PE03P-X-X-A0S
OPERATOR’S MANUAL
RELEASED:
REVISED:
(REV. 04)
6-7-06
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
5-14-10
3/8” DIAPHRAGM PUMP
1:1 RATIO, NON-METALLIC
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to Model Description Chart to match the pump material options.
637428 for air section repair (see page 6).
637429-XX for fluid section repair (see page 4).
PUMP DATA
Models . . . . . . . . . . . . see Model Description Chart for “-XXX”.
Pump Type . . . . . . . . . Air Operated Double Diaphragm.
Material . . . . . . . . . . . . see Model Description Chart.
Weight . . . PE03P-XDS-XXX-A0S . . . 3.74 lbs (1.70 kgs)
PE03P-XES-XXX-A0S . . . 3.84 lbs (1.74 kgs)
PE03P-XKS-XXX-A0S . . . 4.08 lbs (1.85 kgs)
Figure 1
PE03P-XLS-XXX-A0S . . . 4.20 lbs (1.91 kgs)
PE03P-XPS-XXX-A0S . . . 3.02 lbs (1.37 kgs)
MODEL DESCRIPTION CHART
PE03P-XRS-XXX-A0S . . . 3.08 lbs (1.40 kgs)
Maximum Air Inlet Pressure . . . . . . . . . 100 p.s.i.g. (6.9 bar)
Maximum Material Inlet Pressure . . . . . 10 p.s.i.g. (0.69 bar)
PE03 P - X X S - X X X - A0S
Maximum Outlet Pressure . . . . . . . . . . 100 p.s.i.g. (6.9 bar)
Air Consumption @ 40 p.s.i. . . . . . . . . . 1 c.f.m. / gallon (approx.)
Maximum Flow Rate (flooded inlet) . . . . . 10.6 g.p.m. (40.1 l.p.m.)
Displacement / Cycle @ 100 p.s.i. . . . . 0.022 gallons (0.083 lit.)
Maximum Particle Size . . . . . . . . . . . . 1/16” dia. (1.6 mm)
Maximum Temperature Limits (diaphragm / ball / seat material)
Acetal . . . . . . . . . . . . . . . . . 10_ to 180_ F (-12 to 82_ C)
HytrelR . . . . . . . . . . . . . . . -20_ to 150_ F (-29_ to 66_ C)
Polypropylene . . . . . . . . . . . 35_ to 175_ F (2_ to 79_ C)
KynarR PVDF . . . . . . . . . . . 10_ to 200_ F (-12 to 93_ C)
SantopreneR . . . . . . . . . . . -40_to225_F (-40_to 107_C)
PTFE . . . . . . . . . . . . . . . . . 40_ to 225_ F (4_ to 107_ C)
VitonR . . . . . . . . . . . . . . . . -40_to350_F (-40_to 177_C)
Groundable Models . . . . . . . . . . . . . . . PE03P-XDS-XXX-A0S
PE03P-XES-XXX-A0S
Center Section Material
P - Polypropylene
Fluid Connection
A - 3/8 - 18 N.P.T.F. - 1
B - Rp 3/8 (3/8 - 19 BSP)
Fluid Caps / Manifold Material
D - Groundable Acetal (single port)
E - Groundable Acetal (multiple port)
K - Kynar PVDF (single port)
L - Kynar PVDF (multiple port)
P - Polypropylene (single port)
R - Polypropylene (multiple port)
Hardware Material
S - Stainless Steel
Dimensional Data . . . . . . . . . . . . . . . . see page 8
Seat Material
Noise Level @ 70 p.s.i., 60 c.p.m. . . . . . 72.7 db(A)
D - Acetal
P - Polypropylene
S - Stainless Steel
K - Kynar PVDF
The pump sound pressure levels published here have been updated to an Equivalent
Continuous Sound Level (L ) to meet the intent of ANSI S1.13-1971, CAGI-PNEU-
Ball Material
Aeq
ROP S5.1 using four microphone locations.
A - Santoprene
C - Hytrel
T - PTFE
V - Viton
NOTICE:Allpossibleoptionsareshowninthecharthowevercertaincom-
binations may not be recommended, consult a representative or the fac-
tory if you have questions concerning availability.
