Instructions for use
WASHING MACHINE
Contents
GB
Installation, 2-3-4-5
Unpacking and levelling
GB
Connecting the electricity and water supplies
The first wash cycle
English, 1
Technical data
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and options, 9
Table of programmes and wash cycles
Wash options
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
PWE 8168
Special wash cycles
Precautions and advice, 11
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 12
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 13
Service and Guarantee, 14-15-16
Before calling for Assistance
Guarantee
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the drain hose
• the supply voltage is included within the values i
ndicated on the Technical details table
(see page 5);
GB
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from
the floor;
• the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
65 - 100 cm
Your appliance is now supplied with a 13 amp fused
plug it can be plugged into a 13 amp socket for
immediate use. Before using the appliance please
read the instructions below.
The drain hose may be
connected to an
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
under-sink trap. Before
connecting the drain
hose from the machine
ensure that any blanks
or removable ends
have been taken off
the spigot.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used,
and the fuse cover re-fitted. If the fuse cover is lost,
the plug must not be used until a replacement is
obtained.
Replacement fuse covers:
If it is place over the
edge of a basin or sink
be sure the free end of
the hose should not be
underwater.
If a replacement fuse cover is fitted, it must be of the
correct colour as indicated by the coloured marking
or the colour that is embossed in words on the base
of the plug. Replacements can be obtained directly
from your nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded plug
and you should wish to re-route the mains cable
through partitions, units etc., please ensure that
either:
! We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
the plug is replaced by a fused 13 ampere re-
wearable plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp cable
outlet, controlled by a switch, (in compliance with BS
5733) which is accessible without moving the
appliance.
Ensure that if the drain hose is pushed into a
standpipe, that the end does not go down more
than 15cms (6 inches). If the hose is pushed down
too far, this may cause the machine to self -syphon
ie. continuously empty as it is filling.
Disposing of the plug:
Ensure that before disposing of the plug itself, you
make the pins unusable so that it cannot be
accidentally inserted into a socket.
Electric connection
Before plugging the appliance into the mains
socket, make sure that:
Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
• the socket is earthed and in compliance with the
applicable law;
Green & Yellow Earth
Blue
Neutral
Live
• the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (see page 5);
Brown
3
Download from Www.Somanuals.com. All Manuals Search And Download.
As the colours of the wires in the lead may not
correspond with the coloured markings identifyng
the terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked E
Warning! The company denies all liability if and when
these norms are not respected.
GB
The first wash cycle
or
or coloured Green or Green & Yellow.
Connect Brown wire to terminal marked L or
coloured Red.
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.
Connect Blue wire to terminal marked N or coloured
Black.
If a 13 amp plug (BS 1363) is used it must be fitted
with a
13 amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt the electrical supply to your
machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE
NEUTRAL (N)
LIVE (L)
BROWN
GREEN & YELLOW
EARTH (E)
Disposing of the appliance:
When disposing of the appliance please remove the
plug by cutting the mains cable as close as possible
to the plug body and dispose of it as described
above.
GREEN &
YELLOW
13 ampere fuse
BROWN
CROSS-BAR
CORD GRIP
BLUE
! The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
! When the washing machine is installed, the mains
socket must be within easy reach.
! Do not use extensions or multiple sockets.
! The power supply cable must never be bent or
dangerously compressed.
! The power supply cable must only be replaced by
an authorised serviceman.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
Technical data
Model
PWE 8168
width 59.5 cm
height 85 cm
depth 62 cm
Dimensions
Capacity
from 1 to 8 kg
Electrical
please refer to the technical data
plate fixed to the machine
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 62 litres
Water connections
Spin speed
up to 1600 rotations per minute
Energy rated
programmes
according to
regulation
programme 1; temperature 60°C;
using a load of 8 kg.
