Indesit Washer IWC 71450 User Manual

Instructions for use  
WASHING MACHINE  
Contents  
GB  
Installation, 2-3-4-5  
Unpacking and levelling  
Connecting the electricity and water supplies  
The first wash cycle  
GB  
English,1  
Technical data  
Description of the washing machine  
and starting a wash cycle, 6-7  
Control panel  
Indicator lights  
Starting a wash cycle  
Wash cycles, 8  
Table of wash cycles  
Personalisation, 9  
Setting the temperature  
Setting the spin speed  
Functions  
IWC 71450  
Detergents and laundry, 10  
Detergent dispenser drawer  
Preparing the laundry  
Garments requiring special care  
Load balancing system  
Precautions and tips, 11  
General safety  
Disposal  
Care and maintenance, 12  
Cutting off the water or electricity supply  
Cleaning the washing machine  
Cleaning the detergent dispenser drawer  
Caring for the door and drum of your appliance  
Cleaning the pump  
Checking the water inlet hose  
Troubleshooting, 13-14  
Assistance, 15-16  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the drain hose  
• the supply voltage is included within the values indica  
GB  
ted on the Technical details table (see page 5);  
Connect the drain hose,  
without bending it, to a  
draining duct or a wall  
drain situated between  
65 and 100 cm from the  
floor;  
• the socket is compatible with the washing machines  
plug. If this is not the case, replace the socket or the  
plug.  
65 - 100 cm  
Your appliance is now supplied with a 13 amp fused plug  
it can be plugged into a 13 amp socket for immediate use.  
Before using the appliance please read the instructions  
below.  
WARNING - THIS APPLIANCE MUST BE EARTHED.  
THE FOLLOWING OPERATIONS SHOULD BE CARRIED  
OUT BY A QUALIFIED ELECTRICIAN.  
The drain hose may be  
connected to an under-  
sink trap. Before connec-  
ting the drain hose from  
the machine ensure that  
any blanks or removable  
ends have been taken off  
the spigot.  
Replacing the fuse:  
When replacing a faulty fuse, a 13 amp ASTA approved  
fuse to BS 1362 should always be used, and the fuse  
cover re-fitted. If the fuse cover is lost, the plug must not  
be used until a replacement is obtained.  
Where it connects to  
the waste water pipe  
cut end off spigot or  
remove the blanking cap  
Replacement fuse covers:  
If a replacement fuse cover is fitted, it must be of the  
correct colour as indicated by the coloured marking or the  
colour that is embossed in words on the base of the plug.  
Replacements can be obtained directly from your nearest  
Service Depot.  
If it is placed over the  
edge of a basin or sink  
be sure the free end of  
the hose should not be  
underwater.  
Removing the plug:  
If your appliance has a non-rewireable moulded plug and  
you should wish to re-route the mains cable through parti-  
tions, units etc., please ensure that either:  
the plug is replaced by a fused 13 ampere re-wearable  
plug bearing the BSI mark of approval.  
or:  
! We advise against the use of hose extensions; in case  
of absolute need, the extension must have the same  
diameter as the original hose and must not exceed 150  
cm in length.  
the mains cable is wired directly into a 13 amp cable out-  
let, controlled by a switch, (in compliance with BS 5733)  
which is accessible without moving the appliance.  
Ensure that if the drain hose is pushed into a standpipe,  
that the end does not go down more than 15cms (6 in-  
ches). If the hose is pushed down too far, this may cause  
the machine to self -syphon ie. continuously empty as it  
is filling.  
Disposing of the plug:  
Ensure that before disposing of the plug itself, you make  
the pins unusable so that it cannot be accidentally inserted  
into a socket.  
Instructions for connecting cable to an alternative plug:  
Important: the wires in the mains lead are coloured in  
accordance with the following code:  
Electric connection  
Before plugging the appliance into the mains socket,  
make sure that:  
Green & Yellow Earth  
Blue  
Brown  
Neutral  
Live  
• the socket is earthed and in compliance with the ap-  
plicable law;  
• the socket is able to sustain the appliances maximum  
power load indicated in the Technical details table (see  
page 5);  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
As the colours of the wires in the lead may not correspond  
with the coloured markings identifying the terminals in your  
plug, proceed as follows:  
Connect Green & Yellow wire to terminal marked E or  
or coloured Green or Green & Yellow.  