S - Stainless Steel
Diaphragm Material
A - Santoprene
C - Hytrel
T - PTFE / Santoprene
V - Viton
FLUID SECTION SERVICE KIT SELECTION
PE03P - ARS - S X X - A0S
637429 - X X
EXAMPLE: Model # PE03P-ARS-SAA-A0S
Fluid Section Service Kit # 637429-AA
Ball
Diaphragm
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET -- BRYAN, OHIO 43506
(800) 276-4658 D FAX (800) 266-7016
E2010
CCN 15262421
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL DESCRIPTION
OPERATING INSTRUCTIONS
The ARO diaphragm pump offers high volume delivery even at low air
pressure and a broad range of material compatibility options available.
Refer to the model and option chart. ARO pumps feature stall resistant
design, modular air motor / fluid sections.
Air operated double diaphragm pumps utilize a pressure differential in
theairchamberstoalternatelycreatesuctionandpositivefluidpressure
in the fluid chambers, ball checks insure a positive flow of fluid.
Pump cycling will begin as air pressure is applied and it will continue to
pump and keep up with the demand. It will build and maintain line pres-
sure and will stop cycling once maximum line pressure is reached (dis-
pensing device closed) and will resume pumping as needed.
S Always flush the pump with a solvent compatible with the material
being pumped ifthe materialbeingpumpedissubjectto“settingup”
when not in use for a period of time.
S Disconnecttheairsupplyfromthepumpifitistobeinactiveforafew
hours.
S Theoutletmaterialvolumeisgovernednotonlybytheairsupplybut
alsobythematerialsupplyavailableattheinlet.Thematerialsupply
tubing should not be too small or restrictive. Be sure not to use hose
which might collapse.
S When the diaphragm pump is used in a forced-feed (flooded inlet)
situation, it is recommended that a “Check Valve” be installed at the
air inlet.
S Secure the diaphragm pump legs to a suitable surface to insure
against damage by vibration.
AIR AND LUBE REQUIREMENTS
WARNING EXCESSIVE AIR PRESSURE. Can cause pump
damage, personal injury or property damage.
MAINTENANCE
S Afiltercapableoffilteringoutparticleslargerthan50micronsshould
beusedontheairsupply. Thereisnolubricationrequiredotherthan
the “O” ring lubricant which is applied during assembly or repair.
S Iflubricatedairispresent,makesurethatitiscompatiblewiththe“O”
rings and seals in the air motor section of the pump.
S Certain ARO “Smart Parts” are indicated which should be available
for fast repair and reduction of down time.
S Provide a clean work surface to protect sensitive internal moving
partsfromcontaminationfromdirtandforeignmatter duringservice
disassembly and reassembly.
S Keep good records of service activity and include pump in preven-
tive maintenance program.
S ServiceKitsare availabletoservicetwo separate DiaphragmPump
functions: 1. AIR SECTION, 2. FLUID SECTION. The Fluid Section
is divided further to match typical active MATERIAL OPTIONS.
TYPICAL CROSS SECTION
Figure 2
S HytrelR and VitonR are registered trademarks of the DuPont Company S KynarR is a registered trademark of Arkema Inc. S
S Santoprene R is a registered trademark of Monsanto Company, licensed to Advanced Elastomer Systems, L.P. S LubriplateR is a registered trademark of Lubriplate Division (Fiske Brothers Refining Company) S
PE03P-X-X-A0S (en)
Page 3 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST / PE03P-X-X-A0S FLUID SECTION
K 637429-XXFLUIDSECTIONSERVICEKITSinclude:Balls(seeBALLOPTION, referto -XXinchartbelow), Diaphragms(SeeDIAPHRAGMOPTION, refer
to -XX in chart below) and item 19 (listed below), plus items 144, 174 and 94276 LubriplateR grease (page 6).
SEAT OPTIONS
PE03P-XXS-XXX-A0S
“21”
BALL OPTIONS
PE03P-XXS-XXX-A0S
L “22” (5/8” o.d.)
MATERIAL CODE
[A] = Aluminum
[B] = Nitrile
[D] = Acetal
[E] = E.P.R.