EN 60456
This appliance conforms to the
following EC Directives:
- 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent modifications
- 2006/95/EC (Low Voltage)
- 2002/96/EC
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the washing
machine
Control panel
GB
OPTION
buttons and
indicator lights
DOOR
LOCKED
indicator light
ON/OFF
button
TEMPERATURE
button
DISPLAY
DELAY
TIMER
button
WASH
CYCLE
SELECTOR
KNOB
SPIN
button
Detergent dispenser drawer
START/PAUSE
button and indicator
light
Detergent dispenser drawer: used to dispense
detergents and washing additives ( see “Detergents
and laundry”).
DELAY TIMER
button: press to set a delayed
start for the selected wash cycle; the delay period
appears on the display.
ON/OFF
button: press this briefly to switch the
START/PAUSE
button and indicator light: when
machine on or off. The START/PAUSE indicator light
which flashes slowly in a blue colour shows that the
machine is switched on. To switch off the washing
machine during the wash cycle, press and hold the
button for approximately 3 seconds; if the button is
pressed briefly or accidentally the machine will not
switch off.
the blue indicator light flashes slowly, press the button
to start a wash cycle. Once the cycle has begun the
indicator light will remain lit in a fixed manner. To
pause the wash cycle, press the button again; the
indicator light will flash in an amber colour. If the
symbol is not illuminated, the door may be opened. To
start the wash cycle from the point at which it was
interrupted, press the button again.
If the machine is switched off during a wash cycle,
this wash cycle will be cancelled.
DOOR LOCKED
indicator light:
WASH CYCLE SELECTOR KNOB: used to set the
desired wash cycle (see “Table of programmes and
wash cycles”).
The lit symbol indicates that the door is locked. To
prevent any damage, wait until the symbol turns off
before opening the door.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened.
OPTION buttons and indicator lights: press to
select the available options. The indicator light
corresponding to the selected option will remain lit.
Standby mode
SPIN
button: press to reduce or completely
This washing machine, in compliance with new
energy saving regulations, is fitted with an automatic
standby system which is enabled after a few minutes
if no activity is detected. Press the ON-OFF button
briefly and wait for the machine to start up again.
exclude the spin cycle; the value appears on the
display.
TEMPERATURE
button: press to reduce or
completely exclude the temperature; the value
appears on the display.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Display
GB
B
A
C
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the
DELAYED START option has been set, the countdown to the start of the selected wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained
by the machine during the set wash cycle, or the values selected most recently, if these are compatible with the
set wash cycle.
The hour-glass flashes while the machine is processing data, depending on the wash cycle and Smart level
selected. After a maximum of 10 minutes, the “hour-glass” icon remains lit in a fixed manner and the final amount
of time remaining is displayed. The hour-glass icon will then switch off approximately 1 minute after the final
amount of time remaining has appeared.
The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running
wash cycle appear in section B:
Main wash
Rinse
Spin
Drain
The icons corresponding to “temperature”, “spin” and “delay timer” (working from the left) are displayed in section C.
The “temperature” bars
indicate the maximum temperature level which may be selected for the set cycle.
indicate the maximum spin level which may be selected for the set cycle.
The “spin” bars
The “delay” symbol
, when lit, indicates that the set “delayed start” value has appeared on the display.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Running a wash cycle
and only the second option will be activated; the
1. SWITCH THE MACHINE ON. Press the
button; the START/PAUSE indicator light will flash
slowly in a blue colour.
GB
indicator light for the option which has been
activated will be illuminated.
Note: if the SMART option has been selected,
none of the incompatible options may be activated.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
! The options may affect the recommended load
value and/or the duration of the cycle.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent
into the relevant compartments as described in
“Detergents and laundry”.
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will
turn blue, remaining lit in a fixed manner, and the
door will be locked (the DOOR LOCKED
symbol
will be lit). To change a wash cycle while it is in
progress, pause the washing machine using the
START/PAUSE button (the START/PAUSE indicator
light will flash slowly in an amber colour); then
select the desired cycle and press the START/
PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened.