The first wash cycle  
GB  
Once the appliance has been installed, and before you use  
it for the first time, run a wash cycle with detergent and no  
laundry, setting the 90°C programme without a pre-wash  
cycle.  
Connect Brown wire to terminal marked L or coloured  
Red.  
Connect Blue wire to terminal marked N or coloured Black.  
If a 13 amp plug (BS 1363) is used it must be fitted with a  
13 amp fuse, either in the plug or adaptor or at the distri-  
bution board.  
If you are in any doubt about the electrical supply to your  
machine, consult a qualified electrician before use.  
How to connect an alternative plug:  
The wires in this mains lead are coloured in accordance  
with the following code:  
BLUE  
BROWN  
NEUTRAL (N)  
LIVE (L)  
GREEN & YELLOW  
EARTH (E)  
GREEN &  
YELLOW  
13 ampere fuse  
BROWN  
BLUE  
CROSS-BAR  
CORD GRIP  
Disposing of the appliance:  
When disposing of the appliance please remove the plug  
by cutting the mains cable as close as possible to the plug  
body and dispose of it as described above.  
! The washing machine should not be installed in an  
outdoor environment, not even when the area is sheltered,  
because it may be very dangerous to leave it exposed to  
rain and thunderstorms.  
! When the washing machine is installed, the mains socket  
must be within easy reach.  
! Do not use extensions or multiple sockets.  
! The power supply cable must never be bent or dange-  
rously compressed.  
! The power supply cable must only be replaced by an  
authorised serviceman.  
Warning! The company denies all liability if and when these  
norms are not respected.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
GB  
Technical data  
Model  
IWC 71450  
width 59.5 cm  
height 85 cm  
depth 53,5 cm  
Dimensions  
Capacity  
from 1 to 7 kg  
Electrical  
please refer to the technical data plate  
fixed to the machine  
connections  
maximum pressure 1 MPa (10 bar)  
minimum pressure 0.05 MPa (0.5 bar)  
drum capacity 52 litres  
Water connection  
Spin speed  
up to 1400 rotations per minute  
Energy rated pro-  
grammes accor-  
ding to regulation  
EN 60456  
programme 1; temperature 60°C;  
using a load of 7 kg.  
This appliance conforms to the following  
EC Directives:  
- 2004/108/EC (Electromagnetic  
Compatibility)  
- 2002/96/EC  
- 2006/95/EC Low Voltage)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Description of the washing  
machine and starting a wash cycle  
Control panel  
GB  
WASH CYCLE PROGRESS/  
DELAY TIMER indicator lights  
FUNCTION  
START/PAUSE  
ON/OFF button  
buttons with  
button with  
indicator lights  
indicator light  
TEMPERATURE  
DOOR LOCKED  
knob  
indicator light  
Detergent dispenser drawer  
WASH CYCLE  
SPIN SPEED  
knob  
knob  
Detergent dispenser drawer: used to dispense  
detergents and washing additives (see “Detergents and  
laundry”).  
DOOR LOCKED indicator light: indicates whether the  
door may be opened or not (see next page).  
START/PAUSE button with indicator light: starts or tem-  
porarily interrupts the wash cycles.  
ON/OFF button: switches the washing machine on and off.  
N.B. To pause the wash cycle in progress, press this  
button; the corresponding indicator light will flash orange,  
while the indicator light for the current wash cycle phase  
will remain lit in a fixed manner. If the DOOR LOCKED  
indicator light is switched off, the door may be opened.  
To start the wash cycle from the point at which it was inter-  
rupted, press this button again.  
WASH CYCLE knob: programmes the wash cycles. Du-  
ring the wash cycle, the knob does not move.  
FUNCTION buttons with indicator light: used to select the  
available functions. The indicator light corresponding to the  
selected function will remain lit.  
TEMPERATURE knob: sets the temperature or the cold  
wash cycle (see “Personalisation”).  
Standby mode  
This washing machine, in compliance with new energy sa-  
ving regulations, is fitted with an automatic standby system  
which is enabled after about 30 minutes if no activity is  
detected. Press the ON-OFF button briefly and wait for the  
machine to start up again.  