[GA] = Groundable Acetal
[GFN] = Glass Filled Nylon
[H] = Hytrel
[K] = Kynar PVDF
[P] = Polypropylene
[PPG] = Glass Filled
Polypropylene
-XXX Seat
Qty [Mtl]
-XXX Ball
Qty [Mtl]
-XXX Ball
Qty [Mtl]
-DXX 96580-2
-KXX 96580-3
-PXX 96580-1
-SXX 96537
(4)
(4)
(4)
[D]
[K]
[P]
-XAX 96481-A
-XCX 96481-C
-XSX 96513
(4) [Sp]
-XTX 96481-4
-XVX 96481-3
(4)
(4)
[T]
[V]
(4)
[H]
(4) [SS]
(4) [SS]
[Sp] = Santoprene
[SS] = Stainless Steel
[T] = PTFE
[V] = Viton
DIAPHRAGM OPTIONS PE03P-XXS-XXX-A0S
L SERVICE KIT
-XX = (Ball)
-XXX -XX = (Diaphragm)
L “7”
L “8”
L “19”
“O” Ring
Diaphragm Qty [Mtl] DiaphragmQty [Mtl] (3/32” x 1-1/8” o.d.) Qty [Mtl]
-XXA 637429-XA
-XXC 637429-XC
-XXT 637429-XT
-XXV 637429-XV
96533-A
96533-C
96538
(2) [Sp] - - - - -
- - -
- - -
- - - 93761
- - - Y325-119
(4)
(4)
(4)
(4)
[E]
[B]
[T]
[V]
(2)
(2)
(2)
[H] - - - - -
[T] 96533-A
[V] - - - - -
(2) [Sp] 96514
- - - - - - Y327-119
96558
MANIFOLD / FLUID CAP OPTIONS PE03P-XXS-XXX-A0S
Polypropylene
PE03P-XPS- PE03P-XRS-
Qty Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No. [Mtl]
Kynar PVDF
Groundable Acetal
PE03P-XKS- PE03P-XLS-
PE03P-XDS-
PE03P-XES-
Item Description (size)
V 6 Diaphragm Nut (1/4” - 20)
15 Fluid Cap
(2) 93810-7
(2) 96460-1
(1) - - - - -
[P] 93810-7
[P] 96460-1
- - - - - - - -
- - - - - - - -
[P] 93810-3
[P] 96460-3
- - - - - - - -
- - - - - - - -
[K] 93810-3
[K] 96460-3
- - - - - - - -
- - - - - - - -
[K] 93810-2
[K] 96460-2 [GA] 96460-2 [GA]
- - - 92956-1 [SS] 92956-1 [SS]
[D] 93810-2
[D]
43 Ground Strap
57 Ground Kit Assembly
(1) - - - - -
- - - 66885-1
66885-1
(not shown)
60 Inlet Manifold (N.P.T.F.)
(BSP)
(1) 96468-1
(1) 96468-4
[P] 96468-7
[P] 96468-3
[K] 96468-9
[K] 96468-2 [GA] 96468-8 [GA]
[P] 96468-10 [P] 96468-6
[K] 96468-12 [K] 96468-5 [GA] 96468-11 [GA]
61 Outlet Manifold (N.P.T.F.) (1) 96469-1
[P] 96469-1
[P] 96469-4
- - - 94478-1
- - - 96559-1
[P] 96469-3
[P] 96469-6
[PPG] - - - - -
[PPG] - - - - -
[K] 96469-3
[K] 96469-6
- - - 94478-3
- - - 96559-3
[K] 96469-2 [GA] 96469-2 [GA]
[K] 96469-5 [GA] 96469-5 [GA]
(BSP)
63 Pipe Plug (N.P.T.F.)
(1) 96469-4
(1) - - - - -
(1) - - - - -
[K] - - - - -
[K] - - - - -
- - - 94478-2
- - - 96559-2
[D]
[D]
(BSP)
COMMON PARTS
Item Description (size)
Qty Part No.
[Mtl]
Item Description (size)
27 Bolt (1/4” - 20 x 1-1/8”)
29 Nut (1/4” - 20)
Qty Part No.
(12) 96471
(20) 93828
(2) 93264
[Mtl]
[SS]
[SS]
[A]
V 1 Connecting Rod
(1) 96532
(2) 96556
(8) 96471
[SS]
[GFN]
[SS]
5
Diaphragm Washer
26 Bolt (1/4” - 20 x 1-1/8”)
77 Logo Plate
DUAL INLET / DUAL OUTLET KITS 637442-X
Polypropylene
Kynar PVDF
Groundable Acetal
637442-1 (N.P.T.) 637442-4 (BSP) 637442-3 (N.P.T.) 637442-6 (BSP) 637442-2 (N.P.T.) 637442-5 (BSP)
Qty Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No. [Mtl] Part No. [Mtl]
Item Description (size)
17 Dual Outlet Manifold
18 Dual Inlet Manifold
(2) 96520-1
(2) 96519-1
[P] 96520-4
[P] 96519-4
[T] 96514
[P] 96520-3
[P] 96519-3
[T] 96514
[K] 96520-6
[K] 96519-6
[T] 96514
[K] 96520-2 [GA] 96520-5 [GA]
[K] 96519-2 [GA] 96519-5 [GA]
19 “O” Ring (3/32” x 1-1/8” o.d.) (4) 96514
[T] 96514
[T] 96514
[T]
V “Smart Parts” keep these items on hand in addition to the Service Kits for fast repair and reduction of down time.