Press the START/PAUSE button again to restart the
wash cycle from the point at which it was
interrupted.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH
CYCLE SELECTOR knob to select the desired
wash cycle. A temperature and spin speed is set for
each wash cycle; these values may be adjusted.
The duration of the cycle will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the
relevant buttons:
Modify the temperature and/or spin speed.
The machine automatically displays the maximum
temperature and spin speed values set for the
selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when
the DOOR LOCKED
symbol switches off the door
may be opened. Open the door, unload the laundry
and switch off the machine.
! If you wish to cancel a cycle which has already
begun, press and hold the button. The cycle will be
stopped and the machine will switch off.
reached. The spin speed may be progressively
reduced by pressing the
completely excluded (the “OFF” setting). If these
buttons are pressed again, the maximum values
are restored.
button, until it is
Load balancing system
Setting a delay timer.
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a
uniform manner, the drum rotates continuously at a
speed which is slightly greater than the washing
rotation speed. If, after several attempts, the load is
not balanced correctly, the machine spins at a
reduced spin speed. If the load is excessively
unbalanced, the washing machine performs the
distribution process instead of spinning. To encourage
improved load distribution and balance, we
recommend small and large garments are mixed in
the load.
To set a delayed start for the selected cycle, press
the corresponding button repeatedly until the
required delay period has been reached. When this
option has been activated, the
symbol lights up
on the display. To remove the delayed start setting,
press the button until the text “OFF” appears on
the display.
Modify the cycle settings.
• Press the button to enable the option; the
indicator light corresponding to the button will
switch on.
• Press the button again to disable the option; the
indicator light will switch off.
! If the selected option is not compatible with the
set wash cycle, the indicator light will flash and the
option will not be activated.
! If the selected option is not compatible with a
previously selected one, the indicator light
corresponding to the first function selected will flash
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash cycles and
options
Table of programmes and wash cycles
GB
Detergents
Max.
temp.
(°C)
Max.
speed
(rpm)
Max.
load
(kg)
Cycle
duration
Description of the wash cycle
Smart cycles
Main
wash
Fabric softener
1
1
Cotton
: extremely soiled whites.
90°
60°
1600
1600
8
8
•
•
•
•
•
•
Cotton (1)
: heavily soiled whites and
resistant colours.
Cotton (2): heavily soiled whites and
delicate colours.
White Cotton: heavily soiled whites
and resistant colours.
1
2
3
4
5
40°
60°
40°
30°
40°
1600
1600
1600
1600
800
8
8
•
•
•
•
•
•
•
•
Coloured Cotton (3)
: lightly soiled
8
whites and delicate colours.
Cotton
: lightly soiled whites and
8
delicate colours.
Synthetics: lightly soiled resistant
colours.
3,5
6
7
Jeans
Shirts
40°
40°
800
600
4
2
•
•
•
•
Mix-Cool 30’: to refresh lightly soiled
garments quickly (not suitable for
wool, silk and clothes which require
washing by hand).
Cold
water
8
800
3
•
•
Special cycles
9
Wool
: for wool, cashmere, etc.
40°
30°
600
0
2
2
•
•
•
•
Delicates: for garments in silk and
viscose, lingerie.
10
11
12
Duvet: for down-stuffed garments
30°
30°
1000
400
3
•
•
•
•
Outwear
-
2,5
Max.
2 pairs
13
Sport Shoes
30°
600
•
Partial cycles
Rinse
-
1600
-
8
•
-
-
Spin
Drain
-
-
1600
0
-
-
8
8
For all Test Institutes:
1) Test wash cycle in compliance with regulation EN 60456: select wash cycle 1 with a temperature of 60°C.
2) Long wash cycle for cottons: select wash cycle 1 with a temperature of 40.