SPIN SPEED knob: sets the spin speed or exclude the  
spin cycle completely (see “Personalisation”).  
WASH CYCLE PROGRESS/DELAY TIMER indicator  
lights: used to monitor the progress of the wash cycle.  
The illuminated indicator light shows which phase is in  
progress.  
If the Delay Timer function has been set, the time remai-  
ning until the wash cycle starts will be indicated (see next  
page).  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wash cycle phase indicator lights  
Indicator lights  
GB  
Once the desired wash cycle has been selected and has be-  
gun, the indicator lights switch on one by one to indicate which  
phase of the cycle is currently in progress.  
The indicator lights provide important information.  
This is what they can tell you:  
Wash  
Rinse  
Delayed start  
If the DELAY TIMER function has been activated (see “Per-  
sonalisation”), after the wash cycle has been started the  
indicator light corresponding to the selected delay period  
will begin to flash:  
Spin  
Drain  
End of wash cycle  
Function buttons and corresponding indicator lights  
When a function is selected, the corresponding indicator  
light will illuminate.  
If the selected function is not compatible with the program-  
med wash cycle, the corresponding indicator light will flash  
and the function will not be activated.  
If the selected function is not compatible with another  
function which has been selected previously, the indicator  
light corresponding to the first function selected will  
flash and only the second function will be activated; the  
indicator light corresponding to the enabled option will  
remain lit.  
As time passes, the remaining delay will be displayed and  
the corresponding indicator light will flash:  
Door locked indicator light  
When the indicator light is on, the porthole door is locked  
to prevent it from being opened; make sure the indicator  
light is off before opening the door (wait approximately 3  
minutes). To open the door during a running wash cycle,  
press the START/PAUSE button; the door may be opened  
once the DOOR LOCKED indicator light turns off.  
The set programme will start once the selected time delay  
has expired.  
Starting a wash cycle  
1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then  
they will switch off and the START/PAUSE indicator light will pulse.  
2. Load the laundry and close the door.  
3. Set the WASH CYCLE knob to the desired programme.  
4. Set the washing temperature (see “Personalisation”).  
5. Set the spin speed (see “Personalisation”).  
6. Measure out the detergent and washing additives (see “Detergents and laundry”).  
7. Select the desired functions.  
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed man-  
ner, in green. To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.  
9. At the end of the wash cycle the  
indicator light will switch on. The door can be opened once the DOOR LOCK indi-  
cator light turns off. Take out your laundry and leave the appliance door ajar to make sure the drum dries completely. Switch  
the washing machine off by pressing the ON/OFF button.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wash cycles  
Table of wash cycles  
GB  
Cycle dura-  
tion  
Detergents  
Max. load (kg)  
Max. Max.  
temp. speed  
Description of the wash cycle  
Fabric  
Eco Nor- Eco  
Time mal Time  
(°C)  
(rpm)  
Wash  
Normal  
softener  
Daily  
1
1
1
2
3
4
5
White Cotton: extremely soiled whites.  
White Cotton (1): heavily soiled whites and resistant colours.  
White Cotton (2): lightly soiled whites and delicate colours.  
Cotton: heavily soiled whites and resistant colours.  
Coloured Cotton (3): lightly soiled and delicate colours.  
Cotton: lightly soiled whites and resistant colours.  
Synthetics: heavily soiled resistant colours.  
Special  
90°  
60°  
40°  
60°  
40°  
30°  
50°  
1400  
1400  
1400  
1400  
1400  
1400  
800  
7
7
7
7
7
7
3
-
-
-
3.5  
3.5  
3.5  
2
165  
170  
165  
-
-
-
130 105  
90  
85  
80  
80  
75  
70  
6
7
8
Wool: for wool, cashmere, etc.  
Silk/Curtains: for garments in silk and viscose, lingerie.  
Jeans  
40°  
30°  
40°  
600  
0
800  
1.5  
1
3
-
-
-
55  
55  
70  
-
-
-
Express 15': to refresh lightly soiled garments quickly (not suitable for wool,  
silk and clothes which require washing by hand).  