Page 4 of 12
PE03P-X-X-A0S (en)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST / PE03P-X-X-A0S FLUID SECTION
COLOR CODE
3
2
1
4
DIAPHRAGM
COLOR
BALL
COLOR
Black (S)
Tan
White
MATERIAL
Hytrel
Santoprene
PTFE
Viton
17
Cream
Tan
White
5
6
Yellow (S)
Yellow (S)
(S) Dot
61
Torque Sequence
29 , U
43
Stainless steel seat installation
Radius (ball side)
Chamfer (fluid inlet side)
27 U
1 l
5
7
6 ,
22
21
19 l
26 U
29 , U
77
FOR THE
AIR MOTOR SECTION
SEE PAGES 6 & 7
15
26 U
22
63 `
21
60 (PE03P-XES-XXX-A0S,
PE03P-XLS-XXX-A0S,
PE03P-XRS-XXX-A0S)
19 l
29 , U
60 (PE03P-XDS-XXX-A0S,
PE03P-XKS-XXX-A0S,
PE03P-XPS-XXX-A0S)
View for PE03P-XXS-XXT-A0S (PTFE dia-
phragm) configuration only.
18
7 Fluid Side PTFE (white)
Figure 3
. TORQUE REQUIREMENTS ,
NOTE: DO NOT OVERTIGHTEN FASTENERS.
(6) Diaphragm nut 60 - 70 in. lbs (6.8 - 7.9 Nm).
(29) Nut 50 - 60 in. lbs (5.6 - 6.8 Nm), / alternately and evenly, then re-torque after initial run-in.
LUBRICATION / SEALANTS
` Apply pipe sealant to threads.
l Apply Lubriplate (94276) to all “O” rings, “U” cups and mating parts.
U Apply anti-seize compound to threads and boltand nutflange heads which contactpump
case when using stainless steel fasteners.
8 Air Side Santoprene (tan)
PE03P-X-X-A0S (en)
Page 5 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST / PE03P-X-X-A0S AIR MOTOR SECTION
(n) Indicates parts included in 637428 Air Section Repair Kit.
Item Description (size)
101 Center Body
Qty Part No.
(1) 96570
(1) 96488
(1) 96489
(2) 94874-1
(2) 96092
(12) 96093
(2) 59632-1
(1) 96542
(1) 96531
(1) 96214-1
(4) 93096
(4) Y6-47-T
(1) 96382
(2) Y187-47
[Mtl]
[PPG]
[D]
Item Description (size)
Qty Part No.
(1) 67382
[Mtl]
[D]
[U]
[U]
[D]
[B]
[B]
[B]
[B]
[B]
[SS]
n 167 Pilot Piston (includes 168 and 169)
168 “O” Ring (1/16” x 7/16” o.d.)
169 “U” Cup Packing (1/8” x 5/8” o.d.)
170 Spool Bushing
103R Cover (right side)
103L Cover (left side)
118 Actuator Pin
(2) 96459
[D]
(1) 96384
[SS]
[D]
(1) 96090
121 Washer
n 171 “O” Ring (1/16” x 13/16” o.d.)
n 173 “O” Ring (3/32” x 7/8” o.d.)
n 174 “O” Ring (3/32” x 11/32” o.d.)
n 200 Porting Gasket
(2) Y325-17
(2) Y325-115
(2) Y325-105
(1) 96364
123 Screw (#4 - 20 x 1/2”)
128 Plug (#10 - 32 x 5/32”)
129 Muffler Baffle
[SS]
[Ny]
[P]
130 Gasket
[SY]
[B]
n 232 “O” Ring (1/16” x 3/8” o.d.)
236 Nut (1/4” - 20)
(4) Y325-10
(4) Y12-4-S
n 132 Air Manifold Gasket
133 Washer (9/32” i.d. x 5/8” o.d.)
134 Flange Bolt (1/4” - 20 x 1-1/2”)
135 Porting Plate
[SS]
[SS]
[PPG]
[B]
n
Lubriplate FML-2 Grease
Lubriplate Grease, 10 Pack
(1) 94276
637308
n 144 “U” Cup Packing (1/8” x 3/4” o.d.)