3) Short wash cycle for cottons: select wash cycle 3 with a temperature of 40.
slow rotations of the drum, while the EASY IRON and
START/PAUSE indicator lights will flash (blue and orange
respectively). To end the cycle, press the START/PAUSE
button or the EASY IRON button. For wash cycles
number 10-12, the machine will end the cycle while the
laundry is soaking; the EASY IRON and START/PAUSE
indicator lights will flash. To drain the water so that the
laundry may be removed, press the START/PAUSE
button or the EASY IRON button.
Wash options
The
option optimises washing to suit the quantity of
laundry loaded into the machine, thereby reducing the overall
wash cycle duration while minimising water and energy
consumption. Press the
wash cycle desired:
button to select the type of
Intense: vigorous wash cycle for garments with a heavy soil
level.
! It cannot be used in conjunction with wash cycles 8,
9, 13,
Perform: standard wash cycle for garments with a normal soil level.
Fast: quick wash cycle for garments with a light soil level.
! This may only be used in conjunction with wash cycles 1, 2, 3,
4, 5 (all three levels) and 6, 7, 8 (Perform and Fast levels).
,
.
Cool Wash
The Eco Wash function saves energy by not heating the
water used to wash your laundry – an advantage both
to the environment and to your energy bill. Instead,
intensified wash action and water optimisation ensure
great wash results in the same average time of a
standard cycle.
Extra Rinse
By selecting this option, the efficiency of the rinse is increased
and optimal detergent removal is guaranteed. It is particularly
useful for sensitive skin.
! It cannot be used in conjunction with wash cycles 8,
,
.
For the best washing results we recommend the usage
of a liquid detergent.
! It cannot be used in conjunction with wash cycles 7,
Easy iron
By selecting this function, the wash and spin cycles will be
modified in order to reduce the formation of creases. At
the end of the cycle the washing machine will perform
8, 9, 10, 11, 13,
,
,
.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergents and laundry
Detergent dispenser drawer
Wool: wash cycle 9 can be used to wash all woollen
garments in the machine, even those carrying the “hand
wash only” label. To achieve the best results, use a
GB
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in fact
cause build up on the inside of your appliance and
contribute to environmental pollution.
special detergent and do not exceed the maximum load of
2 kg.
Delicates: use special wash cycle 10 to wash all silk
garments. We recommend the use of special detergent
which has been designed to wash delicate clothes.
Curtains: we recommend you fold the curtains and place
them in a pillow case or mesh bag. Use wash cycle 10.
Duvet: to wash double or single duvets (the weight of
which should not exceed 3 kg), cushions or clothes
padded with goose down such as puffa jackets, use the
special wash cycle number 11 “Duvet”. We recommend
that duvets are placed in the drum with their edges
folded inwards (see figure) and that no more than ¾ of
the total volume of the drum is used.
! Do not use hand washing detergents; they create too
much foam.
Open the detergent
dispenser drawer and pour in
the detergent or washing
3
additive, as follows.
2
1
Compartment 1:
Washing detergent
(powder or liquid)
To achieve the best results, we recommend that a liquid
detergent is used and placed inside the detergent
dispenser drawer.
Liquid detergent should only
be poured in immediately
prior to the start of the wash cycle.
Compartment 2: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 3: we recommend this
compartment is used for liquid detergent.
Preparing the laundry
• Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Empty all garment pockets and check the buttons.
• Do not exceed the listed values, which refer to the
weight of the laundry when dry:
Outwear (wash cycle 12): is studied for washing
water-repellent fabrics and winter jackets (e.g. Gore-
Tex, polyester, nylon); for best results, use a liquid
detergent and dosage suitable for a half-load; pre-
treat necks, cuffs and stains if necessary; do not use
softeners or detergents containing softeners. Stuffed
duvets cannot be washed with this programme.
Sport Shoes (wash cycle 13): is for washing sports
shoes; for best results, do not wash more than 2 pairs
simultaneously.
Durable fabrics: max. 8 kg
Synthetic fabrics: max. 3.5 kg
Delicate fabrics: max. 2 kg
Wool: max. 2 kg
Silk: max. 2 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special wash cycles
Jeans: turn the garments inside out before washing and
use liquid detergent. Use wash cycle 6.