9
30°  
60°  
800  
1,5  
3.5  
-
-
15  
60  
-
-
10 Flash Cotton  
Sport  
1400  
11 Sport Intensive  
12 Sport Light  
30°  
30°  
600  
600  
3
3
-
-
80  
70  
-
-
Max. 2  
pairs  
13 Special Shoes  
30°  
600  
-
50  
-
Partial wash cycles  
Rinse  
Spin  
Drain  
-
-
-
1400  
1400  
0
-
-
-
-
-
7
7
7
-
-
-
35  
15  
2
-
-
-
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary  
according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options  
selected.  
For all Test Institutes:  
1) Test wash cycle in compliance with regulation EN 60456: set wash cycle 1 with a temperature of 60°C.  
2) Long wash cycle for cottons: set wash cycle 1 with a temperature of 40°C.  
3) Short wash cycle for cottons: set wash cycle 3 with a temperature of 40°C.  
Specials wash cycles  
Express 15’ (wash cycle 9) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and  
therefore saves both energy and time. By selecting this wash cycle (9 at 30°C), it is possible to wash different fabrics together  
(except for wool and silk items), with a maximum load of 1.5 kg.  
Sport Intensive (wash cycle 11) is for washing heavily soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results,  
we recommend not exceeding the maximum load indicated in the Table of wash cycles”  
.
Sport Light (wash cycle 12) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results, we  
recommend not exceeding the maximum load indicated in the Table of wash cycles”. We recommend using a liquid deter-  
gent and dosage suitable for a half-load.  
Special Shoes (wash cycle 13) is for washing sports shoes; for best results, do not wash more than 2 pairs simultaneously.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Personalisation  
Setting the temperature  
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).  
GB  
The temperature may be lowered, or even set to a cold wash  
.
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value  
set for each wash cycle.  
Setting the spin speed  
Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.  
The maximum spin speeds available for each wash cycle are as follows:  
Wash cycles  
Cottons  
Synthetics  
Wool  
Maximum spin speed  
1400 rpm  
800 rpm  
600 rpm  
Silk  
drain only  
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol  
.
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed  
set for each wash cycle.  
Functions  
The various wash functions available with this washing machine will help to achieve the desired results, every time.  
To activate the functions:  
1. Press the button corresponding to the desired function;  
2. the function is enabled when the corresponding indicator light is illuminated.  
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the  
selected wash cycle.  
Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly soiled  
cotton and synthetic fabrics (refer to the Table of wash cycles”). “  
” enables you to wash in less time thereby saving  
water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity.  
! This function may not be used in conjunction with wash cycles 1, 6, 7, 8, 9, 10, 11, 12, 13,  
,
,
.
Intensive Wash  
Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle duration, this  
function offers a high-performance wash.  
! This function may not be used in conjunction with wash cycles 6, 7, 8, 9, 10, 11, 12, 13,  
,
,
.
Extra Rinse  
By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly  
useful for sensitive skin.  
! This function may not be used in conjunction with wash cycles 9,  
,
.
Delay Timer  
This timer delays the start time of the wash cycle by up to 12 hours.  
Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time the button  
is pressed, the function will be disabled.  
N.B. Once the START/PAUSE button has been pressed, the delay time can only be modified by decreasing it until launching  
the set programme.  
! This option is enabled with all programmes.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Detergents and laundry  
Silk: use special wash cycle 7 to wash all silk garments.  
We recommend the use of special detergent which has  
been designed to wash delicate clothes.  
Curtains: fold curtains and place them in a pillow case or  
mesh bag. Use wash cycle 7.  
Jeans: Turn garments inside-out before washing and use  
a liquid detergent. Use programme 8.  
Detergent dispenser drawer  
GB  
Good washing results also depend on the correct dose of  
detergent: adding too much detergent will not necessa-  
rily result in a more efficient wash, and may in fact cause  
build up on the inside of your appliance and contribute to  
environmental pollution.  
! Do not use hand washing detergents because these  
create too much foam.  
Open the detergent di-  
spenser drawer and pour  
in the detergent or washing  
additive, as follows.  
Load balancing system  
Before every spin cycle, to avoid excessive vibrations and  
to distribute the load in a uniform manner, the drum rotates  
continuously at a speed which is slightly greater than the  
washing rotation speed. If, after several attempts, the load  
is not balanced correctly, the machine spins at a reduced  
spin speed. If the load is excessively unbalanced, the  
washing machine performs the distribution process instead  
of spinning. To encourage improved load distribution and  
balance, we recommend small and large garments are  
mixed in the load.  