MATERIAL CODE
AIR MOTOR SECTION SERVICE
[B]
[D]
= Nitrile
= Acetal
[PPG] = Glass Filled Polypropylene
[SS] = Stainless Steel
[SY] = Syn-Seal
S Air Motor Section Service is continued from Fluid Section repair.
[Ny] = Nylon
[P] = Polypropylene
[U]
= Polyurethane
PILOT VALVE DISASSEMBLY
DIAPHRAGM PUMP SERVICE
1. Remove(123)screws,releasing(103)covers,(121)washers,(118)
actuator pins and (167) pilot piston.
2. Remove (170) spool bushing and inspect inner bore of bushing for
damage.
3. Unthread (123) screws, releasing (129) muffler baffle.
4. Unthread (134) bolts and pull (135) porting plate and (132 and 200)
gaskets from (101) center body.
GENERAL SERVICE NOTES:
S Inspect and replace old parts with new parts as necessary. Look for
deep scratches on metallic surfaces, and nicks or cuts in “O” rings.
S Tools needed to complete disassembly and repair:
S 5/8” socket or wrench, 7/16” socket or wrench, 3/8” socket or
wrench, 5/16” Allen wrench, T-10 Torx screwdriver, torque
wrench (measuring inch pounds), “O” ring pick.
PILOT VALVE REASSEMBLY
FLUID SECTION DISASSEMBLY
1. Clean and lubricate parts not being replaced from service kit.
2. Assemble (171) “O” rings to (170) bushing and assemble bushing
into (101) center body.
3. Lubricateandassemble(167)pilotpistonassemblyinto(170)bush-
ing.
4. Assemble (173 and 174) “O” rings and (121) washers to (103) cov-
ers, then insert (118) actuator pins through assembly.
5. Assemble (144) “U” cups (note the lip direction) and (103) covers to
(101)centerbody,securingwith(123)screws.NOTE:Tighten(123)
screws to 4 - 6 in. lbs (0.45 - 0.68 Nm).
6. Assemble (132 and 200) gaskets and (135) porting plate to center
body, securingwith(134)bolts. NOTE:Tighten(134)boltsto15-20
in. lbs (1.7 - 2.3 Nm).
1. Remove (61) top manifold.
2. Remove (19) “O” rings, (21) seats and (22) balls.
3. Remove (60) bottom manifold.
4. Remove (19) “O” rings, (21) seats and (22) balls.
5. Remove (15) fluid caps.
6. Remove(6)diaphragmnut,(7)or(7/8)diaphragmsand(5)washer.
7. Remove (1) connecting rod from air motor.
8. Carefully remove remaining (6) diaphragm nut, (7) or (7 / 8) dia-
phragms and (5) washer from (1) connecting rod. Do not mar sur-
face of connecting rod.
FLUID SECTION REASSEMBLY
7. Assemble(130)gasketand(129)mufflerbaffleto(101)centerbody,
securing with (123) screws. NOTE: Tighten (123) screws to 4 - 6 in.
lbs (0.45 - 0.68 Nm).
S Reassemble in reverse order.
S Lubricate (1) connecting rod with Lubriplate or equivalent “O” ring
lubricant.
S Install (5) washers with i.d. chamfer toward diaphragm.
S When replacing PTFE diaphragms, install the 96533-A Santoprene
diaphragm behind the PTFE diaphragm.
Page 6 of 12
PE03P-X-X-A0S (en)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST / PE03P-X-X-A0S AIR MOTOR SECTION
. TORQUE REQUIREMENTS ,
NOTE: DO NOT OVERTIGHTEN FASTENERS.
(134) Torque to 15 - 20 in. lbs (1.7 - 2.3 Nm), wait 10 minutes, then re-torque
to 15 - 20 in. lbs (1.7 - 2.3 Nm).
144 l 118
169 l 168 l 171 l
(123) Torque to 4 - 6 in. lbs (0.45 - 0.68 Nm).
. 123
LUBRICATION / SEALANTS
l
Apply Lubriplate (94276) to all “O” rings, “U” cups and mating parts.