Shirts: use special wash cycle 7 to wash shirts in various
fabrics and colours. It guarantees maximum care is taken
of the garments and minimises the formation of creases.
Mix-Cool 30’: this wash cycle was designed to wash
lightly soiled garments quickly: it lasts just 30 minutes and
therefore saves both energy and time. By selecting wash
cycle 8, it is possible to wash different fabrics (except for
wool and silk items) using a cold cycle, up to a maximum
load of 3 kg.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions and tips
! This washing machine was designed and constructed
in accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
Opening the porthole door manually
GB
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove
the laundry, proceed as follows:
General safety
1. Remove the plug from
the electrical socket..
2. Make sure the water
level inside the machine is
lower than the door
• This appliance was designed for domestic use only.
• The washing machine must only be used by adults, in
accordance with the instructions provided in this manual.
• Do not touch the machine when barefoot or with wet
or damp hands or feet.
opening; if it is not, remove
excess water using the
drain hose, collecting it in a
bucket as indicated in the
figure.
• Do not pull on the power supply cable when
unplugging the appliance from the electricity socket.
Hold the plug and pull.
• Do not open the detergent dispenser drawer while the
machine is in operation.
3. Remove the cover panel on the lower front part of
the washing machine (see overleaf).
• Do not touch the drained water as it may reach
extremely high temperatures.
• Never force the porthole door. This could damage the
safety lock mechanism designed to prevent accidental
opening.
• If the appliance breaks down, do not under any
circumstances access the internal mechanisms in an
attempt to repair it yourself.
• Always keep children well away from the appliance
while it is operating.
• The door can become quite hot during the wash cycle.
• If the appliance has to be moved, work in a group of
two or three people and handle it with the utmost
care. Never try to do this alone, because the
appliance is very heavy.
4. Pull outwards using the tab as indicated in the
figure, until the plastic tie-rod is freed from its stop
position; pull downwards and open the door at the
same time.
• Before loading laundry into the washing machine,
make sure the drum is empty.
5. Reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Disposal
• Disposing of the packaging materials:
observe local regulations so that the packaging may
be re-used.
• The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states
that household appliances should not be disposed of
using the normal solid urban waste cycle. Exhausted
appliances should be collected separately in order to
optimise the cost of re-using and recycling the
materials inside the machine, while preventing
potential damage to the atmosphere and to public
health. The crossed-out dustbin is marked on all
products to remind the owner of their obligations
regarding separated waste collection.
For more information relating to the correct disposal of
household appliances, owners should contact their
local authorities or appliance dealer.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and maintenance
Cutting off the water and electricity
supplies
2. Unscrew the lid by
rotating it anti-clockwise
(see figure): a little water
may trickle out. This is
perfectly normal.
GB
• Turn off the water tap after every wash cycle. This
will limit wear on the hydraulic system inside the
washing machine and help to prevent leaks.
• Unplug the washing machine when cleaning it and
during all maintenance work.
Cleaning the washing machine
3. Clean the inside thoroughly.
4. Screw the lid back on.
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth soaked in
lukewarm soapy water. Do not use solvents or
abrasives.
5. Reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Cleaning the detergent dispenser
drawer
Checking the water inlet hose
To remove the drawer, press
Check the inlet hose at least once a year. If there are
any cracks, it should be replaced immediately: during
the wash cycles, water pressure is very strong and a
cracked hose could easily split open.
1
lever (1) and pull the drawer
outwards (2) (see figure).
Wash it under running
water; this procedure should
be repeated frequently.
! Never use second-hand hoses.
2
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump which does not require any maintenance.
Sometimes, small items (such as coins or buttons) may
fall into the protective pre-chamber at the base of the
pump.
! Make sure the wash cycle has finished and unplug
the appliance.
