’s suction plumbing.  
Check tightness of (14) diaphragm screw.  
y
y
y
Check for blocked or restricted outlet hoses.  
Check the air supply. Make certain the air pressure to the shock  
blocker is equal to the fluid pressure.  
Fluid leakage:  
- from exhaust port.  
Check for diaphragm rupture.  
Constant air leakage:  
- from exhaust port.  
y
- from flange.  
Check for damaged (172 and 173) “Orings.  
Check for damaged (11) “Oring.  
y
y
y
- from air cap.  
Check the tightness of (26) screws.  
Check the tightness of (27) screws.  
- from fluid cap.  
y
Check air pressure to the valve block (relieve fluid pressure).  
Check the tightness of (27) screws.  
Check for cracks. Discontinue use.  
y
y
y
Page 6 of 8  
SB30X-XXX-X (en)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIMENSIONAL DATA  
Dimensions shown are for reference only, they are displayed in inches and millimeters (mm).  
3/4 - 14 N.P.T. Air inlet  
15”  
(381 mm)  
10-7/8(276 mm)  
20-5/8(524 mm)  
3 - 8 N.P.T.F. - 1 or  
Rp 3 (3 - 11 BSP parallel)  
15”  
(381 mm)  
Figure 5  
SB30X-XXX-X (en)  
Page 7 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PN 97999-867  
Page 8 of 8  
SB30X-XXX-X (en)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Freezer TZA 1 User Manual
Insignia TV Cables NS DG06501 User Manual
Intel Server R1304GL4DS9 User Manual
Jacuzzi Hot Tub EE60 User Manual
Jenn Air Dishwasher DW700 User Manual
Jensen Car Stereo System HD5313 User Manual
JVC Car Speaker CS VS601 User Manual
JVC Digital Camera GR DVX PRO User Manual
Kenwood Stereo System XD A3 User Manual
KitchenAid Electric Grill KBSS361T User Manual