3
2
1
!Do not pour detergent into the compartment 1.  
Detergent should only be poured into the compartment 2.  
compartment 2: Detergent for the wash cycle  
(powder or liquid)  
Liquid detergent should only be poured in immediately  
prior to the start of the wash cycle.  
compartment 3: Additives (fabric softeners, etc.)  
The fabric softener should not overflow the grid.  
Preparing the laundry  
• Divide the laundry according to:  
- the type of fabric/the symbol on the label  
- the colours: separate coloured garments from whites.  
• Empty all garment pockets and check the buttons.  
• Do not exceed the listed values, which refer to the weight  
of the laundry when dry:  
Durable fabrics: max. 7 kg  
Synthetic fabrics: max. 3 kg  
Delicate fabrics: max. 2 kg  
Wool: max. 1.5 kg  
Silk: max. 1 kg  
How much does your laundry weigh?  
1 sheet 400-500 g  
1 pillow case 150-200 g  
1 tablecloth 400-500 g  
1 bathrobe 900-1200 g  
1 towel 150-250 g  
Garments requiring special care  
Wool: all wool garments can be washed using programme 6,  
even those carrying the “hand-wash only”  
label.  
For best results, use special detergents and do not exceed  
1,5 kg of laundry.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Precautions and tips  
! This washing machine was designed and constructed in  
accordance with international safety regulations. The fol-  
lowing information is provided for safety reasons and must  
therefore be read carefully.  
Consumers should contact their local authority or  
retailer for information concerning the correct  
disposal of their old appliance.  
GB  
General safety  
• This appliance is not intended for use by persons (inclu-  
ding children) with reduced physical, sensory or mental  
capabilities, or lack of experience and knowledge, unless  
they have been given supervision or instruction concer-  
ning use of the appliance by a person responsible for  
their safety. Children should be supervised to ensure that  
they do not play with the appliance.  
• This appliance was designed for domestic use only.  
• Do not touch the machine when barefoot or with wet or  
damp hands or feet.  
• Do not pull on the power supply cable when unplugging  
the appliance from the electricity socket. Hold the plug  
and pull.  
• Do not open the detergent dispenser drawer while the  
machine is in operation.  
• Do not touch the drained water as it may reach extreme-  
ly high temperatures.  
• Never force the porthole door. This could damage the  
safety lock mechanism designed to prevent accidental  
opening.  
• If the appliance breaks down, do not under any circum-  
stances access the internal mechanisms in an attempt  
to repair it yourself.  
• Always keep children well away from the appliance while  
it is operating.  
• The door can become quite hot during the wash cycle.  
• If the appliance has to be moved, work in a group of two  
or three people and handle it with the utmost care. Never  
try to do this alone, because the appliance is very heavy.  
• Before loading laundry into the washing machine, make  
sure the drum is empty.  
Disposal  
• Disposing of the packaging materials: observe local  
regulations so that the packaging may be re-used.  
• The European Directive 2002/96/EC on Waste  
Electrical and Electronic Equipment, requires that  
old household electrical appliances must not be  
disposed of in the normal unsorted municipal waste  
stream. Old appliances must be collected separately  
in order to optimise the recovery and recycling of the  
materials they contain and reduce the impact on human  
health and the environment. The crossed out “wheeled  
bin” symbol on the product reminds you of your obliga-  
tion, that when you dispose of the appliance it must be  
separately collected.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care and maintenance  
2. unscrew the lid by rota-  
ting it anti-clockwise (see  
figure): a little water may  
trickle out. This is perfectly  
normal;  
Cutting off the water and electricity  
supplies  
GB  
Turn off the water tap after every wash cycle. This will  
limit wear on the hydraulic system inside the washing  
machine and help to prevent leaks.  
• Unplug the washing machine when cleaning it and du-  
ring all maintenance work.  
Cleaning the washing machine  
3. clean the inside thoroughly;  
4. screw the lid back on;  
5. reposition the panel, making sure the hooks are securely  
in place before you push it onto the appliance.  
The outer parts and rubber components of the appliance  
can be cleaned using a soft cloth soaked in lukewarm  
soapy water. Do not use solvents or abrasives.  