To access the pre-chamber:
1. Take off the cover panel
on the front of the
machine by first pressing it
1
in the centre and then
pushing downwards on
both sides until you can
2
3
remove it (see figures).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “
Service”), make sure that the problem cannot be not solved easily using the following list.
GB
Problem:
Possible causes / Solutions:
The washing machine does not • The appliance is not plugged into the socket fully, or not enough to make
switch on.
contact.
• There is no power in the house.
The wash cycle does not start. • The washing machine door is not closed properly.
• The ON/OFF button has not been pressed.
• The START/PAUSE button has not been pressed.
• The water tap has not been opened.
• A delayed start has been set.
The washing machine does not • The water inlet hose is not connected to the tap.
fill with water (the text “H2O”
flashes on the display).
• The hose is bent.
• The water tap has not been opened.
• There is no water supply in the house.
• The pressure is too low.
• The START/PAUSE button has not been pressed.
The washing machine
continuously takes in and
drains water.
• The drain hose is not fitted at a height between 65 and 100 cm from the floor
(see “Installation”).
• The free end of the hose is under water (see “Installation”).
• The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Technical Assistance Service. If the dwelling is
on one of the upper floors of a building, there may be problems relating to water
drainage, causing the washing machine to fill with water and drain continuously.
Special anti-draining valves are available in shops and help to prevent this
inconvenience.
The washing machine does not • The wash cycle does not include draining: some cycles require the draining
drain or spin.
process to be enabled manually.
• The EASY IRON option is enabled: To complete the wash cycle, press the
START/PAUSE button (see “Wash cycles and options”).
• The drain hose is bent (see “Installation”).
• The drainage duct is clogged.
The washing machine vibrates • The drum was not unlocked correctly during installation (see “Installation”).
a lot during the spin cycle.
• The washing machine is not level (see “Installation”).
• The washing machine is trapped between cabinets and walls (see
“Installation”).
The washing machine leaks.
• The water inlet hose is not screwed on properly (see “Installation”).
• The detergent dispenser drawer is blocked (for cleaning instructions, see “Care
and maintenance”).
• The drain hose is not fixed properly (see “Installation”).
The “option” and START/PAUSE
indicator lights flash rapidly and
an error code appears on the
display (e.g.: F-01, F-..).
• Switch off the machine and unplug it, wait for approximately 1 minute and
then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
There is too much foam.
• The detergent is not suitable for machine washing (it should display the text
“for washing machines” or “hand and machine wash”, or the like).
• Too much detergent was used.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Before contacting the Technical Assistance Service:
GB
• Check whether you can solve the problem alone (see “Troubleshooting”).
• Restart the wash cycle to check whether the problem has been solved.
• If this is not the case, contact an authorised Technical Assistance Centre.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• the type of problem;
• the appliance model (Mod.);
• the serial number (S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found
on the front of the appliance by opening the door.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
12 Months Parts and Labour Guarantee
GB
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for
twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any
person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation.
Replacement of any consumable item or accessory . These include but are not limited to:
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR
NON-DOMESTIC PREMISES.
Extended Guarantees
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills
for the life of your policy. To find the ideal plan for you please call our advice line on
08709 088 088 (ROI 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you experience any
technical difficulties within the first 90 days of ownership. Simply call our Indesit Service Hotline on 08709 066 066
(ROI 0818 313 413) for telephone assistance, or, where necessary, to arrange for an engineer to call.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
195075239.00
01/2009
-
Xerox Fabriano
After Sales Service
GB
No one is better placed to care for your Indesit appliance during the course of its working life than us - the manufacturer.
Essential Contact Information
Indesit Service
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100 fully qualified
engineers on call to ensure you receive fast, reliable, local service.
UK: 08709 066 066
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean
your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08709 077 077
Republic of Ireland: 0818 313 413
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17
Recycling & Disposal Information
As part of Indesit's continued commitment to helping the environment, Indesit reserves the right to use quality, recycled
components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the door, plug
and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that the appliance can
no longer be plugged into a mains socket, and the door cannot be locked shut.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|