103L
232
236
130
129
l 173
l 174
121
167
170
123 ,
133
. 134
135
144 l
103R
123 ,
128
132 l 200 l
128
101
118 121 174 l 173 l
Figure 4
ACCESSORIES
67388 WALL MOUNT BRACKET ASSEMBLY
96507 Wall Mount Bracket
Y13-3-T Washer (3) (3/16”)
Y14-10-S Lock Washer (3) (#10)
Y154-52-S Cap Screw (3)
(#10 - 24 x 1/2”)
Figure 5
PE03P-X-X-A0S (en)
Page 7 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE HOOK-UP CONNECTIONS
TYPICAL BASIC REMOTE HOOK-UP
(#10 - 32 PORTS ON PUMP ARE PLUGGED)
NOTE: Pump charges and exhausts through remote valve.
Supply air.
Spring return - solenoid actuated 4-way valve.
Figure 6
TYPICAL REMOTE HOOK-UP WITH POSITIVE FEEDBACK SIGNAL
NOTE: Pump may not be short-stroked with this system.
Valve will not run when pump does not cycle.
Supply air.
Air pilot return - solenoid actuated 4-way valve.
‘ PLC / Controller signal.
’ Pneumatic feedback signal from pump.
‘
’
Figure 7
Page 8 of 12
PE03P-X-X-A0S (en)
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE HOOK-UP CONNECTIONS
TYPICAL REMOTE HOOK-UP WITH ENHANCED POSITIVE FEEDBACK SIGNAL CAPABILITY
Supply air.
Air pilot return - solenoid actuated 4-way valve.
‘ PLC / Controller signal.
’ Pneumatic feedback signal from pump.
“ Pneumatic echo can be used to interrupt the PLC
signal and set alarm.
‘
“
’
NOTE: Pump may not be short-stroked with this system.
Pneumatic-to-electric signal can send alarm to operating system.
Figure 8
PE03P-X-X-A0S (en)
Page 9 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
Product discharged from air exhaust.
S Check for diaphragm rupture.
S Check tightness of (6) diaphragm nut.
Low output volume.
S Check air supply.
S Check for plugged outlet hose.
S For the pump to prime itself, it must be mounted in the vertical posi-
tion so that the balls will check by gravity.
Air Bubbles in product discharge.
S Check connections of suction plumbing.
S Check “O” rings between intake manifold and fluid caps.
S Check tightness of (6) diaphragm nut.
S Check for pump cavitation - suction pipe should be sized at least as
large as the inlet thread diameter of the pump for proper flow if high
viscosity fluids are being pumped. Suction hose must be non-col-
lapsible type, capable of pulling a high vacuum.
S Checkalljointsonintakemanifoldsandsuctionconnections. These
must be airtight.
Pump blows air out main exhaust when stalled on either stroke.
S Check “U” cups on (111) spool in major valve.
S Check (141) valve plate and (140) insert for wear.
S Check (169) “U” cup on (167) pilot piston.
S Inspectthepumpforsolidobjectslodgedinthediaphragmchamber
or the seat area.
DIMENSIONAL DATA
Dimensions shown are for reference only, they are shown in inches and millimeters (mm).
Exhaust Port 1/2 - 14 N.P.T.F. - 1
5-5/32” (130.6 mm)
Air Inlet 1/4 - 18 P.T.F. SAE Short
4-13/32” (111.5 mm)
4-7/8” (123.9 mm)
“B”
9-1/4”
(234.7 mm)
3/4” (19.1 mm)
8-15/32”
4-7/32”
(214.7 mm)
(106.9 mm)
1-3/32”
1-1/4”
(27.8 mm)
(31.8 mm)
9/32” Slot
2-25/32”
3/8” (9.5 mm)
4” (101.6 mm)
(7.1 mm)
(70.6 mm)
4-3/4” (120.7 mm)
5-9/16” (141.3 mm)
“A”
7-29/32” (200.2 mm)
Pump Model
“A” Material Inlet
3/8 - 18 N.P.T.F. - 1
“B” Material Outlet
3/8 - 18 N.P.T.F. - 1
PE03P-AXS-XXX-A0S
PE03P-BXS-XXX-A0S Rp 3/8 (3/8 - 19 BSP, parallel) Rp 3/8 (3/8 - 19 BSP, parallel)
Figure 9
Page 10 of 12
PE03P-X-X-A0S (en)
Download from Www.Somanuals.com. All Manuals Search And Download.
PE03P-X-X-A0S (en)
Page 11 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
PN 97999-1208
Page 12 of 12
PE03P-X-X-A0S (en)
Download from Www.Somanuals.com. All Manuals Search And Download.
|