Cleaning the detergent dispenser drawer  
Checking the water inlet hose  
Remove the dispenser by  
raising it and pulling it out  
(see figure).  
Wash it under running wa-  
ter; this operation should be  
repeated frequently.  
Check the inlet hose at least once a year. If there are any  
cracks, it should be replaced immediately: during the wash  
cycles, water pressure is very strong and a cracked hose  
could easily split open.  
! Never use second-hand hoses.  
Caring for the door and drum of your  
appliance  
• Always leave the porthole door ajar in order to prevent  
unpleasant odours from forming.  
Cleaning the pump  
The washing machine is fitted with a self-cleaning pump  
which does not require any maintenance. Sometimes, small  
items (such as coins or buttons) may fall into the pre-cham-  
ber which protects the pump, situated in its bottom part.  
! Make sure the wash cycle has finished and unplug the  
appliance.  
To access the pre-chamber:  
1. using a screwdriver,  
remove the cover panel  
on the lower front part of  
the washing machine (see  
figure);  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure  
that the problem cannot be not solved easily using the following list.  
GB  
Problem:  
Possible causes / Solutions:  
The machine does not switch on.  
• The appliance is not plugged into the socket fully, or not enough to make contact.  
• There is no power to the socket, or the fuse has blown in the mains plug.  
The wash cycle does not start.  
• The door is not closed properly.  
• The ON/OFF button has not been pressed.  
• The START/PAUSE button has not been pressed.  
• The water tap has not been turned on to allow water to flow into the machine.  
• A delayed start has been set.  
The machine does not fill with wa-  
• The water inlet hose is kinked.  
ter or the indicator light for the first • The water inlet hose is not connected to the water supply.  
wash cycle stage flashes rapidly.  
• The water pressure is too low.  
• The water tap has not been turned on to allow water to flow into the machine.  
• There is no water supply to the house.  
• The inlet valve filter is blocked.  
• The START/PAUSE button has not been pressed.  
The machine continuously fills with • The top of the drain hose is too low - It must be fitted at a height between 65  
water and continually drains away  
or Water left in the drum  
or Stuck on wash.  
and 100 cm from the floor (see “Installation”).  
• The drain hose is connected incorrectly to the sink trap allowing water to run  
into the machine, the drain hose must be positioned higher than the bottom of  
the sink to prevent water flowing down the drain hose.  
• The end of the drain hose has been pushed too far down the standpipe, the  
‘U’ bracket should be fitted 100 mm from the end of the drain hose.  
The machine does not drain or  
spin.  
• The Pump filter is blocked.  
• The drain hose is kinked (see “Installation”).  
• New Installation - The blanking cap or spigot has not been removed if  
connected under a sink.  
• The drain hose or sink trap is blocked.  
• The wash cycle does not include draining, some wash cycles require the drain  
phase to be started manually.  
• The ‘Spin Speed’ selector knob is in the “ “position.  
The machine does not heat or poor • The ‘Temperature’ selector knob is in the “ ” position.  
wash results.  
The programme takes too long.  
• Programme times will vary due to water pressure, the incoming water tempera-  
ture and if the wash load goes out of balance. This will increase the programme  
times accordingly (see ‘ The machine wont spin properly’ below).  
The machine vibrates a lot during  
the spin cycle.  
• The feet have not been adjusted, enabling the machine to rock.  
• New Installation - Either the Transit Bolts including the plastic spacers, or the  
Polystyrene Packaging have not been removed when installing the machine.  
• The machine is trapped between cabinets and/or walls.  
• The load is in a slight out of balance condition and machine is spinning, but at  
a lower speed.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The machine is noisy.  
• There will always be some motor, pump and drum noise during spin.  
GB  
The machine wont spin properly.  
• Out of Balance detected when attempting to go into a spin cycle - If this  
happens the machine will continue to try to repeat the distribution of the load  
required before the machine will go into higher spin speeds - This will increase  
the programme time accordingly. This is a safety feature to prevent damage.  
Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,  
etc). - Try the programme again using a different load.  
The machine leaks from the  
dispenser.  
• The dispenser drawer is blocked with detergent and requires cleaning.  
• The water pressure is too high and requires turning down - turn down the tap  
on the water supply pipe slightly and try again.  
• The machine is tilting forwards - It must be level when in its final position.  
The machine leaks (other than  
dispenser).  
• The fill hose is loose, check both the cabinet and tap ends.  
• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill  
hose is missing the rubber washer.  
• The drain hose is not fixed in properly.  
The indicator lights on the console • Switch off the machine and unplug it, wait for approximately 1 minute and then  
are flashing rapidly.  
switch it back on again If the problem persists contact the Technical Assistance  
Service.  
The machine smells.  
• The machine requires a service wash. Run a 90 degree wash cycle with deter-  
gent and no laundry.  
The machine door cannot be  
opened.  
• The door will not open until the door lock indicator light goes out shortly after  
the program has finished.  
Door Seal damaged at the bottom. • The door seal has drainage holes at the bottom - This is normal.  
The water level is too low when  
the machine is washing.  
• The water level is correct if it can be seen at the bottom of the door.  
There is too much foam.  
• The detergent is not suitable for machine washing (it should display the text  
‘for washing machines’ or ‘hand and machine wash’ or the like).  
Too much detergent was used - less detergent is required in soft water.  
After completing the programme,  
or before starting a programme,  
the machine has turned itself off  
(no lights).  
To comply with new energy saving regulations the machine is fitted with an  
automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate  
the machine, it can then either be switched off or a new programme selected.  
General.  
Your washing machine contains sensors that monitor progress during the wash  
cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/pro-  
gress).  
Normally, if your machine successfully completes the cycle, there is unlikely to  
be anything wrong!  
Remember, you will be charged for a service call for problems caused by incorrect installation, as listed  
above.  
Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.  
Do not wash items which do not have a wash label, or wash items that are not intended as machine  
washable.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assistance  
12 Months Parts and Labour Guarantee  
GB  
Your appliance has the benefit of our manufacturers guarantee, which covers the cost of breakdown repairs for twelve  
months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either  
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our operating and  
maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any  
person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper  
installation.  
Replacement of any consumable item or accessory . These include but are not limited to:  
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR  
NON-DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Indesit also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering your appliance  
with us and the parts being fitted by one of our authorised engineers. There will be a charge for our engineers time. To  
activate the extra parts warranty on your appliance, simply call our registration line on 08448 24 24 24 (Republic of  
Ireland 01 230 0800)  
Extended Guarantees  
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills for the  
life of your policy. To find the ideal plan for you please call our advice line on  
08448 226 226 (Republic of Ireland 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you experience any technical  
difficulties within the first 90 days of ownership. Simply call our Indesit Service Hotline on 08448 224 224 (Republic of  
Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an engineer to call.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
195089417.00  
11/2010  
-
Xerox Fabriano  
After Sales Service  
GB  
No one is better placed to care for your Indesit appliance during the course of its working life than us - the manufacturer.  
Essential Contact Information  
Indesit Service  
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100 fully qualified  
engineers on call to ensure you receive fast, reliable, local service.  
UK: 08448 224 224  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following information:  
Model number:  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean your  
appliance to keep it looking good and functioning efficiently throughout its life.  
UK: 08448 225 225  
Republic of Ireland: 0818 313 413  
Appliance Registration  
We want to give you additional benefits of Indesit ownership. To activate your free 5 year parts guarantee you must  
register your appliance with us.  
UK: 08448 24 24 24  
Republic of Ireland: 01 230 0800  
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17  
Recycling & Disposal Information  
As part of Indesits continued commitment to helping the environment, Indesit reserves the right to use quality, recycled  
components to keep down customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the door, plug  
and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that the appliance can  
no longer be plugged into a mains socket, and the door cannot be locked shut.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Clothes Dryer G31 User Manual
Intel Network Card 21143 User Manual
Ironman Fitness Treadmill LEGACY User Manual
Jabra Headphones C220 User Manual
JVC CD Player KS FX385 User Manual
JVC DVD Recorder CU VD20U User Manual
JVC Stereo Receiver RX 7001PGD User Manual
Kenmore Water Dispenser ULTRAFILTER 300 625384720 User Manual
Kenwood Marine Radio TM 221A User Manual
Keys Fitness Treadmill PRO 750 User Manual